diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/gpio/gpiolib.c | 3 | ||||
| -rw-r--r-- | drivers/of/of_mdio.c | 2 | ||||
| -rw-r--r-- | drivers/serial/mpc52xx_uart.c | 33 | ||||
| -rw-r--r-- | drivers/spi/omap2_mcspi.c | 5 | ||||
| -rw-r--r-- | drivers/spi/spi.c | 8 |
5 files changed, 11 insertions, 40 deletions
diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c index 76be229c814..eb0c3fe44b2 100644 --- a/drivers/gpio/gpiolib.c +++ b/drivers/gpio/gpiolib.c @@ -416,7 +416,8 @@ static int gpio_setup_irq(struct gpio_desc *desc, struct device *dev, return 0; free_sd: - sysfs_put(pdesc->value_sd); + if (pdesc) + sysfs_put(pdesc->value_sd); free_id: idr_remove(&pdesc_idr, id); desc->flags &= GPIO_FLAGS_MASK; diff --git a/drivers/of/of_mdio.c b/drivers/of/of_mdio.c index 18ecae4a437..b4748337223 100644 --- a/drivers/of/of_mdio.c +++ b/drivers/of/of_mdio.c @@ -69,7 +69,7 @@ int of_mdiobus_register(struct mii_bus *mdio, struct device_node *np) } phy = get_phy_device(mdio, be32_to_cpup(addr)); - if (!phy) { + if (!phy || IS_ERR(phy)) { dev_err(&mdio->dev, "error probing PHY at address %i\n", *addr); continue; diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c index 3119fddaedb..a176ab4bd65 100644 --- a/drivers/serial/mpc52xx_uart.c +++ b/drivers/serial/mpc52xx_uart.c @@ -29,39 +29,6 @@ * kind, whether express or implied. */ -/* Platform device Usage : - * - * Since PSCs can have multiple function, the correct driver for each one - * is selected by calling mpc52xx_match_psc_function(...). The function - * handled by this driver is "uart". - * - * The driver init all necessary registers to place the PSC in uart mode without - * DCD. However, the pin multiplexing aren't changed and should be set either - * by the bootloader or in the platform init code. - * - * The idx field must be equal to the PSC index (e.g. 0 for PSC1, 1 for PSC2, - * and so on). So the PSC1 is mapped to /dev/ttyPSC0, PSC2 to /dev/ttyPSC1 and - * so on. But be warned, it's an ABSOLUTE REQUIREMENT ! This is needed mainly - * fpr the console code : without this 1:1 mapping, at early boot time, when we - * are parsing the kernel args console=ttyPSC?, we wouldn't know which PSC it - * will be mapped to. - */ - -/* OF Platform device Usage : - * - * This driver is only used for PSCs configured in uart mode. The device - * tree will have a node for each PSC with "mpc52xx-psc-uart" in the compatible - * list. - * - * By default, PSC devices are enumerated in the order they are found. However - * a particular PSC number can be forces by adding 'device_no = <port#>' - * to the device node. - * - * The driver init all necessary registers to place the PSC in uart mode without - * DCD. However, the pin multiplexing aren't changed and should be set either - * by the bootloader or in the platform init code. - */ - #undef DEBUG #include <linux/device.h> diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c index d8356af118a..e0de0d0eede 100644 --- a/drivers/spi/omap2_mcspi.c +++ b/drivers/spi/omap2_mcspi.c @@ -204,6 +204,7 @@ static inline void mcspi_write_chconf0(const struct spi_device *spi, u32 val) cs->chconf0 = val; mcspi_write_cs_reg(spi, OMAP2_MCSPI_CHCONF0, val); + mcspi_read_cs_reg(spi, OMAP2_MCSPI_CHCONF0); } static void omap2_mcspi_set_dma_req(const struct spi_device *spi, @@ -532,7 +533,7 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer) goto out; } #ifdef VERBOSE - dev_dbg(&spi->dev, "write-%d %04x\n", + dev_dbg(&spi->dev, "write-%d %08x\n", word_len, *tx); #endif __raw_writel(*tx++, tx_reg); @@ -550,7 +551,7 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer) mcspi_write_chconf0(spi, l); *rx++ = __raw_readl(rx_reg); #ifdef VERBOSE - dev_dbg(&spi->dev, "read-%d %04x\n", + dev_dbg(&spi->dev, "read-%d %08x\n", word_len, *(rx - 1)); #endif } diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c index 9ffb0fdbd6f..b3a1f9259b6 100644 --- a/drivers/spi/spi.c +++ b/drivers/spi/spi.c @@ -41,7 +41,7 @@ static void spidev_release(struct device *dev) spi->master->cleanup(spi); spi_master_put(spi->master); - kfree(dev); + kfree(spi); } static ssize_t @@ -257,6 +257,7 @@ int spi_add_device(struct spi_device *spi) { static DEFINE_MUTEX(spi_add_lock); struct device *dev = spi->master->dev.parent; + struct device *d; int status; /* Chipselects are numbered 0..max; validate. */ @@ -278,10 +279,11 @@ int spi_add_device(struct spi_device *spi) */ mutex_lock(&spi_add_lock); - if (bus_find_device_by_name(&spi_bus_type, NULL, dev_name(&spi->dev)) - != NULL) { + d = bus_find_device_by_name(&spi_bus_type, NULL, dev_name(&spi->dev)); + if (d != NULL) { dev_err(dev, "chipselect %d already in use\n", spi->chip_select); + put_device(d); status = -EBUSY; goto done; } |