diff options
Diffstat (limited to 'include/asm-blackfin')
-rw-r--r-- | include/asm-blackfin/bfin-global.h | 7 | ||||
-rw-r--r-- | include/asm-blackfin/mach-bf527/anomaly.h | 5 | ||||
-rw-r--r-- | include/asm-blackfin/mach-bf527/bfin_serial_5xx.h | 8 | ||||
-rw-r--r-- | include/asm-blackfin/mach-bf533/anomaly.h | 31 | ||||
-rw-r--r-- | include/asm-blackfin/mach-bf533/bfin_serial_5xx.h | 8 | ||||
-rw-r--r-- | include/asm-blackfin/mach-bf537/anomaly.h | 10 | ||||
-rw-r--r-- | include/asm-blackfin/mach-bf537/bfin_serial_5xx.h | 8 | ||||
-rw-r--r-- | include/asm-blackfin/mach-bf548/anomaly.h | 2 | ||||
-rw-r--r-- | include/asm-blackfin/mach-bf548/bfin_serial_5xx.h | 12 | ||||
-rw-r--r-- | include/asm-blackfin/mach-bf561/anomaly.h | 2 | ||||
-rw-r--r-- | include/asm-blackfin/mach-bf561/bfin_serial_5xx.h | 8 |
11 files changed, 64 insertions, 37 deletions
diff --git a/include/asm-blackfin/bfin-global.h b/include/asm-blackfin/bfin-global.h index a9248d88367..76033831eb3 100644 --- a/include/asm-blackfin/bfin-global.h +++ b/include/asm-blackfin/bfin-global.h @@ -105,13 +105,6 @@ extern int sram_free(const void*); extern void *sram_alloc_with_lsl(size_t, unsigned long); extern int sram_free_with_lsl(const void*); -extern void led_on(int); -extern void led_off(int); -extern void led_toggle(int); -extern void led_disp_num(int); -extern void led_toggle_num(int); -extern void init_leds(void); - extern const char bfin_board_name[]; extern unsigned long wall_jiffies; diff --git a/include/asm-blackfin/mach-bf527/anomaly.h b/include/asm-blackfin/mach-bf527/anomaly.h index 735fa02fafb..4725268a5ad 100644 --- a/include/asm-blackfin/mach-bf527/anomaly.h +++ b/include/asm-blackfin/mach-bf527/anomaly.h @@ -15,12 +15,16 @@ /* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot2 Not Supported */ #define ANOMALY_05000074 (1) +/* DMA_RUN Bit Is Not Valid after a Peripheral Receive Channel DMA Stops */ +#define ANOMALY_05000119 (1) /* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */ #define ANOMALY_05000122 (1) /* Spurious Hardware Error from an Access in the Shadow of a Conditional Branch */ #define ANOMALY_05000245 (1) /* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */ #define ANOMALY_05000265 (1) +/* Errors when SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */ +#define ANOMALY_05000312 (1) /* Incorrect Access of OTP_STATUS During otp_write() Function */ #define ANOMALY_05000328 (1) /* Disallowed Configuration Prevents Subsequent Allowed Configuration on Host DMA Port */ @@ -92,7 +96,6 @@ #define ANOMALY_05000266 (0) #define ANOMALY_05000273 (0) #define ANOMALY_05000311 (0) -#define ANOMALY_05000312 (0) #define ANOMALY_05000323 (0) #define ANOMALY_05000363 (0) diff --git a/include/asm-blackfin/mach-bf527/bfin_serial_5xx.h b/include/asm-blackfin/mach-bf527/bfin_serial_5xx.h index 26e3c8076b4..2526b6ed6fa 100644 --- a/include/asm-blackfin/mach-bf527/bfin_serial_5xx.h +++ b/include/asm-blackfin/mach-bf527/bfin_serial_5xx.h @@ -53,6 +53,12 @@ #define UART_SET_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0) #define UART_CLEAR_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0) +#define UART_GET_CTS(x) gpio_get_value(x->cts_pin) +#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1) +#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0) +#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v) +#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0) + #if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART1_CTSRTS) # define CONFIG_SERIAL_BFIN_CTSRTS @@ -90,7 +96,7 @@ struct bfin_serial_port { struct work_struct tx_dma_workqueue; #endif #ifdef CONFIG_SERIAL_BFIN_CTSRTS - struct work_struct cts_workqueue; + struct timer_list cts_timer; int cts_pin; int rts_pin; #endif diff --git a/include/asm-blackfin/mach-bf533/anomaly.h b/include/asm-blackfin/mach-bf533/anomaly.h index 5a6dcc5fa36..8f7ea112fd3 100644 --- a/include/asm-blackfin/mach-bf533/anomaly.h +++ b/include/asm-blackfin/mach-bf533/anomaly.h @@ -2,7 +2,7 @@ * File: include/asm-blackfin/mach-bf533/anomaly.h * Bugs: Enter bugs at http://blackfin.uclinux.org/ * - * Copyright (C) 2004-2007 Analog Devices Inc. + * Copyright (C) 2004-2008 Analog Devices Inc. * Licensed under the GPL-2 or later. */ @@ -176,6 +176,21 @@ #define ANOMALY_05000315 (1) /* Internal Voltage Regulator Values of 1.05V, 1.10V and 1.15V Not Allowed for LQFP Packages */ #define ANOMALY_05000319 (ANOMALY_BF531 || ANOMALY_BF532) +/* Serial Port (SPORT) Multichannel Transmit Failure when Channel 0 Is Disabled */ +#define ANOMALY_05000357 (1) +/* UART Break Signal Issues */ +#define ANOMALY_05000363 (__SILICON_REVISION__ < 5) +/* PPI Underflow Error Goes Undetected in ITU-R 656 Mode */ +#define ANOMALY_05000366 (1) +/* Possible RETS Register Corruption when Subroutine Is under 5 Cycles in Duration */ +#define ANOMALY_05000371 (1) +/* PPI Does Not Start Properly In Specific Mode */ +#define ANOMALY_05000400 (__SILICON_REVISION__ >= 5) +/* SSYNC Stalls Processor when Executed from Non-Cacheable Memory */ +#define ANOMALY_05000402 (__SILICON_REVISION__ >= 5) +/* Level-Sensitive External GPIO Wakeups May Cause Indefinite Stall */ +#define ANOMALY_05000403 (1) + /* These anomalies have been "phased" out of analog.com anomaly sheets and are * here to show running on older silicon just isn't feasible. @@ -249,20 +264,6 @@ #define ANOMALY_05000192 (__SILICON_REVISION__ < 3) /* Internal Voltage Regulator may not start up */ #define ANOMALY_05000206 (__SILICON_REVISION__ < 3) -/* Serial Port (SPORT) Multichannel Transmit Failure when Channel 0 Is Disabled */ -#define ANOMALY_05000357 (1) -/* UART Break Signal Issues */ -#define ANOMALY_05000363 (__SILICON_REVISION__ < 5) -/* PPI Underflow Error Goes Undetected in ITU-R 656 Mode */ -#define ANOMALY_05000366 (1) -/* Possible RETS Register Corruption when Subroutine Is under 5 Cycles in Duration */ -#define ANOMALY_05000371 (1) -/* PPI Does Not Start Properly In Specific Mode */ -#define ANOMALY_05000400 (__SILICON_REVISION__ == 5) -/* SSYNC Stalls Processor when Executed from Non-Cacheable Memory */ -#define ANOMALY_05000402 (__SILICON_REVISION__ == 5) -/* Level-Sensitive External GPIO Wakeups May Cause Indefinite Stall */ -#define ANOMALY_05000403 (1) /* Anomalies that don't exist on this proc */ #define ANOMALY_05000266 (0) diff --git a/include/asm-blackfin/mach-bf533/bfin_serial_5xx.h b/include/asm-blackfin/mach-bf533/bfin_serial_5xx.h index d016603b661..ebf592b59aa 100644 --- a/include/asm-blackfin/mach-bf533/bfin_serial_5xx.h +++ b/include/asm-blackfin/mach-bf533/bfin_serial_5xx.h @@ -53,6 +53,12 @@ #define UART_SET_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0) #define UART_CLEAR_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0) +#define UART_GET_CTS(x) gpio_get_value(x->cts_pin) +#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1) +#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0) +#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v) +#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0) + #ifdef CONFIG_BFIN_UART0_CTSRTS # define CONFIG_SERIAL_BFIN_CTSRTS # ifndef CONFIG_UART0_CTS_PIN @@ -82,7 +88,7 @@ struct bfin_serial_port { # endif #endif #ifdef CONFIG_SERIAL_BFIN_CTSRTS - struct work_struct cts_workqueue; + struct timer_list cts_timer; int cts_pin; int rts_pin; #endif diff --git a/include/asm-blackfin/mach-bf537/anomaly.h b/include/asm-blackfin/mach-bf537/anomaly.h index a6b08facb24..8460ab9c324 100644 --- a/include/asm-blackfin/mach-bf537/anomaly.h +++ b/include/asm-blackfin/mach-bf537/anomaly.h @@ -2,7 +2,7 @@ * File: include/asm-blackfin/mach-bf537/anomaly.h * Bugs: Enter bugs at http://blackfin.uclinux.org/ * - * Copyright (C) 2004-2007 Analog Devices Inc. + * Copyright (C) 2004-2008 Analog Devices Inc. * Licensed under the GPL-2 or later. */ @@ -132,8 +132,8 @@ #define ANOMALY_05000322 (1) /* Ethernet MAC MDIO Reads Do Not Meet IEEE Specification */ #define ANOMALY_05000341 (__SILICON_REVISION__ >= 3) -/* New Feature: UART Remains Enabled after UART Boot (Not Available on Older Silicon) */ -#define ANOMALY_05000350 (__SILICON_REVISION__ < 3) +/* New Feature: UART Remains Enabled after UART Boot */ +#define ANOMALY_05000350 (__SILICON_REVISION__ >= 3) /* Regulator Programming Blocked when Hibernate Wakeup Source Remains Active */ #define ANOMALY_05000355 (1) /* Serial Port (SPORT) Multichannel Transmit Failure when Channel 0 Is Disabled */ @@ -145,12 +145,10 @@ /* Possible RETS Register Corruption when Subroutine Is under 5 Cycles in Duration */ #define ANOMALY_05000371 (1) /* SSYNC Stalls Processor when Executed from Non-Cacheable Memory */ -#define ANOMALY_05000402 (__SILICON_REVISION__ >= 3) +#define ANOMALY_05000402 (__SILICON_REVISION__ >= 5) /* Level-Sensitive External GPIO Wakeups May Cause Indefinite Stall */ #define ANOMALY_05000403 (1) - - /* Anomalies that don't exist on this proc */ #define ANOMALY_05000125 (0) #define ANOMALY_05000158 (0) diff --git a/include/asm-blackfin/mach-bf537/bfin_serial_5xx.h b/include/asm-blackfin/mach-bf537/bfin_serial_5xx.h index f79d1a0e912..1bf56ffa22f 100644 --- a/include/asm-blackfin/mach-bf537/bfin_serial_5xx.h +++ b/include/asm-blackfin/mach-bf537/bfin_serial_5xx.h @@ -53,6 +53,12 @@ #define UART_SET_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0) #define UART_CLEAR_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0) +#define UART_GET_CTS(x) gpio_get_value(x->cts_pin) +#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1) +#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0) +#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v) +#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0) + #if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART1_CTSRTS) # define CONFIG_SERIAL_BFIN_CTSRTS @@ -90,7 +96,7 @@ struct bfin_serial_port { struct work_struct tx_dma_workqueue; #endif #ifdef CONFIG_SERIAL_BFIN_CTSRTS - struct work_struct cts_workqueue; + struct timer_list cts_timer; int cts_pin; int rts_pin; #endif diff --git a/include/asm-blackfin/mach-bf548/anomaly.h b/include/asm-blackfin/mach-bf548/anomaly.h index 49d3cebc529..3ad59655881 100644 --- a/include/asm-blackfin/mach-bf548/anomaly.h +++ b/include/asm-blackfin/mach-bf548/anomaly.h @@ -75,6 +75,8 @@ #define ANOMALY_05000365 (1) /* Addressing Conflict between Boot ROM and Asynchronous Memory */ #define ANOMALY_05000369 (1) +/* Possible RETS Register Corruption when Subroutine Is under 5 Cycles in Duration */ +#define ANOMALY_05000371 (1) /* Mobile DDR Operation Not Functional */ #define ANOMALY_05000377 (1) /* Security/Authentication Speedpath Causes Authentication To Fail To Initiate */ diff --git a/include/asm-blackfin/mach-bf548/bfin_serial_5xx.h b/include/asm-blackfin/mach-bf548/bfin_serial_5xx.h index 5eb46a77d91..5e29446a8e0 100644 --- a/include/asm-blackfin/mach-bf548/bfin_serial_5xx.h +++ b/include/asm-blackfin/mach-bf548/bfin_serial_5xx.h @@ -57,6 +57,12 @@ #define UART_SET_DLAB(uart) /* MMRs not muxed on BF54x */ #define UART_CLEAR_DLAB(uart) /* MMRs not muxed on BF54x */ +#define UART_GET_CTS(x) (UART_GET_MSR(x) & CTS) +#define UART_SET_RTS(x) (UART_PUT_MCR(x, UART_GET_MCR(x) | MRTS)) +#define UART_CLEAR_RTS(x) (UART_PUT_MCR(x, UART_GET_MCR(x) & ~MRTS)) +#define UART_ENABLE_INTS(x, v) UART_SET_IER(x, v) +#define UART_DISABLE_INTS(x) UART_CLEAR_IER(x, 0xF) + #if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART1_CTSRTS) # define CONFIG_SERIAL_BFIN_CTSRTS @@ -93,7 +99,7 @@ struct bfin_serial_port { struct work_struct tx_dma_workqueue; #endif #ifdef CONFIG_SERIAL_BFIN_CTSRTS - struct work_struct cts_workqueue; + struct timer_list cts_timer; int cts_pin; int rts_pin; #endif @@ -181,7 +187,7 @@ static void bfin_serial_hw_init(struct bfin_serial_port *uart) #ifdef CONFIG_BFIN_UART1_CTSRTS peripheral_request(P_UART1_RTS, DRIVER_NAME); - peripheral_request(P_UART1_CTS DRIVER_NAME); + peripheral_request(P_UART1_CTS, DRIVER_NAME); #endif #endif @@ -196,7 +202,7 @@ static void bfin_serial_hw_init(struct bfin_serial_port *uart) #ifdef CONFIG_BFIN_UART3_CTSRTS peripheral_request(P_UART3_RTS, DRIVER_NAME); - peripheral_request(P_UART3_CTS DRIVER_NAME); + peripheral_request(P_UART3_CTS, DRIVER_NAME); #endif #endif SSYNC(); diff --git a/include/asm-blackfin/mach-bf561/anomaly.h b/include/asm-blackfin/mach-bf561/anomaly.h index 82157caa96a..5c5d7d7d695 100644 --- a/include/asm-blackfin/mach-bf561/anomaly.h +++ b/include/asm-blackfin/mach-bf561/anomaly.h @@ -2,7 +2,7 @@ * File: include/asm-blackfin/mach-bf561/anomaly.h * Bugs: Enter bugs at http://blackfin.uclinux.org/ * - * Copyright (C) 2004-2007 Analog Devices Inc. + * Copyright (C) 2004-2008 Analog Devices Inc. * Licensed under the GPL-2 or later. */ diff --git a/include/asm-blackfin/mach-bf561/bfin_serial_5xx.h b/include/asm-blackfin/mach-bf561/bfin_serial_5xx.h index 7a962876929..8aa02780e64 100644 --- a/include/asm-blackfin/mach-bf561/bfin_serial_5xx.h +++ b/include/asm-blackfin/mach-bf561/bfin_serial_5xx.h @@ -53,6 +53,12 @@ #define UART_SET_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0) #define UART_CLEAR_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0) +#define UART_GET_CTS(x) gpio_get_value(x->cts_pin) +#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1) +#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0) +#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v) +#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0) + #ifdef CONFIG_BFIN_UART0_CTSRTS # define CONFIG_SERIAL_BFIN_CTSRTS # ifndef CONFIG_UART0_CTS_PIN @@ -82,7 +88,7 @@ struct bfin_serial_port { # endif #endif #ifdef CONFIG_SERIAL_BFIN_CTSRTS - struct work_struct cts_workqueue; + struct timer_list cts_timer; int cts_pin; int rts_pin; #endif |