diff options
Diffstat (limited to 'drivers/usb/serial')
-rw-r--r-- | drivers/usb/serial/cyberjack.c | 7 | ||||
-rw-r--r-- | drivers/usb/serial/cypress_m8.c | 4 | ||||
-rw-r--r-- | drivers/usb/serial/empeg.c | 6 | ||||
-rw-r--r-- | drivers/usb/serial/ftdi_sio.c | 27 | ||||
-rw-r--r-- | drivers/usb/serial/ftdi_sio.h | 6 | ||||
-rw-r--r-- | drivers/usb/serial/garmin_gps.c | 8 | ||||
-rw-r--r-- | drivers/usb/serial/generic.c | 6 | ||||
-rw-r--r-- | drivers/usb/serial/io_edgeport.c | 8 | ||||
-rw-r--r-- | drivers/usb/serial/io_ti.c | 8 | ||||
-rw-r--r-- | drivers/usb/serial/ipaq.c | 6 | ||||
-rw-r--r-- | drivers/usb/serial/ipw.c | 3 | ||||
-rw-r--r-- | drivers/usb/serial/iuu_phoenix.c | 1 | ||||
-rw-r--r-- | drivers/usb/serial/kobil_sct.c | 6 | ||||
-rw-r--r-- | drivers/usb/serial/mos7720.c | 7 | ||||
-rw-r--r-- | drivers/usb/serial/mos7840.c | 43 | ||||
-rw-r--r-- | drivers/usb/serial/opticon.c | 8 | ||||
-rw-r--r-- | drivers/usb/serial/option.c | 3 | ||||
-rw-r--r-- | drivers/usb/serial/sierra.c | 24 | ||||
-rw-r--r-- | drivers/usb/serial/ti_usb_3410_5052.c | 14 | ||||
-rw-r--r-- | drivers/usb/serial/usb-serial.c | 105 | ||||
-rw-r--r-- | drivers/usb/serial/visor.c | 8 |
21 files changed, 135 insertions, 173 deletions
diff --git a/drivers/usb/serial/cyberjack.c b/drivers/usb/serial/cyberjack.c index 858bdd038fb..dd501bb63ed 100644 --- a/drivers/usb/serial/cyberjack.c +++ b/drivers/usb/serial/cyberjack.c @@ -175,13 +175,6 @@ static int cyberjack_open(struct tty_struct *tty, dbg("%s - usb_clear_halt", __func__); usb_clear_halt(port->serial->dev, port->write_urb->pipe); - /* force low_latency on so that our tty_push actually forces - * the data through, otherwise it is scheduled, and with high - * data rates (like with OHCI) data can get lost. - */ - if (tty) - tty->low_latency = 1; - priv = usb_get_serial_port_data(port); spin_lock_irqsave(&priv->lock, flags); priv->rdtodo = 0; diff --git a/drivers/usb/serial/cypress_m8.c b/drivers/usb/serial/cypress_m8.c index eae4740d448..e568710b263 100644 --- a/drivers/usb/serial/cypress_m8.c +++ b/drivers/usb/serial/cypress_m8.c @@ -656,10 +656,6 @@ static int cypress_open(struct tty_struct *tty, priv->rx_flags = 0; spin_unlock_irqrestore(&priv->lock, flags); - /* setting to zero could cause data loss */ - if (tty) - tty->low_latency = 1; - /* raise both lines and set termios */ spin_lock_irqsave(&priv->lock, flags); priv->line_control = CONTROL_DTR | CONTROL_RTS; diff --git a/drivers/usb/serial/empeg.c b/drivers/usb/serial/empeg.c index 8a69cce40b6..c709ec474a8 100644 --- a/drivers/usb/serial/empeg.c +++ b/drivers/usb/serial/empeg.c @@ -478,12 +478,6 @@ static void empeg_set_termios(struct tty_struct *tty, termios->c_cflag |= CS8; /* character size 8 bits */ - /* - * Force low_latency on; otherwise the pushes are scheduled; - * this is bad as it opens up the possibility of dropping bytes - * on the floor. We don't want to drop bytes on the floor. :) - */ - tty->low_latency = 1; tty_encode_baud_rate(tty, 115200, 115200); } diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index 8100f1d2590..d9fcdaedf38 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -56,6 +56,7 @@ static __u16 vendor = FTDI_VID; static __u16 product; struct ftdi_private { + struct kref kref; ftdi_chip_type_t chip_type; /* type of device, either SIO or FT8U232AM */ int baud_base; /* baud base clock for divisor setting */ @@ -669,6 +670,8 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(ADI_VID, ADI_GNICE_PID), .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { USB_DEVICE(JETI_VID, JETI_SPC1201_PID) }, + { USB_DEVICE(MARVELL_VID, MARVELL_SHEEVAPLUG_PID), + .driver_info = (kernel_ulong_t)&ftdi_jtag_quirk }, { }, /* Optional parameter entry */ { } /* Terminating entry */ }; @@ -1352,6 +1355,7 @@ static int ftdi_sio_port_probe(struct usb_serial_port *port) return -ENOMEM; } + kref_init(&priv->kref); spin_lock_init(&priv->rx_lock); spin_lock_init(&priv->tx_lock); init_waitqueue_head(&priv->delta_msr_wait); @@ -1468,6 +1472,13 @@ static void ftdi_shutdown(struct usb_serial *serial) dbg("%s", __func__); } +static void ftdi_sio_priv_release(struct kref *k) +{ + struct ftdi_private *priv = container_of(k, struct ftdi_private, kref); + + kfree(priv); +} + static int ftdi_sio_port_remove(struct usb_serial_port *port) { struct ftdi_private *priv = usb_get_serial_port_data(port); @@ -1476,14 +1487,7 @@ static int ftdi_sio_port_remove(struct usb_serial_port *port) remove_sysfs_attrs(port); - /* all open ports are closed at this point - * (by usbserial.c:__serial_close, which calls ftdi_close) - */ - - if (priv) { - usb_set_serial_port_data(port, NULL); - kfree(priv); - } + kref_put(&priv->kref, ftdi_sio_priv_release); return 0; } @@ -1547,7 +1551,8 @@ static int ftdi_open(struct tty_struct *tty, dev_err(&port->dev, "%s - failed submitting read urb, error %d\n", __func__, result); - + else + kref_get(&priv->kref); return result; } /* ftdi_open */ @@ -1589,11 +1594,11 @@ static void ftdi_close(struct tty_struct *tty, mutex_unlock(&port->serial->disc_mutex); /* cancel any scheduled reading */ - cancel_delayed_work(&priv->rx_work); - flush_scheduled_work(); + cancel_delayed_work_sync(&priv->rx_work); /* shutdown our bulk read */ usb_kill_urb(port->read_urb); + kref_put(&priv->kref, ftdi_sio_priv_release); } /* ftdi_close */ diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h index c09f658a448..12330fa1c09 100644 --- a/drivers/usb/serial/ftdi_sio.h +++ b/drivers/usb/serial/ftdi_sio.h @@ -920,6 +920,12 @@ #define JETI_SPC1201_PID 0x04b2 /* + * Marvell SheevaPlug + */ +#define MARVELL_VID 0x9e88 +#define MARVELL_SHEEVAPLUG_PID 0x9e8f + +/* * BmRequestType: 1100 0000b * bRequest: FTDI_E2_READ * wValue: 0 diff --git a/drivers/usb/serial/garmin_gps.c b/drivers/usb/serial/garmin_gps.c index a26a0e2cdb4..586d30ff450 100644 --- a/drivers/usb/serial/garmin_gps.c +++ b/drivers/usb/serial/garmin_gps.c @@ -973,14 +973,6 @@ static int garmin_open(struct tty_struct *tty, dbg("%s - port %d", __func__, port->number); - /* - * Force low_latency on so that our tty_push actually forces the data - * through, otherwise it is scheduled, and with high data rates (like - * with OHCI) data can get lost. - */ - if (tty) - tty->low_latency = 1; - spin_lock_irqsave(&garmin_data_p->lock, flags); garmin_data_p->mode = initial_mode; garmin_data_p->count = 0; diff --git a/drivers/usb/serial/generic.c b/drivers/usb/serial/generic.c index 9d57cace373..4cec9906ccf 100644 --- a/drivers/usb/serial/generic.c +++ b/drivers/usb/serial/generic.c @@ -122,12 +122,6 @@ int usb_serial_generic_open(struct tty_struct *tty, dbg("%s - port %d", __func__, port->number); - /* force low_latency on so that our tty_push actually forces the data - through, otherwise it is scheduled, and with high data rates (like - with OHCI) data can get lost. */ - if (tty) - tty->low_latency = 1; - /* clear the throttle flags */ spin_lock_irqsave(&port->lock, flags); port->throttled = 0; diff --git a/drivers/usb/serial/io_edgeport.c b/drivers/usb/serial/io_edgeport.c index e85c8c0d1ad..fb4a73d090f 100644 --- a/drivers/usb/serial/io_edgeport.c +++ b/drivers/usb/serial/io_edgeport.c @@ -193,8 +193,6 @@ static const struct divisor_table_entry divisor_table[] = { /* local variables */ static int debug; -static int low_latency = 1; /* tty low latency flag, on by default */ - static atomic_t CmdUrbs; /* Number of outstanding Command Write Urbs */ @@ -867,9 +865,6 @@ static int edge_open(struct tty_struct *tty, if (edge_port == NULL) return -ENODEV; - if (tty) - tty->low_latency = low_latency; - /* see if we've set up our endpoint info yet (can't set it up in edge_startup as the structures were not set up at that time.) */ serial = port->serial; @@ -3299,6 +3294,3 @@ MODULE_FIRMWARE("edgeport/down2.fw"); module_param(debug, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(debug, "Debug enabled or not"); - -module_param(low_latency, bool, S_IRUGO | S_IWUSR); -MODULE_PARM_DESC(low_latency, "Low latency enabled or not"); diff --git a/drivers/usb/serial/io_ti.c b/drivers/usb/serial/io_ti.c index c3cdd00ddc4..513b25e044c 100644 --- a/drivers/usb/serial/io_ti.c +++ b/drivers/usb/serial/io_ti.c @@ -76,7 +76,6 @@ struct edgeport_uart_buf_desc { #define EDGE_READ_URB_STOPPING 1 #define EDGE_READ_URB_STOPPED 2 -#define EDGE_LOW_LATENCY 1 #define EDGE_CLOSING_WAIT 4000 /* in .01 sec */ #define EDGE_OUT_BUF_SIZE 1024 @@ -232,7 +231,6 @@ static unsigned short OperationalBuildNumber; static int debug; -static int low_latency = EDGE_LOW_LATENCY; static int closing_wait = EDGE_CLOSING_WAIT; static int ignore_cpu_rev; static int default_uart_mode; /* RS232 */ @@ -1850,9 +1848,6 @@ static int edge_open(struct tty_struct *tty, if (edge_port == NULL) return -ENODEV; - if (tty) - tty->low_latency = low_latency; - port_number = port->number - port->serial->minor; switch (port_number) { case 0: @@ -3008,9 +3003,6 @@ MODULE_FIRMWARE("edgeport/down3.bin"); module_param(debug, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(debug, "Debug enabled or not"); -module_param(low_latency, bool, S_IRUGO | S_IWUSR); -MODULE_PARM_DESC(low_latency, "Low latency enabled or not"); - module_param(closing_wait, int, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(closing_wait, "Maximum wait for data to drain, in .01 secs"); diff --git a/drivers/usb/serial/ipaq.c b/drivers/usb/serial/ipaq.c index ef92095b073..cd62825a9ac 100644 --- a/drivers/usb/serial/ipaq.c +++ b/drivers/usb/serial/ipaq.c @@ -631,13 +631,7 @@ static int ipaq_open(struct tty_struct *tty, priv->free_len += PACKET_SIZE; } - /* - * Force low latency on. This will immediately push data to the line - * discipline instead of queueing. - */ - if (tty) { - tty->low_latency = 1; /* FIXME: These two are bogus */ tty->raw = 1; tty->real_raw = 1; diff --git a/drivers/usb/serial/ipw.c b/drivers/usb/serial/ipw.c index f530032ed93..da2a2b46644 100644 --- a/drivers/usb/serial/ipw.c +++ b/drivers/usb/serial/ipw.c @@ -207,9 +207,6 @@ static int ipw_open(struct tty_struct *tty, if (!buf_flow_init) return -ENOMEM; - if (tty) - tty->low_latency = 1; - /* --1: Tell the modem to initialize (we think) From sniffs this is * always the first thing that gets sent to the modem during * opening of the device */ diff --git a/drivers/usb/serial/iuu_phoenix.c b/drivers/usb/serial/iuu_phoenix.c index 2314c6ae4fc..4473d442b2a 100644 --- a/drivers/usb/serial/iuu_phoenix.c +++ b/drivers/usb/serial/iuu_phoenix.c @@ -1051,7 +1051,6 @@ static int iuu_open(struct tty_struct *tty, tty->termios->c_oflag = 0; tty->termios->c_iflag = 0; priv->termios_initialized = 1; - tty->low_latency = 1; priv->poll = 0; } spin_unlock_irqrestore(&priv->lock, flags); diff --git a/drivers/usb/serial/kobil_sct.c b/drivers/usb/serial/kobil_sct.c index 6286baad939..c148544953b 100644 --- a/drivers/usb/serial/kobil_sct.c +++ b/drivers/usb/serial/kobil_sct.c @@ -231,13 +231,7 @@ static int kobil_open(struct tty_struct *tty, /* someone sets the dev to 0 if the close method has been called */ port->interrupt_in_urb->dev = port->serial->dev; - - /* force low_latency on so that our tty_push actually forces - * the data through, otherwise it is scheduled, and with high - * data rates (like with OHCI) data can get lost. - */ if (tty) { - tty->low_latency = 1; /* Default to echo off and other sane device settings */ tty->termios->c_lflag = 0; diff --git a/drivers/usb/serial/mos7720.c b/drivers/usb/serial/mos7720.c index e772cc0a97f..24e3b5d4b4d 100644 --- a/drivers/usb/serial/mos7720.c +++ b/drivers/usb/serial/mos7720.c @@ -446,13 +446,6 @@ static int mos7720_open(struct tty_struct *tty, data = 0x0c; send_mos_cmd(serial, MOS_WRITE, port_number, 0x01, &data); - /* force low_latency on so that our tty_push actually forces * - * the data through,otherwise it is scheduled, and with * - * high data rates (like with OHCI) data can get lost. */ - - if (tty) - tty->low_latency = 1; - /* see if we've set up our endpoint info yet * * (can't set it up in mos7720_startup as the * * structures were not set up at that time.) */ diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c index 2c20e88a91b..84fb1dcd30d 100644 --- a/drivers/usb/serial/mos7840.c +++ b/drivers/usb/serial/mos7840.c @@ -38,7 +38,7 @@ /* * Version Information */ -#define DRIVER_VERSION "1.3.1" +#define DRIVER_VERSION "1.3.2" #define DRIVER_DESC "Moschip 7840/7820 USB Serial Driver" /* @@ -123,6 +123,11 @@ #define BANDB_DEVICE_ID_USOPTL4_4 0xAC44 #define BANDB_DEVICE_ID_USOPTL4_2 0xAC42 +/* This driver also supports the ATEN UC2324 device since it is mos7840 based + * - if I knew the device id it would also support the ATEN UC2322 */ +#define USB_VENDOR_ID_ATENINTL 0x0557 +#define ATENINTL_DEVICE_ID_UC2324 0x2011 + /* Interrupt Routine Defines */ #define SERIAL_IIR_RLS 0x06 @@ -170,6 +175,7 @@ static struct usb_device_id moschip_port_id_table[] = { {USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7820)}, {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4)}, {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2)}, + {USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2324)}, {} /* terminating entry */ }; @@ -178,6 +184,7 @@ static __devinitdata struct usb_device_id moschip_id_table_combined[] = { {USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7820)}, {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4)}, {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2)}, + {USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2324)}, {} /* terminating entry */ }; @@ -1000,12 +1007,6 @@ static int mos7840_open(struct tty_struct *tty, status = mos7840_set_reg_sync(port, mos7840_port->ControlRegOffset, Data); - /* force low_latency on so that our tty_push actually forces * - * the data through,otherwise it is scheduled, and with * - * high data rates (like with OHCI) data can get lost. */ - if (tty) - tty->low_latency = 1; - /* Check to see if we've set up our endpoint info yet * * (can't set it up in mos7840_startup as the structures * * were not set up at that time.) */ @@ -2477,9 +2478,14 @@ static int mos7840_startup(struct usb_serial *serial) mos7840_set_port_private(serial->port[i], mos7840_port); spin_lock_init(&mos7840_port->pool_lock); - mos7840_port->port_num = ((serial->port[i]->number - - (serial->port[i]->serial->minor)) + - 1); + /* minor is not initialised until later by + * usb-serial.c:get_free_serial() and cannot therefore be used + * to index device instances */ + mos7840_port->port_num = i + 1; + dbg ("serial->port[i]->number = %d", serial->port[i]->number); + dbg ("serial->port[i]->serial->minor = %d", serial->port[i]->serial->minor); + dbg ("mos7840_port->port_num = %d", mos7840_port->port_num); + dbg ("serial->minor = %d", serial->minor); if (mos7840_port->port_num == 1) { mos7840_port->SpRegOffset = 0x0; @@ -2690,13 +2696,16 @@ static void mos7840_shutdown(struct usb_serial *serial) for (i = 0; i < serial->num_ports; ++i) { mos7840_port = mos7840_get_port_private(serial->port[i]); - spin_lock_irqsave(&mos7840_port->pool_lock, flags); - mos7840_port->zombie = 1; - spin_unlock_irqrestore(&mos7840_port->pool_lock, flags); - usb_kill_urb(mos7840_port->control_urb); - kfree(mos7840_port->ctrl_buf); - kfree(mos7840_port->dr); - kfree(mos7840_port); + dbg ("mos7840_port %d = %p", i, mos7840_port); + if (mos7840_port) { + spin_lock_irqsave(&mos7840_port->pool_lock, flags); + mos7840_port->zombie = 1; + spin_unlock_irqrestore(&mos7840_port->pool_lock, flags); + usb_kill_urb(mos7840_port->control_urb); + kfree(mos7840_port->ctrl_buf); + kfree(mos7840_port->dr); + kfree(mos7840_port); + } mos7840_set_port_private(serial->port[i], NULL); } diff --git a/drivers/usb/serial/opticon.c b/drivers/usb/serial/opticon.c index 839583dc8b6..b500ad10b75 100644 --- a/drivers/usb/serial/opticon.c +++ b/drivers/usb/serial/opticon.c @@ -159,14 +159,6 @@ static int opticon_open(struct tty_struct *tty, struct usb_serial_port *port, priv->port = port; spin_unlock_irqrestore(&priv->lock, flags); - /* - * Force low_latency on so that our tty_push actually forces the data - * through, otherwise it is scheduled, and with high data rates (like - * with OHCI) data can get lost. - */ - if (tty) - tty->low_latency = 1; - /* Start reading from the device */ usb_fill_bulk_urb(priv->bulk_read_urb, priv->udev, usb_rcvbulkpipe(priv->udev, diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 47bd070f24b..7817b82889c 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -936,9 +936,6 @@ static int option_open(struct tty_struct *tty, usb_pipeout(urb->pipe), 0); */ } - if (tty) - tty->low_latency = 1; - option_send_setup(tty, port); return 0; diff --git a/drivers/usb/serial/sierra.c b/drivers/usb/serial/sierra.c index d9bf9a5c20e..913225c6161 100644 --- a/drivers/usb/serial/sierra.c +++ b/drivers/usb/serial/sierra.c @@ -14,7 +14,7 @@ Whom based his on the Keyspan driver by Hugh Blemings <hugh@blemings.org> */ -#define DRIVER_VERSION "v.1.3.2" +#define DRIVER_VERSION "v.1.3.3" #define DRIVER_AUTHOR "Kevin Lloyd <klloyd@sierrawireless.com>" #define DRIVER_DESC "USB Driver for Sierra Wireless USB modems" @@ -259,9 +259,21 @@ static int sierra_send_setup(struct tty_struct *tty, val |= 0x02; /* If composite device then properly report interface */ - if (serial->num_ports == 1) + if (serial->num_ports == 1) { interface = sierra_calc_interface(serial); + /* Control message is sent only to interfaces with + * interrupt_in endpoints + */ + if (port->interrupt_in_urb) { + /* send control message */ + return usb_control_msg(serial->dev, + usb_rcvctrlpipe(serial->dev, 0), + 0x22, 0x21, val, interface, + NULL, 0, USB_CTRL_SET_TIMEOUT); + } + } + /* Otherwise the need to do non-composite mapping */ else { if (port->bulk_out_endpointAddress == 2) @@ -270,12 +282,13 @@ static int sierra_send_setup(struct tty_struct *tty, interface = 1; else if (port->bulk_out_endpointAddress == 5) interface = 2; - } - return usb_control_msg(serial->dev, + return usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), 0x22, 0x21, val, interface, NULL, 0, USB_CTRL_SET_TIMEOUT); + + } } return 0; @@ -585,9 +598,6 @@ static int sierra_open(struct tty_struct *tty, } } - if (tty) - tty->low_latency = 1; - sierra_send_setup(tty, port); /* start up the interrupt endpoint if we have one */ diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c index 9c4c700c7cc..0a64bac306e 100644 --- a/drivers/usb/serial/ti_usb_3410_5052.c +++ b/drivers/usb/serial/ti_usb_3410_5052.c @@ -50,11 +50,10 @@ #define TI_TRANSFER_TIMEOUT 2 -#define TI_DEFAULT_LOW_LATENCY 0 #define TI_DEFAULT_CLOSING_WAIT 4000 /* in .01 secs */ /* supported setserial flags */ -#define TI_SET_SERIAL_FLAGS (ASYNC_LOW_LATENCY) +#define TI_SET_SERIAL_FLAGS 0 /* read urb states */ #define TI_READ_URB_RUNNING 0 @@ -161,7 +160,6 @@ static int ti_buf_get(struct circ_buf *cb, char *buf, int count); /* module parameters */ static int debug; -static int low_latency = TI_DEFAULT_LOW_LATENCY; static int closing_wait = TI_DEFAULT_CLOSING_WAIT; static ushort vendor_3410[TI_EXTRA_VID_PID_COUNT]; static unsigned int vendor_3410_count; @@ -296,10 +294,6 @@ MODULE_FIRMWARE("mts_edge.fw"); module_param(debug, bool, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(debug, "Enable debugging, 0=no, 1=yes"); -module_param(low_latency, bool, S_IRUGO | S_IWUSR); -MODULE_PARM_DESC(low_latency, - "TTY low_latency flag, 0=off, 1=on, default is off"); - module_param(closing_wait, int, S_IRUGO | S_IWUSR); MODULE_PARM_DESC(closing_wait, "Maximum wait for data to drain in close, in .01 secs, default is 4000"); @@ -448,7 +442,6 @@ static int ti_startup(struct usb_serial *serial) spin_lock_init(&tport->tp_lock); tport->tp_uart_base_addr = (i == 0 ? TI_UART1_BASE_ADDR : TI_UART2_BASE_ADDR); - tport->tp_flags = low_latency ? ASYNC_LOW_LATENCY : 0; tport->tp_closing_wait = closing_wait; init_waitqueue_head(&tport->tp_msr_wait); init_waitqueue_head(&tport->tp_write_wait); @@ -528,10 +521,6 @@ static int ti_open(struct tty_struct *tty, if (mutex_lock_interruptible(&tdev->td_open_close_lock)) return -ERESTARTSYS; - if (tty) - tty->low_latency = - (tport->tp_flags & ASYNC_LOW_LATENCY) ? 1 : 0; - port_number = port->number - port->serial->minor; memset(&(tport->tp_icount), 0x00, sizeof(tport->tp_icount)); @@ -1454,7 +1443,6 @@ static int ti_set_serial_info(struct tty_struct *tty, struct ti_port *tport, return -EFAULT; tport->tp_flags = new_serial.flags & TI_SET_SERIAL_FLAGS; - tty->low_latency = (tport->tp_flags & ASYNC_LOW_LATENCY) ? 1 : 0; tport->tp_closing_wait = new_serial.closing_wait; return 0; diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index 2a70563bbee..f331e2bde88 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -137,22 +137,10 @@ static void destroy_serial(struct kref *kref) dbg("%s - %s", __func__, serial->type->description); - serial->type->shutdown(serial); - /* return the minor range that this device had */ if (serial->minor != SERIAL_TTY_NO_MINOR) return_serial(serial); - for (i = 0; i < serial->num_ports; ++i) - serial->port[i]->port.count = 0; - - /* the ports are cleaned up and released in port_release() */ - for (i = 0; i < serial->num_ports; ++i) - if (serial->port[i]->dev.parent != NULL) { - device_unregister(&serial->port[i]->dev); - serial->port[i] = NULL; - } - /* If this is a "fake" port, we have to clean it up here, as it will * not get cleaned up in port_release() as it was never registered with * the driver core */ @@ -187,7 +175,7 @@ static int serial_open (struct tty_struct *tty, struct file *filp) struct usb_serial *serial; struct usb_serial_port *port; unsigned int portNumber; - int retval; + int retval = 0; dbg("%s", __func__); @@ -198,21 +186,24 @@ static int serial_open (struct tty_struct *tty, struct file *filp) return -ENODEV; } + mutex_lock(&serial->disc_mutex); portNumber = tty->index - serial->minor; port = serial->port[portNumber]; - if (!port) { - retval = -ENODEV; - goto bailout_kref_put; - } - - if (port->serial->disconnected) { + if (!port || serial->disconnected) retval = -ENODEV; - goto bailout_kref_put; - } + else + get_device(&port->dev); + /* + * Note: Our locking order requirement does not allow port->mutex + * to be acquired while serial->disc_mutex is held. + */ + mutex_unlock(&serial->disc_mutex); + if (retval) + goto bailout_serial_put; if (mutex_lock_interruptible(&port->mutex)) { retval = -ERESTARTSYS; - goto bailout_kref_put; + goto bailout_port_put; } ++port->port.count; @@ -232,14 +223,20 @@ static int serial_open (struct tty_struct *tty, struct file *filp) goto bailout_mutex_unlock; } - retval = usb_autopm_get_interface(serial->interface); + mutex_lock(&serial->disc_mutex); + if (serial->disconnected) + retval = -ENODEV; + else + retval = usb_autopm_get_interface(serial->interface); if (retval) goto bailout_module_put; + /* only call the device specific open if this * is the first time the port is opened */ retval = serial->type->open(tty, port, filp); if (retval) goto bailout_interface_put; + mutex_unlock(&serial->disc_mutex); } mutex_unlock(&port->mutex); @@ -248,13 +245,16 @@ static int serial_open (struct tty_struct *tty, struct file *filp) bailout_interface_put: usb_autopm_put_interface(serial->interface); bailout_module_put: + mutex_unlock(&serial->disc_mutex); module_put(serial->type->driver.owner); bailout_mutex_unlock: port->port.count = 0; tty->driver_data = NULL; tty_port_tty_set(&port->port, NULL); mutex_unlock(&port->mutex); -bailout_kref_put: +bailout_port_put: + put_device(&port->dev); +bailout_serial_put: usb_serial_put(serial); return retval; } @@ -262,6 +262,9 @@ bailout_kref_put: static void serial_close(struct tty_struct *tty, struct file *filp) { struct usb_serial_port *port = tty->driver_data; + struct usb_serial *serial; + struct module *owner; + int count; if (!port) return; @@ -269,6 +272,8 @@ static void serial_close(struct tty_struct *tty, struct file *filp) dbg("%s - port %d", __func__, port->number); mutex_lock(&port->mutex); + serial = port->serial; + owner = serial->type->driver.owner; if (port->port.count == 0) { mutex_unlock(&port->mutex); @@ -281,7 +286,7 @@ static void serial_close(struct tty_struct *tty, struct file *filp) * this before we drop the port count. The call is protected * by the port mutex */ - port->serial->type->close(tty, port, filp); + serial->type->close(tty, port, filp); if (port->port.count == (port->console ? 2 : 1)) { struct tty_struct *tty = tty_port_tty_get(&port->port); @@ -295,17 +300,23 @@ static void serial_close(struct tty_struct *tty, struct file *filp) } } - if (port->port.count == 1) { - mutex_lock(&port->serial->disc_mutex); - if (!port->serial->disconnected) - usb_autopm_put_interface(port->serial->interface); - mutex_unlock(&port->serial->disc_mutex); - module_put(port->serial->type->driver.owner); - } --port->port.count; - + count = port->port.count; mutex_unlock(&port->mutex); - usb_serial_put(port->serial); + put_device(&port->dev); + + /* Mustn't dereference port any more */ + if (count == 0) { + mutex_lock(&serial->disc_mutex); + if (!serial->disconnected) + usb_autopm_put_interface(serial->interface); + mutex_unlock(&serial->disc_mutex); + } + usb_serial_put(serial); + + /* Mustn't dereference serial any more */ + if (count == 0) + module_put(owner); } static int serial_write(struct tty_struct *tty, const unsigned char *buf, @@ -549,7 +560,13 @@ static void kill_traffic(struct usb_serial_port *port) static void port_free(struct usb_serial_port *port) { + /* + * Stop all the traffic before cancelling the work, so that + * nobody will restart it by calling usb_serial_port_softint. + */ kill_traffic(port); + cancel_work_sync(&port->work); + usb_free_urb(port->read_urb); usb_free_urb(port->write_urb); usb_free_urb(port->interrupt_in_urb); @@ -558,7 +575,6 @@ static void port_free(struct usb_serial_port *port) kfree(port->bulk_out_buffer); kfree(port->interrupt_in_buffer); kfree(port->interrupt_out_buffer); - flush_scheduled_work(); /* port->work */ kfree(port); } @@ -958,6 +974,7 @@ int usb_serial_probe(struct usb_interface *interface, if (retval > 0) { /* quietly accept this device, but don't bind to a serial port as it's about to disappear */ + serial->num_ports = 0; goto exit; } } @@ -1043,6 +1060,12 @@ void usb_serial_disconnect(struct usb_interface *interface) usb_set_intfdata(interface, NULL); /* must set a flag, to signal subdrivers */ serial->disconnected = 1; + mutex_unlock(&serial->disc_mutex); + + /* Unfortunately, many of the sub-drivers expect the port structures + * to exist when their shutdown method is called, so we have to go + * through this awkward two-step unregistration procedure. + */ for (i = 0; i < serial->num_ports; ++i) { port = serial->port[i]; if (port) { @@ -1052,11 +1075,21 @@ void usb_serial_disconnect(struct usb_interface *interface) tty_kref_put(tty); } kill_traffic(port); + cancel_work_sync(&port->work); + device_del(&port->dev); + } + } + serial->type->shutdown(serial); + for (i = 0; i < serial->num_ports; ++i) { + port = serial->port[i]; + if (port) { + put_device(&port->dev); + serial->port[i] = NULL; } } + /* let the last holder of this object * cause it to be cleaned up */ - mutex_unlock(&serial->disc_mutex); usb_serial_put(serial); dev_info(dev, "device disconnected\n"); } diff --git a/drivers/usb/serial/visor.c b/drivers/usb/serial/visor.c index 4facce3d936..5ac414bda71 100644 --- a/drivers/usb/serial/visor.c +++ b/drivers/usb/serial/visor.c @@ -296,14 +296,6 @@ static int visor_open(struct tty_struct *tty, struct usb_serial_port *port, priv->throttled = 0; spin_unlock_irqrestore(&priv->lock, flags); - /* - * Force low_latency on so that our tty_push actually forces the data - * through, otherwise it is scheduled, and with high data rates (like - * with OHCI) data can get lost. - */ - if (tty) - tty->low_latency = 1; - /* Start reading from the device */ usb_fill_bulk_urb(port->read_urb, serial->dev, usb_rcvbulkpipe(serial->dev, |