summaryrefslogtreecommitdiffstats
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/ide/Kconfig34
-rw-r--r--drivers/ide/Makefile2
-rw-r--r--drivers/ide/cris/Makefile3
-rw-r--r--drivers/ide/cris/ide-cris.c1151
4 files changed, 1 insertions, 1189 deletions
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 3f9e10001e1..f702f9152ce 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -862,40 +862,6 @@ config BLK_DEV_IDE_BAST
Say Y here if you want to support the onboard IDE channels on the
Simtec BAST or the Thorcom VR1000
-config ETRAX_IDE
- tristate "ETRAX IDE support"
- depends on CRIS && BROKEN
- select BLK_DEV_IDEDMA
- help
- Enables the ETRAX IDE driver.
-
- You can't use parallel ports or SCSI ports at the same time.
-
-config ETRAX_IDE_DELAY
- int "Delay for drives to regain consciousness"
- depends on ETRAX_IDE && ETRAX_ARCH_V10
- default 15
- help
- Number of seconds to wait for IDE drives to spin up after an IDE
- reset.
-
-choice
- prompt "IDE reset pin"
- depends on ETRAX_IDE && ETRAX_ARCH_V10
- default ETRAX_IDE_PB7_RESET
-
-config ETRAX_IDE_PB7_RESET
- bool "Port_PB_Bit_7"
- help
- IDE reset on pin 7 on port B
-
-config ETRAX_IDE_G27_RESET
- bool "Port_G_Bit_27"
- help
- IDE reset on pin 27 on port G
-
-endchoice
-
config IDE_H8300
tristate "H8300 IDE support"
depends on H8300
diff --git a/drivers/ide/Makefile b/drivers/ide/Makefile
index 571544c37bb..f94b679b611 100644
--- a/drivers/ide/Makefile
+++ b/drivers/ide/Makefile
@@ -35,7 +35,7 @@ ifeq ($(CONFIG_BLK_DEV_CMD640), y)
obj-y += cmd640-core.o
endif
-obj-$(CONFIG_BLK_DEV_IDE) += cris/ ppc/
+obj-$(CONFIG_BLK_DEV_IDE) += ppc/
obj-$(CONFIG_IDE_H8300) += h8300/
obj-$(CONFIG_IDE_GENERIC) += ide-generic.o
obj-$(CONFIG_BLK_DEV_IDEPNP) += ide-pnp.o
diff --git a/drivers/ide/cris/Makefile b/drivers/ide/cris/Makefile
deleted file mode 100644
index 20b95960531..00000000000
--- a/drivers/ide/cris/Makefile
+++ /dev/null
@@ -1,3 +0,0 @@
-EXTRA_CFLAGS += -Idrivers/ide
-
-obj-$(CONFIG_IDE_ETRAX) += ide-cris.o
diff --git a/drivers/ide/cris/ide-cris.c b/drivers/ide/cris/ide-cris.c
deleted file mode 100644
index 38b069c0057..00000000000
--- a/drivers/ide/cris/ide-cris.c
+++ /dev/null
@@ -1,1151 +0,0 @@
-/*
- * Etrax specific IDE functions, like init and PIO-mode setting etc.
- * Almost the entire ide.c is used for the rest of the Etrax ATA driver.
- * Copyright (c) 2000-2005 Axis Communications AB
- *
- * Authors: Bjorn Wesen (initial version)
- * Mikael Starvik (crisv32 port)
- */
-
-/* Regarding DMA:
- *
- * There are two forms of DMA - "DMA handshaking" between the interface and the drive,
- * and DMA between the memory and the interface. We can ALWAYS use the latter, since it's
- * something built-in in the Etrax. However only some drives support the DMA-mode handshaking
- * on the ATA-bus. The normal PC driver and Triton interface disables memory-if DMA when the
- * device can't do DMA handshaking for some stupid reason. We don't need to do that.
- */
-
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/blkdev.h>
-#include <linux/hdreg.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-
-#include <asm/io.h>
-#include <asm/dma.h>
-
-/* number of DMA descriptors */
-#define MAX_DMA_DESCRS 64
-
-/* number of times to retry busy-flags when reading/writing IDE-registers
- * this can't be too high because a hung harddisk might cause the watchdog
- * to trigger (sometimes INB and OUTB are called with irq's disabled)
- */
-
-#define IDE_REGISTER_TIMEOUT 300
-
-#define LOWDB(x)
-#define D(x)
-
-enum /* Transfer types */
-{
- TYPE_PIO,
- TYPE_DMA,
- TYPE_UDMA
-};
-
-/* CRISv32 specifics */
-#ifdef CONFIG_ETRAX_ARCH_V32
-#include <asm/arch/hwregs/ata_defs.h>
-#include <asm/arch/hwregs/dma_defs.h>
-#include <asm/arch/hwregs/dma.h>
-#include <asm/arch/pinmux.h>
-
-#define ATA_UDMA2_CYC 2
-#define ATA_UDMA2_DVS 3
-#define ATA_UDMA1_CYC 2
-#define ATA_UDMA1_DVS 4
-#define ATA_UDMA0_CYC 4
-#define ATA_UDMA0_DVS 6
-#define ATA_DMA2_STROBE 7
-#define ATA_DMA2_HOLD 1
-#define ATA_DMA1_STROBE 8
-#define ATA_DMA1_HOLD 3
-#define ATA_DMA0_STROBE 25
-#define ATA_DMA0_HOLD 19
-#define ATA_PIO4_SETUP 3
-#define ATA_PIO4_STROBE 7
-#define ATA_PIO4_HOLD 1
-#define ATA_PIO3_SETUP 3
-#define ATA_PIO3_STROBE 9
-#define ATA_PIO3_HOLD 3
-#define ATA_PIO2_SETUP 3
-#define ATA_PIO2_STROBE 13
-#define ATA_PIO2_HOLD 5
-#define ATA_PIO1_SETUP 5
-#define ATA_PIO1_STROBE 23
-#define ATA_PIO1_HOLD 9
-#define ATA_PIO0_SETUP 9
-#define ATA_PIO0_STROBE 39
-#define ATA_PIO0_HOLD 9
-
-int
-cris_ide_ack_intr(ide_hwif_t* hwif)
-{
- reg_ata_rw_ctrl2 ctrl2 = REG_TYPE_CONV(reg_ata_rw_ctrl2, int,
- hwif->io_ports.data_addr);
- REG_WR_INT(ata, regi_ata, rw_ack_intr, 1 << ctrl2.sel);
- return 1;
-}
-
-static inline int
-cris_ide_busy(void)
-{
- reg_ata_rs_stat_data stat_data;
- stat_data = REG_RD(ata, regi_ata, rs_stat_data);
- return stat_data.busy;
-}
-
-static inline int
-cris_ide_ready(void)
-{
- return !cris_ide_busy();
-}
-
-static inline int
-cris_ide_data_available(unsigned short* data)
-{
- reg_ata_rs_stat_data stat_data;
- stat_data = REG_RD(ata, regi_ata, rs_stat_data);
- *data = stat_data.data;
- return stat_data.dav;
-}
-
-static void
-cris_ide_write_command(unsigned long command)
-{
- REG_WR_INT(ata, regi_ata, rw_ctrl2, command); /* write data to the drive's register */
-}
-
-static void
-cris_ide_set_speed(int type, int setup, int strobe, int hold)
-{
- reg_ata_rw_ctrl0 ctrl0 = REG_RD(ata, regi_ata, rw_ctrl0);
- reg_ata_rw_ctrl1 ctrl1 = REG_RD(ata, regi_ata, rw_ctrl1);
-
- if (type == TYPE_PIO) {
- ctrl0.pio_setup = setup;
- ctrl0.pio_strb = strobe;
- ctrl0.pio_hold = hold;
- } else if (type == TYPE_DMA) {
- ctrl0.dma_strb = strobe;
- ctrl0.dma_hold = hold;
- } else if (type == TYPE_UDMA) {
- ctrl1.udma_tcyc = setup;
- ctrl1.udma_tdvs = strobe;
- }
- REG_WR(ata, regi_ata, rw_ctrl0, ctrl0);
- REG_WR(ata, regi_ata, rw_ctrl1, ctrl1);
-}
-
-static unsigned long
-cris_ide_base_address(int bus)
-{
- reg_ata_rw_ctrl2 ctrl2 = {0};
- ctrl2.sel = bus;
- return REG_TYPE_CONV(int, reg_ata_rw_ctrl2, ctrl2);
-}
-
-static unsigned long
-cris_ide_reg_addr(unsigned long addr, int cs0, int cs1)
-{
- reg_ata_rw_ctrl2 ctrl2 = {0};
- ctrl2.addr = addr;
- ctrl2.cs1 = cs1;
- ctrl2.cs0 = cs0;
- return REG_TYPE_CONV(int, reg_ata_rw_ctrl2, ctrl2);
-}
-
-static __init void
-cris_ide_reset(unsigned val)
-{
- reg_ata_rw_ctrl0 ctrl0 = {0};
- ctrl0.rst = val ? regk_ata_active : regk_ata_inactive;
- REG_WR(ata, regi_ata, rw_ctrl0, ctrl0);
-}
-
-static __init void
-cris_ide_init(void)
-{
- reg_ata_rw_ctrl0 ctrl0 = {0};
- reg_ata_rw_intr_mask intr_mask = {0};
-
- ctrl0.en = regk_ata_yes;
- REG_WR(ata, regi_ata, rw_ctrl0, ctrl0);
-
- intr_mask.bus0 = regk_ata_yes;
- intr_mask.bus1 = regk_ata_yes;
- intr_mask.bus2 = regk_ata_yes;
- intr_mask.bus3 = regk_ata_yes;
-
- REG_WR(ata, regi_ata, rw_intr_mask, intr_mask);
-
- crisv32_request_dma(2, "ETRAX FS built-in ATA", DMA_VERBOSE_ON_ERROR, 0, dma_ata);
- crisv32_request_dma(3, "ETRAX FS built-in ATA", DMA_VERBOSE_ON_ERROR, 0, dma_ata);
-
- crisv32_pinmux_alloc_fixed(pinmux_ata);
- crisv32_pinmux_alloc_fixed(pinmux_ata0);
- crisv32_pinmux_alloc_fixed(pinmux_ata1);
- crisv32_pinmux_alloc_fixed(pinmux_ata2);
- crisv32_pinmux_alloc_fixed(pinmux_ata3);
-
- DMA_RESET(regi_dma2);
- DMA_ENABLE(regi_dma2);
- DMA_RESET(regi_dma3);
- DMA_ENABLE(regi_dma3);
-
- DMA_WR_CMD (regi_dma2, regk_dma_set_w_size2);
- DMA_WR_CMD (regi_dma3, regk_dma_set_w_size2);
-}
-
-static dma_descr_context mycontext __attribute__ ((__aligned__(32)));
-
-#define cris_dma_descr_type dma_descr_data
-#define cris_pio_read regk_ata_rd
-#define cris_ultra_mask 0x7
-#define MAX_DESCR_SIZE 0xffffffffUL
-
-static unsigned long
-cris_ide_get_reg(unsigned long reg)
-{
- return (reg & 0x0e000000) >> 25;
-}
-
-static void
-cris_ide_fill_descriptor(cris_dma_descr_type *d, void* buf, unsigned int len, int last)
-{
- d->buf = (char*)virt_to_phys(buf);
- d->after = d->buf + len;
- d->eol = last;
-}
-
-static void
-cris_ide_start_dma(ide_drive_t *drive, cris_dma_descr_type *d, int dir,int type,int len)
-{
- ide_hwif_t *hwif = drive->hwif;
-
- reg_ata_rw_ctrl2 ctrl2 = REG_TYPE_CONV(reg_ata_rw_ctrl2, int,
- hwif->io_ports.data_addr);
- reg_ata_rw_trf_cnt trf_cnt = {0};
-
- mycontext.saved_data = (dma_descr_data*)virt_to_phys(d);
- mycontext.saved_data_buf = d->buf;
- /* start the dma channel */
- DMA_START_CONTEXT(dir ? regi_dma3 : regi_dma2, virt_to_phys(&mycontext));
-
- /* initiate a multi word dma read using PIO handshaking */
- trf_cnt.cnt = len >> 1;
- /* Due to a "feature" the transfer count has to be one extra word for UDMA. */
- if (type == TYPE_UDMA)
- trf_cnt.cnt++;
- REG_WR(ata, regi_ata, rw_trf_cnt, trf_cnt);
-
- ctrl2.rw = dir ? regk_ata_rd : regk_ata_wr;
- ctrl2.trf_mode = regk_ata_dma;
- ctrl2.hsh = type == TYPE_PIO ? regk_ata_pio :
- type == TYPE_DMA ? regk_ata_dma : regk_ata_udma;
- ctrl2.multi = regk_ata_yes;
- ctrl2.dma_size = regk_ata_word;
- REG_WR(ata, regi_ata, rw_ctrl2, ctrl2);
-}
-
-static void
-cris_ide_wait_dma(int dir)
-{
- reg_dma_rw_stat status;
- do
- {
- status = REG_RD(dma, dir ? regi_dma3 : regi_dma2, rw_stat);
- } while(status.list_state != regk_dma_data_at_eol);
-}
-
-static int cris_dma_test_irq(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- int intr = REG_RD_INT(ata, regi_ata, r_intr);
-
- reg_ata_rw_ctrl2 ctrl2 = REG_TYPE_CONV(reg_ata_rw_ctrl2, int,
- hwif->io_ports.data_addr);
-
- return intr & (1 << ctrl2.sel) ? 1 : 0;
-}
-
-static void cris_ide_initialize_dma(int dir)
-{
-}
-
-#else
-/* CRISv10 specifics */
-#include <asm/arch/svinto.h>
-#include <asm/arch/io_interface_mux.h>
-
-/* PIO timing (in R_ATA_CONFIG)
- *
- * _____________________________
- * ADDRESS : ________/
- *
- * _______________
- * DIOR : ____________/ \__________
- *
- * _______________
- * DATA : XXXXXXXXXXXXXXXX_______________XXXXXXXX
- *
- *
- * DIOR is unbuffered while address and data is buffered.
- * This creates two problems:
- * 1. The DIOR pulse is to early (because it is unbuffered)
- * 2. The rise time of DIOR is long
- *
- * There are at least three different plausible solutions
- * 1. Use a pad capable of larger currents in Etrax
- * 2. Use an external buffer
- * 3. Make the strobe pulse longer
- *
- * Some of the strobe timings below are modified to compensate
- * for this. This implies a slight performance decrease.
- *
- * THIS SHOULD NEVER BE CHANGED!
- *
- * TODO: Is this true for the latest LX boards still ?
- */
-
-#define ATA_UDMA2_CYC 0 /* No UDMA supported, just to make it compile. */
-#define ATA_UDMA2_DVS 0
-#define ATA_UDMA1_CYC 0
-#define ATA_UDMA1_DVS 0
-#define ATA_UDMA0_CYC 0
-#define ATA_UDMA0_DVS 0
-#define ATA_DMA2_STROBE 4
-#define ATA_DMA2_HOLD 0
-#define ATA_DMA1_STROBE 4
-#define ATA_DMA1_HOLD 1
-#define ATA_DMA0_STROBE 12
-#define ATA_DMA0_HOLD 9
-#define ATA_PIO4_SETUP 1
-#define ATA_PIO4_STROBE 5
-#define ATA_PIO4_HOLD 0
-#define ATA_PIO3_SETUP 1
-#define ATA_PIO3_STROBE 5
-#define ATA_PIO3_HOLD 1
-#define ATA_PIO2_SETUP 1
-#define ATA_PIO2_STROBE 6
-#define ATA_PIO2_HOLD 2
-#define ATA_PIO1_SETUP 2
-#define ATA_PIO1_STROBE 11
-#define ATA_PIO1_HOLD 4
-#define ATA_PIO0_SETUP 4
-#define ATA_PIO0_STROBE 19
-#define ATA_PIO0_HOLD 4
-
-int
-cris_ide_ack_intr(ide_hwif_t* hwif)
-{
- return 1;
-}
-
-static inline int
-cris_ide_busy(void)
-{
- return *R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy) ;
-}
-
-static inline int
-cris_ide_ready(void)
-{
- return *R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, tr_rdy) ;
-}
-
-static inline int
-cris_ide_data_available(unsigned short* data)
-{
- unsigned long status = *R_ATA_STATUS_DATA;
- *data = (unsigned short)status;
- return status & IO_MASK(R_ATA_STATUS_DATA, dav);
-}
-
-static void
-cris_ide_write_command(unsigned long command)
-{
- *R_ATA_CTRL_DATA = command;
-}
-
-static void
-cris_ide_set_speed(int type, int setup, int strobe, int hold)
-{
- static int pio_setup = ATA_PIO4_SETUP;
- static int pio_strobe = ATA_PIO4_STROBE;
- static int pio_hold = ATA_PIO4_HOLD;
- static int dma_strobe = ATA_DMA2_STROBE;
- static int dma_hold = ATA_DMA2_HOLD;
-
- if (type == TYPE_PIO) {
- pio_setup = setup;
- pio_strobe = strobe;
- pio_hold = hold;
- } else if (type == TYPE_DMA) {
- dma_strobe = strobe;
- dma_hold = hold;
- }
- *R_ATA_CONFIG = ( IO_FIELD( R_ATA_CONFIG, enable, 1 ) |
- IO_FIELD( R_ATA_CONFIG, dma_strobe, dma_strobe ) |
- IO_FIELD( R_ATA_CONFIG, dma_hold, dma_hold ) |
- IO_FIELD( R_ATA_CONFIG, pio_setup, pio_setup ) |
- IO_FIELD( R_ATA_CONFIG, pio_strobe, pio_strobe ) |
- IO_FIELD( R_ATA_CONFIG, pio_hold, pio_hold ) );
-}
-
-static unsigned long
-cris_ide_base_address(int bus)
-{
- return IO_FIELD(R_ATA_CTRL_DATA, sel, bus);
-}
-
-static unsigned long
-cris_ide_reg_addr(unsigned long addr, int cs0, int cs1)
-{
- return IO_FIELD(R_ATA_CTRL_DATA, addr, addr) |
- IO_FIELD(R_ATA_CTRL_DATA, cs0, cs0) |
- IO_FIELD(R_ATA_CTRL_DATA, cs1, cs1);
-}
-
-static __init void
-cris_ide_reset(unsigned val)
-{
-#ifdef CONFIG_ETRAX_IDE_G27_RESET
- REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow, 27, val);
-#endif
-#ifdef CONFIG_ETRAX_IDE_PB7_RESET
- port_pb_dir_shadow = port_pb_dir_shadow |
- IO_STATE(R_PORT_PB_DIR, dir7, output);
- *R_PORT_PB_DIR = port_pb_dir_shadow;
- REG_SHADOW_SET(R_PORT_PB_DATA, port_pb_data_shadow, 7, val);
-#endif
-}
-
-static __init void
-cris_ide_init(void)
-{
- volatile unsigned int dummy;
-
- *R_ATA_CTRL_DATA = 0;
- *R_ATA_TRANSFER_CNT = 0;
- *R_ATA_CONFIG = 0;
-
- if (cris_request_io_interface(if_ata, "ETRAX100LX IDE")) {
- printk(KERN_CRIT "ide: Failed to get IO interface\n");
- return;
- } else if (cris_request_dma(ATA_TX_DMA_NBR,
- "ETRAX100LX IDE TX",
- DMA_VERBOSE_ON_ERROR,
- dma_ata)) {
- cris_free_io_interface(if_ata);
- printk(KERN_CRIT "ide: Failed to get Tx DMA channel\n");
- return;
- } else if (cris_request_dma(ATA_RX_DMA_NBR,
- "ETRAX100LX IDE RX",
- DMA_VERBOSE_ON_ERROR,
- dma_ata)) {
- cris_free_dma(ATA_TX_DMA_NBR, "ETRAX100LX IDE Tx");
- cris_free_io_interface(if_ata);
- printk(KERN_CRIT "ide: Failed to get Rx DMA channel\n");
- return;
- }
-
- /* make a dummy read to set the ata controller in a proper state */
- dummy = *R_ATA_STATUS_DATA;
-
- *R_ATA_CONFIG = ( IO_FIELD( R_ATA_CONFIG, enable, 1 ));
- *R_ATA_CTRL_DATA = ( IO_STATE( R_ATA_CTRL_DATA, rw, read) |
- IO_FIELD( R_ATA_CTRL_DATA, addr, 1 ) );
-
- while(*R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy)); /* wait for busy flag*/
-
- *R_IRQ_MASK0_SET = ( IO_STATE( R_IRQ_MASK0_SET, ata_irq0, set ) |
- IO_STATE( R_IRQ_MASK0_SET, ata_irq1, set ) |
- IO_STATE( R_IRQ_MASK0_SET, ata_irq2, set ) |
- IO_STATE( R_IRQ_MASK0_SET, ata_irq3, set ) );
-
- /* reset the dma channels we will use */
-
- RESET_DMA(ATA_TX_DMA_NBR);
- RESET_DMA(ATA_RX_DMA_NBR);
- WAIT_DMA(ATA_TX_DMA_NBR);
- WAIT_DMA(ATA_RX_DMA_NBR);
-}
-
-#define cris_dma_descr_type etrax_dma_descr
-#define cris_pio_read IO_STATE(R_ATA_CTRL_DATA, rw, read)
-#define cris_ultra_mask 0x0
-#define MAX_DESCR_SIZE 0x10000UL
-
-static unsigned long
-cris_ide_get_reg(unsigned long reg)
-{
- return (reg & 0x0e000000) >> 25;
-}
-
-static void
-cris_ide_fill_descriptor(cris_dma_descr_type *d, void* buf, unsigned int len, int last)
-{
- d->buf = virt_to_phys(buf);
- d->sw_len = len == MAX_DESCR_SIZE ? 0 : len;
- if (last)
- d->ctrl |= d_eol;
-}
-
-static void cris_ide_start_dma(ide_drive_t *drive, cris_dma_descr_type *d, int dir, int type, int len)
-{
- unsigned long cmd;
-
- if (dir) {
- /* need to do this before RX DMA due to a chip bug
- * it is enough to just flush the part of the cache that
- * corresponds to the buffers we start, but since HD transfers
- * usually are more than 8 kB, it is easier to optimize for the
- * normal case and just flush the entire cache. its the only
- * way to be sure! (OB movie quote)
- */
- flush_etrax_cache();
- *R_DMA_CH3_FIRST = virt_to_phys(d);
- *R_DMA_CH3_CMD = IO_STATE(R_DMA_CH3_CMD, cmd, start);
-
- } else {
- *R_DMA_CH2_FIRST = virt_to_phys(d);
- *R_DMA_CH2_CMD = IO_STATE(R_DMA_CH2_CMD, cmd, start);
- }
-
- /* initiate a multi word dma read using DMA handshaking */
-
- *R_ATA_TRANSFER_CNT =
- IO_FIELD(R_ATA_TRANSFER_CNT, count, len >> 1);
-
- cmd = dir ? IO_STATE(R_ATA_CTRL_DATA, rw, read) : IO_STATE(R_ATA_CTRL_DATA, rw, write);
- cmd |= type == TYPE_PIO ? IO_STATE(R_ATA_CTRL_DATA, handsh, pio) :
- IO_STATE(R_ATA_CTRL_DATA, handsh, dma);
- *R_ATA_CTRL_DATA =
- cmd |
- IO_FIELD(R_ATA_CTRL_DATA, data,
- drive->hwif->io_ports.data_addr) |
- IO_STATE(R_ATA_CTRL_DATA, src_dst, dma) |
- IO_STATE(R_ATA_CTRL_DATA, multi, on) |
- IO_STATE(R_ATA_CTRL_DATA, dma_size, word);
-}
-
-static void
-cris_ide_wait_dma(int dir)
-{
- if (dir)
- WAIT_DMA(ATA_RX_DMA_NBR);
- else
- WAIT_DMA(ATA_TX_DMA_NBR);
-}
-
-static int cris_dma_test_irq(ide_drive_t *drive)
-{
- int intr = *R_IRQ_MASK0_RD;
- int bus = IO_EXTRACT(R_ATA_CTRL_DATA, sel,
- drive->hwif->io_ports.data_addr);
-
- return intr & (1 << (bus + IO_BITNR(R_IRQ_MASK0_RD, ata_irq0))) ? 1 : 0;
-}
-
-
-static void cris_ide_initialize_dma(int dir)
-{
- if (dir)
- {
- RESET_DMA(ATA_RX_DMA_NBR); /* sometimes the DMA channel get stuck so we need to do this */
- WAIT_DMA(ATA_RX_DMA_NBR);
- }
- else
- {
- RESET_DMA(ATA_TX_DMA_NBR); /* sometimes the DMA channel get stuck so we need to do this */
- WAIT_DMA(ATA_TX_DMA_NBR);
- }
-}
-
-#endif
-
-void
-cris_ide_outw(unsigned short data, unsigned long reg) {
- int timeleft;
-
- LOWDB(printk("ow: data 0x%x, reg 0x%x\n", data, reg));
-
- /* note the lack of handling any timeouts. we stop waiting, but we don't
- * really notify anybody.
- */
-
- timeleft = IDE_REGISTER_TIMEOUT;
- /* wait for busy flag */
- do {
- timeleft--;
- } while(timeleft && cris_ide_busy());
-
- /*
- * Fall through at a timeout, so the ongoing command will be
- * aborted by the write below, which is expected to be a dummy
- * command to the command register. This happens when a faulty
- * drive times out on a command. See comment on timeout in
- * INB.
- */
- if(!timeleft)
- printk("ATA timeout reg 0x%lx := 0x%x\n", reg, data);
-
- cris_ide_write_command(reg|data); /* write data to the drive's register */
-
- timeleft = IDE_REGISTER_TIMEOUT;
- /* wait for transmitter ready */
- do {
- timeleft--;
- } while(timeleft && !cris_ide_ready());
-}
-
-void
-cris_ide_outb(unsigned char data, unsigned long reg)
-{
- cris_ide_outw(data, reg);
-}
-
-void
-cris_ide_outbsync(ide_drive_t *drive, u8 addr, unsigned long port)
-{
- cris_ide_outw(addr, port);
-}
-
-unsigned short
-cris_ide_inw(unsigned long reg) {
- int timeleft;
- unsigned short val;
-
- timeleft = IDE_REGISTER_TIMEOUT;
- /* wait for busy flag */
- do {
- timeleft--;
- } while(timeleft && cris_ide_busy());
-
- if(!timeleft) {
- /*
- * If we're asked to read the status register, like for
- * example when a command does not complete for an
- * extended time, but the ATA interface is stuck in a
- * busy state at the *ETRAX* ATA interface level (as has
- * happened repeatedly with at least one bad disk), then
- * the best thing to do is to pretend that we read
- * "busy" in the status register, so the IDE driver will
- * time-out, abort the ongoing command and perform a
- * reset sequence. Note that the subsequent OUT_BYTE
- * call will also timeout on busy, but as long as the
- * write is still performed, everything will be fine.
- */
- if (cris_ide_get_reg(reg) == 7)
- return BUSY_STAT;
- else
- /* For other rare cases we assume 0 is good enough. */
- return 0;
- }
-
- cris_ide_write_command(reg | cris_pio_read);
-
- timeleft = IDE_REGISTER_TIMEOUT;
- /* wait for available */
- do {
- timeleft--;
- } while(timeleft && !cris_ide_data_available(&val));
-
- if(!timeleft)
- return 0;
-
- LOWDB(printk("inb: 0x%x from reg 0x%x\n", val & 0xff, reg));
-
- return val;
-}
-
-unsigned char
-cris_ide_inb(unsigned long reg)
-{
- return (unsigned char)cris_ide_inw(reg);
-}
-
-static void cris_input_data(ide_drive_t *, struct request *, void *, unsigned);
-static void cris_output_data(ide_drive_t *, struct request *, void *, unsigned);
-
-static void cris_dma_host_set(ide_drive_t *drive, int on)
-{
-}
-
-static void cris_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
- int setup, strobe, hold;
-
- switch(pio)
- {
- case 0:
- setup = ATA_PIO0_SETUP;
- strobe = ATA_PIO0_STROBE;
- hold = ATA_PIO0_HOLD;
- break;
- case 1:
- setup = ATA_PIO1_SETUP;
- strobe = ATA_PIO1_STROBE;
- hold = ATA_PIO1_HOLD;
- break;
- case 2:
- setup = ATA_PIO2_SETUP;
- strobe = ATA_PIO2_STROBE;
- hold = ATA_PIO2_HOLD;
- break;
- case 3:
- setup = ATA_PIO3_SETUP;
- strobe = ATA_PIO3_STROBE;
- hold = ATA_PIO3_HOLD;
- break;
- case 4:
- setup = ATA_PIO4_SETUP;
- strobe = ATA_PIO4_STROBE;
- hold = ATA_PIO4_HOLD;
- break;
- default:
- return;
- }
-
- cris_ide_set_speed(TYPE_PIO, setup, strobe, hold);
-}
-
-static void cris_set_dma_mode(ide_drive_t *drive, const u8 speed)
-{
- int cyc = 0, dvs = 0, strobe = 0, hold = 0;
-
- switch(speed)
- {
- case XFER_UDMA_0:
- cyc = ATA_UDMA0_CYC;
- dvs = ATA_UDMA0_DVS;
- break;
- case XFER_UDMA_1:
- cyc = ATA_UDMA1_CYC;
- dvs = ATA_UDMA1_DVS;
- break;
- case XFER_UDMA_2:
- cyc = ATA_UDMA2_CYC;
- dvs = ATA_UDMA2_DVS;
- break;
- case XFER_MW_DMA_0:
- strobe = ATA_DMA0_STROBE;
- hold = ATA_DMA0_HOLD;
- break;
- case XFER_MW_DMA_1:
- strobe = ATA_DMA1_STROBE;
- hold = ATA_DMA1_HOLD;
- break;
- case XFER_MW_DMA_2:
- strobe = ATA_DMA2_STROBE;
- hold = ATA_DMA2_HOLD;
- break;
- }
-
- if (speed >= XFER_UDMA_0)
- cris_ide_set_speed(TYPE_UDMA, cyc, dvs, 0);
- else
- cris_ide_set_speed(TYPE_DMA, 0, strobe, hold);
-}
-
-static void __init cris_setup_ports(hw_regs_t *hw, unsigned long base)
-{
- int i;
-
- memset(hw, 0, sizeof(*hw));
-
- for (i = 0; i <= 7; i++)
- hw->io_ports_array[i] = base + cris_ide_reg_addr(i, 0, 1);
-
- /*
- * the IDE control register is at ATA address 6,
- * with CS1 active instead of CS0
- */
- hw->io_ports.ctl_addr = base + cris_ide_reg_addr(6, 1, 0);
-
- hw->irq = ide_default_irq(0);
- hw->ack_intr = cris_ide_ack_intr;
-}
-
-static void cris_tf_load(ide_drive_t *drive, ide_task_t *task)
-{
- struct ide_io_ports *io_ports = &drive->hwif->io_ports;
- struct ide_taskfile *tf = &task->tf;
- u8 HIHI = (task->tf_flags & IDE_TFLAG_LBA48) ? 0xE0 : 0xEF;
-
- if (task->tf_flags & IDE_TFLAG_FLAGGED)
- HIHI = 0xFF;
-
- ide_set_irq(drive, 1);
-
- if (task->tf_flags & IDE_TFLAG_OUT_DATA)
- cris_ide_outw((tf->hob_data << 8) | tf->data,
- io_ports->data_addr);
-
- if (task->tf_flags & IDE_TFLAG_OUT_HOB_FEATURE)
- cris_ide_outb(tf->hob_feature, io_ports->feature_addr);
- if (task->tf_flags & IDE_TFLAG_OUT_HOB_NSECT)
- cris_ide_outb(tf->hob_nsect, io_ports->nsect_addr);
- if (task->tf_flags & IDE_TFLAG_OUT_HOB_LBAL)
- cris_ide_outb(tf->hob_lbal, io_ports->lbal_addr);
- if (task->tf_flags & IDE_TFLAG_OUT_HOB_LBAM)
- cris_ide_outb(tf->hob_lbam, io_ports->lbam_addr);
- if (task->tf_flags & IDE_TFLAG_OUT_HOB_LBAH)
- cris_ide_outb(tf->hob_lbah, io_ports->lbah_addr);
-
- if (task->tf_flags & IDE_TFLAG_OUT_FEATURE)
- cris_ide_outb(tf->feature, io_ports->feature_addr);
- if (task->tf_flags & IDE_TFLAG_OUT_NSECT)
- cris_ide_outb(tf->nsect, io_ports->nsect_addr);
- if (task->tf_flags & IDE_TFLAG_OUT_LBAL)
- cris_ide_outb(tf->lbal, io_ports->lbal_addr);
- if (task->tf_flags & IDE_TFLAG_OUT_LBAM)
- cris_ide_outb(tf->lbam, io_ports->lbam_addr);
- if (task->tf_flags & IDE_TFLAG_OUT_LBAH)
- cris_ide_outb(tf->lbah, io_ports->lbah_addr);
-
- if (task->tf_flags & IDE_TFLAG_OUT_DEVICE)
- cris_ide_outb((tf->device & HIHI) | drive->select.all,
- io_ports->device_addr);
-}
-
-static void cris_tf_read(ide_drive_t *drive, ide_task_t *task)
-{
- struct ide_io_ports *io_ports = &drive->hwif->io_ports;
- struct ide_taskfile *tf = &task->tf;
-
- if (task->tf_flags & IDE_TFLAG_IN_DATA) {
- u16 data = cris_ide_inw(io_ports->data_addr);
-
- tf->data = data & 0xff;
- tf->hob_data = (data >> 8) & 0xff;
- }
-
- /* be sure we're looking at the low order bits */
- cris_ide_outb(drive->ctl & ~0x80, io_ports->ctl_addr);
-
- if (task->tf_flags & IDE_TFLAG_IN_NSECT)
- tf->nsect = cris_ide_inb(io_ports->nsect_addr);
- if (task->tf_flags & IDE_TFLAG_IN_LBAL)
- tf->lbal = cris_ide_inb(io_ports->lbal_addr);
- if (task->tf_flags & IDE_TFLAG_IN_LBAM)
- tf->lbam = cris_ide_inb(io_ports->lbam_addr);
- if (task->tf_flags & IDE_TFLAG_IN_LBAH)
- tf->lbah = cris_ide_inb(io_ports->lbah_addr);
- if (task->tf_flags & IDE_TFLAG_IN_DEVICE)
- tf->device = cris_ide_inb(io_ports->device_addr);
-
- if (task->tf_flags & IDE_TFLAG_LBA48) {
- cris_ide_outb(drive->ctl | 0x80, io_ports->ctl_addr);
-
- if (task->tf_flags & IDE_TFLAG_IN_HOB_FEATURE)
- tf->hob_feature = cris_ide_inb(io_ports->feature_addr);
- if (task->tf_flags & IDE_TFLAG_IN_HOB_NSECT)
- tf->hob_nsect = cris_ide_inb(io_ports->nsect_addr);
- if (task->tf_flags & IDE_TFLAG_IN_HOB_LBAL)
- tf->hob_lbal = cris_ide_inb(io_ports->lbal_addr);
- if (task->tf_flags & IDE_TFLAG_IN_HOB_LBAM)
- tf->hob_lbam = cris_ide_inb(io_ports->lbam_addr);
- if (task->tf_flags & IDE_TFLAG_IN_HOB_LBAH)
- tf->hob_lbah = cris_ide_inb(io_ports->lbah_addr);
- }
-}
-
-static const struct ide_port_ops cris_port_ops = {
- .set_pio_mode = cris_set_pio_mode,
- .set_dma_mode = cris_set_dma_mode,
-};
-
-static const struct ide_dma_ops cris_dma_ops;
-
-static const struct ide_port_info cris_port_info __initdata = {
- .chipset = ide_etrax100,
- .port_ops = &cris_port_ops,
- .dma_ops = &cris_dma_ops,
- .host_flags = IDE_HFLAG_NO_ATAPI_DMA |
- IDE_HFLAG_NO_DMA, /* no SFF-style DMA */
- .pio_mask = ATA_PIO4,
- .udma_mask = cris_ultra_mask,
- .mwdma_mask = ATA_MWDMA2,
-};
-
-static int __init init_e100_ide(void)
-{
- hw_regs_t hw;
- int h;
- u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };
-
- printk("ide: ETRAX FS built-in ATA DMA controller\n");
-
- for (h = 0; h < 4; h++) {
- ide_hwif_t *hwif = NULL;
-
- cris_setup_ports(&hw, cris_ide_base_address(h));
-
- hwif = ide_find_port();
- if (hwif == NULL)
- continue;
- ide_init_port_data(hwif, hwif->index);
- ide_init_port_hw(hwif, &hw);
-
- hwif->tf_load = cris_tf_load;
- hwif->tf_read = cris_tf_read;
-
- hwif->input_data = cris_input_data;
- hwif->output_data = cris_output_data;
-
- hwif->OUTB = &cris_ide_outb;
- hwif->OUTBSYNC = &cris_ide_outbsync;
- hwif->INB = &cris_ide_inb;
- hwif->cbl = ATA_CBL_PATA40;
-
- idx[h] = hwif->index;
- }
-
- /* Reset pulse */
- cris_ide_reset(0);
- udelay(25);
- cris_ide_reset(1);
-
- cris_ide_init();
-
- cris_ide_set_speed(TYPE_PIO, ATA_PIO4_SETUP, ATA_PIO4_STROBE, ATA_PIO4_HOLD);
- cris_ide_set_speed(TYPE_DMA, 0, ATA_DMA2_STROBE, ATA_DMA2_HOLD);
- cris_ide_set_speed(TYPE_UDMA, ATA_UDMA2_CYC, ATA_UDMA2_DVS, 0);
-
- ide_device_add(idx, &cris_port_info);
-
- return 0;
-}
-
-static cris_dma_descr_type mydescr __attribute__ ((__aligned__(16)));
-
-/*
- * This is used for most PIO data transfers *from* the IDE interface
- *
- * These routines will round up any request for an odd number of bytes,
- * so if an odd bytecount is specified, be sure that there's at least one
- * extra byte allocated for the buffer.
- */
-static void cris_input_data(ide_drive_t *drive, struct request *rq,
- void *buffer, unsigned int bytecount)
-{
- D(printk("input_data, buffer 0x%x, count %d\n", buffer, bytecount));
-
- if(bytecount & 1) {
- printk("warning, odd bytecount in cdrom_in_bytes = %d.\n", bytecount);
- bytecount++; /* to round off */
- }
-
- /* setup DMA and start transfer */
-
- cris_ide_fill_descriptor(&mydescr, buffer, bytecount, 1);
- cris_ide_start_dma(drive, &mydescr, 1, TYPE_PIO, bytecount);
-
- /* wait for completion */
- LED_DISK_READ(1);
- cris_ide_wait_dma(1);
- LED_DISK_READ(0);
-}
-
-/*
- * This is used for most PIO data transfers *to* the IDE interface
- */
-static void cris_output_data(ide_drive_t *drive, struct request *rq,
- void *buffer, unsigned int bytecount)
-{
- D(printk("output_data, buffer 0x%x, count %d\n", buffer, bytecount));
-
- if(bytecount & 1) {
- printk("odd bytecount %d in atapi_out_bytes!\n", bytecount);
- bytecount++;
- }
-
- cris_ide_fill_descriptor(&mydescr, buffer, bytecount, 1);
- cris_ide_start_dma(drive, &mydescr, 0, TYPE_PIO, bytecount);
-
- /* wait for completion */
-
- LED_DISK_WRITE(1);
- LED_DISK_READ(1);
- cris_ide_wait_dma(0);
- LED_DISK_WRITE(0);
-}
-
-/* we only have one DMA channel on the chip for ATA, so we can keep these statically */
-static cris_dma_descr_type ata_descrs[MAX_DMA_DESCRS] __attribute__ ((__aligned__(16)));
-static unsigned int ata_tot_size;
-
-/*
- * cris_ide_build_dmatable() prepares a dma request.
- * Returns 0 if all went okay, returns 1 otherwise.
- */
-static int cris_ide_build_dmatable (ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct scatterlist* sg;
- struct request *rq = drive->hwif->hwgroup->rq;
- unsigned long size, addr;
- unsigned int count = 0;
- int i = 0;
-
- sg = hwif->sg_table;
-
- ata_tot_size = 0;
-
- ide_map_sg(drive, rq);
- i = hwif->sg_nents;
-
- while(i) {
- /*
- * Determine addr and size of next buffer area. We assume that
- * individual virtual buffers are always composed linearly in
- * physical memory. For example, we assume that any 8kB buffer
- * is always composed of two adjacent physical 4kB pages rather
- * than two possibly non-adjacent physical 4kB pages.
- */
- /* group sequential buffers into one large buffer */
- addr = sg_phys(sg);
- size = sg_dma_len(sg);
- while (--i) {
- sg = sg_next(sg);
- if ((addr + size) != sg_phys(sg))
- break;
- size += sg_dma_len(sg);
- }
-
- /* did we run out of descriptors? */
-
- if(count >= MAX_DMA_DESCRS) {
- printk("%s: too few DMA descriptors\n", drive->name);
- return 1;
- }
-
- /* however, this case is more difficult - rw_trf_cnt cannot be more
- than 65536 words per transfer, so in that case we need to either
- 1) use a DMA interrupt to re-trigger rw_trf_cnt and continue with
- the descriptors, or
- 2) simply do the request here, and get dma_intr to only ide_end_request on
- those blocks that were actually set-up for transfer.
- */
-
- if(ata_tot_size + size > 131072) {
- printk("too large total ATA DMA request, %d + %d!\n", ata_tot_size, (int)size);
- return 1;
- }
-
- /* If size > MAX_DESCR_SIZE it has to be splitted into new descriptors. Since we
- don't handle size > 131072 only one split is necessary */
-
- if(size > MAX_DESCR_SIZE) {
- cris_ide_fill_descriptor(&ata_descrs[count], (void*)addr, MAX_DESCR_SIZE, 0);
- count++;
- ata_tot_size += MAX_DESCR_SIZE;
- size -= MAX_DESCR_SIZE;
- addr += MAX_DESCR_SIZE;
- }
-
- cris_ide_fill_descriptor(&ata_descrs[count], (void*)addr, size,i ? 0 : 1);
- count++;
- ata_tot_size += size;
- }
-
- if (count) {
- /* return and say all is ok */
- return 0;
- }
-
- printk("%s: empty DMA table?\n", drive->name);
- return 1; /* let the PIO routines handle this weirdness */
-}
-
-/*
- * cris_dma_intr() is the handler for disk read/write DMA interrupts
- */
-static ide_startstop_t cris_dma_intr (ide_drive_t *drive)
-{
- LED_DISK_READ(0);
- LED_DISK_WRITE(0);
-
- return ide_dma_intr(drive);
-}
-
-/*
- * Functions below initiates/aborts DMA read/write operations on a drive.
- *
- * The caller is assumed to have selected the drive and programmed the drive's
- * sector address using CHS or LBA. All that remains is to prepare for DMA
- * and then issue the actual read/write DMA/PIO command to the drive.
- *
- * For ATAPI devices, we just prepare for DMA and return. The caller should
- * then issue the packet command to the drive and call us again with
- * cris_dma_start afterwards.
- *
- * Returns 0 if all went well.
- * Returns 1 if DMA read/write could not be started, in which case
- * the caller should revert to PIO for the current request.
- */
-
-static int cris_dma_end(ide_drive_t *drive)
-{
- drive->waiting_for_dma = 0;
- return 0;
-}
-
-static int cris_dma_setup(ide_drive_t *drive)
-{
- struct request *rq = drive->hwif->hwgroup->rq;
-
- cris_ide_initialize_dma(!rq_data_dir(rq));
- if (cris_ide_build_dmatable (drive)) {
- ide_map_sg(drive, rq);
- return 1;
- }
-
- drive->waiting_for_dma = 1;
- return 0;
-}
-
-static void cris_dma_exec_cmd(ide_drive_t *drive, u8 command)
-{
- ide_execute_command(drive, command, &cris_dma_intr, WAIT_CMD, NULL);
-}
-
-static void cris_dma_start(ide_drive_t *drive)
-{
- struct request *rq = drive->hwif->hwgroup->rq;
- int writing = rq_data_dir(rq);
- int type = TYPE_DMA;
-
- if (drive->current_speed >= XFER_UDMA_0)
- type = TYPE_UDMA;
-
- cris_ide_start_dma(drive, &ata_descrs[0], writing ? 0 : 1, type, ata_tot_size);
-
- if (writing) {
- LED_DISK_WRITE(1);
- } else {
- LED_DISK_READ(1);
- }
-}
-
-static const struct ide_dma_ops cris_dma_ops = {
- .dma_host_set = cris_dma_host_set,
- .dma_setup = cris_dma_setup,
- .dma_exec_cmd = cris_dma_exec_cmd,
- .dma_start = cris_dma_start,
- .dma_end = cris_dma_end,
- .dma_test_irq = cris_dma_test_irq,
-};
-
-module_init(init_e100_ide);
-
-MODULE_LICENSE("GPL");