diff options
Diffstat (limited to 'drivers')
84 files changed, 1547 insertions, 2409 deletions
diff --git a/drivers/Makefile b/drivers/Makefile index 619dd964c51..5c69b86db62 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -69,7 +69,7 @@ obj-$(CONFIG_EISA) += eisa/ obj-$(CONFIG_CPU_FREQ) += cpufreq/ obj-$(CONFIG_MMC) += mmc/ obj-$(CONFIG_INFINIBAND) += infiniband/ -obj-$(CONFIG_SGI_IOC4) += sn/ +obj-$(CONFIG_SGI_SN) += sn/ obj-y += firmware/ obj-$(CONFIG_CRYPTO) += crypto/ obj-$(CONFIG_SUPERH) += sh/ diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c index 12d7b9bdfa9..0d65394707d 100644 --- a/drivers/block/cciss.c +++ b/drivers/block/cciss.c @@ -2183,6 +2183,7 @@ static void cciss_softirq_done(struct request *rq) { CommandList_struct *cmd = rq->completion_data; ctlr_info_t *h = hba[cmd->ctlr]; + unsigned long flags; u64bit temp64; int i, ddir; @@ -2205,10 +2206,10 @@ static void cciss_softirq_done(struct request *rq) printk("Done with %p\n", rq); #endif /* CCISS_DEBUG */ - spin_lock_irq(&h->lock); + spin_lock_irqsave(&h->lock, flags); end_that_request_last(rq, rq->errors); cmd_free(h, cmd,1); - spin_unlock_irq(&h->lock); + spin_unlock_irqrestore(&h->lock, flags); } /* checks the status of the job and calls complete buffers to mark all diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index c5829591436..7230d4e0819 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -113,6 +113,16 @@ config SENSORS_DS1621 This driver can also be built as a module. If so, the module will be called ds1621. +config SENSORS_F71805F + tristate "Fintek F71805F/FG" + depends on HWMON && EXPERIMENTAL + help + If you say yes here you get support for hardware monitoring + features of the Fintek F71805F/FG chips. + + This driver can also be built as a module. If so, the module + will be called f71805f. + config SENSORS_FSCHER tristate "FSC Hermes" depends on HWMON && I2C && EXPERIMENTAL diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 06d4a1d1410..fbdb8d911a7 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -18,6 +18,7 @@ obj-$(CONFIG_SENSORS_ADM1031) += adm1031.o obj-$(CONFIG_SENSORS_ADM9240) += adm9240.o obj-$(CONFIG_SENSORS_ATXP1) += atxp1.o obj-$(CONFIG_SENSORS_DS1621) += ds1621.o +obj-$(CONFIG_SENSORS_F71805F) += f71805f.o obj-$(CONFIG_SENSORS_FSCHER) += fscher.o obj-$(CONFIG_SENSORS_FSCPOS) += fscpos.o obj-$(CONFIG_SENSORS_GL518SM) += gl518sm.o diff --git a/drivers/hwmon/f71805f.c b/drivers/hwmon/f71805f.c new file mode 100644 index 00000000000..e029e0a94ec --- /dev/null +++ b/drivers/hwmon/f71805f.c @@ -0,0 +1,908 @@ +/* + * f71805f.c - driver for the Fintek F71805F/FG Super-I/O chip integrated + * hardware monitoring features + * Copyright (C) 2005 Jean Delvare <khali@linux-fr.org> + * + * The F71805F/FG is a LPC Super-I/O chip made by Fintek. It integrates + * complete hardware monitoring features: voltage, fan and temperature + * sensors, and manual and automatic fan speed control. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/jiffies.h> +#include <linux/platform_device.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/err.h> +#include <asm/io.h> + +static struct platform_device *pdev; + +#define DRVNAME "f71805f" + +/* + * Super-I/O constants and functions + */ + +#define F71805F_LD_HWM 0x04 + +#define SIO_REG_LDSEL 0x07 /* Logical device select */ +#define SIO_REG_DEVID 0x20 /* Device ID (2 bytes) */ +#define SIO_REG_DEVREV 0x22 /* Device revision */ +#define SIO_REG_MANID 0x23 /* Fintek ID (2 bytes) */ +#define SIO_REG_ENABLE 0x30 /* Logical device enable */ +#define SIO_REG_ADDR 0x60 /* Logical device address (2 bytes) */ + +#define SIO_FINTEK_ID 0x1934 +#define SIO_F71805F_ID 0x0406 + +static inline int +superio_inb(int base, int reg) +{ + outb(reg, base); + return inb(base + 1); +} + +static int +superio_inw(int base, int reg) +{ + int val; + outb(reg++, base); + val = inb(base + 1) << 8; + outb(reg, base); + val |= inb(base + 1); + return val; +} + +static inline void +superio_select(int base, int ld) +{ + outb(SIO_REG_LDSEL, base); + outb(ld, base + 1); +} + +static inline void +superio_enter(int base) +{ + outb(0x87, base); + outb(0x87, base); +} + +static inline void +superio_exit(int base) +{ + outb(0xaa, base); +} + +/* + * ISA constants + */ + +#define REGION_LENGTH 2 +#define ADDR_REG_OFFSET 0 +#define DATA_REG_OFFSET 1 + +static struct resource f71805f_resource __initdata = { + .flags = IORESOURCE_IO, +}; + +/* + * Registers + */ + +/* in nr from 0 to 8 (8-bit values) */ +#define F71805F_REG_IN(nr) (0x10 + (nr)) +#define F71805F_REG_IN_HIGH(nr) (0x40 + 2 * (nr)) +#define F71805F_REG_IN_LOW(nr) (0x41 + 2 * (nr)) +/* fan nr from 0 to 2 (12-bit values, two registers) */ +#define F71805F_REG_FAN(nr) (0x20 + 2 * (nr)) +#define F71805F_REG_FAN_LOW(nr) (0x28 + 2 * (nr)) +#define F71805F_REG_FAN_CTRL(nr) (0x60 + 16 * (nr)) +/* temp nr from 0 to 2 (8-bit values) */ +#define F71805F_REG_TEMP(nr) (0x1B + (nr)) +#define F71805F_REG_TEMP_HIGH(nr) (0x54 + 2 * (nr)) +#define F71805F_REG_TEMP_HYST(nr) (0x55 + 2 * (nr)) +#define F71805F_REG_TEMP_MODE 0x01 + +#define F71805F_REG_START 0x00 +/* status nr from 0 to 2 */ +#define F71805F_REG_STATUS(nr) (0x36 + (nr)) + +/* + * Data structures and manipulation thereof + */ + +struct f71805f_data { + unsigned short addr; + const char *name; + struct semaphore lock; + struct class_device *class_dev; + + struct semaphore update_lock; + char valid; /* !=0 if following fields are valid */ + unsigned long last_updated; /* In jiffies */ + unsigned long last_limits; /* In jiffies */ + + /* Register values */ + u8 in[9]; + u8 in_high[9]; + u8 in_low[9]; + u16 fan[3]; + u16 fan_low[3]; + u8 fan_enabled; /* Read once at init time */ + u8 temp[3]; + u8 temp_high[3]; + u8 temp_hyst[3]; + u8 temp_mode; + u8 alarms[3]; +}; + +static inline long in_from_reg(u8 reg) +{ + return (reg * 8); +} + +/* The 2 least significant bits are not used */ +static inline u8 in_to_reg(long val) +{ + if (val <= 0) + return 0; + if (val >= 2016) + return 0xfc; + return (((val + 16) / 32) << 2); +} + +/* in0 is downscaled by a factor 2 internally */ +static inline long in0_from_reg(u8 reg) +{ + return (reg * 16); +} + +static inline u8 in0_to_reg(long val) +{ + if (val <= 0) + return 0; + if (val >= 4032) + return 0xfc; + return (((val + 32) / 64) << 2); +} + +/* The 4 most significant bits are not used */ +static inline long fan_from_reg(u16 reg) +{ + reg &= 0xfff; + if (!reg || reg == 0xfff) + return 0; + return (1500000 / reg); +} + +static inline u16 fan_to_reg(long rpm) +{ + /* If the low limit is set below what the chip can measure, + store the largest possible 12-bit value in the registers, + so that no alarm will ever trigger. */ + if (rpm < 367) + return 0xfff; + return (1500000 / rpm); +} + +static inline long temp_from_reg(u8 reg) +{ + return (reg * 1000); +} + +static inline u8 temp_to_reg(long val) +{ + if (val < 0) + val = 0; + else if (val > 1000 * 0xff) + val = 0xff; + return ((val + 500) / 1000); +} + +/* + * Device I/O access + */ + +static u8 f71805f_read8(struct f71805f_data *data, u8 reg) +{ + u8 val; + + down(&data->lock); + outb(reg, data->addr + ADDR_REG_OFFSET); + val = inb(data->addr + DATA_REG_OFFSET); + up(&data->lock); + + return val; +} + +static void f71805f_write8(struct f71805f_data *data, u8 reg, u8 val) +{ + down(&data->lock); + outb(reg, data->addr + ADDR_REG_OFFSET); + outb(val, data->addr + DATA_REG_OFFSET); + up(&data->lock); +} + +/* It is important to read the MSB first, because doing so latches the + value of the LSB, so we are sure both bytes belong to the same value. */ +static u16 f71805f_read16(struct f71805f_data *data, u8 reg) +{ + u16 val; + + down(&data->lock); + outb(reg, data->addr + ADDR_REG_OFFSET); + val = inb(data->addr + DATA_REG_OFFSET) << 8; + outb(++reg, data->addr + ADDR_REG_OFFSET); + val |= inb(data->addr + DATA_REG_OFFSET); + up(&data->lock); + + return val; +} + +static void f71805f_write16(struct f71805f_data *data, u8 reg, u16 val) +{ + down(&data->lock); + outb(reg, data->addr + ADDR_REG_OFFSET); + outb(val >> 8, data->addr + DATA_REG_OFFSET); + outb(++reg, data->addr + ADDR_REG_OFFSET); + outb(val & 0xff, data->addr + DATA_REG_OFFSET); + up(&data->lock); +} + +static struct f71805f_data *f71805f_update_device(struct device *dev) +{ + struct f71805f_data *data = dev_get_drvdata(dev); + int nr; + + down(&data->update_lock); + + /* Limit registers cache is refreshed after 60 seconds */ + if (time_after(jiffies, data->last_updated + 60 * HZ) + || !data->valid) { + for (nr = 0; nr < 9; nr++) { + data->in_high[nr] = f71805f_read8(data, + F71805F_REG_IN_HIGH(nr)); + data->in_low[nr] = f71805f_read8(data, + F71805F_REG_IN_LOW(nr)); + } + for (nr = 0; nr < 3; nr++) { + if (data->fan_enabled & (1 << nr)) + data->fan_low[nr] = f71805f_read16(data, + F71805F_REG_FAN_LOW(nr)); + } + for (nr = 0; nr < 3; nr++) { + data->temp_high[nr] = f71805f_read8(data, + F71805F_REG_TEMP_HIGH(nr)); + data->temp_hyst[nr] = f71805f_read8(data, + F71805F_REG_TEMP_HYST(nr)); + } + data->temp_mode = f71805f_read8(data, F71805F_REG_TEMP_MODE); + + data->last_limits = jiffies; + } + + /* Measurement registers cache is refreshed after 1 second */ + if (time_after(jiffies, data->last_updated + HZ) + || !data->valid) { + for (nr = 0; nr < 9; nr++) { + data->in[nr] = f71805f_read8(data, + F71805F_REG_IN(nr)); + } + for (nr = 0; nr < 3; nr++) { + if (data->fan_enabled & (1 << nr)) + data->fan[nr] = f71805f_read16(data, + F71805F_REG_FAN(nr)); + } + for (nr = 0; nr < 3; nr++) { + data->temp[nr] = f71805f_read8(data, + F71805F_REG_TEMP(nr)); + } + for (nr = 0; nr < 3; nr++) { + data->alarms[nr] = f71805f_read8(data, + F71805F_REG_STATUS(nr)); + } + + data->last_updated = jiffies; + data->valid = 1; + } + + up(&data->update_lock); + + return data; +} + +/* + * Sysfs interface + */ + +static ssize_t show_in0(struct device *dev, struct device_attribute *devattr, + char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + + return sprintf(buf, "%ld\n", in0_from_reg(data->in[0])); +} + +static ssize_t show_in0_max(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + + return sprintf(buf, "%ld\n", in0_from_reg(data->in_high[0])); +} + +static ssize_t show_in0_min(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + + return sprintf(buf, "%ld\n", in0_from_reg(data->in_low[0])); +} + +static ssize_t set_in0_max(struct device *dev, struct device_attribute + *devattr, const char *buf, size_t count) +{ + struct f71805f_data *data = dev_get_drvdata(dev); + long val = simple_strtol(buf, NULL, 10); + + down(&data->update_lock); + data->in_high[0] = in0_to_reg(val); + f71805f_write8(data, F71805F_REG_IN_HIGH(0), data->in_high[0]); + up(&data->update_lock); + + return count; +} + +static ssize_t set_in0_min(struct device *dev, struct device_attribute + *devattr, const char *buf, size_t count) +{ + struct f71805f_data *data = dev_get_drvdata(dev); + long val = simple_strtol(buf, NULL, 10); + + down(&data->update_lock); + data->in_low[0] = in0_to_reg(val); + f71805f_write8(data, F71805F_REG_IN_LOW(0), data->in_low[0]); + up(&data->update_lock); + + return count; +} + +static DEVICE_ATTR(in0_input, S_IRUGO, show_in0, NULL); +static DEVICE_ATTR(in0_max, S_IRUGO| S_IWUSR, show_in0_max, set_in0_max); +static DEVICE_ATTR(in0_min, S_IRUGO| S_IWUSR, show_in0_min, set_in0_min); + +static ssize_t show_in(struct device *dev, struct device_attribute *devattr, + char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + + return sprintf(buf, "%ld\n", in_from_reg(data->in[nr])); +} + +static ssize_t show_in_max(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + + return sprintf(buf, "%ld\n", in_from_reg(data->in_high[nr])); +} + +static ssize_t show_in_min(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + + return sprintf(buf, "%ld\n", in_from_reg(data->in_low[nr])); +} + +static ssize_t set_in_max(struct device *dev, struct device_attribute + *devattr, const char *buf, size_t count) +{ + struct f71805f_data *data = dev_get_drvdata(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + long val = simple_strtol(buf, NULL, 10); + + down(&data->update_lock); + data->in_high[nr] = in_to_reg(val); + f71805f_write8(data, F71805F_REG_IN_HIGH(nr), data->in_high[nr]); + up(&data->update_lock); + + return count; +} + +static ssize_t set_in_min(struct device *dev, struct device_attribute + *devattr, const char *buf, size_t count) +{ + struct f71805f_data *data = dev_get_drvdata(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + long val = simple_strtol(buf, NULL, 10); + + down(&data->update_lock); + data->in_low[nr] = in_to_reg(val); + f71805f_write8(data, F71805F_REG_IN_LOW(nr), data->in_low[nr]); + up(&data->update_lock); + + return count; +} + +#define sysfs_in(offset) \ +static SENSOR_DEVICE_ATTR(in##offset##_input, S_IRUGO, \ + show_in, NULL, offset); \ +static SENSOR_DEVICE_ATTR(in##offset##_max, S_IRUGO | S_IWUSR, \ + show_in_max, set_in_max, offset); \ +static SENSOR_DEVICE_ATTR(in##offset##_min, S_IRUGO | S_IWUSR, \ + show_in_min, set_in_min, offset) + +sysfs_in(1); +sysfs_in(2); +sysfs_in(3); +sysfs_in(4); +sysfs_in(5); +sysfs_in(6); +sysfs_in(7); +sysfs_in(8); + +static ssize_t show_fan(struct device *dev, struct device_attribute *devattr, + char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + + return sprintf(buf, "%ld\n", fan_from_reg(data->fan[nr])); +} + +static ssize_t show_fan_min(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + + return sprintf(buf, "%ld\n", fan_from_reg(data->fan_low[nr])); +} + +static ssize_t set_fan_min(struct device *dev, struct device_attribute + *devattr, const char *buf, size_t count) +{ + struct f71805f_data *data = dev_get_drvdata(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + long val = simple_strtol(buf, NULL, 10); + + down(&data->update_lock); + data->fan_low[nr] = fan_to_reg(val); + f71805f_write16(data, F71805F_REG_FAN_LOW(nr), data->fan_low[nr]); + up(&data->update_lock); + + return count; +} + +#define sysfs_fan(offset) \ +static SENSOR_DEVICE_ATTR(fan##offset##_input, S_IRUGO, \ + show_fan, NULL, offset - 1); \ +static SENSOR_DEVICE_ATTR(fan##offset##_min, S_IRUGO | S_IWUSR, \ + show_fan_min, set_fan_min, offset - 1) + +sysfs_fan(1); +sysfs_fan(2); +sysfs_fan(3); + +static ssize_t show_temp(struct device *dev, struct device_attribute *devattr, + char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + + return sprintf(buf, "%ld\n", temp_from_reg(data->temp[nr])); +} + +static ssize_t show_temp_max(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + + return sprintf(buf, "%ld\n", temp_from_reg(data->temp_high[nr])); +} + +static ssize_t show_temp_hyst(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + + return sprintf(buf, "%ld\n", temp_from_reg(data->temp_hyst[nr])); +} + +static ssize_t show_temp_type(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + + /* 3 is diode, 4 is thermistor */ + return sprintf(buf, "%u\n", (data->temp_mode & (1 << nr)) ? 3 : 4); +} + +static ssize_t set_temp_max(struct device *dev, struct device_attribute + *devattr, const char *buf, size_t count) +{ + struct f71805f_data *data = dev_get_drvdata(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + long val = simple_strtol(buf, NULL, 10); + + down(&data->update_lock); + data->temp_high[nr] = temp_to_reg(val); + f71805f_write8(data, F71805F_REG_TEMP_HIGH(nr), data->temp_high[nr]); + up(&data->update_lock); + + return count; +} + +static ssize_t set_temp_hyst(struct device *dev, struct device_attribute + *devattr, const char *buf, size_t count) +{ + struct f71805f_data *data = dev_get_drvdata(dev); + struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); + int nr = attr->index; + long val = simple_strtol(buf, NULL, 10); + + down(&data->update_lock); + data->temp_hyst[nr] = temp_to_reg(val); + f71805f_write8(data, F71805F_REG_TEMP_HYST(nr), data->temp_hyst[nr]); + up(&data->update_lock); + + return count; +} + +#define sysfs_temp(offset) \ +static SENSOR_DEVICE_ATTR(temp##offset##_input, S_IRUGO, \ + show_temp, NULL, offset - 1); \ +static SENSOR_DEVICE_ATTR(temp##offset##_max, S_IRUGO | S_IWUSR, \ + show_temp_max, set_temp_max, offset - 1); \ +static SENSOR_DEVICE_ATTR(temp##offset##_max_hyst, S_IRUGO | S_IWUSR, \ + show_temp_hyst, set_temp_hyst, offset - 1); \ +static SENSOR_DEVICE_ATTR(temp##offset##_type, S_IRUGO, \ + show_temp_type, NULL, offset - 1) + +sysfs_temp(1); +sysfs_temp(2); +sysfs_temp(3); + +static ssize_t show_alarms_in(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + + return sprintf(buf, "%d\n", data->alarms[0] | + ((data->alarms[1] & 0x01) << 8)); +} + +static ssize_t show_alarms_fan(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + + return sprintf(buf, "%d\n", data->alarms[2] & 0x07); +} + +static ssize_t show_alarms_temp(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + struct f71805f_data *data = f71805f_update_device(dev); + + return sprintf(buf, "%d\n", (data->alarms[1] >> 3) & 0x07); +} + +static DEVICE_ATTR(alarms_in, S_IRUGO, show_alarms_in, NULL); +static DEVICE_ATTR(alarms_fan, S_IRUGO, show_alarms_fan, NULL); +static DEVICE_ATTR(alarms_temp, S_IRUGO, show_alarms_temp, NULL); + +static ssize_t show_name(struct device *dev, struct device_attribute + *devattr, char *buf) +{ + struct f71805f_data *data = dev_get_drvdata(dev); + + return sprintf(buf, "%s\n", data->name); +} + +static DEVICE_ATTR(name, S_IRUGO, show_name, NULL); + +/* + * Device registration and initialization + */ + +static void __devinit f71805f_init_device(struct f71805f_data *data) +{ + u8 reg; + int i; + + reg = f71805f_read8(data, F71805F_REG_START); + if ((reg & 0x41) != 0x01) { + printk(KERN_DEBUG DRVNAME ": Starting monitoring " + "operations\n"); + f71805f_write8(data, F71805F_REG_START, (reg | 0x01) & ~0x40); + } + + /* Fan monitoring can be disabled. If it is, we won't be polling + the register values, and won't create the related sysfs files. */ + for (i = 0; i < 3; i++) { + reg = f71805f_read8(data, F71805F_REG_FAN_CTRL(i)); + if (!(reg & 0x80)) + data->fan_enabled |= (1 << i); + } +} + +static int __devinit f71805f_probe(struct platform_device *pdev) +{ + struct f71805f_data *data; + struct resource *res; + int err; + + if (!(data = kzalloc(sizeof(struct f71805f_data), GFP_KERNEL))) { + err = -ENOMEM; + printk(KERN_ERR DRVNAME ": Out of memory\n"); + goto exit; + } + + res = platform_get_resource(pdev, IORESOURCE_IO, 0); + data->addr = res->start; + init_MUTEX(&data->lock); + data->name = "f71805f"; + init_MUTEX(&data->update_lock); + + platform_set_drvdata(pdev, data); + + data->class_dev = hwmon_device_register(&pdev->dev); + if (IS_ERR(data->class_dev)) { + err = PTR_ERR(data->class_dev); + dev_err(&pdev->dev, "Class registration failed (%d)\n", err); + goto exit_free; + } + + /* Initialize the F71805F chip */ + f71805f_init_device(data); + + /* Register sysfs interface files */ + device_create_file(&pdev->dev, &dev_attr_in0_input); + device_create_file(&pdev->dev, &dev_attr_in0_max); + device_create_file(&pdev->dev, &dev_attr_in0_min); + device_create_file(&pdev->dev, &sensor_dev_attr_in1_input.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in2_input.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in3_input.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in4_input.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in5_input.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in6_input.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in7_input.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in8_input.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in1_max.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in2_max.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in3_max.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in4_max.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in5_max.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in6_max.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in7_max.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in8_max.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in1_min.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in2_min.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in3_min.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in4_min.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in5_min.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in6_min.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in7_min.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_in8_min.dev_attr); + if (data->fan_enabled & (1 << 0)) { + device_create_file(&pdev->dev, + &sensor_dev_attr_fan1_input.dev_attr); + device_create_file(&pdev->dev, + &sensor_dev_attr_fan1_min.dev_attr); + } + if (data->fan_enabled & (1 << 1)) { + device_create_file(&pdev->dev, + &sensor_dev_attr_fan2_input.dev_attr); + device_create_file(&pdev->dev, + &sensor_dev_attr_fan2_min.dev_attr); + } + if (data->fan_enabled & (1 << 2)) { + device_create_file(&pdev->dev, + &sensor_dev_attr_fan3_input.dev_attr); + device_create_file(&pdev->dev, + &sensor_dev_attr_fan3_min.dev_attr); + } + device_create_file(&pdev->dev, + &sensor_dev_attr_temp1_input.dev_attr); + device_create_file(&pdev->dev, + &sensor_dev_attr_temp2_input.dev_attr); + device_create_file(&pdev->dev, + &sensor_dev_attr_temp3_input.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_temp1_max.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_temp2_max.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_temp3_max.dev_attr); + device_create_file(&pdev->dev, + &sensor_dev_attr_temp1_max_hyst.dev_attr); + device_create_file(&pdev->dev, + &sensor_dev_attr_temp2_max_hyst.dev_attr); + device_create_file(&pdev->dev, + &sensor_dev_attr_temp3_max_hyst.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_temp1_type.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_temp2_type.dev_attr); + device_create_file(&pdev->dev, &sensor_dev_attr_temp3_type.dev_attr); + device_create_file(&pdev->dev, &dev_attr_alarms_in); + device_create_file(&pdev->dev, &dev_attr_alarms_fan); + device_create_file(&pdev->dev, &dev_attr_alarms_temp); + device_create_file(&pdev->dev, &dev_attr_name); + + return 0; + +exit_free: + kfree(data); +exit: + return err; +} + +static int __devexit f71805f_remove(struct platform_device *pdev) +{ + struct f71805f_data *data = platform_get_drvdata(pdev); + + platform_set_drvdata(pdev, NULL); + hwmon_device_unregister(data->class_dev); + kfree(data); + + return 0; +} + +static struct platform_driver f71805f_driver = { + .driver = { + .owner = THIS_MODULE, + .name = DRVNAME, + }, + .probe = f71805f_probe, + .remove = __devexit_p(f71805f_remove), +}; + +static int __init f71805f_device_add(unsigned short address) +{ + int err; + + pdev = platform_device_alloc(DRVNAME, address); + if (!pdev) { + err = -ENOMEM; + printk(KERN_ERR DRVNAME ": Device allocation failed\n"); + goto exit; + } + + f71805f_resource.start = address; + f71805f_resource.end = address + REGION_LENGTH - 1; + f71805f_resource.name = pdev->name; + err = platform_device_add_resources(pdev, &f71805f_resource, 1); + if (err) { + printk(KERN_ERR DRVNAME ": Device resource addition failed " + "(%d)\n", err); + goto exit_device_put; + } + + err = platform_device_add(pdev); + if (err) { + printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n", + err); + goto exit_device_put; + } + + return 0; + +exit_device_put: + platform_device_put(pdev); +exit: + return err; +} + +static int __init f71805f_find(int sioaddr, unsigned short *address) +{ + int err = -ENODEV; + u16 devid; + + superio_enter(sioaddr); + + devid = superio_inw(sioaddr, SIO_REG_MANID); + if (devid != SIO_FINTEK_ID) + goto exit; + + devid = superio_inw(sioaddr, SIO_REG_DEVID); + if (devid != SIO_F71805F_ID) { + printk(KERN_INFO DRVNAME ": Unsupported Fintek device, " + "skipping\n"); + goto exit; + } + + superio_select(sioaddr, F71805F_LD_HWM); + if (!(superio_inb(sioaddr, SIO_REG_ENABLE) & 0x01)) { + printk(KERN_WARNING DRVNAME ": Device not activated, " + "skipping\n"); + goto exit; + } + + *address = superio_inw(sioaddr, SIO_REG_ADDR); + if (*address == 0) { + printk(KERN_WARNING DRVNAME ": Base address not set, " + "skipping\n"); + goto exit; + } + + err = 0; + printk(KERN_INFO DRVNAME ": Found F71805F chip at %#x, revision %u\n", + *address, superio_inb(sioaddr, SIO_REG_DEVREV)); + +exit: + superio_exit(sioaddr); + return err; +} + +static int __init f71805f_init(void) +{ + int err; + unsigned short address; + + if (f71805f_find(0x2e, &address) + && f71805f_find(0x4e, &address)) + return -ENODEV; + + err = platform_driver_register(&f71805f_driver); + if (err) + goto exit; + + /* Sets global pdev as a side effect */ + err = f71805f_device_add(address); + if (err) + goto exit_driver; + + return 0; + +exit_driver: + platform_driver_unregister(&f71805f_driver); +exit: + return err; +} + +static void __exit f71805f_exit(void) +{ + platform_device_unregister(pdev); + platform_driver_unregister(&f71805f_driver); +} + +MODULE_AUTHOR("Jean Delvare <khali@linux-fr>"); +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("F71805F hardware monitoring driver"); + +module_init(f71805f_init); +module_exit(f71805f_exit); diff --git a/drivers/hwmon/it87.c b/drivers/hwmon/it87.c index 0da7c9c508c..e87d52c5994 100644 --- a/drivers/hwmon/it87.c +++ b/drivers/hwmon/it87.c @@ -45,8 +45,7 @@ /* Addresses to scan */ -static unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d, - 0x2e, 0x2f, I2C_CLIENT_END }; +static unsigned short normal_i2c[] = { 0x2d, I2C_CLIENT_END }; static unsigned short isa_address; /* Insmod parameters */ @@ -830,6 +829,11 @@ static int it87_detect(struct i2c_adapter *adapter, int address, int kind) if ((err = i2c_attach_client(new_client))) goto ERROR2; + if (!is_isa) + dev_info(&new_client->dev, "The I2C interface to IT87xxF " + "hardware monitoring chips is deprecated. Please " + "report if you still rely on it.\n"); + /* Check PWM configuration */ enable_pwm_interface = it87_check_pwm(new_client); diff --git a/drivers/hwmon/lm77.c b/drivers/hwmon/lm77.c index a2f420d01fb..df9e02aaa70 100644 --- a/drivers/hwmon/lm77.c +++ b/drivers/hwmon/lm77.c @@ -87,15 +87,15 @@ static struct i2c_driver lm77_driver = { /* In the temperature registers, the low 3 bits are not part of the temperature values; they are the status bits. */ -static inline u16 LM77_TEMP_TO_REG(int temp) +static inline s16 LM77_TEMP_TO_REG(int temp) { int ntemp = SENSORS_LIMIT(temp, LM77_TEMP_MIN, LM77_TEMP_MAX); - return (u16)((ntemp / 500) * 8); + return (ntemp / 500) * 8; } -static inline int LM77_TEMP_FROM_REG(u16 reg) +static inline int LM77_TEMP_FROM_REG(s16 reg) { - return ((int)reg / 8) * 500; + return (reg / 8) * 500; } /* sysfs stuff */ diff --git a/drivers/hwmon/w83792d.c b/drivers/hwmon/w83792d.c index b176bf0c4c7..a2f6bb67623 100644 --- a/drivers/hwmon/w83792d.c +++ b/drivers/hwmon/w83792d.c @@ -303,10 +303,6 @@ struct w83792d_data { static int w83792d_attach_adapter(struct i2c_adapter *adapter); static int w83792d_detect(struct i2c_adapter *adapter, int address, int kind); static int w83792d_detach_client(struct i2c_client *client); - -static int w83792d_read_value(struct i2c_client *client, u8 register); -static int w83792d_write_value(struct i2c_client *client, u8 register, - u8 value); static struct w83792d_data *w83792d_update_device(struct device *dev); #ifdef DEBUG @@ -329,6 +325,20 @@ static inline long in_count_from_reg(int nr, struct w83792d_data *data) return ((data->in[nr] << 2) | ((data->low_bits >> (2 * nr)) & 0x03)); } +/* The SMBus locks itself. The Winbond W83792D chip has a bank register, + but the driver only accesses registers in bank 0, so we don't have + to switch banks and lock access between switches. */ +static inline int w83792d_read_value(struct i2c_client *client, u8 reg) +{ + return i2c_smbus_read_byte_data(client, reg); +} + +static inline int +w83792d_write_value(struct i2c_client *client, u8 reg, u8 value) +{ + return i2c_smbus_write_byte_data(client, reg, value); +} + /* following are the sysfs callback functions */ static ssize_t show_in(struct device *dev, struct device_attribute *attr, char *buf) @@ -1386,19 +1396,6 @@ w83792d_detach_client(struct i2c_client *client) return 0; } -/* The SMBus locks itself. The Winbond W83792D chip has a bank register, - but the driver only accesses registers in bank 0, so we don't have - to switch banks and lock access between switches. */ -static int w83792d_read_value(struct i2c_client *client, u8 reg) -{ - return i2c_smbus_read_byte_data(client, reg); -} - -static int w83792d_write_value(struct i2c_client *client, u8 reg, u8 value) -{ - return i2c_smbus_write_byte_data(client, reg, value); -} - static void w83792d_init_client(struct i2c_client *client) { diff --git a/drivers/i2c/algos/i2c-algo-sibyte.c b/drivers/i2c/algos/i2c-algo-sibyte.c index 938848ae162..3df3f09995c 100644 --- a/drivers/i2c/algos/i2c-algo-sibyte.c +++ b/drivers/i2c/algos/i2c-algo-sibyte.c @@ -202,7 +202,7 @@ EXPORT_SYMBOL(i2c_sibyte_del_bus); #ifdef MODULE MODULE_AUTHOR("Kip Walker, Broadcom Corp."); MODULE_DESCRIPTION("SiByte I2C-Bus algorithm"); -MODULE_PARM(bit_scan, "i"); +module_param(bit_scan, int, 0); MODULE_PARM_DESC(bit_scan, "Scan for active chips on the bus"); MODULE_LICENSE("GPL"); diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index 08d5b8fed2d..ff92735c7c8 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -124,6 +124,7 @@ config I2C_I801 ICH6 ICH7 ESB2 + ICH8 This driver can also be built as a module. If so, the module will be called i2c-i801. diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c index 1c752ddc10e..8e0f3158215 100644 --- a/drivers/i2c/busses/i2c-i801.c +++ b/drivers/i2c/busses/i2c-i801.c @@ -32,6 +32,7 @@ ICH6 266A ICH7 27DA ESB2 269B + ICH8 283E This driver supports several versions of Intel's I/O Controller Hubs (ICH). For SMBus support, they are similar to the PIIX4 and are part of Intel's '810' and other chipsets. @@ -527,6 +528,7 @@ static struct pci_device_id i801_ids[] = { { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_16) }, { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_17) }, { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_17) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_5) }, { 0, } }; diff --git a/drivers/i2c/busses/i2c-parport-light.c b/drivers/i2c/busses/i2c-parport-light.c index 3e5eba9fcac..c63025a4c86 100644 --- a/drivers/i2c/busses/i2c-parport-light.c +++ b/drivers/i2c/busses/i2c-parport-light.c @@ -121,14 +121,11 @@ static struct i2c_adapter parport_adapter = { static int __init i2c_parport_init(void) { - int type_count; - - type_count = sizeof(adapter_parm)/sizeof(struct adapter_parm); - if (type < 0 || type >= type_count) { + if (type < 0 || type >= ARRAY_SIZE(adapter_parm)) { printk(KERN_WARNING "i2c-parport: invalid type (%d)\n", type); type = 0; } - + if (base == 0) { printk(KERN_INFO "i2c-parport: using default base 0x%x\n", DEFAULT_BASE); base = DEFAULT_BASE; @@ -152,7 +149,7 @@ static int __init i2c_parport_init(void) release_region(base, 3); return -ENODEV; } - + return 0; } diff --git a/drivers/i2c/busses/i2c-parport.c b/drivers/i2c/busses/i2c-parport.c index 2854d858fc9..7e2e8cd1c14 100644 --- a/drivers/i2c/busses/i2c-parport.c +++ b/drivers/i2c/busses/i2c-parport.c @@ -241,14 +241,11 @@ static struct parport_driver i2c_parport_driver = { static int __init i2c_parport_init(void) { - int type_count; - - type_count = sizeof(adapter_parm)/sizeof(struct adapter_parm); - if (type < 0 || type >= type_count) { + if (type < 0 || type >= ARRAY_SIZE(adapter_parm)) { printk(KERN_WARNING "i2c-parport: invalid type (%d)\n", type); type = 0; } - + return parport_register_driver(&i2c_parport_driver); } diff --git a/drivers/i2c/busses/i2c-pxa.c b/drivers/i2c/busses/i2c-pxa.c index 86e2234faf8..7579f4b256a 100644 --- a/drivers/i2c/busses/i2c-pxa.c +++ b/drivers/i2c/busses/i2c-pxa.c @@ -861,7 +861,7 @@ static irqreturn_t i2c_pxa_handler(int this_irq, void *dev_id, struct pt_regs *r decode_ISR(isr); } - if (i2c->irqlogidx < sizeof(i2c->isrlog)/sizeof(u32)) + if (i2c->irqlogidx < ARRAY_SIZE(i2c->isrlog)) i2c->isrlog[i2c->irqlogidx++] = isr; show_state(i2c); diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c index 0ce58b50604..1a2c9ab5d9e 100644 --- a/drivers/i2c/i2c-core.c +++ b/drivers/i2c/i2c-core.c @@ -946,6 +946,20 @@ s32 i2c_smbus_read_i2c_block_data(struct i2c_client *client, u8 command, u8 *val } } +s32 i2c_smbus_write_i2c_block_data(struct i2c_client *client, u8 command, + u8 length, u8 *values) +{ + union i2c_smbus_data data; + + if (length > I2C_SMBUS_BLOCK_MAX) + length = I2C_SMBUS_BLOCK_MAX; + data.block[0] = length; + memcpy(data.block + 1, values, length); + return i2c_smbus_xfer(client->adapter, client->addr, client->flags, + I2C_SMBUS_WRITE, command, + I2C_SMBUS_I2C_BLOCK_DATA, &data); +} + /* Simulate a SMBus command using the i2c protocol No checking of parameters is done! */ static s32 i2c_smbus_xfer_emulated(struct i2c_adapter * adapter, u16 addr, @@ -1150,6 +1164,7 @@ EXPORT_SYMBOL(i2c_smbus_read_word_data); EXPORT_SYMBOL(i2c_smbus_write_word_data); EXPORT_SYMBOL(i2c_smbus_write_block_data); EXPORT_SYMBOL(i2c_smbus_read_i2c_block_data); +EXPORT_SYMBOL(i2c_smbus_write_i2c_block_data); MODULE_AUTHOR("Simon G. Vogl <simon@tk.uni-linz.ac.at>"); MODULE_DESCRIPTION("I2C-Bus main module"); diff --git a/drivers/ide/ide-disk.c b/drivers/ide/ide-disk.c index 6c60a9d2afd..09086b8b648 100644 --- a/drivers/ide/ide-disk.c +++ b/drivers/ide/ide-disk.c @@ -190,7 +190,8 @@ static ide_startstop_t __ide_do_rw_disk(ide_drive_t *drive, struct request *rq, if (lba48) { task_ioreg_t tasklets[10]; - pr_debug("%s: LBA=0x%012llx\n", drive->name, block); + pr_debug("%s: LBA=0x%012llx\n", drive->name, + (unsigned long long)block); tasklets[0] = 0; tasklets[1] = 0; @@ -317,7 +318,8 @@ static ide_startstop_t ide_do_rw_disk (ide_drive_t *drive, struct request *rq, s pr_debug("%s: %sing: block=%llu, sectors=%lu, buffer=0x%08lx\n", drive->name, rq_data_dir(rq) == READ ? "read" : "writ", - block, rq->nr_sectors, (unsigned long)rq->buffer); + (unsigned long long)block, rq->nr_sectors, + (unsigned long)rq->buffer); if (hwif->rw_disk) hwif->rw_disk(drive, rq); diff --git a/drivers/media/dvb/b2c2/Kconfig b/drivers/media/dvb/b2c2/Kconfig index 2583a865a58..2963605c0ec 100644 --- a/drivers/media/dvb/b2c2/Kconfig +++ b/drivers/media/dvb/b2c2/Kconfig @@ -4,7 +4,7 @@ config DVB_B2C2_FLEXCOP select DVB_STV0299 select DVB_MT352 select DVB_MT312 - select DVB_NXT2002 + select DVB_NXT200X select DVB_STV0297 select DVB_BCM3510 select DVB_LGDT330X diff --git a/drivers/media/dvb/b2c2/flexcop-common.h b/drivers/media/dvb/b2c2/flexcop-common.h index 344a3c89846..7d7e1613c5a 100644 --- a/drivers/media/dvb/b2c2/flexcop-common.h +++ b/drivers/media/dvb/b2c2/flexcop-common.h @@ -116,11 +116,9 @@ void flexcop_dma_free(struct flexcop_dma *dma); int flexcop_dma_control_timer_irq(struct flexcop_device *fc, flexcop_dma_index_t no, int onoff); int flexcop_dma_control_size_irq(struct flexcop_device *fc, flexcop_dma_index_t no, int onoff); -int flexcop_dma_control_packet_irq(struct flexcop_device *fc, flexcop_dma_index_t no, int onoff); int flexcop_dma_config(struct flexcop_device *fc, struct flexcop_dma *dma, flexcop_dma_index_t dma_idx); int flexcop_dma_xfer_control(struct flexcop_device *fc, flexcop_dma_index_t dma_idx, flexcop_dma_addr_index_t index, int onoff); int flexcop_dma_config_timer(struct flexcop_device *fc, flexcop_dma_index_t dma_idx, u8 cycles); -int flexcop_dma_config_packet_count(struct flexcop_device *fc, flexcop_dma_index_t dma_idx, u8 packets); /* from flexcop-eeprom.c */ /* the PCI part uses this call to get the MAC address, the USB part has its own */ diff --git a/drivers/media/dvb/b2c2/flexcop-dma.c b/drivers/media/dvb/b2c2/flexcop-dma.c index cf4ed1df608..6f592bc32d2 100644 --- a/drivers/media/dvb/b2c2/flexcop-dma.c +++ b/drivers/media/dvb/b2c2/flexcop-dma.c @@ -169,38 +169,3 @@ int flexcop_dma_config_timer(struct flexcop_device *fc, } EXPORT_SYMBOL(flexcop_dma_config_timer); -/* packet IRQ does not exist in FCII or FCIIb - according to data book and tests */ -int flexcop_dma_control_packet_irq(struct flexcop_device *fc, - flexcop_dma_index_t no, - int onoff) -{ - flexcop_ibi_value v = fc->read_ibi_reg(fc,ctrl_208); - - deb_rdump("reg: %03x: %x\n",ctrl_208,v.raw); - if (no & FC_DMA_1) - v.ctrl_208.DMA1_Size_IRQ_Enable_sig = onoff; - - if (no & FC_DMA_2) - v.ctrl_208.DMA2_Size_IRQ_Enable_sig = onoff; - - fc->write_ibi_reg(fc,ctrl_208,v); - deb_rdump("reg: %03x: %x\n",ctrl_208,v.raw); - - return 0; -} -EXPORT_SYMBOL(flexcop_dma_control_packet_irq); - -int flexcop_dma_config_packet_count(struct flexcop_device *fc, - flexcop_dma_index_t dma_idx, - u8 packets) -{ - flexcop_ibi_register r = (dma_idx & FC_DMA_1) ? dma1_004 : dma2_014; - flexcop_ibi_value v = fc->read_ibi_reg(fc,r); - - flexcop_dma_remap(fc,dma_idx,1); - - v.dma_0x4_remap.DMA_maxpackets = packets; - fc->write_ibi_reg(fc,r,v); - return 0; -} -EXPORT_SYMBOL(flexcop_dma_config_packet_count); diff --git a/drivers/media/dvb/b2c2/flexcop-fe-tuner.c b/drivers/media/dvb/b2c2/flexcop-fe-tuner.c index 0b940e152b7..390cc3a99ce 100644 --- a/drivers/media/dvb/b2c2/flexcop-fe-tuner.c +++ b/drivers/media/dvb/b2c2/flexcop-fe-tuner.c @@ -9,7 +9,7 @@ #include "stv0299.h" #include "mt352.h" -#include "nxt2002.h" +#include "nxt200x.h" #include "bcm3510.h" #include "stv0297.h" #include "mt312.h" @@ -343,9 +343,10 @@ static struct lgdt330x_config air2pc_atsc_hd5000_config = { .clock_polarity_flip = 1, }; -static struct nxt2002_config samsung_tbmv_config = { +static struct nxt200x_config samsung_tbmv_config = { .demod_address = 0x0a, - .request_firmware = flexcop_fe_request_firmware, + .pll_address = 0xc2, + .pll_desc = &dvb_pll_samsung_tbmv, }; static struct bcm3510_config air2pc_atsc_first_gen_config = { @@ -505,7 +506,7 @@ int flexcop_frontend_init(struct flexcop_device *fc) info("found the mt352 at i2c address: 0x%02x",samsung_tdtc9251dh0_config.demod_address); } else /* try the air atsc 2nd generation (nxt2002) */ - if ((fc->fe = nxt2002_attach(&samsung_tbmv_config, &fc->i2c_adap)) != NULL) { + if ((fc->fe = nxt200x_attach(&samsung_tbmv_config, &fc->i2c_adap)) != NULL) { fc->dev_type = FC_AIR_ATSC2; info("found the nxt2002 at i2c address: 0x%02x",samsung_tbmv_config.demod_address); } else diff --git a/drivers/media/dvb/b2c2/flexcop-misc.c b/drivers/media/dvb/b2c2/flexcop-misc.c index 62282d8dbfa..167583bf062 100644 --- a/drivers/media/dvb/b2c2/flexcop-misc.c +++ b/drivers/media/dvb/b2c2/flexcop-misc.c @@ -36,14 +36,14 @@ void flexcop_determine_revision(struct flexcop_device *fc) /* bus parts have to decide if hw pid filtering is used or not. */ } -const char *flexcop_revision_names[] = { +static const char *flexcop_revision_names[] = { "Unkown chip", "FlexCopII", "FlexCopIIb", "FlexCopIII", }; -const char *flexcop_device_names[] = { +static const char *flexcop_device_names[] = { "Unkown device", "Air2PC/AirStar 2 DVB-T", "Air2PC/AirStar 2 ATSC 1st generation", @@ -54,7 +54,7 @@ const char *flexcop_device_names[] = { "Air2PC/AirStar 2 ATSC 3rd generation (HD5000)", }; -const char *flexcop_bus_names[] = { +static const char *flexcop_bus_names[] = { "USB", "PCI", }; diff --git a/drivers/media/dvb/b2c2/flexcop-pci.c b/drivers/media/dvb/b2c2/flexcop-pci.c index 2f76eb3fea4..9bc40bdcc28 100644 --- a/drivers/media/dvb/b2c2/flexcop-pci.c +++ b/drivers/media/dvb/b2c2/flexcop-pci.c @@ -161,8 +161,10 @@ static irqreturn_t flexcop_pci_isr(int irq, void *dev_id, struct pt_regs *regs) fc->read_ibi_reg(fc,dma1_008).dma_0x8.dma_cur_addr << 2; u32 cur_pos = cur_addr - fc_pci->dma[0].dma_addr0; - deb_irq("%u irq: %08x cur_addr: %08x: cur_pos: %08x, last_cur_pos: %08x ", - jiffies_to_usecs(jiffies - fc_pci->last_irq),v.raw,cur_addr,cur_pos,fc_pci->last_dma1_cur_pos); + deb_irq("%u irq: %08x cur_addr: %llx: cur_pos: %08x, last_cur_pos: %08x ", + jiffies_to_usecs(jiffies - fc_pci->last_irq), + v.raw, (unsigned long long)cur_addr, cur_pos, + fc_pci->last_dma1_cur_pos); fc_pci->last_irq = jiffies; /* buffer end was reached, restarted from the beginning diff --git a/drivers/media/dvb/b2c2/flexcop-reg.h b/drivers/media/dvb/b2c2/flexcop-reg.h index 3153f9513c6..491f9bd6e19 100644 --- a/drivers/media/dvb/b2c2/flexcop-reg.h +++ b/drivers/media/dvb/b2c2/flexcop-reg.h @@ -16,8 +16,6 @@ typedef enum { FLEXCOP_III, } flexcop_revision_t; -extern const char *flexcop_revision_names[]; - typedef enum { FC_UNK = 0, FC_AIR_DVB, @@ -34,8 +32,6 @@ typedef enum { FC_PCI, } flexcop_bus_t; -extern const char *flexcop_device_names[]; - /* FlexCop IBI Registers */ #if defined(__LITTLE_ENDIAN) #include "flexcop_ibi_value_le.h" diff --git a/drivers/media/dvb/bt8xx/bt878.c b/drivers/media/dvb/bt8xx/bt878.c index a04bb61f21f..34c3189a1a3 100644 --- a/drivers/media/dvb/bt8xx/bt878.c +++ b/drivers/media/dvb/bt8xx/bt878.c @@ -381,6 +381,23 @@ bt878_device_control(struct bt878 *bt, unsigned int cmd, union dst_gpio_packet * EXPORT_SYMBOL(bt878_device_control); + +struct cards card_list[] __devinitdata = { + + { 0x01010071, BTTV_BOARD_NEBULA_DIGITV, "Nebula Electronics DigiTV" }, + { 0x07611461, BTTV_BOARD_AVDVBT_761, "AverMedia AverTV DVB-T 761" }, + { 0x001c11bd, BTTV_BOARD_PINNACLESAT, "Pinnacle PCTV Sat" }, + { 0x002611bd, BTTV_BOARD_TWINHAN_DST, "Pinnacle PCTV SAT CI" }, + { 0x00011822, BTTV_BOARD_TWINHAN_DST, "Twinhan VisionPlus DVB" }, + { 0xfc00270f, BTTV_BOARD_TWINHAN_DST, "ChainTech digitop DST-1000 DVB-S" }, + { 0x07711461, BTTV_BOARD_AVDVBT_771, "AVermedia AverTV DVB-T 771" }, + { 0xdb1018ac, BTTV_BOARD_DVICO_DVBT_LITE, "DViCO FusionHDTV DVB-T Lite" }, + { 0xd50018ac, BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE, "DViCO FusionHDTV 5 Lite" }, + { 0x20007063, BTTV_BOARD_PC_HDTV, "pcHDTV HD-2000 TV"}, + { 0, -1, NULL } +}; + + /***********************/ /* PCI device handling */ /***********************/ @@ -388,18 +405,41 @@ EXPORT_SYMBOL(bt878_device_control); static int __devinit bt878_probe(struct pci_dev *dev, const struct pci_device_id *pci_id) { - int result; + int result = 0, has_dvb = 0, i; unsigned char lat; struct bt878 *bt; #if defined(__powerpc__) unsigned int cmd; #endif + unsigned int cardid; + unsigned short id; + struct cards *dvb_cards; printk(KERN_INFO "bt878: Bt878 AUDIO function found (%d).\n", bt878_num); if (pci_enable_device(dev)) return -EIO; + pci_read_config_word(dev, PCI_SUBSYSTEM_ID, &id); + cardid = id << 16; + pci_read_config_word(dev, PCI_SUBSYSTEM_VENDOR_ID, &id); + cardid |= id; + + for (i = 0, dvb_cards = card_list; i < ARRAY_SIZE(card_list); i++, dvb_cards++) { + if (cardid == dvb_cards->pci_id) { + printk("%s: card id=[0x%x],[ %s ] has DVB functions.\n", + __func__, cardid, dvb_cards->name); + has_dvb = 1; + } + } + + if (!has_dvb) { + printk("%s: card id=[0x%x], Unknown card.\nExiting..\n", __func__, cardid); + result = -EINVAL; + + goto fail0; + } + bt = &bt878[bt878_num]; bt->dev = dev; bt->nr = bt878_num; @@ -416,6 +456,8 @@ static int __devinit bt878_probe(struct pci_dev *dev, pci_read_config_byte(dev, PCI_CLASS_REVISION, &bt->revision); pci_read_config_byte(dev, PCI_LATENCY_TIMER, &lat); + + printk(KERN_INFO "bt878(%d): Bt%x (rev %d) at %02x:%02x.%x, ", bt878_num, bt->id, bt->revision, dev->bus->number, PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn)); diff --git a/drivers/media/dvb/bt8xx/bt878.h b/drivers/media/dvb/bt8xx/bt878.h index a73baf00ca3..9faf93770d0 100644 --- a/drivers/media/dvb/bt8xx/bt878.h +++ b/drivers/media/dvb/bt8xx/bt878.h @@ -88,6 +88,23 @@ #define BT878_RISC_SYNC_MASK (1 << 15) + +#define BTTV_BOARD_UNKNOWN 0x00 +#define BTTV_BOARD_PINNACLESAT 0x5e +#define BTTV_BOARD_NEBULA_DIGITV 0x68 +#define BTTV_BOARD_PC_HDTV 0x70 +#define BTTV_BOARD_TWINHAN_DST 0x71 +#define BTTV_BOARD_AVDVBT_771 0x7b +#define BTTV_BOARD_AVDVBT_761 0x7c +#define BTTV_BOARD_DVICO_DVBT_LITE 0x80 +#define BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE 0x87 + +struct cards { + __u32 pci_id; + __u16 card_id; + char *name; +}; + extern int bt878_num; struct bt878 { diff --git a/drivers/media/dvb/dvb-usb/Kconfig b/drivers/media/dvb/dvb-usb/Kconfig index 90a69d343b7..d3df12039b0 100644 --- a/drivers/media/dvb/dvb-usb/Kconfig +++ b/drivers/media/dvb/dvb-usb/Kconfig @@ -83,12 +83,18 @@ config DVB_USB_UMT_010 Say Y here to support the HanfTek UMT-010 USB2.0 stick-sized DVB-T receiver. config DVB_USB_CXUSB - tristate "Medion MD95700 hybrid USB2.0 (Conexant) support" + tristate "Conexant USB2.0 hybrid reference design support" depends on DVB_USB select DVB_CX22702 + select DVB_LGDT330X + select DVB_MT352 help - Say Y here to support the Medion MD95700 hybrid USB2.0 device. Currently - only the DVB-T part is supported. + Say Y here to support the Conexant USB2.0 hybrid reference design. + Currently, only DVB and ATSC modes are supported, analog mode + shall be added in the future. Devices that require this module: + + Medion MD95700 hybrid USB2.0 device. + DViCO FusionHDTV (Bluebird) USB2.0 devices config DVB_USB_DIGITV tristate "Nebula Electronics uDigiTV DVB-T USB2.0 support" diff --git a/drivers/media/dvb/dvb-usb/cxusb.c b/drivers/media/dvb/dvb-usb/cxusb.c index a7fb06f4cd3..f327fac1688 100644 --- a/drivers/media/dvb/dvb-usb/cxusb.c +++ b/drivers/media/dvb/dvb-usb/cxusb.c @@ -184,7 +184,7 @@ static int cxusb_rc_query(struct dvb_usb_device *d, u32 *event, int *state) return 0; } -struct dvb_usb_rc_key dvico_mce_rc_keys[] = { +static struct dvb_usb_rc_key dvico_mce_rc_keys[] = { { 0xfe, 0x02, KEY_TV }, { 0xfe, 0x0e, KEY_MP3 }, { 0xfe, 0x1a, KEY_DVD }, @@ -234,7 +234,7 @@ struct dvb_usb_rc_key dvico_mce_rc_keys[] = { static int cxusb_dee1601_demod_init(struct dvb_frontend* fe) { - static u8 clock_config [] = { CLOCK_CTL, 0x38, 0x38 }; + static u8 clock_config [] = { CLOCK_CTL, 0x38, 0x28 }; static u8 reset [] = { RESET, 0x80 }; static u8 adc_ctl_1_cfg [] = { ADC_CTL_1, 0x40 }; static u8 agc_cfg [] = { AGC_TARGET, 0x28, 0x20 }; @@ -255,7 +255,7 @@ static int cxusb_dee1601_demod_init(struct dvb_frontend* fe) static int cxusb_mt352_demod_init(struct dvb_frontend* fe) { /* used in both lgz201 and th7579 */ - static u8 clock_config [] = { CLOCK_CTL, 0x38, 0x39 }; + static u8 clock_config [] = { CLOCK_CTL, 0x38, 0x29 }; static u8 reset [] = { RESET, 0x80 }; static u8 adc_ctl_1_cfg [] = { ADC_CTL_1, 0x40 }; static u8 agc_cfg [] = { AGC_TARGET, 0x24, 0x20 }; @@ -273,7 +273,7 @@ static int cxusb_mt352_demod_init(struct dvb_frontend* fe) return 0; } -struct cx22702_config cxusb_cx22702_config = { +static struct cx22702_config cxusb_cx22702_config = { .demod_address = 0x63, .output_mode = CX22702_PARALLEL_OUTPUT, @@ -282,13 +282,13 @@ struct cx22702_config cxusb_cx22702_config = { .pll_set = dvb_usb_pll_set_i2c, }; -struct lgdt330x_config cxusb_lgdt330x_config = { +static struct lgdt330x_config cxusb_lgdt330x_config = { .demod_address = 0x0e, .demod_chip = LGDT3303, .pll_set = dvb_usb_pll_set_i2c, }; -struct mt352_config cxusb_dee1601_config = { +static struct mt352_config cxusb_dee1601_config = { .demod_address = 0x0f, .demod_init = cxusb_dee1601_demod_init, .pll_set = dvb_usb_pll_set, diff --git a/drivers/media/dvb/dvb-usb/digitv.c b/drivers/media/dvb/dvb-usb/digitv.c index e6c55c9c941..caa1346e306 100644 --- a/drivers/media/dvb/dvb-usb/digitv.c +++ b/drivers/media/dvb/dvb-usb/digitv.c @@ -175,11 +175,13 @@ static int digitv_probe(struct usb_interface *intf, if ((ret = dvb_usb_device_init(intf,&digitv_properties,THIS_MODULE,&d)) == 0) { u8 b[4] = { 0 }; - b[0] = 1; - digitv_ctrl_msg(d,USB_WRITE_REMOTE_TYPE,0,b,4,NULL,0); + if (d != NULL) { /* do that only when the firmware is loaded */ + b[0] = 1; + digitv_ctrl_msg(d,USB_WRITE_REMOTE_TYPE,0,b,4,NULL,0); - b[0] = 0; - digitv_ctrl_msg(d,USB_WRITE_REMOTE,0,b,4,NULL,0); + b[0] = 0; + digitv_ctrl_msg(d,USB_WRITE_REMOTE,0,b,4,NULL,0); + } } return ret; } @@ -194,7 +196,7 @@ static struct dvb_usb_properties digitv_properties = { .caps = DVB_USB_IS_AN_I2C_ADAPTER, .usb_ctrl = CYPRESS_FX2, - .firmware = "dvb-usb-digitv-01.fw", + .firmware = "dvb-usb-digitv-02.fw", .size_of_priv = 0, @@ -229,6 +231,7 @@ static struct dvb_usb_properties digitv_properties = { { &digitv_table[0], NULL }, { NULL }, }, + { NULL }, } }; diff --git a/drivers/media/dvb/dvb-usb/dvb-usb-firmware.c b/drivers/media/dvb/dvb-usb/dvb-usb-firmware.c index 8535895819f..9222b0a81f7 100644 --- a/drivers/media/dvb/dvb-usb/dvb-usb-firmware.c +++ b/drivers/media/dvb/dvb-usb/dvb-usb-firmware.c @@ -24,6 +24,9 @@ static struct usb_cypress_controller cypress[] = { { .id = CYPRESS_FX2, .name = "Cypress FX2", .cpu_cs_register = 0xe600 }, }; +static int dvb_usb_get_hexline(const struct firmware *fw, struct hexline *hx, + int *pos); + /* * load a firmware packet to the device */ @@ -112,7 +115,8 @@ int dvb_usb_download_firmware(struct usb_device *udev, struct dvb_usb_properties return ret; } -int dvb_usb_get_hexline(const struct firmware *fw, struct hexline *hx, int *pos) +static int dvb_usb_get_hexline(const struct firmware *fw, struct hexline *hx, + int *pos) { u8 *b = (u8 *) &fw->data[*pos]; int data_offs = 4; @@ -142,5 +146,3 @@ int dvb_usb_get_hexline(const struct firmware *fw, struct hexline *hx, int *pos) return *pos; } -EXPORT_SYMBOL(dvb_usb_get_hexline); - diff --git a/drivers/media/dvb/dvb-usb/dvb-usb.h b/drivers/media/dvb/dvb-usb/dvb-usb.h index dd568396e59..5e5d21ad93c 100644 --- a/drivers/media/dvb/dvb-usb/dvb-usb.h +++ b/drivers/media/dvb/dvb-usb/dvb-usb.h @@ -341,7 +341,6 @@ struct hexline { u8 data[255]; u8 chk; }; -extern int dvb_usb_get_hexline(const struct firmware *, struct hexline *, int *); extern int usb_cypress_load_firmware(struct usb_device *udev, const struct firmware *fw, int type); #endif diff --git a/drivers/media/dvb/dvb-usb/vp702x.c b/drivers/media/dvb/dvb-usb/vp702x.c index afa00fdb5ec..4a95eca81c5 100644 --- a/drivers/media/dvb/dvb-usb/vp702x.c +++ b/drivers/media/dvb/dvb-usb/vp702x.c @@ -53,7 +53,8 @@ int vp702x_usb_in_op(struct dvb_usb_device *d, u8 req, u16 value, u16 index, u8 return ret; } -int vp702x_usb_out_op(struct dvb_usb_device *d, u8 req, u16 value, u16 index, u8 *b, int blen) +static int vp702x_usb_out_op(struct dvb_usb_device *d, u8 req, u16 value, + u16 index, u8 *b, int blen) { deb_xfer("out: req. %x, val: %x, ind: %x, buffer: ",req,value,index); debug_dump(b,blen,deb_xfer); @@ -88,7 +89,8 @@ unlock: return ret; } -int vp702x_usb_inout_cmd(struct dvb_usb_device *d, u8 cmd, u8 *o, int olen, u8 *i, int ilen, int msec) +static int vp702x_usb_inout_cmd(struct dvb_usb_device *d, u8 cmd, u8 *o, + int olen, u8 *i, int ilen, int msec) { u8 bout[olen+2]; u8 bin[ilen+1]; diff --git a/drivers/media/dvb/dvb-usb/vp702x.h b/drivers/media/dvb/dvb-usb/vp702x.h index a808d48e7bf..c2f97f96c21 100644 --- a/drivers/media/dvb/dvb-usb/vp702x.h +++ b/drivers/media/dvb/dvb-usb/vp702x.h @@ -101,8 +101,6 @@ extern int dvb_usb_vp702x_debug; extern struct dvb_frontend * vp702x_fe_attach(struct dvb_usb_device *d); extern int vp702x_usb_inout_op(struct dvb_usb_device *d, u8 *o, int olen, u8 *i, int ilen, int msec); -extern int vp702x_usb_inout_cmd(struct dvb_usb_device *d, u8 cmd, u8 *o, int olen, u8 *i, int ilen, int msec); extern int vp702x_usb_in_op(struct dvb_usb_device *d, u8 req, u16 value, u16 index, u8 *b, int blen); -extern int vp702x_usb_out_op(struct dvb_usb_device *d, u8 req, u16 value, u16 index, u8 *b, int blen); #endif diff --git a/drivers/media/dvb/dvb-usb/vp7045-fe.c b/drivers/media/dvb/dvb-usb/vp7045-fe.c index 5242cca5db4..9999336aeeb 100644 --- a/drivers/media/dvb/dvb-usb/vp7045-fe.c +++ b/drivers/media/dvb/dvb-usb/vp7045-fe.c @@ -23,10 +23,11 @@ struct vp7045_fe_state { struct dvb_frontend fe; + struct dvb_frontend_ops ops; + struct dvb_usb_device *d; }; - static int vp7045_fe_read_status(struct dvb_frontend* fe, fe_status_t *status) { struct vp7045_fe_state *state = fe->demodulator_priv; @@ -150,7 +151,8 @@ struct dvb_frontend * vp7045_fe_attach(struct dvb_usb_device *d) goto error; s->d = d; - s->fe.ops = &vp7045_fe_ops; + memcpy(&s->ops, &vp7045_fe_ops, sizeof(struct dvb_frontend_ops)); + s->fe.ops = &s->ops; s->fe.demodulator_priv = s; goto success; diff --git a/drivers/media/dvb/frontends/Kconfig b/drivers/media/dvb/frontends/Kconfig index db3a8b40031..76b6a2aef32 100644 --- a/drivers/media/dvb/frontends/Kconfig +++ b/drivers/media/dvb/frontends/Kconfig @@ -28,12 +28,6 @@ config DVB_TDA8083 help A DVB-S tuner module. Say Y when you want to support this frontend. -config DVB_TDA80XX - tristate "Philips TDA8044 or TDA8083 based" - depends on DVB_CORE - help - A DVB-S tuner module. Say Y when you want to support this frontend. - config DVB_MT312 tristate "Zarlink MT312 based" depends on DVB_CORE @@ -139,12 +133,6 @@ config DVB_DIB3000MC comment "DVB-C (cable) frontends" depends on DVB_CORE -config DVB_ATMEL_AT76C651 - tristate "Atmel AT76C651 based" - depends on DVB_CORE - help - A DVB-C tuner module. Say Y when you want to support this frontend. - config DVB_VES1820 tristate "VLSI VES1820 based" depends on DVB_CORE @@ -166,18 +154,6 @@ config DVB_STV0297 comment "ATSC (North American/Korean Terresterial DTV) frontends" depends on DVB_CORE -config DVB_NXT2002 - tristate "Nxt2002 based" - depends on DVB_CORE - select FW_LOADER - help - An ATSC 8VSB tuner module. Say Y when you want to support this frontend. - - This driver needs external firmware. Please use the command - "<kerneldir>/Documentation/dvb/get_dvb_firmware nxt2002" to - download/extract it, and then copy it to /usr/lib/hotplug/firmware - or /lib/firmware (depending on configuration of firmware hotplug). - config DVB_NXT200X tristate "Nextwave NXT2002/NXT2004 based" depends on DVB_CORE diff --git a/drivers/media/dvb/frontends/Makefile b/drivers/media/dvb/frontends/Makefile index 615ec830e1c..1af769cd90c 100644 --- a/drivers/media/dvb/frontends/Makefile +++ b/drivers/media/dvb/frontends/Makefile @@ -8,7 +8,6 @@ obj-$(CONFIG_DVB_CORE) += dvb-pll.o obj-$(CONFIG_DVB_STV0299) += stv0299.o obj-$(CONFIG_DVB_SP8870) += sp8870.o obj-$(CONFIG_DVB_CX22700) += cx22700.o -obj-$(CONFIG_DVB_ATMEL_AT76C651) += at76c651.o obj-$(CONFIG_DVB_CX24110) += cx24110.o obj-$(CONFIG_DVB_TDA8083) += tda8083.o obj-$(CONFIG_DVB_L64781) += l64781.o @@ -22,10 +21,8 @@ obj-$(CONFIG_DVB_SP887X) += sp887x.o obj-$(CONFIG_DVB_NXT6000) += nxt6000.o obj-$(CONFIG_DVB_MT352) += mt352.o obj-$(CONFIG_DVB_CX22702) += cx22702.o -obj-$(CONFIG_DVB_TDA80XX) += tda80xx.o obj-$(CONFIG_DVB_TDA10021) += tda10021.o obj-$(CONFIG_DVB_STV0297) += stv0297.o -obj-$(CONFIG_DVB_NXT2002) += nxt2002.o obj-$(CONFIG_DVB_NXT200X) += nxt200x.o obj-$(CONFIG_DVB_OR51211) += or51211.o obj-$(CONFIG_DVB_OR51132) += or51132.o diff --git a/drivers/media/dvb/frontends/at76c651.c b/drivers/media/dvb/frontends/at76c651.c deleted file mode 100644 index 8e0f4b3a141..00000000000 --- a/drivers/media/dvb/frontends/at76c651.c +++ /dev/null @@ -1,450 +0,0 @@ -/* - * at76c651.c - * - * Atmel DVB-C Frontend Driver (at76c651/tua6010xs) - * - * Copyright (C) 2001 fnbrd <fnbrd@gmx.de> - * & 2002-2004 Andreas Oberritter <obi@linuxtv.org> - * & 2003 Wolfram Joost <dbox2@frokaschwei.de> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - * - * AT76C651 - * http://www.nalanda.nitc.ac.in/industry/datasheets/atmel/acrobat/doc1293.pdf - * http://www.atmel.com/atmel/acrobat/doc1320.pdf - */ - -#include <linux/init.h> -#include <linux/module.h> -#include <linux/moduleparam.h> -#include <linux/kernel.h> -#include <linux/string.h> -#include <linux/slab.h> -#include <linux/bitops.h> -#include "dvb_frontend.h" -#include "at76c651.h" - - -struct at76c651_state { - - struct i2c_adapter* i2c; - - struct dvb_frontend_ops ops; - - const struct at76c651_config* config; - - struct dvb_frontend frontend; - - /* revision of the chip */ - u8 revision; - - /* last QAM value set */ - u8 qam; -}; - -static int debug; -#define dprintk(args...) \ - do { \ - if (debug) printk(KERN_DEBUG "at76c651: " args); \ - } while (0) - - -#if ! defined(__powerpc__) -static __inline__ int __ilog2(unsigned long x) -{ - int i; - - if (x == 0) - return -1; - - for (i = 0; x != 0; i++) - x >>= 1; - - return i - 1; -} -#endif - -static int at76c651_writereg(struct at76c651_state* state, u8 reg, u8 data) -{ - int ret; - u8 buf[] = { reg, data }; - struct i2c_msg msg = - { .addr = state->config->demod_address, .flags = 0, .buf = buf, .len = 2 }; - - ret = i2c_transfer(state->i2c, &msg, 1); - - if (ret != 1) - dprintk("%s: writereg error " - "(reg == 0x%02x, val == 0x%02x, ret == %i)\n", - __FUNCTION__, reg, data, ret); - - msleep(10); - - return (ret != 1) ? -EREMOTEIO : 0; -} - -static u8 at76c651_readreg(struct at76c651_state* state, u8 reg) -{ - int ret; - u8 val; - struct i2c_msg msg[] = { - { .addr = state->config->demod_address, .flags = 0, .buf = ®, .len = 1 }, - { .addr = state->config->demod_address, .flags = I2C_M_RD, .buf = &val, .len = 1 } - }; - - ret = i2c_transfer(state->i2c, msg, 2); - - if (ret != 2) - dprintk("%s: readreg error (ret == %i)\n", __FUNCTION__, ret); - - return val; -} - -static int at76c651_reset(struct at76c651_state* state) -{ - return at76c651_writereg(state, 0x07, 0x01); -} - -static void at76c651_disable_interrupts(struct at76c651_state* state) -{ - at76c651_writereg(state, 0x0b, 0x00); -} - -static int at76c651_set_auto_config(struct at76c651_state *state) -{ - /* - * Autoconfig - */ - - at76c651_writereg(state, 0x06, 0x01); - - /* - * Performance optimizations, should be done after autoconfig - */ - - at76c651_writereg(state, 0x10, 0x06); - at76c651_writereg(state, 0x11, ((state->qam == 5) || (state->qam == 7)) ? 0x12 : 0x10); - at76c651_writereg(state, 0x15, 0x28); - at76c651_writereg(state, 0x20, 0x09); - at76c651_writereg(state, 0x24, ((state->qam == 5) || (state->qam == 7)) ? 0xC0 : 0x90); - at76c651_writereg(state, 0x30, 0x90); - if (state->qam == 5) - at76c651_writereg(state, 0x35, 0x2A); - - /* - * Initialize A/D-converter - */ - - if (state->revision == 0x11) { - at76c651_writereg(state, 0x2E, 0x38); - at76c651_writereg(state, 0x2F, 0x13); - } - - at76c651_disable_interrupts(state); - - /* - * Restart operation - */ - - at76c651_reset(state); - - return 0; -} - -static void at76c651_set_bbfreq(struct at76c651_state* state) -{ - at76c651_writereg(state, 0x04, 0x3f); - at76c651_writereg(state, 0x05, 0xee); -} - -static int at76c651_set_symbol_rate(struct at76c651_state* state, u32 symbol_rate) -{ - u8 exponent; - u32 mantissa; - - if (symbol_rate > 9360000) - return -EINVAL; - - /* - * FREF = 57800 kHz - * exponent = 10 + floor (log2(symbol_rate / FREF)) - * mantissa = (symbol_rate / FREF) * (1 << (30 - exponent)) - */ - - exponent = __ilog2((symbol_rate << 4) / 903125); - mantissa = ((symbol_rate / 3125) * (1 << (24 - exponent))) / 289; - - at76c651_writereg(state, 0x00, mantissa >> 13); - at76c651_writereg(state, 0x01, mantissa >> 5); - at76c651_writereg(state, 0x02, (mantissa << 3) | exponent); - - return 0; -} - -static int at76c651_set_qam(struct at76c651_state *state, fe_modulation_t qam) -{ - switch (qam) { - case QPSK: - state->qam = 0x02; - break; - case QAM_16: - state->qam = 0x04; - break; - case QAM_32: - state->qam = 0x05; - break; - case QAM_64: - state->qam = 0x06; - break; - case QAM_128: - state->qam = 0x07; - break; - case QAM_256: - state->qam = 0x08; - break; -#if 0 - case QAM_512: - state->qam = 0x09; - break; - case QAM_1024: - state->qam = 0x0A; - break; -#endif - default: - return -EINVAL; - - } - - return at76c651_writereg(state, 0x03, state->qam); -} - -static int at76c651_set_inversion(struct at76c651_state* state, fe_spectral_inversion_t inversion) -{ - u8 feciqinv = at76c651_readreg(state, 0x60); - - switch (inversion) { - case INVERSION_OFF: - feciqinv |= 0x02; - feciqinv &= 0xFE; - break; - - case INVERSION_ON: - feciqinv |= 0x03; - break; - - case INVERSION_AUTO: - feciqinv &= 0xFC; - break; - - default: - return -EINVAL; - } - - return at76c651_writereg(state, 0x60, feciqinv); -} - -static int at76c651_set_parameters(struct dvb_frontend* fe, - struct dvb_frontend_parameters *p) -{ - int ret; - struct at76c651_state* state = fe->demodulator_priv; - - at76c651_writereg(state, 0x0c, 0xc3); - state->config->pll_set(fe, p); - at76c651_writereg(state, 0x0c, 0xc2); - - if ((ret = at76c651_set_symbol_rate(state, p->u.qam.symbol_rate))) - return ret; - - if ((ret = at76c651_set_inversion(state, p->inversion))) - return ret; - - return at76c651_set_auto_config(state); -} - -static int at76c651_set_defaults(struct dvb_frontend* fe) -{ - struct at76c651_state* state = fe->demodulator_priv; - - at76c651_set_symbol_rate(state, 6900000); - at76c651_set_qam(state, QAM_64); - at76c651_set_bbfreq(state); - at76c651_set_auto_config(state); - - if (state->config->pll_init) { - at76c651_writereg(state, 0x0c, 0xc3); - state->config->pll_init(fe); - at76c651_writereg(state, 0x0c, 0xc2); - } - - return 0; -} - -static int at76c651_read_status(struct dvb_frontend* fe, fe_status_t* status) -{ - struct at76c651_state* state = fe->demodulator_priv; - u8 sync; - - /* - * Bits: FEC, CAR, EQU, TIM, AGC2, AGC1, ADC, PLL (PLL=0) - */ - sync = at76c651_readreg(state, 0x80); - *status = 0; - - if (sync & (0x04 | 0x10)) /* AGC1 || TIM */ - *status |= FE_HAS_SIGNAL; - if (sync & 0x10) /* TIM */ - *status |= FE_HAS_CARRIER; - if (sync & 0x80) /* FEC */ - *status |= FE_HAS_VITERBI; - if (sync & 0x40) /* CAR */ - *status |= FE_HAS_SYNC; - if ((sync & 0xF0) == 0xF0) /* TIM && EQU && CAR && FEC */ - *status |= FE_HAS_LOCK; - - return 0; -} - -static int at76c651_read_ber(struct dvb_frontend* fe, u32* ber) -{ - struct at76c651_state* state = fe->demodulator_priv; - - *ber = (at76c651_readreg(state, 0x81) & 0x0F) << 16; - *ber |= at76c651_readreg(state, 0x82) << 8; - *ber |= at76c651_readreg(state, 0x83); - *ber *= 10; - - return 0; -} - -static int at76c651_read_signal_strength(struct dvb_frontend* fe, u16* strength) -{ - struct at76c651_state* state = fe->demodulator_priv; - - u8 gain = ~at76c651_readreg(state, 0x91); - *strength = (gain << 8) | gain; - - return 0; -} - -static int at76c651_read_snr(struct dvb_frontend* fe, u16* snr) -{ - struct at76c651_state* state = fe->demodulator_priv; - - *snr = 0xFFFF - - ((at76c651_readreg(state, 0x8F) << 8) | - at76c651_readreg(state, 0x90)); - - return 0; -} - -static int at76c651_read_ucblocks(struct dvb_frontend* fe, u32* ucblocks) -{ - struct at76c651_state* state = fe->demodulator_priv; - - *ucblocks = at76c651_readreg(state, 0x82); - - return 0; -} - -static int at76c651_get_tune_settings(struct dvb_frontend* fe, struct dvb_frontend_tune_settings *fesettings) -{ - fesettings->min_delay_ms = 50; - fesettings->step_size = 0; - fesettings->max_drift = 0; - return 0; -} - -static void at76c651_release(struct dvb_frontend* fe) -{ - struct at76c651_state* state = fe->demodulator_priv; - kfree(state); -} - -static struct dvb_frontend_ops at76c651_ops; - -struct dvb_frontend* at76c651_attach(const struct at76c651_config* config, - struct i2c_adapter* i2c) -{ - struct at76c651_state* state = NULL; - - /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct at76c651_state), GFP_KERNEL); - if (state == NULL) goto error; - - /* setup the state */ - state->config = config; - state->qam = 0; - - /* check if the demod is there */ - if (at76c651_readreg(state, 0x0e) != 0x65) goto error; - - /* finalise state setup */ - state->i2c = i2c; - state->revision = at76c651_readreg(state, 0x0f) & 0xfe; - memcpy(&state->ops, &at76c651_ops, sizeof(struct dvb_frontend_ops)); - - /* create dvb_frontend */ - state->frontend.ops = &state->ops; - state->frontend.demodulator_priv = state; - return &state->frontend; - -error: - kfree(state); - return NULL; -} - -static struct dvb_frontend_ops at76c651_ops = { - - .info = { - .name = "Atmel AT76C651B DVB-C", - .type = FE_QAM, - .frequency_min = 48250000, - .frequency_max = 863250000, - .frequency_stepsize = 62500, - /*.frequency_tolerance = */ /* FIXME: 12% of SR */ - .symbol_rate_min = 0, /* FIXME */ - .symbol_rate_max = 9360000, /* FIXME */ - .symbol_rate_tolerance = 4000, - .caps = FE_CAN_INVERSION_AUTO | - FE_CAN_FEC_1_2 | FE_CAN_FEC_2_3 | FE_CAN_FEC_3_4 | - FE_CAN_FEC_4_5 | FE_CAN_FEC_5_6 | FE_CAN_FEC_6_7 | - FE_CAN_FEC_7_8 | FE_CAN_FEC_8_9 | FE_CAN_FEC_AUTO | - FE_CAN_QAM_16 | FE_CAN_QAM_32 | FE_CAN_QAM_64 | FE_CAN_QAM_128 | - FE_CAN_MUTE_TS | FE_CAN_QAM_256 | FE_CAN_RECOVER - }, - - .release = at76c651_release, - - .init = at76c651_set_defaults, - - .set_frontend = at76c651_set_parameters, - .get_tune_settings = at76c651_get_tune_settings, - - .read_status = at76c651_read_status, - .read_ber = at76c651_read_ber, - .read_signal_strength = at76c651_read_signal_strength, - .read_snr = at76c651_read_snr, - .read_ucblocks = at76c651_read_ucblocks, -}; - -module_param(debug, int, 0644); -MODULE_PARM_DESC(debug, "Turn on/off frontend debugging (default:off)."); - -MODULE_DESCRIPTION("Atmel AT76C651 DVB-C Demodulator Driver"); -MODULE_AUTHOR("Andreas Oberritter <obi@linuxtv.org>"); -MODULE_LICENSE("GPL"); - -EXPORT_SYMBOL(at76c651_attach); diff --git a/drivers/media/dvb/frontends/at76c651.h b/drivers/media/dvb/frontends/at76c651.h deleted file mode 100644 index 34054df9360..00000000000 --- a/drivers/media/dvb/frontends/at76c651.h +++ /dev/null @@ -1,47 +0,0 @@ -/* - * at76c651.c - * - * Atmel DVB-C Frontend Driver (at76c651) - * - * Copyright (C) 2001 fnbrd <fnbrd@gmx.de> - * & 2002-2004 Andreas Oberritter <obi@linuxtv.org> - * & 2003 Wolfram Joost <dbox2@frokaschwei.de> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - * - * AT76C651 - * http://www.nalanda.nitc.ac.in/industry/datasheets/atmel/acrobat/doc1293.pdf - * http://www.atmel.com/atmel/acrobat/doc1320.pdf - */ - -#ifndef AT76C651_H -#define AT76C651_H - -#include <linux/dvb/frontend.h> - -struct at76c651_config -{ - /* the demodulator's i2c address */ - u8 demod_address; - - /* PLL maintenance */ - int (*pll_init)(struct dvb_frontend* fe); - int (*pll_set)(struct dvb_frontend* fe, struct dvb_frontend_parameters* params); -}; - -extern struct dvb_frontend* at76c651_attach(const struct at76c651_config* config, - struct i2c_adapter* i2c); - -#endif // AT76C651_H diff --git a/drivers/media/dvb/frontends/dvb-pll.c b/drivers/media/dvb/frontends/dvb-pll.c index 1b9934ea5b0..4dcb6050d4f 100644 --- a/drivers/media/dvb/frontends/dvb-pll.c +++ b/drivers/media/dvb/frontends/dvb-pll.c @@ -326,11 +326,11 @@ struct dvb_pll_desc dvb_pll_tuv1236d = { }; EXPORT_SYMBOL(dvb_pll_tuv1236d); -/* Samsung TBMV30111IN +/* Samsung TBMV30111IN / TBMV30712IN1 * used in Air2PC ATSC - 2nd generation (nxt2002) */ -struct dvb_pll_desc dvb_pll_tbmv30111in = { - .name = "Samsung TBMV30111IN", +struct dvb_pll_desc dvb_pll_samsung_tbmv = { + .name = "Samsung TBMV30111IN / TBMV30712IN1", .min = 54000000, .max = 860000000, .count = 6, @@ -343,7 +343,7 @@ struct dvb_pll_desc dvb_pll_tbmv30111in = { { 999999999, 44000000, 166666, 0xfc, 0x02 }, } }; -EXPORT_SYMBOL(dvb_pll_tbmv30111in); +EXPORT_SYMBOL(dvb_pll_samsung_tbmv); /* * Philips SD1878 Tuner. diff --git a/drivers/media/dvb/frontends/dvb-pll.h b/drivers/media/dvb/frontends/dvb-pll.h index f682c09189b..bb8d4b4eb18 100644 --- a/drivers/media/dvb/frontends/dvb-pll.h +++ b/drivers/media/dvb/frontends/dvb-pll.h @@ -38,7 +38,7 @@ extern struct dvb_pll_desc dvb_pll_tded4; extern struct dvb_pll_desc dvb_pll_tuv1236d; extern struct dvb_pll_desc dvb_pll_tdhu2; -extern struct dvb_pll_desc dvb_pll_tbmv30111in; +extern struct dvb_pll_desc dvb_pll_samsung_tbmv; extern struct dvb_pll_desc dvb_pll_philips_sd1878_tda8261; int dvb_pll_configure(struct dvb_pll_desc *desc, u8 *buf, diff --git a/drivers/media/dvb/frontends/nxt2002.c b/drivers/media/dvb/frontends/nxt2002.c deleted file mode 100644 index 4f263e65ba1..00000000000 --- a/drivers/media/dvb/frontends/nxt2002.c +++ /dev/null @@ -1,706 +0,0 @@ -/* - Support for B2C2/BBTI Technisat Air2PC - ATSC - - Copyright (C) 2004 Taylor Jacob <rtjacob@earthlink.net> - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - -*/ - -/* - * This driver needs external firmware. Please use the command - * "<kerneldir>/Documentation/dvb/get_dvb_firmware nxt2002" to - * download/extract it, and then copy it to /usr/lib/hotplug/firmware - * or /lib/firmware (depending on configuration of firmware hotplug). - */ -#define NXT2002_DEFAULT_FIRMWARE "dvb-fe-nxt2002.fw" -#define CRC_CCIT_MASK 0x1021 - -#include <linux/init.h> -#include <linux/module.h> -#include <linux/moduleparam.h> -#include <linux/device.h> -#include <linux/firmware.h> -#include <linux/string.h> -#include <linux/slab.h> - -#include "dvb_frontend.h" -#include "nxt2002.h" - -struct nxt2002_state { - - struct i2c_adapter* i2c; - struct dvb_frontend_ops ops; - const struct nxt2002_config* config; - struct dvb_frontend frontend; - - /* demodulator private data */ - u8 initialised:1; -}; - -static int debug; -#define dprintk(args...) \ - do { \ - if (debug) printk(KERN_DEBUG "nxt2002: " args); \ - } while (0) - -static int i2c_writebytes (struct nxt2002_state* state, u8 reg, u8 *buf, u8 len) -{ - /* probbably a much better way or doing this */ - u8 buf2 [256],x; - int err; - struct i2c_msg msg = { .addr = state->config->demod_address, .flags = 0, .buf = buf2, .len = len + 1 }; - - buf2[0] = reg; - for (x = 0 ; x < len ; x++) - buf2[x+1] = buf[x]; - - if ((err = i2c_transfer (state->i2c, &msg, 1)) != 1) { - printk ("%s: i2c write error (addr %02x, err == %i)\n", - __FUNCTION__, state->config->demod_address, err); - return -EREMOTEIO; - } - - return 0; -} - -static u8 i2c_readbytes (struct nxt2002_state* state, u8 reg, u8* buf, u8 len) -{ - u8 reg2 [] = { reg }; - - struct i2c_msg msg [] = { { .addr = state->config->demod_address, .flags = 0, .buf = reg2, .len = 1 }, - { .addr = state->config->demod_address, .flags = I2C_M_RD, .buf = buf, .len = len } }; - - int err; - - if ((err = i2c_transfer (state->i2c, msg, 2)) != 2) { - printk ("%s: i2c read error (addr %02x, err == %i)\n", - __FUNCTION__, state->config->demod_address, err); - return -EREMOTEIO; - } - - return 0; -} - -static u16 nxt2002_crc(u16 crc, u8 c) -{ - - u8 i; - u16 input = (u16) c & 0xFF; - - input<<=8; - for(i=0 ;i<8 ;i++) { - if((crc ^ input) & 0x8000) - crc=(crc<<1)^CRC_CCIT_MASK; - else - crc<<=1; - input<<=1; - } - return crc; -} - -static int nxt2002_writereg_multibyte (struct nxt2002_state* state, u8 reg, u8* data, u8 len) -{ - u8 buf; - dprintk("%s\n", __FUNCTION__); - - /* set multi register length */ - i2c_writebytes(state,0x34,&len,1); - - /* set mutli register register */ - i2c_writebytes(state,0x35,®,1); - - /* send the actual data */ - i2c_writebytes(state,0x36,data,len); - - /* toggle the multireg write bit*/ - buf = 0x02; - i2c_writebytes(state,0x21,&buf,1); - - i2c_readbytes(state,0x21,&buf,1); - - if ((buf & 0x02) == 0) - return 0; - - dprintk("Error writing multireg register %02X\n",reg); - - return 0; -} - -static int nxt2002_readreg_multibyte (struct nxt2002_state* state, u8 reg, u8* data, u8 len) -{ - u8 len2; - dprintk("%s\n", __FUNCTION__); - - /* set multi register length */ - len2 = len & 0x80; - i2c_writebytes(state,0x34,&len2,1); - - /* set mutli register register */ - i2c_writebytes(state,0x35,®,1); - - /* send the actual data */ - i2c_readbytes(state,reg,data,len); - - return 0; -} - -static void nxt2002_microcontroller_stop (struct nxt2002_state* state) -{ - u8 buf[2],counter = 0; - dprintk("%s\n", __FUNCTION__); - - buf[0] = 0x80; - i2c_writebytes(state,0x22,buf,1); - - while (counter < 20) { - i2c_readbytes(state,0x31,buf,1); - if (buf[0] & 0x40) - return; - msleep(10); - counter++; - } - - dprintk("Timeout waiting for micro to stop.. This is ok after firmware upload\n"); - return; -} - -static void nxt2002_microcontroller_start (struct nxt2002_state* state) -{ - u8 buf; - dprintk("%s\n", __FUNCTION__); - - buf = 0x00; - i2c_writebytes(state,0x22,&buf,1); -} - -static int nxt2002_writetuner (struct nxt2002_state* state, u8* data) -{ - u8 buf,count = 0; - - dprintk("Tuner Bytes: %02X %02X %02X %02X\n",data[0],data[1],data[2],data[3]); - - dprintk("%s\n", __FUNCTION__); - /* stop the micro first */ - nxt2002_microcontroller_stop(state); - - /* set the i2c transfer speed to the tuner */ - buf = 0x03; - i2c_writebytes(state,0x20,&buf,1); - - /* setup to transfer 4 bytes via i2c */ - buf = 0x04; - i2c_writebytes(state,0x34,&buf,1); - - /* write actual tuner bytes */ - i2c_writebytes(state,0x36,data,4); - - /* set tuner i2c address */ - buf = 0xC2; - i2c_writebytes(state,0x35,&buf,1); - - /* write UC Opmode to begin transfer */ - buf = 0x80; - i2c_writebytes(state,0x21,&buf,1); - - while (count < 20) { - i2c_readbytes(state,0x21,&buf,1); - if ((buf & 0x80)== 0x00) - return 0; - msleep(100); - count++; - } - - printk("nxt2002: timeout error writing tuner\n"); - return 0; -} - -static void nxt2002_agc_reset(struct nxt2002_state* state) -{ - u8 buf; - dprintk("%s\n", __FUNCTION__); - - buf = 0x08; - i2c_writebytes(state,0x08,&buf,1); - - buf = 0x00; - i2c_writebytes(state,0x08,&buf,1); - - return; -} - -static int nxt2002_load_firmware (struct dvb_frontend* fe, const struct firmware *fw) -{ - - struct nxt2002_state* state = fe->demodulator_priv; - u8 buf[256],written = 0,chunkpos = 0; - u16 rambase,position,crc = 0; - - dprintk("%s\n", __FUNCTION__); - dprintk("Firmware is %zu bytes\n",fw->size); - - /* Get the RAM base for this nxt2002 */ - i2c_readbytes(state,0x10,buf,1); - - if (buf[0] & 0x10) - rambase = 0x1000; - else - rambase = 0x0000; - - dprintk("rambase on this nxt2002 is %04X\n",rambase); - - /* Hold the micro in reset while loading firmware */ - buf[0] = 0x80; - i2c_writebytes(state,0x2B,buf,1); - - for (position = 0; position < fw->size ; position++) { - if (written == 0) { - crc = 0; - chunkpos = 0x28; - buf[0] = ((rambase + position) >> 8); - buf[1] = (rambase + position) & 0xFF; - buf[2] = 0x81; - /* write starting address */ - i2c_writebytes(state,0x29,buf,3); - } - written++; - chunkpos++; - - if ((written % 4) == 0) - i2c_writebytes(state,chunkpos,&fw->data[position-3],4); - - crc = nxt2002_crc(crc,fw->data[position]); - - if ((written == 255) || (position+1 == fw->size)) { - /* write remaining bytes of firmware */ - i2c_writebytes(state, chunkpos+4-(written %4), - &fw->data[position-(written %4) + 1], - written %4); - buf[0] = crc << 8; - buf[1] = crc & 0xFF; - - /* write crc */ - i2c_writebytes(state,0x2C,buf,2); - - /* do a read to stop things */ - i2c_readbytes(state,0x2A,buf,1); - - /* set transfer mode to complete */ - buf[0] = 0x80; - i2c_writebytes(state,0x2B,buf,1); - - written = 0; - } - } - - printk ("done.\n"); - return 0; -}; - -static int nxt2002_setup_frontend_parameters (struct dvb_frontend* fe, - struct dvb_frontend_parameters *p) -{ - struct nxt2002_state* state = fe->demodulator_priv; - u32 freq = 0; - u16 tunerfreq = 0; - u8 buf[4]; - - freq = 44000 + ( p->frequency / 1000 ); - - dprintk("freq = %d p->frequency = %d\n",freq,p->frequency); - - tunerfreq = freq * 24/4000; - - buf[0] = (tunerfreq >> 8) & 0x7F; - buf[1] = (tunerfreq & 0xFF); - - if (p->frequency <= 214000000) { - buf[2] = 0x84 + (0x06 << 3); - buf[3] = (p->frequency <= 172000000) ? 0x01 : 0x02; - } else if (p->frequency <= 721000000) { - buf[2] = 0x84 + (0x07 << 3); - buf[3] = (p->frequency <= 467000000) ? 0x02 : 0x08; - } else if (p->frequency <= 841000000) { - buf[2] = 0x84 + (0x0E << 3); - buf[3] = 0x08; - } else { - buf[2] = 0x84 + (0x0F << 3); - buf[3] = 0x02; - } - - /* write frequency information */ - nxt2002_writetuner(state,buf); - - /* reset the agc now that tuning has been completed */ - nxt2002_agc_reset(state); - - /* set target power level */ - switch (p->u.vsb.modulation) { - case QAM_64: - case QAM_256: - buf[0] = 0x74; - break; - case VSB_8: - buf[0] = 0x70; - break; - default: - return -EINVAL; - break; - } - i2c_writebytes(state,0x42,buf,1); - - /* configure sdm */ - buf[0] = 0x87; - i2c_writebytes(state,0x57,buf,1); - - /* write sdm1 input */ - buf[0] = 0x10; - buf[1] = 0x00; - nxt2002_writereg_multibyte(state,0x58,buf,2); - - /* write sdmx input */ - switch (p->u.vsb.modulation) { - case QAM_64: - buf[0] = 0x68; - break; - case QAM_256: - buf[0] = 0x64; - break; - case VSB_8: - buf[0] = 0x60; - break; - default: - return -EINVAL; - break; - } - buf[1] = 0x00; - nxt2002_writereg_multibyte(state,0x5C,buf,2); - - /* write adc power lpf fc */ - buf[0] = 0x05; - i2c_writebytes(state,0x43,buf,1); - - /* write adc power lpf fc */ - buf[0] = 0x05; - i2c_writebytes(state,0x43,buf,1); - - /* write accumulator2 input */ - buf[0] = 0x80; - buf[1] = 0x00; - nxt2002_writereg_multibyte(state,0x4B,buf,2); - - /* write kg1 */ - buf[0] = 0x00; - i2c_writebytes(state,0x4D,buf,1); - - /* write sdm12 lpf fc */ - buf[0] = 0x44; - i2c_writebytes(state,0x55,buf,1); - - /* write agc control reg */ - buf[0] = 0x04; - i2c_writebytes(state,0x41,buf,1); - - /* write agc ucgp0 */ - switch (p->u.vsb.modulation) { - case QAM_64: - buf[0] = 0x02; - break; - case QAM_256: - buf[0] = 0x03; - break; - case VSB_8: - buf[0] = 0x00; - break; - default: - return -EINVAL; - break; - } - i2c_writebytes(state,0x30,buf,1); - - /* write agc control reg */ - buf[0] = 0x00; - i2c_writebytes(state,0x41,buf,1); - - /* write accumulator2 input */ - buf[0] = 0x80; - buf[1] = 0x00; - nxt2002_writereg_multibyte(state,0x49,buf,2); - nxt2002_writereg_multibyte(state,0x4B,buf,2); - - /* write agc control reg */ - buf[0] = 0x04; - i2c_writebytes(state,0x41,buf,1); - - nxt2002_microcontroller_start(state); - - /* adjacent channel detection should be done here, but I don't - have any stations with this need so I cannot test it */ - - return 0; -} - -static int nxt2002_read_status(struct dvb_frontend* fe, fe_status_t* status) -{ - struct nxt2002_state* state = fe->demodulator_priv; - u8 lock; - i2c_readbytes(state,0x31,&lock,1); - - *status = 0; - if (lock & 0x20) { - *status |= FE_HAS_SIGNAL; - *status |= FE_HAS_CARRIER; - *status |= FE_HAS_VITERBI; - *status |= FE_HAS_SYNC; - *status |= FE_HAS_LOCK; - } - return 0; -} - -static int nxt2002_read_ber(struct dvb_frontend* fe, u32* ber) -{ - struct nxt2002_state* state = fe->demodulator_priv; - u8 b[3]; - - nxt2002_readreg_multibyte(state,0xE6,b,3); - - *ber = ((b[0] << 8) + b[1]) * 8; - - return 0; -} - -static int nxt2002_read_signal_strength(struct dvb_frontend* fe, u16* strength) -{ - struct nxt2002_state* state = fe->demodulator_priv; - u8 b[2]; - u16 temp = 0; - - /* setup to read cluster variance */ - b[0] = 0x00; - i2c_writebytes(state,0xA1,b,1); - - /* get multreg val */ - nxt2002_readreg_multibyte(state,0xA6,b,2); - - temp = (b[0] << 8) | b[1]; - *strength = ((0x7FFF - temp) & 0x0FFF) * 16; - - return 0; -} - -static int nxt2002_read_snr(struct dvb_frontend* fe, u16* snr) -{ - - struct nxt2002_state* state = fe->demodulator_priv; - u8 b[2]; - u16 temp = 0, temp2; - u32 snrdb = 0; - - /* setup to read cluster variance */ - b[0] = 0x00; - i2c_writebytes(state,0xA1,b,1); - - /* get multreg val from 0xA6 */ - nxt2002_readreg_multibyte(state,0xA6,b,2); - - temp = (b[0] << 8) | b[1]; - temp2 = 0x7FFF - temp; - - /* snr will be in db */ - if (temp2 > 0x7F00) - snrdb = 1000*24 + ( 1000*(30-24) * ( temp2 - 0x7F00 ) / ( 0x7FFF - 0x7F00 ) ); - else if (temp2 > 0x7EC0) - snrdb = 1000*18 + ( 1000*(24-18) * ( temp2 - 0x7EC0 ) / ( 0x7F00 - 0x7EC0 ) ); - else if (temp2 > 0x7C00) - snrdb = 1000*12 + ( 1000*(18-12) * ( temp2 - 0x7C00 ) / ( 0x7EC0 - 0x7C00 ) ); - else - snrdb = 1000*0 + ( 1000*(12-0) * ( temp2 - 0 ) / ( 0x7C00 - 0 ) ); - - /* the value reported back from the frontend will be FFFF=32db 0000=0db */ - - *snr = snrdb * (0xFFFF/32000); - - return 0; -} - -static int nxt2002_read_ucblocks(struct dvb_frontend* fe, u32* ucblocks) -{ - struct nxt2002_state* state = fe->demodulator_priv; - u8 b[3]; - - nxt2002_readreg_multibyte(state,0xE6,b,3); - *ucblocks = b[2]; - - return 0; -} - -static int nxt2002_sleep(struct dvb_frontend* fe) -{ - return 0; -} - -static int nxt2002_init(struct dvb_frontend* fe) -{ - struct nxt2002_state* state = fe->demodulator_priv; - const struct firmware *fw; - int ret; - u8 buf[2]; - - if (!state->initialised) { - /* request the firmware, this will block until someone uploads it */ - printk("nxt2002: Waiting for firmware upload (%s)...\n", NXT2002_DEFAULT_FIRMWARE); - ret = state->config->request_firmware(fe, &fw, NXT2002_DEFAULT_FIRMWARE); - printk("nxt2002: Waiting for firmware upload(2)...\n"); - if (ret) { - printk("nxt2002: no firmware upload (timeout or file not found?)\n"); - return ret; - } - - ret = nxt2002_load_firmware(fe, fw); - if (ret) { - printk("nxt2002: writing firmware to device failed\n"); - release_firmware(fw); - return ret; - } - printk("nxt2002: firmware upload complete\n"); - - /* Put the micro into reset */ - nxt2002_microcontroller_stop(state); - - /* ensure transfer is complete */ - buf[0]=0; - i2c_writebytes(state,0x2B,buf,1); - - /* Put the micro into reset for real this time */ - nxt2002_microcontroller_stop(state); - - /* soft reset everything (agc,frontend,eq,fec)*/ - buf[0] = 0x0F; - i2c_writebytes(state,0x08,buf,1); - buf[0] = 0x00; - i2c_writebytes(state,0x08,buf,1); - - /* write agc sdm configure */ - buf[0] = 0xF1; - i2c_writebytes(state,0x57,buf,1); - - /* write mod output format */ - buf[0] = 0x20; - i2c_writebytes(state,0x09,buf,1); - - /* write fec mpeg mode */ - buf[0] = 0x7E; - buf[1] = 0x00; - i2c_writebytes(state,0xE9,buf,2); - - /* write mux selection */ - buf[0] = 0x00; - i2c_writebytes(state,0xCC,buf,1); - - state->initialised = 1; - } - - return 0; -} - -static int nxt2002_get_tune_settings(struct dvb_frontend* fe, struct dvb_frontend_tune_settings* fesettings) -{ - fesettings->min_delay_ms = 500; - fesettings->step_size = 0; - fesettings->max_drift = 0; - return 0; -} - -static void nxt2002_release(struct dvb_frontend* fe) -{ - struct nxt2002_state* state = fe->demodulator_priv; - kfree(state); -} - -static struct dvb_frontend_ops nxt2002_ops; - -struct dvb_frontend* nxt2002_attach(const struct nxt2002_config* config, - struct i2c_adapter* i2c) -{ - struct nxt2002_state* state = NULL; - u8 buf [] = {0,0,0,0,0}; - - /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct nxt2002_state), GFP_KERNEL); - if (state == NULL) goto error; - - /* setup the state */ - state->config = config; - state->i2c = i2c; - memcpy(&state->ops, &nxt2002_ops, sizeof(struct dvb_frontend_ops)); - state->initialised = 0; - - /* Check the first 5 registers to ensure this a revision we can handle */ - - i2c_readbytes(state, 0x00, buf, 5); - if (buf[0] != 0x04) goto error; /* device id */ - if (buf[1] != 0x02) goto error; /* fab id */ - if (buf[2] != 0x11) goto error; /* month */ - if (buf[3] != 0x20) goto error; /* year msb */ - if (buf[4] != 0x00) goto error; /* year lsb */ - - /* create dvb_frontend */ - state->frontend.ops = &state->ops; - state->frontend.demodulator_priv = state; - return &state->frontend; - -error: - kfree(state); - return NULL; -} - -static struct dvb_frontend_ops nxt2002_ops = { - - .info = { - .name = "Nextwave nxt2002 VSB/QAM frontend", - .type = FE_ATSC, - .frequency_min = 54000000, - .frequency_max = 860000000, - /* stepsize is just a guess */ - .frequency_stepsize = 166666, - .caps = FE_CAN_FEC_1_2 | FE_CAN_FEC_2_3 | FE_CAN_FEC_3_4 | - FE_CAN_FEC_5_6 | FE_CAN_FEC_7_8 | FE_CAN_FEC_AUTO | - FE_CAN_8VSB | FE_CAN_QAM_64 | FE_CAN_QAM_256 - }, - - .release = nxt2002_release, - - .init = nxt2002_init, - .sleep = nxt2002_sleep, - - .set_frontend = nxt2002_setup_frontend_parameters, - .get_tune_settings = nxt2002_get_tune_settings, - - .read_status = nxt2002_read_status, - .read_ber = nxt2002_read_ber, - .read_signal_strength = nxt2002_read_signal_strength, - .read_snr = nxt2002_read_snr, - .read_ucblocks = nxt2002_read_ucblocks, - -}; - -module_param(debug, int, 0644); -MODULE_PARM_DESC(debug, "Turn on/off frontend debugging (default:off)."); - -MODULE_DESCRIPTION("NXT2002 ATSC (8VSB & ITU J83 AnnexB FEC QAM64/256) demodulator driver"); -MODULE_AUTHOR("Taylor Jacob"); -MODULE_LICENSE("GPL"); - -EXPORT_SYMBOL(nxt2002_attach); diff --git a/drivers/media/dvb/frontends/nxt2002.h b/drivers/media/dvb/frontends/nxt2002.h deleted file mode 100644 index 462301f577e..00000000000 --- a/drivers/media/dvb/frontends/nxt2002.h +++ /dev/null @@ -1,23 +0,0 @@ -/* - Driver for the Nxt2002 demodulator -*/ - -#ifndef NXT2002_H -#define NXT2002_H - -#include <linux/dvb/frontend.h> -#include <linux/firmware.h> - -struct nxt2002_config -{ - /* the demodulator's i2c address */ - u8 demod_address; - - /* request firmware for device */ - int (*request_firmware)(struct dvb_frontend* fe, const struct firmware **fw, char* name); -}; - -extern struct dvb_frontend* nxt2002_attach(const struct nxt2002_config* config, - struct i2c_adapter* i2c); - -#endif // NXT2002_H diff --git a/drivers/media/dvb/frontends/nxt200x.c b/drivers/media/dvb/frontends/nxt200x.c index 78d2b93d35b..9e353539450 100644 --- a/drivers/media/dvb/frontends/nxt200x.c +++ b/drivers/media/dvb/frontends/nxt200x.c @@ -1,9 +1,10 @@ /* * Support for NXT2002 and NXT2004 - VSB/QAM * - * Copyright (C) 2005 Kirk Lapray (kirk.lapray@gmail.com) + * Copyright (C) 2005 Kirk Lapray <kirk.lapray@gmail.com> + * Copyright (C) 2006 Michael Krufky <mkrufky@m1k.net> * based on nxt2002 by Taylor Jacob <rtjacob@earthlink.net> - * and nxt2004 by Jean-Francois Thibert (jeanfrancois@sagetv.com) + * and nxt2004 by Jean-Francois Thibert <jeanfrancois@sagetv.com> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -614,7 +615,17 @@ static int nxt200x_setup_frontend_parameters (struct dvb_frontend* fe, /* write sdm1 input */ buf[0] = 0x10; buf[1] = 0x00; - nxt200x_writebytes(state, 0x58, buf, 2); + switch (state->demod_chip) { + case NXT2002: + nxt200x_writereg_multibyte(state, 0x58, buf, 2); + break; + case NXT2004: + nxt200x_writebytes(state, 0x58, buf, 2); + break; + default: + return -EINVAL; + break; + } /* write sdmx input */ switch (p->u.vsb.modulation) { @@ -632,7 +643,17 @@ static int nxt200x_setup_frontend_parameters (struct dvb_frontend* fe, break; } buf[1] = 0x00; - nxt200x_writebytes(state, 0x5C, buf, 2); + switch (state->demod_chip) { + case NXT2002: + nxt200x_writereg_multibyte(state, 0x5C, buf, 2); + break; + case NXT2004: + nxt200x_writebytes(state, 0x5C, buf, 2); + break; + default: + return -EINVAL; + break; + } /* write adc power lpf fc */ buf[0] = 0x05; @@ -648,7 +669,17 @@ static int nxt200x_setup_frontend_parameters (struct dvb_frontend* fe, /* write accumulator2 input */ buf[0] = 0x80; buf[1] = 0x00; - nxt200x_writebytes(state, 0x4B, buf, 2); + switch (state->demod_chip) { + case NXT2002: + nxt200x_writereg_multibyte(state, 0x4B, buf, 2); + break; + case NXT2004: + nxt200x_writebytes(state, 0x4B, buf, 2); + break; + default: + return -EINVAL; + break; + } /* write kg1 */ buf[0] = 0x00; @@ -714,8 +745,19 @@ static int nxt200x_setup_frontend_parameters (struct dvb_frontend* fe, /* write accumulator2 input */ buf[0] = 0x80; buf[1] = 0x00; - nxt200x_writebytes(state, 0x49, buf,2); - nxt200x_writebytes(state, 0x4B, buf,2); + switch (state->demod_chip) { + case NXT2002: + nxt200x_writereg_multibyte(state, 0x49, buf, 2); + nxt200x_writereg_multibyte(state, 0x4B, buf, 2); + break; + case NXT2004: + nxt200x_writebytes(state, 0x49, buf, 2); + nxt200x_writebytes(state, 0x4B, buf, 2); + break; + default: + return -EINVAL; + break; + } /* write agc control reg */ buf[0] = 0x04; @@ -1199,7 +1241,7 @@ module_param(debug, int, 0644); MODULE_PARM_DESC(debug, "Turn on/off frontend debugging (default:off)."); MODULE_DESCRIPTION("NXT200X (ATSC 8VSB & ITU-T J.83 AnnexB 64/256 QAM) Demodulator Driver"); -MODULE_AUTHOR("Kirk Lapray, Jean-Francois Thibert, and Taylor Jacob"); +MODULE_AUTHOR("Kirk Lapray, Michael Krufky, Jean-Francois Thibert, and Taylor Jacob"); MODULE_LICENSE("GPL"); EXPORT_SYMBOL(nxt200x_attach); diff --git a/drivers/media/dvb/frontends/tda80xx.c b/drivers/media/dvb/frontends/tda80xx.c deleted file mode 100644 index d1cabb6a0a1..00000000000 --- a/drivers/media/dvb/frontends/tda80xx.c +++ /dev/null @@ -1,734 +0,0 @@ -/* - * tda80xx.c - * - * Philips TDA8044 / TDA8083 QPSK demodulator driver - * - * Copyright (C) 2001 Felix Domke <tmbinc@elitedvb.net> - * Copyright (C) 2002-2004 Andreas Oberritter <obi@linuxtv.org> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - */ - -#include <linux/config.h> -#include <linux/delay.h> -#include <linux/init.h> -#include <linux/spinlock.h> -#include <linux/threads.h> -#include <linux/interrupt.h> -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/slab.h> -#include <asm/irq.h> -#include <asm/div64.h> - -#include "dvb_frontend.h" -#include "tda80xx.h" - -enum { - ID_TDA8044 = 0x04, - ID_TDA8083 = 0x05, -}; - - -struct tda80xx_state { - - struct i2c_adapter* i2c; - - struct dvb_frontend_ops ops; - - /* configuration settings */ - const struct tda80xx_config* config; - - struct dvb_frontend frontend; - - u32 clk; - int afc_loop; - struct work_struct worklet; - fe_code_rate_t code_rate; - fe_spectral_inversion_t spectral_inversion; - fe_status_t status; - u8 id; -}; - -static int debug = 1; -#define dprintk if (debug) printk - -static u8 tda8044_inittab_pre[] = { - 0x02, 0x00, 0x6f, 0xb5, 0x86, 0x22, 0x00, 0xea, - 0x30, 0x42, 0x98, 0x68, 0x70, 0x42, 0x99, 0x58, - 0x95, 0x10, 0xf5, 0xe7, 0x93, 0x0b, 0x15, 0x68, - 0x9a, 0x90, 0x61, 0x80, 0x00, 0xe0, 0x40, 0x00, - 0x0f, 0x15, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, - 0x00, 0x00 -}; - -static u8 tda8044_inittab_post[] = { - 0x04, 0x00, 0x6f, 0xb5, 0x86, 0x22, 0x00, 0xea, - 0x30, 0x42, 0x98, 0x68, 0x70, 0x42, 0x99, 0x50, - 0x95, 0x10, 0xf5, 0xe7, 0x93, 0x0b, 0x15, 0x68, - 0x9a, 0x90, 0x61, 0x80, 0x00, 0xe0, 0x40, 0x6c, - 0x0f, 0x15, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, - 0x00, 0x00 -}; - -static u8 tda8083_inittab[] = { - 0x04, 0x00, 0x4a, 0x79, 0x04, 0x00, 0xff, 0xea, - 0x48, 0x42, 0x79, 0x60, 0x70, 0x52, 0x9a, 0x10, - 0x0e, 0x10, 0xf2, 0xa7, 0x93, 0x0b, 0x05, 0xc8, - 0x9d, 0x00, 0x42, 0x80, 0x00, 0x60, 0x40, 0x00, - 0x00, 0x75, 0x00, 0xe0, 0x00, 0x00, 0x00, 0x00, - 0x00, 0x00, 0x00, 0x00 -}; - -static __inline__ u32 tda80xx_div(u32 a, u32 b) -{ - return (a + (b / 2)) / b; -} - -static __inline__ u32 tda80xx_gcd(u32 a, u32 b) -{ - u32 r; - - while ((r = a % b)) { - a = b; - b = r; - } - - return b; -} - -static int tda80xx_read(struct tda80xx_state* state, u8 reg, u8 *buf, u8 len) -{ - int ret; - struct i2c_msg msg[] = { { .addr = state->config->demod_address, .flags = 0, .buf = ®, .len = 1 }, - { .addr = state->config->demod_address, .flags = I2C_M_RD, .buf = buf, .len = len } }; - - ret = i2c_transfer(state->i2c, msg, 2); - - if (ret != 2) - dprintk("%s: readreg error (reg %02x, ret == %i)\n", - __FUNCTION__, reg, ret); - - mdelay(10); - - return (ret == 2) ? 0 : -EREMOTEIO; -} - -static int tda80xx_write(struct tda80xx_state* state, u8 reg, const u8 *buf, u8 len) -{ - int ret; - u8 wbuf[len + 1]; - struct i2c_msg msg = { .addr = state->config->demod_address, .flags = 0, .buf = wbuf, .len = len + 1 }; - - wbuf[0] = reg; - memcpy(&wbuf[1], buf, len); - - ret = i2c_transfer(state->i2c, &msg, 1); - - if (ret != 1) - dprintk("%s: i2c xfer error (ret == %i)\n", __FUNCTION__, ret); - - mdelay(10); - - return (ret == 1) ? 0 : -EREMOTEIO; -} - -static __inline__ u8 tda80xx_readreg(struct tda80xx_state* state, u8 reg) -{ - u8 val; - - tda80xx_read(state, reg, &val, 1); - - return val; -} - -static __inline__ int tda80xx_writereg(struct tda80xx_state* state, u8 reg, u8 data) -{ - return tda80xx_write(state, reg, &data, 1); -} - -static int tda80xx_set_parameters(struct tda80xx_state* state, - fe_spectral_inversion_t inversion, - u32 symbol_rate, - fe_code_rate_t fec_inner) -{ - u8 buf[15]; - u64 ratio; - u32 clk; - u32 k; - u32 sr = symbol_rate; - u32 gcd; - u8 scd; - - if (symbol_rate > (state->clk * 3) / 16) - scd = 0; - else if (symbol_rate > (state->clk * 3) / 32) - scd = 1; - else if (symbol_rate > (state->clk * 3) / 64) - scd = 2; - else - scd = 3; - - clk = scd ? (state->clk / (scd * 2)) : state->clk; - - /* - * Viterbi decoder: - * Differential decoding off - * Spectral inversion unknown - * QPSK modulation - */ - if (inversion == INVERSION_ON) - buf[0] = 0x60; - else if (inversion == INVERSION_OFF) - buf[0] = 0x20; - else - buf[0] = 0x00; - - /* - * CLK ratio: - * system clock frequency is up to 64 or 96 MHz - * - * formula: - * r = k * clk / symbol_rate - * - * k: 2^21 for caa 0..3, - * 2^20 for caa 4..5, - * 2^19 for caa 6..7 - */ - if (symbol_rate <= (clk * 3) / 32) - k = (1 << 19); - else if (symbol_rate <= (clk * 3) / 16) - k = (1 << 20); - else - k = (1 << 21); - - gcd = tda80xx_gcd(clk, sr); - clk /= gcd; - sr /= gcd; - - gcd = tda80xx_gcd(k, sr); - k /= gcd; - sr /= gcd; - - ratio = (u64)k * (u64)clk; - do_div(ratio, sr); - - buf[1] = ratio >> 16; - buf[2] = ratio >> 8; - buf[3] = ratio; - - /* nyquist filter roll-off factor 35% */ - buf[4] = 0x20; - - clk = scd ? (state->clk / (scd * 2)) : state->clk; - - /* Anti Alias Filter */ - if (symbol_rate < (clk * 3) / 64) - printk("tda80xx: unsupported symbol rate: %u\n", symbol_rate); - else if (symbol_rate <= clk / 16) - buf[4] |= 0x07; - else if (symbol_rate <= (clk * 3) / 32) - buf[4] |= 0x06; - else if (symbol_rate <= clk / 8) - buf[4] |= 0x05; - else if (symbol_rate <= (clk * 3) / 16) - buf[4] |= 0x04; - else if (symbol_rate <= clk / 4) - buf[4] |= 0x03; - else if (symbol_rate <= (clk * 3) / 8) - buf[4] |= 0x02; - else if (symbol_rate <= clk / 2) - buf[4] |= 0x01; - else - buf[4] |= 0x00; - - /* Sigma Delta converter */ - buf[5] = 0x00; - - /* FEC: Possible puncturing rates */ - if (fec_inner == FEC_NONE) - buf[6] = 0x00; - else if ((fec_inner >= FEC_1_2) && (fec_inner <= FEC_8_9)) - buf[6] = (1 << (8 - fec_inner)); - else if (fec_inner == FEC_AUTO) - buf[6] = 0xff; - else - return -EINVAL; - - /* carrier lock detector threshold value */ - buf[7] = 0x30; - /* AFC1: proportional part settings */ - buf[8] = 0x42; - /* AFC1: integral part settings */ - buf[9] = 0x98; - /* PD: Leaky integrator SCPC mode */ - buf[10] = 0x28; - /* AFC2, AFC1 controls */ - buf[11] = 0x30; - /* PD: proportional part settings */ - buf[12] = 0x42; - /* PD: integral part settings */ - buf[13] = 0x99; - /* AGC */ - buf[14] = 0x50 | scd; - - printk("symbol_rate=%u clk=%u\n", symbol_rate, clk); - - return tda80xx_write(state, 0x01, buf, sizeof(buf)); -} - -static int tda80xx_set_clk(struct tda80xx_state* state) -{ - u8 buf[2]; - - /* CLK proportional part */ - buf[0] = (0x06 << 5) | 0x08; /* CMP[2:0], CSP[4:0] */ - /* CLK integral part */ - buf[1] = (0x04 << 5) | 0x1a; /* CMI[2:0], CSI[4:0] */ - - return tda80xx_write(state, 0x17, buf, sizeof(buf)); -} - -#if 0 -static int tda80xx_set_scpc_freq_offset(struct tda80xx_state* state) -{ - /* a constant value is nonsense here imho */ - return tda80xx_writereg(state, 0x22, 0xf9); -} -#endif - -static int tda80xx_close_loop(struct tda80xx_state* state) -{ - u8 buf[2]; - - /* PD: Loop closed, LD: lock detect enable, SCPC: Sweep mode - AFC1 loop closed */ - buf[0] = 0x68; - /* AFC1: Loop closed, CAR Feedback: 8192 */ - buf[1] = 0x70; - - return tda80xx_write(state, 0x0b, buf, sizeof(buf)); -} - -static irqreturn_t tda80xx_irq(int irq, void *priv, struct pt_regs *pt) -{ - schedule_work(priv); - - return IRQ_HANDLED; -} - -static void tda80xx_read_status_int(struct tda80xx_state* state) -{ - u8 val; - - static const fe_spectral_inversion_t inv_tab[] = { - INVERSION_OFF, INVERSION_ON - }; - - static const fe_code_rate_t fec_tab[] = { - FEC_8_9, FEC_1_2, FEC_2_3, FEC_3_4, - FEC_4_5, FEC_5_6, FEC_6_7, FEC_7_8, - }; - - val = tda80xx_readreg(state, 0x02); - - state->status = 0; - - if (val & 0x01) /* demodulator lock */ - state->status |= FE_HAS_SIGNAL; - if (val & 0x02) /* clock recovery lock */ - state->status |= FE_HAS_CARRIER; - if (val & 0x04) /* viterbi lock */ - state->status |= FE_HAS_VITERBI; - if (val & 0x08) /* deinterleaver lock (packet sync) */ - state->status |= FE_HAS_SYNC; - if (val & 0x10) /* derandomizer lock (frame sync) */ - state->status |= FE_HAS_LOCK; - if (val & 0x20) /* frontend can not lock */ - state->status |= FE_TIMEDOUT; - - if ((state->status & (FE_HAS_CARRIER)) && (state->afc_loop)) { - printk("tda80xx: closing loop\n"); - tda80xx_close_loop(state); - state->afc_loop = 0; - } - - if (state->status & (FE_HAS_VITERBI | FE_HAS_SYNC | FE_HAS_LOCK)) { - val = tda80xx_readreg(state, 0x0e); - state->code_rate = fec_tab[val & 0x07]; - if (state->status & (FE_HAS_SYNC | FE_HAS_LOCK)) - state->spectral_inversion = inv_tab[(val >> 7) & 0x01]; - else - state->spectral_inversion = INVERSION_AUTO; - } - else { - state->code_rate = FEC_AUTO; - } -} - -static void tda80xx_worklet(void *priv) -{ - struct tda80xx_state *state = priv; - - tda80xx_writereg(state, 0x00, 0x04); - enable_irq(state->config->irq); - - tda80xx_read_status_int(state); -} - -static void tda80xx_wait_diseqc_fifo(struct tda80xx_state* state) -{ - size_t i; - - for (i = 0; i < 100; i++) { - if (tda80xx_readreg(state, 0x02) & 0x80) - break; - msleep(10); - } -} - -static int tda8044_init(struct dvb_frontend* fe) -{ - struct tda80xx_state* state = fe->demodulator_priv; - int ret; - - /* - * this function is a mess... - */ - - if ((ret = tda80xx_write(state, 0x00, tda8044_inittab_pre, sizeof(tda8044_inittab_pre)))) - return ret; - - tda80xx_writereg(state, 0x0f, 0x50); -#if 1 - tda80xx_writereg(state, 0x20, 0x8F); /* FIXME */ - tda80xx_writereg(state, 0x20, state->config->volt18setting); /* FIXME */ - //tda80xx_writereg(state, 0x00, 0x04); - tda80xx_writereg(state, 0x00, 0x0C); -#endif - //tda80xx_writereg(state, 0x00, 0x08); /* Reset AFC1 loop filter */ - - tda80xx_write(state, 0x00, tda8044_inittab_post, sizeof(tda8044_inittab_post)); - - if (state->config->pll_init) { - tda80xx_writereg(state, 0x1c, 0x80); - state->config->pll_init(fe); - tda80xx_writereg(state, 0x1c, 0x00); - } - - return 0; -} - -static int tda8083_init(struct dvb_frontend* fe) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - tda80xx_write(state, 0x00, tda8083_inittab, sizeof(tda8083_inittab)); - - if (state->config->pll_init) { - tda80xx_writereg(state, 0x1c, 0x80); - state->config->pll_init(fe); - tda80xx_writereg(state, 0x1c, 0x00); - } - - return 0; -} - -static int tda80xx_set_voltage(struct dvb_frontend* fe, fe_sec_voltage_t voltage) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - switch (voltage) { - case SEC_VOLTAGE_13: - return tda80xx_writereg(state, 0x20, state->config->volt13setting); - case SEC_VOLTAGE_18: - return tda80xx_writereg(state, 0x20, state->config->volt18setting); - case SEC_VOLTAGE_OFF: - return tda80xx_writereg(state, 0x20, 0); - default: - return -EINVAL; - } -} - -static int tda80xx_set_tone(struct dvb_frontend* fe, fe_sec_tone_mode_t tone) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - switch (tone) { - case SEC_TONE_OFF: - return tda80xx_writereg(state, 0x29, 0x00); - case SEC_TONE_ON: - return tda80xx_writereg(state, 0x29, 0x80); - default: - return -EINVAL; - } -} - -static int tda80xx_send_diseqc_msg(struct dvb_frontend* fe, struct dvb_diseqc_master_cmd *cmd) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - if (cmd->msg_len > 6) - return -EINVAL; - - tda80xx_writereg(state, 0x29, 0x08 | (cmd->msg_len - 3)); - tda80xx_write(state, 0x23, cmd->msg, cmd->msg_len); - tda80xx_writereg(state, 0x29, 0x0c | (cmd->msg_len - 3)); - tda80xx_wait_diseqc_fifo(state); - - return 0; -} - -static int tda80xx_send_diseqc_burst(struct dvb_frontend* fe, fe_sec_mini_cmd_t cmd) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - switch (cmd) { - case SEC_MINI_A: - tda80xx_writereg(state, 0x29, 0x14); - break; - case SEC_MINI_B: - tda80xx_writereg(state, 0x29, 0x1c); - break; - default: - return -EINVAL; - } - - tda80xx_wait_diseqc_fifo(state); - - return 0; -} - -static int tda80xx_sleep(struct dvb_frontend* fe) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - tda80xx_writereg(state, 0x00, 0x02); /* enter standby */ - - return 0; -} - -static int tda80xx_set_frontend(struct dvb_frontend* fe, struct dvb_frontend_parameters *p) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - tda80xx_writereg(state, 0x1c, 0x80); - state->config->pll_set(fe, p); - tda80xx_writereg(state, 0x1c, 0x00); - - tda80xx_set_parameters(state, p->inversion, p->u.qpsk.symbol_rate, p->u.qpsk.fec_inner); - tda80xx_set_clk(state); - //tda80xx_set_scpc_freq_offset(state); - state->afc_loop = 1; - - return 0; -} - -static int tda80xx_get_frontend(struct dvb_frontend* fe, struct dvb_frontend_parameters *p) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - if (!state->config->irq) - tda80xx_read_status_int(state); - - p->inversion = state->spectral_inversion; - p->u.qpsk.fec_inner = state->code_rate; - - return 0; -} - -static int tda80xx_read_status(struct dvb_frontend* fe, fe_status_t* status) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - if (!state->config->irq) - tda80xx_read_status_int(state); - *status = state->status; - - return 0; -} - -static int tda80xx_read_ber(struct dvb_frontend* fe, u32* ber) -{ - struct tda80xx_state* state = fe->demodulator_priv; - int ret; - u8 buf[3]; - - if ((ret = tda80xx_read(state, 0x0b, buf, sizeof(buf)))) - return ret; - - *ber = ((buf[0] & 0x1f) << 16) | (buf[1] << 8) | buf[2]; - - return 0; -} - -static int tda80xx_read_signal_strength(struct dvb_frontend* fe, u16* strength) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - u8 gain = ~tda80xx_readreg(state, 0x01); - *strength = (gain << 8) | gain; - - return 0; -} - -static int tda80xx_read_snr(struct dvb_frontend* fe, u16* snr) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - u8 quality = tda80xx_readreg(state, 0x08); - *snr = (quality << 8) | quality; - - return 0; -} - -static int tda80xx_read_ucblocks(struct dvb_frontend* fe, u32* ucblocks) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - *ucblocks = tda80xx_readreg(state, 0x0f); - if (*ucblocks == 0xff) - *ucblocks = 0xffffffff; - - return 0; -} - -static int tda80xx_init(struct dvb_frontend* fe) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - switch(state->id) { - case ID_TDA8044: - return tda8044_init(fe); - - case ID_TDA8083: - return tda8083_init(fe); - } - return 0; -} - -static void tda80xx_release(struct dvb_frontend* fe) -{ - struct tda80xx_state* state = fe->demodulator_priv; - - if (state->config->irq) - free_irq(state->config->irq, &state->worklet); - - kfree(state); -} - -static struct dvb_frontend_ops tda80xx_ops; - -struct dvb_frontend* tda80xx_attach(const struct tda80xx_config* config, - struct i2c_adapter* i2c) -{ - struct tda80xx_state* state = NULL; - int ret; - - /* allocate memory for the internal state */ - state = kmalloc(sizeof(struct tda80xx_state), GFP_KERNEL); - if (state == NULL) goto error; - - /* setup the state */ - state->config = config; - state->i2c = i2c; - memcpy(&state->ops, &tda80xx_ops, sizeof(struct dvb_frontend_ops)); - state->spectral_inversion = INVERSION_AUTO; - state->code_rate = FEC_AUTO; - state->status = 0; - state->afc_loop = 0; - - /* check if the demod is there */ - if (tda80xx_writereg(state, 0x89, 0x00) < 0) goto error; - state->id = tda80xx_readreg(state, 0x00); - - switch (state->id) { - case ID_TDA8044: - state->clk = 96000000; - printk("tda80xx: Detected tda8044\n"); - break; - - case ID_TDA8083: - state->clk = 64000000; - printk("tda80xx: Detected tda8083\n"); - break; - - default: - goto error; - } - - /* setup IRQ */ - if (state->config->irq) { - INIT_WORK(&state->worklet, tda80xx_worklet, state); - if ((ret = request_irq(state->config->irq, tda80xx_irq, SA_ONESHOT, "tda80xx", &state->worklet)) < 0) { - printk(KERN_ERR "tda80xx: request_irq failed (%d)\n", ret); - goto error; - } - } - - /* create dvb_frontend */ - state->frontend.ops = &state->ops; - state->frontend.demodulator_priv = state; - return &state->frontend; - -error: - kfree(state); - return NULL; -} - -static struct dvb_frontend_ops tda80xx_ops = { - - .info = { - .name = "Philips TDA80xx DVB-S", - .type = FE_QPSK, - .frequency_min = 500000, - .frequency_max = 2700000, - .frequency_stepsize = 125, - .symbol_rate_min = 4500000, - .symbol_rate_max = 45000000, - .caps = FE_CAN_INVERSION_AUTO | - FE_CAN_FEC_1_2 | FE_CAN_FEC_2_3 | FE_CAN_FEC_3_4 | - FE_CAN_FEC_4_5 | FE_CAN_FEC_5_6 | FE_CAN_FEC_6_7 | - FE_CAN_FEC_7_8 | FE_CAN_FEC_8_9 | FE_CAN_FEC_AUTO | - FE_CAN_QPSK | - FE_CAN_MUTE_TS - }, - - .release = tda80xx_release, - - .init = tda80xx_init, - .sleep = tda80xx_sleep, - - .set_frontend = tda80xx_set_frontend, - .get_frontend = tda80xx_get_frontend, - - .read_status = tda80xx_read_status, - .read_ber = tda80xx_read_ber, - .read_signal_strength = tda80xx_read_signal_strength, - .read_snr = tda80xx_read_snr, - .read_ucblocks = tda80xx_read_ucblocks, - - .diseqc_send_master_cmd = tda80xx_send_diseqc_msg, - .diseqc_send_burst = tda80xx_send_diseqc_burst, - .set_tone = tda80xx_set_tone, - .set_voltage = tda80xx_set_voltage, -}; - -module_param(debug, int, 0644); - -MODULE_DESCRIPTION("Philips TDA8044 / TDA8083 DVB-S Demodulator driver"); -MODULE_AUTHOR("Felix Domke, Andreas Oberritter"); -MODULE_LICENSE("GPL"); - -EXPORT_SYMBOL(tda80xx_attach); diff --git a/drivers/media/dvb/frontends/tda80xx.h b/drivers/media/dvb/frontends/tda80xx.h deleted file mode 100644 index cd639a0aad5..00000000000 --- a/drivers/media/dvb/frontends/tda80xx.h +++ /dev/null @@ -1,51 +0,0 @@ -/* - * tda80xx.c - * - * Philips TDA8044 / TDA8083 QPSK demodulator driver - * - * Copyright (C) 2001 Felix Domke <tmbinc@elitedvb.net> - * Copyright (C) 2002-2004 Andreas Oberritter <obi@linuxtv.org> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - */ - -#ifndef TDA80XX_H -#define TDA80XX_H - -#include <linux/dvb/frontend.h> - -struct tda80xx_config -{ - /* the demodulator's i2c address */ - u8 demod_address; - - /* IRQ to use (0=>no IRQ used) */ - u32 irq; - - /* Register setting to use for 13v */ - u8 volt13setting; - - /* Register setting to use for 18v */ - u8 volt18setting; - - /* PLL maintenance */ - int (*pll_init)(struct dvb_frontend* fe); - int (*pll_set)(struct dvb_frontend* fe, struct dvb_frontend_parameters* params); -}; - -extern struct dvb_frontend* tda80xx_attach(const struct tda80xx_config* config, - struct i2c_adapter* i2c); - -#endif // TDA80XX_H diff --git a/drivers/media/dvb/ttpci/av7110.c b/drivers/media/dvb/ttpci/av7110.c index 27494901975..d36369e9e88 100644 --- a/drivers/media/dvb/ttpci/av7110.c +++ b/drivers/media/dvb/ttpci/av7110.c @@ -2329,6 +2329,17 @@ static int frontend_init(struct av7110 *av7110) av7110->fe = ves1820_attach(&alps_tdbe2_config, &av7110->i2c_adap, read_pwm(av7110)); break; + case 0x0004: // Galaxis DVB-S rev1.3 + /* ALPS BSRV2 */ + av7110->fe = ves1x93_attach(&alps_bsrv2_config, &av7110->i2c_adap); + if (av7110->fe) { + av7110->fe->ops->diseqc_send_master_cmd = av7110_diseqc_send_master_cmd; + av7110->fe->ops->diseqc_send_burst = av7110_diseqc_send_burst; + av7110->fe->ops->set_tone = av7110_set_tone; + av7110->recover = dvb_s_recover; + } + break; + case 0x0006: /* Fujitsu-Siemens DVB-S rev 1.6 */ /* Grundig 29504-451 */ av7110->fe = tda8083_attach(&grundig_29504_451_config, &av7110->i2c_adap); @@ -2930,6 +2941,7 @@ MAKE_AV7110_INFO(tts_1_3se, "Technotrend/Hauppauge WinTV DVB-S rev1.3 SE"); MAKE_AV7110_INFO(ttt, "Technotrend/Hauppauge DVB-T"); MAKE_AV7110_INFO(fsc, "Fujitsu Siemens DVB-C"); MAKE_AV7110_INFO(fss, "Fujitsu Siemens DVB-S rev1.6"); +MAKE_AV7110_INFO(gxs_1_3, "Galaxis DVB-S rev1.3"); static struct pci_device_id pci_tbl[] = { MAKE_EXTENSION_PCI(fsc, 0x110a, 0x0000), @@ -2937,13 +2949,13 @@ static struct pci_device_id pci_tbl[] = { MAKE_EXTENSION_PCI(ttt_1_X, 0x13c2, 0x0001), MAKE_EXTENSION_PCI(ttc_2_X, 0x13c2, 0x0002), MAKE_EXTENSION_PCI(tts_2_X, 0x13c2, 0x0003), + MAKE_EXTENSION_PCI(gxs_1_3, 0x13c2, 0x0004), MAKE_EXTENSION_PCI(fss, 0x13c2, 0x0006), MAKE_EXTENSION_PCI(ttt, 0x13c2, 0x0008), MAKE_EXTENSION_PCI(ttc_1_X, 0x13c2, 0x000a), MAKE_EXTENSION_PCI(tts_2_3, 0x13c2, 0x000e), MAKE_EXTENSION_PCI(tts_1_3se, 0x13c2, 0x1002), -/* MAKE_EXTENSION_PCI(???, 0x13c2, 0x0004), UNDEFINED CARD */ // Galaxis DVB PC-Sat-Carte /* MAKE_EXTENSION_PCI(???, 0x13c2, 0x0005), UNDEFINED CARD */ // Technisat SkyStar1 /* MAKE_EXTENSION_PCI(???, 0x13c2, 0x0009), UNDEFINED CARD */ // TT/Hauppauge WinTV Nexus-CA v???? diff --git a/drivers/media/dvb/ttpci/av7110.h b/drivers/media/dvb/ttpci/av7110.h index 6ea30df2e82..fafd25fab83 100644 --- a/drivers/media/dvb/ttpci/av7110.h +++ b/drivers/media/dvb/ttpci/av7110.h @@ -273,8 +273,6 @@ struct av7110 { extern int ChangePIDs(struct av7110 *av7110, u16 vpid, u16 apid, u16 ttpid, u16 subpid, u16 pcrpid); -extern int av7110_setup_irc_config (struct av7110 *av7110, u32 ir_config); - extern int av7110_ir_init(struct av7110 *av7110); extern void av7110_ir_exit(struct av7110 *av7110); diff --git a/drivers/media/dvb/ttpci/av7110_ir.c b/drivers/media/dvb/ttpci/av7110_ir.c index 9138132ad25..617e4f6c0ed 100644 --- a/drivers/media/dvb/ttpci/av7110_ir.c +++ b/drivers/media/dvb/ttpci/av7110_ir.c @@ -155,6 +155,19 @@ static void input_repeat_key(unsigned long data) } +static int av7110_setup_irc_config(struct av7110 *av7110, u32 ir_config) +{ + int ret = 0; + + dprintk(4, "%p\n", av7110); + if (av7110) { + ret = av7110_fw_cmd(av7110, COMTYPE_PIDFILTER, SetIR, 1, ir_config); + av7110->ir_config = ir_config; + } + return ret; +} + + static int av7110_ir_write_proc(struct file *file, const char __user *buffer, unsigned long count, void *data) { @@ -187,19 +200,6 @@ static int av7110_ir_write_proc(struct file *file, const char __user *buffer, } -int av7110_setup_irc_config(struct av7110 *av7110, u32 ir_config) -{ - int ret = 0; - - dprintk(4, "%p\n", av7110); - if (av7110) { - ret = av7110_fw_cmd(av7110, COMTYPE_PIDFILTER, SetIR, 1, ir_config); - av7110->ir_config = ir_config; - } - return ret; -} - - static void ir_handler(struct av7110 *av7110, u32 ircom) { dprintk(4, "ircommand = %08x\n", ircom); diff --git a/drivers/media/video/bttv-driver.c b/drivers/media/video/bttv-driver.c index aa4c4c52188..578b2008508 100644 --- a/drivers/media/video/bttv-driver.c +++ b/drivers/media/video/bttv-driver.c @@ -214,7 +214,7 @@ const struct bttv_tvnorm bttv_tvnorms[] = { we can capture, of the first and second field. */ .vbistart = { 7,320 }, },{ - .v4l2_id = V4L2_STD_NTSC_M, + .v4l2_id = V4L2_STD_NTSC_M | V4L2_STD_NTSC_M_KR, .name = "NTSC", .Fsc = 28636363, .swidth = 768, diff --git a/drivers/media/video/cx25840/cx25840-core.c b/drivers/media/video/cx25840/cx25840-core.c index c66c2c1f480..08ffd1f325f 100644 --- a/drivers/media/video/cx25840/cx25840-core.c +++ b/drivers/media/video/cx25840/cx25840-core.c @@ -220,33 +220,23 @@ static void input_change(struct i2c_client *client) cx25840_write(client, 0x808, 0xff); cx25840_write(client, 0x80b, 0x10); } else if (std & V4L2_STD_NTSC) { - /* NTSC */ - if (state->pvr150_workaround) { - /* Certain Hauppauge PVR150 models have a hardware bug - that causes audio to drop out. For these models the - audio standard must be set explicitly. - To be precise: it affects cards with tuner models - 85, 99 and 112 (model numbers from tveeprom). */ - if (std == V4L2_STD_NTSC_M_JP) { - /* Japan uses EIAJ audio standard */ - cx25840_write(client, 0x808, 0x2f); - } else { - /* Others use the BTSC audio standard */ - cx25840_write(client, 0x808, 0x1f); - } - /* South Korea uses the A2-M (aka Zweiton M) audio - standard, and should set 0x808 to 0x3f, but I don't - know how to detect this. */ - } else if (std == V4L2_STD_NTSC_M_JP) { + /* Certain Hauppauge PVR150 models have a hardware bug + that causes audio to drop out. For these models the + audio standard must be set explicitly. + To be precise: it affects cards with tuner models + 85, 99 and 112 (model numbers from tveeprom). */ + int hw_fix = state->pvr150_workaround; + + if (std == V4L2_STD_NTSC_M_JP) { /* Japan uses EIAJ audio standard */ - cx25840_write(client, 0x808, 0xf7); + cx25840_write(client, 0x808, hw_fix ? 0x2f : 0xf7); + } else if (std == V4L2_STD_NTSC_M_KR) { + /* South Korea uses A2 audio standard */ + cx25840_write(client, 0x808, hw_fix ? 0x3f : 0xf8); } else { /* Others use the BTSC audio standard */ - cx25840_write(client, 0x808, 0xf6); + cx25840_write(client, 0x808, hw_fix ? 0x1f : 0xf6); } - /* South Korea uses the A2-M (aka Zweiton M) audio standard, - and should set 0x808 to 0xf8, but I don't know how to - detect this. */ cx25840_write(client, 0x80b, 0x00); } @@ -330,17 +320,17 @@ static int set_v4lstd(struct i2c_client *client, v4l2_std_id std) u8 fmt=0; /* zero is autodetect */ /* First tests should be against specific std */ - if (std & V4L2_STD_NTSC_M_JP) { + if (std == V4L2_STD_NTSC_M_JP) { fmt=0x2; - } else if (std & V4L2_STD_NTSC_443) { + } else if (std == V4L2_STD_NTSC_443) { fmt=0x3; - } else if (std & V4L2_STD_PAL_M) { + } else if (std == V4L2_STD_PAL_M) { fmt=0x5; - } else if (std & V4L2_STD_PAL_N) { + } else if (std == V4L2_STD_PAL_N) { fmt=0x6; - } else if (std & V4L2_STD_PAL_Nc) { + } else if (std == V4L2_STD_PAL_Nc) { fmt=0x7; - } else if (std & V4L2_STD_PAL_60) { + } else if (std == V4L2_STD_PAL_60) { fmt=0x8; } else { /* Then, test against generic ones */ @@ -369,7 +359,7 @@ v4l2_std_id cx25840_get_v4lstd(struct i2c_client * client) } switch (fmt) { - case 0x1: return V4L2_STD_NTSC_M; + case 0x1: return V4L2_STD_NTSC_M | V4L2_STD_NTSC_M_KR; case 0x2: return V4L2_STD_NTSC_M_JP; case 0x3: return V4L2_STD_NTSC_443; case 0x4: return V4L2_STD_PAL; diff --git a/drivers/media/video/cx88/Kconfig b/drivers/media/video/cx88/Kconfig index 53308911ae6..e99dfbbf3e9 100644 --- a/drivers/media/video/cx88/Kconfig +++ b/drivers/media/video/cx88/Kconfig @@ -32,6 +32,7 @@ config VIDEO_CX88_DVB config VIDEO_CX88_ALSA tristate "ALSA DMA audio support" depends on VIDEO_CX88 && SND && EXPERIMENTAL + select SND_PCM ---help--- This is a video4linux driver for direct (DMA) audio on Conexant 2388x based TV cards. @@ -48,6 +49,7 @@ config VIDEO_CX88_DVB_ALL_FRONTENDS default y depends on VIDEO_CX88_DVB select DVB_MT352 + select VIDEO_CX88_VP3054 select DVB_OR51132 select DVB_CX22702 select DVB_LGDT330X @@ -69,6 +71,16 @@ config VIDEO_CX88_DVB_MT352 This adds DVB-T support for cards based on the Connexant 2388x chip and the MT352 demodulator. +config VIDEO_CX88_VP3054 + tristate "VP-3054 Secondary I2C Bus Support" + default m + depends on DVB_MT352 + ---help--- + This adds DVB-T support for cards based on the + Connexant 2388x chip and the MT352 demodulator, + which also require support for the VP-3054 + Secondary I2C bus, such at DNTV Live! DVB-T Pro. + config VIDEO_CX88_DVB_OR51132 bool "OR51132 ATSC Support" default y diff --git a/drivers/media/video/cx88/Makefile b/drivers/media/video/cx88/Makefile index 6e5eaa22619..2b902784fac 100644 --- a/drivers/media/video/cx88/Makefile +++ b/drivers/media/video/cx88/Makefile @@ -4,8 +4,9 @@ cx8800-objs := cx88-video.o cx88-vbi.o cx8802-objs := cx88-mpeg.o obj-$(CONFIG_VIDEO_CX88) += cx88xx.o cx8800.o cx8802.o cx88-blackbird.o -obj-$(CONFIG_VIDEO_CX88_DVB) += cx88-dvb.o cx88-vp3054-i2c.o +obj-$(CONFIG_VIDEO_CX88_DVB) += cx88-dvb.o obj-$(CONFIG_VIDEO_CX88_ALSA) += cx88-alsa.o +obj-$(CONFIG_VIDEO_CX88_VP3054) += cx88-vp3054-i2c.o EXTRA_CFLAGS += -I$(src)/.. EXTRA_CFLAGS += -I$(srctree)/drivers/media/dvb/dvb-core @@ -18,6 +19,6 @@ extra-cflags-$(CONFIG_DVB_LGDT330X) += -DHAVE_LGDT330X=1 extra-cflags-$(CONFIG_DVB_MT352) += -DHAVE_MT352=1 extra-cflags-$(CONFIG_DVB_NXT200X) += -DHAVE_NXT200X=1 extra-cflags-$(CONFIG_DVB_CX24123) += -DHAVE_CX24123=1 -extra-cflags-$(CONFIG_VIDEO_CX88_DVB)+= -DHAVE_VP3054_I2C=1 +extra-cflags-$(CONFIG_VIDEO_CX88_VP3054)+= -DHAVE_VP3054_I2C=1 EXTRA_CFLAGS += $(extra-cflags-y) $(extra-cflags-m) diff --git a/drivers/media/video/cx88/cx88-alsa.c b/drivers/media/video/cx88/cx88-alsa.c index a2e36a1e5f5..2acccd6d49b 100644 --- a/drivers/media/video/cx88/cx88-alsa.c +++ b/drivers/media/video/cx88/cx88-alsa.c @@ -128,7 +128,7 @@ MODULE_PARM_DESC(debug,"enable debug messages"); * BOARD Specific: Sets audio DMA */ -int _cx88_start_audio_dma(snd_cx88_card_t *chip) +static int _cx88_start_audio_dma(snd_cx88_card_t *chip) { struct cx88_buffer *buf = chip->buf; struct cx88_core *core=chip->core; @@ -173,7 +173,7 @@ int _cx88_start_audio_dma(snd_cx88_card_t *chip) /* * BOARD Specific: Resets audio DMA */ -int _cx88_stop_audio_dma(snd_cx88_card_t *chip) +static int _cx88_stop_audio_dma(snd_cx88_card_t *chip) { struct cx88_core *core=chip->core; dprintk(1, "Stopping audio DMA\n"); @@ -613,7 +613,7 @@ static snd_kcontrol_new_t snd_cx88_capture_volume = { * Only boards with eeprom and byte 1 at eeprom=1 have it */ -struct pci_device_id cx88_audio_pci_tbl[] = { +static struct pci_device_id cx88_audio_pci_tbl[] = { {0x14f1,0x8801,PCI_ANY_ID,PCI_ANY_ID,0,0,0}, {0x14f1,0x8811,PCI_ANY_ID,PCI_ANY_ID,0,0,0}, {0, } diff --git a/drivers/media/video/cx88/cx88-cards.c b/drivers/media/video/cx88/cx88-cards.c index ad2f565f522..1bc999247fd 100644 --- a/drivers/media/video/cx88/cx88-cards.c +++ b/drivers/media/video/cx88/cx88-cards.c @@ -1246,6 +1246,11 @@ struct cx88_subid cx88_subids[] = { .card = CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL, },{ .subvendor = 0x18ac, + .subdevice = 0xdb54, + .card = CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL, + /* Re-branded DViCO: DigitalNow DVB-T Dual */ + },{ + .subvendor = 0x18ac, .subdevice = 0xdb11, .card = CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PLUS, /* Re-branded DViCO: UltraView DVB-T Plus */ @@ -1293,6 +1298,7 @@ static void hauppauge_eeprom(struct cx88_core *core, u8 *eeprom_data) switch (tv.model) { case 28552: /* WinTV-PVR 'Roslyn' (No IR) */ + case 34519: /* WinTV-PCI-FM */ case 90002: /* Nova-T-PCI (9002) */ case 92001: /* Nova-S-Plus (Video and IR) */ case 92002: /* Nova-S-Plus (Video and IR) */ diff --git a/drivers/media/video/cx88/cx88-core.c b/drivers/media/video/cx88/cx88-core.c index 8d6d6a6cf78..3720f24a25c 100644 --- a/drivers/media/video/cx88/cx88-core.c +++ b/drivers/media/video/cx88/cx88-core.c @@ -787,12 +787,14 @@ static int set_pll(struct cx88_core *core, int prescale, u32 ofreq) int cx88_start_audio_dma(struct cx88_core *core) { + /* constant 128 made buzz in analog Nicam-stereo for bigger fifo_size */ + int bpl = cx88_sram_channels[SRAM_CH25].fifo_size/4; /* setup fifo + format */ - cx88_sram_channel_setup(core, &cx88_sram_channels[SRAM_CH25], 128, 0); - cx88_sram_channel_setup(core, &cx88_sram_channels[SRAM_CH26], 128, 0); + cx88_sram_channel_setup(core, &cx88_sram_channels[SRAM_CH25], bpl, 0); + cx88_sram_channel_setup(core, &cx88_sram_channels[SRAM_CH26], bpl, 0); - cx_write(MO_AUDD_LNGTH, 128); /* fifo bpl size */ - cx_write(MO_AUDR_LNGTH, 128); /* fifo bpl size */ + cx_write(MO_AUDD_LNGTH, bpl); /* fifo bpl size */ + cx_write(MO_AUDR_LNGTH, bpl); /* fifo bpl size */ /* start dma */ cx_write(MO_AUD_DMACNTRL, 0x0003); /* Up and Down fifo enable */ diff --git a/drivers/media/video/cx88/cx88-input.c b/drivers/media/video/cx88/cx88-input.c index da2ad5c4b55..165d948624a 100644 --- a/drivers/media/video/cx88/cx88-input.c +++ b/drivers/media/video/cx88/cx88-input.c @@ -482,6 +482,7 @@ int cx88_ir_init(struct cx88_core *core, struct pci_dev *pci) switch (core->board) { case CX88_BOARD_DNTV_LIVE_DVB_T: case CX88_BOARD_KWORLD_DVB_T: + case CX88_BOARD_KWORLD_DVB_T_CX22702: ir_codes = ir_codes_dntv_live_dvb_t; ir->gpio_addr = MO_GP1_IO; ir->mask_keycode = 0x1f; diff --git a/drivers/media/video/em28xx/em28xx-core.c b/drivers/media/video/em28xx/em28xx-core.c index dff3893f32f..e5ee8bceb21 100644 --- a/drivers/media/video/em28xx/em28xx-core.c +++ b/drivers/media/video/em28xx/em28xx-core.c @@ -139,6 +139,9 @@ int em28xx_read_reg_req_len(struct em28xx *dev, u8 req, u16 reg, { int ret, byte; + if (dev->state & DEV_DISCONNECTED) + return(-ENODEV); + em28xx_regdbg("req=%02x, reg=%02x ", req, reg); ret = usb_control_msg(dev->udev, usb_rcvctrlpipe(dev->udev, 0), req, @@ -165,6 +168,9 @@ int em28xx_read_reg_req(struct em28xx *dev, u8 req, u16 reg) u8 val; int ret; + if (dev->state & DEV_DISCONNECTED) + return(-ENODEV); + em28xx_regdbg("req=%02x, reg=%02x:", req, reg); ret = usb_control_msg(dev->udev, usb_rcvctrlpipe(dev->udev, 0), req, @@ -195,7 +201,12 @@ int em28xx_write_regs_req(struct em28xx *dev, u8 req, u16 reg, char *buf, int ret; /*usb_control_msg seems to expect a kmalloced buffer */ - unsigned char *bufs = kmalloc(len, GFP_KERNEL); + unsigned char *bufs; + + if (dev->state & DEV_DISCONNECTED) + return(-ENODEV); + + bufs = kmalloc(len, GFP_KERNEL); em28xx_regdbg("req=%02x reg=%02x:", req, reg); @@ -212,7 +223,7 @@ int em28xx_write_regs_req(struct em28xx *dev, u8 req, u16 reg, char *buf, ret = usb_control_msg(dev->udev, usb_sndctrlpipe(dev->udev, 0), req, USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE, 0x0000, reg, bufs, len, HZ); - mdelay(5); /* FIXME: magic number */ + msleep(5); /* FIXME: magic number */ kfree(bufs); return ret; } @@ -253,7 +264,7 @@ int em28xx_write_ac97(struct em28xx *dev, u8 reg, u8 * val) if ((ret = em28xx_read_reg(dev, AC97BUSY_REG)) < 0) return ret; else if (((u8) ret) & 0x01) { - em28xx_warn ("AC97 command still being exectuted: not handled properly!\n"); + em28xx_warn ("AC97 command still being executed: not handled properly!\n"); } return 0; } diff --git a/drivers/media/video/em28xx/em28xx-i2c.c b/drivers/media/video/em28xx/em28xx-i2c.c index 0591a705b7a..6ca8631bc36 100644 --- a/drivers/media/video/em28xx/em28xx-i2c.c +++ b/drivers/media/video/em28xx/em28xx-i2c.c @@ -78,7 +78,7 @@ static int em2800_i2c_send_max4(struct em28xx *dev, unsigned char addr, ret = dev->em28xx_read_reg(dev, 0x05); if (ret == 0x80 + len - 1) return len; - mdelay(5); + msleep(5); } em28xx_warn("i2c write timed out\n"); return -EIO; @@ -138,7 +138,7 @@ static int em2800_i2c_check_for_device(struct em28xx *dev, unsigned char addr) return -ENODEV; else if (msg == 0x84) return 0; - mdelay(5); + msleep(5); } return -ENODEV; } @@ -278,9 +278,9 @@ static int em28xx_i2c_xfer(struct i2c_adapter *i2c_adap, msgs[i].buf, msgs[i].len, i == num - 1); - if (rc < 0) - goto err; } + if (rc < 0) + goto err; if (i2c_debug>=2) printk("\n"); } diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c index eea304f7517..94a14a2bb6d 100644 --- a/drivers/media/video/em28xx/em28xx-video.c +++ b/drivers/media/video/em28xx/em28xx-video.c @@ -6,6 +6,9 @@ Mauro Carvalho Chehab <mchehab@brturbo.com.br> Sascha Sommer <saschasommer@freenet.de> + Some parts based on SN9C10x PC Camera Controllers GPL driver made + by Luca Risolia <luca.risolia@studio.unibo.it> + This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or diff --git a/drivers/media/video/saa7134/saa7134-cards.c b/drivers/media/video/saa7134/saa7134-cards.c index c64718aec9c..5a35d3b6550 100644 --- a/drivers/media/video/saa7134/saa7134-cards.c +++ b/drivers/media/video/saa7134/saa7134-cards.c @@ -136,7 +136,7 @@ struct saa7134_board saa7134_boards[] = { }, [SAA7134_BOARD_FLYVIDEO2000] = { /* "TC Wan" <tcwan@cs.usm.my> */ - .name = "LifeView FlyVIDEO2000", + .name = "LifeView/Typhoon FlyVIDEO2000", .audio_clock = 0x00200000, .tuner_type = TUNER_LG_PAL_NEW_TAPC, .radio_type = UNSET, @@ -1884,44 +1884,38 @@ struct saa7134_board saa7134_boards[] = { .gpio = 0x000, }, }, - [SAA7134_BOARD_THYPHOON_DVBT_DUO_CARDBUS] = { - .name = "Typhoon DVB-T Duo Digital/Analog Cardbus", + [SAA7134_BOARD_FLYDVBT_DUO_CARDBUS] = { + .name = "LifeView/Typhoon FlyDVB-T Duo Cardbus", .audio_clock = 0x00200000, .tuner_type = TUNER_PHILIPS_TDA8290, .radio_type = UNSET, .tuner_addr = ADDR_UNSET, .radio_addr = ADDR_UNSET, .mpeg = SAA7134_MPEG_DVB, - /* .gpiomask = 0xe000, */ + .gpiomask = 0x00200000, .inputs = {{ .name = name_tv, .vmux = 1, .amux = TV, - /* .gpio = 0x0000, */ + .gpio = 0x200000, /* GPIO21=High for TV input */ .tv = 1, },{ + .name = name_svideo, /* S-Video signal on S-Video input */ + .vmux = 8, + .amux = LINE2, + },{ .name = name_comp1, /* Composite signal on S-Video input */ .vmux = 0, .amux = LINE2, - /* .gpio = 0x4000, */ },{ .name = name_comp2, /* Composite input */ .vmux = 3, .amux = LINE2, - /* .gpio = 0x4000, */ - },{ - .name = name_svideo, /* S-Video signal on S-Video input */ - .vmux = 8, - .amux = LINE2, - /* .gpio = 0x4000, */ }}, .radio = { .name = name_radio, - .amux = LINE2, - }, - .mute = { - .name = name_mute, - .amux = LINE1, + .amux = TV, + .gpio = 0x000000, /* GPIO21=Low for FM radio antenna */ }, }, [SAA7134_BOARD_VIDEOMATE_TV_GOLD_PLUSII] = { @@ -2701,6 +2695,12 @@ struct pci_device_id saa7134_pci_tbl[] = { .driver_data = SAA7134_BOARD_FLYVIDEO2000, },{ .vendor = PCI_VENDOR_ID_PHILIPS, + .device = PCI_DEVICE_ID_PHILIPS_SAA7130, + .subvendor = 0x4e42, /* Typhoon */ + .subdevice = 0x0138, /* LifeView FlyTV Prime30 OEM */ + .driver_data = SAA7134_BOARD_FLYVIDEO2000, + },{ + .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, .subvendor = 0x5168, .subdevice = 0x0212, /* minipci, LR212 */ @@ -2935,7 +2935,7 @@ struct pci_device_id saa7134_pci_tbl[] = { .device = PCI_DEVICE_ID_PHILIPS_SAA7133, .subvendor = 0x5168, .subdevice = 0x0502, /* Cardbus version */ - .driver_data = SAA7134_BOARD_FLYDVBTDUO, + .driver_data = SAA7134_BOARD_FLYDVBT_DUO_CARDBUS, },{ .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, @@ -2980,12 +2980,12 @@ struct pci_device_id saa7134_pci_tbl[] = { .subdevice = 0x1370, /* cardbus version */ .driver_data = SAA7134_BOARD_ADS_INSTANT_TV, - },{ /* Typhoon DVB-T Duo Digital/Analog Cardbus */ + },{ .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, - .subvendor = 0x4e42, - .subdevice = 0x0502, - .driver_data = SAA7134_BOARD_THYPHOON_DVBT_DUO_CARDBUS, + .subvendor = 0x4e42, /* Typhoon */ + .subdevice = 0x0502, /* LifeView LR502 OEM */ + .driver_data = SAA7134_BOARD_FLYDVBT_DUO_CARDBUS, },{ .vendor = PCI_VENDOR_ID_PHILIPS, .device = PCI_DEVICE_ID_PHILIPS_SAA7133, @@ -3206,8 +3206,7 @@ int saa7134_board_init1(struct saa7134_dev *dev) saa_andorl(SAA7134_GPIO_GPMODE0 >> 2, 0x00040000, 0x00040000); saa_andorl(SAA7134_GPIO_GPSTATUS0 >> 2, 0x00040000, 0x00000004); break; - case SAA7134_BOARD_FLYDVBTDUO: - case SAA7134_BOARD_THYPHOON_DVBT_DUO_CARDBUS: + case SAA7134_BOARD_FLYDVBT_DUO_CARDBUS: /* turn the fan on */ saa_writeb(SAA7134_GPIO_GPMODE3, 0x08); saa_writeb(SAA7134_GPIO_GPSTATUS3, 0x06); diff --git a/drivers/media/video/saa7134/saa7134-dvb.c b/drivers/media/video/saa7134/saa7134-dvb.c index 399f9952596..1a536e86527 100644 --- a/drivers/media/video/saa7134/saa7134-dvb.c +++ b/drivers/media/video/saa7134/saa7134-dvb.c @@ -861,7 +861,7 @@ static int dvb_init(struct saa7134_dev *dev) dev->dvb.frontend = tda10046_attach(&tda827x_lifeview_config, &dev->i2c_adap); break; - case SAA7134_BOARD_THYPHOON_DVBT_DUO_CARDBUS: + case SAA7134_BOARD_FLYDVBT_DUO_CARDBUS: dev->dvb.frontend = tda10046_attach(&tda827x_lifeview_config, &dev->i2c_adap); break; diff --git a/drivers/media/video/saa7134/saa7134.h b/drivers/media/video/saa7134/saa7134.h index e70eae8d29b..3261d8bebdd 100644 --- a/drivers/media/video/saa7134/saa7134.h +++ b/drivers/media/video/saa7134/saa7134.h @@ -185,7 +185,7 @@ struct saa7134_format { #define SAA7134_BOARD_AVERMEDIA_GO_007_FM 57 #define SAA7134_BOARD_ADS_INSTANT_TV 58 #define SAA7134_BOARD_KWORLD_VSTREAM_XPERT 59 -#define SAA7134_BOARD_THYPHOON_DVBT_DUO_CARDBUS 60 +#define SAA7134_BOARD_FLYDVBT_DUO_CARDBUS 60 #define SAA7134_BOARD_PHILIPS_TOUGH 61 #define SAA7134_BOARD_VIDEOMATE_TV_GOLD_PLUSII 62 #define SAA7134_BOARD_KWORLD_XPERT 63 diff --git a/drivers/media/video/stradis.c b/drivers/media/video/stradis.c index 54fc33011ff..9d769264a32 100644 --- a/drivers/media/video/stradis.c +++ b/drivers/media/video/stradis.c @@ -2012,7 +2012,6 @@ static int __devinit init_saa7146(struct pci_dev *pdev) { struct saa7146 *saa = pci_get_drvdata(pdev); - memset(saa, 0, sizeof(*saa)); saa->user = 0; /* reset the saa7146 */ saawrite(0xffff0000, SAA7146_MC1); @@ -2062,16 +2061,16 @@ static int __devinit init_saa7146(struct pci_dev *pdev) } if (saa->audbuf == NULL && (saa->audbuf = vmalloc(65536)) == NULL) { dev_err(&pdev->dev, "%d: malloc failed\n", saa->nr); - goto errvid; + goto errfree; } if (saa->osdbuf == NULL && (saa->osdbuf = vmalloc(131072)) == NULL) { dev_err(&pdev->dev, "%d: malloc failed\n", saa->nr); - goto erraud; + goto errfree; } /* allocate 81920 byte buffer for clipping */ if ((saa->dmavid2 = kzalloc(VIDEO_CLIPMAP_SIZE, GFP_KERNEL)) == NULL) { dev_err(&pdev->dev, "%d: clip kmalloc failed\n", saa->nr); - goto errosd; + goto errfree; } /* setup clipping registers */ saawrite(virt_to_bus(saa->dmavid2), SAA7146_BASE_EVEN2); @@ -2085,15 +2084,11 @@ static int __devinit init_saa7146(struct pci_dev *pdev) I2CBusScan(saa); return 0; -errosd: +errfree: vfree(saa->osdbuf); - saa->osdbuf = NULL; -erraud: vfree(saa->audbuf); - saa->audbuf = NULL; -errvid: vfree(saa->vidbuf); - saa->vidbuf = NULL; + saa->audbuf = saa->osdbuf = saa->vidbuf = NULL; err: return -ENOMEM; } diff --git a/drivers/media/video/tda9887.c b/drivers/media/video/tda9887.c index 5815649bdc7..0d54f6c1982 100644 --- a/drivers/media/video/tda9887.c +++ b/drivers/media/video/tda9887.c @@ -231,7 +231,7 @@ static struct tvnorm tvnorms[] = { cAudioIF_6_5 | cVideoIF_38_90 ), },{ - .std = V4L2_STD_NTSC_M, + .std = V4L2_STD_NTSC_M | V4L2_STD_NTSC_M_KR, .name = "NTSC-M", .b = ( cNegativeFmTV | cQSS ), @@ -619,6 +619,11 @@ static int tda9887_fixup_std(struct tda9887 *t) tda9887_dbg("insmod fixup: NTSC => NTSC_M_JP\n"); t->std = V4L2_STD_NTSC_M_JP; break; + case 'k': + case 'K': + tda9887_dbg("insmod fixup: NTSC => NTSC_M_KR\n"); + t->std = V4L2_STD_NTSC_M_KR; + break; case '-': /* default parameter, do nothing */ break; @@ -876,7 +881,7 @@ static int tda9887_resume(struct device * dev) /* ----------------------------------------------------------------------- */ static struct i2c_driver driver = { - .id = -1, /* FIXME */ + .id = I2C_DRIVERID_TDA9887, .attach_adapter = tda9887_probe, .detach_client = tda9887_detach, .command = tda9887_command, diff --git a/drivers/media/video/tuner-core.c b/drivers/media/video/tuner-core.c index 2995b22acb4..e7ee619d62c 100644 --- a/drivers/media/video/tuner-core.c +++ b/drivers/media/video/tuner-core.c @@ -216,6 +216,7 @@ static void set_type(struct i2c_client *c, unsigned int type, buffer[3] = 0xa4; i2c_master_send(c,buffer,4); default_tuner_init(c); + break; default: default_tuner_init(c); break; @@ -365,6 +366,11 @@ static int tuner_fixup_std(struct tuner *t) tuner_dbg("insmod fixup: NTSC => NTSC_M_JP\n"); t->std = V4L2_STD_NTSC_M_JP; break; + case 'k': + case 'K': + tuner_dbg("insmod fixup: NTSC => NTSC_M_KR\n"); + t->std = V4L2_STD_NTSC_M_KR; + break; case '-': /* default parameter, do nothing */ break; @@ -448,7 +454,7 @@ static int tuner_attach(struct i2c_adapter *adap, int addr, int kind) printk("%02x ",buffer[i]); printk("\n"); } - /* TEA5767 autodetection code - only for addr = 0xc0 */ + /* autodetection code based on the i2c addr */ if (!no_autodetect) { switch (addr) { case 0x42: diff --git a/drivers/media/video/tvaudio.c b/drivers/media/video/tvaudio.c index 6d03b9b05c6..c8e5ad0e818 100644 --- a/drivers/media/video/tvaudio.c +++ b/drivers/media/video/tvaudio.c @@ -390,6 +390,14 @@ static void tda9840_setmode(struct CHIPSTATE *chip, int mode) chip_write(chip, TDA9840_SW, t); } +static int tda9840_checkit(struct CHIPSTATE *chip) +{ + int rc; + rc = chip_read(chip); + /* lower 5 bits should be 0 */ + return ((rc & 0x1f) == 0) ? 1 : 0; +} + /* ---------------------------------------------------------------------- */ /* audio chip descriptions - defines+functions for tda985x */ @@ -1264,6 +1272,7 @@ static struct CHIPDESC chiplist[] = { .addr_hi = I2C_TDA9840 >> 1, .registers = 5, + .checkit = tda9840_checkit, .getmode = tda9840_getmode, .setmode = tda9840_setmode, .checkmode = generic_checkmode, diff --git a/drivers/media/video/tvp5150.c b/drivers/media/video/tvp5150.c index fad9ea0ae4f..1864423b304 100644 --- a/drivers/media/video/tvp5150.c +++ b/drivers/media/video/tvp5150.c @@ -746,24 +746,27 @@ static int tvp5150_set_std(struct i2c_client *c, v4l2_std_id std) static inline void tvp5150_reset(struct i2c_client *c) { - u8 type, ver_656, msb_id, lsb_id, msb_rom, lsb_rom; + u8 msb_id, lsb_id, msb_rom, lsb_rom; struct tvp5150 *decoder = i2c_get_clientdata(c); - type=tvp5150_read(c,TVP5150_AUTOSW_MSK); msb_id=tvp5150_read(c,TVP5150_MSB_DEV_ID); lsb_id=tvp5150_read(c,TVP5150_LSB_DEV_ID); msb_rom=tvp5150_read(c,TVP5150_ROM_MAJOR_VER); lsb_rom=tvp5150_read(c,TVP5150_ROM_MINOR_VER); - if (type==0xdc) { - ver_656=tvp5150_read(c,TVP5150_REV_SELECT); - tvp5150_info("tvp%02x%02xam1 detected 656 version is %d.\n",msb_id, lsb_id,ver_656); - } else if (type==0xfc) { - tvp5150_info("tvp%02x%02xa detected.\n",msb_id, lsb_id); + if ((msb_rom==4)&&(lsb_rom==0)) { /* Is TVP5150AM1 */ + tvp5150_info("tvp%02x%02xam1 detected.\n",msb_id, lsb_id); + + /* ITU-T BT.656.4 timing */ + tvp5150_write(c,TVP5150_REV_SELECT,0); } else { - tvp5150_info("unknown tvp%02x%02x chip detected(%d).\n",msb_id,lsb_id,type); + if ((msb_rom==3)||(lsb_rom==0x21)) { /* Is TVP5150A */ + tvp5150_info("tvp%02x%02xa detected.\n",msb_id, lsb_id); + } else { + tvp5150_info("*** unknown tvp%02x%02x chip detected.\n",msb_id,lsb_id); + tvp5150_info("*** Rom ver is %d.%d\n",msb_rom,lsb_rom); + } } - tvp5150_info("Rom ver is %d.%d\n",msb_rom,lsb_rom); /* Initializes TVP5150 to its default values */ tvp5150_write_inittab(c, tvp5150_init_default); @@ -893,6 +896,17 @@ static int tvp5150_command(struct i2c_client *c, } case DECODER_GET_STATUS: { + int *iarg = arg; + int status; + int res=0; + status = tvp5150_read(c, 0x88); + if(status&0x08){ + res |= DECODER_STATUS_COLOR; + } + if(status&0x04 && status&0x02){ + res |= DECODER_STATUS_GOOD; + } + *iarg=res; break; } diff --git a/drivers/net/8139too.c b/drivers/net/8139too.c index adfba44dac5..2beac55b57d 100644 --- a/drivers/net/8139too.c +++ b/drivers/net/8139too.c @@ -586,6 +586,7 @@ struct rtl8139_private { dma_addr_t tx_bufs_dma; signed char phys[4]; /* MII device addresses. */ char twistie, twist_row, twist_col; /* Twister tune state. */ + unsigned int watchdog_fired : 1; unsigned int default_port : 4; /* Last dev->if_port value. */ unsigned int have_thread : 1; spinlock_t lock; @@ -638,6 +639,7 @@ static void rtl8139_set_rx_mode (struct net_device *dev); static void __set_rx_mode (struct net_device *dev); static void rtl8139_hw_start (struct net_device *dev); static void rtl8139_thread (void *_data); +static void rtl8139_tx_timeout_task(void *_data); static struct ethtool_ops rtl8139_ethtool_ops; /* write MMIO register, with flush */ @@ -1598,13 +1600,14 @@ static void rtl8139_thread (void *_data) { struct net_device *dev = _data; struct rtl8139_private *tp = netdev_priv(dev); - unsigned long thr_delay; + unsigned long thr_delay = next_tick; - if (rtnl_shlock_nowait() == 0) { + if (tp->watchdog_fired) { + tp->watchdog_fired = 0; + rtl8139_tx_timeout_task(_data); + } else if (rtnl_shlock_nowait() == 0) { rtl8139_thread_iter (dev, tp, tp->mmio_addr); rtnl_unlock (); - - thr_delay = next_tick; } else { /* unlikely race. mitigate with fast poll. */ thr_delay = HZ / 2; @@ -1631,7 +1634,8 @@ static void rtl8139_stop_thread(struct rtl8139_private *tp) if (tp->have_thread) { cancel_rearming_delayed_work(&tp->thread); tp->have_thread = 0; - } + } else + flush_scheduled_work(); } static inline void rtl8139_tx_clear (struct rtl8139_private *tp) @@ -1642,14 +1646,13 @@ static inline void rtl8139_tx_clear (struct rtl8139_private *tp) /* XXX account for unsent Tx packets in tp->stats.tx_dropped */ } - -static void rtl8139_tx_timeout (struct net_device *dev) +static void rtl8139_tx_timeout_task (void *_data) { + struct net_device *dev = _data; struct rtl8139_private *tp = netdev_priv(dev); void __iomem *ioaddr = tp->mmio_addr; int i; u8 tmp8; - unsigned long flags; printk (KERN_DEBUG "%s: Transmit timeout, status %2.2x %4.4x %4.4x " "media %2.2x.\n", dev->name, RTL_R8 (ChipCmd), @@ -1670,23 +1673,34 @@ static void rtl8139_tx_timeout (struct net_device *dev) if (tmp8 & CmdTxEnb) RTL_W8 (ChipCmd, CmdRxEnb); - spin_lock(&tp->rx_lock); + spin_lock_bh(&tp->rx_lock); /* Disable interrupts by clearing the interrupt mask. */ RTL_W16 (IntrMask, 0x0000); /* Stop a shared interrupt from scavenging while we are. */ - spin_lock_irqsave (&tp->lock, flags); + spin_lock_irq(&tp->lock); rtl8139_tx_clear (tp); - spin_unlock_irqrestore (&tp->lock, flags); + spin_unlock_irq(&tp->lock); /* ...and finally, reset everything */ if (netif_running(dev)) { rtl8139_hw_start (dev); netif_wake_queue (dev); } - spin_unlock(&tp->rx_lock); + spin_unlock_bh(&tp->rx_lock); } +static void rtl8139_tx_timeout (struct net_device *dev) +{ + struct rtl8139_private *tp = netdev_priv(dev); + + if (!tp->have_thread) { + INIT_WORK(&tp->thread, rtl8139_tx_timeout_task, dev); + schedule_delayed_work(&tp->thread, next_tick); + } else + tp->watchdog_fired = 1; + +} static int rtl8139_start_xmit (struct sk_buff *skb, struct net_device *dev) { diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 6a6a0844180..47c72a63dfe 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -4,9 +4,9 @@ # menu "Network device support" + depends on NET config NETDEVICES - depends on NET default y if UML bool "Network device support" ---help--- @@ -24,9 +24,6 @@ config NETDEVICES If unsure, say Y. -# All the following symbols are dependent on NETDEVICES - do not repeat -# that for each of the symbols. -if NETDEVICES config IFB tristate "Intermediate Functional Block support" @@ -2718,8 +2715,6 @@ config NETCONSOLE If you want to log kernel messages over the network, enable this. See <file:Documentation/networking/netconsole.txt> for details. -endif #NETDEVICES - config NETPOLL def_bool NETCONSOLE diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index 4ff006c3762..e0f51afec77 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -1145,7 +1145,8 @@ int bond_sethwaddr(struct net_device *bond_dev, struct net_device *slave_dev) } #define BOND_INTERSECT_FEATURES \ - (NETIF_F_SG|NETIF_F_IP_CSUM|NETIF_F_NO_CSUM|NETIF_F_HW_CSUM) + (NETIF_F_SG|NETIF_F_IP_CSUM|NETIF_F_NO_CSUM|NETIF_F_HW_CSUM|\ + NETIF_F_TSO|NETIF_F_UFO) /* * Compute the common dev->feature set available to all slaves. Some @@ -1168,6 +1169,16 @@ static int bond_compute_features(struct bonding *bond) NETIF_F_HW_CSUM))) features &= ~NETIF_F_SG; + /* + * features will include NETIF_F_TSO (NETIF_F_UFO) iff all + * slave devices support NETIF_F_TSO (NETIF_F_UFO), which + * implies that all slaves also support scatter-gather + * (NETIF_F_SG), which implies that features also includes + * NETIF_F_SG. So no need to check whether we have an + * illegal combination of NETIF_F_{TSO,UFO} and + * !NETIF_F_SG + */ + features |= (bond_dev->features & ~BOND_INTERSECT_FEATURES); bond_dev->features = features; @@ -4080,6 +4091,8 @@ static void bond_ethtool_get_drvinfo(struct net_device *bond_dev, static struct ethtool_ops bond_ethtool_ops = { .get_tx_csum = ethtool_op_get_tx_csum, + .get_tso = ethtool_op_get_tso, + .get_ufo = ethtool_op_get_ufo, .get_sg = ethtool_op_get_sg, .get_drvinfo = bond_ethtool_get_drvinfo, }; diff --git a/drivers/net/bonding/bond_sysfs.c b/drivers/net/bonding/bond_sysfs.c index 32d13da43a0..041bcc58355 100644 --- a/drivers/net/bonding/bond_sysfs.c +++ b/drivers/net/bonding/bond_sysfs.c @@ -260,7 +260,7 @@ static ssize_t bonding_store_slaves(struct class_device *cd, const char *buffer, char *ifname; int i, res, found, ret = count; struct slave *slave; - struct net_device *dev = 0; + struct net_device *dev = NULL; struct bonding *bond = to_bond(cd); /* Quick sanity check -- is the bond interface up? */ @@ -995,7 +995,7 @@ static ssize_t bonding_store_primary(struct class_device *cd, const char *buf, s printk(KERN_INFO DRV_NAME ": %s: Setting primary slave to None.\n", bond->dev->name); - bond->primary_slave = 0; + bond->primary_slave = NULL; bond_select_active_slave(bond); } else { printk(KERN_INFO DRV_NAME @@ -1123,7 +1123,7 @@ static ssize_t bonding_store_active_slave(struct class_device *cd, const char *b printk(KERN_INFO DRV_NAME ": %s: Setting active slave to None.\n", bond->dev->name); - bond->primary_slave = 0; + bond->primary_slave = NULL; bond_select_active_slave(bond); } else { printk(KERN_INFO DRV_NAME diff --git a/drivers/net/e100.c b/drivers/net/e100.c index bf1fd2b98bf..24253c807e5 100644 --- a/drivers/net/e100.c +++ b/drivers/net/e100.c @@ -2752,8 +2752,6 @@ static int e100_resume(struct pci_dev *pdev) retval = pci_enable_wake(pdev, 0, 0); if (retval) DPRINTK(PROBE,ERR, "Error clearing wake events\n"); - if(e100_hw_init(nic)) - DPRINTK(HW, ERR, "e100_hw_init failed\n"); netif_device_attach(netdev); if(netif_running(netdev)) diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c index 0c18dbd67d3..0e8e3fcde9f 100644 --- a/drivers/net/gianfar.c +++ b/drivers/net/gianfar.c @@ -199,8 +199,7 @@ static int gfar_probe(struct platform_device *pdev) /* get a pointer to the register memory */ r = platform_get_resource(pdev, IORESOURCE_MEM, 0); - priv->regs = (struct gfar *) - ioremap(r->start, sizeof (struct gfar)); + priv->regs = ioremap(r->start, sizeof (struct gfar)); if (NULL == priv->regs) { err = -ENOMEM; @@ -369,7 +368,7 @@ static int gfar_probe(struct platform_device *pdev) return 0; register_fail: - iounmap((void *) priv->regs); + iounmap(priv->regs); regs_fail: free_netdev(dev); return err; @@ -382,7 +381,7 @@ static int gfar_remove(struct platform_device *pdev) platform_set_drvdata(pdev, NULL); - iounmap((void *) priv->regs); + iounmap(priv->regs); free_netdev(dev); return 0; @@ -454,8 +453,7 @@ static void init_registers(struct net_device *dev) /* Zero out the rmon mib registers if it has them */ if (priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_RMON) { - memset((void *) &(priv->regs->rmon), 0, - sizeof (struct rmon_mib)); + memset_io(&(priv->regs->rmon), 0, sizeof (struct rmon_mib)); /* Mask off the CAM interrupts */ gfar_write(&priv->regs->rmon.cam1, 0xffffffff); @@ -477,7 +475,7 @@ static void init_registers(struct net_device *dev) void gfar_halt(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); - struct gfar *regs = priv->regs; + struct gfar __iomem *regs = priv->regs; u32 tempval; /* Mask all interrupts */ @@ -507,7 +505,7 @@ void gfar_halt(struct net_device *dev) void stop_gfar(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); - struct gfar *regs = priv->regs; + struct gfar __iomem *regs = priv->regs; unsigned long flags; phy_stop(priv->phydev); @@ -590,7 +588,7 @@ static void free_skb_resources(struct gfar_private *priv) void gfar_start(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); - struct gfar *regs = priv->regs; + struct gfar __iomem *regs = priv->regs; u32 tempval; /* Enable Rx and Tx in MACCFG1 */ @@ -624,7 +622,7 @@ int startup_gfar(struct net_device *dev) unsigned long vaddr; int i; struct gfar_private *priv = netdev_priv(dev); - struct gfar *regs = priv->regs; + struct gfar __iomem *regs = priv->regs; int err = 0; u32 rctrl = 0; u32 attrs = 0; @@ -1622,7 +1620,7 @@ static irqreturn_t gfar_interrupt(int irq, void *dev_id, struct pt_regs *regs) static void adjust_link(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); - struct gfar *regs = priv->regs; + struct gfar __iomem *regs = priv->regs; unsigned long flags; struct phy_device *phydev = priv->phydev; int new_state = 0; @@ -1703,7 +1701,7 @@ static void gfar_set_multi(struct net_device *dev) { struct dev_mc_list *mc_ptr; struct gfar_private *priv = netdev_priv(dev); - struct gfar *regs = priv->regs; + struct gfar __iomem *regs = priv->regs; u32 tempval; if(dev->flags & IFF_PROMISC) { @@ -1842,7 +1840,7 @@ static void gfar_set_mac_for_addr(struct net_device *dev, int num, u8 *addr) int idx; char tmpbuf[MAC_ADDR_LEN]; u32 tempval; - u32 *macptr = &priv->regs->macstnaddr1; + u32 __iomem *macptr = &priv->regs->macstnaddr1; macptr += num*2; diff --git a/drivers/net/gianfar.h b/drivers/net/gianfar.h index cb9d66ac3ab..d37d5401be6 100644 --- a/drivers/net/gianfar.h +++ b/drivers/net/gianfar.h @@ -682,8 +682,8 @@ struct gfar_private { struct rxbd8 *cur_rx; /* Next free rx ring entry */ struct txbd8 *cur_tx; /* Next free ring entry */ struct txbd8 *dirty_tx; /* The Ring entry to be freed. */ - struct gfar *regs; /* Pointer to the GFAR memory mapped Registers */ - u32 *hash_regs[16]; + struct gfar __iomem *regs; /* Pointer to the GFAR memory mapped Registers */ + u32 __iomem *hash_regs[16]; int hash_width; struct net_device_stats stats; /* linux network statistics */ struct gfar_extra_stats extra_stats; @@ -718,14 +718,14 @@ struct gfar_private { uint32_t msg_enable; }; -static inline u32 gfar_read(volatile unsigned *addr) +static inline u32 gfar_read(volatile unsigned __iomem *addr) { u32 val; val = in_be32(addr); return val; } -static inline void gfar_write(volatile unsigned *addr, u32 val) +static inline void gfar_write(volatile unsigned __iomem *addr, u32 val) { out_be32(addr, val); } diff --git a/drivers/net/gianfar_ethtool.c b/drivers/net/gianfar_ethtool.c index 765e810620f..5de7b2e259d 100644 --- a/drivers/net/gianfar_ethtool.c +++ b/drivers/net/gianfar_ethtool.c @@ -144,11 +144,11 @@ static void gfar_fill_stats(struct net_device *dev, struct ethtool_stats *dummy, u64 *extra = (u64 *) & priv->extra_stats; if (priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_RMON) { - u32 *rmon = (u32 *) & priv->regs->rmon; + u32 __iomem *rmon = (u32 __iomem *) & priv->regs->rmon; struct gfar_stats *stats = (struct gfar_stats *) buf; for (i = 0; i < GFAR_RMON_LEN; i++) - stats->rmon[i] = (u64) (rmon[i]); + stats->rmon[i] = (u64) gfar_read(&rmon[i]); for (i = 0; i < GFAR_EXTRA_STATS_LEN; i++) stats->extra[i] = extra[i]; @@ -221,11 +221,11 @@ static void gfar_get_regs(struct net_device *dev, struct ethtool_regs *regs, voi { int i; struct gfar_private *priv = netdev_priv(dev); - u32 *theregs = (u32 *) priv->regs; + u32 __iomem *theregs = (u32 __iomem *) priv->regs; u32 *buf = (u32 *) regbuf; for (i = 0; i < sizeof (struct gfar) / sizeof (u32); i++) - buf[i] = theregs[i]; + buf[i] = gfar_read(&theregs[i]); } /* Convert microseconds to ethernet clock ticks, which changes diff --git a/drivers/net/gianfar_mii.c b/drivers/net/gianfar_mii.c index 74e52fcbf80..c6b725529af 100644 --- a/drivers/net/gianfar_mii.c +++ b/drivers/net/gianfar_mii.c @@ -50,7 +50,7 @@ * All PHY configuration is done through the TSEC1 MIIM regs */ int gfar_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value) { - struct gfar_mii *regs = bus->priv; + struct gfar_mii __iomem *regs = (void __iomem *)bus->priv; /* Set the PHY address and the register address we want to write */ gfar_write(®s->miimadd, (mii_id << 8) | regnum); @@ -70,7 +70,7 @@ int gfar_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value) * configuration has to be done through the TSEC1 MIIM regs */ int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum) { - struct gfar_mii *regs = bus->priv; + struct gfar_mii __iomem *regs = (void __iomem *)bus->priv; u16 value; /* Set the PHY address and the register address we want to read */ @@ -94,7 +94,7 @@ int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum) /* Reset the MIIM registers, and wait for the bus to free */ int gfar_mdio_reset(struct mii_bus *bus) { - struct gfar_mii *regs = bus->priv; + struct gfar_mii __iomem *regs = (void __iomem *)bus->priv; unsigned int timeout = PHY_INIT_TIMEOUT; spin_lock_bh(&bus->mdio_lock); @@ -126,7 +126,7 @@ int gfar_mdio_probe(struct device *dev) { struct platform_device *pdev = to_platform_device(dev); struct gianfar_mdio_data *pdata; - struct gfar_mii *regs; + struct gfar_mii __iomem *regs; struct mii_bus *new_bus; struct resource *r; int err = 0; @@ -155,15 +155,14 @@ int gfar_mdio_probe(struct device *dev) r = platform_get_resource(pdev, IORESOURCE_MEM, 0); /* Set the PHY base address */ - regs = (struct gfar_mii *) ioremap(r->start, - sizeof (struct gfar_mii)); + regs = ioremap(r->start, sizeof (struct gfar_mii)); if (NULL == regs) { err = -ENOMEM; goto reg_map_fail; } - new_bus->priv = regs; + new_bus->priv = (void __force *)regs; new_bus->irq = pdata->irq; @@ -181,7 +180,7 @@ int gfar_mdio_probe(struct device *dev) return 0; bus_register_fail: - iounmap((void *) regs); + iounmap(regs); reg_map_fail: kfree(new_bus); @@ -197,7 +196,7 @@ int gfar_mdio_remove(struct device *dev) dev_set_drvdata(dev, NULL); - iounmap((void *) (&bus->priv)); + iounmap((void __iomem *)bus->priv); bus->priv = NULL; kfree(bus); diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c index 2e1bed153c3..6e1018448ee 100644 --- a/drivers/net/r8169.c +++ b/drivers/net/r8169.c @@ -484,13 +484,12 @@ static void mdio_write(void __iomem *ioaddr, int RegAddr, int value) int i; RTL_W32(PHYAR, 0x80000000 | (RegAddr & 0xFF) << 16 | value); - udelay(1000); - for (i = 2000; i > 0; i--) { + for (i = 20; i > 0; i--) { /* Check if the RTL8169 has completed writing to the specified MII register */ if (!(RTL_R32(PHYAR) & 0x80000000)) break; - udelay(100); + udelay(25); } } @@ -499,15 +498,14 @@ static int mdio_read(void __iomem *ioaddr, int RegAddr) int i, value = -1; RTL_W32(PHYAR, 0x0 | (RegAddr & 0xFF) << 16); - udelay(1000); - for (i = 2000; i > 0; i--) { + for (i = 20; i > 0; i--) { /* Check if the RTL8169 has completed retrieving data from the specified MII register */ if (RTL_R32(PHYAR) & 0x80000000) { value = (int) (RTL_R32(PHYAR) & 0xFFFF); break; } - udelay(100); + udelay(25); } return value; } @@ -677,6 +675,9 @@ static int rtl8169_set_speed_xmii(struct net_device *dev, if (duplex == DUPLEX_HALF) auto_nego &= ~(PHY_Cap_10_Full | PHY_Cap_100_Full); + + if (duplex == DUPLEX_FULL) + auto_nego &= ~(PHY_Cap_10_Half | PHY_Cap_100_Half); } tp->phy_auto_nego_reg = auto_nego; diff --git a/drivers/net/sis900.h b/drivers/net/sis900.h index 4233ea55670..50323941e3c 100644 --- a/drivers/net/sis900.h +++ b/drivers/net/sis900.h @@ -33,7 +33,6 @@ enum sis900_registers { rxcfg=0x34, //Receive Configuration Register flctrl=0x38, //Flow Control Register rxlen=0x3c, //Receive Packet Length Register - cfgpmcsr=0x44, //Configuration Power Management Control/Status Register rfcr=0x48, //Receive Filter Control Register rfdr=0x4C, //Receive Filter Data Register pmctrl=0xB0, //Power Management Control Register diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index f8b973a04b6..cae2edf2300 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -23,12 +23,6 @@ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ -/* - * TOTEST - * - speed setting - * - suspend/resume - */ - #include <linux/config.h> #include <linux/crc32.h> #include <linux/kernel.h> @@ -57,7 +51,7 @@ #include "sky2.h" #define DRV_NAME "sky2" -#define DRV_VERSION "0.13" +#define DRV_VERSION "0.15" #define PFX DRV_NAME " " /* @@ -102,6 +96,10 @@ static int copybreak __read_mostly = 256; module_param(copybreak, int, 0); MODULE_PARM_DESC(copybreak, "Receive copy threshold"); +static int disable_msi = 0; +module_param(disable_msi, int, 0); +MODULE_PARM_DESC(disable_msi, "Disable Message Signaled Interrupt (MSI)"); + static const struct pci_device_id sky2_id_table[] = { { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) }, { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) }, @@ -198,7 +196,7 @@ static int sky2_set_power_state(struct sky2_hw *hw, pci_power_t state) sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_PMC, &power_control); - vaux = (sky2_read8(hw, B0_CTST) & Y2_VAUX_AVAIL) && + vaux = (sky2_read16(hw, B0_CTST) & Y2_VAUX_AVAIL) && (power_control & PCI_PM_CAP_PME_D3cold); pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_CTRL, &power_control); @@ -1834,6 +1832,8 @@ static int sky2_poll(struct net_device *dev0, int *budget) u16 hwidx; u16 tx_done[2] = { TX_NO_STATUS, TX_NO_STATUS }; + sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ); + hwidx = sky2_read16(hw, STAT_PUT_IDX); BUG_ON(hwidx >= STATUS_RING_SIZE); rmb(); @@ -1913,12 +1913,10 @@ static int sky2_poll(struct net_device *dev0, int *budget) } exit_loop: - sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ); - sky2_tx_check(hw, 0, tx_done[0]); sky2_tx_check(hw, 1, tx_done[1]); - if (sky2_read16(hw, STAT_PUT_IDX) == hw->st_idx) { + if (likely(work_done < to_do)) { /* need to restart TX timer */ if (is_ec_a1(hw)) { sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP); @@ -2141,14 +2139,12 @@ static inline u32 sky2_clk2us(const struct sky2_hw *hw, u32 clk) static int sky2_reset(struct sky2_hw *hw) { - u32 ctst; u16 status; u8 t8, pmd_type; - int i; - - ctst = sky2_read32(hw, B0_CTST); + int i, err; sky2_write8(hw, B0_CTST, CS_RST_CLR); + hw->chip_id = sky2_read8(hw, B2_CHIP_ID); if (hw->chip_id < CHIP_ID_YUKON_XL || hw->chip_id > CHIP_ID_YUKON_FE) { printk(KERN_ERR PFX "%s: unsupported chip type 0x%x\n", @@ -2156,12 +2152,6 @@ static int sky2_reset(struct sky2_hw *hw) return -EOPNOTSUPP; } - /* ring for status responses */ - hw->st_le = pci_alloc_consistent(hw->pdev, STATUS_LE_BYTES, - &hw->st_dma); - if (!hw->st_le) - return -ENOMEM; - /* disable ASF */ if (hw->chip_id <= CHIP_ID_YUKON_EC) { sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET); @@ -2173,19 +2163,24 @@ static int sky2_reset(struct sky2_hw *hw) sky2_write8(hw, B0_CTST, CS_RST_CLR); /* clear PCI errors, if any */ - pci_read_config_word(hw->pdev, PCI_STATUS, &status); + err = pci_read_config_word(hw->pdev, PCI_STATUS, &status); + if (err) + goto pci_err; + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); - pci_write_config_word(hw->pdev, PCI_STATUS, - status | PCI_STATUS_ERROR_BITS); + err = pci_write_config_word(hw->pdev, PCI_STATUS, + status | PCI_STATUS_ERROR_BITS); + if (err) + goto pci_err; sky2_write8(hw, B0_CTST, CS_MRST_CLR); /* clear any PEX errors */ - if (is_pciex(hw)) { - u16 lstat; - pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT, - 0xffffffffUL); - pci_read_config_word(hw->pdev, PEX_LNK_STAT, &lstat); + if (pci_find_capability(hw->pdev, PCI_CAP_ID_EXP)) { + err = pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT, + 0xffffffffUL); + if (err) + goto pci_err; } pmd_type = sky2_read8(hw, B2_PMD_TYP); @@ -2297,6 +2292,14 @@ static int sky2_reset(struct sky2_hw *hw) sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START); return 0; + +pci_err: + /* This is to catch a BIOS bug workaround where + * mmconfig table doesn't have other buses. + */ + printk(KERN_ERR PFX "%s: can't access PCI config space\n", + pci_name(hw->pdev)); + return err; } static u32 sky2_supported_modes(const struct sky2_hw *hw) @@ -2551,19 +2554,24 @@ static struct net_device_stats *sky2_get_stats(struct net_device *dev) static int sky2_set_mac_address(struct net_device *dev, void *p) { struct sky2_port *sky2 = netdev_priv(dev); - struct sockaddr *addr = p; + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + const struct sockaddr *addr = p; if (!is_valid_ether_addr(addr->sa_data)) return -EADDRNOTAVAIL; memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN); - memcpy_toio(sky2->hw->regs + B2_MAC_1 + sky2->port * 8, + memcpy_toio(hw->regs + B2_MAC_1 + port * 8, dev->dev_addr, ETH_ALEN); - memcpy_toio(sky2->hw->regs + B2_MAC_2 + sky2->port * 8, + memcpy_toio(hw->regs + B2_MAC_2 + port * 8, dev->dev_addr, ETH_ALEN); - if (netif_running(dev)) - sky2_phy_reinit(sky2); + /* virtual address for data */ + gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr); + + /* physical address: used for pause frames */ + gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr); return 0; } @@ -2843,7 +2851,7 @@ static int sky2_set_coalesce(struct net_device *dev, if (ecmd->rx_coalesce_usecs_irq == 0) sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_STOP); else { - sky2_write32(hw, STAT_TX_TIMER_INI, + sky2_write32(hw, STAT_ISR_TIMER_INI, sky2_us2clk(hw, ecmd->rx_coalesce_usecs_irq)); sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START); } @@ -3055,6 +3063,61 @@ static void __devinit sky2_show_addr(struct net_device *dev) dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]); } +/* Handle software interrupt used during MSI test */ +static irqreturn_t __devinit sky2_test_intr(int irq, void *dev_id, + struct pt_regs *regs) +{ + struct sky2_hw *hw = dev_id; + u32 status = sky2_read32(hw, B0_Y2_SP_ISRC2); + + if (status == 0) + return IRQ_NONE; + + if (status & Y2_IS_IRQ_SW) { + sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ); + hw->msi = 1; + } + sky2_write32(hw, B0_Y2_SP_ICR, 2); + + sky2_read32(hw, B0_IMSK); + return IRQ_HANDLED; +} + +/* Test interrupt path by forcing a a software IRQ */ +static int __devinit sky2_test_msi(struct sky2_hw *hw) +{ + struct pci_dev *pdev = hw->pdev; + int i, err; + + sky2_write32(hw, B0_IMSK, Y2_IS_IRQ_SW); + + err = request_irq(pdev->irq, sky2_test_intr, SA_SHIRQ, DRV_NAME, hw); + if (err) { + printk(KERN_ERR PFX "%s: cannot assign irq %d\n", + pci_name(pdev), pdev->irq); + return err; + } + + sky2_write8(hw, B0_CTST, CS_ST_SW_IRQ); + wmb(); + + for (i = 0; i < 10; i++) { + barrier(); + if (hw->msi) + goto found; + mdelay(1); + } + + err = -EOPNOTSUPP; + sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ); + found: + sky2_write32(hw, B0_IMSK, 0); + + free_irq(pdev->irq, hw); + + return err; +} + static int __devinit sky2_probe(struct pci_dev *pdev, const struct pci_device_id *ent) { @@ -3135,6 +3198,12 @@ static int __devinit sky2_probe(struct pci_dev *pdev, } hw->pm_cap = pm_cap; + /* ring for status responses */ + hw->st_le = pci_alloc_consistent(hw->pdev, STATUS_LE_BYTES, + &hw->st_dma); + if (!hw->st_le) + goto err_out_iounmap; + err = sky2_reset(hw); if (err) goto err_out_iounmap; @@ -3169,7 +3238,22 @@ static int __devinit sky2_probe(struct pci_dev *pdev, } } - err = request_irq(pdev->irq, sky2_intr, SA_SHIRQ, DRV_NAME, hw); + if (!disable_msi && pci_enable_msi(pdev) == 0) { + err = sky2_test_msi(hw); + if (err == -EOPNOTSUPP) { + /* MSI test failed, go back to INTx mode */ + printk(KERN_WARNING PFX "%s: No interrupt was generated using MSI, " + "switching to INTx mode. Please report this failure to " + "the PCI maintainer and include system chipset information.\n", + pci_name(pdev)); + pci_disable_msi(pdev); + } + else if (err) + goto err_out_unregister; + } + + err = request_irq(pdev->irq, sky2_intr, SA_SHIRQ | SA_SAMPLE_RANDOM, + DRV_NAME, hw); if (err) { printk(KERN_ERR PFX "%s: cannot assign irq %d\n", pci_name(pdev), pdev->irq); @@ -3184,6 +3268,8 @@ static int __devinit sky2_probe(struct pci_dev *pdev, return 0; err_out_unregister: + if (hw->msi) + pci_disable_msi(pdev); if (dev1) { unregister_netdev(dev1); free_netdev(dev1); @@ -3226,6 +3312,8 @@ static void __devexit sky2_remove(struct pci_dev *pdev) sky2_read8(hw, B0_CTST); free_irq(pdev->irq, hw); + if (hw->msi) + pci_disable_msi(pdev); pci_free_consistent(pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma); pci_release_regions(pdev); pci_disable_device(pdev); @@ -3263,25 +3351,33 @@ static int sky2_suspend(struct pci_dev *pdev, pm_message_t state) static int sky2_resume(struct pci_dev *pdev) { struct sky2_hw *hw = pci_get_drvdata(pdev); - int i; + int i, err; pci_restore_state(pdev); pci_enable_wake(pdev, PCI_D0, 0); - sky2_set_power_state(hw, PCI_D0); + err = sky2_set_power_state(hw, PCI_D0); + if (err) + goto out; - sky2_reset(hw); + err = sky2_reset(hw); + if (err) + goto out; for (i = 0; i < 2; i++) { struct net_device *dev = hw->dev[i]; - if (dev) { - if (netif_running(dev)) { - netif_device_attach(dev); - if (sky2_up(dev)) - dev_close(dev); + if (dev && netif_running(dev)) { + netif_device_attach(dev); + err = sky2_up(dev); + if (err) { + printk(KERN_ERR PFX "%s: could not up: %d\n", + dev->name, err); + dev_close(dev); + break; } } } - return 0; +out: + return err; } #endif diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index 95518921001..fd12c289a23 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -1841,6 +1841,7 @@ struct sky2_hw { struct net_device *dev[2]; int pm_cap; + int msi; u8 chip_id; u8 chip_rev; u8 copper; @@ -1867,14 +1868,6 @@ static inline u8 sky2_read8(const struct sky2_hw *hw, unsigned reg) return readb(hw->regs + reg); } -/* This should probably go away, bus based tweeks suck */ -static inline int is_pciex(const struct sky2_hw *hw) -{ - u32 status; - pci_read_config_dword(hw->pdev, PCI_DEV_STATUS, &status); - return (status & PCI_OS_PCI_X) == 0; -} - static inline void sky2_write32(const struct sky2_hw *hw, unsigned reg, u32 val) { writel(val, hw->regs + reg); diff --git a/drivers/net/tulip/uli526x.c b/drivers/net/tulip/uli526x.c index 98398166680..238e9c72cb3 100644 --- a/drivers/net/tulip/uli526x.c +++ b/drivers/net/tulip/uli526x.c @@ -214,7 +214,7 @@ static u32 uli526x_cr6_user_set; /* For module input parameter */ static int debug; static u32 cr6set; -static unsigned char mode = 8; +static int mode = 8; /* function declaration ------------------------------------- */ static int uli526x_open(struct net_device *); diff --git a/drivers/net/wan/dscc4.c b/drivers/net/wan/dscc4.c index 2f61a47b471..1ff5de076d2 100644 --- a/drivers/net/wan/dscc4.c +++ b/drivers/net/wan/dscc4.c @@ -1943,7 +1943,7 @@ static int dscc4_init_ring(struct net_device *dev) (++i%TX_RING_SIZE)*sizeof(*tx_fd)); } while (i < TX_RING_SIZE); - if (dscc4_init_dummy_skb(dpriv) < 0) + if (!dscc4_init_dummy_skb(dpriv)) goto err_free_dma_tx; memset(dpriv->rx_skbuff, 0, sizeof(struct sk_buff *)*RX_RING_SIZE); diff --git a/drivers/serial/68328serial.c b/drivers/serial/68328serial.c index 8cbf0fc5a22..7f0f35a05dc 100644 --- a/drivers/serial/68328serial.c +++ b/drivers/serial/68328serial.c @@ -332,7 +332,7 @@ static _INLINE_ void receive_chars(struct m68k_serial *info, struct pt_regs *reg * Make sure that we do not overflow the buffer */ if (tty_request_buffer_room(tty, 1) == 0) { - schedule_work(&tty->flip.work); + tty_schedule_flip(tty); return; } @@ -353,7 +353,7 @@ static _INLINE_ void receive_chars(struct m68k_serial *info, struct pt_regs *reg } while((rx = uart->urx.w) & URX_DATA_READY); #endif - schedule_work(&tty->flip.work); + tty_schedule_flip(tty); clear_and_exit: return; diff --git a/drivers/serial/68360serial.c b/drivers/serial/68360serial.c index 60f5a5dc17f..9843ae3d420 100644 --- a/drivers/serial/68360serial.c +++ b/drivers/serial/68360serial.c @@ -509,7 +509,7 @@ static _INLINE_ void receive_chars(ser_info_t *info) info->rx_cur = (QUICC_BD *)bdp; - schedule_work(&tty->flip.work); + tty_schedule_flip(tty); } static _INLINE_ void receive_break(ser_info_t *info) @@ -521,7 +521,7 @@ static _INLINE_ void receive_break(ser_info_t *info) * the break. If not, we exit now, losing the break. FIXME */ tty_insert_flip_char(tty, 0, TTY_BREAK); - schedule_work(&tty->flip.work); + tty_schedule_flip(tty); } static _INLINE_ void transmit_chars(ser_info_t *info) diff --git a/drivers/serial/mcfserial.c b/drivers/serial/mcfserial.c index 0ef648fa4b2..8cbbb954df2 100644 --- a/drivers/serial/mcfserial.c +++ b/drivers/serial/mcfserial.c @@ -57,20 +57,16 @@ struct timer_list mcfrs_timer_struct; * keep going. Perhaps one day the cflag settings for the * console can be used instead. */ -#if defined(CONFIG_ARNEWSH) || defined(CONFIG_FREESCALE) || \ - defined(CONFIG_senTec) || defined(CONFIG_SNEHA) -#define CONSOLE_BAUD_RATE 19200 -#define DEFAULT_CBAUD B19200 -#endif - #if defined(CONFIG_HW_FEITH) #define CONSOLE_BAUD_RATE 38400 #define DEFAULT_CBAUD B38400 -#endif - -#if defined(CONFIG_MOD5272) || defined(CONFIG_M5208EVB) +#elif defined(CONFIG_MOD5272) || defined(CONFIG_M5208EVB) #define CONSOLE_BAUD_RATE 115200 #define DEFAULT_CBAUD B115200 +#elif defined(CONFIG_ARNEWSH) || defined(CONFIG_FREESCALE) || \ + defined(CONFIG_senTec) || defined(CONFIG_SNEHA) +#define CONSOLE_BAUD_RATE 19200 +#define DEFAULT_CBAUD B19200 #endif #ifndef CONSOLE_BAUD_RATE @@ -350,7 +346,7 @@ static inline void receive_chars(struct mcf_serial *info) } tty_insert_flip_char(tty, ch, flag); } - tty_flip_buffer_push(tty); + tty_schedule_flip(tty); return; } |