diff options
Diffstat (limited to 'include/asm-arm/arch-aaec2000/aaec2000.h')
| -rw-r--r-- | include/asm-arm/arch-aaec2000/aaec2000.h | 151 |
1 files changed, 151 insertions, 0 deletions
diff --git a/include/asm-arm/arch-aaec2000/aaec2000.h b/include/asm-arm/arch-aaec2000/aaec2000.h new file mode 100644 index 00000000000..0e9b7e18af0 --- /dev/null +++ b/include/asm-arm/arch-aaec2000/aaec2000.h @@ -0,0 +1,151 @@ +/* + * linux/include/asm-arm/arch-aaec2000/aaec2000.h + * + * AAEC-2000 registers definition + * + * Copyright (c) 2005 Nicolas Bellido Y Ortega + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ASM_ARCH_AAEC2000_H +#define __ASM_ARCH_AAEC2000_H + +#ifndef __ASM_ARCH_HARDWARE_H +#error You must include hardware.h not this file +#endif /* __ASM_ARCH_HARDWARE_H */ + +/* Interrupt controller */ +#define IRQ_BASE __REG(0x80000500) +#define IRQ_INTSR __REG(0x80000500) /* Int Status Register */ +#define IRQ_INTRSR __REG(0x80000504) /* Int Raw (unmasked) Status */ +#define IRQ_INTENS __REG(0x80000508) /* Int Enable Set */ +#define IRQ_INTENC __REG(0x8000050c) /* Int Enable Clear */ + +/* UART 1 */ +#define UART1_BASE __REG(0x80000600) +#define UART1_DR __REG(0x80000600) /* Data/FIFO Register */ +#define UART1_LCR __REG(0x80000604) /* Link Control Register */ +#define UART1_BRCR __REG(0x80000608) /* Baud Rate Control Register */ +#define UART1_CR __REG(0x8000060c) /* Control Register */ +#define UART1_SR __REG(0x80000610) /* Status Register */ +#define UART1_INT __REG(0x80000614) /* Interrupt Status Register */ +#define UART1_INTM __REG(0x80000618) /* Interrupt Mask Register */ +#define UART1_INTRES __REG(0x8000061c) /* Int Result (masked status) Register */ + +/* UART 2 */ +#define UART2_BASE __REG(0x80000700) +#define UART2_DR __REG(0x80000700) /* Data/FIFO Register */ +#define UART2_LCR __REG(0x80000704) /* Link Control Register */ +#define UART2_BRCR __REG(0x80000708) /* Baud Rate Control Register */ +#define UART2_CR __REG(0x8000070c) /* Control Register */ +#define UART2_SR __REG(0x80000710) /* Status Register */ +#define UART2_INT __REG(0x80000714) /* Interrupt Status Register */ +#define UART2_INTM __REG(0x80000718) /* Interrupt Mask Register */ +#define UART2_INTRES __REG(0x8000071c) /* Int Result (masked status) Register */ + +/* UART 3 */ +#define UART3_BASE __REG(0x80000800) +#define UART3_DR __REG(0x80000800) /* Data/FIFO Register */ +#define UART3_LCR __REG(0x80000804) /* Link Control Register */ +#define UART3_BRCR __REG(0x80000808) /* Baud Rate Control Register */ +#define UART3_CR __REG(0x8000080c) /* Control Register */ +#define UART3_SR __REG(0x80000810) /* Status Register */ +#define UART3_INT __REG(0x80000814) /* Interrupt Status Register */ +#define UART3_INTM __REG(0x80000818) /* Interrupt Mask Register */ +#define UART3_INTRES __REG(0x8000081c) /* Int Result (masked status) Register */ + +/* These are used in some places */ +#define _UART1_BASE __PREG(UART1_BASE) +#define _UART2_BASE __PREG(UART2_BASE) +#define _UART3_BASE __PREG(UART3_BASE) + +/* UART Registers Offsets */ +#define UART_DR 0x00 +#define UART_LCR 0x04 +#define UART_BRCR 0x08 +#define UART_CR 0x0c +#define UART_SR 0x10 +#define UART_INT 0x14 +#define UART_INTM 0x18 +#define UART_INTRES 0x1c + +/* UART_LCR Bitmask */ +#define UART_LCR_BRK (1 << 0) /* Send Break */ +#define UART_LCR_PEN (1 << 1) /* Parity Enable */ +#define UART_LCR_EP (1 << 2) /* Even/Odd Parity */ +#define UART_LCR_S2 (1 << 3) /* One/Two Stop bits */ +#define UART_LCR_FIFO (1 << 4) /* FIFO Enable */ +#define UART_LCR_WL5 (0 << 5) /* Word Length - 5 bits */ +#define UART_LCR_WL6 (1 << 5) /* Word Length - 6 bits */ +#define UART_LCR_WL7 (1 << 6) /* Word Length - 7 bits */ +#define UART_LCR_WL8 (1 << 7) /* Word Length - 8 bits */ + +/* UART_CR Bitmask */ +#define UART_CR_EN (1 << 0) /* UART Enable */ +#define UART_CR_SIR (1 << 1) /* IrDA SIR Enable */ +#define UART_CR_SIRLP (1 << 2) /* Low Power IrDA Enable */ +#define UART_CR_RXP (1 << 3) /* Receive Pin Polarity */ +#define UART_CR_TXP (1 << 4) /* Transmit Pin Polarity */ +#define UART_CR_MXP (1 << 5) /* Modem Pin Polarity */ +#define UART_CR_LOOP (1 << 6) /* Loopback Mode */ + +/* UART_SR Bitmask */ +#define UART_SR_CTS (1 << 0) /* Clear To Send Status */ +#define UART_SR_DSR (1 << 1) /* Data Set Ready Status */ +#define UART_SR_DCD (1 << 2) /* Data Carrier Detect Status */ +#define UART_SR_TxBSY (1 << 3) /* Transmitter Busy Status */ +#define UART_SR_RxFE (1 << 4) /* Receive FIFO Empty Status */ +#define UART_SR_TxFF (1 << 5) /* Transmit FIFO Full Status */ +#define UART_SR_RxFF (1 << 6) /* Receive FIFO Full Status */ +#define UART_SR_TxFE (1 << 7) /* Transmit FIFO Empty Status */ + +/* UART_INT Bitmask */ +#define UART_INT_RIS (1 << 0) /* Rx Interrupt */ +#define UART_INT_TIS (1 << 1) /* Tx Interrupt */ +#define UART_INT_MIS (1 << 2) /* Modem Interrupt */ +#define UART_INT_RTIS (1 << 3) /* Receive Timeout Interrupt */ + +/* Timer 1 */ +#define TIMER1_BASE __REG(0x80000c00) +#define TIMER1_LOAD __REG(0x80000c00) /* Timer 1 Load Register */ +#define TIMER1_VAL __REG(0x80000c04) /* Timer 1 Value Register */ +#define TIMER1_CTRL __REG(0x80000c08) /* Timer 1 Control Register */ +#define TIMER1_CLEAR __REG(0x80000c0c) /* Timer 1 Clear Register */ + +/* Timer 2 */ +#define TIMER2_BASE __REG(0x80000d00) +#define TIMER2_LOAD __REG(0x80000d00) /* Timer 2 Load Register */ +#define TIMER2_VAL __REG(0x80000d04) /* Timer 2 Value Register */ +#define TIMER2_CTRL __REG(0x80000d08) /* Timer 2 Control Register */ +#define TIMER2_CLEAR __REG(0x80000d0c) /* Timer 2 Clear Register */ + +/* Timer 3 */ +#define TIMER3_BASE __REG(0x80000e00) +#define TIMER3_LOAD __REG(0x80000e00) /* Timer 3 Load Register */ +#define TIMER3_VAL __REG(0x80000e04) /* Timer 3 Value Register */ +#define TIMER3_CTRL __REG(0x80000e08) /* Timer 3 Control Register */ +#define TIMER3_CLEAR __REG(0x80000e0c) /* Timer 3 Clear Register */ + +/* Timer Control register bits */ +#define TIMER_CTRL_ENABLE (1 << 7) /* Enable (Start° Timer */ +#define TIMER_CTRL_PERIODIC (1 << 6) /* Periodic Running Mode */ +#define TIMER_CTRL_FREE_RUNNING (0 << 6) /* Normal Running Mode */ +#define TIMER_CTRL_CLKSEL_508K (1 << 3) /* 508KHz Clock select (Timer 1, 2) */ +#define TIMER_CTRL_CLKSEL_2K (0 << 3) /* 2KHz Clock Select (Timer 1, 2)*/ + +/* Power and State Control */ +#define POWER_BASE __REG(0x80000400) +#define POWER_PWRSR __REG(0x80000400) /* Power Status Register */ +#define POWER_PWRCNT __REG(0x80000404) /* Power/Clock control */ +#define POWER_HALT __REG(0x80000408) /* Power Idle Mode */ +#define POWER_STDBY __REG(0x8000040c) /* Power Standby Mode */ +#define POWER_BLEOI __REG(0x80000410) /* Battery Low End of Interrupt */ +#define POWER_MCEOI __REG(0x80000414) /* Media Changed EoI */ +#define POWER_TEOI __REG(0x80000418) /* Tick EoI */ +#define POWER_STFCLR __REG(0x8000041c) /* NbFlg, RSTFlg, PFFlg, CLDFlg Clear */ +#define POWER_CLKSET __REG(0x80000420) /* Clock Speed Control */ + +#endif /* __ARM_ARCH_AAEC2000_H */ |