diff options
Diffstat (limited to 'include/asm-arm/arch-pxa/pxa-regs.h')
| -rw-r--r-- | include/asm-arm/arch-pxa/pxa-regs.h | 29 |
1 files changed, 29 insertions, 0 deletions
diff --git a/include/asm-arm/arch-pxa/pxa-regs.h b/include/asm-arm/arch-pxa/pxa-regs.h index 51f0fe0ac16..939d9e5020a 100644 --- a/include/asm-arm/arch-pxa/pxa-regs.h +++ b/include/asm-arm/arch-pxa/pxa-regs.h @@ -818,6 +818,23 @@ #define UDCOTGICR_IEIDF (1 << 0) /* OTG ID Change Falling Edge Interrupt Enable */ +#define UP2OCR __REG(0x40600020) /* USB Port 2 Output Control register */ + +#define UP2OCR_CPVEN (1 << 0) /* Charge Pump Vbus Enable */ +#define UP2OCR_CPVPE (1 << 1) /* Charge Pump Vbus Pulse Enable */ +#define UP2OCR_DPPDE (1 << 2) /* Host Port 2 Transceiver D+ Pull Down Enable */ +#define UP2OCR_DMPDE (1 << 3) /* Host Port 2 Transceiver D- Pull Down Enable */ +#define UP2OCR_DPPUE (1 << 4) /* Host Port 2 Transceiver D+ Pull Up Enable */ +#define UP2OCR_DMPUE (1 << 5) /* Host Port 2 Transceiver D- Pull Up Enable */ +#define UP2OCR_DPPUBE (1 << 6) /* Host Port 2 Transceiver D+ Pull Up Bypass Enable */ +#define UP2OCR_DMPUBE (1 << 7) /* Host Port 2 Transceiver D- Pull Up Bypass Enable */ +#define UP2OCR_EXSP (1 << 8) /* External Transceiver Speed Control */ +#define UP2OCR_EXSUS (1 << 9) /* External Transceiver Speed Enable */ +#define UP2OCR_IDON (1 << 10) /* OTG ID Read Enable */ +#define UP2OCR_HXS (1 << 16) /* Host Port 2 Transceiver Output Select */ +#define UP2OCR_HXOE (1 << 17) /* Host Port 2 Transceiver Output Enable */ +#define UP2OCR_SEOS (1 << 24) /* Single-Ended Output Select */ + #define UDCCSN(x) __REG2(0x40600100, (x) << 2) #define UDCCSR0 __REG(0x40600100) /* UDC Control/Status register - Endpoint 0 */ #define UDCCSR0_SA (1 << 7) /* Setup Active */ @@ -1423,6 +1440,7 @@ #define GPIO84_NSSP_RX (84 | GPIO_ALT_FN_2_IN) #define GPIO85_nPCE_1_MD (85 | GPIO_ALT_FN_1_OUT) #define GPIO92_MMCDAT0_MD (92 | GPIO_ALT_FN_1_OUT) +#define GPIO104_pSKTSEL_MD (104 | GPIO_ALT_FN_1_OUT) #define GPIO109_MMCDAT1_MD (109 | GPIO_ALT_FN_1_OUT) #define GPIO110_MMCDAT2_MD (110 | GPIO_ALT_FN_1_OUT) #define GPIO110_MMCCS0_MD (110 | GPIO_ALT_FN_1_OUT) @@ -1510,6 +1528,8 @@ #define PSSR_BFS (1 << 1) /* Battery Fault Status */ #define PSSR_SSS (1 << 0) /* Software Sleep Status */ +#define PSLR_SL_ROD (1 << 20) /* Sleep-Mode/Depp-Sleep Mode nRESET_OUT Disable */ + #define PCFR_RO (1 << 15) /* RDH Override */ #define PCFR_PO (1 << 14) /* PH Override */ #define PCFR_GPROD (1 << 12) /* GPIO nRESET_OUT Disable */ @@ -1517,6 +1537,7 @@ #define PCFR_FVC (1 << 10) /* Frequency/Voltage Change */ #define PCFR_DC_EN (1 << 7) /* Sleep/deep-sleep DC-DC Converter Enable */ #define PCFR_PI2CEN (1 << 6) /* Enable PI2C controller */ +#define PCFR_GPR_EN (1 << 4) /* nRESET_GPIO Pin Enable */ #define PCFR_DS (1 << 3) /* Deep Sleep Mode */ #define PCFR_FS (1 << 2) /* Float Static Chip Selects */ #define PCFR_FP (1 << 1) /* Float PCMCIA controls */ @@ -1810,6 +1831,11 @@ #define LCCR0_PDD_S 12 #define LCCR0_BM (1 << 20) /* Branch mask */ #define LCCR0_OUM (1 << 21) /* Output FIFO underrun mask */ +#define LCCR0_LCDT (1 << 22) /* LCD panel type */ +#define LCCR0_RDSTM (1 << 23) /* Read status interrupt mask */ +#define LCCR0_CMDIM (1 << 24) /* Command interrupt mask */ +#define LCCR0_OUC (1 << 25) /* Overlay Underlay control bit */ +#define LCCR0_LDDALT (1 << 26) /* LDD alternate mapping control */ #define LCCR1_PPL Fld (10, 0) /* Pixels Per Line - 1 */ #define LCCR1_DisWdth(Pixel) /* Display Width [1..800 pix.] */ \ @@ -2062,7 +2088,10 @@ #define UHCFMN __REG(0x4C00003C) /* UHC Frame Number */ #define UHCPERS __REG(0x4C000040) /* UHC Periodic Start */ #define UHCLS __REG(0x4C000044) /* UHC Low Speed Threshold */ + #define UHCRHDA __REG(0x4C000048) /* UHC Root Hub Descriptor A */ +#define UHCRHDA_NOCP (1 << 12) /* No over current protection */ + #define UHCRHDB __REG(0x4C00004C) /* UHC Root Hub Descriptor B */ #define UHCRHS __REG(0x4C000050) /* UHC Root Hub Status */ #define UHCRHPS1 __REG(0x4C000054) /* UHC Root Hub Port 1 Status */ |