diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/net/wireless/rtl8187.h | 4 | ||||
| -rw-r--r-- | drivers/net/wireless/rtl8187_dev.c | 15 |
2 files changed, 18 insertions, 1 deletions
diff --git a/drivers/net/wireless/rtl8187.h b/drivers/net/wireless/rtl8187.h index 1b0d750f662..5a9515c9996 100644 --- a/drivers/net/wireless/rtl8187.h +++ b/drivers/net/wireless/rtl8187.h @@ -94,6 +94,10 @@ struct rtl8187_priv { const struct rtl818x_rf_ops *rf; struct ieee80211_vif *vif; int mode; + /* The mutex protects the TX loopback state. + * Any attempt to set channels concurrently locks the device. + */ + struct mutex conf_mutex; /* rtl8187 specific */ struct ieee80211_channel channels[14]; diff --git a/drivers/net/wireless/rtl8187_dev.c b/drivers/net/wireless/rtl8187_dev.c index 461aa26164c..57376fb993e 100644 --- a/drivers/net/wireless/rtl8187_dev.c +++ b/drivers/net/wireless/rtl8187_dev.c @@ -728,6 +728,7 @@ static int rtl8187_start(struct ieee80211_hw *dev) if (ret) return ret; + mutex_lock(&priv->conf_mutex); if (priv->is_rtl8187b) { reg = RTL818X_RX_CONF_MGMT | RTL818X_RX_CONF_DATA | @@ -749,6 +750,7 @@ static int rtl8187_start(struct ieee80211_hw *dev) (7 << 0 /* long retry limit */) | (7 << 21 /* MAX TX DMA */)); rtl8187_init_urbs(dev); + mutex_unlock(&priv->conf_mutex); return 0; } @@ -792,6 +794,7 @@ static int rtl8187_start(struct ieee80211_hw *dev) reg |= RTL818X_CMD_TX_ENABLE; reg |= RTL818X_CMD_RX_ENABLE; rtl818x_iowrite8(priv, &priv->map->CMD, reg); + mutex_unlock(&priv->conf_mutex); return 0; } @@ -803,6 +806,7 @@ static void rtl8187_stop(struct ieee80211_hw *dev) struct sk_buff *skb; u32 reg; + mutex_lock(&priv->conf_mutex); rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0); reg = rtl818x_ioread8(priv, &priv->map->CMD); @@ -822,7 +826,7 @@ static void rtl8187_stop(struct ieee80211_hw *dev) usb_kill_urb(info->urb); kfree_skb(skb); } - return; + mutex_unlock(&priv->conf_mutex); } static int rtl8187_add_interface(struct ieee80211_hw *dev, @@ -842,6 +846,7 @@ static int rtl8187_add_interface(struct ieee80211_hw *dev, return -EOPNOTSUPP; } + mutex_lock(&priv->conf_mutex); priv->vif = conf->vif; rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); @@ -850,6 +855,7 @@ static int rtl8187_add_interface(struct ieee80211_hw *dev, ((u8 *)conf->mac_addr)[i]); rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + mutex_unlock(&priv->conf_mutex); return 0; } @@ -857,8 +863,10 @@ static void rtl8187_remove_interface(struct ieee80211_hw *dev, struct ieee80211_if_init_conf *conf) { struct rtl8187_priv *priv = dev->priv; + mutex_lock(&priv->conf_mutex); priv->mode = IEEE80211_IF_TYPE_MNTR; priv->vif = NULL; + mutex_unlock(&priv->conf_mutex); } static int rtl8187_config(struct ieee80211_hw *dev, struct ieee80211_conf *conf) @@ -866,6 +874,7 @@ static int rtl8187_config(struct ieee80211_hw *dev, struct ieee80211_conf *conf) struct rtl8187_priv *priv = dev->priv; u32 reg; + mutex_lock(&priv->conf_mutex); reg = rtl818x_ioread32(priv, &priv->map->TX_CONF); /* Enable TX loopback on MAC level to avoid TX during channel * changes, as this has be seen to causes problems and the @@ -898,6 +907,7 @@ static int rtl8187_config(struct ieee80211_hw *dev, struct ieee80211_conf *conf) rtl818x_iowrite16(priv, &priv->map->ATIMTR_INTERVAL, 100); rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL, 100); rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL_TIME, 100); + mutex_unlock(&priv->conf_mutex); return 0; } @@ -909,6 +919,7 @@ static int rtl8187_config_interface(struct ieee80211_hw *dev, int i; u8 reg; + mutex_lock(&priv->conf_mutex); for (i = 0; i < ETH_ALEN; i++) rtl818x_iowrite8(priv, &priv->map->BSSID[i], conf->bssid[i]); @@ -922,6 +933,7 @@ static int rtl8187_config_interface(struct ieee80211_hw *dev, rtl818x_iowrite8(priv, &priv->map->MSR, reg); } + mutex_unlock(&priv->conf_mutex); return 0; } @@ -1189,6 +1201,7 @@ static int __devinit rtl8187_probe(struct usb_interface *intf, printk(KERN_ERR "rtl8187: Cannot register device\n"); goto err_free_dev; } + mutex_init(&priv->conf_mutex); printk(KERN_INFO "%s: hwaddr %s, %s V%d + %s\n", wiphy_name(dev->wiphy), print_mac(mac, dev->wiphy->perm_addr), |