53 files changed, 2830 insertions, 828 deletions

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 2967002a9f8..363498697c2 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -63,33 +63,58 @@ config GPIO_SYSFS
 	  Kernel drivers may also request that a particular GPIO be
 	  exported to userspace; this can be useful when debugging.
 
+config GPIO_GENERIC
+	tristate
+
 # put drivers in the right section, in alphabetical order
 
+config GPIO_DA9052
+	tristate "Dialog DA9052 GPIO"
+	depends on PMIC_DA9052
+	help
+	  Say yes here to enable the GPIO driver for the DA9052 chip.
+
 config GPIO_MAX730X
 	tristate
 
 comment "Memory mapped GPIO drivers:"
 
-config GPIO_BASIC_MMIO_CORE
-	tristate
-	help
-	  Provides core functionality for basic memory-mapped GPIO controllers.
-
-config GPIO_BASIC_MMIO
-	tristate "Basic memory-mapped GPIO controllers support"
-	select GPIO_BASIC_MMIO_CORE
+config GPIO_GENERIC_PLATFORM
+	tristate "Generic memory-mapped GPIO controller support (MMIO platform device)"
+	select GPIO_GENERIC
 	help
-	  Say yes here to support basic memory-mapped GPIO controllers.
+	  Say yes here to support basic platform_device memory-mapped GPIO controllers.
 
 config GPIO_IT8761E
 	tristate "IT8761E GPIO support"
 	help
 	  Say yes here to support GPIO functionality of IT8761E super I/O chip.
 
+config GPIO_EP93XX
+	def_bool y
+	depends on ARCH_EP93XX
+	select GPIO_GENERIC
+
 config GPIO_EXYNOS4
 	def_bool y
 	depends on CPU_EXYNOS4210
 
+config GPIO_MPC5200
+	def_bool y
+	depends on PPC_MPC52xx
+
+config GPIO_MXC
+	def_bool y
+	depends on ARCH_MXC
+	select GPIO_GENERIC
+	select GENERIC_IRQ_CHIP
+
+config GPIO_MXS
+	def_bool y
+	depends on ARCH_MXS
+	select GPIO_GENERIC
+	select GENERIC_IRQ_CHIP
+
 config GPIO_PLAT_SAMSUNG
 	def_bool y
 	depends on SAMSUNG_GPIOLIB_4BIT
@@ -137,9 +162,6 @@ config GPIO_SCH
 	  The Intel Tunnel Creek processor has 5 GPIOs powered by the
 	  core power rail and 9 from suspend power supply.
 
-	  This driver can also be built as a module. If so, the module
-	  will be called sch-gpio.
-
 config GPIO_VX855
 	tristate "VIA VX855/VX875 GPIO"
 	depends on MFD_SUPPORT && PCI
@@ -202,9 +224,6 @@ config GPIO_PCA953X
 
 	  16 bits:	pca9535, pca9539, pca9555, tca6416
 
-	  This driver can also be built as a module.  If so, the module
-	  will be called pca953x.
-
 config GPIO_PCA953X_IRQ
 	bool "Interrupt controller support for PCA953x"
 	depends on GPIO_PCA953X=y
@@ -296,17 +315,12 @@ config GPIO_ADP5520
 	  This option enables support for on-chip GPIO found
 	  on Analog Devices ADP5520 PMICs.
 
-	  To compile this driver as a module, choose M here: the module will
-	  be called adp5520-gpio.
-
 config GPIO_ADP5588
 	tristate "ADP5588 I2C GPIO expander"
 	depends on I2C
 	help
 	  This option enables support for 18 GPIOs found
 	  on Analog Devices ADP5588 GPIO Expanders.
-	  To compile this driver as a module, choose M here: the module will be
-	  called adp5588-gpio.
 
 config GPIO_ADP5588_IRQ
 	bool "Interrupt controller support for ADP5588"
@@ -398,10 +412,11 @@ config GPIO_MAX7301
 	  GPIO driver for Maxim MAX7301 SPI-based GPIO expander.
 
 config GPIO_MCP23S08
-	tristate "Microchip MCP23Sxx I/O expander"
-	depends on SPI_MASTER
+	tristate "Microchip MCP23xxx I/O expander"
+	depends on SPI_MASTER || I2C
 	help
-	  SPI driver for Microchip MCP23S08/MPC23S17 I/O expanders.
+	  SPI/I2C driver for Microchip MCP23S08/MCP23S17/MCP23008/MCP23017
+	  I/O expanders.
 	  This provides a GPIO interface supporting inputs and outputs.
 
 config GPIO_MC33880
@@ -428,9 +443,6 @@ config GPIO_UCB1400
 	  This enables support for the Philips UCB1400 GPIO pins.
 	  The UCB1400 is an AC97 audio codec.
 
-	  To compile this driver as a module, choose M here: the
-	  module will be called ucb1400_gpio.
-
 comment "MODULbus GPIO expanders:"
 
 config GPIO_JANZ_TTL
@@ -441,7 +453,7 @@ config GPIO_JANZ_TTL
 	  This driver provides support for driving the pins in output
 	  mode only. Input mode is not supported.
 
-config AB8500_GPIO
+config GPIO_AB8500
 	bool "ST-Ericsson AB8500 Mixed Signal Circuit gpio functions"
 	depends on AB8500_CORE && BROKEN
 	help
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index b605f8ec6fb..72071125139 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -4,47 +4,56 @@ ccflags-$(CONFIG_DEBUG_GPIO)	+= -DDEBUG
 
 obj-$(CONFIG_GPIOLIB)		+= gpiolib.o
 
-obj-$(CONFIG_GPIO_ADP5520)	+= adp5520-gpio.o
-obj-$(CONFIG_GPIO_ADP5588)	+= adp5588-gpio.o
-obj-$(CONFIG_GPIO_BASIC_MMIO_CORE)	+= basic_mmio_gpio.o
-obj-$(CONFIG_GPIO_BASIC_MMIO)	+= basic_mmio_gpio.o
+# Device drivers. Generally keep list sorted alphabetically
+obj-$(CONFIG_GPIO_GENERIC)	+= gpio-generic.o
+
+obj-$(CONFIG_GPIO_74X164)	+= gpio-74x164.o
+obj-$(CONFIG_GPIO_AB8500)	+= gpio-ab8500.o
+obj-$(CONFIG_GPIO_ADP5520)	+= gpio-adp5520.o
+obj-$(CONFIG_GPIO_ADP5588)	+= gpio-adp5588.o
+obj-$(CONFIG_GPIO_BT8XX)	+= gpio-bt8xx.o
+obj-$(CONFIG_GPIO_CS5535)	+= gpio-cs5535.o
+obj-$(CONFIG_GPIO_DA9052)	+= gpio-da9052.o
+obj-$(CONFIG_GPIO_EP93XX)	+= gpio-ep93xx.o
 obj-$(CONFIG_GPIO_EXYNOS4)	+= gpio-exynos4.o
+obj-$(CONFIG_GPIO_IT8761E)	+= gpio-it8761e.o
+obj-$(CONFIG_GPIO_JANZ_TTL)	+= gpio-janz-ttl.o
+obj-$(CONFIG_GPIO_LANGWELL)	+= gpio-langwell.o
+obj-$(CONFIG_GPIO_MAX730X)	+= gpio-max730x.o
+obj-$(CONFIG_GPIO_MAX7300)	+= gpio-max7300.o
+obj-$(CONFIG_GPIO_MAX7301)	+= gpio-max7301.o
+obj-$(CONFIG_GPIO_MAX732X)	+= gpio-max732x.o
+obj-$(CONFIG_GPIO_MC33880)	+= gpio-mc33880.o
+obj-$(CONFIG_GPIO_MCP23S08)	+= gpio-mcp23s08.o
+obj-$(CONFIG_GPIO_ML_IOH)	+= gpio-ml-ioh.o
+obj-$(CONFIG_GPIO_MPC5200)	+= gpio-mpc5200.o
+obj-$(CONFIG_GPIO_MXC)		+= gpio-mxc.o
+obj-$(CONFIG_GPIO_MXS)		+= gpio-mxs.o
+obj-$(CONFIG_PLAT_NOMADIK)	+= gpio-nomadik.o
+obj-$(CONFIG_ARCH_OMAP)		+= gpio-omap.o
+obj-$(CONFIG_GPIO_PCA953X)	+= gpio-pca953x.o
+obj-$(CONFIG_GPIO_PCF857X)	+= gpio-pcf857x.o
+obj-$(CONFIG_GPIO_PCH)		+= gpio-pch.o
+obj-$(CONFIG_GPIO_PL061)	+= gpio-pl061.o
+obj-$(CONFIG_GPIO_RDC321X)	+= gpio-rdc321x.o
+
 obj-$(CONFIG_GPIO_PLAT_SAMSUNG)	+= gpio-plat-samsung.o
 obj-$(CONFIG_GPIO_S5PC100)	+= gpio-s5pc100.o
 obj-$(CONFIG_GPIO_S5PV210)	+= gpio-s5pv210.o
-obj-$(CONFIG_GPIO_LANGWELL)	+= langwell_gpio.o
-obj-$(CONFIG_GPIO_MAX730X)	+= max730x.o
-obj-$(CONFIG_GPIO_MAX7300)	+= max7300.o
-obj-$(CONFIG_GPIO_MAX7301)	+= max7301.o
-obj-$(CONFIG_GPIO_MAX732X)	+= max732x.o
-obj-$(CONFIG_GPIO_MC33880)	+= mc33880.o
-obj-$(CONFIG_GPIO_MCP23S08)	+= mcp23s08.o
-obj-$(CONFIG_GPIO_74X164)	+= 74x164.o
-obj-$(CONFIG_ARCH_OMAP)         += gpio-omap.o
-obj-$(CONFIG_GPIO_PCA953X)	+= pca953x.o
-obj-$(CONFIG_GPIO_PCF857X)	+= pcf857x.o
-obj-$(CONFIG_GPIO_PCH)		+= pch_gpio.o
-obj-$(CONFIG_GPIO_PL061)	+= pl061.o
-obj-$(CONFIG_GPIO_STMPE)	+= stmpe-gpio.o
-obj-$(CONFIG_GPIO_TC3589X)	+= tc3589x-gpio.o
-obj-$(CONFIG_GPIO_TIMBERDALE)	+= timbgpio.o
-obj-$(CONFIG_GPIO_TWL4030)	+= twl4030-gpio.o
-obj-$(CONFIG_GPIO_UCB1400)	+= ucb1400_gpio.o
-obj-$(CONFIG_GPIO_XILINX)	+= xilinx_gpio.o
-obj-$(CONFIG_GPIO_CS5535)	+= cs5535-gpio.o
-obj-$(CONFIG_GPIO_BT8XX)	+= bt8xxgpio.o
-obj-$(CONFIG_GPIO_IT8761E)	+= it8761e_gpio.o
-obj-$(CONFIG_GPIO_VR41XX)	+= vr41xx_giu.o
-obj-$(CONFIG_GPIO_WM831X)	+= wm831x-gpio.o
-obj-$(CONFIG_GPIO_WM8350)	+= wm8350-gpiolib.o
-obj-$(CONFIG_GPIO_WM8994)	+= wm8994-gpio.o
-obj-$(CONFIG_GPIO_SCH)		+= sch_gpio.o
+
+obj-$(CONFIG_GPIO_SCH)		+= gpio-sch.o
+obj-$(CONFIG_GPIO_STMPE)	+= gpio-stmpe.o
+obj-$(CONFIG_GPIO_SX150X)	+= gpio-sx150x.o
+obj-$(CONFIG_GPIO_TC3589X)	+= gpio-tc3589x.o
+obj-$(CONFIG_ARCH_TEGRA)	+= gpio-tegra.o
+obj-$(CONFIG_GPIO_TIMBERDALE)	+= gpio-timberdale.o
+obj-$(CONFIG_GPIO_TPS65910)	+= gpio-tps65910.o
+obj-$(CONFIG_GPIO_TWL4030)	+= gpio-twl4030.o
 obj-$(CONFIG_MACH_U300)		+= gpio-u300.o
-obj-$(CONFIG_PLAT_NOMADIK)	+= gpio-nomadik.o
-obj-$(CONFIG_GPIO_RDC321X)	+= rdc321x-gpio.o
-obj-$(CONFIG_GPIO_JANZ_TTL)	+= janz-ttl.o
-obj-$(CONFIG_GPIO_SX150X)	+= sx150x.o
-obj-$(CONFIG_GPIO_VX855)	+= vx855_gpio.o
-obj-$(CONFIG_GPIO_ML_IOH)	+= ml_ioh_gpio.o
-obj-$(CONFIG_AB8500_GPIO)       += ab8500-gpio.o
-obj-$(CONFIG_GPIO_TPS65910)	+= tps65910-gpio.o
+obj-$(CONFIG_GPIO_UCB1400)	+= gpio-ucb1400.o
+obj-$(CONFIG_GPIO_VR41XX)	+= gpio-vr41xx.o
+obj-$(CONFIG_GPIO_VX855)	+= gpio-vx855.o
+obj-$(CONFIG_GPIO_WM831X)	+= gpio-wm831x.o
+obj-$(CONFIG_GPIO_WM8350)	+= gpio-wm8350.o
+obj-$(CONFIG_GPIO_WM8994)	+= gpio-wm8994.o
+obj-$(CONFIG_GPIO_XILINX)	+= gpio-xilinx.o
diff --git a/drivers/gpio/74x164.c b/drivers/gpio/gpio-74x164.c
index 84e07021983..ff525c0958d 100644
--- a/drivers/gpio/74x164.c
+++ b/drivers/gpio/gpio-74x164.c
@@ -16,9 +16,6 @@
 #include <linux/gpio.h>
 #include <linux/slab.h>
 
-#define GEN_74X164_GPIO_COUNT	8
-
-
 struct gen_74x164_chip {
 	struct spi_device	*spi;
 	struct gpio_chip	gpio_chip;
@@ -26,9 +23,7 @@ struct gen_74x164_chip {
 	u8			port_config;
 };
 
-static void gen_74x164_set_value(struct gpio_chip *, unsigned, int);
-
-static struct gen_74x164_chip *gpio_to_chip(struct gpio_chip *gc)
+static struct gen_74x164_chip *gpio_to_74x164_chip(struct gpio_chip *gc)
 {
 	return container_of(gc, struct gen_74x164_chip, gpio_chip);
 }
@@ -39,16 +34,9 @@ static int __gen_74x164_write_config(struct gen_74x164_chip *chip)
 			 &chip->port_config, sizeof(chip->port_config));
 }
 
-static int gen_74x164_direction_output(struct gpio_chip *gc,
-		unsigned offset, int val)
-{
-	gen_74x164_set_value(gc, offset, val);
-	return 0;
-}
-
 static int gen_74x164_get_value(struct gpio_chip *gc, unsigned offset)
 {
-	struct gen_74x164_chip *chip = gpio_to_chip(gc);
+	struct gen_74x164_chip *chip = gpio_to_74x164_chip(gc);
 	int ret;
 
 	mutex_lock(&chip->lock);
@@ -61,7 +49,7 @@ static int gen_74x164_get_value(struct gpio_chip *gc, unsigned offset)
 static void gen_74x164_set_value(struct gpio_chip *gc,
 		unsigned offset, int val)
 {
-	struct gen_74x164_chip *chip = gpio_to_chip(gc);
+	struct gen_74x164_chip *chip = gpio_to_74x164_chip(gc);
 
 	mutex_lock(&chip->lock);
 	if (val)
@@ -73,6 +61,13 @@ static void gen_74x164_set_value(struct gpio_chip *gc,
 	mutex_unlock(&chip->lock);
 }
 
+static int gen_74x164_direction_output(struct gpio_chip *gc,
+		unsigned offset, int val)
+{
+	gen_74x164_set_value(gc, offset, val);
+	return 0;
+}
+
 static int __devinit gen_74x164_probe(struct spi_device *spi)
 {
 	struct gen_74x164_chip *chip;
@@ -104,12 +99,12 @@ static int __devinit gen_74x164_probe(struct spi_device *spi)
 
 	chip->spi = spi;
 
-	chip->gpio_chip.label = GEN_74X164_DRIVER_NAME,
-		chip->gpio_chip.direction_output = gen_74x164_direction_output;
+	chip->gpio_chip.label = spi->modalias;
+	chip->gpio_chip.direction_output = gen_74x164_direction_output;
 	chip->gpio_chip.get = gen_74x164_get_value;
 	chip->gpio_chip.set = gen_74x164_set_value;
 	chip->gpio_chip.base = pdata->base;
-	chip->gpio_chip.ngpio = GEN_74X164_GPIO_COUNT;
+	chip->gpio_chip.ngpio = 8;
 	chip->gpio_chip.can_sleep = 1;
 	chip->gpio_chip.dev = &spi->dev;
 	chip->gpio_chip.owner = THIS_MODULE;
@@ -157,7 +152,7 @@ static int __devexit gen_74x164_remove(struct spi_device *spi)
 
 static struct spi_driver gen_74x164_driver = {
 	.driver = {
-		.name		= GEN_74X164_DRIVER_NAME,
+		.name		= "74x164",
 		.owner		= THIS_MODULE,
 	},
 	.probe		= gen_74x164_probe,
diff --git a/drivers/gpio/ab8500-gpio.c b/drivers/gpio/gpio-ab8500.c
index 970053c89ff..970053c89ff 100644
--- a/drivers/gpio/ab8500-gpio.c
+++ b/drivers/gpio/gpio-ab8500.c
diff --git a/drivers/gpio/adp5520-gpio.c b/drivers/gpio/gpio-adp5520.c
index 9f278153700..9f278153700 100644
--- a/drivers/gpio/adp5520-gpio.c
+++ b/drivers/gpio/gpio-adp5520.c
diff --git a/drivers/gpio/adp5588-gpio.c b/drivers/gpio/gpio-adp5588.c
index 3525ad91877..3525ad91877 100644
--- a/drivers/gpio/adp5588-gpio.c
+++ b/drivers/gpio/gpio-adp5588.c
diff --git a/drivers/gpio/bt8xxgpio.c b/drivers/gpio/gpio-bt8xx.c
index aa4f09ad3ce..aa4f09ad3ce 100644
--- a/drivers/gpio/bt8xxgpio.c
+++ b/drivers/gpio/gpio-bt8xx.c
diff --git a/drivers/gpio/cs5535-gpio.c b/drivers/gpio/gpio-cs5535.c
index 6e16cba56ad..6e16cba56ad 100644
--- a/drivers/gpio/cs5535-gpio.c
+++ b/drivers/gpio/gpio-cs5535.c
diff --git a/drivers/gpio/gpio-da9052.c b/drivers/gpio/gpio-da9052.c
new file mode 100644
index 00000000000..038f5eb8b13
--- /dev/null
+++ b/drivers/gpio/gpio-da9052.c
@@ -0,0 +1,277 @@
+/*
+ * GPIO Driver for Dialog DA9052 PMICs.
+ *
+ * Copyright(c) 2011 Dialog Semiconductor Ltd.
+ *
+ * Author: David Dajun Chen <dchen@diasemi.com>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ */
+#include <linux/module.h>
+#include <linux/fs.h>
+#include <linux/uaccess.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/syscalls.h>
+#include <linux/seq_file.h>
+
+#include <linux/mfd/da9052/da9052.h>
+#include <linux/mfd/da9052/reg.h>
+#include <linux/mfd/da9052/pdata.h>
+#include <linux/mfd/da9052/gpio.h>
+
+#define DA9052_INPUT				1
+#define DA9052_OUTPUT_OPENDRAIN		2
+#define DA9052_OUTPUT_PUSHPULL			3
+
+#define DA9052_SUPPLY_VDD_IO1			0
+
+#define DA9052_DEBOUNCING_OFF			0
+#define DA9052_DEBOUNCING_ON			1
+
+#define DA9052_OUTPUT_LOWLEVEL			0
+
+#define DA9052_ACTIVE_LOW			0
+#define DA9052_ACTIVE_HIGH			1
+
+#define DA9052_GPIO_MAX_PORTS_PER_REGISTER	8
+#define DA9052_GPIO_SHIFT_COUNT(no)		(no%8)
+#define DA9052_GPIO_MASK_UPPER_NIBBLE		0xF0
+#define DA9052_GPIO_MASK_LOWER_NIBBLE		0x0F
+#define DA9052_GPIO_NIBBLE_SHIFT		4
+
+struct da9052_gpio {
+	struct da9052 *da9052;
+	struct gpio_chip gp;
+};
+
+static inline struct da9052_gpio *to_da9052_gpio(struct gpio_chip *chip)
+{
+	return container_of(chip, struct da9052_gpio, gp);
+}
+
+static unsigned char da9052_gpio_port_odd(unsigned offset)
+{
+	return offset % 2;
+}
+
+static int da9052_gpio_get(struct gpio_chip *gc, unsigned offset)
+{
+	struct da9052_gpio *gpio = to_da9052_gpio(gc);
+	int da9052_port_direction = 0;
+	int ret;
+
+	ret = da9052_reg_read(gpio->da9052,
+			      DA9052_GPIO_0_1_REG + (offset >> 1));
+	if (ret < 0)
+		return ret;
+
+	if (da9052_gpio_port_odd(offset)) {
+		da9052_port_direction = ret & DA9052_GPIO_ODD_PORT_PIN;
+		da9052_port_direction >>= 4;
+	} else {
+		da9052_port_direction = ret & DA9052_GPIO_EVEN_PORT_PIN;
+	}
+
+	switch (da9052_port_direction) {
+	case DA9052_INPUT:
+		if (offset < DA9052_GPIO_MAX_PORTS_PER_REGISTER)
+			ret = da9052_reg_read(gpio->da9052,
+					      DA9052_STATUS_C_REG);
+		else
+			ret = da9052_reg_read(gpio->da9052,
+					      DA9052_STATUS_D_REG);
+		if (ret < 0)
+			return ret;
+		if (ret & (1 << DA9052_GPIO_SHIFT_COUNT(offset)))
+			return 1;
+		else
+			return 0;
+	case DA9052_OUTPUT_PUSHPULL:
+		if (da9052_gpio_port_odd(offset))
+			return ret & DA9052_GPIO_ODD_PORT_MODE;
+		else
+			return ret & DA9052_GPIO_EVEN_PORT_MODE;
+	default:
+		return -EINVAL;
+	}
+}
+
+static void da9052_gpio_set(struct gpio_chip *gc, unsigned offset, int value)
+{
+	struct da9052_gpio *gpio = to_da9052_gpio(gc);
+	unsigned char register_value = 0;
+	int ret;
+
+	if (da9052_gpio_port_odd(offset)) {
+		if (value) {
+			register_value = DA9052_GPIO_ODD_PORT_MODE;
+			ret = da9052_reg_update(gpio->da9052, (offset >> 1) +
+						DA9052_GPIO_0_1_REG,
+						DA9052_GPIO_ODD_PORT_MODE,
+						register_value);
+			if (ret != 0)
+				dev_err(gpio->da9052->dev,
+					"Failed to updated gpio odd reg,%d",
+					ret);
+		}
+	} else {
+		if (value) {
+			register_value = DA9052_GPIO_EVEN_PORT_MODE;
+			ret = da9052_reg_update(gpio->da9052, (offset >> 1) +
+						DA9052_GPIO_0_1_REG,
+						DA9052_GPIO_EVEN_PORT_MODE,
+						register_value);
+			if (ret != 0)
+				dev_err(gpio->da9052->dev,
+					"Failed to updated gpio even reg,%d",
+					ret);
+		}
+	}
+}
+
+static int da9052_gpio_direction_input(struct gpio_chip *gc, unsigned offset)
+{
+	struct da9052_gpio *gpio = to_da9052_gpio(gc);
+	unsigned char register_value;
+	int ret;
+
+	/* Format: function - 2 bits type - 1 bit mode - 1 bit */
+	register_value = DA9052_INPUT | DA9052_ACTIVE_LOW << 2 |
+			 DA9052_DEBOUNCING_ON << 3;
+
+	if (da9052_gpio_port_odd(offset))
+		ret = da9052_reg_update(gpio->da9052, (offset >> 1) +
+					DA9052_GPIO_0_1_REG,
+					DA9052_GPIO_MASK_UPPER_NIBBLE,
+					(register_value <<
+					DA9052_GPIO_NIBBLE_SHIFT));
+	else
+		ret = da9052_reg_update(gpio->da9052, (offset >> 1) +
+					DA9052_GPIO_0_1_REG,
+					DA9052_GPIO_MASK_LOWER_NIBBLE,
+					register_value);
+
+	return ret;
+}
+
+static int da9052_gpio_direction_output(struct gpio_chip *gc,
+					unsigned offset, int value)
+{
+	struct da9052_gpio *gpio = to_da9052_gpio(gc);
+	unsigned char register_value;
+	int ret;
+
+	/* Format: Function - 2 bits Type - 1 bit Mode - 1 bit */
+	register_value = DA9052_OUTPUT_PUSHPULL | DA9052_SUPPLY_VDD_IO1 << 2 |
+			 value << 3;
+
+	if (da9052_gpio_port_odd(offset))
+		ret = da9052_reg_update(gpio->da9052, (offset >> 1) +
+					DA9052_GPIO_0_1_REG,
+					DA9052_GPIO_MASK_UPPER_NIBBLE,
+					(register_value <<
+					DA9052_GPIO_NIBBLE_SHIFT));
+	else
+		ret = da9052_reg_update(gpio->da9052, (offset >> 1) +
+					DA9052_GPIO_0_1_REG,
+					DA9052_GPIO_MASK_LOWER_NIBBLE,
+					register_value);
+
+	return ret;
+}
+
+static int da9052_gpio_to_irq(struct gpio_chip *gc, u32 offset)
+{
+	struct da9052_gpio *gpio = to_da9052_gpio(gc);
+	struct da9052 *da9052 = gpio->da9052;
+
+	return da9052->irq_base + DA9052_IRQ_GPI0 + offset;
+}
+
+static struct gpio_chip reference_gp __devinitdata = {
+	.label = "da9052-gpio",
+	.owner = THIS_MODULE,
+	.get = da9052_gpio_get,
+	.set = da9052_gpio_set,
+	.direction_input = da9052_gpio_direction_input,
+	.direction_output = da9052_gpio_direction_output,
+	.to_irq = da9052_gpio_to_irq,
+	.can_sleep = 1;
+	.ngpio = 16;
+	.base = -1;
+};
+
+static int __devinit da9052_gpio_probe(struct platform_device *pdev)
+{
+	struct da9052_gpio *gpio;
+	struct da9052_pdata *pdata;
+	int ret;
+
+	gpio = kzalloc(sizeof(*gpio), GFP_KERNEL);
+	if (gpio == NULL)
+		return -ENOMEM;
+
+	gpio->da9052 = dev_get_drvdata(pdev->dev.parent);
+	pdata = gpio->da9052->dev->platform_data;
+
+	gpio->gp = reference_gp;
+	if (pdata && pdata->gpio_base)
+		gpio->gp.base = pdata->gpio_base;
+
+	ret = gpiochip_add(&gpio->gp);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Could not register gpiochip, %d\n", ret);
+		goto err_mem;
+	}
+
+	platform_set_drvdata(pdev, gpio);
+
+	return 0;
+
+err_mem:
+	kfree(gpio);
+	return ret;
+}
+
+static int __devexit da9052_gpio_remove(struct platform_device *pdev)
+{
+	struct da9052_gpio *gpio = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = gpiochip_remove(&gpio->gp);
+	if (ret == 0)
+		kfree(gpio);
+
+	return ret;
+}
+
+static struct platform_driver da9052_gpio_driver = {
+	.probe = da9052_gpio_probe,
+	.remove = __devexit_p(da9052_gpio_remove),
+	.driver = {
+		.name	= "da9052-gpio",
+		.owner	= THIS_MODULE,
+	},
+};
+
+static int __init da9052_gpio_init(void)
+{
+	return platform_driver_register(&da9052_gpio_driver);
+}
+module_init(da9052_gpio_init);
+
+static void __exit da9052_gpio_exit(void)
+{
+	return platform_driver_unregister(&da9052_gpio_driver);
+}
+module_exit(da9052_gpio_exit);
+
+MODULE_AUTHOR("David Dajun Chen <dchen@diasemi.com>");
+MODULE_DESCRIPTION("DA9052 GPIO Device Driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:da9052-gpio");
diff --git a/drivers/gpio/gpio-ep93xx.c b/drivers/gpio/gpio-ep93xx.c
new file mode 100644
index 00000000000..3bfd3417ab1
--- /dev/null
+++ b/drivers/gpio/gpio-ep93xx.c
@@ -0,0 +1,405 @@
+/*
+ * Generic EP93xx GPIO handling
+ *
+ * Copyright (c) 2008 Ryan Mallon <ryan@bluewatersys.com>
+ * Copyright (c) 2011 H Hartley Sweeten <hsweeten@visionengravers.com>
+ *
+ * Based on code originally from:
+ *  linux/arch/arm/mach-ep93xx/core.c
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
+#include <linux/slab.h>
+#include <linux/basic_mmio_gpio.h>
+
+#include <mach/hardware.h>
+
+struct ep93xx_gpio {
+	void __iomem		*mmio_base;
+	struct bgpio_chip	bgc[8];
+};
+
+/*************************************************************************
+ * Interrupt handling for EP93xx on-chip GPIOs
+ *************************************************************************/
+static unsigned char gpio_int_unmasked[3];
+static unsigned char gpio_int_enabled[3];
+static unsigned char gpio_int_type1[3];
+static unsigned char gpio_int_type2[3];
+static unsigned char gpio_int_debounce[3];
+
+/* Port ordering is: A B F */
+static const u8 int_type1_register_offset[3]	= { 0x90, 0xac, 0x4c };
+static const u8 int_type2_register_offset[3]	= { 0x94, 0xb0, 0x50 };
+static const u8 eoi_register_offset[3]		= { 0x98, 0xb4, 0x54 };
+static const u8 int_en_register_offset[3]	= { 0x9c, 0xb8, 0x58 };
+static const u8 int_debounce_register_offset[3]	= { 0xa8, 0xc4, 0x64 };
+
+static void ep93xx_gpio_update_int_params(unsigned port)
+{
+	BUG_ON(port > 2);
+
+	__raw_writeb(0, EP93XX_GPIO_REG(int_en_register_offset[port]));
+
+	__raw_writeb(gpio_int_type2[port],
+		EP93XX_GPIO_REG(int_type2_register_offset[port]));
+
+	__raw_writeb(gpio_int_type1[port],
+		EP93XX_GPIO_REG(int_type1_register_offset[port]));
+
+	__raw_writeb(gpio_int_unmasked[port] & gpio_int_enabled[port],
+		EP93XX_GPIO_REG(int_en_register_offset[port]));
+}
+
+static inline void ep93xx_gpio_int_mask(unsigned line)
+{
+	gpio_int_unmasked[line >> 3] &= ~(1 << (line & 7));
+}
+
+static void ep93xx_gpio_int_debounce(unsigned int irq, bool enable)
+{
+	int line = irq_to_gpio(irq);
+	int port = line >> 3;
+	int port_mask = 1 << (line & 7);
+
+	if (enable)
+		gpio_int_debounce[port] |= port_mask;
+	else
+		gpio_int_debounce[port] &= ~port_mask;
+
+	__raw_writeb(gpio_int_debounce[port],
+		EP93XX_GPIO_REG(int_debounce_register_offset[port]));
+}
+
+static void ep93xx_gpio_ab_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	unsigned char status;
+	int i;
+
+	status = __raw_readb(EP93XX_GPIO_A_INT_STATUS);
+	for (i = 0; i < 8; i++) {
+		if (status & (1 << i)) {
+			int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_A(0)) + i;
+			generic_handle_irq(gpio_irq);
+		}
+	}
+
+	status = __raw_readb(EP93XX_GPIO_B_INT_STATUS);
+	for (i = 0; i < 8; i++) {
+		if (status & (1 << i)) {
+			int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_B(0)) + i;
+			generic_handle_irq(gpio_irq);
+		}
+	}
+}
+
+static void ep93xx_gpio_f_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	/*
+	 * map discontiguous hw irq range to continuous sw irq range:
+	 *
+	 *  IRQ_EP93XX_GPIO{0..7}MUX -> gpio_to_irq(EP93XX_GPIO_LINE_F({0..7})
+	 */
+	int port_f_idx = ((irq + 1) & 7) ^ 4; /* {19..22,47..50} -> {0..7} */
+	int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_F(0)) + port_f_idx;
+
+	generic_handle_irq(gpio_irq);
+}
+
+static void ep93xx_gpio_irq_ack(struct irq_data *d)
+{
+	int line = irq_to_gpio(d->irq);
+	int port = line >> 3;
+	int port_mask = 1 << (line & 7);
+
+	if (irqd_get_trigger_type(d) == IRQ_TYPE_EDGE_BOTH) {
+		gpio_int_type2[port] ^= port_mask; /* switch edge direction */
+		ep93xx_gpio_update_int_params(port);
+	}
+
+	__raw_writeb(port_mask, EP93XX_GPIO_REG(eoi_register_offset[port]));
+}
+
+static void ep93xx_gpio_irq_mask_ack(struct irq_data *d)
+{
+	int line = irq_to_gpio(d->irq);
+	int port = line >> 3;
+	int port_mask = 1 << (line & 7);
+
+	if (irqd_get_trigger_type(d) == IRQ_TYPE_EDGE_BOTH)
+		gpio_int_type2[port] ^= port_mask; /* switch edge direction */
+
+	gpio_int_unmasked[port] &= ~port_mask;
+	ep93xx_gpio_update_int_params(port);
+
+	__raw_writeb(port_mask, EP93XX_GPIO_REG(eoi_register_offset[port]));
+}
+
+static void ep93xx_gpio_irq_mask(struct irq_data *d)
+{
+	int line = irq_to_gpio(d->irq);
+	int port = line >> 3;
+
+	gpio_int_unmasked[port] &= ~(1 << (line & 7));
+	ep93xx_gpio_update_int_params(port);
+}
+
+static void ep93xx_gpio_irq_unmask(struct irq_data *d)
+{
+	int line = irq_to_gpio(d->irq);
+	int port = line >> 3;
+
+	gpio_int_unmasked[port] |= 1 << (line & 7);
+	ep93xx_gpio_update_int_params(port);
+}
+
+/*
+ * gpio_int_type1 controls whether the interrupt is level (0) or
+ * edge (1) triggered, while gpio_int_type2 controls whether it
+ * triggers on low/falling (0) or high/rising (1).
+ */
+static int ep93xx_gpio_irq_type(struct irq_data *d, unsigned int type)
+{
+	const int gpio = irq_to_gpio(d->irq);
+	const int port = gpio >> 3;
+	const int port_mask = 1 << (gpio & 7);
+	irq_flow_handler_t handler;
+
+	gpio_direction_input(gpio);
+
+	switch (type) {
+	case IRQ_TYPE_EDGE_RISING:
+		gpio_int_type1[port] |= port_mask;
+		gpio_int_type2[port] |= port_mask;
+		handler = handle_edge_irq;
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		gpio_int_type1[port] |= port_mask;
+		gpio_int_type2[port] &= ~port_mask;
+		handler = handle_edge_irq;
+		break;
+	case IRQ_TYPE_LEVEL_HIGH:
+		gpio_int_type1[port] &= ~port_mask;
+		gpio_int_type2[port] |= port_mask;
+		handler = handle_level_irq;
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		gpio_int_type1[port] &= ~port_mask;
+		gpio_int_type2[port] &= ~port_mask;
+		handler = handle_level_irq;
+		break;
+	case IRQ_TYPE_EDGE_BOTH:
+		gpio_int_type1[port] |= port_mask;
+		/* set initial polarity based on current input level */
+		if (gpio_get_value(gpio))
+			gpio_int_type2[port] &= ~port_mask; /* falling */
+		else
+			gpio_int_type2[port] |= port_mask; /* rising */
+		handler = handle_edge_irq;
+		break;
+	default:
+		pr_err("failed to set irq type %d for gpio %d\n", type, gpio);
+		return -EINVAL;
+	}
+
+	__irq_set_handler_locked(d->irq, handler);
+
+	gpio_int_enabled[port] |= port_mask;
+
+	ep93xx_gpio_update_int_params(port);
+
+	return 0;
+}
+
+static struct irq_chip ep93xx_gpio_irq_chip = {
+	.name		= "GPIO",
+	.irq_ack	= ep93xx_gpio_irq_ack,
+	.irq_mask_ack	= ep93xx_gpio_irq_mask_ack,
+	.irq_mask	= ep93xx_gpio_irq_mask,
+	.irq_unmask	= ep93xx_gpio_irq_unmask,
+	.irq_set_type	= ep93xx_gpio_irq_type,
+};
+
+static void ep93xx_gpio_init_irq(void)
+{
+	int gpio_irq;
+
+	for (gpio_irq = gpio_to_irq(0);
+	     gpio_irq <= gpio_to_irq(EP93XX_GPIO_LINE_MAX_IRQ); ++gpio_irq) {
+		irq_set_chip_and_handler(gpio_irq, &ep93xx_gpio_irq_chip,
+					 handle_level_irq);
+		set_irq_flags(gpio_irq, IRQF_VALID);
+	}
+
+	irq_set_chained_handler(IRQ_EP93XX_GPIO_AB,
+				ep93xx_gpio_ab_irq_handler);
+	irq_set_chained_handler(IRQ_EP93XX_GPIO0MUX,
+				ep93xx_gpio_f_irq_handler);
+	irq_set_chained_handler(IRQ_EP93XX_GPIO1MUX,
+				ep93xx_gpio_f_irq_handler);
+	irq_set_chained_handler(IRQ_EP93XX_GPIO2MUX,
+				ep93xx_gpio_f_irq_handler);
+	irq_set_chained_handler(IRQ_EP93XX_GPIO3MUX,
+				ep93xx_gpio_f_irq_handler);
+	irq_set_chained_handler(IRQ_EP93XX_GPIO4MUX,
+				ep93xx_gpio_f_irq_handler);
+	irq_set_chained_handler(IRQ_EP93XX_GPIO5MUX,
+				ep93xx_gpio_f_irq_handler);
+	irq_set_chained_handler(IRQ_EP93XX_GPIO6MUX,
+				ep93xx_gpio_f_irq_handler);
+	irq_set_chained_handler(IRQ_EP93XX_GPIO7MUX,
+				ep93xx_gpio_f_irq_handler);
+}
+
+
+/*************************************************************************
+ * gpiolib interface for EP93xx on-chip GPIOs
+ *************************************************************************/
+struct ep93xx_gpio_bank {
+	const char	*label;
+	int		data;
+	int		dir;
+	int		base;
+	bool		has_debounce;
+};
+
+#define EP93XX_GPIO_BANK(_label, _data, _dir, _base, _debounce)	\
+	{							\
+		.label		= _label,			\
+		.data		= _data,			\
+		.dir		= _dir,				\
+		.base		= _base,			\
+		.has_debounce	= _debounce,			\
+	}
+
+static struct ep93xx_gpio_bank ep93xx_gpio_banks[] = {
+	EP93XX_GPIO_BANK("A", 0x00, 0x10, 0, true),
+	EP93XX_GPIO_BANK("B", 0x04, 0x14, 8, true),
+	EP93XX_GPIO_BANK("C", 0x08, 0x18, 40, false),
+	EP93XX_GPIO_BANK("D", 0x0c, 0x1c, 24, false),
+	EP93XX_GPIO_BANK("E", 0x20, 0x24, 32, false),
+	EP93XX_GPIO_BANK("F", 0x30, 0x34, 16, true),
+	EP93XX_GPIO_BANK("G", 0x38, 0x3c, 48, false),
+	EP93XX_GPIO_BANK("H", 0x40, 0x44, 56, false),
+};
+
+static int ep93xx_gpio_set_debounce(struct gpio_chip *chip,
+				    unsigned offset, unsigned debounce)
+{
+	int gpio = chip->base + offset;
+	int irq = gpio_to_irq(gpio);
+
+	if (irq < 0)
+		return -EINVAL;
+
+	ep93xx_gpio_int_debounce(irq, debounce ? true : false);
+
+	return 0;
+}
+
+static int ep93xx_gpio_add_bank(struct bgpio_chip *bgc, struct device *dev,
+	void __iomem *mmio_base, struct ep93xx_gpio_bank *bank)
+{
+	void __iomem *data = mmio_base + bank->data;
+	void __iomem *dir =  mmio_base + bank->dir;
+	int err;
+
+	err = bgpio_init(bgc, dev, 1, data, NULL, NULL, dir, NULL, false);
+	if (err)
+		return err;
+
+	bgc->gc.label = bank->label;
+	bgc->gc.base = bank->base;
+
+	if (bank->has_debounce)
+		bgc->gc.set_debounce = ep93xx_gpio_set_debounce;
+
+	return gpiochip_add(&bgc->gc);
+}
+
+static int __devinit ep93xx_gpio_probe(struct platform_device *pdev)
+{
+	struct ep93xx_gpio *ep93xx_gpio;
+	struct resource *res;
+	void __iomem *mmio;
+	int i;
+	int ret;
+
+	ep93xx_gpio = kzalloc(sizeof(*ep93xx_gpio), GFP_KERNEL);
+	if (!ep93xx_gpio)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		ret = -ENXIO;
+		goto exit_free;
+	}
+
+	if (!request_mem_region(res->start, resource_size(res), pdev->name)) {
+		ret = -EBUSY;
+		goto exit_free;
+	}
+
+	mmio = ioremap(res->start, resource_size(res));
+	if (!mmio) {
+		ret = -ENXIO;
+		goto exit_release;
+	}
+	ep93xx_gpio->mmio_base = mmio;
+
+	/* Default all ports to GPIO */
+	ep93xx_devcfg_set_bits(EP93XX_SYSCON_DEVCFG_KEYS |
+			       EP93XX_SYSCON_DEVCFG_GONK |
+			       EP93XX_SYSCON_DEVCFG_EONIDE |
+			       EP93XX_SYSCON_DEVCFG_GONIDE |
+			       EP93XX_SYSCON_DEVCFG_HONIDE);
+
+	for (i = 0; i < ARRAY_SIZE(ep93xx_gpio_banks); i++) {
+		struct bgpio_chip *bgc = &ep93xx_gpio->bgc[i];
+		struct ep93xx_gpio_bank *bank = &ep93xx_gpio_banks[i];
+
+		if (ep93xx_gpio_add_bank(bgc, &pdev->dev, mmio, bank))
+			dev_warn(&pdev->dev, "Unable to add gpio bank %s\n",
+				bank->label);
+	}
+
+	ep93xx_gpio_init_irq();
+
+	return 0;
+
+exit_release:
+	release_mem_region(res->start, resource_size(res));
+exit_free:
+	kfree(ep93xx_gpio);
+	dev_info(&pdev->dev, "%s failed with errno %d\n", __func__, ret);
+	return ret;
+}
+
+static struct platform_driver ep93xx_gpio_driver = {
+	.driver		= {
+		.name	= "gpio-ep93xx",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= ep93xx_gpio_probe,
+};
+
+static int __init ep93xx_gpio_init(void)
+{
+	return platform_driver_register(&ep93xx_gpio_driver);
+}
+postcore_initcall(ep93xx_gpio_init);
+
+MODULE_AUTHOR("Ryan Mallon <ryan@bluewatersys.com> "
+		"H Hartley Sweeten <hsweeten@visionengravers.com>");
+MODULE_DESCRIPTION("EP93XX GPIO driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/gpio/gpio-exynos4.c b/drivers/gpio/gpio-exynos4.c
index 9029835112e..d24b337cf1a 100644
--- a/drivers/gpio/gpio-exynos4.c
+++ b/drivers/gpio/gpio-exynos4.c
@@ -1,10 +1,9 @@
-/* linux/arch/arm/mach-exynos4/gpiolib.c
+/*
+ * EXYNOS4 - GPIOlib support
  *
  * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
  *
- * EXYNOS4 - GPIOlib support
- *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
diff --git a/drivers/gpio/basic_mmio_gpio.c b/drivers/gpio/gpio-generic.c
index 8152e9f516b..231714def4d 100644
--- a/drivers/gpio/basic_mmio_gpio.c
+++ b/drivers/gpio/gpio-generic.c
@@ -1,5 +1,5 @@
 /*
- * Driver for basic memory-mapped GPIO controllers.
+ * Generic driver for memory-mapped GPIO controllers.
  *
  * Copyright 2008 MontaVista Software, Inc.
  * Copyright 2008,2010 Anton Vorontsov <cbouatmailru@gmail.com>
@@ -404,7 +404,7 @@ int __devinit bgpio_init(struct bgpio_chip *bgc,
 }
 EXPORT_SYMBOL_GPL(bgpio_init);
 
-#ifdef CONFIG_GPIO_BASIC_MMIO
+#ifdef CONFIG_GPIO_GENERIC_PLATFORM
 
 static void __iomem *bgpio_map(struct platform_device *pdev,
 			       const char *name,
@@ -541,7 +541,7 @@ static void __exit bgpio_platform_exit(void)
 }
 module_exit(bgpio_platform_exit);
 
-#endif /* CONFIG_GPIO_BASIC_MMIO */
+#endif /* CONFIG_GPIO_GENERIC_PLATFORM */
 
 MODULE_DESCRIPTION("Driver for basic memory-mapped GPIO controllers");
 MODULE_AUTHOR("Anton Vorontsov <cbouatmailru@gmail.com>");
diff --git a/drivers/gpio/it8761e_gpio.c b/drivers/gpio/gpio-it8761e.c
index 48fc43c4bdd..278b8131701 100644
--- a/drivers/gpio/it8761e_gpio.c
+++ b/drivers/gpio/gpio-it8761e.c
@@ -1,5 +1,5 @@
 /*
- *  it8761_gpio.c - GPIO interface for IT8761E Super I/O chip
+ *  GPIO interface for IT8761E Super I/O chip
  *
  *  Author: Denis Turischev <denis@compulab.co.il>
  *
diff --git a/drivers/gpio/janz-ttl.c b/drivers/gpio/gpio-janz-ttl.c
index 813ac077e5d..813ac077e5d 100644
--- a/drivers/gpio/janz-ttl.c
+++ b/drivers/gpio/gpio-janz-ttl.c
diff --git a/drivers/gpio/langwell_gpio.c b/drivers/gpio/gpio-langwell.c
index 644ba1255d3..d2eb57c60e0 100644
--- a/drivers/gpio/langwell_gpio.c
+++ b/drivers/gpio/gpio-langwell.c
@@ -1,4 +1,6 @@
-/* langwell_gpio.c Moorestown platform Langwell chip GPIO driver
+/*
+ * Moorestown platform Langwell chip GPIO driver
+ *
  * Copyright (c) 2008 - 2009,  Intel Corporation.
  *
  * This program is free software; you can redistribute it and/or modify
diff --git a/drivers/gpio/max7300.c b/drivers/gpio/gpio-max7300.c
index 962f661c18c..a5ca0ab1b37 100644
--- a/drivers/gpio/max7300.c
+++ b/drivers/gpio/gpio-max7300.c
@@ -1,6 +1,4 @@
 /*
- * drivers/gpio/max7300.c
- *
  * Copyright (C) 2009 Wolfram Sang, Pengutronix
  *
  * This program is free software; you can redistribute it and/or modify
diff --git a/drivers/gpio/max7301.c b/drivers/gpio/gpio-max7301.c
index 92a100ddef6..741acfcbe76 100644
--- a/drivers/gpio/max7301.c
+++ b/drivers/gpio/gpio-max7301.c
@@ -1,6 +1,4 @@
 /*
- * drivers/gpio/max7301.c
- *
  * Copyright (C) 2006 Juergen Beisert, Pengutronix
  * Copyright (C) 2008 Guennadi Liakhovetski, Pengutronix
  * Copyright (C) 2009 Wolfram Sang, Pengutronix
diff --git a/drivers/gpio/max730x.c b/drivers/gpio/gpio-max730x.c
index 94ce773f95f..05e2dac60b3 100644
--- a/drivers/gpio/max730x.c
+++ b/drivers/gpio/gpio-max730x.c
@@ -1,6 +1,4 @@
 /**
- * drivers/gpio/max7301.c
- *
  * Copyright (C) 2006 Juergen Beisert, Pengutronix
  * Copyright (C) 2008 Guennadi Liakhovetski, Pengutronix
  * Copyright (C) 2009 Wolfram Sang, Pengutronix
diff --git a/drivers/gpio/max732x.c b/drivers/gpio/gpio-max732x.c
index ad6951edc16..9504120812a 100644
--- a/drivers/gpio/max732x.c
+++ b/drivers/gpio/gpio-max732x.c
@@ -1,5 +1,5 @@
 /*
- *  max732x.c - I2C Port Expander with 8/16 I/O
+ *  MAX732x I2C Port Expander with 8/16 I/O
  *
  *  Copyright (C) 2007 Marvell International Ltd.
  *  Copyright (C) 2008 Jack Ren <jack.ren@marvell.com>
diff --git a/drivers/gpio/mc33880.c b/drivers/gpio/gpio-mc33880.c
index 4ec797593bd..b3b4652e89e 100644
--- a/drivers/gpio/mc33880.c
+++ b/drivers/gpio/gpio-mc33880.c
@@ -1,5 +1,5 @@
 /*
- * mc33880.c MC33880 high-side/low-side switch GPIO driver
+ * MC33880 high-side/low-side switch GPIO driver
  * Copyright (c) 2009 Intel Corporation
  *
  * This program is free software; you can redistribute it and/or modify
diff --git a/drivers/gpio/mcp23s08.c b/drivers/gpio/gpio-mcp23s08.c
index 40e076083ec..1ef46e6c2a2 100644
--- a/drivers/gpio/mcp23s08.c
+++ b/drivers/gpio/gpio-mcp23s08.c
@@ -1,12 +1,12 @@
 /*
- * mcp23s08.c - SPI gpio expander driver
+ * MCP23S08 SPI/GPIO gpio expander driver
  */
 
 #include <linux/kernel.h>
 #include <linux/device.h>
-#include <linux/workqueue.h>
 #include <linux/mutex.h>
 #include <linux/gpio.h>
+#include <linux/i2c.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/mcp23s08.h>
 #include <linux/slab.h>
@@ -17,13 +17,13 @@
  */
 #define MCP_TYPE_S08	0
 #define MCP_TYPE_S17	1
+#define MCP_TYPE_008	2
+#define MCP_TYPE_017	3
 
 /* Registers are all 8 bits wide.
  *
  * The mcp23s17 has twice as many bits, and can be configured to work
  * with either 16 bit registers or with two adjacent 8 bit banks.
- *
- * Also, there are I2C versions of both chips.
  */
 #define MCP_IODIR	0x00		/* init/reset:  all ones */
 #define MCP_IPOL	0x01
@@ -51,7 +51,6 @@ struct mcp23s08_ops {
 };
 
 struct mcp23s08 {
-	struct spi_device	*spi;
 	u8			addr;
 
 	u16			cache[11];
@@ -60,9 +59,8 @@ struct mcp23s08 {
 
 	struct gpio_chip	chip;
 
-	struct work_struct	work;
-
 	const struct mcp23s08_ops	*ops;
+	void			*data; /* ops specific data */
 };
 
 /* A given spi_device can represent up to eight mcp23sxx chips
@@ -76,6 +74,74 @@ struct mcp23s08_driver_data {
 	struct mcp23s08		chip[];
 };
 
+/*----------------------------------------------------------------------*/
+
+#ifdef CONFIG_I2C
+
+static int mcp23008_read(struct mcp23s08 *mcp, unsigned reg)
+{
+	return i2c_smbus_read_byte_data(mcp->data, reg);
+}
+
+static int mcp23008_write(struct mcp23s08 *mcp, unsigned reg, unsigned val)
+{
+	return i2c_smbus_write_byte_data(mcp->data, reg, val);
+}
+
+static int
+mcp23008_read_regs(struct mcp23s08 *mcp, unsigned reg, u16 *vals, unsigned n)
+{
+	while (n--) {
+		int ret = mcp23008_read(mcp, reg++);
+		if (ret < 0)
+			return ret;
+		*vals++ = ret;
+	}
+
+	return 0;
+}
+
+static int mcp23017_read(struct mcp23s08 *mcp, unsigned reg)
+{
+	return i2c_smbus_read_word_data(mcp->data, reg << 1);
+}
+
+static int mcp23017_write(struct mcp23s08 *mcp, unsigned reg, unsigned val)
+{
+	return i2c_smbus_write_word_data(mcp->data, reg << 1, val);
+}
+
+static int
+mcp23017_read_regs(struct mcp23s08 *mcp, unsigned reg, u16 *vals, unsigned n)
+{
+	while (n--) {
+		int ret = mcp23017_read(mcp, reg++);
+		if (ret < 0)
+			return ret;
+		*vals++ = ret;
+	}
+
+	return 0;
+}
+
+static const struct mcp23s08_ops mcp23008_ops = {
+	.read		= mcp23008_read,
+	.write		= mcp23008_write,
+	.read_regs	= mcp23008_read_regs,
+};
+
+static const struct mcp23s08_ops mcp23017_ops = {
+	.read		= mcp23017_read,
+	.write		= mcp23017_write,
+	.read_regs	= mcp23017_read_regs,
+};
+
+#endif /* CONFIG_I2C */
+
+/*----------------------------------------------------------------------*/
+
+#ifdef CONFIG_SPI_MASTER
+
 static int mcp23s08_read(struct mcp23s08 *mcp, unsigned reg)
 {
 	u8	tx[2], rx[1];
@@ -83,7 +149,7 @@ static int mcp23s08_read(struct mcp23s08 *mcp, unsigned reg)
 
 	tx[0] = mcp->addr | 0x01;
 	tx[1] = reg;
-	status = spi_write_then_read(mcp->spi, tx, sizeof tx, rx, sizeof rx);
+	status = spi_write_then_read(mcp->data, tx, sizeof tx, rx, sizeof rx);
 	return (status < 0) ? status : rx[0];
 }
 
@@ -94,7 +160,7 @@ static int mcp23s08_write(struct mcp23s08 *mcp, unsigned reg, unsigned val)
 	tx[0] = mcp->addr;
 	tx[1] = reg;
 	tx[2] = val;
-	return spi_write_then_read(mcp->spi, tx, sizeof tx, NULL, 0);
+	return spi_write_then_read(mcp->data, tx, sizeof tx, NULL, 0);
 }
 
 static int
@@ -109,7 +175,7 @@ mcp23s08_read_regs(struct mcp23s08 *mcp, unsigned reg, u16 *vals, unsigned n)
 	tx[1] = reg;
 
 	tmp = (u8 *)vals;
-	status = spi_write_then_read(mcp->spi, tx, sizeof tx, tmp, n);
+	status = spi_write_then_read(mcp->data, tx, sizeof tx, tmp, n);
 	if (status >= 0) {
 		while (n--)
 			vals[n] = tmp[n]; /* expand to 16bit */
@@ -124,7 +190,7 @@ static int mcp23s17_read(struct mcp23s08 *mcp, unsigned reg)
 
 	tx[0] = mcp->addr | 0x01;
 	tx[1] = reg << 1;
-	status = spi_write_then_read(mcp->spi, tx, sizeof tx, rx, sizeof rx);
+	status = spi_write_then_read(mcp->data, tx, sizeof tx, rx, sizeof rx);
 	return (status < 0) ? status : (rx[0] | (rx[1] << 8));
 }
 
@@ -136,7 +202,7 @@ static int mcp23s17_write(struct mcp23s08 *mcp, unsigned reg, unsigned val)
 	tx[1] = reg << 1;
 	tx[2] = val;
 	tx[3] = val >> 8;
-	return spi_write_then_read(mcp->spi, tx, sizeof tx, NULL, 0);
+	return spi_write_then_read(mcp->data, tx, sizeof tx, NULL, 0);
 }
 
 static int
@@ -150,7 +216,7 @@ mcp23s17_read_regs(struct mcp23s08 *mcp, unsigned reg, u16 *vals, unsigned n)
 	tx[0] = mcp->addr | 0x01;
 	tx[1] = reg << 1;
 
-	status = spi_write_then_read(mcp->spi, tx, sizeof tx,
+	status = spi_write_then_read(mcp->data, tx, sizeof tx,
 				     (u8 *)vals, n * 2);
 	if (status >= 0) {
 		while (n--)
@@ -172,6 +238,7 @@ static const struct mcp23s08_ops mcp23s17_ops = {
 	.read_regs	= mcp23s17_read_regs,
 };
 
+#endif /* CONFIG_SPI_MASTER */
 
 /*----------------------------------------------------------------------*/
 
@@ -299,17 +366,16 @@ done:
 
 /*----------------------------------------------------------------------*/
 
-static int mcp23s08_probe_one(struct spi_device *spi, unsigned addr,
+static int mcp23s08_probe_one(struct mcp23s08 *mcp, struct device *dev,
+			      void *data, unsigned addr,
 			      unsigned type, unsigned base, unsigned pullups)
 {
-	struct mcp23s08_driver_data	*data = spi_get_drvdata(spi);
-	struct mcp23s08			*mcp = data->mcp[addr];
-	int				status;
+	int status;
 
 	mutex_init(&mcp->lock);
 
-	mcp->spi = spi;
-	mcp->addr = 0x40 | (addr << 1);
+	mcp->data = data;
+	mcp->addr = addr;
 
 	mcp->chip.direction_input = mcp23s08_direction_input;
 	mcp->chip.get = mcp23s08_get;
@@ -317,18 +383,43 @@ static int mcp23s08_probe_one(struct spi_device *spi, unsigned addr,
 	mcp->chip.set = mcp23s08_set;
 	mcp->chip.dbg_show = mcp23s08_dbg_show;
 
-	if (type == MCP_TYPE_S17) {
+	switch (type) {
+#ifdef CONFIG_SPI_MASTER
+	case MCP_TYPE_S08:
+		mcp->ops = &mcp23s08_ops;
+		mcp->chip.ngpio = 8;
+		mcp->chip.label = "mcp23s08";
+		break;
+
+	case MCP_TYPE_S17:
 		mcp->ops = &mcp23s17_ops;
 		mcp->chip.ngpio = 16;
 		mcp->chip.label = "mcp23s17";
-	} else {
-		mcp->ops = &mcp23s08_ops;
+		break;
+#endif /* CONFIG_SPI_MASTER */
+
+#ifdef CONFIG_I2C
+	case MCP_TYPE_008:
+		mcp->ops = &mcp23008_ops;
 		mcp->chip.ngpio = 8;
-		mcp->chip.label = "mcp23s08";
+		mcp->chip.label = "mcp23008";
+		break;
+
+	case MCP_TYPE_017:
+		mcp->ops = &mcp23017_ops;
+		mcp->chip.ngpio = 16;
+		mcp->chip.label = "mcp23017";
+		break;
+#endif /* CONFIG_I2C */
+
+	default:
+		dev_err(dev, "invalid device type (%d)\n", type);
+		return -EINVAL;
 	}
+
 	mcp->chip.base = base;
 	mcp->chip.can_sleep = 1;
-	mcp->chip.dev = &spi->dev;
+	mcp->chip.dev = dev;
 	mcp->chip.owner = THIS_MODULE;
 
 	/* verify MCP_IOCON.SEQOP = 0, so sequential reads work,
@@ -374,11 +465,98 @@ static int mcp23s08_probe_one(struct spi_device *spi, unsigned addr,
 	status = gpiochip_add(&mcp->chip);
 fail:
 	if (status < 0)
-		dev_dbg(&spi->dev, "can't setup chip %d, --> %d\n",
-				addr, status);
+		dev_dbg(dev, "can't setup chip %d, --> %d\n",
+			addr, status);
 	return status;
 }
 
+/*----------------------------------------------------------------------*/
+
+#ifdef CONFIG_I2C
+
+static int __devinit mcp230xx_probe(struct i2c_client *client,
+				    const struct i2c_device_id *id)
+{
+	struct mcp23s08_platform_data *pdata;
+	struct mcp23s08 *mcp;
+	int status;
+
+	pdata = client->dev.platform_data;
+	if (!pdata || !gpio_is_valid(pdata->base)) {
+		dev_dbg(&client->dev, "invalid or missing platform data\n");
+		return -EINVAL;
+	}
+
+	mcp = kzalloc(sizeof *mcp, GFP_KERNEL);
+	if (!mcp)
+		return -ENOMEM;
+
+	status = mcp23s08_probe_one(mcp, &client->dev, client, client->addr,
+				    id->driver_data, pdata->base,
+				    pdata->chip[0].pullups);
+	if (status)
+		goto fail;
+
+	i2c_set_clientdata(client, mcp);
+
+	return 0;
+
+fail:
+	kfree(mcp);
+
+	return status;
+}
+
+static int __devexit mcp230xx_remove(struct i2c_client *client)
+{
+	struct mcp23s08 *mcp = i2c_get_clientdata(client);
+	int status;
+
+	status = gpiochip_remove(&mcp->chip);
+	if (status == 0)
+		kfree(mcp);
+
+	return status;
+}
+
+static const struct i2c_device_id mcp230xx_id[] = {
+	{ "mcp23008", MCP_TYPE_008 },
+	{ "mcp23017", MCP_TYPE_017 },
+	{ },
+};
+MODULE_DEVICE_TABLE(i2c, mcp230xx_id);
+
+static struct i2c_driver mcp230xx_driver = {
+	.driver = {
+		.name	= "mcp230xx",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= mcp230xx_probe,
+	.remove		= __devexit_p(mcp230xx_remove),
+	.id_table	= mcp230xx_id,
+};
+
+static int __init mcp23s08_i2c_init(void)
+{
+	return i2c_add_driver(&mcp230xx_driver);
+}
+
+static void mcp23s08_i2c_exit(void)
+{
+	i2c_del_driver(&mcp230xx_driver);
+}
+
+#else
+
+static int __init mcp23s08_i2c_init(void) { return 0; }
+static void mcp23s08_i2c_exit(void) { }
+
+#endif /* CONFIG_I2C */
+
+/*----------------------------------------------------------------------*/
+
+#ifdef CONFIG_SPI_MASTER
+
 static int mcp23s08_probe(struct spi_device *spi)
 {
 	struct mcp23s08_platform_data	*pdata;
@@ -421,7 +599,8 @@ static int mcp23s08_probe(struct spi_device *spi)
 			continue;
 		chips--;
 		data->mcp[addr] = &data->chip[chips];
-		status = mcp23s08_probe_one(spi, addr, type, base,
+		status = mcp23s08_probe_one(data->mcp[addr], &spi->dev, spi,
+					    0x40 | (addr << 1), type, base,
 					    pdata->chip[addr].pullups);
 		if (status < 0)
 			goto fail;
@@ -435,14 +614,6 @@ static int mcp23s08_probe(struct spi_device *spi)
 	 * handled here...
 	 */
 
-	if (pdata->setup) {
-		status = pdata->setup(spi,
-				pdata->base, data->ngpio,
-				pdata->context);
-		if (status < 0)
-			dev_dbg(&spi->dev, "setup --> %d\n", status);
-	}
-
 	return 0;
 
 fail:
@@ -462,20 +633,9 @@ fail:
 static int mcp23s08_remove(struct spi_device *spi)
 {
 	struct mcp23s08_driver_data	*data = spi_get_drvdata(spi);
-	struct mcp23s08_platform_data	*pdata = spi->dev.platform_data;
 	unsigned			addr;
 	int				status = 0;
 
-	if (pdata->teardown) {
-		status = pdata->teardown(spi,
-				pdata->base, data->ngpio,
-				pdata->context);
-		if (status < 0) {
-			dev_err(&spi->dev, "%s --> %d\n", "teardown", status);
-			return status;
-		}
-	}
-
 	for (addr = 0; addr < ARRAY_SIZE(data->mcp); addr++) {
 		int tmp;
 
@@ -510,20 +670,53 @@ static struct spi_driver mcp23s08_driver = {
 	},
 };
 
+static int __init mcp23s08_spi_init(void)
+{
+	return spi_register_driver(&mcp23s08_driver);
+}
+
+static void mcp23s08_spi_exit(void)
+{
+	spi_unregister_driver(&mcp23s08_driver);
+}
+
+#else
+
+static int __init mcp23s08_spi_init(void) { return 0; }
+static void mcp23s08_spi_exit(void) { }
+
+#endif /* CONFIG_SPI_MASTER */
+
 /*----------------------------------------------------------------------*/
 
 static int __init mcp23s08_init(void)
 {
-	return spi_register_driver(&mcp23s08_driver);
+	int ret;
+
+	ret = mcp23s08_spi_init();
+	if (ret)
+		goto spi_fail;
+
+	ret = mcp23s08_i2c_init();
+	if (ret)
+		goto i2c_fail;
+
+	return 0;
+
+ i2c_fail:
+	mcp23s08_spi_exit();
+ spi_fail:
+	return ret;
 }
-/* register after spi postcore initcall and before
+/* register after spi/i2c postcore initcall and before
  * subsys initcalls that may rely on these GPIOs
  */
 subsys_initcall(mcp23s08_init);
 
 static void __exit mcp23s08_exit(void)
 {
-	spi_unregister_driver(&mcp23s08_driver);
+	mcp23s08_spi_exit();
+	mcp23s08_i2c_exit();
 }
 module_exit(mcp23s08_exit);
 
diff --git a/drivers/gpio/ml_ioh_gpio.c b/drivers/gpio/gpio-ml-ioh.c
index 1bc621ac353..a9016f56ed7 100644
--- a/drivers/gpio/ml_ioh_gpio.c
+++ b/drivers/gpio/gpio-ml-ioh.c
@@ -233,7 +233,7 @@ static int __devinit ioh_gpio_probe(struct pci_dev *pdev,
 	return 0;
 
 err_gpiochip_add:
-	for (; i != 0; i--) {
+	while (--i >= 0) {
 		chip--;
 		ret = gpiochip_remove(&chip->gpio);
 		if (ret)
diff --git a/drivers/gpio/gpio-mpc5200.c b/drivers/gpio/gpio-mpc5200.c
new file mode 100644
index 00000000000..52d3ed20810
--- /dev/null
+++ b/drivers/gpio/gpio-mpc5200.c
@@ -0,0 +1,376 @@
+/*
+ * MPC52xx gpio driver
+ *
+ * Copyright (c) 2008 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/of.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/of_gpio.h>
+#include <linux/io.h>
+#include <linux/of_platform.h>
+
+#include <asm/gpio.h>
+#include <asm/mpc52xx.h>
+#include <sysdev/fsl_soc.h>
+
+static DEFINE_SPINLOCK(gpio_lock);
+
+struct mpc52xx_gpiochip {
+	struct of_mm_gpio_chip mmchip;
+	unsigned int shadow_dvo;
+	unsigned int shadow_gpioe;
+	unsigned int shadow_ddr;
+};
+
+/*
+ * GPIO LIB API implementation for wakeup GPIOs.
+ *
+ * There's a maximum of 8 wakeup GPIOs. Which of these are available
+ * for use depends on your board setup.
+ *
+ * 0 -> GPIO_WKUP_7
+ * 1 -> GPIO_WKUP_6
+ * 2 -> PSC6_1
+ * 3 -> PSC6_0
+ * 4 -> ETH_17
+ * 5 -> PSC3_9
+ * 6 -> PSC2_4
+ * 7 -> PSC1_4
+ *
+ */
+static int mpc52xx_wkup_gpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct mpc52xx_gpio_wkup __iomem *regs = mm_gc->regs;
+	unsigned int ret;
+
+	ret = (in_8(&regs->wkup_ival) >> (7 - gpio)) & 1;
+
+	pr_debug("%s: gpio: %d ret: %d\n", __func__, gpio, ret);
+
+	return ret;
+}
+
+static inline void
+__mpc52xx_wkup_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct mpc52xx_gpiochip *chip = container_of(mm_gc,
+			struct mpc52xx_gpiochip, mmchip);
+	struct mpc52xx_gpio_wkup __iomem *regs = mm_gc->regs;
+
+	if (val)
+		chip->shadow_dvo |= 1 << (7 - gpio);
+	else
+		chip->shadow_dvo &= ~(1 << (7 - gpio));
+
+	out_8(&regs->wkup_dvo, chip->shadow_dvo);
+}
+
+static void
+mpc52xx_wkup_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&gpio_lock, flags);
+
+	__mpc52xx_wkup_gpio_set(gc, gpio, val);
+
+	spin_unlock_irqrestore(&gpio_lock, flags);
+
+	pr_debug("%s: gpio: %d val: %d\n", __func__, gpio, val);
+}
+
+static int mpc52xx_wkup_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct mpc52xx_gpiochip *chip = container_of(mm_gc,
+			struct mpc52xx_gpiochip, mmchip);
+	struct mpc52xx_gpio_wkup __iomem *regs = mm_gc->regs;
+	unsigned long flags;
+
+	spin_lock_irqsave(&gpio_lock, flags);
+
+	/* set the direction */
+	chip->shadow_ddr &= ~(1 << (7 - gpio));
+	out_8(&regs->wkup_ddr, chip->shadow_ddr);
+
+	/* and enable the pin */
+	chip->shadow_gpioe |= 1 << (7 - gpio);
+	out_8(&regs->wkup_gpioe, chip->shadow_gpioe);
+
+	spin_unlock_irqrestore(&gpio_lock, flags);
+
+	return 0;
+}
+
+static int
+mpc52xx_wkup_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct mpc52xx_gpio_wkup __iomem *regs = mm_gc->regs;
+	struct mpc52xx_gpiochip *chip = container_of(mm_gc,
+			struct mpc52xx_gpiochip, mmchip);
+	unsigned long flags;
+
+	spin_lock_irqsave(&gpio_lock, flags);
+
+	__mpc52xx_wkup_gpio_set(gc, gpio, val);
+
+	/* Then set direction */
+	chip->shadow_ddr |= 1 << (7 - gpio);
+	out_8(&regs->wkup_ddr, chip->shadow_ddr);
+
+	/* Finally enable the pin */
+	chip->shadow_gpioe |= 1 << (7 - gpio);
+	out_8(&regs->wkup_gpioe, chip->shadow_gpioe);
+
+	spin_unlock_irqrestore(&gpio_lock, flags);
+
+	pr_debug("%s: gpio: %d val: %d\n", __func__, gpio, val);
+
+	return 0;
+}
+
+static int __devinit mpc52xx_wkup_gpiochip_probe(struct platform_device *ofdev)
+{
+	struct mpc52xx_gpiochip *chip;
+	struct mpc52xx_gpio_wkup __iomem *regs;
+	struct gpio_chip *gc;
+	int ret;
+
+	chip = kzalloc(sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	gc = &chip->mmchip.gc;
+
+	gc->ngpio            = 8;
+	gc->direction_input  = mpc52xx_wkup_gpio_dir_in;
+	gc->direction_output = mpc52xx_wkup_gpio_dir_out;
+	gc->get              = mpc52xx_wkup_gpio_get;
+	gc->set              = mpc52xx_wkup_gpio_set;
+
+	ret = of_mm_gpiochip_add(ofdev->dev.of_node, &chip->mmchip);
+	if (ret)
+		return ret;
+
+	regs = chip->mmchip.regs;
+	chip->shadow_gpioe = in_8(&regs->wkup_gpioe);
+	chip->shadow_ddr = in_8(&regs->wkup_ddr);
+	chip->shadow_dvo = in_8(&regs->wkup_dvo);
+
+	return 0;
+}
+
+static int mpc52xx_gpiochip_remove(struct platform_device *ofdev)
+{
+	return -EBUSY;
+}
+
+static const struct of_device_id mpc52xx_wkup_gpiochip_match[] = {
+	{ .compatible = "fsl,mpc5200-gpio-wkup", },
+	{}
+};
+
+static struct platform_driver mpc52xx_wkup_gpiochip_driver = {
+	.driver = {
+		.name = "mpc5200-gpio-wkup",
+		.owner = THIS_MODULE,
+		.of_match_table = mpc52xx_wkup_gpiochip_match,
+	},
+	.probe = mpc52xx_wkup_gpiochip_probe,
+	.remove = mpc52xx_gpiochip_remove,
+};
+
+/*
+ * GPIO LIB API implementation for simple GPIOs
+ *
+ * There's a maximum of 32 simple GPIOs. Which of these are available
+ * for use depends on your board setup.
+ * The numbering reflects the bit numbering in the port registers:
+ *
+ *  0..1  > reserved
+ *  2..3  > IRDA
+ *  4..7  > ETHR
+ *  8..11 > reserved
+ * 12..15 > USB
+ * 16..17 > reserved
+ * 18..23 > PSC3
+ * 24..27 > PSC2
+ * 28..31 > PSC1
+ */
+static int mpc52xx_simple_gpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct mpc52xx_gpio __iomem *regs = mm_gc->regs;
+	unsigned int ret;
+
+	ret = (in_be32(&regs->simple_ival) >> (31 - gpio)) & 1;
+
+	return ret;
+}
+
+static inline void
+__mpc52xx_simple_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct mpc52xx_gpiochip *chip = container_of(mm_gc,
+			struct mpc52xx_gpiochip, mmchip);
+	struct mpc52xx_gpio __iomem *regs = mm_gc->regs;
+
+	if (val)
+		chip->shadow_dvo |= 1 << (31 - gpio);
+	else
+		chip->shadow_dvo &= ~(1 << (31 - gpio));
+	out_be32(&regs->simple_dvo, chip->shadow_dvo);
+}
+
+static void
+mpc52xx_simple_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&gpio_lock, flags);
+
+	__mpc52xx_simple_gpio_set(gc, gpio, val);
+
+	spin_unlock_irqrestore(&gpio_lock, flags);
+
+	pr_debug("%s: gpio: %d val: %d\n", __func__, gpio, val);
+}
+
+static int mpc52xx_simple_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct mpc52xx_gpiochip *chip = container_of(mm_gc,
+			struct mpc52xx_gpiochip, mmchip);
+	struct mpc52xx_gpio __iomem *regs = mm_gc->regs;
+	unsigned long flags;
+
+	spin_lock_irqsave(&gpio_lock, flags);
+
+	/* set the direction */
+	chip->shadow_ddr &= ~(1 << (31 - gpio));
+	out_be32(&regs->simple_ddr, chip->shadow_ddr);
+
+	/* and enable the pin */
+	chip->shadow_gpioe |= 1 << (31 - gpio);
+	out_be32(&regs->simple_gpioe, chip->shadow_gpioe);
+
+	spin_unlock_irqrestore(&gpio_lock, flags);
+
+	return 0;
+}
+
+static int
+mpc52xx_simple_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+	struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
+	struct mpc52xx_gpiochip *chip = container_of(mm_gc,
+			struct mpc52xx_gpiochip, mmchip);
+	struct mpc52xx_gpio __iomem *regs = mm_gc->regs;
+	unsigned long flags;
+
+	spin_lock_irqsave(&gpio_lock, flags);
+
+	/* First set initial value */
+	__mpc52xx_simple_gpio_set(gc, gpio, val);
+
+	/* Then set direction */
+	chip->shadow_ddr |= 1 << (31 - gpio);
+	out_be32(&regs->simple_ddr, chip->shadow_ddr);
+
+	/* Finally enable the pin */
+	chip->shadow_gpioe |= 1 << (31 - gpio);
+	out_be32(&regs->simple_gpioe, chip->shadow_gpioe);
+
+	spin_unlock_irqrestore(&gpio_lock, flags);
+
+	pr_debug("%s: gpio: %d val: %d\n", __func__, gpio, val);
+
+	return 0;
+}
+
+static int __devinit mpc52xx_simple_gpiochip_probe(struct platform_device *ofdev)
+{
+	struct mpc52xx_gpiochip *chip;
+	struct gpio_chip *gc;
+	struct mpc52xx_gpio __iomem *regs;
+	int ret;
+
+	chip = kzalloc(sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	gc = &chip->mmchip.gc;
+
+	gc->ngpio            = 32;
+	gc->direction_input  = mpc52xx_simple_gpio_dir_in;
+	gc->direction_output = mpc52xx_simple_gpio_dir_out;
+	gc->get              = mpc52xx_simple_gpio_get;
+	gc->set              = mpc52xx_simple_gpio_set;
+
+	ret = of_mm_gpiochip_add(ofdev->dev.of_node, &chip->mmchip);
+	if (ret)
+		return ret;
+
+	regs = chip->mmchip.regs;
+	chip->shadow_gpioe = in_be32(&regs->simple_gpioe);
+	chip->shadow_ddr = in_be32(&regs->simple_ddr);
+	chip->shadow_dvo = in_be32(&regs->simple_dvo);
+
+	return 0;
+}
+
+static const struct of_device_id mpc52xx_simple_gpiochip_match[] = {
+	{ .compatible = "fsl,mpc5200-gpio", },
+	{}
+};
+
+static struct platform_driver mpc52xx_simple_gpiochip_driver = {
+	.driver = {
+		.name = "mpc5200-gpio",
+		.owner = THIS_MODULE,
+		.of_match_table = mpc52xx_simple_gpiochip_match,
+	},
+	.probe = mpc52xx_simple_gpiochip_probe,
+	.remove = mpc52xx_gpiochip_remove,
+};
+
+static int __init mpc52xx_gpio_init(void)
+{
+	if (platform_driver_register(&mpc52xx_wkup_gpiochip_driver))
+		printk(KERN_ERR "Unable to register wakeup GPIO driver\n");
+
+	if (platform_driver_register(&mpc52xx_simple_gpiochip_driver))
+		printk(KERN_ERR "Unable to register simple GPIO driver\n");
+
+	return 0;
+}
+
+
+/* Make sure we get initialised before anyone else tries to use us */
+subsys_initcall(mpc52xx_gpio_init);
+
+/* No exit call at the moment as we cannot unregister of gpio chips */
+
+MODULE_DESCRIPTION("Freescale MPC52xx gpio driver");
+MODULE_AUTHOR("Sascha Hauer <s.hauer@pengutronix.de");
+MODULE_LICENSE("GPL v2");
+
diff --git a/drivers/gpio/gpio-mxc.c b/drivers/gpio/gpio-mxc.c
new file mode 100644
index 00000000000..4340acae3bd
--- /dev/null
+++ b/drivers/gpio/gpio-mxc.c
@@ -0,0 +1,460 @@
+/*
+ * MXC GPIO support. (c) 2008 Daniel Mack <daniel@caiaq.de>
+ * Copyright 2008 Juergen Beisert, kernel@pengutronix.de
+ *
+ * Based on code from Freescale,
+ * Copyright (C) 2004-2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/basic_mmio_gpio.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <asm-generic/bug.h>
+
+enum mxc_gpio_hwtype {
+	IMX1_GPIO,	/* runs on i.mx1 */
+	IMX21_GPIO,	/* runs on i.mx21 and i.mx27 */
+	IMX31_GPIO,	/* runs on all other i.mx */
+};
+
+/* device type dependent stuff */
+struct mxc_gpio_hwdata {
+	unsigned dr_reg;
+	unsigned gdir_reg;
+	unsigned psr_reg;
+	unsigned icr1_reg;
+	unsigned icr2_reg;
+	unsigned imr_reg;
+	unsigned isr_reg;
+	unsigned low_level;
+	unsigned high_level;
+	unsigned rise_edge;
+	unsigned fall_edge;
+};
+
+struct mxc_gpio_port {
+	struct list_head node;
+	void __iomem *base;
+	int irq;
+	int irq_high;
+	int virtual_irq_start;
+	struct bgpio_chip bgc;
+	u32 both_edges;
+};
+
+static struct mxc_gpio_hwdata imx1_imx21_gpio_hwdata = {
+	.dr_reg		= 0x1c,
+	.gdir_reg	= 0x00,
+	.psr_reg	= 0x24,
+	.icr1_reg	= 0x28,
+	.icr2_reg	= 0x2c,
+	.imr_reg	= 0x30,
+	.isr_reg	= 0x34,
+	.low_level	= 0x03,
+	.high_level	= 0x02,
+	.rise_edge	= 0x00,
+	.fall_edge	= 0x01,
+};
+
+static struct mxc_gpio_hwdata imx31_gpio_hwdata = {
+	.dr_reg		= 0x00,
+	.gdir_reg	= 0x04,
+	.psr_reg	= 0x08,
+	.icr1_reg	= 0x0c,
+	.icr2_reg	= 0x10,
+	.imr_reg	= 0x14,
+	.isr_reg	= 0x18,
+	.low_level	= 0x00,
+	.high_level	= 0x01,
+	.rise_edge	= 0x02,
+	.fall_edge	= 0x03,
+};
+
+static enum mxc_gpio_hwtype mxc_gpio_hwtype;
+static struct mxc_gpio_hwdata *mxc_gpio_hwdata;
+
+#define GPIO_DR			(mxc_gpio_hwdata->dr_reg)
+#define GPIO_GDIR		(mxc_gpio_hwdata->gdir_reg)
+#define GPIO_PSR		(mxc_gpio_hwdata->psr_reg)
+#define GPIO_ICR1		(mxc_gpio_hwdata->icr1_reg)
+#define GPIO_ICR2		(mxc_gpio_hwdata->icr2_reg)
+#define GPIO_IMR		(mxc_gpio_hwdata->imr_reg)
+#define GPIO_ISR		(mxc_gpio_hwdata->isr_reg)
+
+#define GPIO_INT_LOW_LEV	(mxc_gpio_hwdata->low_level)
+#define GPIO_INT_HIGH_LEV	(mxc_gpio_hwdata->high_level)
+#define GPIO_INT_RISE_EDGE	(mxc_gpio_hwdata->rise_edge)
+#define GPIO_INT_FALL_EDGE	(mxc_gpio_hwdata->fall_edge)
+#define GPIO_INT_NONE		0x4
+
+static struct platform_device_id mxc_gpio_devtype[] = {
+	{
+		.name = "imx1-gpio",
+		.driver_data = IMX1_GPIO,
+	}, {
+		.name = "imx21-gpio",
+		.driver_data = IMX21_GPIO,
+	}, {
+		.name = "imx31-gpio",
+		.driver_data = IMX31_GPIO,
+	}, {
+		/* sentinel */
+	}
+};
+
+static const struct of_device_id mxc_gpio_dt_ids[] = {
+	{ .compatible = "fsl,imx1-gpio", .data = &mxc_gpio_devtype[IMX1_GPIO], },
+	{ .compatible = "fsl,imx21-gpio", .data = &mxc_gpio_devtype[IMX21_GPIO], },
+	{ .compatible = "fsl,imx31-gpio", .data = &mxc_gpio_devtype[IMX31_GPIO], },
+	{ /* sentinel */ }
+};
+
+/*
+ * MX2 has one interrupt *for all* gpio ports. The list is used
+ * to save the references to all ports, so that mx2_gpio_irq_handler
+ * can walk through all interrupt status registers.
+ */
+static LIST_HEAD(mxc_gpio_ports);
+
+/* Note: This driver assumes 32 GPIOs are handled in one register */
+
+static int gpio_set_irq_type(struct irq_data *d, u32 type)
+{
+	u32 gpio = irq_to_gpio(d->irq);
+	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+	struct mxc_gpio_port *port = gc->private;
+	u32 bit, val;
+	int edge;
+	void __iomem *reg = port->base;
+
+	port->both_edges &= ~(1 << (gpio & 31));
+	switch (type) {
+	case IRQ_TYPE_EDGE_RISING:
+		edge = GPIO_INT_RISE_EDGE;
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		edge = GPIO_INT_FALL_EDGE;
+		break;
+	case IRQ_TYPE_EDGE_BOTH:
+		val = gpio_get_value(gpio);
+		if (val) {
+			edge = GPIO_INT_LOW_LEV;
+			pr_debug("mxc: set GPIO %d to low trigger\n", gpio);
+		} else {
+			edge = GPIO_INT_HIGH_LEV;
+			pr_debug("mxc: set GPIO %d to high trigger\n", gpio);
+		}
+		port->both_edges |= 1 << (gpio & 31);
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		edge = GPIO_INT_LOW_LEV;
+		break;
+	case IRQ_TYPE_LEVEL_HIGH:
+		edge = GPIO_INT_HIGH_LEV;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	reg += GPIO_ICR1 + ((gpio & 0x10) >> 2); /* lower or upper register */
+	bit = gpio & 0xf;
+	val = readl(reg) & ~(0x3 << (bit << 1));
+	writel(val | (edge << (bit << 1)), reg);
+	writel(1 << (gpio & 0x1f), port->base + GPIO_ISR);
+
+	return 0;
+}
+
+static void mxc_flip_edge(struct mxc_gpio_port *port, u32 gpio)
+{
+	void __iomem *reg = port->base;
+	u32 bit, val;
+	int edge;
+
+	reg += GPIO_ICR1 + ((gpio & 0x10) >> 2); /* lower or upper register */
+	bit = gpio & 0xf;
+	val = readl(reg);
+	edge = (val >> (bit << 1)) & 3;
+	val &= ~(0x3 << (bit << 1));
+	if (edge == GPIO_INT_HIGH_LEV) {
+		edge = GPIO_INT_LOW_LEV;
+		pr_debug("mxc: switch GPIO %d to low trigger\n", gpio);
+	} else if (edge == GPIO_INT_LOW_LEV) {
+		edge = GPIO_INT_HIGH_LEV;
+		pr_debug("mxc: switch GPIO %d to high trigger\n", gpio);
+	} else {
+		pr_err("mxc: invalid configuration for GPIO %d: %x\n",
+		       gpio, edge);
+		return;
+	}
+	writel(val | (edge << (bit << 1)), reg);
+}
+
+/* handle 32 interrupts in one status register */
+static void mxc_gpio_irq_handler(struct mxc_gpio_port *port, u32 irq_stat)
+{
+	u32 gpio_irq_no_base = port->virtual_irq_start;
+
+	while (irq_stat != 0) {
+		int irqoffset = fls(irq_stat) - 1;
+
+		if (port->both_edges & (1 << irqoffset))
+			mxc_flip_edge(port, irqoffset);
+
+		generic_handle_irq(gpio_irq_no_base + irqoffset);
+
+		irq_stat &= ~(1 << irqoffset);
+	}
+}
+
+/* MX1 and MX3 has one interrupt *per* gpio port */
+static void mx3_gpio_irq_handler(u32 irq, struct irq_desc *desc)
+{
+	u32 irq_stat;
+	struct mxc_gpio_port *port = irq_get_handler_data(irq);
+
+	irq_stat = readl(port->base + GPIO_ISR) & readl(port->base + GPIO_IMR);
+
+	mxc_gpio_irq_handler(port, irq_stat);
+}
+
+/* MX2 has one interrupt *for all* gpio ports */
+static void mx2_gpio_irq_handler(u32 irq, struct irq_desc *desc)
+{
+	u32 irq_msk, irq_stat;
+	struct mxc_gpio_port *port;
+
+	/* walk through all interrupt status registers */
+	list_for_each_entry(port, &mxc_gpio_ports, node) {
+		irq_msk = readl(port->base + GPIO_IMR);
+		if (!irq_msk)
+			continue;
+
+		irq_stat = readl(port->base + GPIO_ISR) & irq_msk;
+		if (irq_stat)
+			mxc_gpio_irq_handler(port, irq_stat);
+	}
+}
+
+/*
+ * Set interrupt number "irq" in the GPIO as a wake-up source.
+ * While system is running, all registered GPIO interrupts need to have
+ * wake-up enabled. When system is suspended, only selected GPIO interrupts
+ * need to have wake-up enabled.
+ * @param  irq          interrupt source number
+ * @param  enable       enable as wake-up if equal to non-zero
+ * @return       This function returns 0 on success.
+ */
+static int gpio_set_wake_irq(struct irq_data *d, u32 enable)
+{
+	u32 gpio = irq_to_gpio(d->irq);
+	u32 gpio_idx = gpio & 0x1F;
+	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+	struct mxc_gpio_port *port = gc->private;
+
+	if (enable) {
+		if (port->irq_high && (gpio_idx >= 16))
+			enable_irq_wake(port->irq_high);
+		else
+			enable_irq_wake(port->irq);
+	} else {
+		if (port->irq_high && (gpio_idx >= 16))
+			disable_irq_wake(port->irq_high);
+		else
+			disable_irq_wake(port->irq);
+	}
+
+	return 0;
+}
+
+static void __init mxc_gpio_init_gc(struct mxc_gpio_port *port)
+{
+	struct irq_chip_generic *gc;
+	struct irq_chip_type *ct;
+
+	gc = irq_alloc_generic_chip("gpio-mxc", 1, port->virtual_irq_start,
+				    port->base, handle_level_irq);
+	gc->private = port;
+
+	ct = gc->chip_types;
+	ct->chip.irq_ack = irq_gc_ack_set_bit;
+	ct->chip.irq_mask = irq_gc_mask_clr_bit;
+	ct->chip.irq_unmask = irq_gc_mask_set_bit;
+	ct->chip.irq_set_type = gpio_set_irq_type;
+	ct->chip.irq_set_wake = gpio_set_wake_irq;
+	ct->regs.ack = GPIO_ISR;
+	ct->regs.mask = GPIO_IMR;
+
+	irq_setup_generic_chip(gc, IRQ_MSK(32), IRQ_GC_INIT_NESTED_LOCK,
+			       IRQ_NOREQUEST, 0);
+}
+
+static void __devinit mxc_gpio_get_hw(struct platform_device *pdev)
+{
+	const struct of_device_id *of_id =
+			of_match_device(mxc_gpio_dt_ids, &pdev->dev);
+	enum mxc_gpio_hwtype hwtype;
+
+	if (of_id)
+		pdev->id_entry = of_id->data;
+	hwtype = pdev->id_entry->driver_data;
+
+	if (mxc_gpio_hwtype) {
+		/*
+		 * The driver works with a reasonable presupposition,
+		 * that is all gpio ports must be the same type when
+		 * running on one soc.
+		 */
+		BUG_ON(mxc_gpio_hwtype != hwtype);
+		return;
+	}
+
+	if (hwtype == IMX31_GPIO)
+		mxc_gpio_hwdata = &imx31_gpio_hwdata;
+	else
+		mxc_gpio_hwdata = &imx1_imx21_gpio_hwdata;
+
+	mxc_gpio_hwtype = hwtype;
+}
+
+static int __devinit mxc_gpio_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct mxc_gpio_port *port;
+	struct resource *iores;
+	int err;
+
+	mxc_gpio_get_hw(pdev);
+
+	port = kzalloc(sizeof(struct mxc_gpio_port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+
+	iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!iores) {
+		err = -ENODEV;
+		goto out_kfree;
+	}
+
+	if (!request_mem_region(iores->start, resource_size(iores),
+				pdev->name)) {
+		err = -EBUSY;
+		goto out_kfree;
+	}
+
+	port->base = ioremap(iores->start, resource_size(iores));
+	if (!port->base) {
+		err = -ENOMEM;
+		goto out_release_mem;
+	}
+
+	port->irq_high = platform_get_irq(pdev, 1);
+	port->irq = platform_get_irq(pdev, 0);
+	if (port->irq < 0) {
+		err = -EINVAL;
+		goto out_iounmap;
+	}
+
+	/* disable the interrupt and clear the status */
+	writel(0, port->base + GPIO_IMR);
+	writel(~0, port->base + GPIO_ISR);
+
+	if (mxc_gpio_hwtype == IMX21_GPIO) {
+		/* setup one handler for all GPIO interrupts */
+		if (pdev->id == 0)
+			irq_set_chained_handler(port->irq,
+						mx2_gpio_irq_handler);
+	} else {
+		/* setup one handler for each entry */
+		irq_set_chained_handler(port->irq, mx3_gpio_irq_handler);
+		irq_set_handler_data(port->irq, port);
+		if (port->irq_high > 0) {
+			/* setup handler for GPIO 16 to 31 */
+			irq_set_chained_handler(port->irq_high,
+						mx3_gpio_irq_handler);
+			irq_set_handler_data(port->irq_high, port);
+		}
+	}
+
+	err = bgpio_init(&port->bgc, &pdev->dev, 4,
+			 port->base + GPIO_PSR,
+			 port->base + GPIO_DR, NULL,
+			 port->base + GPIO_GDIR, NULL, false);
+	if (err)
+		goto out_iounmap;
+
+	port->bgc.gc.base = pdev->id * 32;
+	port->bgc.dir = port->bgc.read_reg(port->bgc.reg_dir);
+	port->bgc.data = port->bgc.read_reg(port->bgc.reg_set);
+
+	err = gpiochip_add(&port->bgc.gc);
+	if (err)
+		goto out_bgpio_remove;
+
+	/*
+	 * In dt case, we use gpio number range dynamically
+	 * allocated by gpio core.
+	 */
+	port->virtual_irq_start = MXC_GPIO_IRQ_START + (np ? port->bgc.gc.base :
+							     pdev->id * 32);
+
+	/* gpio-mxc can be a generic irq chip */
+	mxc_gpio_init_gc(port);
+
+	list_add_tail(&port->node, &mxc_gpio_ports);
+
+	return 0;
+
+out_bgpio_remove:
+	bgpio_remove(&port->bgc);
+out_iounmap:
+	iounmap(port->base);
+out_release_mem:
+	release_mem_region(iores->start, resource_size(iores));
+out_kfree:
+	kfree(port);
+	dev_info(&pdev->dev, "%s failed with errno %d\n", __func__, err);
+	return err;
+}
+
+static struct platform_driver mxc_gpio_driver = {
+	.driver		= {
+		.name	= "gpio-mxc",
+		.owner	= THIS_MODULE,
+		.of_match_table = mxc_gpio_dt_ids,
+	},
+	.probe		= mxc_gpio_probe,
+	.id_table	= mxc_gpio_devtype,
+};
+
+static int __init gpio_mxc_init(void)
+{
+	return platform_driver_register(&mxc_gpio_driver);
+}
+postcore_initcall(gpio_mxc_init);
+
+MODULE_AUTHOR("Freescale Semiconductor, "
+	      "Daniel Mack <danielncaiaq.de>, "
+	      "Juergen Beisert <kernel@pengutronix.de>");
+MODULE_DESCRIPTION("Freescale MXC GPIO");
+MODULE_LICENSE("GPL");
diff --git a/drivers/gpio/gpio-mxs.c b/drivers/gpio/gpio-mxs.c
new file mode 100644
index 00000000000..af55a8577c2
--- /dev/null
+++ b/drivers/gpio/gpio-mxs.c
@@ -0,0 +1,289 @@
+/*
+ * MXC GPIO support. (c) 2008 Daniel Mack <daniel@caiaq.de>
+ * Copyright 2008 Juergen Beisert, kernel@pengutronix.de
+ *
+ * Based on code from Freescale,
+ * Copyright (C) 2004-2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA  02110-1301, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/basic_mmio_gpio.h>
+#include <mach/mxs.h>
+
+#define MXS_SET		0x4
+#define MXS_CLR		0x8
+
+#define PINCTRL_DOUT(n)		((cpu_is_mx23() ? 0x0500 : 0x0700) + (n) * 0x10)
+#define PINCTRL_DIN(n)		((cpu_is_mx23() ? 0x0600 : 0x0900) + (n) * 0x10)
+#define PINCTRL_DOE(n)		((cpu_is_mx23() ? 0x0700 : 0x0b00) + (n) * 0x10)
+#define PINCTRL_PIN2IRQ(n)	((cpu_is_mx23() ? 0x0800 : 0x1000) + (n) * 0x10)
+#define PINCTRL_IRQEN(n)	((cpu_is_mx23() ? 0x0900 : 0x1100) + (n) * 0x10)
+#define PINCTRL_IRQLEV(n)	((cpu_is_mx23() ? 0x0a00 : 0x1200) + (n) * 0x10)
+#define PINCTRL_IRQPOL(n)	((cpu_is_mx23() ? 0x0b00 : 0x1300) + (n) * 0x10)
+#define PINCTRL_IRQSTAT(n)	((cpu_is_mx23() ? 0x0c00 : 0x1400) + (n) * 0x10)
+
+#define GPIO_INT_FALL_EDGE	0x0
+#define GPIO_INT_LOW_LEV	0x1
+#define GPIO_INT_RISE_EDGE	0x2
+#define GPIO_INT_HIGH_LEV	0x3
+#define GPIO_INT_LEV_MASK	(1 << 0)
+#define GPIO_INT_POL_MASK	(1 << 1)
+
+struct mxs_gpio_port {
+	void __iomem *base;
+	int id;
+	int irq;
+	int virtual_irq_start;
+	struct bgpio_chip bgc;
+};
+
+/* Note: This driver assumes 32 GPIOs are handled in one register */
+
+static int mxs_gpio_set_irq_type(struct irq_data *d, unsigned int type)
+{
+	u32 gpio = irq_to_gpio(d->irq);
+	u32 pin_mask = 1 << (gpio & 31);
+	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+	struct mxs_gpio_port *port = gc->private;
+	void __iomem *pin_addr;
+	int edge;
+
+	switch (type) {
+	case IRQ_TYPE_EDGE_RISING:
+		edge = GPIO_INT_RISE_EDGE;
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		edge = GPIO_INT_FALL_EDGE;
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		edge = GPIO_INT_LOW_LEV;
+		break;
+	case IRQ_TYPE_LEVEL_HIGH:
+		edge = GPIO_INT_HIGH_LEV;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/* set level or edge */
+	pin_addr = port->base + PINCTRL_IRQLEV(port->id);
+	if (edge & GPIO_INT_LEV_MASK)
+		writel(pin_mask, pin_addr + MXS_SET);
+	else
+		writel(pin_mask, pin_addr + MXS_CLR);
+
+	/* set polarity */
+	pin_addr = port->base + PINCTRL_IRQPOL(port->id);
+	if (edge & GPIO_INT_POL_MASK)
+		writel(pin_mask, pin_addr + MXS_SET);
+	else
+		writel(pin_mask, pin_addr + MXS_CLR);
+
+	writel(1 << (gpio & 0x1f),
+	       port->base + PINCTRL_IRQSTAT(port->id) + MXS_CLR);
+
+	return 0;
+}
+
+/* MXS has one interrupt *per* gpio port */
+static void mxs_gpio_irq_handler(u32 irq, struct irq_desc *desc)
+{
+	u32 irq_stat;
+	struct mxs_gpio_port *port = irq_get_handler_data(irq);
+	u32 gpio_irq_no_base = port->virtual_irq_start;
+
+	desc->irq_data.chip->irq_ack(&desc->irq_data);
+
+	irq_stat = readl(port->base + PINCTRL_IRQSTAT(port->id)) &
+			readl(port->base + PINCTRL_IRQEN(port->id));
+
+	while (irq_stat != 0) {
+		int irqoffset = fls(irq_stat) - 1;
+		generic_handle_irq(gpio_irq_no_base + irqoffset);
+		irq_stat &= ~(1 << irqoffset);
+	}
+}
+
+/*
+ * Set interrupt number "irq" in the GPIO as a wake-up source.
+ * While system is running, all registered GPIO interrupts need to have
+ * wake-up enabled. When system is suspended, only selected GPIO interrupts
+ * need to have wake-up enabled.
+ * @param  irq          interrupt source number
+ * @param  enable       enable as wake-up if equal to non-zero
+ * @return       This function returns 0 on success.
+ */
+static int mxs_gpio_set_wake_irq(struct irq_data *d, unsigned int enable)
+{
+	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+	struct mxs_gpio_port *port = gc->private;
+
+	if (enable)
+		enable_irq_wake(port->irq);
+	else
+		disable_irq_wake(port->irq);
+
+	return 0;
+}
+
+static void __init mxs_gpio_init_gc(struct mxs_gpio_port *port)
+{
+	struct irq_chip_generic *gc;
+	struct irq_chip_type *ct;
+
+	gc = irq_alloc_generic_chip("gpio-mxs", 1, port->virtual_irq_start,
+				    port->base, handle_level_irq);
+	gc->private = port;
+
+	ct = gc->chip_types;
+	ct->chip.irq_ack = irq_gc_ack_set_bit;
+	ct->chip.irq_mask = irq_gc_mask_clr_bit;
+	ct->chip.irq_unmask = irq_gc_mask_set_bit;
+	ct->chip.irq_set_type = mxs_gpio_set_irq_type;
+	ct->chip.irq_set_wake = mxs_gpio_set_wake_irq;
+	ct->regs.ack = PINCTRL_IRQSTAT(port->id) + MXS_CLR;
+	ct->regs.mask = PINCTRL_IRQEN(port->id);
+
+	irq_setup_generic_chip(gc, IRQ_MSK(32), 0, IRQ_NOREQUEST, 0);
+}
+
+static int mxs_gpio_to_irq(struct gpio_chip *gc, unsigned offset)
+{
+	struct bgpio_chip *bgc = to_bgpio_chip(gc);
+	struct mxs_gpio_port *port =
+		container_of(bgc, struct mxs_gpio_port, bgc);
+
+	return port->virtual_irq_start + offset;
+}
+
+static int __devinit mxs_gpio_probe(struct platform_device *pdev)
+{
+	static void __iomem *base;
+	struct mxs_gpio_port *port;
+	struct resource *iores = NULL;
+	int err;
+
+	port = kzalloc(sizeof(struct mxs_gpio_port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+
+	port->id = pdev->id;
+	port->virtual_irq_start = MXS_GPIO_IRQ_START + port->id * 32;
+
+	/*
+	 * map memory region only once, as all the gpio ports
+	 * share the same one
+	 */
+	if (!base) {
+		iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		if (!iores) {
+			err = -ENODEV;
+			goto out_kfree;
+		}
+
+		if (!request_mem_region(iores->start, resource_size(iores),
+					pdev->name)) {
+			err = -EBUSY;
+			goto out_kfree;
+		}
+
+		base = ioremap(iores->start, resource_size(iores));
+		if (!base) {
+			err = -ENOMEM;
+			goto out_release_mem;
+		}
+	}
+	port->base = base;
+
+	port->irq = platform_get_irq(pdev, 0);
+	if (port->irq < 0) {
+		err = -EINVAL;
+		goto out_iounmap;
+	}
+
+	/*
+	 * select the pin interrupt functionality but initially
+	 * disable the interrupts
+	 */
+	writel(~0U, port->base + PINCTRL_PIN2IRQ(port->id));
+	writel(0, port->base + PINCTRL_IRQEN(port->id));
+
+	/* clear address has to be used to clear IRQSTAT bits */
+	writel(~0U, port->base + PINCTRL_IRQSTAT(port->id) + MXS_CLR);
+
+	/* gpio-mxs can be a generic irq chip */
+	mxs_gpio_init_gc(port);
+
+	/* setup one handler for each entry */
+	irq_set_chained_handler(port->irq, mxs_gpio_irq_handler);
+	irq_set_handler_data(port->irq, port);
+
+	err = bgpio_init(&port->bgc, &pdev->dev, 4,
+			 port->base + PINCTRL_DIN(port->id),
+			 port->base + PINCTRL_DOUT(port->id), NULL,
+			 port->base + PINCTRL_DOE(port->id), NULL, false);
+	if (err)
+		goto out_iounmap;
+
+	port->bgc.gc.to_irq = mxs_gpio_to_irq;
+	port->bgc.gc.base = port->id * 32;
+
+	err = gpiochip_add(&port->bgc.gc);
+	if (err)
+		goto out_bgpio_remove;
+
+	return 0;
+
+out_bgpio_remove:
+	bgpio_remove(&port->bgc);
+out_iounmap:
+	if (iores)
+		iounmap(port->base);
+out_release_mem:
+	if (iores)
+		release_mem_region(iores->start, resource_size(iores));
+out_kfree:
+	kfree(port);
+	dev_info(&pdev->dev, "%s failed with errno %d\n", __func__, err);
+	return err;
+}
+
+static struct platform_driver mxs_gpio_driver = {
+	.driver		= {
+		.name	= "gpio-mxs",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= mxs_gpio_probe,
+};
+
+static int __init mxs_gpio_init(void)
+{
+	return platform_driver_register(&mxs_gpio_driver);
+}
+postcore_initcall(mxs_gpio_init);
+
+MODULE_AUTHOR("Freescale Semiconductor, "
+	      "Daniel Mack <danielncaiaq.de>, "
+	      "Juergen Beisert <kernel@pengutronix.de>");
+MODULE_DESCRIPTION("Freescale MXS GPIO");
+MODULE_LICENSE("GPL");
diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index 35bebde23e8..0599854e221 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -54,6 +54,11 @@ struct gpio_bank {
 	struct device *dev;
 	bool dbck_flag;
 	int stride;
+	u32 width;
+
+	void (*set_dataout)(struct gpio_bank *bank, int gpio, int enable);
+
+	struct omap_gpio_reg_offs *regs;
 };
 
 #ifdef CONFIG_ARCH_OMAP3
@@ -79,121 +84,18 @@ static struct omap3_gpio_regs gpio_context[OMAP34XX_NR_GPIOS];
  */
 static struct gpio_bank *gpio_bank;
 
-static int bank_width;
-
 /* TODO: Analyze removing gpio_bank_count usage from driver code */
 int gpio_bank_count;
 
-static inline struct gpio_bank *get_gpio_bank(int gpio)
-{
-	if (cpu_is_omap15xx()) {
-		if (OMAP_GPIO_IS_MPUIO(gpio))
-			return &gpio_bank[0];
-		return &gpio_bank[1];
-	}
-	if (cpu_is_omap16xx()) {
-		if (OMAP_GPIO_IS_MPUIO(gpio))
-			return &gpio_bank[0];
-		return &gpio_bank[1 + (gpio >> 4)];
-	}
-	if (cpu_is_omap7xx()) {
-		if (OMAP_GPIO_IS_MPUIO(gpio))
-			return &gpio_bank[0];
-		return &gpio_bank[1 + (gpio >> 5)];
-	}
-	if (cpu_is_omap24xx())
-		return &gpio_bank[gpio >> 5];
-	if (cpu_is_omap34xx() || cpu_is_omap44xx())
-		return &gpio_bank[gpio >> 5];
-	BUG();
-	return NULL;
-}
-
-static inline int get_gpio_index(int gpio)
-{
-	if (cpu_is_omap7xx())
-		return gpio & 0x1f;
-	if (cpu_is_omap24xx())
-		return gpio & 0x1f;
-	if (cpu_is_omap34xx() || cpu_is_omap44xx())
-		return gpio & 0x1f;
-	return gpio & 0x0f;
-}
-
-static inline int gpio_valid(int gpio)
-{
-	if (gpio < 0)
-		return -1;
-	if (cpu_class_is_omap1() && OMAP_GPIO_IS_MPUIO(gpio)) {
-		if (gpio >= OMAP_MAX_GPIO_LINES + 16)
-			return -1;
-		return 0;
-	}
-	if (cpu_is_omap15xx() && gpio < 16)
-		return 0;
-	if ((cpu_is_omap16xx()) && gpio < 64)
-		return 0;
-	if (cpu_is_omap7xx() && gpio < 192)
-		return 0;
-	if (cpu_is_omap2420() && gpio < 128)
-		return 0;
-	if (cpu_is_omap2430() && gpio < 160)
-		return 0;
-	if ((cpu_is_omap34xx() || cpu_is_omap44xx()) && gpio < 192)
-		return 0;
-	return -1;
-}
-
-static int check_gpio(int gpio)
-{
-	if (unlikely(gpio_valid(gpio) < 0)) {
-		printk(KERN_ERR "omap-gpio: invalid GPIO %d\n", gpio);
-		dump_stack();
-		return -1;
-	}
-	return 0;
-}
+#define GPIO_INDEX(bank, gpio) (gpio % bank->width)
+#define GPIO_BIT(bank, gpio) (1 << GPIO_INDEX(bank, gpio))
 
 static void _set_gpio_direction(struct gpio_bank *bank, int gpio, int is_input)
 {
 	void __iomem *reg = bank->base;
 	u32 l;
 
-	switch (bank->method) {
-#ifdef CONFIG_ARCH_OMAP1
-	case METHOD_MPUIO:
-		reg += OMAP_MPUIO_IO_CNTL / bank->stride;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP15XX
-	case METHOD_GPIO_1510:
-		reg += OMAP1510_GPIO_DIR_CONTROL;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP16XX
-	case METHOD_GPIO_1610:
-		reg += OMAP1610_GPIO_DIRECTION;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
-	case METHOD_GPIO_7XX:
-		reg += OMAP7XX_GPIO_DIR_CONTROL;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
-	case METHOD_GPIO_24XX:
-		reg += OMAP24XX_GPIO_OE;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP4)
-	case METHOD_GPIO_44XX:
-		reg += OMAP4_GPIO_OE;
-		break;
-#endif
-	default:
-		WARN_ON(1);
-		return;
-	}
+	reg += bank->regs->direction;
 	l = __raw_readl(reg);
 	if (is_input)
 		l |= 1 << gpio;
@@ -202,165 +104,48 @@ static void _set_gpio_direction(struct gpio_bank *bank, int gpio, int is_input)
 	__raw_writel(l, reg);
 }
 
-static void _set_gpio_dataout(struct gpio_bank *bank, int gpio, int enable)
+
+/* set data out value using dedicate set/clear register */
+static void _set_gpio_dataout_reg(struct gpio_bank *bank, int gpio, int enable)
 {
 	void __iomem *reg = bank->base;
-	u32 l = 0;
+	u32 l = GPIO_BIT(bank, gpio);
+
+	if (enable)
+		reg += bank->regs->set_dataout;
+	else
+		reg += bank->regs->clr_dataout;
 
-	switch (bank->method) {
-#ifdef CONFIG_ARCH_OMAP1
-	case METHOD_MPUIO:
-		reg += OMAP_MPUIO_OUTPUT / bank->stride;
-		l = __raw_readl(reg);
-		if (enable)
-			l |= 1 << gpio;
-		else
-			l &= ~(1 << gpio);
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP15XX
-	case METHOD_GPIO_1510:
-		reg += OMAP1510_GPIO_DATA_OUTPUT;
-		l = __raw_readl(reg);
-		if (enable)
-			l |= 1 << gpio;
-		else
-			l &= ~(1 << gpio);
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP16XX
-	case METHOD_GPIO_1610:
-		if (enable)
-			reg += OMAP1610_GPIO_SET_DATAOUT;
-		else
-			reg += OMAP1610_GPIO_CLEAR_DATAOUT;
-		l = 1 << gpio;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
-	case METHOD_GPIO_7XX:
-		reg += OMAP7XX_GPIO_DATA_OUTPUT;
-		l = __raw_readl(reg);
-		if (enable)
-			l |= 1 << gpio;
-		else
-			l &= ~(1 << gpio);
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
-	case METHOD_GPIO_24XX:
-		if (enable)
-			reg += OMAP24XX_GPIO_SETDATAOUT;
-		else
-			reg += OMAP24XX_GPIO_CLEARDATAOUT;
-		l = 1 << gpio;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP4
-	case METHOD_GPIO_44XX:
-		if (enable)
-			reg += OMAP4_GPIO_SETDATAOUT;
-		else
-			reg += OMAP4_GPIO_CLEARDATAOUT;
-		l = 1 << gpio;
-		break;
-#endif
-	default:
-		WARN_ON(1);
-		return;
-	}
 	__raw_writel(l, reg);
 }
 
-static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
+/* set data out value using mask register */
+static void _set_gpio_dataout_mask(struct gpio_bank *bank, int gpio, int enable)
 {
-	void __iomem *reg;
+	void __iomem *reg = bank->base + bank->regs->dataout;
+	u32 gpio_bit = GPIO_BIT(bank, gpio);
+	u32 l;
 
-	if (check_gpio(gpio) < 0)
-		return -EINVAL;
-	reg = bank->base;
-	switch (bank->method) {
-#ifdef CONFIG_ARCH_OMAP1
-	case METHOD_MPUIO:
-		reg += OMAP_MPUIO_INPUT_LATCH / bank->stride;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP15XX
-	case METHOD_GPIO_1510:
-		reg += OMAP1510_GPIO_DATA_INPUT;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP16XX
-	case METHOD_GPIO_1610:
-		reg += OMAP1610_GPIO_DATAIN;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
-	case METHOD_GPIO_7XX:
-		reg += OMAP7XX_GPIO_DATA_INPUT;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
-	case METHOD_GPIO_24XX:
-		reg += OMAP24XX_GPIO_DATAIN;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP4
-	case METHOD_GPIO_44XX:
-		reg += OMAP4_GPIO_DATAIN;
-		break;
-#endif
-	default:
-		return -EINVAL;
-	}
-	return (__raw_readl(reg)
-			& (1 << get_gpio_index(gpio))) != 0;
+	l = __raw_readl(reg);
+	if (enable)
+		l |= gpio_bit;
+	else
+		l &= ~gpio_bit;
+	__raw_writel(l, reg);
 }
 
-static int _get_gpio_dataout(struct gpio_bank *bank, int gpio)
+static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
 {
-	void __iomem *reg;
+	void __iomem *reg = bank->base + bank->regs->datain;
 
-	if (check_gpio(gpio) < 0)
-		return -EINVAL;
-	reg = bank->base;
+	return (__raw_readl(reg) & GPIO_BIT(bank, gpio)) != 0;
+}
 
-	switch (bank->method) {
-#ifdef CONFIG_ARCH_OMAP1
-	case METHOD_MPUIO:
-		reg += OMAP_MPUIO_OUTPUT / bank->stride;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP15XX
-	case METHOD_GPIO_1510:
-		reg += OMAP1510_GPIO_DATA_OUTPUT;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP16XX
-	case METHOD_GPIO_1610:
-		reg += OMAP1610_GPIO_DATAOUT;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
-	case METHOD_GPIO_7XX:
-		reg += OMAP7XX_GPIO_DATA_OUTPUT;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
-	case METHOD_GPIO_24XX:
-		reg += OMAP24XX_GPIO_DATAOUT;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP4
-	case METHOD_GPIO_44XX:
-		reg += OMAP4_GPIO_DATAOUT;
-		break;
-#endif
-	default:
-		return -EINVAL;
-	}
+static int _get_gpio_dataout(struct gpio_bank *bank, int gpio)
+{
+	void __iomem *reg = bank->base + bank->regs->dataout;
 
-	return (__raw_readl(reg) & (1 << get_gpio_index(gpio))) != 0;
+	return (__raw_readl(reg) & GPIO_BIT(bank, gpio)) != 0;
 }
 
 #define MOD_REG_BIT(reg, bit_mask, set)	\
@@ -383,7 +168,7 @@ do {	\
 static void _set_gpio_debounce(struct gpio_bank *bank, unsigned gpio,
 		unsigned debounce)
 {
-	void __iomem		*reg = bank->base;
+	void __iomem		*reg;
 	u32			val;
 	u32			l;
 
@@ -397,21 +182,12 @@ static void _set_gpio_debounce(struct gpio_bank *bank, unsigned gpio,
 	else
 		debounce = (debounce / 0x1f) - 1;
 
-	l = 1 << get_gpio_index(gpio);
-
-	if (bank->method == METHOD_GPIO_44XX)
-		reg += OMAP4_GPIO_DEBOUNCINGTIME;
-	else
-		reg += OMAP24XX_GPIO_DEBOUNCE_VAL;
+	l = GPIO_BIT(bank, gpio);
 
+	reg = bank->base + bank->regs->debounce;
 	__raw_writel(debounce, reg);
 
-	reg = bank->base;
-	if (bank->method == METHOD_GPIO_44XX)
-		reg += OMAP4_GPIO_DEBOUNCENABLE;
-	else
-		reg += OMAP24XX_GPIO_DEBOUNCE_EN;
-
+	reg = bank->base + bank->regs->debounce_en;
 	val = __raw_readl(reg);
 
 	if (debounce) {
@@ -629,9 +405,6 @@ static int gpio_irq_type(struct irq_data *d, unsigned type)
 	else
 		gpio = d->irq - IH_GPIO_BASE;
 
-	if (check_gpio(gpio) < 0)
-		return -EINVAL;
-
 	if (type & ~IRQ_TYPE_SENSE_MASK)
 		return -EINVAL;
 
@@ -642,7 +415,7 @@ static int gpio_irq_type(struct irq_data *d, unsigned type)
 
 	bank = irq_data_get_irq_chip_data(d);
 	spin_lock_irqsave(&bank->lock, flags);
-	retval = _set_gpio_triggering(bank, get_gpio_index(gpio), type);
+	retval = _set_gpio_triggering(bank, GPIO_INDEX(bank, gpio), type);
 	spin_unlock_irqrestore(&bank->lock, flags);
 
 	if (type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH))
@@ -657,195 +430,81 @@ static void _clear_gpio_irqbank(struct gpio_bank *bank, int gpio_mask)
 {
 	void __iomem *reg = bank->base;
 
-	switch (bank->method) {
-#ifdef CONFIG_ARCH_OMAP1
-	case METHOD_MPUIO:
-		/* MPUIO irqstatus is reset by reading the status register,
-		 * so do nothing here */
-		return;
-#endif
-#ifdef CONFIG_ARCH_OMAP15XX
-	case METHOD_GPIO_1510:
-		reg += OMAP1510_GPIO_INT_STATUS;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP16XX
-	case METHOD_GPIO_1610:
-		reg += OMAP1610_GPIO_IRQSTATUS1;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
-	case METHOD_GPIO_7XX:
-		reg += OMAP7XX_GPIO_INT_STATUS;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
-	case METHOD_GPIO_24XX:
-		reg += OMAP24XX_GPIO_IRQSTATUS1;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP4)
-	case METHOD_GPIO_44XX:
-		reg += OMAP4_GPIO_IRQSTATUS0;
-		break;
-#endif
-	default:
-		WARN_ON(1);
-		return;
-	}
+	reg += bank->regs->irqstatus;
 	__raw_writel(gpio_mask, reg);
 
 	/* Workaround for clearing DSP GPIO interrupts to allow retention */
-	if (cpu_is_omap24xx() || cpu_is_omap34xx())
-		reg = bank->base + OMAP24XX_GPIO_IRQSTATUS2;
-	else if (cpu_is_omap44xx())
-		reg = bank->base + OMAP4_GPIO_IRQSTATUS1;
-
-	if (cpu_is_omap24xx() || cpu_is_omap34xx() || cpu_is_omap44xx()) {
+	if (bank->regs->irqstatus2) {
+		reg = bank->base + bank->regs->irqstatus2;
 		__raw_writel(gpio_mask, reg);
+	}
 
 	/* Flush posted write for the irq status to avoid spurious interrupts */
 	__raw_readl(reg);
-	}
 }
 
 static inline void _clear_gpio_irqstatus(struct gpio_bank *bank, int gpio)
 {
-	_clear_gpio_irqbank(bank, 1 << get_gpio_index(gpio));
+	_clear_gpio_irqbank(bank, GPIO_BIT(bank, gpio));
 }
 
 static u32 _get_gpio_irqbank_mask(struct gpio_bank *bank)
 {
 	void __iomem *reg = bank->base;
-	int inv = 0;
 	u32 l;
-	u32 mask;
-
-	switch (bank->method) {
-#ifdef CONFIG_ARCH_OMAP1
-	case METHOD_MPUIO:
-		reg += OMAP_MPUIO_GPIO_MASKIT / bank->stride;
-		mask = 0xffff;
-		inv = 1;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP15XX
-	case METHOD_GPIO_1510:
-		reg += OMAP1510_GPIO_INT_MASK;
-		mask = 0xffff;
-		inv = 1;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP16XX
-	case METHOD_GPIO_1610:
-		reg += OMAP1610_GPIO_IRQENABLE1;
-		mask = 0xffff;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
-	case METHOD_GPIO_7XX:
-		reg += OMAP7XX_GPIO_INT_MASK;
-		mask = 0xffffffff;
-		inv = 1;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
-	case METHOD_GPIO_24XX:
-		reg += OMAP24XX_GPIO_IRQENABLE1;
-		mask = 0xffffffff;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP4)
-	case METHOD_GPIO_44XX:
-		reg += OMAP4_GPIO_IRQSTATUSSET0;
-		mask = 0xffffffff;
-		break;
-#endif
-	default:
-		WARN_ON(1);
-		return 0;
-	}
+	u32 mask = (1 << bank->width) - 1;
 
+	reg += bank->regs->irqenable;
 	l = __raw_readl(reg);
-	if (inv)
+	if (bank->regs->irqenable_inv)
 		l = ~l;
 	l &= mask;
 	return l;
 }
 
-static void _enable_gpio_irqbank(struct gpio_bank *bank, int gpio_mask, int enable)
+static void _enable_gpio_irqbank(struct gpio_bank *bank, int gpio_mask)
 {
 	void __iomem *reg = bank->base;
 	u32 l;
 
-	switch (bank->method) {
-#ifdef CONFIG_ARCH_OMAP1
-	case METHOD_MPUIO:
-		reg += OMAP_MPUIO_GPIO_MASKIT / bank->stride;
-		l = __raw_readl(reg);
-		if (enable)
-			l &= ~(gpio_mask);
-		else
-			l |= gpio_mask;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP15XX
-	case METHOD_GPIO_1510:
-		reg += OMAP1510_GPIO_INT_MASK;
+	if (bank->regs->set_irqenable) {
+		reg += bank->regs->set_irqenable;
+		l = gpio_mask;
+	} else {
+		reg += bank->regs->irqenable;
 		l = __raw_readl(reg);
-		if (enable)
-			l &= ~(gpio_mask);
+		if (bank->regs->irqenable_inv)
+			l &= ~gpio_mask;
 		else
 			l |= gpio_mask;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP16XX
-	case METHOD_GPIO_1610:
-		if (enable)
-			reg += OMAP1610_GPIO_SET_IRQENABLE1;
-		else
-			reg += OMAP1610_GPIO_CLEAR_IRQENABLE1;
+	}
+
+	__raw_writel(l, reg);
+}
+
+static void _disable_gpio_irqbank(struct gpio_bank *bank, int gpio_mask)
+{
+	void __iomem *reg = bank->base;
+	u32 l;
+
+	if (bank->regs->clr_irqenable) {
+		reg += bank->regs->clr_irqenable;
 		l = gpio_mask;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
-	case METHOD_GPIO_7XX:
-		reg += OMAP7XX_GPIO_INT_MASK;
+	} else {
+		reg += bank->regs->irqenable;
 		l = __raw_readl(reg);
-		if (enable)
-			l &= ~(gpio_mask);
-		else
+		if (bank->regs->irqenable_inv)
 			l |= gpio_mask;
-		break;
-#endif
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
-	case METHOD_GPIO_24XX:
-		if (enable)
-			reg += OMAP24XX_GPIO_SETIRQENABLE1;
-		else
-			reg += OMAP24XX_GPIO_CLEARIRQENABLE1;
-		l = gpio_mask;
-		break;
-#endif
-#ifdef CONFIG_ARCH_OMAP4
-	case METHOD_GPIO_44XX:
-		if (enable)
-			reg += OMAP4_GPIO_IRQSTATUSSET0;
 		else
-			reg += OMAP4_GPIO_IRQSTATUSCLR0;
-		l = gpio_mask;
-		break;
-#endif
-	default:
-		WARN_ON(1);
-		return;
+			l &= ~gpio_mask;
 	}
+
 	__raw_writel(l, reg);
 }
 
 static inline void _set_gpio_irqenable(struct gpio_bank *bank, int gpio, int enable)
 {
-	_enable_gpio_irqbank(bank, 1 << get_gpio_index(gpio), enable);
+	_enable_gpio_irqbank(bank, GPIO_BIT(bank, gpio));
 }
 
 /*
@@ -858,50 +517,32 @@ static inline void _set_gpio_irqenable(struct gpio_bank *bank, int gpio, int ena
  */
 static int _set_gpio_wakeup(struct gpio_bank *bank, int gpio, int enable)
 {
-	unsigned long uninitialized_var(flags);
+	u32 gpio_bit = GPIO_BIT(bank, gpio);
+	unsigned long flags;
 
-	switch (bank->method) {
-#ifdef CONFIG_ARCH_OMAP16XX
-	case METHOD_MPUIO:
-	case METHOD_GPIO_1610:
-		spin_lock_irqsave(&bank->lock, flags);
-		if (enable)
-			bank->suspend_wakeup |= (1 << gpio);
-		else
-			bank->suspend_wakeup &= ~(1 << gpio);
-		spin_unlock_irqrestore(&bank->lock, flags);
-		return 0;
-#endif
-#ifdef CONFIG_ARCH_OMAP2PLUS
-	case METHOD_GPIO_24XX:
-	case METHOD_GPIO_44XX:
-		if (bank->non_wakeup_gpios & (1 << gpio)) {
-			printk(KERN_ERR "Unable to modify wakeup on "
-					"non-wakeup GPIO%d\n",
-					(bank - gpio_bank) * 32 + gpio);
-			return -EINVAL;
-		}
-		spin_lock_irqsave(&bank->lock, flags);
-		if (enable)
-			bank->suspend_wakeup |= (1 << gpio);
-		else
-			bank->suspend_wakeup &= ~(1 << gpio);
-		spin_unlock_irqrestore(&bank->lock, flags);
-		return 0;
-#endif
-	default:
-		printk(KERN_ERR "Can't enable GPIO wakeup for method %i\n",
-		       bank->method);
+	if (bank->non_wakeup_gpios & gpio_bit) {
+		dev_err(bank->dev, 
+			"Unable to modify wakeup on non-wakeup GPIO%d\n", gpio);
 		return -EINVAL;
 	}
+
+	spin_lock_irqsave(&bank->lock, flags);
+	if (enable)
+		bank->suspend_wakeup |= gpio_bit;
+	else
+		bank->suspend_wakeup &= ~gpio_bit;
+
+	spin_unlock_irqrestore(&bank->lock, flags);
+
+	return 0;
 }
 
 static void _reset_gpio(struct gpio_bank *bank, int gpio)
 {
-	_set_gpio_direction(bank, get_gpio_index(gpio), 1);
+	_set_gpio_direction(bank, GPIO_INDEX(bank, gpio), 1);
 	_set_gpio_irqenable(bank, gpio, 0);
 	_clear_gpio_irqstatus(bank, gpio);
-	_set_gpio_triggering(bank, get_gpio_index(gpio), IRQ_TYPE_NONE);
+	_set_gpio_triggering(bank, GPIO_INDEX(bank, gpio), IRQ_TYPE_NONE);
 }
 
 /* Use disable_irq_wake() and enable_irq_wake() functions from drivers */
@@ -911,10 +552,8 @@ static int gpio_wake_enable(struct irq_data *d, unsigned int enable)
 	struct gpio_bank *bank;
 	int retval;
 
-	if (check_gpio(gpio) < 0)
-		return -ENODEV;
 	bank = irq_data_get_irq_chip_data(d);
-	retval = _set_gpio_wakeup(bank, get_gpio_index(gpio), enable);
+	retval = _set_gpio_wakeup(bank, gpio, enable);
 
 	return retval;
 }
@@ -1030,31 +669,7 @@ static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
 	chained_irq_enter(chip, desc);
 
 	bank = irq_get_handler_data(irq);
-#ifdef CONFIG_ARCH_OMAP1
-	if (bank->method == METHOD_MPUIO)
-		isr_reg = bank->base +
-				OMAP_MPUIO_GPIO_INT / bank->stride;
-#endif
-#ifdef CONFIG_ARCH_OMAP15XX
-	if (bank->method == METHOD_GPIO_1510)
-		isr_reg = bank->base + OMAP1510_GPIO_INT_STATUS;
-#endif
-#if defined(CONFIG_ARCH_OMAP16XX)
-	if (bank->method == METHOD_GPIO_1610)
-		isr_reg = bank->base + OMAP1610_GPIO_IRQSTATUS1;
-#endif
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
-	if (bank->method == METHOD_GPIO_7XX)
-		isr_reg = bank->base + OMAP7XX_GPIO_INT_STATUS;
-#endif
-#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
-	if (bank->method == METHOD_GPIO_24XX)
-		isr_reg = bank->base + OMAP24XX_GPIO_IRQSTATUS1;
-#endif
-#if defined(CONFIG_ARCH_OMAP4)
-	if (bank->method == METHOD_GPIO_44XX)
-		isr_reg = bank->base + OMAP4_GPIO_IRQSTATUS0;
-#endif
+	isr_reg = bank->base + bank->regs->irqstatus;
 
 	if (WARN_ON(!isr_reg))
 		goto exit;
@@ -1076,9 +691,9 @@ static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
 		/* clear edge sensitive interrupts before handler(s) are
 		called so that we don't miss any interrupt occurred while
 		executing them */
-		_enable_gpio_irqbank(bank, isr_saved & ~level_mask, 0);
+		_disable_gpio_irqbank(bank, isr_saved & ~level_mask);
 		_clear_gpio_irqbank(bank, isr_saved & ~level_mask);
-		_enable_gpio_irqbank(bank, isr_saved & ~level_mask, 1);
+		_enable_gpio_irqbank(bank, isr_saved & ~level_mask);
 
 		/* if there is only edge sensitive GPIO pin interrupts
 		configured, we could unmask GPIO bank interrupt immediately */
@@ -1094,7 +709,7 @@ static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
 
 		gpio_irq = bank->virtual_irq_start;
 		for (; isr != 0; isr >>= 1, gpio_irq++) {
-			gpio_index = get_gpio_index(irq_to_gpio(gpio_irq));
+			gpio_index = GPIO_INDEX(bank, irq_to_gpio(gpio_irq));
 
 			if (!(isr & 1))
 				continue;
@@ -1150,7 +765,7 @@ static void gpio_mask_irq(struct irq_data *d)
 
 	spin_lock_irqsave(&bank->lock, flags);
 	_set_gpio_irqenable(bank, gpio, 0);
-	_set_gpio_triggering(bank, get_gpio_index(gpio), IRQ_TYPE_NONE);
+	_set_gpio_triggering(bank, GPIO_INDEX(bank, gpio), IRQ_TYPE_NONE);
 	spin_unlock_irqrestore(&bank->lock, flags);
 }
 
@@ -1158,13 +773,13 @@ static void gpio_unmask_irq(struct irq_data *d)
 {
 	unsigned int gpio = d->irq - IH_GPIO_BASE;
 	struct gpio_bank *bank = irq_data_get_irq_chip_data(d);
-	unsigned int irq_mask = 1 << get_gpio_index(gpio);
+	unsigned int irq_mask = GPIO_BIT(bank, gpio);
 	u32 trigger = irqd_get_trigger_type(d);
 	unsigned long flags;
 
 	spin_lock_irqsave(&bank->lock, flags);
 	if (trigger)
-		_set_gpio_triggering(bank, get_gpio_index(gpio), trigger);
+		_set_gpio_triggering(bank, GPIO_INDEX(bank, gpio), trigger);
 
 	/* For level-triggered GPIOs, the clearing must be done after
 	 * the HW source is cleared, thus after the handler has run */
@@ -1191,45 +806,8 @@ static struct irq_chip gpio_irq_chip = {
 
 #ifdef CONFIG_ARCH_OMAP1
 
-/* MPUIO uses the always-on 32k clock */
-
-static void mpuio_ack_irq(struct irq_data *d)
-{
-	/* The ISR is reset automatically, so do nothing here. */
-}
-
-static void mpuio_mask_irq(struct irq_data *d)
-{
-	unsigned int gpio = OMAP_MPUIO(d->irq - IH_MPUIO_BASE);
-	struct gpio_bank *bank = irq_data_get_irq_chip_data(d);
-
-	_set_gpio_irqenable(bank, gpio, 0);
-}
-
-static void mpuio_unmask_irq(struct irq_data *d)
-{
-	unsigned int gpio = OMAP_MPUIO(d->irq - IH_MPUIO_BASE);
-	struct gpio_bank *bank = irq_data_get_irq_chip_data(d);
-
-	_set_gpio_irqenable(bank, gpio, 1);
-}
-
-static struct irq_chip mpuio_irq_chip = {
-	.name		= "MPUIO",
-	.irq_ack	= mpuio_ack_irq,
-	.irq_mask	= mpuio_mask_irq,
-	.irq_unmask	= mpuio_unmask_irq,
-	.irq_set_type	= gpio_irq_type,
-#ifdef CONFIG_ARCH_OMAP16XX
-	/* REVISIT: assuming only 16xx supports MPUIO wake events */
-	.irq_set_wake	= gpio_wake_enable,
-#endif
-};
-
-
 #define bank_is_mpuio(bank)	((bank)->method == METHOD_MPUIO)
 
-
 #ifdef CONFIG_ARCH_OMAP16XX
 
 #include <linux/platform_device.h>
@@ -1289,7 +867,7 @@ static struct platform_device omap_mpuio_device = {
 
 static inline void mpuio_init(void)
 {
-	struct gpio_bank *bank = get_gpio_bank(OMAP_MPUIO(0));
+	struct gpio_bank *bank = &gpio_bank[0];
 	platform_set_drvdata(&omap_mpuio_device, bank);
 
 	if (platform_driver_register(&omap_mpuio_driver) == 0)
@@ -1302,8 +880,6 @@ static inline void mpuio_init(void) {}
 
 #else
 
-extern struct irq_chip mpuio_irq_chip;
-
 #define bank_is_mpuio(bank)	0
 static inline void mpuio_init(void) {}
 
@@ -1329,31 +905,8 @@ static int gpio_input(struct gpio_chip *chip, unsigned offset)
 
 static int gpio_is_input(struct gpio_bank *bank, int mask)
 {
-	void __iomem *reg = bank->base;
+	void __iomem *reg = bank->base + bank->regs->direction;
 
-	switch (bank->method) {
-	case METHOD_MPUIO:
-		reg += OMAP_MPUIO_IO_CNTL / bank->stride;
-		break;
-	case METHOD_GPIO_1510:
-		reg += OMAP1510_GPIO_DIR_CONTROL;
-		break;
-	case METHOD_GPIO_1610:
-		reg += OMAP1610_GPIO_DIRECTION;
-		break;
-	case METHOD_GPIO_7XX:
-		reg += OMAP7XX_GPIO_DIR_CONTROL;
-		break;
-	case METHOD_GPIO_24XX:
-		reg += OMAP24XX_GPIO_OE;
-		break;
-	case METHOD_GPIO_44XX:
-		reg += OMAP4_GPIO_OE;
-		break;
-	default:
-		WARN_ONCE(1, "gpio_is_input: incorrect OMAP GPIO method");
-		return -EINVAL;
-	}
 	return __raw_readl(reg) & mask;
 }
 
@@ -1365,9 +918,9 @@ static int gpio_get(struct gpio_chip *chip, unsigned offset)
 	u32 mask;
 
 	gpio = chip->base + offset;
-	bank = get_gpio_bank(gpio);
+	bank = container_of(chip, struct gpio_bank, chip);
 	reg = bank->base;
-	mask = 1 << get_gpio_index(gpio);
+	mask = GPIO_BIT(bank, gpio);
 
 	if (gpio_is_input(bank, mask))
 		return _get_gpio_datain(bank, gpio);
@@ -1382,7 +935,7 @@ static int gpio_output(struct gpio_chip *chip, unsigned offset, int value)
 
 	bank = container_of(chip, struct gpio_bank, chip);
 	spin_lock_irqsave(&bank->lock, flags);
-	_set_gpio_dataout(bank, offset, value);
+	bank->set_dataout(bank, offset, value);
 	_set_gpio_direction(bank, offset, 0);
 	spin_unlock_irqrestore(&bank->lock, flags);
 	return 0;
@@ -1416,7 +969,7 @@ static void gpio_set(struct gpio_chip *chip, unsigned offset, int value)
 
 	bank = container_of(chip, struct gpio_bank, chip);
 	spin_lock_irqsave(&bank->lock, flags);
-	_set_gpio_dataout(bank, offset, value);
+	bank->set_dataout(bank, offset, value);
 	spin_unlock_irqrestore(&bank->lock, flags);
 }
 
@@ -1432,19 +985,17 @@ static int gpio_2irq(struct gpio_chip *chip, unsigned offset)
 
 static void __init omap_gpio_show_rev(struct gpio_bank *bank)
 {
+	static bool called;
 	u32 rev;
 
-	if (cpu_is_omap16xx() && !(bank->method != METHOD_MPUIO))
-		rev = __raw_readw(bank->base + OMAP1610_GPIO_REVISION);
-	else if (cpu_is_omap24xx() || cpu_is_omap34xx())
-		rev = __raw_readl(bank->base + OMAP24XX_GPIO_REVISION);
-	else if (cpu_is_omap44xx())
-		rev = __raw_readl(bank->base + OMAP4_GPIO_REVISION);
-	else
+	if (called || bank->regs->revision == USHRT_MAX)
 		return;
 
-	printk(KERN_INFO "OMAP GPIO hardware version %d.%d\n",
+	rev = __raw_readw(bank->base + bank->regs->revision);
+	pr_info("OMAP GPIO hardware version %d.%d\n",
 		(rev >> 4) & 0x0f, rev & 0x0f);
+
+	called = true;
 }
 
 /* This lock class tells lockdep that GPIO irqs are in a different
@@ -1526,6 +1077,30 @@ static void omap_gpio_mod_init(struct gpio_bank *bank, int id)
 	}
 }
 
+static __init void
+omap_mpuio_alloc_gc(struct gpio_bank *bank, unsigned int irq_start,
+		    unsigned int num)
+{
+	struct irq_chip_generic *gc;
+	struct irq_chip_type *ct;
+
+	gc = irq_alloc_generic_chip("MPUIO", 1, irq_start, bank->base,
+				    handle_simple_irq);
+	ct = gc->chip_types;
+
+	/* NOTE: No ack required, reading IRQ status clears it. */
+	ct->chip.irq_mask = irq_gc_mask_set_bit;
+	ct->chip.irq_unmask = irq_gc_mask_clr_bit;
+	ct->chip.irq_set_type = gpio_irq_type;
+	/* REVISIT: assuming only 16xx supports MPUIO wake events */
+	if (cpu_is_omap16xx())
+		ct->chip.irq_set_wake = gpio_wake_enable,
+
+	ct->regs.mask = OMAP_MPUIO_GPIO_INT / bank->stride;
+	irq_setup_generic_chip(gc, IRQ_MSK(num), IRQ_GC_INIT_MASK_CACHE,
+			       IRQ_NOREQUEST | IRQ_NOPROBE, 0);
+}
+
 static void __devinit omap_gpio_chip_init(struct gpio_bank *bank)
 {
 	int j;
@@ -1553,22 +1128,23 @@ static void __devinit omap_gpio_chip_init(struct gpio_bank *bank)
 	} else {
 		bank->chip.label = "gpio";
 		bank->chip.base = gpio;
-		gpio += bank_width;
+		gpio += bank->width;
 	}
-	bank->chip.ngpio = bank_width;
+	bank->chip.ngpio = bank->width;
 
 	gpiochip_add(&bank->chip);
 
 	for (j = bank->virtual_irq_start;
-		     j < bank->virtual_irq_start + bank_width; j++) {
+		     j < bank->virtual_irq_start + bank->width; j++) {
 		irq_set_lockdep_class(j, &gpio_lock_class);
 		irq_set_chip_data(j, bank);
-		if (bank_is_mpuio(bank))
-			irq_set_chip(j, &mpuio_irq_chip);
-		else
+		if (bank_is_mpuio(bank)) {
+			omap_mpuio_alloc_gc(bank, j, bank->width);
+		} else {
 			irq_set_chip(j, &gpio_irq_chip);
-		irq_set_handler(j, handle_simple_irq);
-		set_irq_flags(j, IRQF_VALID);
+			irq_set_handler(j, handle_simple_irq);
+			set_irq_flags(j, IRQF_VALID);
+		}
 	}
 	irq_set_chained_handler(bank->irq, gpio_irq_handler);
 	irq_set_handler_data(bank->irq, bank);
@@ -1610,7 +1186,14 @@ static int __devinit omap_gpio_probe(struct platform_device *pdev)
 	bank->dev = &pdev->dev;
 	bank->dbck_flag = pdata->dbck_flag;
 	bank->stride = pdata->bank_stride;
-	bank_width = pdata->bank_width;
+	bank->width = pdata->bank_width;
+
+	bank->regs = pdata->regs;
+
+	if (bank->regs->set_dataout && bank->regs->clr_dataout)
+		bank->set_dataout = _set_gpio_dataout_reg;
+	else
+		bank->set_dataout = _set_gpio_dataout_mask;
 
 	spin_lock_init(&bank->lock);
 
diff --git a/drivers/gpio/pca953x.c b/drivers/gpio/gpio-pca953x.c
index 0451d7ac94a..c43b8ff626a 100644
--- a/drivers/gpio/pca953x.c
+++ b/drivers/gpio/gpio-pca953x.c
@@ -1,5 +1,5 @@
 /*
- *  pca953x.c - 4/8/16 bit I/O ports
+ *  PCA953x 4/8/16 bit I/O ports
  *
  *  Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com>
  *  Copyright (C) 2007 Marvell International Ltd.
@@ -21,7 +21,6 @@
 #include <linux/slab.h>
 #ifdef CONFIG_OF_GPIO
 #include <linux/of_platform.h>
-#include <linux/of_gpio.h>
 #endif
 
 #define PCA953X_INPUT		0
@@ -85,7 +84,6 @@ struct pca953x_chip {
 #endif
 
 	struct i2c_client *client;
-	struct pca953x_platform_data *dyn_pdata;
 	struct gpio_chip gpio_chip;
 	const char *const *names;
 	int	chip_type;
@@ -437,7 +435,7 @@ static irqreturn_t pca953x_irq_handler(int irq, void *devid)
 
 	do {
 		level = __ffs(pending);
-		generic_handle_irq(level + chip->irq_base);
+		handle_nested_irq(level + chip->irq_base);
 
 		pending &= ~(1 << level);
 	} while (pending);
@@ -446,13 +444,13 @@ static irqreturn_t pca953x_irq_handler(int irq, void *devid)
 }
 
 static int pca953x_irq_setup(struct pca953x_chip *chip,
-			     const struct i2c_device_id *id)
+			     const struct i2c_device_id *id,
+			     int irq_base)
 {
 	struct i2c_client *client = chip->client;
-	struct pca953x_platform_data *pdata = client->dev.platform_data;
 	int ret, offset = 0;
 
-	if (pdata->irq_base != -1
+	if (irq_base != -1
 			&& (id->driver_data & PCA_INT)) {
 		int lvl;
 
@@ -474,15 +472,19 @@ static int pca953x_irq_setup(struct pca953x_chip *chip,
 		 * this purpose.
 		 */
 		chip->irq_stat &= chip->reg_direction;
-		chip->irq_base = pdata->irq_base;
 		mutex_init(&chip->irq_lock);
 
+		chip->irq_base = irq_alloc_descs(-1, irq_base, chip->gpio_chip.ngpio, -1);
+		if (chip->irq_base < 0)
+			goto out_failed;
+
 		for (lvl = 0; lvl < chip->gpio_chip.ngpio; lvl++) {
 			int irq = lvl + chip->irq_base;
 
+			irq_clear_status_flags(irq, IRQ_NOREQUEST);
 			irq_set_chip_data(irq, chip);
-			irq_set_chip_and_handler(irq, &pca953x_irq_chip,
-						 handle_simple_irq);
+			irq_set_chip(irq, &pca953x_irq_chip);
+			irq_set_nested_thread(irq, true);
 #ifdef CONFIG_ARM
 			set_irq_flags(irq, IRQF_VALID);
 #else
@@ -493,8 +495,7 @@ static int pca953x_irq_setup(struct pca953x_chip *chip,
 		ret = request_threaded_irq(client->irq,
 					   NULL,
 					   pca953x_irq_handler,
-					   IRQF_TRIGGER_RISING |
-					   IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+					   IRQF_TRIGGER_LOW | IRQF_ONESHOT,
 					   dev_name(&client->dev), chip);
 		if (ret) {
 			dev_err(&client->dev, "failed to request irq %d\n",
@@ -514,17 +515,19 @@ out_failed:
 
 static void pca953x_irq_teardown(struct pca953x_chip *chip)
 {
-	if (chip->irq_base != -1)
+	if (chip->irq_base != -1) {
+		irq_free_descs(chip->irq_base, chip->gpio_chip.ngpio);
 		free_irq(chip->client->irq, chip);
+	}
 }
 #else /* CONFIG_GPIO_PCA953X_IRQ */
 static int pca953x_irq_setup(struct pca953x_chip *chip,
-			     const struct i2c_device_id *id)
+			     const struct i2c_device_id *id,
+			     int irq_base)
 {
 	struct i2c_client *client = chip->client;
-	struct pca953x_platform_data *pdata = client->dev.platform_data;
 
-	if (pdata->irq_base != -1 && (id->driver_data & PCA_INT))
+	if (irq_base != -1 && (id->driver_data & PCA_INT))
 		dev_warn(&client->dev, "interrupt support not compiled in\n");
 
 	return 0;
@@ -541,46 +544,39 @@ static void pca953x_irq_teardown(struct pca953x_chip *chip)
 #ifdef CONFIG_OF_GPIO
 /*
  * Translate OpenFirmware node properties into platform_data
+ * WARNING: This is DEPRECATED and will be removed eventually!
  */
-static struct pca953x_platform_data *
-pca953x_get_alt_pdata(struct i2c_client *client)
+void
+pca953x_get_alt_pdata(struct i2c_client *client, int *gpio_base, int *invert)
 {
-	struct pca953x_platform_data *pdata;
 	struct device_node *node;
 	const __be32 *val;
 	int size;
 
 	node = client->dev.of_node;
 	if (node == NULL)
-		return NULL;
-
-	pdata = kzalloc(sizeof(struct pca953x_platform_data), GFP_KERNEL);
-	if (pdata == NULL) {
-		dev_err(&client->dev, "Unable to allocate platform_data\n");
-		return NULL;
-	}
+		return;
 
-	pdata->gpio_base = -1;
+	*gpio_base = -1;
 	val = of_get_property(node, "linux,gpio-base", &size);
+	WARN(val, "%s: device-tree property 'linux,gpio-base' is deprecated!", __func__);
 	if (val) {
 		if (size != sizeof(*val))
 			dev_warn(&client->dev, "%s: wrong linux,gpio-base\n",
 				 node->full_name);
 		else
-			pdata->gpio_base = be32_to_cpup(val);
+			*gpio_base = be32_to_cpup(val);
 	}
 
 	val = of_get_property(node, "polarity", NULL);
+	WARN(val, "%s: device-tree property 'polarity' is deprecated!", __func__);
 	if (val)
-		pdata->invert = *val;
-
-	return pdata;
+		*invert = *val;
 }
 #else
-static struct pca953x_platform_data *
-pca953x_get_alt_pdata(struct i2c_client *client)
+void
+pca953x_get_alt_pdata(struct i2c_client *client, int *gpio_base, int *invert)
 {
-	return NULL;
 }
 #endif
 
@@ -642,6 +638,7 @@ static int __devinit pca953x_probe(struct i2c_client *client,
 {
 	struct pca953x_platform_data *pdata;
 	struct pca953x_chip *chip;
+	int irq_base=0, invert=0;
 	int ret = 0;
 
 	chip = kzalloc(sizeof(struct pca953x_chip), GFP_KERNEL);
@@ -649,26 +646,22 @@ static int __devinit pca953x_probe(struct i2c_client *client,
 		return -ENOMEM;
 
 	pdata = client->dev.platform_data;
-	if (pdata == NULL) {
-		pdata = pca953x_get_alt_pdata(client);
-		/*
-		 * Unlike normal platform_data, this is allocated
-		 * dynamically and must be freed in the driver
-		 */
-		chip->dyn_pdata = pdata;
-	}
-
-	if (pdata == NULL) {
-		dev_dbg(&client->dev, "no platform data\n");
-		ret = -EINVAL;
-		goto out_failed;
+	if (pdata) {
+		irq_base = pdata->irq_base;
+		chip->gpio_start = pdata->gpio_base;
+		invert = pdata->invert;
+		chip->names = pdata->names;
+	} else {
+		pca953x_get_alt_pdata(client, &chip->gpio_start, &invert);
+#ifdef CONFIG_OF_GPIO
+		/* If I2C node has no interrupts property, disable GPIO interrupts */
+		if (of_find_property(client->dev.of_node, "interrupts", NULL) == NULL)
+			irq_base = -1;
+#endif
 	}
 
 	chip->client = client;
 
-	chip->gpio_start = pdata->gpio_base;
-
-	chip->names = pdata->names;
 	chip->chip_type = id->driver_data & (PCA953X_TYPE | PCA957X_TYPE);
 
 	mutex_init(&chip->i2c_lock);
@@ -679,13 +672,13 @@ static int __devinit pca953x_probe(struct i2c_client *client,
 	pca953x_setup_gpio(chip, id->driver_data & PCA_GPIO_MASK);
 
 	if (chip->chip_type == PCA953X_TYPE)
-		device_pca953x_init(chip, pdata->invert);
+		device_pca953x_init(chip, invert);
 	else if (chip->chip_type == PCA957X_TYPE)
-		device_pca957x_init(chip, pdata->invert);
+		device_pca957x_init(chip, invert);
 	else
 		goto out_failed;
 
-	ret = pca953x_irq_setup(chip, id);
+	ret = pca953x_irq_setup(chip, id, irq_base);
 	if (ret)
 		goto out_failed;
 
@@ -693,7 +686,7 @@ static int __devinit pca953x_probe(struct i2c_client *client,
 	if (ret)
 		goto out_failed_irq;
 
-	if (pdata->setup) {
+	if (pdata && pdata->setup) {
 		ret = pdata->setup(client, chip->gpio_chip.base,
 				chip->gpio_chip.ngpio, pdata->context);
 		if (ret < 0)
@@ -706,7 +699,6 @@ static int __devinit pca953x_probe(struct i2c_client *client,
 out_failed_irq:
 	pca953x_irq_teardown(chip);
 out_failed:
-	kfree(chip->dyn_pdata);
 	kfree(chip);
 	return ret;
 }
@@ -717,7 +709,7 @@ static int pca953x_remove(struct i2c_client *client)
 	struct pca953x_chip *chip = i2c_get_clientdata(client);
 	int ret = 0;
 
-	if (pdata->teardown) {
+	if (pdata && pdata->teardown) {
 		ret = pdata->teardown(client, chip->gpio_chip.base,
 				chip->gpio_chip.ngpio, pdata->context);
 		if (ret < 0) {
@@ -735,7 +727,6 @@ static int pca953x_remove(struct i2c_client *client)
 	}
 
 	pca953x_irq_teardown(chip);
-	kfree(chip->dyn_pdata);
 	kfree(chip);
 	return 0;
 }
diff --git a/drivers/gpio/pcf857x.c b/drivers/gpio/gpio-pcf857x.c
index 879b473aab5..7369fdda92b 100644
--- a/drivers/gpio/pcf857x.c
+++ b/drivers/gpio/gpio-pcf857x.c
@@ -1,5 +1,5 @@
 /*
- * pcf857x - driver for pcf857x, pca857x, and pca967x I2C GPIO expanders
+ * Driver for pcf857x, pca857x, and pca967x I2C GPIO expanders
  *
  * Copyright (C) 2007 David Brownell
  *
diff --git a/drivers/gpio/pch_gpio.c b/drivers/gpio/gpio-pch.c
index 36919e77c49..36919e77c49 100644
--- a/drivers/gpio/pch_gpio.c
+++ b/drivers/gpio/gpio-pch.c
diff --git a/drivers/gpio/pl061.c b/drivers/gpio/gpio-pl061.c
index 6fcb28cdd86..2c5a18f32bf 100644
--- a/drivers/gpio/pl061.c
+++ b/drivers/gpio/gpio-pl061.c
@@ -1,7 +1,5 @@
 /*
- *  linux/drivers/gpio/pl061.c
- *
- *  Copyright (C) 2008, 2009 Provigent Ltd.
+ * Copyright (C) 2008, 2009 Provigent Ltd.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
diff --git a/drivers/gpio/gpio-plat-samsung.c b/drivers/gpio/gpio-plat-samsung.c
index ea37c046178..ef67f1952a7 100644
--- a/drivers/gpio/gpio-plat-samsung.c
+++ b/drivers/gpio/gpio-plat-samsung.c
@@ -1,5 +1,4 @@
-/* arch/arm/plat-samsung/gpiolib.c
- *
+/*
  * Copyright 2008 Openmoko, Inc.
  * Copyright 2008 Simtec Electronics
  *      Ben Dooks <ben@simtec.co.uk>
diff --git a/drivers/gpio/rdc321x-gpio.c b/drivers/gpio/gpio-rdc321x.c
index 2762698e020..2762698e020 100644
--- a/drivers/gpio/rdc321x-gpio.c
+++ b/drivers/gpio/gpio-rdc321x.c
diff --git a/drivers/gpio/gpio-s5pc100.c b/drivers/gpio/gpio-s5pc100.c
index 2842394b28b..7f87b0c76e0 100644
--- a/drivers/gpio/gpio-s5pc100.c
+++ b/drivers/gpio/gpio-s5pc100.c
@@ -1,4 +1,5 @@
-/* linux/arch/arm/mach-s5pc100/gpiolib.c
+/*
+ * S5PC100 - GPIOlib support
  *
  * Copyright (c) 2010 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
@@ -6,8 +7,6 @@
  *  Copyright 2009 Samsung Electronics Co
  *  Kyungmin Park <kyungmin.park@samsung.com>
  *
- * S5PC100 - GPIOlib support
- *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
diff --git a/drivers/gpio/gpio-s5pv210.c b/drivers/gpio/gpio-s5pv210.c
index 1ba20a703e0..eb12f1602de 100644
--- a/drivers/gpio/gpio-s5pv210.c
+++ b/drivers/gpio/gpio-s5pv210.c
@@ -1,10 +1,9 @@
-/* linux/arch/arm/mach-s5pv210/gpiolib.c
+/*
+ * S5PV210 - GPIOlib support
  *
  * Copyright (c) 2010 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com/
  *
- * S5PV210 - GPIOlib support
- *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
diff --git a/drivers/gpio/sch_gpio.c b/drivers/gpio/gpio-sch.c
index 56060421cdf..16351584549 100644
--- a/drivers/gpio/sch_gpio.c
+++ b/drivers/gpio/gpio-sch.c
@@ -1,5 +1,5 @@
 /*
- *  sch_gpio.c - GPIO interface for Intel Poulsbo SCH
+ * GPIO interface for Intel Poulsbo SCH
  *
  *  Copyright (c) 2010 CompuLab Ltd
  *  Author: Denis Turischev <denis@compulab.co.il>
diff --git a/drivers/gpio/stmpe-gpio.c b/drivers/gpio/gpio-stmpe.c
index 4c980b57332..4c980b57332 100644
--- a/drivers/gpio/stmpe-gpio.c
+++ b/drivers/gpio/gpio-stmpe.c
diff --git a/drivers/gpio/sx150x.c b/drivers/gpio/gpio-sx150x.c
index a4f73534394..a4f73534394 100644
--- a/drivers/gpio/sx150x.c
+++ b/drivers/gpio/gpio-sx150x.c
diff --git a/drivers/gpio/tc3589x-gpio.c b/drivers/gpio/gpio-tc3589x.c
index 2a82e8999a4..2a82e8999a4 100644
--- a/drivers/gpio/tc3589x-gpio.c
+++ b/drivers/gpio/gpio-tc3589x.c
diff --git a/drivers/gpio/gpio-tegra.c b/drivers/gpio/gpio-tegra.c
new file mode 100644
index 00000000000..747eb40e8af
--- /dev/null
+++ b/drivers/gpio/gpio-tegra.c
@@ -0,0 +1,441 @@
+/*
+ * arch/arm/mach-tegra/gpio.c
+ *
+ * Copyright (c) 2010 Google, Inc
+ *
+ * Author:
+ *	Erik Gilling <konkers@google.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/of.h>
+
+#include <asm/mach/irq.h>
+
+#include <mach/iomap.h>
+#include <mach/suspend.h>
+
+#define GPIO_BANK(x)		((x) >> 5)
+#define GPIO_PORT(x)		(((x) >> 3) & 0x3)
+#define GPIO_BIT(x)		((x) & 0x7)
+
+#define GPIO_REG(x)		(IO_TO_VIRT(TEGRA_GPIO_BASE) +	\
+				 GPIO_BANK(x) * 0x80 +		\
+				 GPIO_PORT(x) * 4)
+
+#define GPIO_CNF(x)		(GPIO_REG(x) + 0x00)
+#define GPIO_OE(x)		(GPIO_REG(x) + 0x10)
+#define GPIO_OUT(x)		(GPIO_REG(x) + 0X20)
+#define GPIO_IN(x)		(GPIO_REG(x) + 0x30)
+#define GPIO_INT_STA(x)		(GPIO_REG(x) + 0x40)
+#define GPIO_INT_ENB(x)		(GPIO_REG(x) + 0x50)
+#define GPIO_INT_LVL(x)		(GPIO_REG(x) + 0x60)
+#define GPIO_INT_CLR(x)		(GPIO_REG(x) + 0x70)
+
+#define GPIO_MSK_CNF(x)		(GPIO_REG(x) + 0x800)
+#define GPIO_MSK_OE(x)		(GPIO_REG(x) + 0x810)
+#define GPIO_MSK_OUT(x)		(GPIO_REG(x) + 0X820)
+#define GPIO_MSK_INT_STA(x)	(GPIO_REG(x) + 0x840)
+#define GPIO_MSK_INT_ENB(x)	(GPIO_REG(x) + 0x850)
+#define GPIO_MSK_INT_LVL(x)	(GPIO_REG(x) + 0x860)
+
+#define GPIO_INT_LVL_MASK		0x010101
+#define GPIO_INT_LVL_EDGE_RISING	0x000101
+#define GPIO_INT_LVL_EDGE_FALLING	0x000100
+#define GPIO_INT_LVL_EDGE_BOTH		0x010100
+#define GPIO_INT_LVL_LEVEL_HIGH		0x000001
+#define GPIO_INT_LVL_LEVEL_LOW		0x000000
+
+struct tegra_gpio_bank {
+	int bank;
+	int irq;
+	spinlock_t lvl_lock[4];
+#ifdef CONFIG_PM
+	u32 cnf[4];
+	u32 out[4];
+	u32 oe[4];
+	u32 int_enb[4];
+	u32 int_lvl[4];
+#endif
+};
+
+
+static struct tegra_gpio_bank tegra_gpio_banks[] = {
+	{.bank = 0, .irq = INT_GPIO1},
+	{.bank = 1, .irq = INT_GPIO2},
+	{.bank = 2, .irq = INT_GPIO3},
+	{.bank = 3, .irq = INT_GPIO4},
+	{.bank = 4, .irq = INT_GPIO5},
+	{.bank = 5, .irq = INT_GPIO6},
+	{.bank = 6, .irq = INT_GPIO7},
+};
+
+static int tegra_gpio_compose(int bank, int port, int bit)
+{
+	return (bank << 5) | ((port & 0x3) << 3) | (bit & 0x7);
+}
+
+static void tegra_gpio_mask_write(u32 reg, int gpio, int value)
+{
+	u32 val;
+
+	val = 0x100 << GPIO_BIT(gpio);
+	if (value)
+		val |= 1 << GPIO_BIT(gpio);
+	__raw_writel(val, reg);
+}
+
+void tegra_gpio_enable(int gpio)
+{
+	tegra_gpio_mask_write(GPIO_MSK_CNF(gpio), gpio, 1);
+}
+
+void tegra_gpio_disable(int gpio)
+{
+	tegra_gpio_mask_write(GPIO_MSK_CNF(gpio), gpio, 0);
+}
+
+static void tegra_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	tegra_gpio_mask_write(GPIO_MSK_OUT(offset), offset, value);
+}
+
+static int tegra_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+	return (__raw_readl(GPIO_IN(offset)) >> GPIO_BIT(offset)) & 0x1;
+}
+
+static int tegra_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	tegra_gpio_mask_write(GPIO_MSK_OE(offset), offset, 0);
+	return 0;
+}
+
+static int tegra_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+					int value)
+{
+	tegra_gpio_set(chip, offset, value);
+	tegra_gpio_mask_write(GPIO_MSK_OE(offset), offset, 1);
+	return 0;
+}
+
+
+
+static struct gpio_chip tegra_gpio_chip = {
+	.label			= "tegra-gpio",
+	.direction_input	= tegra_gpio_direction_input,
+	.get			= tegra_gpio_get,
+	.direction_output	= tegra_gpio_direction_output,
+	.set			= tegra_gpio_set,
+	.base			= 0,
+	.ngpio			= TEGRA_NR_GPIOS,
+};
+
+static void tegra_gpio_irq_ack(struct irq_data *d)
+{
+	int gpio = d->irq - INT_GPIO_BASE;
+
+	__raw_writel(1 << GPIO_BIT(gpio), GPIO_INT_CLR(gpio));
+}
+
+static void tegra_gpio_irq_mask(struct irq_data *d)
+{
+	int gpio = d->irq - INT_GPIO_BASE;
+
+	tegra_gpio_mask_write(GPIO_MSK_INT_ENB(gpio), gpio, 0);
+}
+
+static void tegra_gpio_irq_unmask(struct irq_data *d)
+{
+	int gpio = d->irq - INT_GPIO_BASE;
+
+	tegra_gpio_mask_write(GPIO_MSK_INT_ENB(gpio), gpio, 1);
+}
+
+static int tegra_gpio_irq_set_type(struct irq_data *d, unsigned int type)
+{
+	int gpio = d->irq - INT_GPIO_BASE;
+	struct tegra_gpio_bank *bank = irq_data_get_irq_chip_data(d);
+	int port = GPIO_PORT(gpio);
+	int lvl_type;
+	int val;
+	unsigned long flags;
+
+	switch (type & IRQ_TYPE_SENSE_MASK) {
+	case IRQ_TYPE_EDGE_RISING:
+		lvl_type = GPIO_INT_LVL_EDGE_RISING;
+		break;
+
+	case IRQ_TYPE_EDGE_FALLING:
+		lvl_type = GPIO_INT_LVL_EDGE_FALLING;
+		break;
+
+	case IRQ_TYPE_EDGE_BOTH:
+		lvl_type = GPIO_INT_LVL_EDGE_BOTH;
+		break;
+
+	case IRQ_TYPE_LEVEL_HIGH:
+		lvl_type = GPIO_INT_LVL_LEVEL_HIGH;
+		break;
+
+	case IRQ_TYPE_LEVEL_LOW:
+		lvl_type = GPIO_INT_LVL_LEVEL_LOW;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	spin_lock_irqsave(&bank->lvl_lock[port], flags);
+
+	val = __raw_readl(GPIO_INT_LVL(gpio));
+	val &= ~(GPIO_INT_LVL_MASK << GPIO_BIT(gpio));
+	val |= lvl_type << GPIO_BIT(gpio);
+	__raw_writel(val, GPIO_INT_LVL(gpio));
+
+	spin_unlock_irqrestore(&bank->lvl_lock[port], flags);
+
+	if (type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH))
+		__irq_set_handler_locked(d->irq, handle_level_irq);
+	else if (type & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING))
+		__irq_set_handler_locked(d->irq, handle_edge_irq);
+
+	return 0;
+}
+
+static void tegra_gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	struct tegra_gpio_bank *bank;
+	int port;
+	int pin;
+	int unmasked = 0;
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+
+	chained_irq_enter(chip, desc);
+
+	bank = irq_get_handler_data(irq);
+
+	for (port = 0; port < 4; port++) {
+		int gpio = tegra_gpio_compose(bank->bank, port, 0);
+		unsigned long sta = __raw_readl(GPIO_INT_STA(gpio)) &
+			__raw_readl(GPIO_INT_ENB(gpio));
+		u32 lvl = __raw_readl(GPIO_INT_LVL(gpio));
+
+		for_each_set_bit(pin, &sta, 8) {
+			__raw_writel(1 << pin, GPIO_INT_CLR(gpio));
+
+			/* if gpio is edge triggered, clear condition
+			 * before executing the hander so that we don't
+			 * miss edges
+			 */
+			if (lvl & (0x100 << pin)) {
+				unmasked = 1;
+				chained_irq_exit(chip, desc);
+			}
+
+			generic_handle_irq(gpio_to_irq(gpio + pin));
+		}
+	}
+
+	if (!unmasked)
+		chained_irq_exit(chip, desc);
+
+}
+
+#ifdef CONFIG_PM
+void tegra_gpio_resume(void)
+{
+	unsigned long flags;
+	int b;
+	int p;
+
+	local_irq_save(flags);
+
+	for (b = 0; b < ARRAY_SIZE(tegra_gpio_banks); b++) {
+		struct tegra_gpio_bank *bank = &tegra_gpio_banks[b];
+
+		for (p = 0; p < ARRAY_SIZE(bank->oe); p++) {
+			unsigned int gpio = (b<<5) | (p<<3);
+			__raw_writel(bank->cnf[p], GPIO_CNF(gpio));
+			__raw_writel(bank->out[p], GPIO_OUT(gpio));
+			__raw_writel(bank->oe[p], GPIO_OE(gpio));
+			__raw_writel(bank->int_lvl[p], GPIO_INT_LVL(gpio));
+			__raw_writel(bank->int_enb[p], GPIO_INT_ENB(gpio));
+		}
+	}
+
+	local_irq_restore(flags);
+}
+
+void tegra_gpio_suspend(void)
+{
+	unsigned long flags;
+	int b;
+	int p;
+
+	local_irq_save(flags);
+	for (b = 0; b < ARRAY_SIZE(tegra_gpio_banks); b++) {
+		struct tegra_gpio_bank *bank = &tegra_gpio_banks[b];
+
+		for (p = 0; p < ARRAY_SIZE(bank->oe); p++) {
+			unsigned int gpio = (b<<5) | (p<<3);
+			bank->cnf[p] = __raw_readl(GPIO_CNF(gpio));
+			bank->out[p] = __raw_readl(GPIO_OUT(gpio));
+			bank->oe[p] = __raw_readl(GPIO_OE(gpio));
+			bank->int_enb[p] = __raw_readl(GPIO_INT_ENB(gpio));
+			bank->int_lvl[p] = __raw_readl(GPIO_INT_LVL(gpio));
+		}
+	}
+	local_irq_restore(flags);
+}
+
+static int tegra_gpio_wake_enable(struct irq_data *d, unsigned int enable)
+{
+	struct tegra_gpio_bank *bank = irq_data_get_irq_chip_data(d);
+	return irq_set_irq_wake(bank->irq, enable);
+}
+#endif
+
+static struct irq_chip tegra_gpio_irq_chip = {
+	.name		= "GPIO",
+	.irq_ack	= tegra_gpio_irq_ack,
+	.irq_mask	= tegra_gpio_irq_mask,
+	.irq_unmask	= tegra_gpio_irq_unmask,
+	.irq_set_type	= tegra_gpio_irq_set_type,
+#ifdef CONFIG_PM
+	.irq_set_wake	= tegra_gpio_wake_enable,
+#endif
+};
+
+
+/* This lock class tells lockdep that GPIO irqs are in a different
+ * category than their parents, so it won't report false recursion.
+ */
+static struct lock_class_key gpio_lock_class;
+
+static int __init tegra_gpio_init(void)
+{
+	struct tegra_gpio_bank *bank;
+	int i;
+	int j;
+
+	for (i = 0; i < 7; i++) {
+		for (j = 0; j < 4; j++) {
+			int gpio = tegra_gpio_compose(i, j, 0);
+			__raw_writel(0x00, GPIO_INT_ENB(gpio));
+		}
+	}
+
+#ifdef CONFIG_OF_GPIO
+	/*
+	 * This isn't ideal, but it gets things hooked up until this
+	 * driver is converted into a platform_device
+	 */
+	tegra_gpio_chip.of_node = of_find_compatible_node(NULL, NULL,
+						"nvidia,tegra20-gpio");
+#endif /* CONFIG_OF_GPIO */
+
+	gpiochip_add(&tegra_gpio_chip);
+
+	for (i = INT_GPIO_BASE; i < (INT_GPIO_BASE + TEGRA_NR_GPIOS); i++) {
+		bank = &tegra_gpio_banks[GPIO_BANK(irq_to_gpio(i))];
+
+		irq_set_lockdep_class(i, &gpio_lock_class);
+		irq_set_chip_data(i, bank);
+		irq_set_chip_and_handler(i, &tegra_gpio_irq_chip,
+					 handle_simple_irq);
+		set_irq_flags(i, IRQF_VALID);
+	}
+
+	for (i = 0; i < ARRAY_SIZE(tegra_gpio_banks); i++) {
+		bank = &tegra_gpio_banks[i];
+
+		irq_set_chained_handler(bank->irq, tegra_gpio_irq_handler);
+		irq_set_handler_data(bank->irq, bank);
+
+		for (j = 0; j < 4; j++)
+			spin_lock_init(&bank->lvl_lock[j]);
+	}
+
+	return 0;
+}
+
+postcore_initcall(tegra_gpio_init);
+
+void __init tegra_gpio_config(struct tegra_gpio_table *table, int num)
+{
+	int i;
+
+	for (i = 0; i < num; i++) {
+		int gpio = table[i].gpio;
+
+		if (table[i].enable)
+			tegra_gpio_enable(gpio);
+		else
+			tegra_gpio_disable(gpio);
+	}
+}
+
+#ifdef	CONFIG_DEBUG_FS
+
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
+
+static int dbg_gpio_show(struct seq_file *s, void *unused)
+{
+	int i;
+	int j;
+
+	for (i = 0; i < 7; i++) {
+		for (j = 0; j < 4; j++) {
+			int gpio = tegra_gpio_compose(i, j, 0);
+			seq_printf(s,
+				"%d:%d %02x %02x %02x %02x %02x %02x %06x\n",
+				i, j,
+				__raw_readl(GPIO_CNF(gpio)),
+				__raw_readl(GPIO_OE(gpio)),
+				__raw_readl(GPIO_OUT(gpio)),
+				__raw_readl(GPIO_IN(gpio)),
+				__raw_readl(GPIO_INT_STA(gpio)),
+				__raw_readl(GPIO_INT_ENB(gpio)),
+				__raw_readl(GPIO_INT_LVL(gpio)));
+		}
+	}
+	return 0;
+}
+
+static int dbg_gpio_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, dbg_gpio_show, &inode->i_private);
+}
+
+static const struct file_operations debug_fops = {
+	.open		= dbg_gpio_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+};
+
+static int __init tegra_gpio_debuginit(void)
+{
+	(void) debugfs_create_file("tegra_gpio", S_IRUGO,
+					NULL, NULL, &debug_fops);
+	return 0;
+}
+late_initcall(tegra_gpio_debuginit);
+#endif
diff --git a/drivers/gpio/timbgpio.c b/drivers/gpio/gpio-timberdale.c
index 0265872e57d..c593bd46bfb 100644
--- a/drivers/gpio/timbgpio.c
+++ b/drivers/gpio/gpio-timberdale.c
@@ -1,5 +1,5 @@
 /*
- * timbgpio.c timberdale FPGA GPIO driver
+ * Timberdale FPGA GPIO driver
  * Copyright (c) 2009 Intel Corporation
  *
  * This program is free software; you can redistribute it and/or modify
diff --git a/drivers/gpio/tps65910-gpio.c b/drivers/gpio/gpio-tps65910.c
index 15097ca616d..b9c1c297669 100644
--- a/drivers/gpio/tps65910-gpio.c
+++ b/drivers/gpio/gpio-tps65910.c
@@ -1,5 +1,5 @@
 /*
- * tps65910-gpio.c  --  TI TPS6591x
+ * TI TPS6591x GPIO driver
  *
  * Copyright 2010 Texas Instruments Inc.
  *
diff --git a/drivers/gpio/twl4030-gpio.c b/drivers/gpio/gpio-twl4030.c
index 57635ac35a7..b8b4f228757 100644
--- a/drivers/gpio/twl4030-gpio.c
+++ b/drivers/gpio/gpio-twl4030.c
@@ -1,5 +1,5 @@
 /*
- * twl4030_gpio.c -- access to GPIOs on TWL4030/TPS659x0 chips
+ * Access to GPIOs on TWL4030/TPS659x0 chips
  *
  * Copyright (C) 2006-2007 Texas Instruments, Inc.
  * Copyright (C) 2006 MontaVista Software, Inc.
diff --git a/drivers/gpio/gpio-u300.c b/drivers/gpio/gpio-u300.c
index d92790140fe..fd2dfeeefdf 100644
--- a/drivers/gpio/gpio-u300.c
+++ b/drivers/gpio/gpio-u300.c
@@ -1,11 +1,8 @@
 /*
- *
- * arch/arm/mach-u300/gpio.c
- *
+ * U300 GPIO module.
  *
  * Copyright (C) 2007-2009 ST-Ericsson AB
  * License terms: GNU General Public License (GPL) version 2
- * U300 GPIO module.
  * This can driver either of the two basic GPIO cores
  * available in the U300 platforms:
  * COH 901 335   - Used in DB3150 (U300 1.0) and DB3200 (U330 1.0)
diff --git a/drivers/gpio/ucb1400_gpio.c b/drivers/gpio/gpio-ucb1400.c
index 50e6bd1392c..50e6bd1392c 100644
--- a/drivers/gpio/ucb1400_gpio.c
+++ b/drivers/gpio/gpio-ucb1400.c
diff --git a/drivers/gpio/vr41xx_giu.c b/drivers/gpio/gpio-vr41xx.c
index a365be040b3..98723cb9ac6 100644
--- a/drivers/gpio/vr41xx_giu.c
+++ b/drivers/gpio/gpio-vr41xx.c
@@ -518,7 +518,7 @@ static int __devinit giu_probe(struct platform_device *pdev)
 	if (!res)
 		return -EBUSY;
 
-	giu_base = ioremap(res->start, res->end - res->start + 1);
+	giu_base = ioremap(res->start, resource_size(res));
 	if (!giu_base)
 		return -ENOMEM;
 
diff --git a/drivers/gpio/vx855_gpio.c b/drivers/gpio/gpio-vx855.c
index ef5aabd8b8b..ef5aabd8b8b 100644
--- a/drivers/gpio/vx855_gpio.c
+++ b/drivers/gpio/gpio-vx855.c
diff --git a/drivers/gpio/wm831x-gpio.c b/drivers/gpio/gpio-wm831x.c
index 2bcfb0be09f..deb949e75ec 100644
--- a/drivers/gpio/wm831x-gpio.c
+++ b/drivers/gpio/gpio-wm831x.c
@@ -1,5 +1,5 @@
 /*
- * wm831x-gpio.c  --  gpiolib support for Wolfson WM831x PMICs
+ * gpiolib support for Wolfson WM831x PMICs
  *
  * Copyright 2009 Wolfson Microelectronics PLC.
  *
diff --git a/drivers/gpio/wm8350-gpiolib.c b/drivers/gpio/gpio-wm8350.c
index 359999290f5..a06af515483 100644
--- a/drivers/gpio/wm8350-gpiolib.c
+++ b/drivers/gpio/gpio-wm8350.c
@@ -1,5 +1,5 @@
 /*
- * wm835x-gpiolib.c  --  gpiolib support for Wolfson WM835x PMICs
+ * gpiolib support for Wolfson WM835x PMICs
  *
  * Copyright 2009 Wolfson Microelectronics PLC.
  *
diff --git a/drivers/gpio/wm8994-gpio.c b/drivers/gpio/gpio-wm8994.c
index c822baacd8f..96198f3fab7 100644
--- a/drivers/gpio/wm8994-gpio.c
+++ b/drivers/gpio/gpio-wm8994.c
@@ -1,5 +1,5 @@
 /*
- * wm8994-gpio.c  --  gpiolib support for Wolfson WM8994
+ * gpiolib support for Wolfson WM8994
  *
  * Copyright 2009 Wolfson Microelectronics PLC.
  *
diff --git a/drivers/gpio/xilinx_gpio.c b/drivers/gpio/gpio-xilinx.c
index 846fbd5e31b..846fbd5e31b 100644
--- a/drivers/gpio/xilinx_gpio.c
+++ b/drivers/gpio/gpio-xilinx.c
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 713d43b4e56..6c21c2986ca 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -92,7 +92,7 @@ config LEDS_NET48XX
 config LEDS_NET5501
 	tristate "LED Support for Soekris net5501 series Error LED"
 	depends on LEDS_TRIGGERS
-	depends on X86 && LEDS_GPIO_PLATFORM && GPIO_CS5535
+	depends on X86 && GPIO_CS5535
 	select LEDS_TRIGGER_DEFAULT_ON
 	default n
 	help
@@ -182,23 +182,6 @@ config LEDS_GPIO
 	  defined as platform devices and/or OpenFirmware platform devices.
 	  The code to use these bindings can be selected below.
 
-config LEDS_GPIO_PLATFORM
-	bool "Platform device bindings for GPIO LEDs"
-	depends on LEDS_GPIO
-	default y
-	help
-	  Let the leds-gpio driver drive LEDs which have been defined as
-	  platform devices.  If you don't know what this means, say yes.
-
-config LEDS_GPIO_OF
-	bool "OpenFirmware platform device bindings for GPIO LEDs"
-	depends on LEDS_GPIO && OF_DEVICE
-	default y
-	help
-	  Let the leds-gpio driver drive LEDs which have been defined as
-	  of_platform devices.  For instance, LEDs which are listed in a "dts"
-	  file.
-
 config LEDS_LP3944
 	tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
 	depends on LEDS_CLASS
diff --git a/drivers/leds/leds-gpio.c b/drivers/leds/leds-gpio.c
index b0480c8fbcb..3d8bc327a68 100644
--- a/drivers/leds/leds-gpio.c
+++ b/drivers/leds/leds-gpio.c
@@ -165,7 +165,7 @@ static inline int sizeof_gpio_leds_priv(int num_leds)
 }
 
 /* Code to create from OpenFirmware platform devices */
-#ifdef CONFIG_LEDS_GPIO_OF
+#ifdef CONFIG_OF_GPIO
 static struct gpio_leds_priv * __devinit gpio_leds_create_of(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node, *child;
@@ -223,13 +223,13 @@ static const struct of_device_id of_gpio_leds_match[] = {
 	{ .compatible = "gpio-leds", },
 	{},
 };
-#else
+#else /* CONFIG_OF_GPIO */
 static struct gpio_leds_priv * __devinit gpio_leds_create_of(struct platform_device *pdev)
 {
 	return NULL;
 }
 #define of_gpio_leds_match NULL
-#endif
+#endif /* CONFIG_OF_GPIO */
 
 
 static int __devinit gpio_led_probe(struct platform_device *pdev)
diff --git a/drivers/of/gpio.c b/drivers/of/gpio.c
index 905960338fb..3007662ac61 100644
--- a/drivers/of/gpio.c
+++ b/drivers/of/gpio.c
@@ -21,8 +21,9 @@
 #include <linux/slab.h>
 
 /**
- * of_get_gpio_flags - Get a GPIO number and flags to use with GPIO API
+ * of_get_named_gpio_flags() - Get a GPIO number and flags to use with GPIO API
  * @np:		device node to get GPIO from
+ * @propname:	property name containing gpio specifier(s)
  * @index:	index of the GPIO
  * @flags:	a flags pointer to fill in
  *
@@ -30,8 +31,8 @@
  * value on the error condition. If @flags is not NULL the function also fills
  * in flags for the GPIO.
  */
-int of_get_gpio_flags(struct device_node *np, int index,
-		      enum of_gpio_flags *flags)
+int of_get_named_gpio_flags(struct device_node *np, const char *propname,
+                           int index, enum of_gpio_flags *flags)
 {
 	int ret;
 	struct device_node *gpio_np;
@@ -40,7 +41,7 @@ int of_get_gpio_flags(struct device_node *np, int index,
 	const void *gpio_spec;
 	const __be32 *gpio_cells;
 
-	ret = of_parse_phandles_with_args(np, "gpios", "#gpio-cells", index,
+	ret = of_parse_phandles_with_args(np, propname, "#gpio-cells", index,
 					  &gpio_np, &gpio_spec);
 	if (ret) {
 		pr_debug("%s: can't parse gpios property\n", __func__);
@@ -79,7 +80,7 @@ err0:
 	pr_debug("%s exited with status %d\n", __func__, ret);
 	return ret;
 }
-EXPORT_SYMBOL(of_get_gpio_flags);
+EXPORT_SYMBOL(of_get_named_gpio_flags);
 
 /**
  * of_gpio_count - Count GPIOs for a device