summaryrefslogtreecommitdiffstats
path: root/include/asm-cris/etraxgpio.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/asm-cris/etraxgpio.h')
-rw-r--r--include/asm-cris/etraxgpio.h179
1 files changed, 0 insertions, 179 deletions
diff --git a/include/asm-cris/etraxgpio.h b/include/asm-cris/etraxgpio.h
deleted file mode 100644
index 38f1c8e1770..00000000000
--- a/include/asm-cris/etraxgpio.h
+++ /dev/null
@@ -1,179 +0,0 @@
-/*
- * The following devices are accessable using this driver using
- * GPIO_MAJOR (120) and a couple of minor numbers.
- *
- * For ETRAX 100LX (CONFIG_ETRAX_ARCH_V10):
- * /dev/gpioa minor 0, 8 bit GPIO, each bit can change direction
- * /dev/gpiob minor 1, 8 bit GPIO, each bit can change direction
- * /dev/leds minor 2, Access to leds depending on kernelconfig
- * /dev/gpiog minor 3
- * g0dir, g8_15dir, g16_23dir, g24 dir configurable in R_GEN_CONFIG
- * g1-g7 and g25-g31 is both input and outputs but on different pins
- * Also note that some bits change pins depending on what interfaces
- * are enabled.
- *
- * For ETRAX FS (CONFIG_ETRAXFS):
- * /dev/gpioa minor 0, 8 bit GPIO, each bit can change direction
- * /dev/gpiob minor 1, 18 bit GPIO, each bit can change direction
- * /dev/gpioc minor 3, 18 bit GPIO, each bit can change direction
- * /dev/gpiod minor 4, 18 bit GPIO, each bit can change direction
- * /dev/gpioe minor 5, 18 bit GPIO, each bit can change direction
- * /dev/leds minor 2, Access to leds depending on kernelconfig
- *
- * For ARTPEC-3 (CONFIG_CRIS_MACH_ARTPEC3):
- * /dev/gpioa minor 0, 8 bit GPIO, each bit can change direction
- * /dev/gpiob minor 1, 18 bit GPIO, each bit can change direction
- * /dev/gpioc minor 3, 18 bit GPIO, each bit can change direction
- * /dev/gpiod minor 4, 18 bit GPIO, each bit can change direction
- * /dev/leds minor 2, Access to leds depending on kernelconfig
- * /dev/pwm0 minor 16, PWM channel 0 on PA30
- * /dev/pwm1 minor 17, PWM channel 1 on PA31
- * /dev/pwm2 minor 18, PWM channel 2 on PB26
- *
- */
-#ifndef _ASM_ETRAXGPIO_H
-#define _ASM_ETRAXGPIO_H
-
-/* etraxgpio _IOC_TYPE, bits 8 to 15 in ioctl cmd */
-#ifdef CONFIG_ETRAX_ARCH_V10
-#define ETRAXGPIO_IOCTYPE 43
-#define GPIO_MINOR_A 0
-#define GPIO_MINOR_B 1
-#define GPIO_MINOR_LEDS 2
-#define GPIO_MINOR_G 3
-#define GPIO_MINOR_LAST 3
-#endif
-
-#ifdef CONFIG_ETRAXFS
-#define ETRAXGPIO_IOCTYPE 43
-#define GPIO_MINOR_A 0
-#define GPIO_MINOR_B 1
-#define GPIO_MINOR_LEDS 2
-#define GPIO_MINOR_C 3
-#define GPIO_MINOR_D 4
-#define GPIO_MINOR_E 5
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-#define GPIO_MINOR_V 6
-#define GPIO_MINOR_LAST 6
-#else
-#define GPIO_MINOR_LAST 5
-#endif
-#endif
-
-#ifdef CONFIG_CRIS_MACH_ARTPEC3
-#define ETRAXGPIO_IOCTYPE 43
-#define GPIO_MINOR_A 0
-#define GPIO_MINOR_B 1
-#define GPIO_MINOR_LEDS 2
-#define GPIO_MINOR_C 3
-#define GPIO_MINOR_D 4
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-#define GPIO_MINOR_V 6
-#define GPIO_MINOR_LAST 6
-#else
-#define GPIO_MINOR_LAST 4
-#endif
-#define GPIO_MINOR_PWM0 16
-#define GPIO_MINOR_PWM1 17
-#define GPIO_MINOR_PWM2 18
-#define GPIO_MINOR_LAST_PWM GPIO_MINOR_PWM2
-#endif
-
-/* supported ioctl _IOC_NR's */
-
-#define IO_READBITS 0x1 /* read and return current port bits (obsolete) */
-#define IO_SETBITS 0x2 /* set the bits marked by 1 in the argument */
-#define IO_CLRBITS 0x3 /* clear the bits marked by 1 in the argument */
-
-/* the alarm is waited for by select() */
-
-#define IO_HIGHALARM 0x4 /* set alarm on high for bits marked by 1 */
-#define IO_LOWALARM 0x5 /* set alarm on low for bits marked by 1 */
-#define IO_CLRALARM 0x6 /* clear alarm for bits marked by 1 */
-
-/* LED ioctl */
-#define IO_LEDACTIVE_SET 0x7 /* set active led
- * 0=off, 1=green, 2=red, 3=yellow */
-
-/* GPIO direction ioctl's */
-#define IO_READDIR 0x8 /* Read direction 0=input 1=output (obsolete) */
-#define IO_SETINPUT 0x9 /* Set direction for bits set, 0=unchanged 1=input,
- returns mask with current inputs (obsolete) */
-#define IO_SETOUTPUT 0xA /* Set direction for bits set, 0=unchanged 1=output,
- returns mask with current outputs (obsolete)*/
-
-/* LED ioctl extended */
-#define IO_LED_SETBIT 0xB
-#define IO_LED_CLRBIT 0xC
-
-/* SHUTDOWN ioctl */
-#define IO_SHUTDOWN 0xD
-#define IO_GET_PWR_BT 0xE
-
-/* Bit toggling in driver settings */
-/* bit set in low byte0 is CLK mask (0x00FF),
- bit set in byte1 is DATA mask (0xFF00)
- msb, data_mask[7:0] , clk_mask[7:0]
- */
-#define IO_CFG_WRITE_MODE 0xF
-#define IO_CFG_WRITE_MODE_VALUE(msb, data_mask, clk_mask) \
- ( (((msb)&1) << 16) | (((data_mask) &0xFF) << 8) | ((clk_mask) & 0xFF) )
-
-/* The following 4 ioctl's take a pointer as argument and handles
- * 32 bit ports (port G) properly.
- * These replaces IO_READBITS,IO_SETINPUT AND IO_SETOUTPUT
- */
-#define IO_READ_INBITS 0x10 /* *arg is result of reading the input pins */
-#define IO_READ_OUTBITS 0x11 /* *arg is result of reading the output shadow */
-#define IO_SETGET_INPUT 0x12 /* bits set in *arg is set to input,
- * *arg updated with current input pins.
- */
-#define IO_SETGET_OUTPUT 0x13 /* bits set in *arg is set to output,
- * *arg updated with current output pins.
- */
-
-/* The following ioctl's are applicable to the PWM channels only */
-
-#define IO_PWM_SET_MODE 0x20
-
-enum io_pwm_mode {
- PWM_OFF = 0, /* disabled, deallocated */
- PWM_STANDARD = 1, /* 390 kHz, duty cycle 0..255/256 */
- PWM_FAST = 2, /* variable freq, w/ 10ns active pulse len */
- PWM_VARFREQ = 3 /* individually configurable high/low periods */
-};
-
-struct io_pwm_set_mode {
- enum io_pwm_mode mode;
-};
-
-/* Only for mode PWM_VARFREQ. Period lo/high set in increments of 10ns
- * from 10ns (value = 0) to 81920ns (value = 8191)
- * (Resulting frequencies range from 50 MHz (10ns + 10ns) down to
- * 6.1 kHz (81920ns + 81920ns) at 50% duty cycle, to 12.2 kHz at min/max duty
- * cycle (81920 + 10ns or 10ns + 81920ns, respectively).)
- */
-#define IO_PWM_SET_PERIOD 0x21
-
-struct io_pwm_set_period {
- unsigned int lo; /* 0..8191 */
- unsigned int hi; /* 0..8191 */
-};
-
-/* Only for modes PWM_STANDARD and PWM_FAST.
- * For PWM_STANDARD, set duty cycle of 390 kHz PWM output signal, from
- * 0 (value = 0) to 255/256 (value = 255).
- * For PWM_FAST, set duty cycle of PWM output signal from
- * 0% (value = 0) to 100% (value = 255). Output signal in this mode
- * is a 10ns pulse surrounded by a high or low level depending on duty
- * cycle (except for 0% and 100% which result in a constant output).
- * Resulting output frequency varies from 50 MHz at 50% duty cycle,
- * down to 390 kHz at min/max duty cycle.
- */
-#define IO_PWM_SET_DUTY 0x22
-
-struct io_pwm_set_duty {
- int duty; /* 0..255 */
-};
-
-#endif