diff options
Diffstat (limited to 'include/asm-powerpc/smu.h')
| -rw-r--r-- | include/asm-powerpc/smu.h | 379 |
1 files changed, 379 insertions, 0 deletions
diff --git a/include/asm-powerpc/smu.h b/include/asm-powerpc/smu.h new file mode 100644 index 00000000000..dee8eefe47b --- /dev/null +++ b/include/asm-powerpc/smu.h @@ -0,0 +1,379 @@ +#ifndef _SMU_H +#define _SMU_H + +/* + * Definitions for talking to the SMU chip in newer G5 PowerMacs + */ + +#include <linux/config.h> +#include <linux/list.h> + +/* + * Known SMU commands + * + * Most of what is below comes from looking at the Open Firmware driver, + * though this is still incomplete and could use better documentation here + * or there... + */ + + +/* + * Partition info commands + * + * I do not know what those are for at this point + */ +#define SMU_CMD_PARTITION_COMMAND 0x3e + + +/* + * Fan control + * + * This is a "mux" for fan control commands, first byte is the + * "sub" command. + */ +#define SMU_CMD_FAN_COMMAND 0x4a + + +/* + * Battery access + * + * Same command number as the PMU, could it be same syntax ? + */ +#define SMU_CMD_BATTERY_COMMAND 0x6f +#define SMU_CMD_GET_BATTERY_INFO 0x00 + +/* + * Real time clock control + * + * This is a "mux", first data byte contains the "sub" command. + * The "RTC" part of the SMU controls the date, time, powerup + * timer, but also a PRAM + * + * Dates are in BCD format on 7 bytes: + * [sec] [min] [hour] [weekday] [month day] [month] [year] + * with month being 1 based and year minus 100 + */ +#define SMU_CMD_RTC_COMMAND 0x8e +#define SMU_CMD_RTC_SET_PWRUP_TIMER 0x00 /* i: 7 bytes date */ +#define SMU_CMD_RTC_GET_PWRUP_TIMER 0x01 /* o: 7 bytes date */ +#define SMU_CMD_RTC_STOP_PWRUP_TIMER 0x02 +#define SMU_CMD_RTC_SET_PRAM_BYTE_ACC 0x20 /* i: 1 byte (address?) */ +#define SMU_CMD_RTC_SET_PRAM_AUTOINC 0x21 /* i: 1 byte (data?) */ +#define SMU_CMD_RTC_SET_PRAM_LO_BYTES 0x22 /* i: 10 bytes */ +#define SMU_CMD_RTC_SET_PRAM_HI_BYTES 0x23 /* i: 10 bytes */ +#define SMU_CMD_RTC_GET_PRAM_BYTE 0x28 /* i: 1 bytes (address?) */ +#define SMU_CMD_RTC_GET_PRAM_LO_BYTES 0x29 /* o: 10 bytes */ +#define SMU_CMD_RTC_GET_PRAM_HI_BYTES 0x2a /* o: 10 bytes */ +#define SMU_CMD_RTC_SET_DATETIME 0x80 /* i: 7 bytes date */ +#define SMU_CMD_RTC_GET_DATETIME 0x81 /* o: 7 bytes date */ + + /* + * i2c commands + * + * To issue an i2c command, first is to send a parameter block to the + * the SMU. This is a command of type 0x9a with 9 bytes of header + * eventually followed by data for a write: + * + * 0: bus number (from device-tree usually, SMU has lots of busses !) + * 1: transfer type/format (see below) + * 2: device address. For combined and combined4 type transfers, this + * is the "write" version of the address (bit 0x01 cleared) + * 3: subaddress length (0..3) + * 4: subaddress byte 0 (or only byte for subaddress length 1) + * 5: subaddress byte 1 + * 6: subaddress byte 2 + * 7: combined address (device address for combined mode data phase) + * 8: data length + * + * The transfer types are the same good old Apple ones it seems, + * that is: + * - 0x00: Simple transfer + * - 0x01: Subaddress transfer (addr write + data tx, no restart) + * - 0x02: Combined transfer (addr write + restart + data tx) + * + * This is then followed by actual data for a write. + * + * At this point, the OF driver seems to have a limitation on transfer + * sizes of 0xd bytes on reads and 0x5 bytes on writes. I do not know + * wether this is just an OF limit due to some temporary buffer size + * or if this is an SMU imposed limit. This driver has the same limitation + * for now as I use a 0x10 bytes temporary buffer as well + * + * Once that is completed, a response is expected from the SMU. This is + * obtained via a command of type 0x9a with a length of 1 byte containing + * 0 as the data byte. OF also fills the rest of the data buffer with 0xff's + * though I can't tell yet if this is actually necessary. Once this command + * is complete, at this point, all I can tell is what OF does. OF tests + * byte 0 of the reply: + * - on read, 0xfe or 0xfc : bus is busy, wait (see below) or nak ? + * - on read, 0x00 or 0x01 : reply is in buffer (after the byte 0) + * - on write, < 0 -> failure (immediate exit) + * - else, OF just exists (without error, weird) + * + * So on read, there is this wait-for-busy thing when getting a 0xfc or + * 0xfe result. OF does a loop of up to 64 retries, waiting 20ms and + * doing the above again until either the retries expire or the result + * is no longer 0xfe or 0xfc + * + * The Darwin I2C driver is less subtle though. On any non-success status + * from the response command, it waits 5ms and tries again up to 20 times, + * it doesn't differenciate between fatal errors or "busy" status. + * + * This driver provides an asynchronous paramblock based i2c command + * interface to be used either directly by low level code or by a higher + * level driver interfacing to the linux i2c layer. The current + * implementation of this relies on working timers & timer interrupts + * though, so be careful of calling context for now. This may be "fixed" + * in the future by adding a polling facility. + */ +#define SMU_CMD_I2C_COMMAND 0x9a + /* transfer types */ +#define SMU_I2C_TRANSFER_SIMPLE 0x00 +#define SMU_I2C_TRANSFER_STDSUB 0x01 +#define SMU_I2C_TRANSFER_COMBINED 0x02 + +/* + * Power supply control + * + * The "sub" command is an ASCII string in the data, the + * data lenght is that of the string. + * + * The VSLEW command can be used to get or set the voltage slewing. + * - lenght 5 (only "VSLEW") : it returns "DONE" and 3 bytes of + * reply at data offset 6, 7 and 8. + * - lenght 8 ("VSLEWxyz") has 3 additional bytes appended, and is + * used to set the voltage slewing point. The SMU replies with "DONE" + * I yet have to figure out their exact meaning of those 3 bytes in + * both cases. + * + */ +#define SMU_CMD_POWER_COMMAND 0xaa +#define SMU_CMD_POWER_RESTART "RESTART" +#define SMU_CMD_POWER_SHUTDOWN "SHUTDOWN" +#define SMU_CMD_POWER_VOLTAGE_SLEW "VSLEW" + +/* Misc commands + * + * This command seem to be a grab bag of various things + */ +#define SMU_CMD_MISC_df_COMMAND 0xdf +#define SMU_CMD_MISC_df_SET_DISPLAY_LIT 0x02 /* i: 1 byte */ +#define SMU_CMD_MISC_df_NMI_OPTION 0x04 + +/* + * Version info commands + * + * I haven't quite tried to figure out how these work + */ +#define SMU_CMD_VERSION_COMMAND 0xea + + +/* + * Misc commands + * + * This command seem to be a grab bag of various things + */ +#define SMU_CMD_MISC_ee_COMMAND 0xee +#define SMU_CMD_MISC_ee_GET_DATABLOCK_REC 0x02 +#define SMU_CMD_MISC_ee_LEDS_CTRL 0x04 /* i: 00 (00,01) [00] */ +#define SMU_CMD_MISC_ee_GET_DATA 0x05 /* i: 00 , o: ?? */ + + + +/* + * - Kernel side interface - + */ + +#ifdef __KERNEL__ + +/* + * Asynchronous SMU commands + * + * Fill up this structure and submit it via smu_queue_command(), + * and get notified by the optional done() callback, or because + * status becomes != 1 + */ + +struct smu_cmd; + +struct smu_cmd +{ + /* public */ + u8 cmd; /* command */ + int data_len; /* data len */ + int reply_len; /* reply len */ + void *data_buf; /* data buffer */ + void *reply_buf; /* reply buffer */ + int status; /* command status */ + void (*done)(struct smu_cmd *cmd, void *misc); + void *misc; + + /* private */ + struct list_head link; +}; + +/* + * Queues an SMU command, all fields have to be initialized + */ +extern int smu_queue_cmd(struct smu_cmd *cmd); + +/* + * Simple command wrapper. This structure embeds a small buffer + * to ease sending simple SMU commands from the stack + */ +struct smu_simple_cmd +{ + struct smu_cmd cmd; + u8 buffer[16]; +}; + +/* + * Queues a simple command. All fields will be initialized by that + * function + */ +extern int smu_queue_simple(struct smu_simple_cmd *scmd, u8 command, + unsigned int data_len, + void (*done)(struct smu_cmd *cmd, void *misc), + void *misc, + ...); + +/* + * Completion helper. Pass it to smu_queue_simple or as 'done' + * member to smu_queue_cmd, it will call complete() on the struct + * completion passed in the "misc" argument + */ +extern void smu_done_complete(struct smu_cmd *cmd, void *misc); + +/* + * Synchronous helpers. Will spin-wait for completion of a command + */ +extern void smu_spinwait_cmd(struct smu_cmd *cmd); + +static inline void smu_spinwait_simple(struct smu_simple_cmd *scmd) +{ + smu_spinwait_cmd(&scmd->cmd); +} + +/* + * Poll routine to call if blocked with irqs off + */ +extern void smu_poll(void); + + +/* + * Init routine, presence check.... + */ +extern int smu_init(void); +extern int smu_present(void); +struct of_device; +extern struct of_device *smu_get_ofdev(void); + + +/* + * Common command wrappers + */ +extern void smu_shutdown(void); +extern void smu_restart(void); +struct rtc_time; +extern int smu_get_rtc_time(struct rtc_time *time, int spinwait); +extern int smu_set_rtc_time(struct rtc_time *time, int spinwait); + +/* + * SMU command buffer absolute address, exported by pmac_setup, + * this is allocated very early during boot. + */ +extern unsigned long smu_cmdbuf_abs; + + +/* + * Kenrel asynchronous i2c interface + */ + +/* SMU i2c header, exactly matches i2c header on wire */ +struct smu_i2c_param +{ + u8 bus; /* SMU bus ID (from device tree) */ + u8 type; /* i2c transfer type */ + u8 devaddr; /* device address (includes direction) */ + u8 sublen; /* subaddress length */ + u8 subaddr[3]; /* subaddress */ + u8 caddr; /* combined address, filled by SMU driver */ + u8 datalen; /* length of transfer */ + u8 data[7]; /* data */ +}; + +#define SMU_I2C_READ_MAX 0x0d +#define SMU_I2C_WRITE_MAX 0x05 + +struct smu_i2c_cmd +{ + /* public */ + struct smu_i2c_param info; + void (*done)(struct smu_i2c_cmd *cmd, void *misc); + void *misc; + int status; /* 1 = pending, 0 = ok, <0 = fail */ + + /* private */ + struct smu_cmd scmd; + int read; + int stage; + int retries; + u8 pdata[0x10]; + struct list_head link; +}; + +/* + * Call this to queue an i2c command to the SMU. You must fill info, + * including info.data for a write, done and misc. + * For now, no polling interface is provided so you have to use completion + * callback. + */ +extern int smu_queue_i2c(struct smu_i2c_cmd *cmd); + + +#endif /* __KERNEL__ */ + +/* + * - Userland interface - + */ + +/* + * A given instance of the device can be configured for 2 different + * things at the moment: + * + * - sending SMU commands (default at open() time) + * - receiving SMU events (not yet implemented) + * + * Commands are written with write() of a command block. They can be + * "driver" commands (for example to switch to event reception mode) + * or real SMU commands. They are made of a header followed by command + * data if any. + * + * For SMU commands (not for driver commands), you can then read() back + * a reply. The reader will be blocked or not depending on how the device + * file is opened. poll() isn't implemented yet. The reply will consist + * of a header as well, followed by the reply data if any. You should + * always provide a buffer large enough for the maximum reply data, I + * recommand one page. + * + * It is illegal to send SMU commands through a file descriptor configured + * for events reception + * + */ +struct smu_user_cmd_hdr +{ + __u32 cmdtype; +#define SMU_CMDTYPE_SMU 0 /* SMU command */ +#define SMU_CMDTYPE_WANTS_EVENTS 1 /* switch fd to events mode */ + + __u8 cmd; /* SMU command byte */ + __u32 data_len; /* Lenght of data following */ +}; + +struct smu_user_reply_hdr +{ + __u32 status; /* Command status */ + __u32 reply_len; /* Lenght of data follwing */ +}; + +#endif /* _SMU_H */ |