diff options
Diffstat (limited to 'drivers/usb/storage/scsiglue.c')
| -rw-r--r-- | drivers/usb/storage/scsiglue.c | 55 |
1 files changed, 31 insertions, 24 deletions
diff --git a/drivers/usb/storage/scsiglue.c b/drivers/usb/storage/scsiglue.c index 13b8bcdf3db..a324a5d21e9 100644 --- a/drivers/usb/storage/scsiglue.c +++ b/drivers/usb/storage/scsiglue.c @@ -78,8 +78,6 @@ static const char* host_info(struct Scsi_Host *host) static int slave_alloc (struct scsi_device *sdev) { - struct us_data *us = host_to_us(sdev->host); - /* * Set the INQUIRY transfer length to 36. We don't use any of * the extra data and many devices choke if asked for more or @@ -104,18 +102,6 @@ static int slave_alloc (struct scsi_device *sdev) */ blk_queue_update_dma_alignment(sdev->request_queue, (512 - 1)); - /* - * The UFI spec treates the Peripheral Qualifier bits in an - * INQUIRY result as reserved and requires devices to set them - * to 0. However the SCSI spec requires these bits to be set - * to 3 to indicate when a LUN is not present. - * - * Let the scanning code know if this target merely sets - * Peripheral Device Type to 0x1f to indicate no LUN. - */ - if (us->subclass == USB_SC_UFI) - sdev->sdev_target->pdt_1f_for_no_lun = 1; - return 0; } @@ -197,6 +183,9 @@ static int slave_configure(struct scsi_device *sdev) * page x08, so we will skip it. */ sdev->skip_ms_page_8 = 1; + /* Some devices don't handle VPD pages correctly */ + sdev->skip_vpd_pages = 1; + /* Some disks return the total number of blocks in response * to READ CAPACITY rather than the highest block number. * If this device makes that mistake, tell the sd driver. */ @@ -217,16 +206,6 @@ static int slave_configure(struct scsi_device *sdev) if (sdev->scsi_level > SCSI_SPC_2) us->fflags |= US_FL_SANE_SENSE; - /* Some devices report a SCSI revision level above 2 but are - * unable to handle the REPORT LUNS command (for which - * support is mandatory at level 3). Since we already have - * a Get-Max-LUN request, we won't lose much by setting the - * revision level down to 2. The only devices that would be - * affected are those with sparse LUNs. */ - if (sdev->scsi_level > SCSI_2) - sdev->sdev_target->scsi_level = - sdev->scsi_level = SCSI_2; - /* USB-IDE bridges tend to report SK = 0x04 (Non-recoverable * Hardware Error) when any low-level error occurs, * recoverable or not. Setting this flag tells the SCSI @@ -283,6 +262,33 @@ static int slave_configure(struct scsi_device *sdev) return 0; } +static int target_alloc(struct scsi_target *starget) +{ + struct us_data *us = host_to_us(dev_to_shost(starget->dev.parent)); + + /* + * Some USB drives don't support REPORT LUNS, even though they + * report a SCSI revision level above 2. Tell the SCSI layer + * not to issue that command; it will perform a normal sequential + * scan instead. + */ + starget->no_report_luns = 1; + + /* + * The UFI spec treats the Peripheral Qualifier bits in an + * INQUIRY result as reserved and requires devices to set them + * to 0. However the SCSI spec requires these bits to be set + * to 3 to indicate when a LUN is not present. + * + * Let the scanning code know if this target merely sets + * Peripheral Device Type to 0x1f to indicate no LUN. + */ + if (us->subclass == USB_SC_UFI) + starget->pdt_1f_for_no_lun = 1; + + return 0; +} + /* queue a command */ /* This is always called with scsi_lock(host) held */ static int queuecommand_lck(struct scsi_cmnd *srb, @@ -546,6 +552,7 @@ struct scsi_host_template usb_stor_host_template = { .slave_alloc = slave_alloc, .slave_configure = slave_configure, + .target_alloc = target_alloc, /* lots of sg segments can be handled */ .sg_tablesize = SCSI_MAX_SG_CHAIN_SEGMENTS, |