diff options
Diffstat (limited to 'drivers')
36 files changed, 804 insertions, 258 deletions
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig index f2df6e2a224..676f08b004b 100644 --- a/drivers/ata/Kconfig +++ b/drivers/ata/Kconfig @@ -3,7 +3,7 @@ # menuconfig ATA - tristate "Serial ATA (prod) and Parallel ATA (experimental) drivers" + tristate "Serial ATA and Parallel ATA drivers" depends on HAS_IOMEM depends on BLOCK depends on !(M32R || M68K) || BROKEN @@ -374,8 +374,8 @@ config PATA_HPT366 If unsure, say N. config PATA_HPT37X - tristate "HPT 370/370A/371/372/374/302 PATA support (Experimental)" - depends on PCI && EXPERIMENTAL + tristate "HPT 370/370A/371/372/374/302 PATA support" + depends on PCI help This option enables support for the majority of the later HPT PATA controllers via the new ATA layer. @@ -383,8 +383,8 @@ config PATA_HPT37X If unsure, say N. config PATA_HPT3X2N - tristate "HPT 372N/302N PATA support (Experimental)" - depends on PCI && EXPERIMENTAL + tristate "HPT 372N/302N PATA support" + depends on PCI help This option enables support for the N variant HPT PATA controllers via the new ATA layer @@ -401,7 +401,7 @@ config PATA_HPT3X3 If unsure, say N. config PATA_HPT3X3_DMA - bool "HPT 343/363 DMA support (Experimental)" + bool "HPT 343/363 DMA support" depends on PATA_HPT3X3 help This option enables DMA support for the HPT343/363 @@ -510,8 +510,8 @@ config PATA_NETCELL If unsure, say N. config PATA_NINJA32 - tristate "Ninja32/Delkin Cardbus ATA support (Experimental)" - depends on PCI && EXPERIMENTAL + tristate "Ninja32/Delkin Cardbus ATA support" + depends on PCI help This option enables support for the Ninja32, Delkin and possibly other brands of Cardbus ATA adapter @@ -573,6 +573,14 @@ config PATA_PCMCIA If unsure, say N. +config PATA_PDC2027X + tristate "Promise PATA 2027x support" + depends on PCI + help + This option enables support for Promise PATA pdc20268 to pdc20277 host adapters. + + If unsure, say N. + config PATA_PDC_OLD tristate "Older Promise PATA controller support" depends on PCI @@ -643,14 +651,6 @@ config PATA_SERVERWORKS If unsure, say N. -config PATA_PDC2027X - tristate "Promise PATA 2027x support" - depends on PCI - help - This option enables support for Promise PATA pdc20268 to pdc20277 host adapters. - - If unsure, say N. - config PATA_SIL680 tristate "CMD / Silicon Image 680 PATA support" depends on PCI @@ -667,6 +667,15 @@ config PATA_SIS If unsure, say N. +config PATA_TOSHIBA + tristate "Toshiba Piccolo support (Experimental)" + depends on PCI && EXPERIMENTAL + help + Support for the Toshiba Piccolo controllers. Currently only the + primary channel is supported by this driver. + + If unsure, say N. + config PATA_VIA tristate "VIA PATA support" depends on PCI diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile index 01e126f343b..d909435e9d8 100644 --- a/drivers/ata/Makefile +++ b/drivers/ata/Makefile @@ -63,6 +63,7 @@ obj-$(CONFIG_PATA_RZ1000) += pata_rz1000.o obj-$(CONFIG_PATA_SC1200) += pata_sc1200.o obj-$(CONFIG_PATA_SERVERWORKS) += pata_serverworks.o obj-$(CONFIG_PATA_SIL680) += pata_sil680.o +obj-$(CONFIG_PATA_TOSHIBA) += pata_piccolo.o obj-$(CONFIG_PATA_VIA) += pata_via.o obj-$(CONFIG_PATA_WINBOND) += pata_sl82c105.o obj-$(CONFIG_PATA_WINBOND_VLB) += pata_winbond.o diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index a3241a1a710..b8bea100a16 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -113,6 +113,7 @@ enum { board_ahci_mcp65 = 6, board_ahci_nopmp = 7, board_ahci_yesncq = 8, + board_ahci_nosntf = 9, /* global controller registers */ HOST_CAP = 0x00, /* host capabilities */ @@ -235,6 +236,7 @@ enum { AHCI_HFLAG_NO_SUSPEND = (1 << 10), /* don't suspend */ AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = (1 << 11), /* treat SRST timeout as link offline */ + AHCI_HFLAG_NO_SNTF = (1 << 12), /* no sntf */ /* ap->flags bits */ @@ -508,7 +510,7 @@ static const struct ata_port_info ahci_port_info[] = { .udma_mask = ATA_UDMA6, .port_ops = &ahci_ops, }, - /* board_ahci_yesncq */ + [board_ahci_yesncq] = { AHCI_HFLAGS (AHCI_HFLAG_YES_NCQ), .flags = AHCI_FLAG_COMMON, @@ -516,6 +518,14 @@ static const struct ata_port_info ahci_port_info[] = { .udma_mask = ATA_UDMA6, .port_ops = &ahci_ops, }, + [board_ahci_nosntf] = + { + AHCI_HFLAGS (AHCI_HFLAG_NO_SNTF), + .flags = AHCI_FLAG_COMMON, + .pio_mask = ATA_PIO4, + .udma_mask = ATA_UDMA6, + .port_ops = &ahci_ops, + }, }; static const struct pci_device_id ahci_pci_tbl[] = { @@ -531,7 +541,7 @@ static const struct pci_device_id ahci_pci_tbl[] = { { PCI_VDEVICE(INTEL, 0x2683), board_ahci }, /* ESB2 */ { PCI_VDEVICE(INTEL, 0x27c6), board_ahci }, /* ICH7-M DH */ { PCI_VDEVICE(INTEL, 0x2821), board_ahci }, /* ICH8 */ - { PCI_VDEVICE(INTEL, 0x2822), board_ahci }, /* ICH8 */ + { PCI_VDEVICE(INTEL, 0x2822), board_ahci_nosntf }, /* ICH8 */ { PCI_VDEVICE(INTEL, 0x2824), board_ahci }, /* ICH8 */ { PCI_VDEVICE(INTEL, 0x2829), board_ahci }, /* ICH8M */ { PCI_VDEVICE(INTEL, 0x282a), board_ahci }, /* ICH8M */ @@ -849,6 +859,12 @@ static void ahci_save_initial_config(struct pci_dev *pdev, cap &= ~HOST_CAP_PMP; } + if ((cap & HOST_CAP_SNTF) && (hpriv->flags & AHCI_HFLAG_NO_SNTF)) { + dev_printk(KERN_INFO, &pdev->dev, + "controller can't do SNTF, turning off CAP_SNTF\n"); + cap &= ~HOST_CAP_SNTF; + } + if (pdev->vendor == PCI_VENDOR_ID_JMICRON && pdev->device == 0x2361 && port_map != 1) { dev_printk(KERN_INFO, &pdev->dev, @@ -2988,6 +3004,14 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) if (pdev->vendor == PCI_VENDOR_ID_MARVELL && !marvell_enable) return -ENODEV; + /* Promise's PDC42819 is a SAS/SATA controller that has an AHCI mode. + * At the moment, we can only use the AHCI mode. Let the users know + * that for SAS drives they're out of luck. + */ + if (pdev->vendor == PCI_VENDOR_ID_PROMISE) + dev_printk(KERN_INFO, &pdev->dev, "PDC42819 " + "can only drive SATA devices with this driver\n"); + /* acquire resources */ rc = pcim_enable_device(pdev); if (rc) diff --git a/drivers/ata/ata_generic.c b/drivers/ata/ata_generic.c index ecfd22b4f1c..12e26c3c68e 100644 --- a/drivers/ata/ata_generic.c +++ b/drivers/ata/ata_generic.c @@ -168,9 +168,12 @@ static struct pci_device_id ata_generic[] = { { PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C561), }, { PCI_DEVICE(PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C558), }, { PCI_DEVICE(PCI_VENDOR_ID_CENATEK,PCI_DEVICE_ID_CENATEK_IDE), }, - { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO), }, +#if !defined(CONFIG_PATA_TOSHIBA) && !defined(CONFIG_PATA_TOSHIBA_MODULE) { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_1), }, { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_2), }, + { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_3), }, + { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_5), }, +#endif /* Must come last. If you add entries adjust this table appropriately */ { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xFFFFFF00UL, 1}, { 0, }, diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c index 9ac4e378992..0c6155f5117 100644 --- a/drivers/ata/ata_piix.c +++ b/drivers/ata/ata_piix.c @@ -869,10 +869,10 @@ static void do_pata_set_dmamode(struct ata_port *ap, struct ata_device *adev, in (timings[pio][1] << 8); } - if (ap->udma_mask) { + if (ap->udma_mask) udma_enable &= ~(1 << devid); - pci_write_config_word(dev, master_port, master_data); - } + + pci_write_config_word(dev, master_port, master_data); } /* Don't scribble on 0x48 if the controller does not support UDMA */ if (ap->udma_mask) diff --git a/drivers/ata/libata-acpi.c b/drivers/ata/libata-acpi.c index b0882cddfd4..1245838ac13 100644 --- a/drivers/ata/libata-acpi.c +++ b/drivers/ata/libata-acpi.c @@ -807,12 +807,11 @@ static int ata_acpi_exec_tfs(struct ata_device *dev, int *nr_executed) * EH context. * * RETURNS: - * 0 on success, -errno on failure. + * 0 on success, -ENOENT if _SDD doesn't exist, -errno on failure. */ static int ata_acpi_push_id(struct ata_device *dev) { struct ata_port *ap = dev->link->ap; - int err; acpi_status status; struct acpi_object_list input; union acpi_object in_params[1]; @@ -835,12 +834,16 @@ static int ata_acpi_push_id(struct ata_device *dev) status = acpi_evaluate_object(dev->acpi_handle, "_SDD", &input, NULL); swap_buf_le16(dev->id, ATA_ID_WORDS); - err = ACPI_FAILURE(status) ? -EIO : 0; - if (err < 0) + if (status == AE_NOT_FOUND) + return -ENOENT; + + if (ACPI_FAILURE(status)) { ata_dev_printk(dev, KERN_WARNING, "ACPI _SDD failed (AE 0x%x)\n", status); + return -EIO; + } - return err; + return 0; } /** @@ -971,7 +974,7 @@ int ata_acpi_on_devcfg(struct ata_device *dev) /* do _SDD if SATA */ if (acpi_sata) { rc = ata_acpi_push_id(dev); - if (rc) + if (rc && rc != -ENOENT) goto acpi_err; } diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index dc72690ed5d..22ff51bdbc8 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -6616,6 +6616,13 @@ static int __init ata_init(void) { ata_parse_force_param(); + /* + * FIXME: In UP case, there is only one workqueue thread and if you + * have more than one PIO device, latency is bloody awful, with + * occasional multi-second "hiccups" as one PIO device waits for + * another. It's an ugly wart that users DO occasionally complain + * about; luckily most users have at most one PIO polled device. + */ ata_wq = create_workqueue("ata"); if (!ata_wq) goto free_force_tbl; diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c index bba2ae5df1c..0ea97c942ce 100644 --- a/drivers/ata/libata-eh.c +++ b/drivers/ata/libata-eh.c @@ -110,6 +110,13 @@ static const unsigned long ata_eh_identify_timeouts[] = { ULONG_MAX, }; +static const unsigned long ata_eh_flush_timeouts[] = { + 15000, /* be generous with flush */ + 15000, /* ditto */ + 30000, /* and even more generous */ + ULONG_MAX, +}; + static const unsigned long ata_eh_other_timeouts[] = { 5000, /* same rationale as identify timeout */ 10000, /* ditto */ @@ -147,6 +154,8 @@ ata_eh_cmd_timeout_table[ATA_EH_CMD_TIMEOUT_TABLE_SIZE] = { .timeouts = ata_eh_other_timeouts, }, { .commands = CMDS(ATA_CMD_INIT_DEV_PARAMS), .timeouts = ata_eh_other_timeouts, }, + { .commands = CMDS(ATA_CMD_FLUSH, ATA_CMD_FLUSH_EXT), + .timeouts = ata_eh_flush_timeouts }, }; #undef CMDS @@ -3112,6 +3121,82 @@ static int atapi_eh_clear_ua(struct ata_device *dev) return 0; } +/** + * ata_eh_maybe_retry_flush - Retry FLUSH if necessary + * @dev: ATA device which may need FLUSH retry + * + * If @dev failed FLUSH, it needs to be reported upper layer + * immediately as it means that @dev failed to remap and already + * lost at least a sector and further FLUSH retrials won't make + * any difference to the lost sector. However, if FLUSH failed + * for other reasons, for example transmission error, FLUSH needs + * to be retried. + * + * This function determines whether FLUSH failure retry is + * necessary and performs it if so. + * + * RETURNS: + * 0 if EH can continue, -errno if EH needs to be repeated. + */ +static int ata_eh_maybe_retry_flush(struct ata_device *dev) +{ + struct ata_link *link = dev->link; + struct ata_port *ap = link->ap; + struct ata_queued_cmd *qc; + struct ata_taskfile tf; + unsigned int err_mask; + int rc = 0; + + /* did flush fail for this device? */ + if (!ata_tag_valid(link->active_tag)) + return 0; + + qc = __ata_qc_from_tag(ap, link->active_tag); + if (qc->dev != dev || (qc->tf.command != ATA_CMD_FLUSH_EXT && + qc->tf.command != ATA_CMD_FLUSH)) + return 0; + + /* if the device failed it, it should be reported to upper layers */ + if (qc->err_mask & AC_ERR_DEV) + return 0; + + /* flush failed for some other reason, give it another shot */ + ata_tf_init(dev, &tf); + + tf.command = qc->tf.command; + tf.flags |= ATA_TFLAG_DEVICE; + tf.protocol = ATA_PROT_NODATA; + + ata_dev_printk(dev, KERN_WARNING, "retrying FLUSH 0x%x Emask 0x%x\n", + tf.command, qc->err_mask); + + err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0); + if (!err_mask) { + /* + * FLUSH is complete but there's no way to + * successfully complete a failed command from EH. + * Making sure retry is allowed at least once and + * retrying it should do the trick - whatever was in + * the cache is already on the platter and this won't + * cause infinite loop. + */ + qc->scsicmd->allowed = max(qc->scsicmd->allowed, 1); + } else { + ata_dev_printk(dev, KERN_WARNING, "FLUSH failed Emask 0x%x\n", + err_mask); + rc = -EIO; + + /* if device failed it, report it to upper layers */ + if (err_mask & AC_ERR_DEV) { + qc->err_mask |= AC_ERR_DEV; + qc->result_tf = tf; + if (!(ap->pflags & ATA_PFLAG_FROZEN)) + rc = 0; + } + } + return rc; +} + static int ata_link_nr_enabled(struct ata_link *link) { struct ata_device *dev; @@ -3455,6 +3540,15 @@ int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset, } } + /* retry flush if necessary */ + ata_for_each_dev(dev, link, ALL) { + if (dev->class != ATA_DEV_ATA) + continue; + rc = ata_eh_maybe_retry_flush(dev); + if (rc) + goto dev_fail; + } + /* configure link power saving */ if (ehc->i.action & ATA_EH_LPM) ata_for_each_dev(dev, link, ALL) diff --git a/drivers/ata/libata-scsi.c b/drivers/ata/libata-scsi.c index b4ee28dec52..62e6b9ea96a 100644 --- a/drivers/ata/libata-scsi.c +++ b/drivers/ata/libata-scsi.c @@ -47,6 +47,7 @@ #include <linux/hdreg.h> #include <linux/uaccess.h> #include <linux/suspend.h> +#include <asm/unaligned.h> #include "libata.h" @@ -154,8 +155,7 @@ static ssize_t ata_scsi_lpm_put(struct device *dev, */ for (i = 1; i < ARRAY_SIZE(link_pm_policy); i++) { const int len = strlen(link_pm_policy[i].name); - if (strncmp(link_pm_policy[i].name, buf, len) == 0 && - buf[len] == '\n') { + if (strncmp(link_pm_policy[i].name, buf, len) == 0) { policy = link_pm_policy[i].value; break; } @@ -1964,6 +1964,7 @@ static unsigned int ata_scsiop_inq_00(struct ata_scsi_args *args, u8 *rbuf) 0x80, /* page 0x80, unit serial no page */ 0x83, /* page 0x83, device ident page */ 0x89, /* page 0x89, ata info page */ + 0xb0, /* page 0xb0, block limits page */ 0xb1, /* page 0xb1, block device characteristics page */ }; @@ -2085,6 +2086,43 @@ static unsigned int ata_scsiop_inq_89(struct ata_scsi_args *args, u8 *rbuf) return 0; } +static unsigned int ata_scsiop_inq_b0(struct ata_scsi_args *args, u8 *rbuf) +{ + u32 min_io_sectors; + + rbuf[1] = 0xb0; + rbuf[3] = 0x3c; /* required VPD size with unmap support */ + + /* + * Optimal transfer length granularity. + * + * This is always one physical block, but for disks with a smaller + * logical than physical sector size we need to figure out what the + * latter is. + */ + if (ata_id_has_large_logical_sectors(args->id)) + min_io_sectors = ata_id_logical_per_physical_sectors(args->id); + else + min_io_sectors = 1; + put_unaligned_be16(min_io_sectors, &rbuf[6]); + + /* + * Optimal unmap granularity. + * + * The ATA spec doesn't even know about a granularity or alignment + * for the TRIM command. We can leave away most of the unmap related + * VPD page entries, but we have specifify a granularity to signal + * that we support some form of unmap - in thise case via WRITE SAME + * with the unmap bit set. + */ + if (ata_id_has_trim(args->id)) { + put_unaligned_be32(65535 * 512 / 8, &rbuf[20]); + put_unaligned_be32(1, &rbuf[28]); + } + + return 0; +} + static unsigned int ata_scsiop_inq_b1(struct ata_scsi_args *args, u8 *rbuf) { int form_factor = ata_id_form_factor(args->id); @@ -2374,6 +2412,13 @@ static unsigned int ata_scsiop_read_cap(struct ata_scsi_args *args, u8 *rbuf) rbuf[13] = log_per_phys; rbuf[14] = (lowest_aligned >> 8) & 0x3f; rbuf[15] = lowest_aligned; + + if (ata_id_has_trim(args->id)) { + rbuf[14] |= 0x80; /* TPE */ + + if (ata_id_has_zero_after_trim(args->id)) + rbuf[14] |= 0x40; /* TPRZ */ + } } return 0; @@ -2896,6 +2941,58 @@ static unsigned int ata_scsi_pass_thru(struct ata_queued_cmd *qc) return 1; } +static unsigned int ata_scsi_write_same_xlat(struct ata_queued_cmd *qc) +{ + struct ata_taskfile *tf = &qc->tf; + struct scsi_cmnd *scmd = qc->scsicmd; + struct ata_device *dev = qc->dev; + const u8 *cdb = scmd->cmnd; + u64 block; + u32 n_block; + u32 size; + void *buf; + + /* we may not issue DMA commands if no DMA mode is set */ + if (unlikely(!dev->dma_mode)) + goto invalid_fld; + + if (unlikely(scmd->cmd_len < 16)) + goto invalid_fld; + scsi_16_lba_len(cdb, &block, &n_block); + + /* for now we only support WRITE SAME with the unmap bit set */ + if (unlikely(!(cdb[1] & 0x8))) + goto invalid_fld; + + /* + * WRITE SAME always has a sector sized buffer as payload, this + * should never be a multiple entry S/G list. + */ + if (!scsi_sg_count(scmd)) + goto invalid_fld; + + buf = page_address(sg_page(scsi_sglist(scmd))); + size = ata_set_lba_range_entries(buf, 512, block, n_block); + + tf->protocol = ATA_PROT_DMA; + tf->hob_feature = 0; + tf->feature = ATA_DSM_TRIM; + tf->hob_nsect = (size / 512) >> 8; + tf->nsect = size / 512; + tf->command = ATA_CMD_DSM; + tf->flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE | ATA_TFLAG_LBA48 | + ATA_TFLAG_WRITE; + + ata_qc_set_pc_nbytes(qc); + + return 0; + + invalid_fld: + ata_scsi_set_sense(scmd, ILLEGAL_REQUEST, 0x24, 0x00); + /* "Invalid field in cdb" */ + return 1; +} + /** * ata_get_xlat_func - check if SCSI to ATA translation is possible * @dev: ATA device @@ -2920,6 +3017,9 @@ static inline ata_xlat_func_t ata_get_xlat_func(struct ata_device *dev, u8 cmd) case WRITE_16: return ata_scsi_rw_xlat; + case 0x93 /*WRITE_SAME_16*/: + return ata_scsi_write_same_xlat; + case SYNCHRONIZE_CACHE: if (ata_try_flush_cache(dev)) return ata_scsi_flush_xlat; @@ -3109,6 +3209,9 @@ void ata_scsi_simulate(struct ata_device *dev, struct scsi_cmnd *cmd, case 0x89: ata_scsi_rbuf_fill(&args, ata_scsiop_inq_89); break; + case 0xb0: + ata_scsi_rbuf_fill(&args, ata_scsiop_inq_b0); + break; case 0xb1: ata_scsi_rbuf_fill(&args, ata_scsiop_inq_b1); break; diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c index bbbb1fab175..51eb1e29860 100644 --- a/drivers/ata/libata-sff.c +++ b/drivers/ata/libata-sff.c @@ -2384,7 +2384,7 @@ void ata_sff_post_internal_cmd(struct ata_queued_cmd *qc) ap->hsm_task_state = HSM_ST_IDLE; if (ap->ioaddr.bmdma_addr) - ata_bmdma_stop(qc); + ap->ops->bmdma_stop(qc); spin_unlock_irqrestore(ap->lock, flags); } diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c index 1432dc9d0ab..9434114b2ca 100644 --- a/drivers/ata/pata_ali.c +++ b/drivers/ata/pata_ali.c @@ -453,7 +453,9 @@ static void ali_init_chipset(struct pci_dev *pdev) /* Clear CD-ROM DMA write bit */ tmp &= 0x7F; /* Cable and UDMA */ - pci_write_config_byte(pdev, 0x4B, tmp | 0x09); + if (pdev->revision >= 0xc2) + tmp |= 0x01; + pci_write_config_byte(pdev, 0x4B, tmp | 0x08); /* * CD_ROM DMA on (0x53 bit 0). Enable this even if we want * to use PIO. 0x53 bit 1 (rev 20 only) - enable FIFO control diff --git a/drivers/ata/pata_cmd64x.c b/drivers/ata/pata_cmd64x.c index f98dffedf4b..dadfc358ba1 100644 --- a/drivers/ata/pata_cmd64x.c +++ b/drivers/ata/pata_cmd64x.c @@ -31,7 +31,7 @@ #include <linux/libata.h> #define DRV_NAME "pata_cmd64x" -#define DRV_VERSION "0.2.5" +#define DRV_VERSION "0.3.1" /* * CMD64x specific registers definition. @@ -254,17 +254,109 @@ static void cmd648_bmdma_stop(struct ata_queued_cmd *qc) } /** - * cmd646r1_dma_stop - DMA stop callback + * cmd64x_bmdma_stop - DMA stop callback * @qc: Command in progress * - * Stub for now while investigating the r1 quirk in the old driver. + * Track the completion of live DMA commands and clear the + * host->private_data DMA tracking flag as we do. */ -static void cmd646r1_bmdma_stop(struct ata_queued_cmd *qc) +static void cmd64x_bmdma_stop(struct ata_queued_cmd *qc) { + struct ata_port *ap = qc->ap; ata_bmdma_stop(qc); + WARN_ON(ap->host->private_data != ap); + ap->host->private_data = NULL; } +/** + * cmd64x_qc_defer - Defer logic for chip limits + * @qc: queued command + * + * Decide whether we can issue the command. Called under the host lock. + */ + +static int cmd64x_qc_defer(struct ata_queued_cmd *qc) +{ + struct ata_host *host = qc->ap->host; + struct ata_port *alt = host->ports[1 ^ qc->ap->port_no]; + int rc; + int dma = 0; + + /* Apply the ATA rules first */ + rc = ata_std_qc_defer(qc); + if (rc) + return rc; + + if (qc->tf.protocol == ATAPI_PROT_DMA || + qc->tf.protocol == ATA_PROT_DMA) + dma = 1; + + /* If the other port is not live then issue the command */ + if (alt == NULL || !alt->qc_active) { + if (dma) + host->private_data = qc->ap; + return 0; + } + /* If there is a live DMA command then wait */ + if (host->private_data != NULL) + return ATA_DEFER_PORT; + if (dma) + /* Cannot overlap our DMA command */ + return ATA_DEFER_PORT; + return 0; +} + +/** + * cmd64x_interrupt - ATA host interrupt handler + * @irq: irq line (unused) + * @dev_instance: pointer to our ata_host information structure + * + * Our interrupt handler for PCI IDE devices. Calls + * ata_sff_host_intr() for each port that is flagging an IRQ. We cannot + * use the defaults as we need to avoid touching status/altstatus during + * a DMA. + * + * LOCKING: + * Obtains host lock during operation. + * + * RETURNS: + * IRQ_NONE or IRQ_HANDLED. + */ +irqreturn_t cmd64x_interrupt(int irq, void *dev_instance) +{ + struct ata_host *host = dev_instance; + struct pci_dev *pdev = to_pci_dev(host->dev); + unsigned int i; + unsigned int handled = 0; + unsigned long flags; + static const u8 irq_reg[2] = { CFR, ARTTIM23 }; + static const u8 irq_mask[2] = { 1 << 2, 1 << 4 }; + + /* TODO: make _irqsave conditional on x86 PCI IDE legacy mode */ + spin_lock_irqsave(&host->lock, flags); + + for (i = 0; i < host->n_ports; i++) { + struct ata_port *ap; + u8 reg; + + pci_read_config_byte(pdev, irq_reg[i], ®); + ap = host->ports[i]; + if (ap && (reg & irq_mask[i]) && + !(ap->flags & ATA_FLAG_DISABLED)) { + struct ata_queued_cmd *qc; + + qc = ata_qc_from_tag(ap, ap->link.active_tag); + if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING)) && + (qc->flags & ATA_QCFLAG_ACTIVE)) + handled |= ata_sff_host_intr(ap, qc); + } + } + + spin_unlock_irqrestore(&host->lock, flags); + + return IRQ_RETVAL(handled); +} static struct scsi_host_template cmd64x_sht = { ATA_BMDMA_SHT(DRV_NAME), }; @@ -273,6 +365,8 @@ static const struct ata_port_operations cmd64x_base_ops = { .inherits = &ata_bmdma_port_ops, .set_piomode = cmd64x_set_piomode, .set_dmamode = cmd64x_set_dmamode, + .bmdma_stop = cmd64x_bmdma_stop, + .qc_defer = cmd64x_qc_defer, }; static struct ata_port_operations cmd64x_port_ops = { @@ -282,7 +376,6 @@ static struct ata_port_operations cmd64x_port_ops = { static struct ata_port_operations cmd646r1_port_ops = { .inherits = &cmd64x_base_ops, - .bmdma_stop = cmd646r1_bmdma_stop, .cable_detect = ata_cable_40wire, }; @@ -290,12 +383,11 @@ static struct ata_port_operations cmd648_port_ops = { .inherits = &cmd64x_base_ops, .bmdma_stop = cmd648_bmdma_stop, .cable_detect = cmd648_cable_detect, + .qc_defer = ata_std_qc_defer }; static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id) { - u32 class_rev; - static const struct ata_port_info cmd_info[6] = { { /* CMD 643 - no UDMA */ .flags = ATA_FLAG_SLAVE_POSS, @@ -340,40 +432,43 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id) const struct ata_port_info *ppi[] = { &cmd_info[id->driver_data], NULL }; u8 mrdmode; int rc; + struct ata_host *host; rc = pcim_enable_device(pdev); if (rc) return rc; - pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class_rev); - class_rev &= 0xFF; - if (id->driver_data == 0) /* 643 */ ata_pci_bmdma_clear_simplex(pdev); if (pdev->device == PCI_DEVICE_ID_CMD_646) { /* Does UDMA work ? */ - if (class_rev > 4) + if (pdev->revision > 4) ppi[0] = &cmd_info[2]; /* Early rev with other problems ? */ - else if (class_rev == 1) + else if (pdev->revision == 1) ppi[0] = &cmd_info[3]; } + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 64); pci_read_config_byte(pdev, MRDMODE, &mrdmode); mrdmode &= ~ 0x30; /* IRQ set up */ mrdmode |= 0x02; /* Memory read line enable */ pci_write_config_byte(pdev, MRDMODE, mrdmode); - /* Force PIO 0 here.. */ - /* PPC specific fixup copied from old driver */ #ifdef CONFIG_PPC pci_write_config_byte(pdev, UDIDETCR0, 0xF0); #endif + rc = ata_pci_sff_prepare_host(pdev, ppi, &host); + if (rc) + return rc; + /* We use this pointer to track the AP which has DMA running */ + host->private_data = NULL; - return ata_pci_sff_init_one(pdev, ppi, &cmd64x_sht, NULL); + pci_set_master(pdev); + return ata_pci_sff_activate_host(host, cmd64x_interrupt, &cmd64x_sht); } #ifdef CONFIG_PM diff --git a/drivers/ata/pata_cs5520.c b/drivers/ata/pata_cs5520.c index 0df83cf7423..95ebdac517f 100644 --- a/drivers/ata/pata_cs5520.c +++ b/drivers/ata/pata_cs5520.c @@ -90,48 +90,12 @@ static void cs5520_set_timings(struct ata_port *ap, struct ata_device *adev, int } /** - * cs5520_enable_dma - turn on DMA bits - * - * Turn on the DMA bits for this disk. Needed because the BIOS probably - * has not done the work for us. Belongs in the core SATA code. - */ - -static void cs5520_enable_dma(struct ata_port *ap, struct ata_device *adev) -{ - /* Set the DMA enable/disable flag */ - u8 reg = ioread8(ap->ioaddr.bmdma_addr + 0x02); - reg |= 1<<(adev->devno + 5); - iowrite8(reg, ap->ioaddr.bmdma_addr + 0x02); -} - -/** - * cs5520_set_dmamode - program DMA timings - * @ap: ATA port - * @adev: ATA device - * - * Program the DMA mode timings for the controller according to the pio - * clocking table. Note that this device sets the DMA timings to PIO - * mode values. This may seem bizarre but the 5520 architecture talks - * PIO mode to the disk and DMA mode to the controller so the underlying - * transfers are PIO timed. - */ - -static void cs5520_set_dmamode(struct ata_port *ap, struct ata_device *adev) -{ - static const int dma_xlate[3] = { XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 }; - cs5520_set_timings(ap, adev, dma_xlate[adev->dma_mode]); - cs5520_enable_dma(ap, adev); -} - -/** * cs5520_set_piomode - program PIO timings * @ap: ATA port * @adev: ATA device * * Program the PIO mode timings for the controller according to the pio - * clocking table. We know pio_mode will equal dma_mode because of the - * CS5520 architecture. At least once we turned DMA on and wrote a - * mode setter. + * clocking table. */ static void cs5520_set_piomode(struct ata_port *ap, struct ata_device *adev) @@ -149,7 +113,6 @@ static struct ata_port_operations cs5520_port_ops = { .qc_prep = ata_sff_dumb_qc_prep, .cable_detect = ata_cable_40wire, .set_piomode = cs5520_set_piomode, - .set_dmamode = cs5520_set_dmamode, }; static int __devinit cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id) diff --git a/drivers/ata/pata_cs5536.c b/drivers/ata/pata_cs5536.c index 6da4cb486c8..ffee3978ec8 100644 --- a/drivers/ata/pata_cs5536.c +++ b/drivers/ata/pata_cs5536.c @@ -224,7 +224,7 @@ static struct scsi_host_template cs5536_sht = { }; static struct ata_port_operations cs5536_port_ops = { - .inherits = &ata_bmdma_port_ops, + .inherits = &ata_bmdma32_port_ops, .cable_detect = cs5536_cable_detect, .set_piomode = cs5536_set_piomode, .set_dmamode = cs5536_set_dmamode, diff --git a/drivers/ata/pata_efar.c b/drivers/ata/pata_efar.c index 2a6412f5d11..b2e71e6473e 100644 --- a/drivers/ata/pata_efar.c +++ b/drivers/ata/pata_efar.c @@ -2,6 +2,7 @@ * pata_efar.c - EFAR PIIX clone controller driver * * (C) 2005 Red Hat + * (C) 2009 Bartlomiej Zolnierkiewicz * * Some parts based on ata_piix.c by Jeff Garzik and others. * @@ -118,12 +119,12 @@ static void efar_set_piomode (struct ata_port *ap, struct ata_device *adev) int shift = 4 * ap->port_no; u8 slave_data; - idetm_data &= 0xCC0F; + idetm_data &= 0xFF0F; idetm_data |= (control << 4); /* Slave timing in separate register */ pci_read_config_byte(dev, 0x44, &slave_data); - slave_data &= 0x0F << shift; + slave_data &= ap->port_no ? 0x0F : 0xF0; slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << shift; pci_write_config_byte(dev, 0x44, slave_data); } @@ -200,7 +201,7 @@ static void efar_set_dmamode (struct ata_port *ap, struct ata_device *adev) master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */ master_data |= control << 4; pci_read_config_byte(dev, 0x44, &slave_data); - slave_data &= (0x0F + 0xE1 * ap->port_no); + slave_data &= ap->port_no ? 0x0F : 0xF0; /* Load the matching timing */ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0); pci_write_config_byte(dev, 0x44, slave_data); @@ -251,7 +252,7 @@ static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) static const struct ata_port_info info = { .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA2, + .mwdma_mask = ATA_MWDMA12_ONLY, .udma_mask = ATA_UDMA4, .port_ops = &efar_ops, }; diff --git a/drivers/ata/pata_hpt366.c b/drivers/ata/pata_hpt366.c index d7f2da127d1..0bd48e8f21b 100644 --- a/drivers/ata/pata_hpt366.c +++ b/drivers/ata/pata_hpt366.c @@ -27,7 +27,7 @@ #include <linux/libata.h> #define DRV_NAME "pata_hpt366" -#define DRV_VERSION "0.6.2" +#define DRV_VERSION "0.6.7" struct hpt_clock { u8 xfer_mode; @@ -36,24 +36,22 @@ struct hpt_clock { /* key for bus clock timings * bit - * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW - * DMA. cycles = value + 1 - * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW - * DMA. cycles = value + 1 - * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file + * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA. + * cycles = value + 1 + * 4:7 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA. + * cycles = value + 1 + * 8:11 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file * register access. - * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file + * 12:15 cmd_low_time. Active time of DIOW_/DIOR_ during task file * register access. - * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer. - * during task file register access. - * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA - * xfer. - * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task + * 16:18 udma_cycle_time. Clock cycles for UDMA xfer? + * 19:21 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer. + * 22:24 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file * register access. - * 28 UDMA enable - * 29 DMA enable - * 30 PIO_MST enable. if set, the chip is in bus master mode during - * PIO. + * 28 UDMA enable. + * 29 DMA enable. + * 30 PIO_MST enable. If set, the chip is in bus master mode during + * PIO xfer. * 31 FIFO enable. */ @@ -344,7 +342,6 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id) const struct ata_port_info *ppi[] = { &info_hpt366, NULL }; void *hpriv = NULL; - u32 class_rev; u32 reg1; int rc; @@ -352,13 +349,10 @@ static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id) if (rc) return rc; - pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); - class_rev &= 0xFF; - /* May be a later chip in disguise. Check */ /* Newer chips are not in the HPT36x driver. Ignore them */ - if (class_rev > 2) - return -ENODEV; + if (dev->revision > 2) + return -ENODEV; hpt36x_init_chipset(dev); diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c index d0a7df2e5ca..4224cfccede 100644 --- a/drivers/ata/pata_hpt37x.c +++ b/drivers/ata/pata_hpt37x.c @@ -24,7 +24,7 @@ #include <linux/libata.h> #define DRV_NAME "pata_hpt37x" -#define DRV_VERSION "0.6.12" +#define DRV_VERSION "0.6.14" struct hpt_clock { u8 xfer_speed; @@ -303,72 +303,79 @@ static unsigned long hpt370a_filter(struct ata_device *adev, unsigned long mask) } /** - * hpt37x_pre_reset - reset the hpt37x bus - * @link: ATA link to reset - * @deadline: deadline jiffies for the operation + * hpt37x_cable_detect - Detect the cable type + * @ap: ATA port to detect on * - * Perform the initial reset handling for the 370/372 and 374 func 0 + * Return the cable type attached to this port */ -static int hpt37x_pre_reset(struct ata_link *link, unsigned long deadline) +static int hpt37x_cable_detect(struct ata_port *ap) { - u8 scr2, ata66; - struct ata_port *ap = link->ap; struct pci_dev *pdev = to_pci_dev(ap->host->dev); - static const struct pci_bits hpt37x_enable_bits[] = { - { 0x50, 1, 0x04, 0x04 }, - { 0x54, 1, 0x04, 0x04 } - }; - if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no])) - return -ENOENT; + u8 scr2, ata66; pci_read_config_byte(pdev, 0x5B, &scr2); pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01); + + udelay(10); /* debounce */ + /* Cable register now active */ pci_read_config_byte(pdev, 0x5A, &ata66); /* Restore state */ pci_write_config_byte(pdev, 0x5B, scr2); if (ata66 & (2 >> ap->port_no)) - ap->cbl = ATA_CBL_PATA40; + return ATA_CBL_PATA40; else - ap->cbl = ATA_CBL_PATA80; - - /* Reset the state machine */ - pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); - udelay(100); - - return ata_sff_prereset(link, deadline); + return ATA_CBL_PATA80; } -static int hpt374_fn1_pre_reset(struct ata_link *link, unsigned long deadline) +/** + * hpt374_fn1_cable_detect - Detect the cable type + * @ap: ATA port to detect on + * + * Return the cable type attached to this port + */ + +static int hpt374_fn1_cable_detect(struct ata_port *ap) { - static const struct pci_bits hpt37x_enable_bits[] = { - { 0x50, 1, 0x04, 0x04 }, - { 0x54, 1, 0x04, 0x04 } - }; - u16 mcr3; - u8 ata66; - struct ata_port *ap = link->ap; struct pci_dev *pdev = to_pci_dev(ap->host->dev); unsigned int mcrbase = 0x50 + 4 * ap->port_no; - - if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no])) - return -ENOENT; + u16 mcr3; + u8 ata66; /* Do the extra channel work */ pci_read_config_word(pdev, mcrbase + 2, &mcr3); - /* Set bit 15 of 0x52 to enable TCBLID as input - */ + /* Set bit 15 of 0x52 to enable TCBLID as input */ pci_write_config_word(pdev, mcrbase + 2, mcr3 | 0x8000); pci_read_config_byte(pdev, 0x5A, &ata66); /* Reset TCBLID/FCBLID to output */ pci_write_config_word(pdev, mcrbase + 2, mcr3); if (ata66 & (2 >> ap->port_no)) - ap->cbl = ATA_CBL_PATA40; + return ATA_CBL_PATA40; else - ap->cbl = ATA_CBL_PATA80; + return ATA_CBL_PATA80; +} + +/** + * hpt37x_pre_reset - reset the hpt37x bus + * @link: ATA link to reset + * @deadline: deadline jiffies for the operation + * + * Perform the initial reset handling for the HPT37x. + */ + +static int hpt37x_pre_reset(struct ata_link *link, unsigned long deadline) +{ + struct ata_port *ap = link->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + static const struct pci_bits hpt37x_enable_bits[] = { + { 0x50, 1, 0x04, 0x04 }, + { 0x54, 1, 0x04, 0x04 } + }; + if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no])) + return -ENOENT; /* Reset the state machine */ pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); @@ -404,9 +411,8 @@ static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev) pci_read_config_dword(pdev, addr1, ®); mode = hpt37x_find_mode(ap, adev->pio_mode); - mode &= ~0x8000000; /* No FIFO in PIO */ - mode &= ~0x30070000; /* Leave config bits alone */ - reg &= 0x30070000; /* Strip timing bits */ + mode &= 0xCFC3FFFF; /* Leave DMA bits alone */ + reg &= ~0xCFC3FFFF; /* Strip timing bits */ pci_write_config_dword(pdev, addr1, reg | mode); } @@ -423,8 +429,7 @@ static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); u32 addr1, addr2; - u32 reg; - u32 mode; + u32 reg, mode, mask; u8 fast; addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); @@ -436,11 +441,12 @@ static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev) fast |= 0x01; pci_write_config_byte(pdev, addr2, fast); + mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000; + pci_read_config_dword(pdev, addr1, ®); mode = hpt37x_find_mode(ap, adev->dma_mode); - mode |= 0x8000000; /* FIFO in MWDMA or UDMA */ - mode &= ~0xC0000000; /* Leave config bits alone */ - reg &= 0xC0000000; /* Strip timing bits */ + mode &= mask; + reg &= ~mask; pci_write_config_dword(pdev, addr1, reg | mode); } @@ -508,9 +514,8 @@ static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev) mode = hpt37x_find_mode(ap, adev->pio_mode); printk("Find mode for %d reports %X\n", adev->pio_mode, mode); - mode &= ~0x80000000; /* No FIFO in PIO */ - mode &= ~0x30070000; /* Leave config bits alone */ - reg &= 0x30070000; /* Strip timing bits */ + mode &= 0xCFC3FFFF; /* Leave DMA bits alone */ + reg &= ~0xCFC3FFFF; /* Strip timing bits */ pci_write_config_dword(pdev, addr1, reg | mode); } @@ -527,8 +532,7 @@ static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); u32 addr1, addr2; - u32 reg; - u32 mode; + u32 reg, mode, mask; u8 fast; addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); @@ -539,12 +543,13 @@ static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev) fast &= ~0x07; pci_write_config_byte(pdev, addr2, fast); + mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000; + pci_read_config_dword(pdev, addr1, ®); mode = hpt37x_find_mode(ap, adev->dma_mode); printk("Find mode for DMA %d reports %X\n", adev->dma_mode, mode); - mode &= ~0xC0000000; /* Leave config bits alone */ - mode |= 0x80000000; /* FIFO in MWDMA or UDMA */ - reg &= 0xC0000000; /* Strip timing bits */ + mode &= mask; + reg &= ~mask; pci_write_config_dword(pdev, addr1, reg | mode); } @@ -584,6 +589,7 @@ static struct ata_port_operations hpt370_port_ops = { .bmdma_stop = hpt370_bmdma_stop, .mode_filter = hpt370_filter, + .cable_detect = hpt37x_cable_detect, .set_piomode = hpt370_set_piomode, .set_dmamode = hpt370_set_dmamode, .prereset = hpt37x_pre_reset, @@ -608,6 +614,7 @@ static struct ata_port_operations hpt372_port_ops = { .bmdma_stop = hpt37x_bmdma_stop, + .cable_detect = hpt37x_cable_detect, .set_piomode = hpt372_set_piomode, .set_dmamode = hpt372_set_dmamode, .prereset = hpt37x_pre_reset, @@ -620,7 +627,8 @@ static struct ata_port_operations hpt372_port_ops = { static struct ata_port_operations hpt374_fn1_port_ops = { .inherits = &hpt372_port_ops, - .prereset = hpt374_fn1_pre_reset, + .cable_detect = hpt374_fn1_cable_detect, + .prereset = hpt37x_pre_reset, }; /** @@ -791,9 +799,8 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id) static const int MHz[4] = { 33, 40, 50, 66 }; void *private_data = NULL; const struct ata_port_info *ppi[] = { NULL, NULL }; - + u8 rev = dev->revision; u8 irqmask; - u32 class_rev; u8 mcr1; u32 freq; int prefer_dpll = 1; @@ -808,19 +815,16 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id) if (rc) return rc; - pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); - class_rev &= 0xFF; - if (dev->device == PCI_DEVICE_ID_TTI_HPT366) { /* May be a later chip in disguise. Check */ /* Older chips are in the HPT366 driver. Ignore them */ - if (class_rev < 3) + if (rev < 3) return -ENODEV; /* N series chips have their own driver. Ignore */ - if (class_rev == 6) + if (rev == 6) return -ENODEV; - switch(class_rev) { + switch(rev) { case 3: ppi[0] = &info_hpt370; chip_table = &hpt370; @@ -836,28 +840,29 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id) chip_table = &hpt372; break; default: - printk(KERN_ERR "pata_hpt37x: Unknown HPT366 subtype please report (%d).\n", class_rev); + printk(KERN_ERR "pata_hpt37x: Unknown HPT366 " + "subtype, please report (%d).\n", rev); return -ENODEV; } } else { switch(dev->device) { case PCI_DEVICE_ID_TTI_HPT372: /* 372N if rev >= 2*/ - if (class_rev >= 2) + if (rev >= 2) return -ENODEV; ppi[0] = &info_hpt372; chip_table = &hpt372a; break; case PCI_DEVICE_ID_TTI_HPT302: /* 302N if rev > 1 */ - if (class_rev > 1) + if (rev > 1) return -ENODEV; ppi[0] = &info_hpt372; /* Check this */ chip_table = &hpt302; break; case PCI_DEVICE_ID_TTI_HPT371: - if (class_rev > 1) + if (rev > 1) return -ENODEV; ppi[0] = &info_hpt372; chip_table = &hpt371; diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c index 3d59fe0a408..9a09a1b11ca 100644 --- a/drivers/ata/pata_hpt3x2n.c +++ b/drivers/ata/pata_hpt3x2n.c @@ -25,7 +25,7 @@ #include <linux/libata.h> #define DRV_NAME "pata_hpt3x2n" -#define DRV_VERSION "0.3.4" +#define DRV_VERSION "0.3.7" enum { HPT_PCI_FAST = (1 << 31), @@ -80,14 +80,13 @@ static struct hpt_clock hpt3x2n_clocks[] = { { XFER_MW_DMA_2, 0x2c829c62 }, { XFER_MW_DMA_1, 0x2c829c66 }, - { XFER_MW_DMA_0, 0x2c829d2c }, + { XFER_MW_DMA_0, 0x2c829d2e }, { XFER_PIO_4, 0x0c829c62 }, { XFER_PIO_3, 0x0c829c84 }, { XFER_PIO_2, 0x0c829ca6 }, { XFER_PIO_1, 0x0d029d26 }, { XFER_PIO_0, 0x0d029d5e }, - { 0, 0x0d029d5e } }; /** @@ -128,12 +127,15 @@ static int hpt3x2n_cable_detect(struct ata_port *ap) pci_read_config_byte(pdev, 0x5B, &scr2); pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01); + + udelay(10); /* debounce */ + /* Cable register now active */ pci_read_config_byte(pdev, 0x5A, &ata66); /* Restore state */ pci_write_config_byte(pdev, 0x5B, scr2); - if (ata66 & (1 << ap->port_no)) + if (ata66 & (2 >> ap->port_no)) return ATA_CBL_PATA40; else return ATA_CBL_PATA80; @@ -185,9 +187,8 @@ static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev) pci_read_config_dword(pdev, addr1, ®); mode = hpt3x2n_find_mode(ap, adev->pio_mode); - mode &= ~0x8000000; /* No FIFO in PIO */ - mode &= ~0x30070000; /* Leave config bits alone */ - reg &= 0x30070000; /* Strip timing bits */ + mode &= 0xCFC3FFFF; /* Leave DMA bits alone */ + reg &= ~0xCFC3FFFF; /* Strip timing bits */ pci_write_config_dword(pdev, addr1, reg | mode); } @@ -204,8 +205,7 @@ static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev) { struct pci_dev *pdev = to_pci_dev(ap->host->dev); u32 addr1, addr2; - u32 reg; - u32 mode; + u32 reg, mode, mask; u8 fast; addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); @@ -216,11 +216,12 @@ static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev) fast &= ~0x07; pci_write_config_byte(pdev, addr2, fast); + mask = adev->dma_mode < XFER_UDMA_0 ? 0x31C001FF : 0x303C0000; + pci_read_config_dword(pdev, addr1, ®); mode = hpt3x2n_find_mode(ap, adev->dma_mode); - mode |= 0x8000000; /* FIFO in MWDMA or UDMA */ - mode &= ~0xC0000000; /* Leave config bits alone */ - reg &= 0xC0000000; /* Strip timing bits */ + mode &= mask; + reg &= ~mask; pci_write_config_dword(pdev, addr1, reg | mode); } @@ -447,10 +448,8 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) .port_ops = &hpt3x2n_port_ops }; const struct ata_port_info *ppi[] = { &info, NULL }; - + u8 rev = dev->revision; u8 irqmask; - u32 class_rev; - unsigned int pci_mhz; unsigned int f_low, f_high; int adjust; @@ -462,26 +461,23 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id) if (rc) return rc; - pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); - class_rev &= 0xFF; - switch(dev->device) { case PCI_DEVICE_ID_TTI_HPT366: - if (class_rev < 6) + if (rev < 6) return -ENODEV; break; case PCI_DEVICE_ID_TTI_HPT371: - if (class_rev < 2) + if (rev < 2) return -ENODEV; /* 371N if rev > 1 */ break; case PCI_DEVICE_ID_TTI_HPT372: /* 372N if rev >= 2*/ - if (class_rev < 2) + if (rev < 2) return -ENODEV; break; case PCI_DEVICE_ID_TTI_HPT302: - if (class_rev < 2) + if (rev < 2) return -ENODEV; break; case PCI_DEVICE_ID_TTI_HPT372N: diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c index 7e310253b36..c86c71639a9 100644 --- a/drivers/ata/pata_hpt3x3.c +++ b/drivers/ata/pata_hpt3x3.c @@ -255,8 +255,17 @@ static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id) #ifdef CONFIG_PM static int hpt3x3_reinit_one(struct pci_dev *dev) { + struct ata_host *host = dev_get_drvdata(&dev->dev); + int rc; + + rc = ata_pci_device_do_resume(dev); + if (rc) + return rc; + hpt3x3_init_chipset(dev); - return ata_pci_device_resume(dev); + + ata_host_resume(host); + return 0; } #endif diff --git a/drivers/ata/pata_it8213.c b/drivers/ata/pata_it8213.c index f156da8076f..8f3325adceb 100644 --- a/drivers/ata/pata_it8213.c +++ b/drivers/ata/pata_it8213.c @@ -22,7 +22,7 @@ #define DRV_VERSION "0.0.3" /** - * it8213_pre_reset - check for 40/80 pin + * it8213_pre_reset - probe begin * @link: link * @deadline: deadline jiffies for the operation * @@ -92,18 +92,17 @@ static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev) { 2, 1 }, { 2, 3 }, }; - if (pio > 2) - control |= 1; /* TIME1 enable */ + if (pio > 1) + control |= 1; /* TIME */ if (ata_pio_need_iordy(adev)) /* PIO 3/4 require IORDY */ - control |= 2; /* IORDY enable */ + control |= 2; /* IE */ /* Bit 2 is set for ATAPI on the IT8213 - reverse of ICH/PIIX */ if (adev->class != ATA_DEV_ATA) - control |= 4; + control |= 4; /* PPE */ pci_read_config_word(dev, idetm_port, &idetm_data); - /* Enable PPE, IE and TIME as appropriate */ - + /* Set PPE, IE, and TIME as appropriate */ if (adev->devno == 0) { idetm_data &= 0xCCF0; idetm_data |= control; @@ -112,17 +111,17 @@ static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev) } else { u8 slave_data; - idetm_data &= 0xCC0F; + idetm_data &= 0xFF0F; idetm_data |= (control << 4); /* Slave timing in separate register */ pci_read_config_byte(dev, 0x44, &slave_data); slave_data &= 0xF0; - slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << 4; + slave_data |= (timings[pio][0] << 2) | timings[pio][1]; pci_write_config_byte(dev, 0x44, slave_data); } - idetm_data |= 0x4000; /* Ensure SITRE is enabled */ + idetm_data |= 0x4000; /* Ensure SITRE is set */ pci_write_config_word(dev, idetm_port, idetm_data); } @@ -173,10 +172,10 @@ static void it8213_set_dmamode (struct ata_port *ap, struct ata_device *adev) udma_enable |= (1 << devid); - /* Load the UDMA mode number */ + /* Load the UDMA cycle time */ pci_read_config_word(dev, 0x4A, &udma_timing); udma_timing &= ~(3 << (4 * devid)); - udma_timing |= (udma & 3) << (4 * devid); + udma_timing |= u_speed << (4 * devid); pci_write_config_word(dev, 0x4A, udma_timing); /* Load the clock selection */ @@ -211,7 +210,7 @@ static void it8213_set_dmamode (struct ata_port *ap, struct ata_device *adev) master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */ master_data |= control << 4; pci_read_config_byte(dev, 0x44, &slave_data); - slave_data &= (0x0F + 0xE1 * ap->port_no); + slave_data &= 0xF0; /* Load the matching timing */ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0); pci_write_config_byte(dev, 0x44, slave_data); @@ -263,7 +262,7 @@ static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *en static const struct ata_port_info info = { .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA2, + .mwdma_mask = ATA_MWDMA12_ONLY, .udma_mask = ATA_UDMA4, /* FIXME: want UDMA 100? */ .port_ops = &it8213_ops, }; diff --git a/drivers/ata/pata_it821x.c b/drivers/ata/pata_it821x.c index 188bc2fcd22..edc5c1fed15 100644 --- a/drivers/ata/pata_it821x.c +++ b/drivers/ata/pata_it821x.c @@ -955,7 +955,7 @@ static int it821x_reinit_one(struct pci_dev *pdev) static const struct pci_device_id it821x[] = { { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), }, { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), }, - { PCI_VDEVICE(RDC, 0x1010), }, + { PCI_VDEVICE(RDC, PCI_DEVICE_ID_RDC_D1010), }, { }, }; diff --git a/drivers/ata/pata_legacy.c b/drivers/ata/pata_legacy.c index 6932e56d179..9df1ff7e1ea 100644 --- a/drivers/ata/pata_legacy.c +++ b/drivers/ata/pata_legacy.c @@ -25,6 +25,13 @@ * http://www.ryston.cz/petr/vlb/pdc20230b.html * http://www.ryston.cz/petr/vlb/pdc20230c.html * http://www.ryston.cz/petr/vlb/pdc20630.html + * QDI65x0: + * http://www.ryston.cz/petr/vlb/qd6500.html + * http://www.ryston.cz/petr/vlb/qd6580.html + * + * QDI65x0 probe code based on drivers/ide/legacy/qd65xx.c + * Rewritten from the work of Colten Edwards <pje120@cs.usask.ca> by + * Samuel Thibault <samuel.thibault@ens-lyon.org> * * Unsupported but docs exist: * Appian/Adaptec AIC25VL01/Cirrus Logic PD7220 @@ -35,7 +42,7 @@ * the MPIIX where the tuning is PCI side but the IDE is "ISA side". * * Specific support is included for the ht6560a/ht6560b/opti82c611a/ - * opti82c465mv/promise 20230c/20630/winbond83759A + * opti82c465mv/promise 20230c/20630/qdi65x0/winbond83759A * * Use the autospeed and pio_mask options with: * Appian ADI/2 aka CLPD7220 or AIC25VL01. @@ -672,7 +679,7 @@ static void qdi6580dp_set_piomode(struct ata_port *ap, struct ata_device *adev) outb(timing, ld_qdi->timing + 2 * ap->port_no); /* Clear the FIFO */ if (adev->class != ATA_DEV_ATA) - outb(0x5F, ld_qdi->timing + 3); + outb(0x5F, (ld_qdi->timing & 0xFFF0) + 3); } /** @@ -707,7 +714,7 @@ static void qdi6580_set_piomode(struct ata_port *ap, struct ata_device *adev) outb(timing, ld_qdi->timing + 2 * adev->devno); /* Clear the FIFO */ if (adev->class != ATA_DEV_ATA) - outb(0x5F, ld_qdi->timing + 3); + outb(0x5F, (ld_qdi->timing & 0xFFF0) + 3); } /** @@ -787,6 +794,7 @@ static struct ata_port_operations qdi6580_port_ops = { static struct ata_port_operations qdi6580dp_port_ops = { .inherits = &legacy_base_port_ops, .set_piomode = qdi6580dp_set_piomode, + .qc_issue = qdi_qc_issue, .sff_data_xfer = vlb32_data_xfer, }; diff --git a/drivers/ata/pata_marvell.c b/drivers/ata/pata_marvell.c index 2096fb737f8..950da39cae3 100644 --- a/drivers/ata/pata_marvell.c +++ b/drivers/ata/pata_marvell.c @@ -58,7 +58,7 @@ static int marvell_pata_active(struct pci_dev *pdev) } /** - * marvell_pre_reset - check for 40/80 pin + * marvell_pre_reset - probe begin * @link: link * @deadline: deadline jiffies for the operation * diff --git a/drivers/ata/pata_ns87415.c b/drivers/ata/pata_ns87415.c index 773b1590b49..061aa1c41a4 100644 --- a/drivers/ata/pata_ns87415.c +++ b/drivers/ata/pata_ns87415.c @@ -325,6 +325,13 @@ static struct scsi_host_template ns87415_sht = { ATA_BMDMA_SHT(DRV_NAME), }; +static void ns87415_fixup(struct pci_dev *pdev) +{ + /* Select 512 byte sectors */ + pci_write_config_byte(pdev, 0x55, 0xEE); + /* Select PIO0 8bit clocking */ + pci_write_config_byte(pdev, 0x54, 0xB7); +} /** * ns87415_init_one - Register 87415 ATA PCI device with kernel services @@ -371,10 +378,8 @@ static int ns87415_init_one (struct pci_dev *pdev, const struct pci_device_id *e if (rc) return rc; - /* Select 512 byte sectors */ - pci_write_config_byte(pdev, 0x55, 0xEE); - /* Select PIO0 8bit clocking */ - pci_write_config_byte(pdev, 0x54, 0xB7); + ns87415_fixup(pdev); + return ata_pci_sff_init_one(pdev, ppi, &ns87415_sht, NULL); } @@ -384,6 +389,23 @@ static const struct pci_device_id ns87415_pci_tbl[] = { { } /* terminate list */ }; +#ifdef CONFIG_PM +static int ns87415_reinit_one(struct pci_dev *pdev) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + int rc; + + rc = ata_pci_device_do_resume(pdev); + if (rc) + return rc; + + ns87415_fixup(pdev); + + ata_host_resume(host); + return 0; +} +#endif + static struct pci_driver ns87415_pci_driver = { .name = DRV_NAME, .id_table = ns87415_pci_tbl, @@ -391,7 +413,7 @@ static struct pci_driver ns87415_pci_driver = { .remove = ata_pci_remove_one, #ifdef CONFIG_PM .suspend = ata_pci_device_suspend, - .resume = ata_pci_device_resume, + .resume = ns87415_reinit_one, #endif }; diff --git a/drivers/ata/pata_oldpiix.c b/drivers/ata/pata_oldpiix.c index 84ac5033ac8..9a8687db6b2 100644 --- a/drivers/ata/pata_oldpiix.c +++ b/drivers/ata/pata_oldpiix.c @@ -239,7 +239,7 @@ static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *e static const struct ata_port_info info = { .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA2, + .mwdma_mask = ATA_MWDMA12_ONLY, .port_ops = &oldpiix_pata_ops, }; const struct ata_port_info *ppi[] = { &info, NULL }; diff --git a/drivers/ata/pata_piccolo.c b/drivers/ata/pata_piccolo.c new file mode 100644 index 00000000000..bfe0180f3ef --- /dev/null +++ b/drivers/ata/pata_piccolo.c @@ -0,0 +1,140 @@ +/* + * pata_piccolo.c - Toshiba Piccolo PATA/SATA controller driver. + * + * This is basically an update to ata_generic.c to add Toshiba Piccolo support + * then split out to keep ata_generic "clean". + * + * Copyright 2005 Red Hat Inc, all rights reserved. + * + * Elements from ide/pci/generic.c + * Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org> + * Portions (C) Copyright 2002 Red Hat Inc <alan@redhat.com> + * + * May be copied or modified under the terms of the GNU General Public License + * + * The timing data tables/programming info are courtesy of the NetBSD driver + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_piccolo" +#define DRV_VERSION "0.0.1" + + + +static void tosh_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + static const u16 pio[6] = { /* For reg 0x50 low word & E088 */ + 0x0566, 0x0433, 0x0311, 0x0201, 0x0200, 0x0100 + }; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u16 conf; + pci_read_config_word(pdev, 0x50, &conf); + conf &= 0xE088; + conf |= pio[adev->pio_mode - XFER_PIO_0]; + pci_write_config_word(pdev, 0x50, conf); +} + +static void tosh_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 conf; + pci_read_config_dword(pdev, 0x5C, &conf); + conf &= 0x78FFE088; /* Keep the other bits */ + if (adev->dma_mode >= XFER_UDMA_0) { + int udma = adev->dma_mode - XFER_UDMA_0; + conf |= 0x80000000; + conf |= (udma + 2) << 28; + conf |= (2 - udma) * 0x111; /* spread into three nibbles */ + } else { + static const u32 mwdma[4] = { + 0x0655, 0x0200, 0x0200, 0x0100 + }; + conf |= mwdma[adev->dma_mode - XFER_MW_DMA_0]; + } + pci_write_config_dword(pdev, 0x5C, conf); +} + + +static struct scsi_host_template tosh_sht = { + ATA_BMDMA_SHT(DRV_NAME), +}; + +static struct ata_port_operations tosh_port_ops = { + .inherits = &ata_bmdma_port_ops, + .cable_detect = ata_cable_unknown, + .set_piomode = tosh_set_piomode, + .set_dmamode = tosh_set_dmamode +}; + +/** + * ata_tosh_init - attach generic IDE + * @dev: PCI device found + * @id: match entry + * + * Called each time a matching IDE interface is found. We check if the + * interface is one we wish to claim and if so we perform any chip + * specific hacks then let the ATA layer do the heavy lifting. + */ + +static int ata_tosh_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static const struct ata_port_info info = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO5, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA2, + .port_ops = &tosh_port_ops + }; + const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info }; + /* Just one port for the moment */ + return ata_pci_sff_init_one(dev, ppi, &tosh_sht, NULL); +} + +static struct pci_device_id ata_tosh[] = { + { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_1), }, + { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_2), }, + { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_3), }, + { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_5), }, + { 0, }, +}; + +static struct pci_driver ata_tosh_pci_driver = { + .name = DRV_NAME, + .id_table = ata_tosh, + .probe = ata_tosh_init_one, + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM + .suspend = ata_pci_device_suspend, + .resume = ata_pci_device_resume, +#endif +}; + +static int __init ata_tosh_init(void) +{ + return pci_register_driver(&ata_tosh_pci_driver); +} + + +static void __exit ata_tosh_exit(void) +{ + pci_unregister_driver(&ata_tosh_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("Low level driver for Toshiba Piccolo ATA"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, ata_tosh); +MODULE_VERSION(DRV_VERSION); + +module_init(ata_tosh_init); +module_exit(ata_tosh_exit); + diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c index 4401b332eaa..4fd25e737d9 100644 --- a/drivers/ata/pata_radisys.c +++ b/drivers/ata/pata_radisys.c @@ -139,9 +139,9 @@ static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev) pci_read_config_byte(dev, 0x4A, &udma_mode); if (adev->xfer_mode == XFER_UDMA_2) - udma_mode &= ~ (1 << adev->devno); + udma_mode &= ~(2 << (adev->devno * 4)); else /* UDMA 4 */ - udma_mode |= (1 << adev->devno); + udma_mode |= (2 << (adev->devno * 4)); pci_write_config_byte(dev, 0x4A, udma_mode); diff --git a/drivers/ata/pata_rdc.c b/drivers/ata/pata_rdc.c index c843a1e07c4..237a24d41a2 100644 --- a/drivers/ata/pata_rdc.c +++ b/drivers/ata/pata_rdc.c @@ -284,7 +284,7 @@ static struct ata_port_info rdc_port_info = { .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = ATA_PIO4, - .mwdma_mask = ATA_MWDMA2, + .mwdma_mask = ATA_MWDMA12_ONLY, .udma_mask = ATA_UDMA5, .port_ops = &rdc_pata_ops, }; diff --git a/drivers/ata/pata_rz1000.c b/drivers/ata/pata_rz1000.c index a5e4dfe60b4..2932998fc4c 100644 --- a/drivers/ata/pata_rz1000.c +++ b/drivers/ata/pata_rz1000.c @@ -105,11 +105,20 @@ static int rz1000_init_one (struct pci_dev *pdev, const struct pci_device_id *en #ifdef CONFIG_PM static int rz1000_reinit_one(struct pci_dev *pdev) { + struct ata_host *host = dev_get_drvdata(&pdev->dev); + int rc; + + rc = ata_pci_device_do_resume(pdev); + if (rc) + return rc; + /* If this fails on resume (which is a "cant happen" case), we must stop as any progress risks data loss */ if (rz1000_fifo_disable(pdev)) panic("rz1000 fifo"); - return ata_pci_device_resume(pdev); + + ata_host_resume(host); + return 0; } #endif diff --git a/drivers/ata/pata_sil680.c b/drivers/ata/pata_sil680.c index 4cb649d8d38..a2ace48a461 100644 --- a/drivers/ata/pata_sil680.c +++ b/drivers/ata/pata_sil680.c @@ -212,13 +212,11 @@ static struct ata_port_operations sil680_port_ops = { static u8 sil680_init_chip(struct pci_dev *pdev, int *try_mmio) { - u32 class_rev = 0; u8 tmpbyte = 0; - pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class_rev); - class_rev &= 0xff; /* FIXME: double check */ - pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, (class_rev) ? 1 : 255); + pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, + pdev->revision ? 1 : 255); pci_write_config_byte(pdev, 0x80, 0x00); pci_write_config_byte(pdev, 0x84, 0x00); diff --git a/drivers/ata/pata_sis.c b/drivers/ata/pata_sis.c index 488e77bcd22..5c30d56dec8 100644 --- a/drivers/ata/pata_sis.c +++ b/drivers/ata/pata_sis.c @@ -2,7 +2,7 @@ * pata_sis.c - SiS ATA driver * * (C) 2005 Red Hat - * (C) 2007 Bartlomiej Zolnierkiewicz + * (C) 2007,2009 Bartlomiej Zolnierkiewicz * * Based upon linux/drivers/ide/pci/sis5513.c * Copyright (C) 1999-2000 Andre Hedrick <andre@linux-ide.org> @@ -829,6 +829,23 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) return ata_pci_sff_init_one(pdev, ppi, &sis_sht, chipset); } +#ifdef CONFIG_PM +static int sis_reinit_one(struct pci_dev *pdev) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + int rc; + + rc = ata_pci_device_do_resume(pdev); + if (rc) + return rc; + + sis_fixup(pdev, host->private_data); + + ata_host_resume(host); + return 0; +} +#endif + static const struct pci_device_id sis_pci_tbl[] = { { PCI_VDEVICE(SI, 0x5513), }, /* SiS 5513 */ { PCI_VDEVICE(SI, 0x5518), }, /* SiS 5518 */ @@ -844,7 +861,7 @@ static struct pci_driver sis_pci_driver = { .remove = ata_pci_remove_one, #ifdef CONFIG_PM .suspend = ata_pci_device_suspend, - .resume = ata_pci_device_resume, + .resume = sis_reinit_one, #endif }; diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c index 88984b803d6..0d97890af68 100644 --- a/drivers/ata/pata_via.c +++ b/drivers/ata/pata_via.c @@ -303,14 +303,21 @@ static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, int mo } /* Set UDMA unless device is not UDMA capable */ - if (udma_type && t.udma) { - u8 cable80_status; + if (udma_type) { + u8 udma_etc; - /* Get 80-wire cable detection bit */ - pci_read_config_byte(pdev, 0x50 + offset, &cable80_status); - cable80_status &= 0x10; + pci_read_config_byte(pdev, 0x50 + offset, &udma_etc); - pci_write_config_byte(pdev, 0x50 + offset, ut | cable80_status); + /* clear transfer mode bit */ + udma_etc &= ~0x20; + + if (t.udma) { + /* preserve 80-wire cable detection bit */ + udma_etc &= 0x10; + udma_etc |= ut; + } + + pci_write_config_byte(pdev, 0x50 + offset, udma_etc); } } @@ -337,6 +344,32 @@ static void via_set_dmamode(struct ata_port *ap, struct ata_device *adev) } /** + * via_mode_filter - filter buggy device/mode pairs + * @dev: ATA device + * @mask: Mode bitmask + * + * We need to apply some minimal filtering for old controllers and at least + * one breed of Transcend SSD. Return the updated mask. + */ + +static unsigned long via_mode_filter(struct ata_device *dev, unsigned long mask) +{ + struct ata_host *host = dev->link->ap->host; + const struct via_isa_bridge *config = host->private_data; + unsigned char model_num[ATA_ID_PROD_LEN + 1]; + + if (config->id == PCI_DEVICE_ID_VIA_82C586_0) { + ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num)); + if (strcmp(model_num, "TS64GSSD25-M") == 0) { + ata_dev_printk(dev, KERN_WARNING, + "disabling UDMA mode due to reported lockups with this device.\n"); + mask &= ~ ATA_MASK_UDMA; + } + } + return ata_bmdma_mode_filter(dev, mask); +} + +/** * via_tf_load - send taskfile registers to host controller * @ap: Port to which output is sent * @tf: ATA taskfile register set @@ -427,6 +460,7 @@ static struct ata_port_operations via_port_ops = { .prereset = via_pre_reset, .sff_tf_load = via_tf_load, .port_start = via_port_start, + .mode_filter = via_mode_filter, }; static struct ata_port_operations via_port_ops_noirq = { @@ -526,7 +560,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id) .port_ops = &via_port_ops }; const struct ata_port_info *ppi[] = { NULL, NULL }; - struct pci_dev *isa = NULL; + struct pci_dev *isa; const struct via_isa_bridge *config; static int printed_version; u8 enable; @@ -551,15 +585,13 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id) if ((isa = pci_get_device(PCI_VENDOR_ID_VIA + !!(config->flags & VIA_BAD_ID), config->id, NULL))) { + u8 rev = isa->revision; + pci_dev_put(isa); - if (isa->revision >= config->rev_min && - isa->revision <= config->rev_max) + if (rev >= config->rev_min && rev <= config->rev_max) break; - pci_dev_put(isa); } - pci_dev_put(isa); - if (!(config->flags & VIA_NO_ENABLES)) { /* 0x40 low bits indicate enabled channels */ pci_read_config_byte(pdev, 0x40 , &enable); diff --git a/drivers/ata/sata_fsl.c b/drivers/ata/sata_fsl.c index 172b57e6543..8a5d35b759d 100644 --- a/drivers/ata/sata_fsl.c +++ b/drivers/ata/sata_fsl.c @@ -34,7 +34,7 @@ enum { SATA_FSL_HOST_FLAGS = (ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA | - ATA_FLAG_PMP | ATA_FLAG_NCQ), + ATA_FLAG_PMP | ATA_FLAG_NCQ | ATA_FLAG_AN), SATA_FSL_MAX_CMDS = SATA_FSL_QUEUE_DEPTH, SATA_FSL_CMD_HDR_SIZE = 16, /* 4 DWORDS */ @@ -132,7 +132,7 @@ enum { INT_ON_SINGL_DEVICE_ERR = (1 << 1), INT_ON_CMD_COMPLETE = 1, - INT_ON_ERROR = INT_ON_FATAL_ERR | + INT_ON_ERROR = INT_ON_FATAL_ERR | INT_ON_SNOTIFY_UPDATE | INT_ON_PHYRDY_CHG | INT_ON_SINGL_DEVICE_ERR, /* @@ -153,7 +153,7 @@ enum { IE_ON_CMD_COMPLETE = 1, DEFAULT_PORT_IRQ_ENABLE_MASK = IE_ON_FATAL_ERR | IE_ON_PHYRDY_CHG | - IE_ON_SIGNATURE_UPDATE | + IE_ON_SIGNATURE_UPDATE | IE_ON_SNOTIFY_UPDATE | IE_ON_SINGL_DEVICE_ERR | IE_ON_CMD_COMPLETE, EXT_INDIRECT_SEG_PRD_FLAG = (1 << 31), @@ -992,9 +992,8 @@ static void sata_fsl_error_intr(struct ata_port *ap) */ sata_fsl_scr_read(&ap->link, SCR_ERROR, &SError); - if (unlikely(SError & 0xFFFF0000)) { + if (unlikely(SError & 0xFFFF0000)) sata_fsl_scr_write(&ap->link, SCR_ERROR, SError); - } DPRINTK("error_intr,hStat=0x%x,CE=0x%x,DE =0x%x,SErr=0x%x\n", hstatus, cereg, ioread32(hcr_base + DE), SError); @@ -1007,6 +1006,10 @@ static void sata_fsl_error_intr(struct ata_port *ap) freeze = 1; } + /* Handle SDB FIS receive & notify update */ + if (hstatus & INT_ON_SNOTIFY_UPDATE) + sata_async_notification(ap); + /* Handle PHYRDY change notification */ if (hstatus & INT_ON_PHYRDY_CHG) { DPRINTK("SATA FSL: PHYRDY change indication\n"); @@ -1070,9 +1073,9 @@ static void sata_fsl_error_intr(struct ata_port *ap) } /* record error info */ - if (qc) { + if (qc) qc->err_mask |= err_mask; - } else + else ehi->err_mask |= err_mask; ehi->action |= action; @@ -1103,7 +1106,6 @@ static void sata_fsl_host_intr(struct ata_port *ap) if (unlikely(SError & 0xFFFF0000)) { DPRINTK("serror @host_intr : 0x%x\n", SError); sata_fsl_error_intr(ap); - } if (unlikely(hstatus & INT_ON_ERROR)) { diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index 6f5093b7c8c..a8a7be0d06f 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -2217,7 +2217,7 @@ static unsigned int mv_qc_issue_fis(struct ata_queued_cmd *qc) int err = 0; ata_tf_to_fis(&qc->tf, link->pmp, 1, (void *)fis); - err = mv_send_fis(ap, fis, sizeof(fis) / sizeof(fis[0])); + err = mv_send_fis(ap, fis, ARRAY_SIZE(fis)); if (err) return err; diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c index e6946fc527d..1370df6c420 100644 --- a/drivers/ata/sata_sil24.c +++ b/drivers/ata/sata_sil24.c @@ -417,6 +417,10 @@ static struct ata_port_operations sil24_ops = { #endif }; +static int sata_sil24_msi; /* Disable MSI */ +module_param_named(msi, sata_sil24_msi, bool, S_IRUGO); +MODULE_PARM_DESC(msi, "Enable MSI (Default: false)"); + /* * Use bits 30-31 of port_flags to encode available port numbers. * Current maxium is 4. @@ -1340,6 +1344,11 @@ static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) sil24_init_controller(host); + if (sata_sil24_msi && !pci_enable_msi(pdev)) { + dev_printk(KERN_INFO, &pdev->dev, "Using MSI\n"); + pci_intx(pdev, 0); + } + pci_set_master(pdev); return ata_host_activate(host, pdev->irq, sil24_interrupt, IRQF_SHARED, &sil24_sht); diff --git a/drivers/ide/ide-pci-generic.c b/drivers/ide/ide-pci-generic.c index 39d4e01f5c9..a743e68a890 100644 --- a/drivers/ide/ide-pci-generic.c +++ b/drivers/ide/ide-pci-generic.c @@ -162,9 +162,10 @@ static const struct pci_device_id generic_pci_tbl[] = { #ifdef CONFIG_BLK_DEV_IDE_SATA { PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_8237_SATA), 5 }, #endif - { PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO), 4 }, { PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_1), 4 }, { PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_2), 4 }, + { PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_3), 4 }, + { PCI_VDEVICE(TOSHIBA, PCI_DEVICE_ID_TOSHIBA_PICCOLO_5), 4 }, { PCI_VDEVICE(NETCELL, PCI_DEVICE_ID_REVOLUTION), 6 }, /* * Must come last. If you add entries adjust |