diff options
Diffstat (limited to 'drivers/usb/phy/Kconfig')
| -rw-r--r-- | drivers/usb/phy/Kconfig | 52 |
1 files changed, 47 insertions, 5 deletions
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig index 2b41c636a52..7d1451d5bbe 100644 --- a/drivers/usb/phy/Kconfig +++ b/drivers/usb/phy/Kconfig @@ -6,6 +6,15 @@ menu "USB Physical Layer drivers" config USB_PHY def_bool n +config USB_OTG_FSM + tristate "USB 2.0 OTG FSM implementation" + depends on USB + select USB_OTG + select USB_PHY + help + Implements OTG Final State Machine as specified in On-The-Go + and Embedded Host Supplement to the USB Revision 2.0 Specification. + # # USB Transceiver Drivers # @@ -19,9 +28,8 @@ config AB8500_USB in host mode, low speed. config FSL_USB2_OTG - tristate "Freescale USB OTG Transceiver Driver" - depends on USB_EHCI_FSL && USB_FSL_USB2 && PM_RUNTIME - depends on USB + bool "Freescale USB OTG Transceiver Driver" + depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM_RUNTIME select USB_OTG select USB_PHY help @@ -40,7 +48,16 @@ config ISP1301_OMAP Instruments OMAP processors. This driver can also be built as a module. If so, the module - will be called isp1301_omap. + will be called phy-isp1301-omap. + +config KEYSTONE_USB_PHY + tristate "Keystone USB PHY Driver" + depends on ARCH_KEYSTONE || COMPILE_TEST + select NOP_USB_XCEIV + help + Enable this to support Keystone USB phy. This driver provides + interface to interact with USB 2.0 and USB 3.0 PHY that is part + of the Keystone SOC. config MV_U3D_PHY bool "Marvell USB 3.0 PHY controller Driver" @@ -136,6 +153,31 @@ config USB_GPIO_VBUS optionally control of a D+ pullup GPIO as well as a VBUS current limit regulator. +config OMAP_OTG + tristate "OMAP USB OTG controller driver" + depends on ARCH_OMAP_OTG && EXTCON + help + Enable this to support some transceivers on OMAP1 platforms. OTG + controller is needed to switch between host and peripheral modes. + + This driver can also be built as a module. If so, the module + will be called phy-omap-otg. + +config TAHVO_USB + tristate "Tahvo USB transceiver driver" + depends on MFD_RETU && EXTCON + select USB_PHY + help + Enable this to support USB transceiver on Tahvo. This is used + at least on Nokia 770. + +config TAHVO_USB_HOST_BY_DEFAULT + depends on TAHVO_USB + boolean "Device in USB host mode by default" + help + Say Y here, if you want the device to enter USB host mode + by default on bootup. + config USB_ISP1301 tristate "NXP ISP1301 USB transceiver support" depends on USB || USB_GADGET @@ -147,7 +189,7 @@ config USB_ISP1301 and OTG drivers (to be selected separately). To compile this driver as a module, choose M here: the - module will be called isp1301. + module will be called phy-isp1301. config USB_MSM_OTG tristate "OTG support for Qualcomm on-chip USB controller" |