diff options
Diffstat (limited to 'include/asm-m68k/mac_via.h')
| -rw-r--r-- | include/asm-m68k/mac_via.h | 267 |
1 files changed, 0 insertions, 267 deletions
diff --git a/include/asm-m68k/mac_via.h b/include/asm-m68k/mac_via.h deleted file mode 100644 index 39afb438b65..00000000000 --- a/include/asm-m68k/mac_via.h +++ /dev/null @@ -1,267 +0,0 @@ -/* - * 6522 Versatile Interface Adapter (VIA) - * - * There are two of these on the Mac II. Some IRQ's are vectored - * via them as are assorted bits and bobs - eg rtc, adb. The picture - * is a bit incomplete as the Mac documentation doesn't cover this well - */ - -#ifndef _ASM_MAC_VIA_H_ -#define _ASM_MAC_VIA_H_ - -/* - * Base addresses for the VIAs. There are two in every machine, - * although on some machines the second is an RBV or an OSS. - * The OSS is different enough that it's handled separately. - * - * Do not use these values directly; use the via1 and via2 variables - * instead (and don't forget to check rbv_present when using via2!) - */ - -#define VIA1_BASE (0x50F00000) -#define VIA2_BASE (0x50F02000) -#define RBV_BASE (0x50F26000) - -/* - * Not all of these are true post MacII I think. - * CSA: probably the ones CHRP marks as 'unused' change purposes - * when the IWM becomes the SWIM. - * http://www.rs6000.ibm.com/resource/technology/chrpio/via5.mak.html - * ftp://ftp.austin.ibm.com/pub/technology/spec/chrp/inwork/CHRP_IORef_1.0.pdf - * - * also, http://developer.apple.com/technotes/hw/hw_09.html claims the - * following changes for IIfx: - * VIA1A_vSccWrReq not available and that VIA1A_vSync has moved to an IOP. - * Also, "All of the functionality of VIA2 has been moved to other chips". - */ - -#define VIA1A_vSccWrReq 0x80 /* SCC write. (input) - * [CHRP] SCC WREQ: Reflects the state of the - * Wait/Request pins from the SCC. - * [Macintosh Family Hardware] - * as CHRP on SE/30,II,IIx,IIcx,IIci. - * on IIfx, "0 means an active request" - */ -#define VIA1A_vRev8 0x40 /* Revision 8 board ??? - * [CHRP] En WaitReqB: Lets the WaitReq_L - * signal from port B of the SCC appear on - * the PA7 input pin. Output. - * [Macintosh Family] On the SE/30, this - * is the bit to flip screen buffers. - * 0=alternate, 1=main. - * on II,IIx,IIcx,IIci,IIfx this is a bit - * for Rev ID. 0=II,IIx, 1=IIcx,IIci,IIfx - */ -#define VIA1A_vHeadSel 0x20 /* Head select for IWM. - * [CHRP] unused. - * [Macintosh Family] "Floppy disk - * state-control line SEL" on all but IIfx - */ -#define VIA1A_vOverlay 0x10 /* [Macintosh Family] On SE/30,II,IIx,IIcx - * this bit enables the "Overlay" address - * map in the address decoders as it is on - * reset for mapping the ROM over the reset - * vector. 1=use overlay map. - * On the IIci,IIfx it is another bit of the - * CPU ID: 0=normal IIci, 1=IIci with parity - * feature or IIfx. - * [CHRP] En WaitReqA: Lets the WaitReq_L - * signal from port A of the SCC appear - * on the PA7 input pin (CHRP). Output. - * [MkLinux] "Drive Select" - * (with 0x20 being 'disk head select') - */ -#define VIA1A_vSync 0x08 /* [CHRP] Sync Modem: modem clock select: - * 1: select the external serial clock to - * drive the SCC's /RTxCA pin. - * 0: Select the 3.6864MHz clock to drive - * the SCC cell. - * [Macintosh Family] Correct on all but IIfx - */ - -/* Macintosh Family Hardware sez: bits 0-2 of VIA1A are volume control - * on Macs which had the PWM sound hardware. Reserved on newer models. - * On IIci,IIfx, bits 1-2 are the rest of the CPU ID: - * bit 2: 1=IIci, 0=IIfx - * bit 1: 1 on both IIci and IIfx. - * MkLinux sez bit 0 is 'burnin flag' in this case. - * CHRP sez: VIA1A bits 0-2 and 5 are 'unused': if programmed as - * inputs, these bits will read 0. - */ -#define VIA1A_vVolume 0x07 /* Audio volume mask for PWM */ -#define VIA1A_CPUID0 0x02 /* CPU id bit 0 on RBV, others */ -#define VIA1A_CPUID1 0x04 /* CPU id bit 0 on RBV, others */ -#define VIA1A_CPUID2 0x10 /* CPU id bit 0 on RBV, others */ -#define VIA1A_CPUID3 0x40 /* CPU id bit 0 on RBV, others */ - -/* Info on VIA1B is from Macintosh Family Hardware & MkLinux. - * CHRP offers no info. */ -#define VIA1B_vSound 0x80 /* Sound enable (for compatibility with - * PWM hardware) 0=enabled. - * Also, on IIci w/parity, shows parity error - * 0=error, 1=OK. */ -#define VIA1B_vMystery 0x40 /* On IIci, parity enable. 0=enabled,1=disabled - * On SE/30, vertical sync interrupt enable. - * 0=enabled. This vSync interrupt shows up - * as a slot $E interrupt. */ -#define VIA1B_vADBS2 0x20 /* ADB state input bit 1 (unused on IIfx) */ -#define VIA1B_vADBS1 0x10 /* ADB state input bit 0 (unused on IIfx) */ -#define VIA1B_vADBInt 0x08 /* ADB interrupt 0=interrupt (unused on IIfx)*/ -#define VIA1B_vRTCEnb 0x04 /* Enable Real time clock. 0=enabled. */ -#define VIA1B_vRTCClk 0x02 /* Real time clock serial-clock line. */ -#define VIA1B_vRTCData 0x01 /* Real time clock serial-data line. */ - -/* MkLinux defines the following "VIA1 Register B contents where they - * differ from standard VIA1". From the naming scheme, we assume they - * correspond to a VIA work-alike named 'EVR'. */ -#define EVRB_XCVR 0x08 /* XCVR_SESSION* */ -#define EVRB_FULL 0x10 /* VIA_FULL */ -#define EVRB_SYSES 0x20 /* SYS_SESSION */ -#define EVRB_AUXIE 0x00 /* Enable A/UX Interrupt Scheme */ -#define EVRB_AUXID 0x40 /* Disable A/UX Interrupt Scheme */ -#define EVRB_SFTWRIE 0x00 /* Software Interrupt ReQuest */ -#define EVRB_SFTWRID 0x80 /* Software Interrupt ReQuest */ - -/* - * VIA2 A register is the interrupt lines raised off the nubus - * slots. - * The below info is from 'Macintosh Family Hardware.' - * MkLinux calls the 'IIci internal video IRQ' below the 'RBV slot 0 irq.' - * It also notes that the slot $9 IRQ is the 'Ethernet IRQ' and - * defines the 'Video IRQ' as 0x40 for the 'EVR' VIA work-alike. - * Perhaps OSS uses vRAM1 and vRAM2 for ADB. - */ - -#define VIA2A_vRAM1 0x80 /* RAM size bit 1 (IIci: reserved) */ -#define VIA2A_vRAM0 0x40 /* RAM size bit 0 (IIci: internal video IRQ) */ -#define VIA2A_vIRQE 0x20 /* IRQ from slot $E */ -#define VIA2A_vIRQD 0x10 /* IRQ from slot $D */ -#define VIA2A_vIRQC 0x08 /* IRQ from slot $C */ -#define VIA2A_vIRQB 0x04 /* IRQ from slot $B */ -#define VIA2A_vIRQA 0x02 /* IRQ from slot $A */ -#define VIA2A_vIRQ9 0x01 /* IRQ from slot $9 */ - -/* RAM size bits decoded as follows: - * bit1 bit0 size of ICs in bank A - * 0 0 256 kbit - * 0 1 1 Mbit - * 1 0 4 Mbit - * 1 1 16 Mbit - */ - -/* - * Register B has the fun stuff in it - */ - -#define VIA2B_vVBL 0x80 /* VBL output to VIA1 (60.15Hz) driven by - * timer T1. - * on IIci, parity test: 0=test mode. - * [MkLinux] RBV_PARODD: 1=odd,0=even. */ -#define VIA2B_vSndJck 0x40 /* External sound jack status. - * 0=plug is inserted. On SE/30, always 0 */ -#define VIA2B_vTfr0 0x20 /* Transfer mode bit 0 ack from NuBus */ -#define VIA2B_vTfr1 0x10 /* Transfer mode bit 1 ack from NuBus */ -#define VIA2B_vMode32 0x08 /* 24/32bit switch - doubles as cache flush - * on II, AMU/PMMU control. - * if AMU, 0=24bit to 32bit translation - * if PMMU, 1=PMMU is accessing page table. - * on SE/30 tied low. - * on IIx,IIcx,IIfx, unused. - * on IIci/RBV, cache control. 0=flush cache. - */ -#define VIA2B_vPower 0x04 /* Power off, 0=shut off power. - * on SE/30 this signal sent to PDS card. */ -#define VIA2B_vBusLk 0x02 /* Lock NuBus transactions, 0=locked. - * on SE/30 sent to PDS card. */ -#define VIA2B_vCDis 0x01 /* Cache control. On IIci, 1=disable cache card - * on others, 0=disable processor's instruction - * and data caches. */ - -/* Apple sez: http://developer.apple.com/technotes/ov/ov_04.html - * Another example of a valid function that has no ROM support is the use - * of the alternate video page for page-flipping animation. Since there - * is no ROM call to flip pages, it is necessary to go play with the - * right bit in the VIA chip (6522 Versatile Interface Adapter). - * [CSA: don't know which one this is, but it's one of 'em!] - */ - -/* - * 6522 registers - see databook. - * CSA: Assignments for VIA1 confirmed from CHRP spec. - */ - -/* partial address decode. 0xYYXX : XX part for RBV, YY part for VIA */ -/* Note: 15 VIA regs, 8 RBV regs */ - -#define vBufB 0x0000 /* [VIA/RBV] Register B */ -#define vBufAH 0x0200 /* [VIA only] Buffer A, with handshake. DON'T USE! */ -#define vDirB 0x0400 /* [VIA only] Data Direction Register B. */ -#define vDirA 0x0600 /* [VIA only] Data Direction Register A. */ -#define vT1CL 0x0800 /* [VIA only] Timer one counter low. */ -#define vT1CH 0x0a00 /* [VIA only] Timer one counter high. */ -#define vT1LL 0x0c00 /* [VIA only] Timer one latches low. */ -#define vT1LH 0x0e00 /* [VIA only] Timer one latches high. */ -#define vT2CL 0x1000 /* [VIA only] Timer two counter low. */ -#define vT2CH 0x1200 /* [VIA only] Timer two counter high. */ -#define vSR 0x1400 /* [VIA only] Shift register. */ -#define vACR 0x1600 /* [VIA only] Auxilary control register. */ -#define vPCR 0x1800 /* [VIA only] Peripheral control register. */ - /* CHRP sez never ever to *write* this. - * Mac family says never to *change* this. - * In fact we need to initialize it once at start. */ -#define vIFR 0x1a00 /* [VIA/RBV] Interrupt flag register. */ -#define vIER 0x1c00 /* [VIA/RBV] Interrupt enable register. */ -#define vBufA 0x1e00 /* [VIA/RBV] register A (no handshake) */ - -/* The RBV only decodes the bottom eight address lines; the VIA doesn't - * decode the bottom eight -- so vBufB | rBufB will always get you BufB */ -/* CSA: in fact, only bits 0,1, and 4 seem to be decoded. - * BUT note the values for rIER and rIFR, where the top 8 bits *do* seem - * to matter. In fact *all* of the top 8 bits seem to matter; - * setting rIER=0x1813 and rIFR=0x1803 doesn't work, either. - * Perhaps some sort of 'compatibility mode' is built-in? [21-May-1999] - */ - -#define rBufB 0x0000 /* [VIA/RBV] Register B */ -#define rExp 0x0001 /* [RBV only] RBV future expansion (always 0) */ -#define rSIFR 0x0002 /* [RBV only] RBV slot interrupts register. */ -#define rIFR 0x1a03 /* [VIA/RBV] RBV interrupt flag register. */ -#define rMonP 0x0010 /* [RBV only] RBV video monitor type. */ -#define rChpT 0x0011 /* [RBV only] RBV test mode register (reads as 0). */ -#define rSIER 0x0012 /* [RBV only] RBV slot interrupt enables. */ -#define rIER 0x1c13 /* [VIA/RBV] RBV interrupt flag enable register. */ -#define rBufA rSIFR /* the 'slot interrupts register' is BufA on a VIA */ - -/* - * Video monitor parameters, for rMonP: - */ -#define RBV_DEPTH 0x07 /* bits per pixel: 000=1,001=2,010=4,011=8 */ -#define RBV_MONID 0x38 /* monitor type, as below. */ -#define RBV_VIDOFF 0x40 /* 1 turns off onboard video */ -/* Supported monitor types: */ -#define MON_15BW (1<<3) /* 15" BW portrait. */ -#define MON_IIGS (2<<3) /* 12" color (modified IIGS monitor). */ -#define MON_15RGB (5<<3) /* 15" RGB portrait. */ -#define MON_12OR13 (6<<3) /* 12" BW or 13" RGB. */ -#define MON_NONE (7<<3) /* No monitor attached. */ - -/* To clarify IER manipulations */ -#define IER_SET_BIT(b) (0x80 | (1<<(b)) ) -#define IER_CLR_BIT(b) (0x7F & (1<<(b)) ) - -#ifndef __ASSEMBLY__ - -extern volatile __u8 *via1,*via2; -extern int rbv_present,via_alt_mapping; - -static inline int rbv_set_video_bpp(int bpp) -{ - char val = (bpp==1)?0:(bpp==2)?1:(bpp==4)?2:(bpp==8)?3:-1; - if (!rbv_present || val<0) return -1; - via2[rMonP] = (via2[rMonP] & ~RBV_DEPTH) | val; - return 0; -} - -#endif /* __ASSEMBLY__ */ - -#endif /* _ASM_MAC_VIA_H_ */ |