diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/ata/ahci.c | 157 |
1 files changed, 155 insertions, 2 deletions
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index c8ab947cf35..ed9b407e42d 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -49,6 +49,9 @@ #define DRV_NAME "ahci" #define DRV_VERSION "3.0" +static int ahci_enable_alpm(struct ata_port *ap, + enum link_pm policy); +static void ahci_disable_alpm(struct ata_port *ap); enum { AHCI_PCI_BAR = 5, @@ -99,6 +102,7 @@ enum { HOST_CAP_SSC = (1 << 14), /* Slumber capable */ HOST_CAP_PMP = (1 << 17), /* Port Multiplier support */ HOST_CAP_CLO = (1 << 24), /* Command List Override support */ + HOST_CAP_ALPM = (1 << 26), /* Aggressive Link PM support */ HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */ HOST_CAP_SNTF = (1 << 29), /* SNotification register */ HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */ @@ -155,6 +159,8 @@ enum { PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS, /* PORT_CMD bits */ + PORT_CMD_ASP = (1 << 27), /* Aggressive Slumber/Partial */ + PORT_CMD_ALPE = (1 << 26), /* Aggressive Link PM enable */ PORT_CMD_ATAPI = (1 << 24), /* Device is ATAPI */ PORT_CMD_PMP = (1 << 17), /* PMP attached */ PORT_CMD_LIST_ON = (1 << 15), /* cmd list DMA engine running */ @@ -178,13 +184,14 @@ enum { AHCI_HFLAG_MV_PATA = (1 << 4), /* PATA port */ AHCI_HFLAG_NO_MSI = (1 << 5), /* no PCI MSI */ AHCI_HFLAG_NO_PMP = (1 << 6), /* no PMP */ + AHCI_HFLAG_NO_HOTPLUG = (1 << 7), /* ignore PxSERR.DIAG.N */ /* ap->flags bits */ - AHCI_FLAG_NO_HOTPLUG = (1 << 24), /* ignore PxSERR.DIAG.N */ AHCI_FLAG_COMMON = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA | - ATA_FLAG_ACPI_SATA | ATA_FLAG_AN, + ATA_FLAG_ACPI_SATA | ATA_FLAG_AN | + ATA_FLAG_IPM, AHCI_LFLAG_COMMON = ATA_LFLAG_SKIP_D2H_BSY, }; @@ -254,6 +261,11 @@ static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg); static int ahci_pci_device_resume(struct pci_dev *pdev); #endif +static struct class_device_attribute *ahci_shost_attrs[] = { + &class_device_attr_link_power_management_policy, + NULL +}; + static struct scsi_host_template ahci_sht = { .module = THIS_MODULE, .name = DRV_NAME, @@ -271,6 +283,7 @@ static struct scsi_host_template ahci_sht = { .slave_configure = ata_scsi_slave_config, .slave_destroy = ata_scsi_slave_destroy, .bios_param = ata_std_bios_param, + .shost_attrs = ahci_shost_attrs, }; static const struct ata_port_operations ahci_ops = { @@ -302,6 +315,8 @@ static const struct ata_port_operations ahci_ops = { .port_suspend = ahci_port_suspend, .port_resume = ahci_port_resume, #endif + .enable_pm = ahci_enable_alpm, + .disable_pm = ahci_disable_alpm, .port_start = ahci_port_start, .port_stop = ahci_port_stop, @@ -836,6 +851,130 @@ static void ahci_power_up(struct ata_port *ap) writel(cmd | PORT_CMD_ICC_ACTIVE, port_mmio + PORT_CMD); } +static void ahci_disable_alpm(struct ata_port *ap) +{ + struct ahci_host_priv *hpriv = ap->host->private_data; + void __iomem *port_mmio = ahci_port_base(ap); + u32 cmd; + struct ahci_port_priv *pp = ap->private_data; + + /* IPM bits should be disabled by libata-core */ + /* get the existing command bits */ + cmd = readl(port_mmio + PORT_CMD); + + /* disable ALPM and ASP */ + cmd &= ~PORT_CMD_ASP; + cmd &= ~PORT_CMD_ALPE; + + /* force the interface back to active */ + cmd |= PORT_CMD_ICC_ACTIVE; + + /* write out new cmd value */ + writel(cmd, port_mmio + PORT_CMD); + cmd = readl(port_mmio + PORT_CMD); + + /* wait 10ms to be sure we've come out of any low power state */ + msleep(10); + + /* clear out any PhyRdy stuff from interrupt status */ + writel(PORT_IRQ_PHYRDY, port_mmio + PORT_IRQ_STAT); + + /* go ahead and clean out PhyRdy Change from Serror too */ + ahci_scr_write(ap, SCR_ERROR, ((1 << 16) | (1 << 18))); + + /* + * Clear flag to indicate that we should ignore all PhyRdy + * state changes + */ + hpriv->flags &= ~AHCI_HFLAG_NO_HOTPLUG; + + /* + * Enable interrupts on Phy Ready. + */ + pp->intr_mask |= PORT_IRQ_PHYRDY; + writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK); + + /* + * don't change the link pm policy - we can be called + * just to turn of link pm temporarily + */ +} + +static int ahci_enable_alpm(struct ata_port *ap, + enum link_pm policy) +{ + struct ahci_host_priv *hpriv = ap->host->private_data; + void __iomem *port_mmio = ahci_port_base(ap); + u32 cmd; + struct ahci_port_priv *pp = ap->private_data; + u32 asp; + + /* Make sure the host is capable of link power management */ + if (!(hpriv->cap & HOST_CAP_ALPM)) + return -EINVAL; + + switch (policy) { + case MAX_PERFORMANCE: + case NOT_AVAILABLE: + /* + * if we came here with NOT_AVAILABLE, + * it just means this is the first time we + * have tried to enable - default to max performance, + * and let the user go to lower power modes on request. + */ + ahci_disable_alpm(ap); + return 0; + case MIN_POWER: + /* configure HBA to enter SLUMBER */ + asp = PORT_CMD_ASP; + break; + case MEDIUM_POWER: + /* configure HBA to enter PARTIAL */ + asp = 0; + break; + default: + return -EINVAL; + } + + /* + * Disable interrupts on Phy Ready. This keeps us from + * getting woken up due to spurious phy ready interrupts + * TBD - Hot plug should be done via polling now, is + * that even supported? + */ + pp->intr_mask &= ~PORT_IRQ_PHYRDY; + writel(pp->intr_mask, port_mmio + PORT_IRQ_MASK); + + /* + * Set a flag to indicate that we should ignore all PhyRdy + * state changes since these can happen now whenever we + * change link state + */ + hpriv->flags |= AHCI_HFLAG_NO_HOTPLUG; + + /* get the existing command bits */ + cmd = readl(port_mmio + PORT_CMD); + + /* + * Set ASP based on Policy + */ + cmd |= asp; + + /* + * Setting this bit will instruct the HBA to aggressively + * enter a lower power link state when it's appropriate and + * based on the value set above for ASP + */ + cmd |= PORT_CMD_ALPE; + + /* write out new cmd value */ + writel(cmd, port_mmio + PORT_CMD); + cmd = readl(port_mmio + PORT_CMD); + + /* IPM bits should be set by libata-core */ + return 0; +} + #ifdef CONFIG_PM static void ahci_power_down(struct ata_port *ap) { @@ -1504,6 +1643,17 @@ static void ahci_port_intr(struct ata_port *ap) if (unlikely(resetting)) status &= ~PORT_IRQ_BAD_PMP; + /* If we are getting PhyRdy, this is + * just a power state change, we should + * clear out this, plus the PhyRdy/Comm + * Wake bits from Serror + */ + if ((hpriv->flags & AHCI_HFLAG_NO_HOTPLUG) && + (status & PORT_IRQ_PHYRDY)) { + status &= ~PORT_IRQ_PHYRDY; + ahci_scr_write(ap, SCR_ERROR, ((1 << 16) | (1 << 18))); + } + if (unlikely(status & PORT_IRQ_ERROR)) { ahci_error_intr(ap, status); return; @@ -2151,6 +2301,9 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) ata_port_pbar_desc(ap, AHCI_PCI_BAR, 0x100 + ap->port_no * 0x80, "port"); + /* set initial link pm policy */ + ap->pm_policy = NOT_AVAILABLE; + /* standard SATA port setup */ if (hpriv->port_map & (1 << i)) ap->ioaddr.cmd_addr = port_mmio; |