diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/dma/amba-pl08x.c | 141 |
1 files changed, 17 insertions, 124 deletions
diff --git a/drivers/dma/amba-pl08x.c b/drivers/dma/amba-pl08x.c index 6bba32e5ddb..be9a1c718f9 100644 --- a/drivers/dma/amba-pl08x.c +++ b/drivers/dma/amba-pl08x.c @@ -149,14 +149,6 @@ struct pl08x_driver_data { * PL08X specific defines */ -/* - * Memory boundaries: the manual for PL08x says that the controller - * cannot read past a 1KiB boundary, so these defines are used to - * create transfer LLIs that do not cross such boundaries. - */ -#define PL08X_BOUNDARY_SHIFT (10) /* 1KB 0x400 */ -#define PL08X_BOUNDARY_SIZE (1 << PL08X_BOUNDARY_SHIFT) - /* Size (bytes) of each LLI buffer allocated for one transfer */ # define PL08X_LLI_TSFR_SIZE 0x2000 @@ -568,18 +560,6 @@ static void pl08x_fill_lli_for_desc(struct pl08x_lli_build_data *bd, } /* - * Return number of bytes to fill to boundary, or len. - * This calculation works for any value of addr. - */ -static inline size_t pl08x_pre_boundary(u32 addr, size_t len) -{ - size_t boundary_len = PL08X_BOUNDARY_SIZE - - (addr & (PL08X_BOUNDARY_SIZE - 1)); - - return min(boundary_len, len); -} - -/* * This fills in the table of LLIs for the transfer descriptor * Note that we assume we never have to change the burst sizes * Return 0 for error @@ -685,118 +665,30 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x, * width left */ while (bd.remainder > (mbus->buswidth - 1)) { - size_t lli_len, target_len, tsize, odd_bytes; + size_t lli_len, tsize; /* * If enough left try to send max possible, * otherwise try to send the remainder */ - target_len = min(bd.remainder, max_bytes_per_lli); - + lli_len = min(bd.remainder, max_bytes_per_lli); /* - * Set bus lengths for incrementing buses to the - * number of bytes which fill to next memory boundary, - * limiting on the target length calculated above. + * Check against minimum bus alignment: Calculate actual + * transfer size in relation to bus width and get a + * maximum remainder of the smallest bus width - 1 */ - if (cctl & PL080_CONTROL_SRC_INCR) - bd.srcbus.fill_bytes = - pl08x_pre_boundary(bd.srcbus.addr, - target_len); - else - bd.srcbus.fill_bytes = target_len; - - if (cctl & PL080_CONTROL_DST_INCR) - bd.dstbus.fill_bytes = - pl08x_pre_boundary(bd.dstbus.addr, - target_len); - else - bd.dstbus.fill_bytes = target_len; - - /* Find the nearest */ - lli_len = min(bd.srcbus.fill_bytes, - bd.dstbus.fill_bytes); - - BUG_ON(lli_len > bd.remainder); - - if (lli_len <= 0) { - dev_err(&pl08x->adev->dev, - "%s lli_len is %zu, <= 0\n", - __func__, lli_len); - return 0; - } - - if (lli_len == target_len) { - /* - * Can send what we wanted. - * Maintain alignment - */ - lli_len = (lli_len/mbus->buswidth) * - mbus->buswidth; - odd_bytes = 0; - } else { - /* - * So now we know how many bytes to transfer - * to get to the nearest boundary. The next - * LLI will past the boundary. However, we - * may be working to a boundary on the slave - * bus. We need to ensure the master stays - * aligned, and that we are working in - * multiples of the bus widths. - */ - odd_bytes = lli_len % mbus->buswidth; - lli_len -= odd_bytes; - - } - - if (lli_len) { - /* - * Check against minimum bus alignment: - * Calculate actual transfer size in relation - * to bus width an get a maximum remainder of - * the smallest bus width - 1 - */ - /* FIXME: use round_down()? */ - tsize = lli_len / min(mbus->buswidth, - sbus->buswidth); - lli_len = tsize * min(mbus->buswidth, - sbus->buswidth); - - if (target_len != lli_len) { - dev_vdbg(&pl08x->adev->dev, - "%s can't send what we want. Desired 0x%08zx, lli of 0x%08zx bytes in txd of 0x%08zx\n", - __func__, target_len, lli_len, txd->len); - } - - cctl = pl08x_cctl_bits(cctl, - bd.srcbus.buswidth, - bd.dstbus.buswidth, - tsize); - - dev_vdbg(&pl08x->adev->dev, - "%s fill lli with single lli chunk of size 0x%08zx (remainder 0x%08zx)\n", - __func__, lli_len, bd.remainder); - pl08x_fill_lli_for_desc(&bd, num_llis++, - lli_len, cctl); - total_bytes += lli_len; - } + tsize = lli_len / min(mbus->buswidth, sbus->buswidth); + lli_len = tsize * min(mbus->buswidth, sbus->buswidth); - if (odd_bytes) { - /* - * Creep past the boundary, maintaining - * master alignment - */ - int j; - for (j = 0; (j < mbus->buswidth) - && (bd.remainder); j++) { - cctl = pl08x_cctl_bits(cctl, 1, 1, 1); - dev_vdbg(&pl08x->adev->dev, - "%s align with boundary, single byte (remain 0x%08zx)\n", - __func__, bd.remainder); - pl08x_fill_lli_for_desc(&bd, - num_llis++, 1, cctl); - total_bytes++; - } - } + dev_vdbg(&pl08x->adev->dev, + "%s fill lli with single lli chunk of " + "size 0x%08zx (remainder 0x%08zx)\n", + __func__, lli_len, bd.remainder); + + cctl = pl08x_cctl_bits(cctl, bd.srcbus.buswidth, + bd.dstbus.buswidth, tsize); + pl08x_fill_lli_for_desc(&bd, num_llis++, lli_len, cctl); + total_bytes += lli_len; } /* @@ -811,6 +703,7 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x, total_bytes++; } } + if (total_bytes != txd->len) { dev_err(&pl08x->adev->dev, "%s size of encoded lli:s don't match total txd, transferred 0x%08zx from size 0x%08zx\n", |