22 files changed, 914 insertions, 309 deletions

diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index 2b41c636a52..7d1451d5bbe 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -6,6 +6,15 @@ menu "USB Physical Layer drivers"
 config USB_PHY
 	def_bool n
 
+config USB_OTG_FSM
+	tristate "USB 2.0 OTG FSM implementation"
+	depends on USB
+	select USB_OTG
+	select USB_PHY
+	help
+	  Implements OTG Final State Machine as specified in On-The-Go
+	  and Embedded Host Supplement to the USB Revision 2.0 Specification.
+
 #
 # USB Transceiver Drivers
 #
@@ -19,9 +28,8 @@ config AB8500_USB
 	  in host mode, low speed.
 
 config FSL_USB2_OTG
-	tristate "Freescale USB OTG Transceiver Driver"
-	depends on USB_EHCI_FSL && USB_FSL_USB2 && PM_RUNTIME
-	depends on USB
+	bool "Freescale USB OTG Transceiver Driver"
+	depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM_RUNTIME
 	select USB_OTG
 	select USB_PHY
 	help
@@ -40,7 +48,16 @@ config ISP1301_OMAP
 	  Instruments OMAP processors.
 
 	  This driver can also be built as a module.  If so, the module
-	  will be called isp1301_omap.
+	  will be called phy-isp1301-omap.
+
+config KEYSTONE_USB_PHY
+	tristate "Keystone USB PHY Driver"
+	depends on ARCH_KEYSTONE || COMPILE_TEST
+	select NOP_USB_XCEIV
+	help
+	  Enable this to support Keystone USB phy. This driver provides
+	  interface to interact with USB 2.0 and USB 3.0 PHY that is part
+	  of the Keystone SOC.
 
 config MV_U3D_PHY
 	bool "Marvell USB 3.0 PHY controller Driver"
@@ -136,6 +153,31 @@ config USB_GPIO_VBUS
 	  optionally control of a D+ pullup GPIO as well as a VBUS
 	  current limit regulator.
 
+config OMAP_OTG
+	tristate "OMAP USB OTG controller driver"
+	depends on ARCH_OMAP_OTG && EXTCON
+	help
+	  Enable this to support some transceivers on OMAP1 platforms. OTG
+	  controller is needed to switch between host and peripheral modes.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called phy-omap-otg.
+
+config TAHVO_USB
+	tristate "Tahvo USB transceiver driver"
+	depends on MFD_RETU && EXTCON
+	select USB_PHY
+	help
+	  Enable this to support USB transceiver on Tahvo. This is used
+	  at least on Nokia 770.
+
+config TAHVO_USB_HOST_BY_DEFAULT
+	depends on TAHVO_USB
+	boolean "Device in USB host mode by default"
+	help
+	  Say Y here, if you want the device to enter USB host mode
+	  by default on bootup.
+
 config USB_ISP1301
 	tristate "NXP ISP1301 USB transceiver support"
 	depends on USB || USB_GADGET
@@ -147,7 +189,7 @@ config USB_ISP1301
 	  and OTG drivers (to be selected separately).
 
 	  To compile this driver as a module, choose M here: the
-	  module will be called isp1301.
+	  module will be called phy-isp1301.
 
 config USB_MSM_OTG
 	tristate "OTG support for Qualcomm on-chip USB controller"
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index 022c1da7fb7..be58adae349 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -3,18 +3,20 @@
 #
 obj-$(CONFIG_USB_PHY)			+= phy.o
 obj-$(CONFIG_OF)			+= of.o
+obj-$(CONFIG_USB_OTG_FSM)		+= phy-fsm-usb.o
 
 # transceiver drivers, keep the list sorted
 
 obj-$(CONFIG_AB8500_USB)		+= phy-ab8500-usb.o
-phy-fsl-usb2-objs			:= phy-fsl-usb.o phy-fsm-usb.o
-obj-$(CONFIG_FSL_USB2_OTG)		+= phy-fsl-usb2.o
+obj-$(CONFIG_FSL_USB2_OTG)		+= phy-fsl-usb.o
 obj-$(CONFIG_ISP1301_OMAP)		+= phy-isp1301-omap.o
 obj-$(CONFIG_MV_U3D_PHY)		+= phy-mv-u3d-usb.o
 obj-$(CONFIG_NOP_USB_XCEIV)		+= phy-generic.o
+obj-$(CONFIG_TAHVO_USB)			+= phy-tahvo.o
 obj-$(CONFIG_OMAP_CONTROL_USB)		+= phy-omap-control.o
 obj-$(CONFIG_AM335X_CONTROL_USB)	+= phy-am335x-control.o
 obj-$(CONFIG_AM335X_PHY_USB)		+= phy-am335x.o
+obj-$(CONFIG_OMAP_OTG)			+= phy-omap-otg.o
 obj-$(CONFIG_OMAP_USB3)			+= phy-omap-usb3.o
 obj-$(CONFIG_SAMSUNG_USBPHY)		+= phy-samsung-usb.o
 obj-$(CONFIG_SAMSUNG_USB2PHY)		+= phy-samsung-usb2.o
@@ -30,3 +32,4 @@ obj-$(CONFIG_USB_RCAR_PHY)		+= phy-rcar-usb.o
 obj-$(CONFIG_USB_RCAR_GEN2_PHY)		+= phy-rcar-gen2-usb.o
 obj-$(CONFIG_USB_ULPI)			+= phy-ulpi.o
 obj-$(CONFIG_USB_ULPI_VIEWPORT)		+= phy-ulpi-viewport.o
+obj-$(CONFIG_KEYSTONE_USB_PHY)		+= phy-keystone.o
diff --git a/drivers/usb/phy/phy-ab8500-usb.c b/drivers/usb/phy/phy-ab8500-usb.c
index 087402350b6..11ab2c45e46 100644
--- a/drivers/usb/phy/phy-ab8500-usb.c
+++ b/drivers/usb/phy/phy-ab8500-usb.c
@@ -1415,8 +1415,6 @@ static int ab8500_usb_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, ab);
 
-	ATOMIC_INIT_NOTIFIER_HEAD(&ab->phy.notifier);
-
 	/* all: Disable phy when called from set_host and set_peripheral */
 	INIT_WORK(&ab->phy_dis_work, ab8500_usb_phy_disable_work);
 
diff --git a/drivers/usb/phy/phy-am335x-control.c b/drivers/usb/phy/phy-am335x-control.c
index 634f49acd20..d75196ad5f2 100644
--- a/drivers/usb/phy/phy-am335x-control.c
+++ b/drivers/usb/phy/phy-am335x-control.c
@@ -3,11 +3,7 @@
 #include <linux/err.h>
 #include <linux/of.h>
 #include <linux/io.h>
-
-struct phy_control {
-	void (*phy_power)(struct phy_control *phy_ctrl, u32 id, bool on);
-	void (*phy_wkup)(struct phy_control *phy_ctrl, u32 id, bool on);
-};
+#include "am35x-phy-control.h"
 
 struct am335x_control_usb {
 	struct device *dev;
diff --git a/drivers/usb/phy/phy-am335x.c b/drivers/usb/phy/phy-am335x.c
index 0e3c60cb669..12fc3468a01 100644
--- a/drivers/usb/phy/phy-am335x.c
+++ b/drivers/usb/phy/phy-am335x.c
@@ -63,6 +63,19 @@ static int am335x_phy_probe(struct platform_device *pdev)
 	am_phy->usb_phy_gen.phy.shutdown = am335x_shutdown;
 
 	platform_set_drvdata(pdev, am_phy);
+	device_init_wakeup(dev, true);
+
+	/*
+	 * If we leave PHY wakeup enabled then AM33XX wakes up
+	 * immediately from DS0. To avoid this we mark dev->power.can_wakeup
+	 * to false. The same is checked in suspend routine to decide
+	 * on whether to enable PHY wakeup or not.
+	 * PHY wakeup works fine in standby mode, there by allowing us to
+	 * handle remote wakeup, wakeup on disconnect and connect.
+	 */
+
+	device_set_wakeup_enable(dev, false);
+	phy_ctrl_power(am_phy->phy_ctrl, am_phy->id, false);
 
 	return 0;
 }
@@ -75,38 +88,48 @@ static int am335x_phy_remove(struct platform_device *pdev)
 	return 0;
 }
 
-#ifdef CONFIG_PM_RUNTIME
-
-static int am335x_phy_runtime_suspend(struct device *dev)
+#ifdef CONFIG_PM_SLEEP
+static int am335x_phy_suspend(struct device *dev)
 {
 	struct platform_device	*pdev = to_platform_device(dev);
 	struct am335x_phy *am_phy = platform_get_drvdata(pdev);
 
+	/*
+	 * Enable phy wakeup only if dev->power.can_wakeup is true.
+	 * Make sure to enable wakeup to support remote wakeup	in
+	 * standby mode ( same is not supported in OFF(DS0) mode).
+	 * Enable it by doing
+	 * echo enabled > /sys/bus/platform/devices/<usb-phy-id>/power/wakeup
+	 */
+
 	if (device_may_wakeup(dev))
 		phy_ctrl_wkup(am_phy->phy_ctrl, am_phy->id, true);
+
 	phy_ctrl_power(am_phy->phy_ctrl, am_phy->id, false);
+
 	return 0;
 }
 
-static int am335x_phy_runtime_resume(struct device *dev)
+static int am335x_phy_resume(struct device *dev)
 {
 	struct platform_device	*pdev = to_platform_device(dev);
 	struct am335x_phy	*am_phy = platform_get_drvdata(pdev);
 
 	phy_ctrl_power(am_phy->phy_ctrl, am_phy->id, true);
+
 	if (device_may_wakeup(dev))
 		phy_ctrl_wkup(am_phy->phy_ctrl, am_phy->id, false);
+
 	return 0;
 }
 
 static const struct dev_pm_ops am335x_pm_ops = {
-	SET_RUNTIME_PM_OPS(am335x_phy_runtime_suspend,
-			am335x_phy_runtime_resume, NULL)
+	SET_SYSTEM_SLEEP_PM_OPS(am335x_phy_suspend, am335x_phy_resume)
 };
 
-#define DEV_PM_OPS	(&am335x_pm_ops)
+#define DEV_PM_OPS     (&am335x_pm_ops)
 #else
-#define DEV_PM_OPS	NULL
+#define DEV_PM_OPS     NULL
 #endif
 
 static const struct of_device_id am335x_phy_ids[] = {
diff --git a/drivers/usb/phy/phy-fsl-usb.c b/drivers/usb/phy/phy-fsl-usb.c
index 7f3c73b967c..2b0f968d932 100644
--- a/drivers/usb/phy/phy-fsl-usb.c
+++ b/drivers/usb/phy/phy-fsl-usb.c
@@ -27,7 +27,6 @@
 #include <linux/slab.h>
 #include <linux/proc_fs.h>
 #include <linux/errno.h>
-#include <linux/init.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/timer.h>
@@ -848,7 +847,7 @@ static int fsl_otg_conf(struct platform_device *pdev)
 		pr_info("Couldn't init OTG timers\n");
 		goto err;
 	}
-	spin_lock_init(&fsl_otg_tc->fsm.lock);
+	mutex_init(&fsl_otg_tc->fsm.lock);
 
 	/* Set OTG state machine operations */
 	fsl_otg_tc->fsm.ops = &fsl_otg_ops;
@@ -1017,10 +1016,9 @@ static int show_fsl_usb2_otg_state(struct device *dev,
 	struct otg_fsm *fsm = &fsl_otg_dev->fsm;
 	char *next = buf;
 	unsigned size = PAGE_SIZE;
-	unsigned long flags;
 	int t;
 
-	spin_lock_irqsave(&fsm->lock, flags);
+	mutex_lock(&fsm->lock);
 
 	/* basic driver infomation */
 	t = scnprintf(next, size,
@@ -1088,7 +1086,7 @@ static int show_fsl_usb2_otg_state(struct device *dev,
 	size -= t;
 	next += t;
 
-	spin_unlock_irqrestore(&fsm->lock, flags);
+	mutex_unlock(&fsm->lock);
 
 	return PAGE_SIZE - size;
 }
diff --git a/drivers/usb/phy/phy-fsl-usb.h b/drivers/usb/phy/phy-fsl-usb.h
index 7365170a2f2..5986c96354d 100644
--- a/drivers/usb/phy/phy-fsl-usb.h
+++ b/drivers/usb/phy/phy-fsl-usb.h
@@ -15,7 +15,7 @@
  * 675 Mass Ave, Cambridge, MA 02139, USA.
  */
 
-#include "phy-fsm-usb.h"
+#include <linux/usb/otg-fsm.h>
 #include <linux/usb/otg.h>
 #include <linux/ioctl.h>
 
diff --git a/drivers/usb/phy/phy-fsm-usb.c b/drivers/usb/phy/phy-fsm-usb.c
index 329c2d2f859..7aa314ef4a8 100644
--- a/drivers/usb/phy/phy-fsm-usb.c
+++ b/drivers/usb/phy/phy-fsm-usb.c
@@ -23,13 +23,12 @@
 
 #include <linux/kernel.h>
 #include <linux/types.h>
-#include <linux/spinlock.h>
+#include <linux/mutex.h>
 #include <linux/delay.h>
 #include <linux/usb.h>
 #include <linux/usb/gadget.h>
 #include <linux/usb/otg.h>
-
-#include "phy-fsm-usb.h"
+#include <linux/usb/otg-fsm.h>
 
 /* Change USB protocol when there is a protocol change */
 static int otg_set_protocol(struct otg_fsm *fsm, int protocol)
@@ -65,7 +64,7 @@ static int otg_set_protocol(struct otg_fsm *fsm, int protocol)
 static int state_changed;
 
 /* Called when leaving a state.  Do state clean up jobs here */
-void otg_leave_state(struct otg_fsm *fsm, enum usb_otg_state old_state)
+static void otg_leave_state(struct otg_fsm *fsm, enum usb_otg_state old_state)
 {
 	switch (old_state) {
 	case OTG_STATE_B_IDLE:
@@ -122,7 +121,7 @@ void otg_leave_state(struct otg_fsm *fsm, enum usb_otg_state old_state)
 }
 
 /* Called when entering a state */
-int otg_set_state(struct otg_fsm *fsm, enum usb_otg_state new_state)
+static int otg_set_state(struct otg_fsm *fsm, enum usb_otg_state new_state)
 {
 	state_changed = 1;
 	if (fsm->otg->phy->state == new_state)
@@ -245,9 +244,8 @@ int otg_set_state(struct otg_fsm *fsm, enum usb_otg_state new_state)
 int otg_statemachine(struct otg_fsm *fsm)
 {
 	enum usb_otg_state state;
-	unsigned long flags;
 
-	spin_lock_irqsave(&fsm->lock, flags);
+	mutex_lock(&fsm->lock);
 
 	state = fsm->otg->phy->state;
 	state_changed = 0;
@@ -359,7 +357,7 @@ int otg_statemachine(struct otg_fsm *fsm)
 	default:
 		break;
 	}
-	spin_unlock_irqrestore(&fsm->lock, flags);
+	mutex_unlock(&fsm->lock);
 
 	VDBG("quit statemachine, changed = %d\n", state_changed);
 	return state_changed;
diff --git a/drivers/usb/phy/phy-fsm-usb.h b/drivers/usb/phy/phy-fsm-usb.h
deleted file mode 100644
index 7441b46a27f..00000000000
--- a/drivers/usb/phy/phy-fsm-usb.h
+++ /dev/null
@@ -1,236 +0,0 @@
-/* Copyright (C) 2007,2008 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the  GNU General Public License along
- * with this program; if not, write  to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#undef VERBOSE
-
-#ifdef VERBOSE
-#define VDBG(fmt, args...) pr_debug("[%s]  " fmt , \
-				 __func__, ## args)
-#else
-#define VDBG(stuff...)	do {} while (0)
-#endif
-
-#ifdef VERBOSE
-#define MPC_LOC printk("Current Location [%s]:[%d]\n", __FILE__, __LINE__)
-#else
-#define MPC_LOC do {} while (0)
-#endif
-
-#define PROTO_UNDEF	(0)
-#define PROTO_HOST	(1)
-#define PROTO_GADGET	(2)
-
-enum otg_fsm_timer {
-	/* Standard OTG timers */
-	A_WAIT_VRISE,
-	A_WAIT_VFALL,
-	A_WAIT_BCON,
-	A_AIDL_BDIS,
-	B_ASE0_BRST,
-	A_BIDL_ADIS,
-
-	/* Auxiliary timers */
-	B_SE0_SRP,
-	B_SRP_FAIL,
-	A_WAIT_ENUM,
-
-	NUM_OTG_FSM_TIMERS,
-};
-
-/* OTG state machine according to the OTG spec */
-struct otg_fsm {
-	/* Input */
-	int id;
-	int adp_change;
-	int power_up;
-	int test_device;
-	int a_bus_drop;
-	int a_bus_req;
-	int a_srp_det;
-	int a_vbus_vld;
-	int b_conn;
-	int a_bus_resume;
-	int a_bus_suspend;
-	int a_conn;
-	int b_bus_req;
-	int b_se0_srp;
-	int b_ssend_srp;
-	int b_sess_vld;
-	/* Auxilary inputs */
-	int a_sess_vld;
-	int b_bus_resume;
-	int b_bus_suspend;
-
-	/* Output */
-	int data_pulse;
-	int drv_vbus;
-	int loc_conn;
-	int loc_sof;
-	int adp_prb;
-	int adp_sns;
-
-	/* Internal variables */
-	int a_set_b_hnp_en;
-	int b_srp_done;
-	int b_hnp_enable;
-	int a_clr_err;
-
-	/* Informative variables */
-	int a_bus_drop_inf;
-	int a_bus_req_inf;
-	int a_clr_err_inf;
-	int b_bus_req_inf;
-	/* Auxilary informative variables */
-	int a_suspend_req_inf;
-
-	/* Timeout indicator for timers */
-	int a_wait_vrise_tmout;
-	int a_wait_vfall_tmout;
-	int a_wait_bcon_tmout;
-	int a_aidl_bdis_tmout;
-	int b_ase0_brst_tmout;
-	int a_bidl_adis_tmout;
-
-	struct otg_fsm_ops *ops;
-	struct usb_otg *otg;
-
-	/* Current usb protocol used: 0:undefine; 1:host; 2:client */
-	int protocol;
-	spinlock_t lock;
-};
-
-struct otg_fsm_ops {
-	void	(*chrg_vbus)(struct otg_fsm *fsm, int on);
-	void	(*drv_vbus)(struct otg_fsm *fsm, int on);
-	void	(*loc_conn)(struct otg_fsm *fsm, int on);
-	void	(*loc_sof)(struct otg_fsm *fsm, int on);
-	void	(*start_pulse)(struct otg_fsm *fsm);
-	void	(*start_adp_prb)(struct otg_fsm *fsm);
-	void	(*start_adp_sns)(struct otg_fsm *fsm);
-	void	(*add_timer)(struct otg_fsm *fsm, enum otg_fsm_timer timer);
-	void	(*del_timer)(struct otg_fsm *fsm, enum otg_fsm_timer timer);
-	int	(*start_host)(struct otg_fsm *fsm, int on);
-	int	(*start_gadget)(struct otg_fsm *fsm, int on);
-};
-
-
-static inline int otg_chrg_vbus(struct otg_fsm *fsm, int on)
-{
-	if (!fsm->ops->chrg_vbus)
-		return -EOPNOTSUPP;
-	fsm->ops->chrg_vbus(fsm, on);
-	return 0;
-}
-
-static inline int otg_drv_vbus(struct otg_fsm *fsm, int on)
-{
-	if (!fsm->ops->drv_vbus)
-		return -EOPNOTSUPP;
-	if (fsm->drv_vbus != on) {
-		fsm->drv_vbus = on;
-		fsm->ops->drv_vbus(fsm, on);
-	}
-	return 0;
-}
-
-static inline int otg_loc_conn(struct otg_fsm *fsm, int on)
-{
-	if (!fsm->ops->loc_conn)
-		return -EOPNOTSUPP;
-	if (fsm->loc_conn != on) {
-		fsm->loc_conn = on;
-		fsm->ops->loc_conn(fsm, on);
-	}
-	return 0;
-}
-
-static inline int otg_loc_sof(struct otg_fsm *fsm, int on)
-{
-	if (!fsm->ops->loc_sof)
-		return -EOPNOTSUPP;
-	if (fsm->loc_sof != on) {
-		fsm->loc_sof = on;
-		fsm->ops->loc_sof(fsm, on);
-	}
-	return 0;
-}
-
-static inline int otg_start_pulse(struct otg_fsm *fsm)
-{
-	if (!fsm->ops->start_pulse)
-		return -EOPNOTSUPP;
-	if (!fsm->data_pulse) {
-		fsm->data_pulse = 1;
-		fsm->ops->start_pulse(fsm);
-	}
-	return 0;
-}
-
-static inline int otg_start_adp_prb(struct otg_fsm *fsm)
-{
-	if (!fsm->ops->start_adp_prb)
-		return -EOPNOTSUPP;
-	if (!fsm->adp_prb) {
-		fsm->adp_sns = 0;
-		fsm->adp_prb = 1;
-		fsm->ops->start_adp_prb(fsm);
-	}
-	return 0;
-}
-
-static inline int otg_start_adp_sns(struct otg_fsm *fsm)
-{
-	if (!fsm->ops->start_adp_sns)
-		return -EOPNOTSUPP;
-	if (!fsm->adp_sns) {
-		fsm->adp_sns = 1;
-		fsm->ops->start_adp_sns(fsm);
-	}
-	return 0;
-}
-
-static inline int otg_add_timer(struct otg_fsm *fsm, enum otg_fsm_timer timer)
-{
-	if (!fsm->ops->add_timer)
-		return -EOPNOTSUPP;
-	fsm->ops->add_timer(fsm, timer);
-	return 0;
-}
-
-static inline int otg_del_timer(struct otg_fsm *fsm, enum otg_fsm_timer timer)
-{
-	if (!fsm->ops->del_timer)
-		return -EOPNOTSUPP;
-	fsm->ops->del_timer(fsm, timer);
-	return 0;
-}
-
-static inline int otg_start_host(struct otg_fsm *fsm, int on)
-{
-	if (!fsm->ops->start_host)
-		return -EOPNOTSUPP;
-	return fsm->ops->start_host(fsm, on);
-}
-
-static inline int otg_start_gadget(struct otg_fsm *fsm, int on)
-{
-	if (!fsm->ops->start_gadget)
-		return -EOPNOTSUPP;
-	return fsm->ops->start_gadget(fsm, on);
-}
-
-int otg_statemachine(struct otg_fsm *fsm);
diff --git a/drivers/usb/phy/phy-generic.c b/drivers/usb/phy/phy-generic.c
index aa6d37b3378..bb394980532 100644
--- a/drivers/usb/phy/phy-generic.c
+++ b/drivers/usb/phy/phy-generic.c
@@ -241,7 +241,6 @@ int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_gen_xceiv *nop,
 	nop->phy.otg->set_host		= nop_set_host;
 	nop->phy.otg->set_peripheral	= nop_set_peripheral;
 
-	ATOMIC_INIT_NOTIFIER_HEAD(&nop->phy.notifier);
 	return 0;
 }
 EXPORT_SYMBOL_GPL(usb_phy_gen_create_phy);
diff --git a/drivers/usb/phy/phy-gpio-vbus-usb.c b/drivers/usb/phy/phy-gpio-vbus-usb.c
index 02799a5efcd..69462e09d01 100644
--- a/drivers/usb/phy/phy-gpio-vbus-usb.c
+++ b/drivers/usb/phy/phy-gpio-vbus-usb.c
@@ -314,8 +314,6 @@ static int gpio_vbus_probe(struct platform_device *pdev)
 		goto err_irq;
 	}
 
-	ATOMIC_INIT_NOTIFIER_HEAD(&gpio_vbus->phy.notifier);
-
 	INIT_DELAYED_WORK(&gpio_vbus->work, gpio_vbus_work);
 
 	gpio_vbus->vbus_draw = regulator_get(&pdev->dev, "vbus_draw");
diff --git a/drivers/usb/phy/phy-isp1301-omap.c b/drivers/usb/phy/phy-isp1301-omap.c
index d3a5160e4cc..6e146d723b3 100644
--- a/drivers/usb/phy/phy-isp1301-omap.c
+++ b/drivers/usb/phy/phy-isp1301-omap.c
@@ -1277,7 +1277,7 @@ isp1301_set_host(struct usb_otg *otg, struct usb_bus *host)
 {
 	struct isp1301	*isp = container_of(otg->phy, struct isp1301, phy);
 
-	if (!otg || isp != the_transceiver)
+	if (isp != the_transceiver)
 		return -ENODEV;
 
 	if (!host) {
@@ -1333,7 +1333,7 @@ isp1301_set_peripheral(struct usb_otg *otg, struct usb_gadget *gadget)
 {
 	struct isp1301	*isp = container_of(otg->phy, struct isp1301, phy);
 
-	if (!otg || isp != the_transceiver)
+	if (isp != the_transceiver)
 		return -ENODEV;
 
 	if (!gadget) {
@@ -1414,8 +1414,7 @@ isp1301_start_srp(struct usb_otg *otg)
 	struct isp1301	*isp = container_of(otg->phy, struct isp1301, phy);
 	u32		otg_ctrl;
 
-	if (!otg || isp != the_transceiver
-			|| isp->phy.state != OTG_STATE_B_IDLE)
+	if (isp != the_transceiver || isp->phy.state != OTG_STATE_B_IDLE)
 		return -ENODEV;
 
 	otg_ctrl = omap_readl(OTG_CTRL);
@@ -1442,7 +1441,7 @@ isp1301_start_hnp(struct usb_otg *otg)
 	struct isp1301	*isp = container_of(otg->phy, struct isp1301, phy);
 	u32 l;
 
-	if (!otg || isp != the_transceiver)
+	if (isp != the_transceiver)
 		return -ENODEV;
 	if (otg->default_a && (otg->host == NULL || !otg->host->b_hnp_enable))
 		return -ENOTCONN;
diff --git a/drivers/usb/phy/phy-keystone.c b/drivers/usb/phy/phy-keystone.c
new file mode 100644
index 00000000000..d762003896c
--- /dev/null
+++ b/drivers/usb/phy/phy-keystone.c
@@ -0,0 +1,136 @@
+/*
+ * phy-keystone - USB PHY, talking to dwc3 controller in Keystone.
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: WingMan Kwok <w-kwok2@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/usb/usb_phy_gen_xceiv.h>
+#include <linux/io.h>
+#include <linux/of.h>
+
+#include "phy-generic.h"
+
+/* USB PHY control register offsets */
+#define USB_PHY_CTL_UTMI		0x0000
+#define USB_PHY_CTL_PIPE		0x0004
+#define USB_PHY_CTL_PARAM_1		0x0008
+#define USB_PHY_CTL_PARAM_2		0x000c
+#define USB_PHY_CTL_CLOCK		0x0010
+#define USB_PHY_CTL_PLL			0x0014
+
+#define PHY_REF_SSP_EN			BIT(29)
+
+struct keystone_usbphy {
+	struct usb_phy_gen_xceiv	usb_phy_gen;
+	void __iomem			*phy_ctrl;
+};
+
+static inline u32 keystone_usbphy_readl(void __iomem *base, u32 offset)
+{
+	return readl(base + offset);
+}
+
+static inline void keystone_usbphy_writel(void __iomem *base,
+					  u32 offset, u32 value)
+{
+	writel(value, base + offset);
+}
+
+static int keystone_usbphy_init(struct usb_phy *phy)
+{
+	struct keystone_usbphy *k_phy = dev_get_drvdata(phy->dev);
+	u32 val;
+
+	val  = keystone_usbphy_readl(k_phy->phy_ctrl, USB_PHY_CTL_CLOCK);
+	keystone_usbphy_writel(k_phy->phy_ctrl, USB_PHY_CTL_CLOCK,
+				val | PHY_REF_SSP_EN);
+	return 0;
+}
+
+static void keystone_usbphy_shutdown(struct usb_phy *phy)
+{
+	struct keystone_usbphy *k_phy = dev_get_drvdata(phy->dev);
+	u32 val;
+
+	val  = keystone_usbphy_readl(k_phy->phy_ctrl, USB_PHY_CTL_CLOCK);
+	keystone_usbphy_writel(k_phy->phy_ctrl, USB_PHY_CTL_CLOCK,
+				val &= ~PHY_REF_SSP_EN);
+}
+
+static int keystone_usbphy_probe(struct platform_device *pdev)
+{
+	struct device		*dev = &pdev->dev;
+	struct keystone_usbphy	*k_phy;
+	struct resource		*res;
+	int ret;
+
+	k_phy = devm_kzalloc(dev, sizeof(*k_phy), GFP_KERNEL);
+	if (!k_phy)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	k_phy->phy_ctrl = devm_ioremap_resource(dev, res);
+	if (IS_ERR(k_phy->phy_ctrl))
+		return PTR_ERR(k_phy->phy_ctrl);
+
+	ret = usb_phy_gen_create_phy(dev, &k_phy->usb_phy_gen, NULL);
+	if (ret)
+		return ret;
+
+	k_phy->usb_phy_gen.phy.init = keystone_usbphy_init;
+	k_phy->usb_phy_gen.phy.shutdown = keystone_usbphy_shutdown;
+
+	platform_set_drvdata(pdev, k_phy);
+
+	ret = usb_add_phy_dev(&k_phy->usb_phy_gen.phy);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int keystone_usbphy_remove(struct platform_device *pdev)
+{
+	struct keystone_usbphy *k_phy = platform_get_drvdata(pdev);
+
+	usb_remove_phy(&k_phy->usb_phy_gen.phy);
+
+	return 0;
+}
+
+static const struct of_device_id keystone_usbphy_ids[] = {
+	{ .compatible = "ti,keystone-usbphy" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, keystone_usbphy_ids);
+
+static struct platform_driver keystone_usbphy_driver = {
+	.probe          = keystone_usbphy_probe,
+	.remove         = keystone_usbphy_remove,
+	.driver         = {
+		.name   = "keystone-usbphy",
+		.owner  = THIS_MODULE,
+		.of_match_table = keystone_usbphy_ids,
+	},
+};
+
+module_platform_driver(keystone_usbphy_driver);
+
+MODULE_ALIAS("platform:keystone-usbphy");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_DESCRIPTION("Keystone USB phy driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/usb/phy/phy-msm-usb.c b/drivers/usb/phy/phy-msm-usb.c
index e9d4cd960ec..8546c8dccd5 100644
--- a/drivers/usb/phy/phy-msm-usb.c
+++ b/drivers/usb/phy/phy-msm-usb.c
@@ -40,8 +40,6 @@
 #include <linux/usb/msm_hsusb_hw.h>
 #include <linux/regulator/consumer.h>
 
-#include <mach/clk.h>
-
 #define MSM_USB_BASE	(motg->regs)
 #define DRIVER_NAME	"msm_otg"
 
@@ -308,33 +306,30 @@ static void ulpi_init(struct msm_otg *motg)
 
 static int msm_otg_link_clk_reset(struct msm_otg *motg, bool assert)
 {
-	int ret;
+	int ret = 0;
+
+	if (!motg->pdata->link_clk_reset)
+		return ret;
+
+	ret = motg->pdata->link_clk_reset(motg->clk, assert);
+	if (ret)
+		dev_err(motg->phy.dev, "usb link clk reset %s failed\n",
+			assert ? "assert" : "deassert");
 
-	if (assert) {
-		ret = clk_reset(motg->clk, CLK_RESET_ASSERT);
-		if (ret)
-			dev_err(motg->phy.dev, "usb hs_clk assert failed\n");
-	} else {
-		ret = clk_reset(motg->clk, CLK_RESET_DEASSERT);
-		if (ret)
-			dev_err(motg->phy.dev, "usb hs_clk deassert failed\n");
-	}
 	return ret;
 }
 
 static int msm_otg_phy_clk_reset(struct msm_otg *motg)
 {
-	int ret;
+	int ret = 0;
 
-	ret = clk_reset(motg->phy_reset_clk, CLK_RESET_ASSERT);
-	if (ret) {
-		dev_err(motg->phy.dev, "usb phy clk assert failed\n");
+	if (!motg->pdata->phy_clk_reset)
 		return ret;
-	}
-	usleep_range(10000, 12000);
-	ret = clk_reset(motg->phy_reset_clk, CLK_RESET_DEASSERT);
+
+	ret = motg->pdata->phy_clk_reset(motg->phy_reset_clk);
 	if (ret)
-		dev_err(motg->phy.dev, "usb phy clk deassert failed\n");
+		dev_err(motg->phy.dev, "usb phy clk reset failed\n");
+
 	return ret;
 }
 
@@ -669,6 +664,7 @@ static void msm_otg_start_host(struct usb_phy *phy, int on)
 			pdata->setup_gpio(OTG_STATE_A_HOST);
 #ifdef CONFIG_USB
 		usb_add_hcd(hcd, hcd->irq, IRQF_SHARED);
+		device_wakeup_enable(hcd->self.controller);
 #endif
 	} else {
 		dev_dbg(phy->dev, "host off\n");
diff --git a/drivers/usb/phy/phy-mv-usb.c b/drivers/usb/phy/phy-mv-usb.c
index 98f6ac6a78e..7d80c54f0ac 100644
--- a/drivers/usb/phy/phy-mv-usb.c
+++ b/drivers/usb/phy/phy-mv-usb.c
@@ -11,7 +11,6 @@
 
 #include <linux/module.h>
 #include <linux/kernel.h>
-#include <linux/init.h>
 #include <linux/io.h>
 #include <linux/uaccess.h>
 #include <linux/device.h>
@@ -213,10 +212,12 @@ static void mv_otg_start_host(struct mv_otg *mvotg, int on)
 
 	hcd = bus_to_hcd(otg->host);
 
-	if (on)
+	if (on) {
 		usb_add_hcd(hcd, hcd->irq, IRQF_SHARED);
-	else
+		device_wakeup_enable(hcd->self.controller);
+	} else {
 		usb_remove_hcd(hcd);
+	}
 #endif /* CONFIG_USB */
 }
 
diff --git a/drivers/usb/phy/phy-mxs-usb.c b/drivers/usb/phy/phy-mxs-usb.c
index 545844b7e79..b42897b6474 100644
--- a/drivers/usb/phy/phy-mxs-usb.c
+++ b/drivers/usb/phy/phy-mxs-usb.c
@@ -63,9 +63,13 @@ static int mxs_phy_hw_init(struct mxs_phy *mxs_phy)
 
 static int mxs_phy_init(struct usb_phy *phy)
 {
+	int ret;
 	struct mxs_phy *mxs_phy = to_mxs_phy(phy);
 
-	clk_prepare_enable(mxs_phy->clk);
+	ret = clk_prepare_enable(mxs_phy->clk);
+	if (ret)
+		return ret;
+
 	return mxs_phy_hw_init(mxs_phy);
 }
 
@@ -81,6 +85,7 @@ static void mxs_phy_shutdown(struct usb_phy *phy)
 
 static int mxs_phy_suspend(struct usb_phy *x, int suspend)
 {
+	int ret;
 	struct mxs_phy *mxs_phy = to_mxs_phy(x);
 
 	if (suspend) {
@@ -89,7 +94,9 @@ static int mxs_phy_suspend(struct usb_phy *x, int suspend)
 		       x->io_priv + HW_USBPHY_CTRL_SET);
 		clk_disable_unprepare(mxs_phy->clk);
 	} else {
-		clk_prepare_enable(mxs_phy->clk);
+		ret = clk_prepare_enable(mxs_phy->clk);
+		if (ret)
+			return ret;
 		writel(BM_USBPHY_CTRL_CLKGATE,
 		       x->io_priv + HW_USBPHY_CTRL_CLR);
 		writel(0, x->io_priv + HW_USBPHY_PWD);
@@ -160,8 +167,6 @@ static int mxs_phy_probe(struct platform_device *pdev)
 	mxs_phy->phy.notify_disconnect	= mxs_phy_on_disconnect;
 	mxs_phy->phy.type		= USB_PHY_TYPE_USB2;
 
-	ATOMIC_INIT_NOTIFIER_HEAD(&mxs_phy->phy.notifier);
-
 	mxs_phy->clk = clk;
 
 	platform_set_drvdata(pdev, mxs_phy);
diff --git a/drivers/usb/phy/phy-omap-control.c b/drivers/usb/phy/phy-omap-control.c
index 09c5ace1edd..e7253182e47 100644
--- a/drivers/usb/phy/phy-omap-control.c
+++ b/drivers/usb/phy/phy-omap-control.c
@@ -84,6 +84,20 @@ void omap_control_usb_phy_power(struct device *dev, int on)
 		else
 			val |= OMAP_CTRL_USB2_PHY_PD;
 		break;
+
+	case OMAP_CTRL_TYPE_AM437USB2:
+		if (on) {
+			val &= ~(AM437X_CTRL_USB2_PHY_PD |
+					AM437X_CTRL_USB2_OTG_PD);
+			val |= (AM437X_CTRL_USB2_OTGVDET_EN |
+					AM437X_CTRL_USB2_OTGSESSEND_EN);
+		} else {
+			val &= ~(AM437X_CTRL_USB2_OTGVDET_EN |
+					AM437X_CTRL_USB2_OTGSESSEND_EN);
+			val |= (AM437X_CTRL_USB2_PHY_PD |
+					 AM437X_CTRL_USB2_OTG_PD);
+		}
+		break;
 	default:
 		dev_err(dev, "%s: type %d not recognized\n",
 					__func__, control_usb->type);
@@ -197,6 +211,7 @@ static const enum omap_control_usb_type otghs_data = OMAP_CTRL_TYPE_OTGHS;
 static const enum omap_control_usb_type usb2_data = OMAP_CTRL_TYPE_USB2;
 static const enum omap_control_usb_type pipe3_data = OMAP_CTRL_TYPE_PIPE3;
 static const enum omap_control_usb_type dra7usb2_data = OMAP_CTRL_TYPE_DRA7USB2;
+static const enum omap_control_usb_type am437usb2_data = OMAP_CTRL_TYPE_AM437USB2;
 
 static const struct of_device_id omap_control_usb_id_table[] = {
 	{
@@ -215,6 +230,10 @@ static const struct of_device_id omap_control_usb_id_table[] = {
 		.compatible = "ti,control-phy-dra7usb2",
 		.data = &dra7usb2_data,
 	},
+	{
+		.compatible = "ti,control-phy-am437usb2",
+		.data = &am437usb2_data,
+	},
 	{},
 };
 MODULE_DEVICE_TABLE(of, omap_control_usb_id_table);
diff --git a/drivers/usb/phy/phy-omap-otg.c b/drivers/usb/phy/phy-omap-otg.c
new file mode 100644
index 00000000000..11598cdb318
--- /dev/null
+++ b/drivers/usb/phy/phy-omap-otg.c
@@ -0,0 +1,169 @@
+/*
+ * OMAP OTG controller driver
+ *
+ * Based on code from tahvo-usb.c and isp1301_omap.c drivers.
+ *
+ * Copyright (C) 2005-2006 Nokia Corporation
+ * Copyright (C) 2004 Texas Instruments
+ * Copyright (C) 2004 David Brownell
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/err.h>
+#include <linux/extcon.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/usb-omap1.h>
+
+struct otg_device {
+	void __iomem			*base;
+	bool				id;
+	bool				vbus;
+	struct extcon_specific_cable_nb	vbus_dev;
+	struct extcon_specific_cable_nb	id_dev;
+	struct notifier_block		vbus_nb;
+	struct notifier_block		id_nb;
+};
+
+#define OMAP_OTG_CTRL		0x0c
+#define OMAP_OTG_ASESSVLD	(1 << 20)
+#define OMAP_OTG_BSESSEND	(1 << 19)
+#define OMAP_OTG_BSESSVLD	(1 << 18)
+#define OMAP_OTG_VBUSVLD	(1 << 17)
+#define OMAP_OTG_ID		(1 << 16)
+#define OMAP_OTG_XCEIV_OUTPUTS \
+	(OMAP_OTG_ASESSVLD | OMAP_OTG_BSESSEND | OMAP_OTG_BSESSVLD | \
+	 OMAP_OTG_VBUSVLD  | OMAP_OTG_ID)
+
+static void omap_otg_ctrl(struct otg_device *otg_dev, u32 outputs)
+{
+	u32 l;
+
+	l = readl(otg_dev->base + OMAP_OTG_CTRL);
+	l &= ~OMAP_OTG_XCEIV_OUTPUTS;
+	l |= outputs;
+	writel(l, otg_dev->base + OMAP_OTG_CTRL);
+}
+
+static void omap_otg_set_mode(struct otg_device *otg_dev)
+{
+	if (!otg_dev->id && otg_dev->vbus)
+		/* Set B-session valid. */
+		omap_otg_ctrl(otg_dev, OMAP_OTG_ID | OMAP_OTG_BSESSVLD);
+	else if (otg_dev->vbus)
+		/* Set A-session valid. */
+		omap_otg_ctrl(otg_dev, OMAP_OTG_ASESSVLD);
+	else if (!otg_dev->id)
+		/* Set B-session end to indicate no VBUS. */
+		omap_otg_ctrl(otg_dev, OMAP_OTG_ID | OMAP_OTG_BSESSEND);
+}
+
+static int omap_otg_id_notifier(struct notifier_block *nb,
+				unsigned long event, void *ptr)
+{
+	struct otg_device *otg_dev = container_of(nb, struct otg_device, id_nb);
+
+	otg_dev->id = event;
+	omap_otg_set_mode(otg_dev);
+
+	return NOTIFY_DONE;
+}
+
+static int omap_otg_vbus_notifier(struct notifier_block *nb,
+				  unsigned long event, void *ptr)
+{
+	struct otg_device *otg_dev = container_of(nb, struct otg_device,
+						  vbus_nb);
+
+	otg_dev->vbus = event;
+	omap_otg_set_mode(otg_dev);
+
+	return NOTIFY_DONE;
+}
+
+static int omap_otg_probe(struct platform_device *pdev)
+{
+	const struct omap_usb_config *config = pdev->dev.platform_data;
+	struct otg_device *otg_dev;
+	struct extcon_dev *extcon;
+	int ret;
+	u32 rev;
+
+	if (!config || !config->extcon)
+		return -ENODEV;
+
+	extcon = extcon_get_extcon_dev(config->extcon);
+	if (!extcon)
+		return -EPROBE_DEFER;
+
+	otg_dev = devm_kzalloc(&pdev->dev, sizeof(*otg_dev), GFP_KERNEL);
+	if (!otg_dev)
+		return -ENOMEM;
+
+	otg_dev->base = devm_ioremap_resource(&pdev->dev, &pdev->resource[0]);
+	if (IS_ERR(otg_dev->base))
+		return PTR_ERR(otg_dev->base);
+
+	otg_dev->id_nb.notifier_call = omap_otg_id_notifier;
+	otg_dev->vbus_nb.notifier_call = omap_otg_vbus_notifier;
+
+	ret = extcon_register_interest(&otg_dev->id_dev, config->extcon,
+				       "USB-HOST", &otg_dev->id_nb);
+	if (ret)
+		return ret;
+
+	ret = extcon_register_interest(&otg_dev->vbus_dev, config->extcon,
+				       "USB", &otg_dev->vbus_nb);
+	if (ret) {
+		extcon_unregister_interest(&otg_dev->id_dev);
+		return ret;
+	}
+
+	otg_dev->id = extcon_get_cable_state(extcon, "USB-HOST");
+	otg_dev->vbus = extcon_get_cable_state(extcon, "USB");
+	omap_otg_set_mode(otg_dev);
+
+	rev = readl(otg_dev->base);
+
+	dev_info(&pdev->dev,
+		 "OMAP USB OTG controller rev %d.%d (%s, id=%d, vbus=%d)\n",
+		 (rev >> 4) & 0xf, rev & 0xf, config->extcon, otg_dev->id,
+		 otg_dev->vbus);
+
+	return 0;
+}
+
+static int omap_otg_remove(struct platform_device *pdev)
+{
+	struct otg_device *otg_dev = platform_get_drvdata(pdev);
+
+	extcon_unregister_interest(&otg_dev->id_dev);
+	extcon_unregister_interest(&otg_dev->vbus_dev);
+
+	return 0;
+}
+
+static struct platform_driver omap_otg_driver = {
+	.probe		= omap_otg_probe,
+	.remove		= omap_otg_remove,
+	.driver		= {
+		.owner	= THIS_MODULE,
+		.name	= "omap_otg",
+	},
+};
+module_platform_driver(omap_otg_driver);
+
+MODULE_DESCRIPTION("OMAP USB OTG controller driver");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Aaro Koskinen <aaro.koskinen@iki.fi>");
diff --git a/drivers/usb/phy/phy-rcar-gen2-usb.c b/drivers/usb/phy/phy-rcar-gen2-usb.c
index db3ab34cddb..551e0a6c0e2 100644
--- a/drivers/usb/phy/phy-rcar-gen2-usb.c
+++ b/drivers/usb/phy/phy-rcar-gen2-usb.c
@@ -213,7 +213,7 @@ static int rcar_gen2_usb_phy_probe(struct platform_device *pdev)
 	priv->phy.shutdown = rcar_gen2_usb_phy_shutdown;
 	priv->phy.set_suspend = rcar_gen2_usb_phy_set_suspend;
 
-	retval = usb_add_phy(&priv->phy, USB_PHY_TYPE_USB2);
+	retval = usb_add_phy_dev(&priv->phy);
 	if (retval < 0) {
 		dev_err(dev, "Failed to add USB phy\n");
 		return retval;
diff --git a/drivers/usb/phy/phy-tahvo.c b/drivers/usb/phy/phy-tahvo.c
new file mode 100644
index 00000000000..cc61ee44b91
--- /dev/null
+++ b/drivers/usb/phy/phy-tahvo.c
@@ -0,0 +1,457 @@
+/*
+ * Tahvo USB transceiver driver
+ *
+ * Copyright (C) 2005-2006 Nokia Corporation
+ *
+ * Parts copied from isp1301_omap.c.
+ * Copyright (C) 2004 Texas Instruments
+ * Copyright (C) 2004 David Brownell
+ *
+ * Original driver written by Juha Yrjölä, Tony Lindgren and Timo Teräs.
+ * Modified for Retu/Tahvo MFD by Aaro Koskinen.
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/usb.h>
+#include <linux/extcon.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/usb/otg.h>
+#include <linux/mfd/retu.h>
+#include <linux/usb/gadget.h>
+#include <linux/platform_device.h>
+
+#define DRIVER_NAME     "tahvo-usb"
+
+#define TAHVO_REG_IDSR	0x02
+#define TAHVO_REG_USBR	0x06
+
+#define USBR_SLAVE_CONTROL	(1 << 8)
+#define USBR_VPPVIO_SW		(1 << 7)
+#define USBR_SPEED		(1 << 6)
+#define USBR_REGOUT		(1 << 5)
+#define USBR_MASTER_SW2		(1 << 4)
+#define USBR_MASTER_SW1		(1 << 3)
+#define USBR_SLAVE_SW		(1 << 2)
+#define USBR_NSUSPEND		(1 << 1)
+#define USBR_SEMODE		(1 << 0)
+
+#define TAHVO_MODE_HOST		0
+#define TAHVO_MODE_PERIPHERAL	1
+
+struct tahvo_usb {
+	struct platform_device	*pt_dev;
+	struct usb_phy		phy;
+	int			vbus_state;
+	struct mutex		serialize;
+	struct clk		*ick;
+	int			irq;
+	int			tahvo_mode;
+	struct extcon_dev	extcon;
+};
+
+static const char *tahvo_cable[] = {
+	"USB-HOST",
+	"USB",
+	NULL,
+};
+
+static ssize_t vbus_state_show(struct device *device,
+			       struct device_attribute *attr, char *buf)
+{
+	struct tahvo_usb *tu = dev_get_drvdata(device);
+	return sprintf(buf, "%s\n", tu->vbus_state ? "on" : "off");
+}
+static DEVICE_ATTR(vbus, 0444, vbus_state_show, NULL);
+
+static void check_vbus_state(struct tahvo_usb *tu)
+{
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+	int reg, prev_state;
+
+	reg = retu_read(rdev, TAHVO_REG_IDSR);
+	if (reg & TAHVO_STAT_VBUS) {
+		switch (tu->phy.state) {
+		case OTG_STATE_B_IDLE:
+			/* Enable the gadget driver */
+			if (tu->phy.otg->gadget)
+				usb_gadget_vbus_connect(tu->phy.otg->gadget);
+			tu->phy.state = OTG_STATE_B_PERIPHERAL;
+			break;
+		case OTG_STATE_A_IDLE:
+			/*
+			 * Session is now valid assuming the USB hub is driving
+			 * Vbus.
+			 */
+			tu->phy.state = OTG_STATE_A_HOST;
+			break;
+		default:
+			break;
+		}
+		dev_info(&tu->pt_dev->dev, "USB cable connected\n");
+	} else {
+		switch (tu->phy.state) {
+		case OTG_STATE_B_PERIPHERAL:
+			if (tu->phy.otg->gadget)
+				usb_gadget_vbus_disconnect(tu->phy.otg->gadget);
+			tu->phy.state = OTG_STATE_B_IDLE;
+			break;
+		case OTG_STATE_A_HOST:
+			tu->phy.state = OTG_STATE_A_IDLE;
+			break;
+		default:
+			break;
+		}
+		dev_info(&tu->pt_dev->dev, "USB cable disconnected\n");
+	}
+
+	prev_state = tu->vbus_state;
+	tu->vbus_state = reg & TAHVO_STAT_VBUS;
+	if (prev_state != tu->vbus_state) {
+		extcon_set_cable_state(&tu->extcon, "USB", tu->vbus_state);
+		sysfs_notify(&tu->pt_dev->dev.kobj, NULL, "vbus_state");
+	}
+}
+
+static void tahvo_usb_become_host(struct tahvo_usb *tu)
+{
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+
+	extcon_set_cable_state(&tu->extcon, "USB-HOST", true);
+
+	/* Power up the transceiver in USB host mode */
+	retu_write(rdev, TAHVO_REG_USBR, USBR_REGOUT | USBR_NSUSPEND |
+		   USBR_MASTER_SW2 | USBR_MASTER_SW1);
+	tu->phy.state = OTG_STATE_A_IDLE;
+
+	check_vbus_state(tu);
+}
+
+static void tahvo_usb_stop_host(struct tahvo_usb *tu)
+{
+	tu->phy.state = OTG_STATE_A_IDLE;
+}
+
+static void tahvo_usb_become_peripheral(struct tahvo_usb *tu)
+{
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+
+	extcon_set_cable_state(&tu->extcon, "USB-HOST", false);
+
+	/* Power up transceiver and set it in USB peripheral mode */
+	retu_write(rdev, TAHVO_REG_USBR, USBR_SLAVE_CONTROL | USBR_REGOUT |
+		   USBR_NSUSPEND | USBR_SLAVE_SW);
+	tu->phy.state = OTG_STATE_B_IDLE;
+
+	check_vbus_state(tu);
+}
+
+static void tahvo_usb_stop_peripheral(struct tahvo_usb *tu)
+{
+	if (tu->phy.otg->gadget)
+		usb_gadget_vbus_disconnect(tu->phy.otg->gadget);
+	tu->phy.state = OTG_STATE_B_IDLE;
+}
+
+static void tahvo_usb_power_off(struct tahvo_usb *tu)
+{
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+
+	/* Disable gadget controller if any */
+	if (tu->phy.otg->gadget)
+		usb_gadget_vbus_disconnect(tu->phy.otg->gadget);
+
+	/* Power off transceiver */
+	retu_write(rdev, TAHVO_REG_USBR, 0);
+	tu->phy.state = OTG_STATE_UNDEFINED;
+}
+
+static int tahvo_usb_set_suspend(struct usb_phy *dev, int suspend)
+{
+	struct tahvo_usb *tu = container_of(dev, struct tahvo_usb, phy);
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+	u16 w;
+
+	dev_dbg(&tu->pt_dev->dev, "%s\n", __func__);
+
+	w = retu_read(rdev, TAHVO_REG_USBR);
+	if (suspend)
+		w &= ~USBR_NSUSPEND;
+	else
+		w |= USBR_NSUSPEND;
+	retu_write(rdev, TAHVO_REG_USBR, w);
+
+	return 0;
+}
+
+static int tahvo_usb_set_host(struct usb_otg *otg, struct usb_bus *host)
+{
+	struct tahvo_usb *tu = container_of(otg->phy, struct tahvo_usb, phy);
+
+	dev_dbg(&tu->pt_dev->dev, "%s %p\n", __func__, host);
+
+	mutex_lock(&tu->serialize);
+
+	if (host == NULL) {
+		if (tu->tahvo_mode == TAHVO_MODE_HOST)
+			tahvo_usb_power_off(tu);
+		otg->host = NULL;
+		mutex_unlock(&tu->serialize);
+		return 0;
+	}
+
+	if (tu->tahvo_mode == TAHVO_MODE_HOST) {
+		otg->host = NULL;
+		tahvo_usb_become_host(tu);
+	}
+
+	otg->host = host;
+
+	mutex_unlock(&tu->serialize);
+
+	return 0;
+}
+
+static int tahvo_usb_set_peripheral(struct usb_otg *otg,
+				    struct usb_gadget *gadget)
+{
+	struct tahvo_usb *tu = container_of(otg->phy, struct tahvo_usb, phy);
+
+	dev_dbg(&tu->pt_dev->dev, "%s %p\n", __func__, gadget);
+
+	mutex_lock(&tu->serialize);
+
+	if (!gadget) {
+		if (tu->tahvo_mode == TAHVO_MODE_PERIPHERAL)
+			tahvo_usb_power_off(tu);
+		tu->phy.otg->gadget = NULL;
+		mutex_unlock(&tu->serialize);
+		return 0;
+	}
+
+	tu->phy.otg->gadget = gadget;
+	if (tu->tahvo_mode == TAHVO_MODE_PERIPHERAL)
+		tahvo_usb_become_peripheral(tu);
+
+	mutex_unlock(&tu->serialize);
+
+	return 0;
+}
+
+static irqreturn_t tahvo_usb_vbus_interrupt(int irq, void *_tu)
+{
+	struct tahvo_usb *tu = _tu;
+
+	mutex_lock(&tu->serialize);
+	check_vbus_state(tu);
+	mutex_unlock(&tu->serialize);
+
+	return IRQ_HANDLED;
+}
+
+static ssize_t otg_mode_show(struct device *device,
+			     struct device_attribute *attr, char *buf)
+{
+	struct tahvo_usb *tu = dev_get_drvdata(device);
+
+	switch (tu->tahvo_mode) {
+	case TAHVO_MODE_HOST:
+		return sprintf(buf, "host\n");
+	case TAHVO_MODE_PERIPHERAL:
+		return sprintf(buf, "peripheral\n");
+	}
+
+	return -EINVAL;
+}
+
+static ssize_t otg_mode_store(struct device *device,
+			      struct device_attribute *attr,
+			      const char *buf, size_t count)
+{
+	struct tahvo_usb *tu = dev_get_drvdata(device);
+	int r;
+
+	mutex_lock(&tu->serialize);
+	if (count >= 4 && strncmp(buf, "host", 4) == 0) {
+		if (tu->tahvo_mode == TAHVO_MODE_PERIPHERAL)
+			tahvo_usb_stop_peripheral(tu);
+		tu->tahvo_mode = TAHVO_MODE_HOST;
+		if (tu->phy.otg->host) {
+			dev_info(device, "HOST mode: host controller present\n");
+			tahvo_usb_become_host(tu);
+		} else {
+			dev_info(device, "HOST mode: no host controller, powering off\n");
+			tahvo_usb_power_off(tu);
+		}
+		r = strlen(buf);
+	} else if (count >= 10 && strncmp(buf, "peripheral", 10) == 0) {
+		if (tu->tahvo_mode == TAHVO_MODE_HOST)
+			tahvo_usb_stop_host(tu);
+		tu->tahvo_mode = TAHVO_MODE_PERIPHERAL;
+		if (tu->phy.otg->gadget) {
+			dev_info(device, "PERIPHERAL mode: gadget driver present\n");
+			tahvo_usb_become_peripheral(tu);
+		} else {
+			dev_info(device, "PERIPHERAL mode: no gadget driver, powering off\n");
+			tahvo_usb_power_off(tu);
+		}
+		r = strlen(buf);
+	} else {
+		r = -EINVAL;
+	}
+	mutex_unlock(&tu->serialize);
+
+	return r;
+}
+static DEVICE_ATTR(otg_mode, 0644, otg_mode_show, otg_mode_store);
+
+static struct attribute *tahvo_attributes[] = {
+	&dev_attr_vbus.attr,
+	&dev_attr_otg_mode.attr,
+	NULL
+};
+
+static struct attribute_group tahvo_attr_group = {
+	.attrs = tahvo_attributes,
+};
+
+static int tahvo_usb_probe(struct platform_device *pdev)
+{
+	struct retu_dev *rdev = dev_get_drvdata(pdev->dev.parent);
+	struct tahvo_usb *tu;
+	int ret;
+
+	tu = devm_kzalloc(&pdev->dev, sizeof(*tu), GFP_KERNEL);
+	if (!tu)
+		return -ENOMEM;
+
+	tu->phy.otg = devm_kzalloc(&pdev->dev, sizeof(*tu->phy.otg),
+				   GFP_KERNEL);
+	if (!tu->phy.otg)
+		return -ENOMEM;
+
+	tu->pt_dev = pdev;
+
+	/* Default mode */
+#ifdef CONFIG_TAHVO_USB_HOST_BY_DEFAULT
+	tu->tahvo_mode = TAHVO_MODE_HOST;
+#else
+	tu->tahvo_mode = TAHVO_MODE_PERIPHERAL;
+#endif
+
+	mutex_init(&tu->serialize);
+
+	tu->ick = devm_clk_get(&pdev->dev, "usb_l4_ick");
+	if (!IS_ERR(tu->ick))
+		clk_enable(tu->ick);
+
+	/*
+	 * Set initial state, so that we generate kevents only on state changes.
+	 */
+	tu->vbus_state = retu_read(rdev, TAHVO_REG_IDSR) & TAHVO_STAT_VBUS;
+
+	tu->extcon.name = DRIVER_NAME;
+	tu->extcon.supported_cable = tahvo_cable;
+	tu->extcon.dev.parent = &pdev->dev;
+
+	ret = extcon_dev_register(&tu->extcon);
+	if (ret) {
+		dev_err(&pdev->dev, "could not register extcon device: %d\n",
+			ret);
+		goto err_disable_clk;
+	}
+
+	/* Set the initial cable state. */
+	extcon_set_cable_state(&tu->extcon, "USB-HOST",
+			       tu->tahvo_mode == TAHVO_MODE_HOST);
+	extcon_set_cable_state(&tu->extcon, "USB", tu->vbus_state);
+
+	/* Create OTG interface */
+	tahvo_usb_power_off(tu);
+	tu->phy.dev = &pdev->dev;
+	tu->phy.state = OTG_STATE_UNDEFINED;
+	tu->phy.label = DRIVER_NAME;
+	tu->phy.set_suspend = tahvo_usb_set_suspend;
+
+	tu->phy.otg->phy = &tu->phy;
+	tu->phy.otg->set_host = tahvo_usb_set_host;
+	tu->phy.otg->set_peripheral = tahvo_usb_set_peripheral;
+
+	ret = usb_add_phy(&tu->phy, USB_PHY_TYPE_USB2);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "cannot register USB transceiver: %d\n",
+			ret);
+		goto err_extcon_unreg;
+	}
+
+	dev_set_drvdata(&pdev->dev, tu);
+
+	tu->irq = platform_get_irq(pdev, 0);
+	ret = request_threaded_irq(tu->irq, NULL, tahvo_usb_vbus_interrupt, 0,
+				   "tahvo-vbus", tu);
+	if (ret) {
+		dev_err(&pdev->dev, "could not register tahvo-vbus irq: %d\n",
+			ret);
+		goto err_remove_phy;
+	}
+
+	/* Attributes */
+	ret = sysfs_create_group(&pdev->dev.kobj, &tahvo_attr_group);
+	if (ret) {
+		dev_err(&pdev->dev, "cannot create sysfs group: %d\n", ret);
+		goto err_free_irq;
+	}
+
+	return 0;
+
+err_free_irq:
+	free_irq(tu->irq, tu);
+err_remove_phy:
+	usb_remove_phy(&tu->phy);
+err_extcon_unreg:
+	extcon_dev_unregister(&tu->extcon);
+err_disable_clk:
+	if (!IS_ERR(tu->ick))
+		clk_disable(tu->ick);
+
+	return ret;
+}
+
+static int tahvo_usb_remove(struct platform_device *pdev)
+{
+	struct tahvo_usb *tu = platform_get_drvdata(pdev);
+
+	sysfs_remove_group(&pdev->dev.kobj, &tahvo_attr_group);
+	free_irq(tu->irq, tu);
+	usb_remove_phy(&tu->phy);
+	extcon_dev_unregister(&tu->extcon);
+	if (!IS_ERR(tu->ick))
+		clk_disable(tu->ick);
+
+	return 0;
+}
+
+static struct platform_driver tahvo_usb_driver = {
+	.probe		= tahvo_usb_probe,
+	.remove		= tahvo_usb_remove,
+	.driver		= {
+		.name	= "tahvo-usb",
+		.owner	= THIS_MODULE,
+	},
+};
+module_platform_driver(tahvo_usb_driver);
+
+MODULE_DESCRIPTION("Tahvo USB transceiver driver");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Juha Yrjölä, Tony Lindgren, and Timo Teräs");
+MODULE_AUTHOR("Aaro Koskinen <aaro.koskinen@iki.fi>");
diff --git a/drivers/usb/phy/phy-twl6030-usb.c b/drivers/usb/phy/phy-twl6030-usb.c
index bad57ce77ba..214172b68d5 100644
--- a/drivers/usb/phy/phy-twl6030-usb.c
+++ b/drivers/usb/phy/phy-twl6030-usb.c
@@ -328,7 +328,7 @@ static int twl6030_usb_probe(struct platform_device *pdev)
 	struct device		*dev = &pdev->dev;
 	struct twl4030_usb_data	*pdata = dev_get_platdata(dev);
 
-	twl = devm_kzalloc(dev, sizeof *twl, GFP_KERNEL);
+	twl = devm_kzalloc(dev, sizeof(*twl), GFP_KERNEL);
 	if (!twl)
 		return -ENOMEM;
 
diff --git a/drivers/usb/phy/phy.c b/drivers/usb/phy/phy.c
index 1b74523e1fe..e6f61e4361d 100644
--- a/drivers/usb/phy/phy.c
+++ b/drivers/usb/phy/phy.c
@@ -329,6 +329,8 @@ int usb_add_phy(struct usb_phy *x, enum usb_phy_type type)
 		return -EINVAL;
 	}
 
+	ATOMIC_INIT_NOTIFIER_HEAD(&x->notifier);
+
 	spin_lock_irqsave(&phy_lock, flags);
 
 	list_for_each_entry(phy, &phy_list, head) {
@@ -367,6 +369,8 @@ int usb_add_phy_dev(struct usb_phy *x)
 		return -EINVAL;
 	}
 
+	ATOMIC_INIT_NOTIFIER_HEAD(&x->notifier);
+
 	spin_lock_irqsave(&phy_lock, flags);
 	list_for_each_entry(phy_bind, &phy_bind_list, list)
 		if (!(strcmp(phy_bind->phy_dev_name, dev_name(x->dev))))