summaryrefslogtreecommitdiffstats
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/i2c/busses/Kconfig2
-rw-r--r--drivers/i2c/busses/i2c-iop3xx.c16
-rw-r--r--drivers/mmc/at91_mci.c4
-rw-r--r--drivers/net/arm/at91_ether.c2
-rw-r--r--drivers/serial/at91_serial.c2
-rw-r--r--drivers/usb/gadget/at91_udc.c6
-rw-r--r--drivers/video/backlight/locomolcd.c30
7 files changed, 32 insertions, 30 deletions
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 9e56c3989d6..0d9667921f6 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -196,7 +196,7 @@ config I2C_IBM_IIC
config I2C_IOP3XX
tristate "Intel IOP3xx and IXP4xx on-chip I2C interface"
- depends on (ARCH_IOP3XX || ARCH_IXP4XX) && I2C
+ depends on (ARCH_IOP32X || ARCH_IOP33X || ARCH_IXP4XX) && I2C
help
Say Y here if you want to use the IIC bus controller on
the Intel IOP3xx I/O Processors or IXP4xx Network Processors.
diff --git a/drivers/i2c/busses/i2c-iop3xx.c b/drivers/i2c/busses/i2c-iop3xx.c
index 8e413150af3..4436c89be58 100644
--- a/drivers/i2c/busses/i2c-iop3xx.c
+++ b/drivers/i2c/busses/i2c-iop3xx.c
@@ -82,14 +82,16 @@ iop3xx_i2c_enable(struct i2c_algo_iop3xx_data *iop3xx_adap)
/*
* Every time unit enable is asserted, GPOD needs to be cleared
- * on IOP321 to avoid data corruption on the bus.
+ * on IOP3XX to avoid data corruption on the bus.
*/
-#ifdef CONFIG_ARCH_IOP321
-#define IOP321_GPOD_I2C0 0x00c0 /* clear these bits to enable ch0 */
-#define IOP321_GPOD_I2C1 0x0030 /* clear these bits to enable ch1 */
-
- *IOP321_GPOD &= (iop3xx_adap->id == 0) ? ~IOP321_GPOD_I2C0 :
- ~IOP321_GPOD_I2C1;
+#ifdef CONFIG_PLAT_IOP
+ if (iop3xx_adap->id == 0) {
+ gpio_line_set(IOP3XX_GPIO_LINE(7), GPIO_LOW);
+ gpio_line_set(IOP3XX_GPIO_LINE(6), GPIO_LOW);
+ } else {
+ gpio_line_set(IOP3XX_GPIO_LINE(5), GPIO_LOW);
+ gpio_line_set(IOP3XX_GPIO_LINE(4), GPIO_LOW);
+ }
#endif
/* NB SR bits not same position as CR IE bits :-( */
iop3xx_adap->SR_enabled =
diff --git a/drivers/mmc/at91_mci.c b/drivers/mmc/at91_mci.c
index d34b7d9d92e..cb142a66098 100644
--- a/drivers/mmc/at91_mci.c
+++ b/drivers/mmc/at91_mci.c
@@ -851,7 +851,7 @@ static int at91_mci_probe(struct platform_device *pdev)
/*
* Allocate the MCI interrupt
*/
- ret = request_irq(AT91_ID_MCI, at91_mci_irq, IRQF_SHARED, DRIVER_NAME, host);
+ ret = request_irq(AT91RM9200_ID_MCI, at91_mci_irq, IRQF_SHARED, DRIVER_NAME, host);
if (ret) {
printk(KERN_ERR "Failed to request MCI interrupt\n");
clk_disable(mci_clk);
@@ -907,7 +907,7 @@ static int at91_mci_remove(struct platform_device *pdev)
mmc_remove_host(mmc);
at91_mci_disable();
- free_irq(AT91_ID_MCI, host);
+ free_irq(AT91RM9200_ID_MCI, host);
mmc_free_host(mmc);
clk_disable(mci_clk); /* Disable the peripheral clock */
diff --git a/drivers/net/arm/at91_ether.c b/drivers/net/arm/at91_ether.c
index 95b28aa01f4..3ecf2cc53a7 100644
--- a/drivers/net/arm/at91_ether.c
+++ b/drivers/net/arm/at91_ether.c
@@ -947,7 +947,7 @@ static int __init at91ether_setup(unsigned long phy_type, unsigned short phy_add
return -ENOMEM;
dev->base_addr = AT91_VA_BASE_EMAC;
- dev->irq = AT91_ID_EMAC;
+ dev->irq = AT91RM9200_ID_EMAC;
SET_MODULE_OWNER(dev);
/* Install the interrupt handler */
diff --git a/drivers/serial/at91_serial.c b/drivers/serial/at91_serial.c
index 54c6b2adf7b..bf4bf103e5a 100644
--- a/drivers/serial/at91_serial.c
+++ b/drivers/serial/at91_serial.c
@@ -139,7 +139,7 @@ static void at91_set_mctrl(struct uart_port *port, u_int mctrl)
* AT91RM9200 Errata #39: RTS0 is not internally connected to PA21.
* We need to drive the pin manually.
*/
- if (port->mapbase == AT91_BASE_US0) {
+ if (port->mapbase == AT91RM9200_BASE_US0) {
if (mctrl & TIOCM_RTS)
at91_set_gpio_value(AT91_PIN_PA21, 0);
else
diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c
index d00958a01cf..77beba485a8 100644
--- a/drivers/usb/gadget/at91_udc.c
+++ b/drivers/usb/gadget/at91_udc.c
@@ -1658,7 +1658,7 @@ static int __devinit at91udc_probe(struct platform_device *pdev)
return -ENODEV;
}
- if (!request_mem_region(AT91_BASE_UDP, SZ_16K, driver_name)) {
+ if (!request_mem_region(AT91RM9200_BASE_UDP, SZ_16K, driver_name)) {
DBG("someone's using UDC memory\n");
return -EBUSY;
}
@@ -1720,7 +1720,7 @@ static int __devinit at91udc_probe(struct platform_device *pdev)
fail1:
device_unregister(&udc->gadget.dev);
fail0:
- release_mem_region(AT91_BASE_UDP, SZ_16K);
+ release_mem_region(AT91RM9200_BASE_UDP, SZ_16K);
DBG("%s probe failed, %d\n", driver_name, retval);
return retval;
}
@@ -1742,7 +1742,7 @@ static int __devexit at91udc_remove(struct platform_device *pdev)
free_irq(udc->board.vbus_pin, udc);
free_irq(udc->udp_irq, udc);
device_unregister(&udc->gadget.dev);
- release_mem_region(AT91_BASE_UDP, SZ_16K);
+ release_mem_region(AT91RM9200_BASE_UDP, SZ_16K);
clk_put(udc->iclk);
clk_put(udc->fclk);
diff --git a/drivers/video/backlight/locomolcd.c b/drivers/video/backlight/locomolcd.c
index caf1eca199b..628571c63ba 100644
--- a/drivers/video/backlight/locomolcd.c
+++ b/drivers/video/backlight/locomolcd.c
@@ -33,19 +33,19 @@ static unsigned long locomolcd_flags;
static void locomolcd_on(int comadj)
{
- locomo_gpio_set_dir(locomolcd_dev, LOCOMO_GPIO_LCD_VSHA_ON, 0);
- locomo_gpio_write(locomolcd_dev, LOCOMO_GPIO_LCD_VSHA_ON, 1);
+ locomo_gpio_set_dir(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VSHA_ON, 0);
+ locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VSHA_ON, 1);
mdelay(2);
- locomo_gpio_set_dir(locomolcd_dev, LOCOMO_GPIO_LCD_VSHD_ON, 0);
- locomo_gpio_write(locomolcd_dev, LOCOMO_GPIO_LCD_VSHD_ON, 1);
+ locomo_gpio_set_dir(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VSHD_ON, 0);
+ locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VSHD_ON, 1);
mdelay(2);
locomo_m62332_senddata(locomolcd_dev, comadj, 0);
mdelay(5);
- locomo_gpio_set_dir(locomolcd_dev, LOCOMO_GPIO_LCD_VEE_ON, 0);
- locomo_gpio_write(locomolcd_dev, LOCOMO_GPIO_LCD_VEE_ON, 1);
+ locomo_gpio_set_dir(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VEE_ON, 0);
+ locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VEE_ON, 1);
mdelay(10);
/* TFTCRST | CPSOUT=0 | CPSEN */
@@ -58,8 +58,8 @@ static void locomolcd_on(int comadj)
locomo_writel((0x04 | 0x01), locomolcd_dev->mapbase + LOCOMO_TC);
mdelay(10);
- locomo_gpio_set_dir(locomolcd_dev, LOCOMO_GPIO_LCD_MOD, 0);
- locomo_gpio_write(locomolcd_dev, LOCOMO_GPIO_LCD_MOD, 1);
+ locomo_gpio_set_dir(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_MOD, 0);
+ locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_MOD, 1);
}
static void locomolcd_off(int comadj)
@@ -68,16 +68,16 @@ static void locomolcd_off(int comadj)
locomo_writel(0x06, locomolcd_dev->mapbase + LOCOMO_TC);
mdelay(1);
- locomo_gpio_write(locomolcd_dev, LOCOMO_GPIO_LCD_VSHA_ON, 0);
+ locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VSHA_ON, 0);
mdelay(110);
- locomo_gpio_write(locomolcd_dev, LOCOMO_GPIO_LCD_VEE_ON, 0);
+ locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VEE_ON, 0);
mdelay(700);
/* TFTCRST=0 | CPSOUT=0 | CPSEN = 0 */
locomo_writel(0, locomolcd_dev->mapbase + LOCOMO_TC);
- locomo_gpio_write(locomolcd_dev, LOCOMO_GPIO_LCD_MOD, 0);
- locomo_gpio_write(locomolcd_dev, LOCOMO_GPIO_LCD_VSHD_ON, 0);
+ locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_MOD, 0);
+ locomo_gpio_write(locomolcd_dev->dev.parent, LOCOMO_GPIO_LCD_VSHD_ON, 0);
}
void locomolcd_power(int on)
@@ -167,14 +167,14 @@ static int locomolcd_resume(struct locomo_dev *dev)
#define locomolcd_resume NULL
#endif
-static int locomolcd_probe(struct locomo_dev *dev)
+static int locomolcd_probe(struct locomo_dev *ldev)
{
unsigned long flags;
local_irq_save(flags);
- locomolcd_dev = dev;
+ locomolcd_dev = ldev;
- locomo_gpio_set_dir(dev, LOCOMO_GPIO_FL_VR, 0);
+ locomo_gpio_set_dir(ldev->dev.parent, LOCOMO_GPIO_FL_VR, 0);
/* the poodle_lcd_power function is called for the first time
* from fs_initcall, which is before locomo is activated.
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-11 11:38:25 +0000