diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/power/Kconfig | 2 | ||||
| -rw-r--r-- | drivers/power/Makefile | 1 | ||||
| -rw-r--r-- | drivers/power/avs/Kconfig | 12 | ||||
| -rw-r--r-- | drivers/power/avs/Makefile | 1 | ||||
| -rw-r--r-- | drivers/power/avs/smartreflex.c | 1126 |
5 files changed, 1142 insertions, 0 deletions
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index 99dc29f2f2f..d416773771e 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -308,3 +308,5 @@ config AB8500_BATTERY_THERM_ON_BATCTRL Say Y to enable battery temperature measurements using thermistor connected on BATCTRL ADC. endif # POWER_SUPPLY + +source "drivers/power/avs/Kconfig" diff --git a/drivers/power/Makefile b/drivers/power/Makefile index b6b243416c0..ee58afb1e71 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -43,4 +43,5 @@ obj-$(CONFIG_CHARGER_GPIO) += gpio-charger.o obj-$(CONFIG_CHARGER_MANAGER) += charger-manager.o obj-$(CONFIG_CHARGER_MAX8997) += max8997_charger.o obj-$(CONFIG_CHARGER_MAX8998) += max8998_charger.o +obj-$(CONFIG_POWER_AVS) += avs/ obj-$(CONFIG_CHARGER_SMB347) += smb347-charger.o diff --git a/drivers/power/avs/Kconfig b/drivers/power/avs/Kconfig new file mode 100644 index 00000000000..18493f7a8f6 --- /dev/null +++ b/drivers/power/avs/Kconfig @@ -0,0 +1,12 @@ +menuconfig POWER_AVS + tristate "Adaptive Voltage Scaling class support" + help + AVS is a power management technique which finely controls the + operating voltage of a device in order to optimize (i.e. reduce) + its power consumption. + At a given operating point the voltage is adapted depending on + static factors (chip manufacturing process) and dynamic factors + (temperature depending performance). + AVS is also called SmartReflex on OMAP devices. + + Say Y here to enable Adaptive Voltage Scaling class support. diff --git a/drivers/power/avs/Makefile b/drivers/power/avs/Makefile new file mode 100644 index 00000000000..0843386a6c1 --- /dev/null +++ b/drivers/power/avs/Makefile @@ -0,0 +1 @@ +obj-$(CONFIG_POWER_AVS_OMAP) += smartreflex.o diff --git a/drivers/power/avs/smartreflex.c b/drivers/power/avs/smartreflex.c new file mode 100644 index 00000000000..44efc6e202a --- /dev/null +++ b/drivers/power/avs/smartreflex.c @@ -0,0 +1,1126 @@ +/* + * OMAP SmartReflex Voltage Control + * + * Author: Thara Gopinath <thara@ti.com> + * + * Copyright (C) 2012 Texas Instruments, Inc. + * Thara Gopinath <thara@ti.com> + * + * Copyright (C) 2008 Nokia Corporation + * Kalle Jokiniemi + * + * Copyright (C) 2007 Texas Instruments, Inc. + * Lesly A M <x0080970@ti.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/debugfs.h> +#include <linux/delay.h> +#include <linux/slab.h> +#include <linux/pm_runtime.h> +#include <linux/power/smartreflex.h> + +#define SMARTREFLEX_NAME_LEN 16 +#define NVALUE_NAME_LEN 40 +#define SR_DISABLE_TIMEOUT 200 + +/* sr_list contains all the instances of smartreflex module */ +static LIST_HEAD(sr_list); + +static struct omap_sr_class_data *sr_class; +static struct omap_sr_pmic_data *sr_pmic_data; +static struct dentry *sr_dbg_dir; + +static inline void sr_write_reg(struct omap_sr *sr, unsigned offset, u32 value) +{ + __raw_writel(value, (sr->base + offset)); +} + +static inline void sr_modify_reg(struct omap_sr *sr, unsigned offset, u32 mask, + u32 value) +{ + u32 reg_val; + + /* + * Smartreflex error config register is special as it contains + * certain status bits which if written a 1 into means a clear + * of those bits. So in order to make sure no accidental write of + * 1 happens to those status bits, do a clear of them in the read + * value. This mean this API doesn't rewrite values in these bits + * if they are currently set, but does allow the caller to write + * those bits. + */ + if (sr->ip_type == SR_TYPE_V1 && offset == ERRCONFIG_V1) + mask |= ERRCONFIG_STATUS_V1_MASK; + else if (sr->ip_type == SR_TYPE_V2 && offset == ERRCONFIG_V2) + mask |= ERRCONFIG_VPBOUNDINTST_V2; + + reg_val = __raw_readl(sr->base + offset); + reg_val &= ~mask; + + value &= mask; + + reg_val |= value; + + __raw_writel(reg_val, (sr->base + offset)); +} + +static inline u32 sr_read_reg(struct omap_sr *sr, unsigned offset) +{ + return __raw_readl(sr->base + offset); +} + +static struct omap_sr *_sr_lookup(struct voltagedomain *voltdm) +{ + struct omap_sr *sr_info; + + if (!voltdm) { + pr_err("%s: Null voltage domain passed!\n", __func__); + return ERR_PTR(-EINVAL); + } + + list_for_each_entry(sr_info, &sr_list, node) { + if (voltdm == sr_info->voltdm) + return sr_info; + } + + return ERR_PTR(-ENODATA); +} + +static irqreturn_t sr_interrupt(int irq, void *data) +{ + struct omap_sr *sr_info = data; + u32 status = 0; + + switch (sr_info->ip_type) { + case SR_TYPE_V1: + /* Read the status bits */ + status = sr_read_reg(sr_info, ERRCONFIG_V1); + + /* Clear them by writing back */ + sr_write_reg(sr_info, ERRCONFIG_V1, status); + break; + case SR_TYPE_V2: + /* Read the status bits */ + status = sr_read_reg(sr_info, IRQSTATUS); + + /* Clear them by writing back */ + sr_write_reg(sr_info, IRQSTATUS, status); + break; + default: + dev_err(&sr_info->pdev->dev, "UNKNOWN IP type %d\n", + sr_info->ip_type); + return IRQ_NONE; + } + + if (sr_class->notify) + sr_class->notify(sr_info, status); + + return IRQ_HANDLED; +} + +static void sr_set_clk_length(struct omap_sr *sr) +{ + struct clk *sys_ck; + u32 sys_clk_speed; + + if (cpu_is_omap34xx()) + sys_ck = clk_get(NULL, "sys_ck"); + else + sys_ck = clk_get(NULL, "sys_clkin_ck"); + + if (IS_ERR(sys_ck)) { + dev_err(&sr->pdev->dev, "%s: unable to get sys clk\n", + __func__); + return; + } + + sys_clk_speed = clk_get_rate(sys_ck); + clk_put(sys_ck); + + switch (sys_clk_speed) { + case 12000000: + sr->clk_length = SRCLKLENGTH_12MHZ_SYSCLK; + break; + case 13000000: + sr->clk_length = SRCLKLENGTH_13MHZ_SYSCLK; + break; + case 19200000: + sr->clk_length = SRCLKLENGTH_19MHZ_SYSCLK; + break; + case 26000000: + sr->clk_length = SRCLKLENGTH_26MHZ_SYSCLK; + break; + case 38400000: + sr->clk_length = SRCLKLENGTH_38MHZ_SYSCLK; + break; + default: + dev_err(&sr->pdev->dev, "%s: Invalid sysclk value: %d\n", + __func__, sys_clk_speed); + break; + } +} + +static void sr_set_regfields(struct omap_sr *sr) +{ + /* + * For time being these values are defined in smartreflex.h + * and populated during init. May be they can be moved to board + * file or pmic specific data structure. In that case these structure + * fields will have to be populated using the pdata or pmic structure. + */ + if (cpu_is_omap34xx() || cpu_is_omap44xx()) { + sr->err_weight = OMAP3430_SR_ERRWEIGHT; + sr->err_maxlimit = OMAP3430_SR_ERRMAXLIMIT; + sr->accum_data = OMAP3430_SR_ACCUMDATA; + if (!(strcmp(sr->name, "smartreflex_mpu_iva"))) { + sr->senn_avgweight = OMAP3430_SR1_SENNAVGWEIGHT; + sr->senp_avgweight = OMAP3430_SR1_SENPAVGWEIGHT; + } else { + sr->senn_avgweight = OMAP3430_SR2_SENNAVGWEIGHT; + sr->senp_avgweight = OMAP3430_SR2_SENPAVGWEIGHT; + } + } +} + +static void sr_start_vddautocomp(struct omap_sr *sr) +{ + if (!sr_class || !(sr_class->enable) || !(sr_class->configure)) { + dev_warn(&sr->pdev->dev, + "%s: smartreflex class driver not registered\n", + __func__); + return; + } + + if (!sr_class->enable(sr)) + sr->autocomp_active = true; +} + +static void sr_stop_vddautocomp(struct omap_sr *sr) +{ + if (!sr_class || !(sr_class->disable)) { + dev_warn(&sr->pdev->dev, + "%s: smartreflex class driver not registered\n", + __func__); + return; + } + + if (sr->autocomp_active) { + sr_class->disable(sr, 1); + sr->autocomp_active = false; + } +} + +/* + * This function handles the intializations which have to be done + * only when both sr device and class driver regiter has + * completed. This will be attempted to be called from both sr class + * driver register and sr device intializtion API's. Only one call + * will ultimately succeed. + * + * Currently this function registers interrupt handler for a particular SR + * if smartreflex class driver is already registered and has + * requested for interrupts and the SR interrupt line in present. + */ +static int sr_late_init(struct omap_sr *sr_info) +{ + struct omap_sr_data *pdata = sr_info->pdev->dev.platform_data; + struct resource *mem; + int ret = 0; + + if (sr_class->notify && sr_class->notify_flags && sr_info->irq) { + ret = request_irq(sr_info->irq, sr_interrupt, + 0, sr_info->name, sr_info); + if (ret) + goto error; + disable_irq(sr_info->irq); + } + + if (pdata && pdata->enable_on_init) + sr_start_vddautocomp(sr_info); + + return ret; + +error: + iounmap(sr_info->base); + mem = platform_get_resource(sr_info->pdev, IORESOURCE_MEM, 0); + release_mem_region(mem->start, resource_size(mem)); + list_del(&sr_info->node); + dev_err(&sr_info->pdev->dev, "%s: ERROR in registering" + "interrupt handler. Smartreflex will" + "not function as desired\n", __func__); + kfree(sr_info); + + return ret; +} + +static void sr_v1_disable(struct omap_sr *sr) +{ + int timeout = 0; + int errconf_val = ERRCONFIG_MCUACCUMINTST | ERRCONFIG_MCUVALIDINTST | + ERRCONFIG_MCUBOUNDINTST; + + /* Enable MCUDisableAcknowledge interrupt */ + sr_modify_reg(sr, ERRCONFIG_V1, + ERRCONFIG_MCUDISACKINTEN, ERRCONFIG_MCUDISACKINTEN); + + /* SRCONFIG - disable SR */ + sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, 0x0); + + /* Disable all other SR interrupts and clear the status as needed */ + if (sr_read_reg(sr, ERRCONFIG_V1) & ERRCONFIG_VPBOUNDINTST_V1) + errconf_val |= ERRCONFIG_VPBOUNDINTST_V1; + sr_modify_reg(sr, ERRCONFIG_V1, + (ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUVALIDINTEN | + ERRCONFIG_MCUBOUNDINTEN | ERRCONFIG_VPBOUNDINTEN_V1), + errconf_val); + + /* + * Wait for SR to be disabled. + * wait until ERRCONFIG.MCUDISACKINTST = 1. Typical latency is 1us. + */ + sr_test_cond_timeout((sr_read_reg(sr, ERRCONFIG_V1) & + ERRCONFIG_MCUDISACKINTST), SR_DISABLE_TIMEOUT, + timeout); + + if (timeout >= SR_DISABLE_TIMEOUT) + dev_warn(&sr->pdev->dev, "%s: Smartreflex disable timedout\n", + __func__); + + /* Disable MCUDisableAcknowledge interrupt & clear pending interrupt */ + sr_modify_reg(sr, ERRCONFIG_V1, ERRCONFIG_MCUDISACKINTEN, + ERRCONFIG_MCUDISACKINTST); +} + +static void sr_v2_disable(struct omap_sr *sr) +{ + int timeout = 0; + + /* Enable MCUDisableAcknowledge interrupt */ + sr_write_reg(sr, IRQENABLE_SET, IRQENABLE_MCUDISABLEACKINT); + + /* SRCONFIG - disable SR */ + sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, 0x0); + + /* + * Disable all other SR interrupts and clear the status + * write to status register ONLY on need basis - only if status + * is set. + */ + if (sr_read_reg(sr, ERRCONFIG_V2) & ERRCONFIG_VPBOUNDINTST_V2) + sr_modify_reg(sr, ERRCONFIG_V2, ERRCONFIG_VPBOUNDINTEN_V2, + ERRCONFIG_VPBOUNDINTST_V2); + else + sr_modify_reg(sr, ERRCONFIG_V2, ERRCONFIG_VPBOUNDINTEN_V2, + 0x0); + sr_write_reg(sr, IRQENABLE_CLR, (IRQENABLE_MCUACCUMINT | + IRQENABLE_MCUVALIDINT | + IRQENABLE_MCUBOUNDSINT)); + sr_write_reg(sr, IRQSTATUS, (IRQSTATUS_MCUACCUMINT | + IRQSTATUS_MCVALIDINT | + IRQSTATUS_MCBOUNDSINT)); + + /* + * Wait for SR to be disabled. + * wait until IRQSTATUS.MCUDISACKINTST = 1. Typical latency is 1us. + */ + sr_test_cond_timeout((sr_read_reg(sr, IRQSTATUS) & + IRQSTATUS_MCUDISABLEACKINT), SR_DISABLE_TIMEOUT, + timeout); + + if (timeout >= SR_DISABLE_TIMEOUT) + dev_warn(&sr->pdev->dev, "%s: Smartreflex disable timedout\n", + __func__); + + /* Disable MCUDisableAcknowledge interrupt & clear pending interrupt */ + sr_write_reg(sr, IRQENABLE_CLR, IRQENABLE_MCUDISABLEACKINT); + sr_write_reg(sr, IRQSTATUS, IRQSTATUS_MCUDISABLEACKINT); +} + +static struct omap_sr_nvalue_table *sr_retrieve_nvalue_row( + struct omap_sr *sr, u32 efuse_offs) +{ + int i; + + if (!sr->nvalue_table) { + dev_warn(&sr->pdev->dev, "%s: Missing ntarget value table\n", + __func__); + return NULL; + } + + for (i = 0; i < sr->nvalue_count; i++) { + if (sr->nvalue_table[i].efuse_offs == efuse_offs) + return &sr->nvalue_table[i]; + } + + return NULL; +} + +/* Public Functions */ + +/** + * sr_configure_errgen() - Configures the smrtreflex to perform AVS using the + * error generator module. + * @voltdm: VDD pointer to which the SR module to be configured belongs to. + * + * This API is to be called from the smartreflex class driver to + * configure the error generator module inside the smartreflex module. + * SR settings if using the ERROR module inside Smartreflex. + * SR CLASS 3 by default uses only the ERROR module where as + * SR CLASS 2 can choose between ERROR module and MINMAXAVG + * module. Returns 0 on success and error value in case of failure. + */ +int sr_configure_errgen(struct voltagedomain *voltdm) +{ + u32 sr_config, sr_errconfig, errconfig_offs; + u32 vpboundint_en, vpboundint_st; + u32 senp_en = 0, senn_en = 0; + u8 senp_shift, senn_shift; + struct omap_sr *sr = _sr_lookup(voltdm); + + if (IS_ERR(sr)) { + pr_warning("%s: omap_sr struct for voltdm not found\n", __func__); + return PTR_ERR(sr); + } + + if (!sr->clk_length) + sr_set_clk_length(sr); + + senp_en = sr->senp_mod; + senn_en = sr->senn_mod; + + sr_config = (sr->clk_length << SRCONFIG_SRCLKLENGTH_SHIFT) | + SRCONFIG_SENENABLE | SRCONFIG_ERRGEN_EN; + + switch (sr->ip_type) { + case SR_TYPE_V1: + sr_config |= SRCONFIG_DELAYCTRL; + senn_shift = SRCONFIG_SENNENABLE_V1_SHIFT; + senp_shift = SRCONFIG_SENPENABLE_V1_SHIFT; + errconfig_offs = ERRCONFIG_V1; + vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V1; + vpboundint_st = ERRCONFIG_VPBOUNDINTST_V1; + break; + case SR_TYPE_V2: + senn_shift = SRCONFIG_SENNENABLE_V2_SHIFT; + senp_shift = SRCONFIG_SENPENABLE_V2_SHIFT; + errconfig_offs = ERRCONFIG_V2; + vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V2; + vpboundint_st = ERRCONFIG_VPBOUNDINTST_V2; + break; + default: + dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex" + "module without specifying the ip\n", __func__); + return -EINVAL; + } + + sr_config |= ((senn_en << senn_shift) | (senp_en << senp_shift)); + sr_write_reg(sr, SRCONFIG, sr_config); + sr_errconfig = (sr->err_weight << ERRCONFIG_ERRWEIGHT_SHIFT) | + (sr->err_maxlimit << ERRCONFIG_ERRMAXLIMIT_SHIFT) | + (sr->err_minlimit << ERRCONFIG_ERRMINLIMIT_SHIFT); + sr_modify_reg(sr, errconfig_offs, (SR_ERRWEIGHT_MASK | + SR_ERRMAXLIMIT_MASK | SR_ERRMINLIMIT_MASK), + sr_errconfig); + + /* Enabling the interrupts if the ERROR module is used */ + sr_modify_reg(sr, errconfig_offs, (vpboundint_en | vpboundint_st), + vpboundint_en); + + return 0; +} + +/** + * sr_disable_errgen() - Disables SmartReflex AVS module's errgen component + * @voltdm: VDD pointer to which the SR module to be configured belongs to. + * + * This API is to be called from the smartreflex class driver to + * disable the error generator module inside the smartreflex module. + * + * Returns 0 on success and error value in case of failure. + */ +int sr_disable_errgen(struct voltagedomain *voltdm) +{ + u32 errconfig_offs; + u32 vpboundint_en, vpboundint_st; + struct omap_sr *sr = _sr_lookup(voltdm); + + if (IS_ERR(sr)) { + pr_warning("%s: omap_sr struct for voltdm not found\n", __func__); + return PTR_ERR(sr); + } + + switch (sr->ip_type) { + case SR_TYPE_V1: + errconfig_offs = ERRCONFIG_V1; + vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V1; + vpboundint_st = ERRCONFIG_VPBOUNDINTST_V1; + break; + case SR_TYPE_V2: + errconfig_offs = ERRCONFIG_V2; + vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V2; + vpboundint_st = ERRCONFIG_VPBOUNDINTST_V2; + break; + default: + dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex" + "module without specifying the ip\n", __func__); + return -EINVAL; + } + + /* Disable the interrupts of ERROR module */ + sr_modify_reg(sr, errconfig_offs, vpboundint_en | vpboundint_st, 0); + + /* Disable the Sensor and errorgen */ + sr_modify_reg(sr, SRCONFIG, SRCONFIG_SENENABLE | SRCONFIG_ERRGEN_EN, 0); + + return 0; +} + +/** + * sr_configure_minmax() - Configures the smrtreflex to perform AVS using the + * minmaxavg module. + * @voltdm: VDD pointer to which the SR module to be configured belongs to. + * + * This API is to be called from the smartreflex class driver to + * configure the minmaxavg module inside the smartreflex module. + * SR settings if using the ERROR module inside Smartreflex. + * SR CLASS 3 by default uses only the ERROR module where as + * SR CLASS 2 can choose between ERROR module and MINMAXAVG + * module. Returns 0 on success and error value in case of failure. + */ +int sr_configure_minmax(struct voltagedomain *voltdm) +{ + u32 sr_config, sr_avgwt; + u32 senp_en = 0, senn_en = 0; + u8 senp_shift, senn_shift; + struct omap_sr *sr = _sr_lookup(voltdm); + + if (IS_ERR(sr)) { + pr_warning("%s: omap_sr struct for voltdm not found\n", __func__); + return PTR_ERR(sr); + } + + if (!sr->clk_length) + sr_set_clk_length(sr); + + senp_en = sr->senp_mod; + senn_en = sr->senn_mod; + + sr_config = (sr->clk_length << SRCONFIG_SRCLKLENGTH_SHIFT) | + SRCONFIG_SENENABLE | + (sr->accum_data << SRCONFIG_ACCUMDATA_SHIFT); + + switch (sr->ip_type) { + case SR_TYPE_V1: + sr_config |= SRCONFIG_DELAYCTRL; + senn_shift = SRCONFIG_SENNENABLE_V1_SHIFT; + senp_shift = SRCONFIG_SENPENABLE_V1_SHIFT; + break; + case SR_TYPE_V2: + senn_shift = SRCONFIG_SENNENABLE_V2_SHIFT; + senp_shift = SRCONFIG_SENPENABLE_V2_SHIFT; + break; + default: + dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex" + "module without specifying the ip\n", __func__); + return -EINVAL; + } + + sr_config |= ((senn_en << senn_shift) | (senp_en << senp_shift)); + sr_write_reg(sr, SRCONFIG, sr_config); + sr_avgwt = (sr->senp_avgweight << AVGWEIGHT_SENPAVGWEIGHT_SHIFT) | + (sr->senn_avgweight << AVGWEIGHT_SENNAVGWEIGHT_SHIFT); + sr_write_reg(sr, AVGWEIGHT, sr_avgwt); + + /* + * Enabling the interrupts if MINMAXAVG module is used. + * TODO: check if all the interrupts are mandatory + */ + switch (sr->ip_type) { + case SR_TYPE_V1: + sr_modify_reg(sr, ERRCONFIG_V1, + (ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUVALIDINTEN | + ERRCONFIG_MCUBOUNDINTEN), + (ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUACCUMINTST | + ERRCONFIG_MCUVALIDINTEN | ERRCONFIG_MCUVALIDINTST | + ERRCONFIG_MCUBOUNDINTEN | ERRCONFIG_MCUBOUNDINTST)); + break; + case SR_TYPE_V2: + sr_write_reg(sr, IRQSTATUS, + IRQSTATUS_MCUACCUMINT | IRQSTATUS_MCVALIDINT | + IRQSTATUS_MCBOUNDSINT | IRQSTATUS_MCUDISABLEACKINT); + sr_write_reg(sr, IRQENABLE_SET, + IRQENABLE_MCUACCUMINT | IRQENABLE_MCUVALIDINT | + IRQENABLE_MCUBOUNDSINT | IRQENABLE_MCUDISABLEACKINT); + break; + default: + dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex" + "module without specifying the ip\n", __func__); + return -EINVAL; + } + + return 0; +} + +/** + * sr_enable() - Enables the smartreflex module. + * @voltdm: VDD pointer to which the SR module to be configured belongs to. + * @volt: The voltage at which the Voltage domain associated with + * the smartreflex module is operating at. + * This is required only to program the correct Ntarget value. + * + * This API is to be called from the smartreflex class driver to + * enable a smartreflex module. Returns 0 on success. Returns error + * value if the voltage passed is wrong or if ntarget value is wrong. + */ +int sr_enable(struct voltagedomain *voltdm, unsigned long volt) +{ + struct omap_volt_data *volt_data; + struct omap_sr *sr = _sr_lookup(voltdm); + struct omap_sr_nvalue_table *nvalue_row; + int ret; + + if (IS_ERR(sr)) { + pr_warning("%s: omap_sr struct for voltdm not found\n", __func__); + return PTR_ERR(sr); + } + + volt_data = omap_voltage_get_voltdata(sr->voltdm, volt); + + if (IS_ERR(volt_data)) { + dev_warn(&sr->pdev->dev, "%s: Unable to get voltage table" + "for nominal voltage %ld\n", __func__, volt); + return PTR_ERR(volt_data); + } + + nvalue_row = sr_retrieve_nvalue_row(sr, volt_data->sr_efuse_offs); + + if (!nvalue_row) { + dev_warn(&sr->pdev->dev, "%s: failure getting SR data for this voltage %ld\n", + __func__, volt); + return -ENODATA; + } + + /* errminlimit is opp dependent and hence linked to voltage */ + sr->err_minlimit = nvalue_row->errminlimit; + + pm_runtime_get_sync(&sr->pdev->dev); + + /* Check if SR is already enabled. If yes do nothing */ + if (sr_read_reg(sr, SRCONFIG) & SRCONFIG_SRENABLE) + return 0; + + /* Configure SR */ + ret = sr_class->configure(sr); + if (ret) + return ret; + + sr_write_reg(sr, NVALUERECIPROCAL, nvalue_row->nvalue); + + /* SRCONFIG - enable SR */ + sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, SRCONFIG_SRENABLE); + return 0; +} + +/** + * sr_disable() - Disables the smartreflex module. + * @voltdm: VDD pointer to which the SR module to be configured belongs to. + * + * This API is to be called from the smartreflex class driver to + * disable a smartreflex module. + */ +void sr_disable(struct voltagedomain *voltdm) +{ + struct omap_sr *sr = _sr_lookup(voltdm); + + if (IS_ERR(sr)) { + pr_warning("%s: omap_sr struct for voltdm not found\n", __func__); + return; + } + + /* Check if SR clocks are already disabled. If yes do nothing */ + if (pm_runtime_suspended(&sr->pdev->dev)) + return; + + /* + * Disable SR if only it is indeed enabled. Else just + * disable the clocks. + */ + if (sr_read_reg(sr, SRCONFIG) & SRCONFIG_SRENABLE) { + switch (sr->ip_type) { + case SR_TYPE_V1: + sr_v1_disable(sr); + break; + case SR_TYPE_V2: + sr_v2_disable(sr); + break; + default: + dev_err(&sr->pdev->dev, "UNKNOWN IP type %d\n", + sr->ip_type); + } + } + + pm_runtime_put_sync_suspend(&sr->pdev->dev); +} + +/** + * sr_register_class() - API to register a smartreflex class parameters. + * @class_data: The structure containing various sr class specific data. + * + * This API is to be called by the smartreflex class driver to register itself + * with the smartreflex driver during init. Returns 0 on success else the + * error value. + */ +int sr_register_class(struct omap_sr_class_data *class_data) +{ + struct omap_sr *sr_info; + + if (!class_data) { + pr_warning("%s:, Smartreflex class data passed is NULL\n", + __func__); + return -EINVAL; + } + + if (sr_class) { + pr_warning("%s: Smartreflex class driver already registered\n", + __func__); + return -EBUSY; + } + + sr_class = class_data; + + /* + * Call into late init to do intializations that require + * both sr driver and sr class driver to be initiallized. + */ + list_for_each_entry(sr_info, &sr_list, node) + sr_late_init(sr_info); + + return 0; +} + +/** + * omap_sr_enable() - API to enable SR clocks and to call into the + * registered smartreflex class enable API. + * @voltdm: VDD pointer to which the SR module to be configured belongs to. + * + * This API is to be called from the kernel in order to enable + * a particular smartreflex module. This API will do the initial + * configurations to turn on the smartreflex module and in turn call + * into the registered smartreflex class enable API. + */ +void omap_sr_enable(struct voltagedomain *voltdm) +{ + struct omap_sr *sr = _sr_lookup(voltdm); + + if (IS_ERR(sr)) { + pr_warning("%s: omap_sr struct for voltdm not found\n", __func__); + return; + } + + if (!sr->autocomp_active) + return; + + if (!sr_class || !(sr_class->enable) || !(sr_class->configure)) { + dev_warn(&sr->pdev->dev, "%s: smartreflex class driver not" + "registered\n", __func__); + return; + } + + sr_class->enable(sr); +} + +/** + * omap_sr_disable() - API to disable SR without resetting the voltage + * processor voltage + * @voltdm: VDD pointer to which the SR module to be configured belongs to. + * + * This API is to be called from the kernel in order to disable + * a particular smartreflex module. This API will in turn call + * into the registered smartreflex class disable API. This API will tell + * the smartreflex class disable not to reset the VP voltage after + * disabling smartreflex. + */ +void omap_sr_disable(struct voltagedomain *voltdm) +{ + struct omap_sr *sr = _sr_lookup(voltdm); + + if (IS_ERR(sr)) { + pr_warning("%s: omap_sr struct for voltdm not found\n", __func__); + return; + } + + if (!sr->autocomp_active) + return; + + if (!sr_class || !(sr_class->disable)) { + dev_warn(&sr->pdev->dev, "%s: smartreflex class driver not" + "registered\n", __func__); + return; + } + + sr_class->disable(sr, 0); +} + +/** + * omap_sr_disable_reset_volt() - API to disable SR and reset the + * voltage processor voltage + * @voltdm: VDD pointer to which the SR module to be configured belongs to. + * + * This API is to be called from the kernel in order to disable + * a particular smartreflex module. This API will in turn call + * into the registered smartreflex class disable API. This API will tell + * the smartreflex class disable to reset the VP voltage after + * disabling smartreflex. + */ +void omap_sr_disable_reset_volt(struct voltagedomain *voltdm) +{ + struct omap_sr *sr = _sr_lookup(voltdm); + + if (IS_ERR(sr)) { + pr_warning("%s: omap_sr struct for voltdm not found\n", __func__); + return; + } + + if (!sr->autocomp_active) + return; + + if (!sr_class || !(sr_class->disable)) { + dev_warn(&sr->pdev->dev, "%s: smartreflex class driver not" + "registered\n", __func__); + return; + } + + sr_class->disable(sr, 1); +} + +/** + * omap_sr_register_pmic() - API to register pmic specific info. + * @pmic_data: The structure containing pmic specific data. + * + * This API is to be called from the PMIC specific code to register with + * smartreflex driver pmic specific info. Currently the only info required + * is the smartreflex init on the PMIC side. + */ +void omap_sr_register_pmic(struct omap_sr_pmic_data *pmic_data) +{ + if (!pmic_data) { + pr_warning("%s: Trying to register NULL PMIC data structure" + "with smartreflex\n", __func__); + return; + } + + sr_pmic_data = pmic_data; +} + +/* PM Debug FS entries to enable and disable smartreflex. */ +static int omap_sr_autocomp_show(void *data, u64 *val) +{ + struct omap_sr *sr_info = data; + + if (!sr_info) { + pr_warning("%s: omap_sr struct not found\n", __func__); + return -EINVAL; + } + + *val = sr_info->autocomp_active; + + return 0; +} + +static int omap_sr_autocomp_store(void *data, u64 val) +{ + struct omap_sr *sr_info = data; + + if (!sr_info) { + pr_warning("%s: omap_sr struct not found\n", __func__); + return -EINVAL; + } + + /* Sanity check */ + if (val > 1) { + pr_warning("%s: Invalid argument %lld\n", __func__, val); + return -EINVAL; + } + + /* control enable/disable only if there is a delta in value */ + if (sr_info->autocomp_active != val) { + if (!val) + sr_stop_vddautocomp(sr_info); + else + sr_start_vddautocomp(sr_info); + } + + return 0; +} + +DEFINE_SIMPLE_ATTRIBUTE(pm_sr_fops, omap_sr_autocomp_show, + omap_sr_autocomp_store, "%llu\n"); + +static int __init omap_sr_probe(struct platform_device *pdev) +{ + struct omap_sr *sr_info; + struct omap_sr_data *pdata = pdev->dev.platform_data; + struct resource *mem, *irq; + struct dentry *nvalue_dir; + int i, ret = 0; + + sr_info = kzalloc(sizeof(struct omap_sr), GFP_KERNEL); + if (!sr_info) { + dev_err(&pdev->dev, "%s: unable to allocate sr_info\n", + __func__); + return -ENOMEM; + } + + platform_set_drvdata(pdev, sr_info); + + if (!pdata) { + dev_err(&pdev->dev, "%s: platform data missing\n", __func__); + ret = -EINVAL; + goto err_free_devinfo; + } + + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!mem) { + dev_err(&pdev->dev, "%s: no mem resource\n", __func__); + ret = -ENODEV; + goto err_free_devinfo; + } + + mem = request_mem_region(mem->start, resource_size(mem), + dev_name(&pdev->dev)); + if (!mem) { + dev_err(&pdev->dev, "%s: no mem region\n", __func__); + ret = -EBUSY; + goto err_free_devinfo; + } + + irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + + pm_runtime_enable(&pdev->dev); + pm_runtime_irq_safe(&pdev->dev); + + sr_info->name = kasprintf(GFP_KERNEL, "%s", pdata->name); + if (!sr_info->name) { + dev_err(&pdev->dev, "%s: Unable to alloc SR instance name\n", + __func__); + ret = -ENOMEM; + goto err_release_region; + } + + sr_info->pdev = pdev; + sr_info->srid = pdev->id; + sr_info->voltdm = pdata->voltdm; + sr_info->nvalue_table = pdata->nvalue_table; + sr_info->nvalue_count = pdata->nvalue_count; + sr_info->senn_mod = pdata->senn_mod; + sr_info->senp_mod = pdata->senp_mod; + sr_info->autocomp_active = false; + sr_info->ip_type = pdata->ip_type; + sr_info->base = ioremap(mem->start, resource_size(mem)); + if (!sr_info->base) { + dev_err(&pdev->dev, "%s: ioremap fail\n", __func__); + ret = -ENOMEM; + goto err_release_region; + } + + if (irq) + sr_info->irq = irq->start; + + sr_set_clk_length(sr_info); + sr_set_regfields(sr_info); + + list_add(&sr_info->node, &sr_list); + + /* + * Call into late init to do intializations that require + * both sr driver and sr class driver to be initiallized. + */ + if (sr_class) { + ret = sr_late_init(sr_info); + if (ret) { + pr_warning("%s: Error in SR late init\n", __func__); + goto err_iounmap; + } + } + + dev_info(&pdev->dev, "%s: SmartReflex driver initialized\n", __func__); + if (!sr_dbg_dir) { + sr_dbg_dir = debugfs_create_dir("smartreflex", NULL); + if (IS_ERR_OR_NULL(sr_dbg_dir)) { + ret = PTR_ERR(sr_dbg_dir); + pr_err("%s:sr debugfs dir creation failed(%d)\n", + __func__, ret); + goto err_iounmap; + } + } + + sr_info->dbg_dir = debugfs_create_dir(sr_info->name, sr_dbg_dir); + if (IS_ERR_OR_NULL(sr_info->dbg_dir)) { + dev_err(&pdev->dev, "%s: Unable to create debugfs directory\n", + __func__); + ret = PTR_ERR(sr_info->dbg_dir); + goto err_free_name; + } + + (void) debugfs_create_file("autocomp", S_IRUGO | S_IWUSR, + sr_info->dbg_dir, (void *)sr_info, &pm_sr_fops); + (void) debugfs_create_x32("errweight", S_IRUGO, sr_info->dbg_dir, + &sr_info->err_weight); + (void) debugfs_create_x32("errmaxlimit", S_IRUGO, sr_info->dbg_dir, + &sr_info->err_maxlimit); + + nvalue_dir = debugfs_create_dir("nvalue", sr_info->dbg_dir); + if (IS_ERR_OR_NULL(nvalue_dir)) { + dev_err(&pdev->dev, "%s: Unable to create debugfs directory" + "for n-values\n", __func__); + ret = PTR_ERR(nvalue_dir); + goto err_debugfs; + } + + if (sr_info->nvalue_count == 0 || !sr_info->nvalue_table) { + dev_warn(&pdev->dev, "%s: %s: No Voltage table for the corresponding vdd. Cannot create debugfs entries for n-values\n", + __func__, sr_info->name); + + ret = -ENODATA; + goto err_debugfs; + } + + for (i = 0; i < sr_info->nvalue_count; i++) { + char name[NVALUE_NAME_LEN + 1]; + + snprintf(name, sizeof(name), "volt_%lu", + sr_info->nvalue_table[i].volt_nominal); + (void) debugfs_create_x32(name, S_IRUGO | S_IWUSR, nvalue_dir, + &(sr_info->nvalue_table[i].nvalue)); + snprintf(name, sizeof(name), "errminlimit_%lu", + sr_info->nvalue_table[i].volt_nominal); + (void) debugfs_create_x32(name, S_IRUGO | S_IWUSR, nvalue_dir, + &(sr_info->nvalue_table[i].errminlimit)); + + } + + return ret; + +err_debugfs: + debugfs_remove_recursive(sr_info->dbg_dir); +err_free_name: + kfree(sr_info->name); +err_iounmap: + list_del(&sr_info->node); + iounmap(sr_info->base); +err_release_region: + release_mem_region(mem->start, resource_size(mem)); +err_free_devinfo: + kfree(sr_info); + + return ret; +} + +static int __devexit omap_sr_remove(struct platform_device *pdev) +{ + struct omap_sr_data *pdata = pdev->dev.platform_data; + struct omap_sr *sr_info; + struct resource *mem; + + if (!pdata) { + dev_err(&pdev->dev, "%s: platform data missing\n", __func__); + return -EINVAL; + } + + sr_info = _sr_lookup(pdata->voltdm); + if (IS_ERR(sr_info)) { + dev_warn(&pdev->dev, "%s: omap_sr struct not found\n", + __func__); + return PTR_ERR(sr_info); + } + + if (sr_info->autocomp_active) + sr_stop_vddautocomp(sr_info); + if (sr_info->dbg_dir) + debugfs_remove_recursive(sr_info->dbg_dir); + + list_del(&sr_info->node); + iounmap(sr_info->base); + kfree(sr_info->name); + kfree(sr_info); + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + release_mem_region(mem->start, resource_size(mem)); + + return 0; +} + +static void __devexit omap_sr_shutdown(struct platform_device *pdev) +{ + struct omap_sr_data *pdata = pdev->dev.platform_data; + struct omap_sr *sr_info; + + if (!pdata) { + dev_err(&pdev->dev, "%s: platform data missing\n", __func__); + return; + } + + sr_info = _sr_lookup(pdata->voltdm); + if (IS_ERR(sr_info)) { + dev_warn(&pdev->dev, "%s: omap_sr struct not found\n", + __func__); + return; + } + + if (sr_info->autocomp_active) + sr_stop_vddautocomp(sr_info); + + return; +} + +static struct platform_driver smartreflex_driver = { + .remove = __devexit_p(omap_sr_remove), + .shutdown = __devexit_p(omap_sr_shutdown), + .driver = { + .name = "smartreflex", + }, +}; + +static int __init sr_init(void) +{ + int ret = 0; + + /* + * sr_init is a late init. If by then a pmic specific API is not + * registered either there is no need for anything to be done on + * the PMIC side or somebody has forgotten to register a PMIC + * handler. Warn for the second condition. + */ + if (sr_pmic_data && sr_pmic_data->sr_pmic_init) + sr_pmic_data->sr_pmic_init(); + else + pr_warning("%s: No PMIC hook to init smartreflex\n", __func__); + + ret = platform_driver_probe(&smartreflex_driver, omap_sr_probe); + if (ret) { + pr_err("%s: platform driver register failed for SR\n", + __func__); + return ret; + } + + return 0; +} +late_initcall(sr_init); + +static void __exit sr_exit(void) +{ + platform_driver_unregister(&smartreflex_driver); +} +module_exit(sr_exit); + +MODULE_DESCRIPTION("OMAP Smartreflex Driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:" DRIVER_NAME); +MODULE_AUTHOR("Texas Instruments Inc"); |