summaryrefslogtreecommitdiffstats
path: root/drivers/usb/phy
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/usb/phy')
-rw-r--r--drivers/usb/phy/Kconfig21
-rw-r--r--drivers/usb/phy/Makefile2
-rw-r--r--drivers/usb/phy/phy-fsm-usb.c9
-rw-r--r--drivers/usb/phy/phy-msm-usb.c3
-rw-r--r--drivers/usb/phy/phy-mxs-usb.c310
-rw-r--r--drivers/usb/phy/phy-omap-control.c319
-rw-r--r--drivers/usb/phy/phy-omap-usb3.c361
-rw-r--r--drivers/usb/phy/phy-rcar-gen2-usb.c6
-rw-r--r--drivers/usb/phy/phy-twl6030-usb.c2
-rw-r--r--drivers/usb/phy/phy-ulpi.c2
10 files changed, 309 insertions, 726 deletions
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index 7d1451d5bbe..416e0c8cf6f 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -75,27 +75,6 @@ config NOP_USB_XCEIV
built-in with usb ip or which are autonomous and doesn't require any
phy programming such as ISP1x04 etc.
-config OMAP_CONTROL_USB
- tristate "OMAP CONTROL USB Driver"
- depends on ARCH_OMAP2PLUS || COMPILE_TEST
- help
- Enable this to add support for the USB part present in the control
- module. This driver has API to power on the USB2 PHY and to write to
- the mailbox. The mailbox is present only in omap4 and the register to
- power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
- additional register to power on USB3 PHY.
-
-config OMAP_USB3
- tristate "OMAP USB3 PHY Driver"
- depends on ARCH_OMAP2PLUS || COMPILE_TEST
- select OMAP_CONTROL_USB
- select USB_PHY
- help
- Enable this to support the USB3 PHY that is part of SOC. This
- driver takes care of all the PHY functionality apart from comparator.
- This driver interacts with the "OMAP Control USB Driver" to power
- on/off the PHY.
-
config AM335X_CONTROL_USB
tristate
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index be58adae349..f8fa719a31b 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -13,11 +13,9 @@ obj-$(CONFIG_ISP1301_OMAP) += phy-isp1301-omap.o
obj-$(CONFIG_MV_U3D_PHY) += phy-mv-u3d-usb.o
obj-$(CONFIG_NOP_USB_XCEIV) += phy-generic.o
obj-$(CONFIG_TAHVO_USB) += phy-tahvo.o
-obj-$(CONFIG_OMAP_CONTROL_USB) += phy-omap-control.o
obj-$(CONFIG_AM335X_CONTROL_USB) += phy-am335x-control.o
obj-$(CONFIG_AM335X_PHY_USB) += phy-am335x.o
obj-$(CONFIG_OMAP_OTG) += phy-omap-otg.o
-obj-$(CONFIG_OMAP_USB3) += phy-omap-usb3.o
obj-$(CONFIG_SAMSUNG_USBPHY) += phy-samsung-usb.o
obj-$(CONFIG_SAMSUNG_USB2PHY) += phy-samsung-usb2.o
obj-$(CONFIG_SAMSUNG_USB3PHY) += phy-samsung-usb3.o
diff --git a/drivers/usb/phy/phy-fsm-usb.c b/drivers/usb/phy/phy-fsm-usb.c
index 7aa314ef4a8..c47e5a6edde 100644
--- a/drivers/usb/phy/phy-fsm-usb.c
+++ b/drivers/usb/phy/phy-fsm-usb.c
@@ -317,10 +317,12 @@ int otg_statemachine(struct otg_fsm *fsm)
otg_set_state(fsm, OTG_STATE_A_WAIT_VFALL);
break;
case OTG_STATE_A_HOST:
- if ((!fsm->a_bus_req || fsm->a_suspend_req_inf) &&
+ if (fsm->id || fsm->a_bus_drop)
+ otg_set_state(fsm, OTG_STATE_A_WAIT_VFALL);
+ else if ((!fsm->a_bus_req || fsm->a_suspend_req_inf) &&
fsm->otg->host->b_hnp_enable)
otg_set_state(fsm, OTG_STATE_A_SUSPEND);
- else if (fsm->id || !fsm->b_conn || fsm->a_bus_drop)
+ else if (!fsm->b_conn)
otg_set_state(fsm, OTG_STATE_A_WAIT_BCON);
else if (!fsm->a_vbus_vld)
otg_set_state(fsm, OTG_STATE_A_VBUS_ERR);
@@ -346,8 +348,7 @@ int otg_statemachine(struct otg_fsm *fsm)
otg_set_state(fsm, OTG_STATE_A_VBUS_ERR);
break;
case OTG_STATE_A_WAIT_VFALL:
- if (fsm->a_wait_vfall_tmout || fsm->id || fsm->a_bus_req ||
- (!fsm->a_sess_vld && !fsm->b_conn))
+ if (fsm->a_wait_vfall_tmout)
otg_set_state(fsm, OTG_STATE_A_IDLE);
break;
case OTG_STATE_A_VBUS_ERR:
diff --git a/drivers/usb/phy/phy-msm-usb.c b/drivers/usb/phy/phy-msm-usb.c
index d204f745ed0..5b37b81f2ef 100644
--- a/drivers/usb/phy/phy-msm-usb.c
+++ b/drivers/usb/phy/phy-msm-usb.c
@@ -1428,7 +1428,8 @@ static int __init msm_otg_probe(struct platform_device *pdev)
motg->phy.otg = kzalloc(sizeof(struct usb_otg), GFP_KERNEL);
if (!motg->phy.otg) {
dev_err(&pdev->dev, "unable to allocate msm_otg\n");
- return -ENOMEM;
+ ret = -ENOMEM;
+ goto free_motg;
}
motg->pdata = dev_get_platdata(&pdev->dev);
diff --git a/drivers/usb/phy/phy-mxs-usb.c b/drivers/usb/phy/phy-mxs-usb.c
index b42897b6474..c42bdf0c4a1 100644
--- a/drivers/usb/phy/phy-mxs-usb.c
+++ b/drivers/usb/phy/phy-mxs-usb.c
@@ -1,5 +1,5 @@
/*
- * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2012-2013 Freescale Semiconductor, Inc.
* Copyright (C) 2012 Marek Vasut <marex@denx.de>
* on behalf of DENX Software Engineering GmbH
*
@@ -20,6 +20,9 @@
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/io.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
#define DRIVER_NAME "mxs_phy"
@@ -28,18 +31,134 @@
#define HW_USBPHY_CTRL_SET 0x34
#define HW_USBPHY_CTRL_CLR 0x38
+#define HW_USBPHY_DEBUG_SET 0x54
+#define HW_USBPHY_DEBUG_CLR 0x58
+
+#define HW_USBPHY_IP 0x90
+#define HW_USBPHY_IP_SET 0x94
+#define HW_USBPHY_IP_CLR 0x98
+
#define BM_USBPHY_CTRL_SFTRST BIT(31)
#define BM_USBPHY_CTRL_CLKGATE BIT(30)
+#define BM_USBPHY_CTRL_ENAUTOSET_USBCLKS BIT(26)
+#define BM_USBPHY_CTRL_ENAUTOCLR_USBCLKGATE BIT(25)
+#define BM_USBPHY_CTRL_ENVBUSCHG_WKUP BIT(23)
+#define BM_USBPHY_CTRL_ENIDCHG_WKUP BIT(22)
+#define BM_USBPHY_CTRL_ENDPDMCHG_WKUP BIT(21)
+#define BM_USBPHY_CTRL_ENAUTOCLR_PHY_PWD BIT(20)
+#define BM_USBPHY_CTRL_ENAUTOCLR_CLKGATE BIT(19)
+#define BM_USBPHY_CTRL_ENAUTO_PWRON_PLL BIT(18)
#define BM_USBPHY_CTRL_ENUTMILEVEL3 BIT(15)
#define BM_USBPHY_CTRL_ENUTMILEVEL2 BIT(14)
#define BM_USBPHY_CTRL_ENHOSTDISCONDETECT BIT(1)
+#define BM_USBPHY_IP_FIX (BIT(17) | BIT(18))
+
+#define BM_USBPHY_DEBUG_CLKGATE BIT(30)
+
+/* Anatop Registers */
+#define ANADIG_ANA_MISC0 0x150
+#define ANADIG_ANA_MISC0_SET 0x154
+#define ANADIG_ANA_MISC0_CLR 0x158
+
+#define ANADIG_USB1_VBUS_DET_STAT 0x1c0
+#define ANADIG_USB2_VBUS_DET_STAT 0x220
+
+#define ANADIG_USB1_LOOPBACK_SET 0x1e4
+#define ANADIG_USB1_LOOPBACK_CLR 0x1e8
+#define ANADIG_USB2_LOOPBACK_SET 0x244
+#define ANADIG_USB2_LOOPBACK_CLR 0x248
+
+#define BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG BIT(12)
+#define BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG_SL BIT(11)
+
+#define BM_ANADIG_USB1_VBUS_DET_STAT_VBUS_VALID BIT(3)
+#define BM_ANADIG_USB2_VBUS_DET_STAT_VBUS_VALID BIT(3)
+
+#define BM_ANADIG_USB1_LOOPBACK_UTMI_DIG_TST1 BIT(2)
+#define BM_ANADIG_USB1_LOOPBACK_TSTI_TX_EN BIT(5)
+#define BM_ANADIG_USB2_LOOPBACK_UTMI_DIG_TST1 BIT(2)
+#define BM_ANADIG_USB2_LOOPBACK_TSTI_TX_EN BIT(5)
+
+#define to_mxs_phy(p) container_of((p), struct mxs_phy, phy)
+
+/* Do disconnection between PHY and controller without vbus */
+#define MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS BIT(0)
+
+/*
+ * The PHY will be in messy if there is a wakeup after putting
+ * bus to suspend (set portsc.suspendM) but before setting PHY to low
+ * power mode (set portsc.phcd).
+ */
+#define MXS_PHY_ABNORMAL_IN_SUSPEND BIT(1)
+
+/*
+ * The SOF sends too fast after resuming, it will cause disconnection
+ * between host and high speed device.
+ */
+#define MXS_PHY_SENDING_SOF_TOO_FAST BIT(2)
+
+/*
+ * IC has bug fixes logic, they include
+ * MXS_PHY_ABNORMAL_IN_SUSPEND and MXS_PHY_SENDING_SOF_TOO_FAST
+ * which are described at above flags, the RTL will handle it
+ * according to different versions.
+ */
+#define MXS_PHY_NEED_IP_FIX BIT(3)
+
+struct mxs_phy_data {
+ unsigned int flags;
+};
+
+static const struct mxs_phy_data imx23_phy_data = {
+ .flags = MXS_PHY_ABNORMAL_IN_SUSPEND | MXS_PHY_SENDING_SOF_TOO_FAST,
+};
+
+static const struct mxs_phy_data imx6q_phy_data = {
+ .flags = MXS_PHY_SENDING_SOF_TOO_FAST |
+ MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS |
+ MXS_PHY_NEED_IP_FIX,
+};
+
+static const struct mxs_phy_data imx6sl_phy_data = {
+ .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS |
+ MXS_PHY_NEED_IP_FIX,
+};
+
+static const struct of_device_id mxs_phy_dt_ids[] = {
+ { .compatible = "fsl,imx6sl-usbphy", .data = &imx6sl_phy_data, },
+ { .compatible = "fsl,imx6q-usbphy", .data = &imx6q_phy_data, },
+ { .compatible = "fsl,imx23-usbphy", .data = &imx23_phy_data, },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mxs_phy_dt_ids);
+
struct mxs_phy {
struct usb_phy phy;
struct clk *clk;
+ const struct mxs_phy_data *data;
+ struct regmap *regmap_anatop;
+ int port_id;
};
-#define to_mxs_phy(p) container_of((p), struct mxs_phy, phy)
+static inline bool is_imx6q_phy(struct mxs_phy *mxs_phy)
+{
+ return mxs_phy->data == &imx6q_phy_data;
+}
+
+static inline bool is_imx6sl_phy(struct mxs_phy *mxs_phy)
+{
+ return mxs_phy->data == &imx6sl_phy_data;
+}
+
+/*
+ * PHY needs some 32K cycles to switch from 32K clock to
+ * bus (such as AHB/AXI, etc) clock.
+ */
+static void mxs_phy_clock_switch_delay(void)
+{
+ usleep_range(300, 400);
+}
static int mxs_phy_hw_init(struct mxs_phy *mxs_phy)
{
@@ -53,19 +172,105 @@ static int mxs_phy_hw_init(struct mxs_phy *mxs_phy)
/* Power up the PHY */
writel(0, base + HW_USBPHY_PWD);
- /* enable FS/LS device */
- writel(BM_USBPHY_CTRL_ENUTMILEVEL2 |
- BM_USBPHY_CTRL_ENUTMILEVEL3,
+ /*
+ * USB PHY Ctrl Setting
+ * - Auto clock/power on
+ * - Enable full/low speed support
+ */
+ writel(BM_USBPHY_CTRL_ENAUTOSET_USBCLKS |
+ BM_USBPHY_CTRL_ENAUTOCLR_USBCLKGATE |
+ BM_USBPHY_CTRL_ENAUTOCLR_PHY_PWD |
+ BM_USBPHY_CTRL_ENAUTOCLR_CLKGATE |
+ BM_USBPHY_CTRL_ENAUTO_PWRON_PLL |
+ BM_USBPHY_CTRL_ENUTMILEVEL2 |
+ BM_USBPHY_CTRL_ENUTMILEVEL3,
base + HW_USBPHY_CTRL_SET);
+ if (mxs_phy->data->flags & MXS_PHY_NEED_IP_FIX)
+ writel(BM_USBPHY_IP_FIX, base + HW_USBPHY_IP_SET);
+
return 0;
}
+/* Return true if the vbus is there */
+static bool mxs_phy_get_vbus_status(struct mxs_phy *mxs_phy)
+{
+ unsigned int vbus_value;
+
+ if (mxs_phy->port_id == 0)
+ regmap_read(mxs_phy->regmap_anatop,
+ ANADIG_USB1_VBUS_DET_STAT,
+ &vbus_value);
+ else if (mxs_phy->port_id == 1)
+ regmap_read(mxs_phy->regmap_anatop,
+ ANADIG_USB2_VBUS_DET_STAT,
+ &vbus_value);
+
+ if (vbus_value & BM_ANADIG_USB1_VBUS_DET_STAT_VBUS_VALID)
+ return true;
+ else
+ return false;
+}
+
+static void __mxs_phy_disconnect_line(struct mxs_phy *mxs_phy, bool disconnect)
+{
+ void __iomem *base = mxs_phy->phy.io_priv;
+ u32 reg;
+
+ if (disconnect)
+ writel_relaxed(BM_USBPHY_DEBUG_CLKGATE,
+ base + HW_USBPHY_DEBUG_CLR);
+
+ if (mxs_phy->port_id == 0) {
+ reg = disconnect ? ANADIG_USB1_LOOPBACK_SET
+ : ANADIG_USB1_LOOPBACK_CLR;
+ regmap_write(mxs_phy->regmap_anatop, reg,
+ BM_ANADIG_USB1_LOOPBACK_UTMI_DIG_TST1 |
+ BM_ANADIG_USB1_LOOPBACK_TSTI_TX_EN);
+ } else if (mxs_phy->port_id == 1) {
+ reg = disconnect ? ANADIG_USB2_LOOPBACK_SET
+ : ANADIG_USB2_LOOPBACK_CLR;
+ regmap_write(mxs_phy->regmap_anatop, reg,
+ BM_ANADIG_USB2_LOOPBACK_UTMI_DIG_TST1 |
+ BM_ANADIG_USB2_LOOPBACK_TSTI_TX_EN);
+ }
+
+ if (!disconnect)
+ writel_relaxed(BM_USBPHY_DEBUG_CLKGATE,
+ base + HW_USBPHY_DEBUG_SET);
+
+ /* Delay some time, and let Linestate be SE0 for controller */
+ if (disconnect)
+ usleep_range(500, 1000);
+}
+
+static void mxs_phy_disconnect_line(struct mxs_phy *mxs_phy, bool on)
+{
+ bool vbus_is_on = false;
+
+ /* If the SoCs don't need to disconnect line without vbus, quit */
+ if (!(mxs_phy->data->flags & MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS))
+ return;
+
+ /* If the SoCs don't have anatop, quit */
+ if (!mxs_phy->regmap_anatop)
+ return;
+
+ vbus_is_on = mxs_phy_get_vbus_status(mxs_phy);
+
+ if (on && !vbus_is_on)
+ __mxs_phy_disconnect_line(mxs_phy, true);
+ else
+ __mxs_phy_disconnect_line(mxs_phy, false);
+
+}
+
static int mxs_phy_init(struct usb_phy *phy)
{
int ret;
struct mxs_phy *mxs_phy = to_mxs_phy(phy);
+ mxs_phy_clock_switch_delay();
ret = clk_prepare_enable(mxs_phy->clk);
if (ret)
return ret;
@@ -94,6 +299,7 @@ static int mxs_phy_suspend(struct usb_phy *x, int suspend)
x->io_priv + HW_USBPHY_CTRL_SET);
clk_disable_unprepare(mxs_phy->clk);
} else {
+ mxs_phy_clock_switch_delay();
ret = clk_prepare_enable(mxs_phy->clk);
if (ret)
return ret;
@@ -105,11 +311,28 @@ static int mxs_phy_suspend(struct usb_phy *x, int suspend)
return 0;
}
+static int mxs_phy_set_wakeup(struct usb_phy *x, bool enabled)
+{
+ struct mxs_phy *mxs_phy = to_mxs_phy(x);
+ u32 value = BM_USBPHY_CTRL_ENVBUSCHG_WKUP |
+ BM_USBPHY_CTRL_ENDPDMCHG_WKUP |
+ BM_USBPHY_CTRL_ENIDCHG_WKUP;
+ if (enabled) {
+ mxs_phy_disconnect_line(mxs_phy, true);
+ writel_relaxed(value, x->io_priv + HW_USBPHY_CTRL_SET);
+ } else {
+ writel_relaxed(value, x->io_priv + HW_USBPHY_CTRL_CLR);
+ mxs_phy_disconnect_line(mxs_phy, false);
+ }
+
+ return 0;
+}
+
static int mxs_phy_on_connect(struct usb_phy *phy,
enum usb_device_speed speed)
{
- dev_dbg(phy->dev, "%s speed device has connected\n",
- (speed == USB_SPEED_HIGH) ? "high" : "non-high");
+ dev_dbg(phy->dev, "%s device has connected\n",
+ (speed == USB_SPEED_HIGH) ? "HS" : "FS/LS");
if (speed == USB_SPEED_HIGH)
writel(BM_USBPHY_CTRL_ENHOSTDISCONDETECT,
@@ -121,8 +344,8 @@ static int mxs_phy_on_connect(struct usb_phy *phy,
static int mxs_phy_on_disconnect(struct usb_phy *phy,
enum usb_device_speed speed)
{
- dev_dbg(phy->dev, "%s speed device has disconnected\n",
- (speed == USB_SPEED_HIGH) ? "high" : "non-high");
+ dev_dbg(phy->dev, "%s device has disconnected\n",
+ (speed == USB_SPEED_HIGH) ? "HS" : "FS/LS");
if (speed == USB_SPEED_HIGH)
writel(BM_USBPHY_CTRL_ENHOSTDISCONDETECT,
@@ -138,6 +361,9 @@ static int mxs_phy_probe(struct platform_device *pdev)
struct clk *clk;
struct mxs_phy *mxs_phy;
int ret;
+ const struct of_device_id *of_id =
+ of_match_device(mxs_phy_dt_ids, &pdev->dev);
+ struct device_node *np = pdev->dev.of_node;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
base = devm_ioremap_resource(&pdev->dev, res);
@@ -157,6 +383,22 @@ static int mxs_phy_probe(struct platform_device *pdev)
return -ENOMEM;
}
+ /* Some SoCs don't have anatop registers */
+ if (of_get_property(np, "fsl,anatop", NULL)) {
+ mxs_phy->regmap_anatop = syscon_regmap_lookup_by_phandle
+ (np, "fsl,anatop");
+ if (IS_ERR(mxs_phy->regmap_anatop)) {
+ dev_dbg(&pdev->dev,
+ "failed to find regmap for anatop\n");
+ return PTR_ERR(mxs_phy->regmap_anatop);
+ }
+ }
+
+ ret = of_alias_get_id(np, "usbphy");
+ if (ret < 0)
+ dev_dbg(&pdev->dev, "failed to get alias id, errno %d\n", ret);
+ mxs_phy->port_id = ret;
+
mxs_phy->phy.io_priv = base;
mxs_phy->phy.dev = &pdev->dev;
mxs_phy->phy.label = DRIVER_NAME;
@@ -166,11 +408,15 @@ static int mxs_phy_probe(struct platform_device *pdev)
mxs_phy->phy.notify_connect = mxs_phy_on_connect;
mxs_phy->phy.notify_disconnect = mxs_phy_on_disconnect;
mxs_phy->phy.type = USB_PHY_TYPE_USB2;
+ mxs_phy->phy.set_wakeup = mxs_phy_set_wakeup;
mxs_phy->clk = clk;
+ mxs_phy->data = of_id->data;
platform_set_drvdata(pdev, mxs_phy);
+ device_set_wakeup_capable(&pdev->dev, true);
+
ret = usb_add_phy_dev(&mxs_phy->phy);
if (ret)
return ret;
@@ -187,11 +433,46 @@ static int mxs_phy_remove(struct platform_device *pdev)
return 0;
}
-static const struct of_device_id mxs_phy_dt_ids[] = {
- { .compatible = "fsl,imx23-usbphy", },
- { /* sentinel */ }
-};
-MODULE_DEVICE_TABLE(of, mxs_phy_dt_ids);
+#ifdef CONFIG_PM_SLEEP
+static void mxs_phy_enable_ldo_in_suspend(struct mxs_phy *mxs_phy, bool on)
+{
+ unsigned int reg = on ? ANADIG_ANA_MISC0_SET : ANADIG_ANA_MISC0_CLR;
+
+ /* If the SoCs don't have anatop, quit */
+ if (!mxs_phy->regmap_anatop)
+ return;
+
+ if (is_imx6q_phy(mxs_phy))
+ regmap_write(mxs_phy->regmap_anatop, reg,
+ BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG);
+ else if (is_imx6sl_phy(mxs_phy))
+ regmap_write(mxs_phy->regmap_anatop,
+ reg, BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG_SL);
+}
+
+static int mxs_phy_system_suspend(struct device *dev)
+{
+ struct mxs_phy *mxs_phy = dev_get_drvdata(dev);
+
+ if (device_may_wakeup(dev))
+ mxs_phy_enable_ldo_in_suspend(mxs_phy, true);
+
+ return 0;
+}
+
+static int mxs_phy_system_resume(struct device *dev)
+{
+ struct mxs_phy *mxs_phy = dev_get_drvdata(dev);
+
+ if (device_may_wakeup(dev))
+ mxs_phy_enable_ldo_in_suspend(mxs_phy, false);
+
+ return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+static SIMPLE_DEV_PM_OPS(mxs_phy_pm, mxs_phy_system_suspend,
+ mxs_phy_system_resume);
static struct platform_driver mxs_phy_driver = {
.probe = mxs_phy_probe,
@@ -200,6 +481,7 @@ static struct platform_driver mxs_phy_driver = {
.name = DRIVER_NAME,
.owner = THIS_MODULE,
.of_match_table = mxs_phy_dt_ids,
+ .pm = &mxs_phy_pm,
},
};
diff --git a/drivers/usb/phy/phy-omap-control.c b/drivers/usb/phy/phy-omap-control.c
deleted file mode 100644
index e7253182e47..00000000000
--- a/drivers/usb/phy/phy-omap-control.c
+++ /dev/null
@@ -1,319 +0,0 @@
-/*
- * omap-control-usb.c - The USB part of control module.
- *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * Author: Kishon Vijay Abraham I <kishon@ti.com>
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/slab.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/clk.h>
-#include <linux/usb/omap_control_usb.h>
-
-/**
- * omap_control_usb_phy_power - power on/off the phy using control module reg
- * @dev: the control module device
- * @on: 0 or 1, based on powering on or off the PHY
- */
-void omap_control_usb_phy_power(struct device *dev, int on)
-{
- u32 val;
- unsigned long rate;
- struct omap_control_usb *control_usb;
-
- if (IS_ERR(dev) || !dev) {
- pr_err("%s: invalid device\n", __func__);
- return;
- }
-
- control_usb = dev_get_drvdata(dev);
- if (!control_usb) {
- dev_err(dev, "%s: invalid control usb device\n", __func__);
- return;
- }
-
- if (control_usb->type == OMAP_CTRL_TYPE_OTGHS)
- return;
-
- val = readl(control_usb->power);
-
- switch (control_usb->type) {
- case OMAP_CTRL_TYPE_USB2:
- if (on)
- val &= ~OMAP_CTRL_DEV_PHY_PD;
- else
- val |= OMAP_CTRL_DEV_PHY_PD;
- break;
-
- case OMAP_CTRL_TYPE_PIPE3:
- rate = clk_get_rate(control_usb->sys_clk);
- rate = rate/1000000;
-
- if (on) {
- val &= ~(OMAP_CTRL_USB_PWRCTL_CLK_CMD_MASK |
- OMAP_CTRL_USB_PWRCTL_CLK_FREQ_MASK);
- val |= OMAP_CTRL_USB3_PHY_TX_RX_POWERON <<
- OMAP_CTRL_USB_PWRCTL_CLK_CMD_SHIFT;
- val |= rate << OMAP_CTRL_USB_PWRCTL_CLK_FREQ_SHIFT;
- } else {
- val &= ~OMAP_CTRL_USB_PWRCTL_CLK_CMD_MASK;
- val |= OMAP_CTRL_USB3_PHY_TX_RX_POWEROFF <<
- OMAP_CTRL_USB_PWRCTL_CLK_CMD_SHIFT;
- }
- break;
-
- case OMAP_CTRL_TYPE_DRA7USB2:
- if (on)
- val &= ~OMAP_CTRL_USB2_PHY_PD;
- else
- val |= OMAP_CTRL_USB2_PHY_PD;
- break;
-
- case OMAP_CTRL_TYPE_AM437USB2:
- if (on) {
- val &= ~(AM437X_CTRL_USB2_PHY_PD |
- AM437X_CTRL_USB2_OTG_PD);
- val |= (AM437X_CTRL_USB2_OTGVDET_EN |
- AM437X_CTRL_USB2_OTGSESSEND_EN);
- } else {
- val &= ~(AM437X_CTRL_USB2_OTGVDET_EN |
- AM437X_CTRL_USB2_OTGSESSEND_EN);
- val |= (AM437X_CTRL_USB2_PHY_PD |
- AM437X_CTRL_USB2_OTG_PD);
- }
- break;
- default:
- dev_err(dev, "%s: type %d not recognized\n",
- __func__, control_usb->type);
- break;
- }
-
- writel(val, control_usb->power);
-}
-EXPORT_SYMBOL_GPL(omap_control_usb_phy_power);
-
-/**
- * omap_control_usb_host_mode - set AVALID, VBUSVALID and ID pin in grounded
- * @ctrl_usb: struct omap_control_usb *
- *
- * Writes to the mailbox register to notify the usb core that a usb
- * device has been connected.
- */
-static void omap_control_usb_host_mode(struct omap_control_usb *ctrl_usb)
-{
- u32 val;
-
- val = readl(ctrl_usb->otghs_control);
- val &= ~(OMAP_CTRL_DEV_IDDIG | OMAP_CTRL_DEV_SESSEND);
- val |= OMAP_CTRL_DEV_AVALID | OMAP_CTRL_DEV_VBUSVALID;
- writel(val, ctrl_usb->otghs_control);
-}
-
-/**
- * omap_control_usb_device_mode - set AVALID, VBUSVALID and ID pin in high
- * impedance
- * @ctrl_usb: struct omap_control_usb *
- *
- * Writes to the mailbox register to notify the usb core that it has been
- * connected to a usb host.
- */
-static void omap_control_usb_device_mode(struct omap_control_usb *ctrl_usb)
-{
- u32 val;
-
- val = readl(ctrl_usb->otghs_control);
- val &= ~OMAP_CTRL_DEV_SESSEND;
- val |= OMAP_CTRL_DEV_IDDIG | OMAP_CTRL_DEV_AVALID |
- OMAP_CTRL_DEV_VBUSVALID;
- writel(val, ctrl_usb->otghs_control);
-}
-
-/**
- * omap_control_usb_set_sessionend - Enable SESSIONEND and IDIG to high
- * impedance
- * @ctrl_usb: struct omap_control_usb *
- *
- * Writes to the mailbox register to notify the usb core it's now in
- * disconnected state.
- */
-static void omap_control_usb_set_sessionend(struct omap_control_usb *ctrl_usb)
-{
- u32 val;
-
- val = readl(ctrl_usb->otghs_control);
- val &= ~(OMAP_CTRL_DEV_AVALID | OMAP_CTRL_DEV_VBUSVALID);
- val |= OMAP_CTRL_DEV_IDDIG | OMAP_CTRL_DEV_SESSEND;
- writel(val, ctrl_usb->otghs_control);
-}
-
-/**
- * omap_control_usb_set_mode - Calls to functions to set USB in one of host mode
- * or device mode or to denote disconnected state
- * @dev: the control module device
- * @mode: The mode to which usb should be configured
- *
- * This is an API to write to the mailbox register to notify the usb core that
- * a usb device has been connected.
- */
-void omap_control_usb_set_mode(struct device *dev,
- enum omap_control_usb_mode mode)
-{
- struct omap_control_usb *ctrl_usb;
-
- if (IS_ERR(dev) || !dev)
- return;
-
- ctrl_usb = dev_get_drvdata(dev);
-
- if (!ctrl_usb) {
- dev_err(dev, "Invalid control usb device\n");
- return;
- }
-
- if (ctrl_usb->type != OMAP_CTRL_TYPE_OTGHS)
- return;
-
- switch (mode) {
- case USB_MODE_HOST:
- omap_control_usb_host_mode(ctrl_usb);
- break;
- case USB_MODE_DEVICE:
- omap_control_usb_device_mode(ctrl_usb);
- break;
- case USB_MODE_DISCONNECT:
- omap_control_usb_set_sessionend(ctrl_usb);
- break;
- default:
- dev_vdbg(dev, "invalid omap control usb mode\n");
- }
-}
-EXPORT_SYMBOL_GPL(omap_control_usb_set_mode);
-
-#ifdef CONFIG_OF
-
-static const enum omap_control_usb_type otghs_data = OMAP_CTRL_TYPE_OTGHS;
-static const enum omap_control_usb_type usb2_data = OMAP_CTRL_TYPE_USB2;
-static const enum omap_control_usb_type pipe3_data = OMAP_CTRL_TYPE_PIPE3;
-static const enum omap_control_usb_type dra7usb2_data = OMAP_CTRL_TYPE_DRA7USB2;
-static const enum omap_control_usb_type am437usb2_data = OMAP_CTRL_TYPE_AM437USB2;
-
-static const struct of_device_id omap_control_usb_id_table[] = {
- {
- .compatible = "ti,control-phy-otghs",
- .data = &otghs_data,
- },
- {
- .compatible = "ti,control-phy-usb2",
- .data = &usb2_data,
- },
- {
- .compatible = "ti,control-phy-pipe3",
- .data = &pipe3_data,
- },
- {
- .compatible = "ti,control-phy-dra7usb2",
- .data = &dra7usb2_data,
- },
- {
- .compatible = "ti,control-phy-am437usb2",
- .data = &am437usb2_data,
- },
- {},
-};
-MODULE_DEVICE_TABLE(of, omap_control_usb_id_table);
-#endif
-
-
-static int omap_control_usb_probe(struct platform_device *pdev)
-{
- struct resource *res;
- const struct of_device_id *of_id;
- struct omap_control_usb *control_usb;
-
- of_id = of_match_device(of_match_ptr(omap_control_usb_id_table),
- &pdev->dev);
- if (!of_id)
- return -EINVAL;
-
- control_usb = devm_kzalloc(&pdev->dev, sizeof(*control_usb),
- GFP_KERNEL);
- if (!control_usb) {
- dev_err(&pdev->dev, "unable to alloc memory for control usb\n");
- return -ENOMEM;
- }
-
- control_usb->dev = &pdev->dev;
- control_usb->type = *(enum omap_control_usb_type *)of_id->data;
-
- if (control_usb->type == OMAP_CTRL_TYPE_OTGHS) {
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
- "otghs_control");
- control_usb->otghs_control = devm_ioremap_resource(
- &pdev->dev, res);
- if (IS_ERR(control_usb->otghs_control))
- return PTR_ERR(control_usb->otghs_control);
- } else {
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
- "power");
- control_usb->power = devm_ioremap_resource(&pdev->dev, res);
- if (IS_ERR(control_usb->power)) {
- dev_err(&pdev->dev, "Couldn't get power register\n");
- return PTR_ERR(control_usb->power);
- }
- }
-
- if (control_usb->type == OMAP_CTRL_TYPE_PIPE3) {
- control_usb->sys_clk = devm_clk_get(control_usb->dev,
- "sys_clkin");
- if (IS_ERR(control_usb->sys_clk)) {
- pr_err("%s: unable to get sys_clkin\n", __func__);
- return -EINVAL;
- }
- }
-
- dev_set_drvdata(control_usb->dev, control_usb);
-
- return 0;
-}
-
-static struct platform_driver omap_control_usb_driver = {
- .probe = omap_control_usb_probe,
- .driver = {
- .name = "omap-control-usb",
- .owner = THIS_MODULE,
- .of_match_table = of_match_ptr(omap_control_usb_id_table),
- },
-};
-
-static int __init omap_control_usb_init(void)
-{
- return platform_driver_register(&omap_control_usb_driver);
-}
-subsys_initcall(omap_control_usb_init);
-
-static void __exit omap_control_usb_exit(void)
-{
- platform_driver_unregister(&omap_control_usb_driver);
-}
-module_exit(omap_control_usb_exit);
-
-MODULE_ALIAS("platform: omap_control_usb");
-MODULE_AUTHOR("Texas Instruments Inc.");
-MODULE_DESCRIPTION("OMAP Control Module USB Driver");
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/usb/phy/phy-omap-usb3.c b/drivers/usb/phy/phy-omap-usb3.c
deleted file mode 100644
index 0c6ba29bddd..00000000000
--- a/drivers/usb/phy/phy-omap-usb3.c
+++ /dev/null
@@ -1,361 +0,0 @@
-/*
- * omap-usb3 - USB PHY, talking to dwc3 controller in OMAP.
- *
- * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * Author: Kishon Vijay Abraham I <kishon@ti.com>
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/slab.h>
-#include <linux/usb/omap_usb.h>
-#include <linux/of.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/pm_runtime.h>
-#include <linux/delay.h>
-#include <linux/usb/omap_control_usb.h>
-#include <linux/of_platform.h>
-
-#define PLL_STATUS 0x00000004
-#define PLL_GO 0x00000008
-#define PLL_CONFIGURATION1 0x0000000C
-#define PLL_CONFIGURATION2 0x00000010
-#define PLL_CONFIGURATION3 0x00000014
-#define PLL_CONFIGURATION4 0x00000020
-
-#define PLL_REGM_MASK 0x001FFE00
-#define PLL_REGM_SHIFT 0x9
-#define PLL_REGM_F_MASK 0x0003FFFF
-#define PLL_REGM_F_SHIFT 0x0
-#define PLL_REGN_MASK 0x000001FE
-#define PLL_REGN_SHIFT 0x1
-#define PLL_SELFREQDCO_MASK 0x0000000E
-#define PLL_SELFREQDCO_SHIFT 0x1
-#define PLL_SD_MASK 0x0003FC00
-#define PLL_SD_SHIFT 0x9
-#define SET_PLL_GO 0x1
-#define PLL_TICOPWDN 0x10000
-#define PLL_LOCK 0x2
-#define PLL_IDLE 0x1
-
-/*
- * This is an Empirical value that works, need to confirm the actual
- * value required for the USB3PHY_PLL_CONFIGURATION2.PLL_IDLE status
- * to be correctly reflected in the USB3PHY_PLL_STATUS register.
- */
-# define PLL_IDLE_TIME 100;
-
-struct usb_dpll_map {
- unsigned long rate;
- struct usb_dpll_params params;
-};
-
-static struct usb_dpll_map dpll_map[] = {
- {12000000, {1250, 5, 4, 20, 0} }, /* 12 MHz */
- {16800000, {3125, 20, 4, 20, 0} }, /* 16.8 MHz */
- {19200000, {1172, 8, 4, 20, 65537} }, /* 19.2 MHz */
- {20000000, {1000, 7, 4, 10, 0} }, /* 20 MHz */
- {26000000, {1250, 12, 4, 20, 0} }, /* 26 MHz */
- {38400000, {3125, 47, 4, 20, 92843} }, /* 38.4 MHz */
-};
-
-static struct usb_dpll_params *omap_usb3_get_dpll_params(unsigned long rate)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(dpll_map); i++) {
- if (rate == dpll_map[i].rate)
- return &dpll_map[i].params;
- }
-
- return NULL;
-}
-
-static int omap_usb3_suspend(struct usb_phy *x, int suspend)
-{
- struct omap_usb *phy = phy_to_omapusb(x);
- int val;
- int timeout = PLL_IDLE_TIME;
-
- if (suspend && !phy->is_suspended) {
- val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
- val |= PLL_IDLE;
- omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);
-
- do {
- val = omap_usb_readl(phy->pll_ctrl_base, PLL_STATUS);
- if (val & PLL_TICOPWDN)
- break;
- udelay(1);
- } while (--timeout);
-
- omap_control_usb_phy_power(phy->control_dev, 0);
-
- phy->is_suspended = 1;
- } else if (!suspend && phy->is_suspended) {
- phy->is_suspended = 0;
-
- val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
- val &= ~PLL_IDLE;
- omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);
-
- do {
- val = omap_usb_readl(phy->pll_ctrl_base, PLL_STATUS);
- if (!(val & PLL_TICOPWDN))
- break;
- udelay(1);
- } while (--timeout);
- }
-
- return 0;
-}
-
-static void omap_usb_dpll_relock(struct omap_usb *phy)
-{
- u32 val;
- unsigned long timeout;
-
- omap_usb_writel(phy->pll_ctrl_base, PLL_GO, SET_PLL_GO);
-
- timeout = jiffies + msecs_to_jiffies(20);
- do {
- val = omap_usb_readl(phy->pll_ctrl_base, PLL_STATUS);
- if (val & PLL_LOCK)
- break;
- } while (!WARN_ON(time_after(jiffies, timeout)));
-}
-
-static int omap_usb_dpll_lock(struct omap_usb *phy)
-{
- u32 val;
- unsigned long rate;
- struct usb_dpll_params *dpll_params;
-
- rate = clk_get_rate(phy->sys_clk);
- dpll_params = omap_usb3_get_dpll_params(rate);
- if (!dpll_params) {
- dev_err(phy->dev,
- "No DPLL configuration for %lu Hz SYS CLK\n", rate);
- return -EINVAL;
- }
-
- val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
- val &= ~PLL_REGN_MASK;
- val |= dpll_params->n << PLL_REGN_SHIFT;
- omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);
-
- val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
- val &= ~PLL_SELFREQDCO_MASK;
- val |= dpll_params->freq << PLL_SELFREQDCO_SHIFT;
- omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);
-
- val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
- val &= ~PLL_REGM_MASK;
- val |= dpll_params->m << PLL_REGM_SHIFT;
- omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);
-
- val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION4);
- val &= ~PLL_REGM_F_MASK;
- val |= dpll_params->mf << PLL_REGM_F_SHIFT;
- omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION4, val);
-
- val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION3);
- val &= ~PLL_SD_MASK;
- val |= dpll_params->sd << PLL_SD_SHIFT;
- omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION3, val);
-
- omap_usb_dpll_relock(phy);
-
- return 0;
-}
-
-static int omap_usb3_init(struct usb_phy *x)
-{
- struct omap_usb *phy = phy_to_omapusb(x);
- int ret;
-
- ret = omap_usb_dpll_lock(phy);
- if (ret)
- return ret;
-
- omap_control_usb_phy_power(phy->control_dev, 1);
-
- return 0;
-}
-
-static int omap_usb3_probe(struct platform_device *pdev)
-{
- struct omap_usb *phy;
- struct resource *res;
- struct device_node *node = pdev->dev.of_node;
- struct device_node *control_node;
- struct platform_device *control_pdev;
-
- if (!node)
- return -EINVAL;
-
- phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
- if (!phy) {
- dev_err(&pdev->dev, "unable to alloc mem for OMAP USB3 PHY\n");
- return -ENOMEM;
- }
-
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pll_ctrl");
- phy->pll_ctrl_base = devm_ioremap_resource(&pdev->dev, res);
- if (IS_ERR(phy->pll_ctrl_base))
- return PTR_ERR(phy->pll_ctrl_base);
-
- phy->dev = &pdev->dev;
-
- phy->phy.dev = phy->dev;
- phy->phy.label = "omap-usb3";
- phy->phy.init = omap_usb3_init;
- phy->phy.set_suspend = omap_usb3_suspend;
- phy->phy.type = USB_PHY_TYPE_USB3;
-
- phy->is_suspended = 1;
- phy->wkupclk = devm_clk_get(phy->dev, "usb_phy_cm_clk32k");
- if (IS_ERR(phy->wkupclk)) {
- dev_err(&pdev->dev, "unable to get usb_phy_cm_clk32k\n");
- return PTR_ERR(phy->wkupclk);
- }
- clk_prepare(phy->wkupclk);
-
- phy->optclk = devm_clk_get(phy->dev, "usb_otg_ss_refclk960m");
- if (IS_ERR(phy->optclk)) {
- dev_err(&pdev->dev, "unable to get usb_otg_ss_refclk960m\n");
- return PTR_ERR(phy->optclk);
- }
- clk_prepare(phy->optclk);
-
- phy->sys_clk = devm_clk_get(phy->dev, "sys_clkin");
- if (IS_ERR(phy->sys_clk)) {
- pr_err("%s: unable to get sys_clkin\n", __func__);
- return -EINVAL;
- }
-
- control_node = of_parse_phandle(node, "ctrl-module", 0);
- if (!control_node) {
- dev_err(&pdev->dev, "Failed to get control device phandle\n");
- return -EINVAL;
- }
- control_pdev = of_find_device_by_node(control_node);
- if (!control_pdev) {
- dev_err(&pdev->dev, "Failed to get control device\n");
- return -EINVAL;
- }
-
- phy->control_dev = &control_pdev->dev;
-
- omap_control_usb_phy_power(phy->control_dev, 0);
- usb_add_phy_dev(&phy->phy);
-
- platform_set_drvdata(pdev, phy);
-
- pm_runtime_enable(phy->dev);
- pm_runtime_get(&pdev->dev);
-
- return 0;
-}
-
-static int omap_usb3_remove(struct platform_device *pdev)
-{
- struct omap_usb *phy = platform_get_drvdata(pdev);
-
- clk_unprepare(phy->wkupclk);
- clk_unprepare(phy->optclk);
- usb_remove_phy(&phy->phy);
- if (!pm_runtime_suspended(&pdev->dev))
- pm_runtime_put(&pdev->dev);
- pm_runtime_disable(&pdev->dev);
-
- return 0;
-}
-
-#ifdef CONFIG_PM_RUNTIME
-
-static int omap_usb3_runtime_suspend(struct device *dev)
-{
- struct platform_device *pdev = to_platform_device(dev);
- struct omap_usb *phy = platform_get_drvdata(pdev);
-
- clk_disable(phy->wkupclk);
- clk_disable(phy->optclk);
-
- return 0;
-}
-
-static int omap_usb3_runtime_resume(struct device *dev)
-{
- u32 ret = 0;
- struct platform_device *pdev = to_platform_device(dev);
- struct omap_usb *phy = platform_get_drvdata(pdev);
-
- ret = clk_enable(phy->optclk);
- if (ret) {
- dev_err(phy->dev, "Failed to enable optclk %d\n", ret);
- goto err1;
- }
-
- ret = clk_enable(phy->wkupclk);
- if (ret) {
- dev_err(phy->dev, "Failed to enable wkupclk %d\n", ret);
- goto err2;
- }
-
- return 0;
-
-err2:
- clk_disable(phy->optclk);
-
-err1:
- return ret;
-}
-
-static const struct dev_pm_ops omap_usb3_pm_ops = {
- SET_RUNTIME_PM_OPS(omap_usb3_runtime_suspend, omap_usb3_runtime_resume,
- NULL)
-};
-
-#define DEV_PM_OPS (&omap_usb3_pm_ops)
-#else
-#define DEV_PM_OPS NULL
-#endif
-
-#ifdef CONFIG_OF
-static const struct of_device_id omap_usb3_id_table[] = {
- { .compatible = "ti,omap-usb3" },
- {}
-};
-MODULE_DEVICE_TABLE(of, omap_usb3_id_table);
-#endif
-
-static struct platform_driver omap_usb3_driver = {
- .probe = omap_usb3_probe,
- .remove = omap_usb3_remove,
- .driver = {
- .name = "omap-usb3",
- .owner = THIS_MODULE,
- .pm = DEV_PM_OPS,
- .of_match_table = of_match_ptr(omap_usb3_id_table),
- },
-};
-
-module_platform_driver(omap_usb3_driver);
-
-MODULE_ALIAS("platform: omap_usb3");
-MODULE_AUTHOR("Texas Instruments Inc.");
-MODULE_DESCRIPTION("OMAP USB3 phy driver");
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/usb/phy/phy-rcar-gen2-usb.c b/drivers/usb/phy/phy-rcar-gen2-usb.c
index 551e0a6c0e2..388d89f6b14 100644
--- a/drivers/usb/phy/phy-rcar-gen2-usb.c
+++ b/drivers/usb/phy/phy-rcar-gen2-usb.c
@@ -177,15 +177,15 @@ static int rcar_gen2_usb_phy_probe(struct platform_device *pdev)
struct clk *clk;
int retval;
- pdata = dev_get_platdata(&pdev->dev);
+ pdata = dev_get_platdata(dev);
if (!pdata) {
dev_err(dev, "No platform data\n");
return -EINVAL;
}
- clk = devm_clk_get(&pdev->dev, "usbhs");
+ clk = devm_clk_get(dev, "usbhs");
if (IS_ERR(clk)) {
- dev_err(&pdev->dev, "Can't get the clock\n");
+ dev_err(dev, "Can't get the clock\n");
return PTR_ERR(clk);
}
diff --git a/drivers/usb/phy/phy-twl6030-usb.c b/drivers/usb/phy/phy-twl6030-usb.c
index 214172b68d5..04778cf80d6 100644
--- a/drivers/usb/phy/phy-twl6030-usb.c
+++ b/drivers/usb/phy/phy-twl6030-usb.c
@@ -27,7 +27,7 @@
#include <linux/io.h>
#include <linux/usb/musb-omap.h>
#include <linux/usb/phy_companion.h>
-#include <linux/usb/omap_usb.h>
+#include <linux/phy/omap_usb.h>
#include <linux/i2c/twl.h>
#include <linux/regulator/consumer.h>
#include <linux/err.h>
diff --git a/drivers/usb/phy/phy-ulpi.c b/drivers/usb/phy/phy-ulpi.c
index 217339dd7a9..17ea3f271bd 100644
--- a/drivers/usb/phy/phy-ulpi.c
+++ b/drivers/usb/phy/phy-ulpi.c
@@ -47,6 +47,8 @@ struct ulpi_info {
static struct ulpi_info ulpi_ids[] = {
ULPI_INFO(ULPI_ID(0x04cc, 0x1504), "NXP ISP1504"),
ULPI_INFO(ULPI_ID(0x0424, 0x0006), "SMSC USB331x"),
+ ULPI_INFO(ULPI_ID(0x0424, 0x0007), "SMSC USB3320"),
+ ULPI_INFO(ULPI_ID(0x0451, 0x1507), "TI TUSB1210"),
};
static int ulpi_set_otg_flags(struct usb_phy *phy)
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-04 13:12:10 +0000