diff options
Diffstat (limited to 'include/asm-sh')
| -rw-r--r-- | include/asm-sh/sh7760fb.h | 197 |
1 files changed, 197 insertions, 0 deletions
diff --git a/include/asm-sh/sh7760fb.h b/include/asm-sh/sh7760fb.h new file mode 100644 index 00000000000..8767f61acec --- /dev/null +++ b/include/asm-sh/sh7760fb.h @@ -0,0 +1,197 @@ +/* + * sh7760fb.h -- platform data for SH7760/SH7763 LCDC framebuffer driver. + * + * (c) 2006-2008 MSC Vertriebsges.m.b.H., + * Manuel Lauss <mano@roarinelk.homelinux.net> + * (c) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> + */ + +#ifndef _ASM_SH_SH7760FB_H +#define _ASM_SH_SH7760FB_H + +/* + * some bits of the colormap registers should be written as zero. + * create a mask for that. + */ +#define SH7760FB_PALETTE_MASK 0x00f8fcf8 + +/* The LCDC dma engine always sets bits 27-26 to 1: this is Area3 */ +#define SH7760FB_DMA_MASK 0x0C000000 + +/* palette */ +#define LDPR(x) (((x) << 2)) + +/* framebuffer registers and bits */ +#define LDICKR 0x400 +#define LDMTR 0x402 +/* see sh7760fb.h for LDMTR bits */ +#define LDDFR 0x404 +#define LDDFR_PABD (1 << 8) +#define LDDFR_COLOR_MASK 0x7F +#define LDSMR 0x406 +#define LDSMR_ROT (1 << 13) +#define LDSARU 0x408 +#define LDSARL 0x40c +#define LDLAOR 0x410 +#define LDPALCR 0x412 +#define LDPALCR_PALS (1 << 4) +#define LDPALCR_PALEN (1 << 0) +#define LDHCNR 0x414 +#define LDHSYNR 0x416 +#define LDVDLNR 0x418 +#define LDVTLNR 0x41a +#define LDVSYNR 0x41c +#define LDACLNR 0x41e +#define LDINTR 0x420 +#define LDPMMR 0x424 +#define LDPSPR 0x426 +#define LDCNTR 0x428 +#define LDCNTR_DON (1 << 0) +#define LDCNTR_DON2 (1 << 4) + +#ifdef CONFIG_CPU_SUBTYPE_SH7763 +# define LDLIRNR 0x440 +/* LDINTR bit */ +# define LDINTR_MINTEN (1 << 15) +# define LDINTR_FINTEN (1 << 14) +# define LDINTR_VSINTEN (1 << 13) +# define LDINTR_VEINTEN (1 << 12) +# define LDINTR_MINTS (1 << 11) +# define LDINTR_FINTS (1 << 10) +# define LDINTR_VSINTS (1 << 9) +# define LDINTR_VEINTS (1 << 8) +# define VINT_START (LDINTR_VSINTEN) +# define VINT_CHECK (LDINTR_VSINTS) +#else +/* LDINTR bit */ +# define LDINTR_VINTSEL (1 << 12) +# define LDINTR_VINTE (1 << 8) +# define LDINTR_VINTS (1 << 0) +# define VINT_START (LDINTR_VINTSEL) +# define VINT_CHECK (LDINTR_VINTS) +#endif + +/* HSYNC polarity inversion */ +#define LDMTR_FLMPOL (1 << 15) + +/* VSYNC polarity inversion */ +#define LDMTR_CL1POL (1 << 14) + +/* DISPLAY-ENABLE polarity inversion */ +#define LDMTR_DISPEN_LOWACT (1 << 13) + +/* DISPLAY DATA BUS polarity inversion */ +#define LDMTR_DPOL_LOWACT (1 << 12) + +/* AC modulation signal enable */ +#define LDMTR_MCNT (1 << 10) + +/* Disable output of HSYNC during VSYNC period */ +#define LDMTR_CL1CNT (1 << 9) + +/* Disable output of VSYNC during VSYNC period */ +#define LDMTR_CL2CNT (1 << 8) + +/* Display types supported by the LCDC */ +#define LDMTR_STN_MONO_4 0x00 +#define LDMTR_STN_MONO_8 0x01 +#define LDMTR_STN_COLOR_4 0x08 +#define LDMTR_STN_COLOR_8 0x09 +#define LDMTR_STN_COLOR_12 0x0A +#define LDMTR_STN_COLOR_16 0x0B +#define LDMTR_DSTN_MONO_8 0x11 +#define LDMTR_DSTN_MONO_16 0x13 +#define LDMTR_DSTN_COLOR_8 0x19 +#define LDMTR_DSTN_COLOR_12 0x1A +#define LDMTR_DSTN_COLOR_16 0x1B +#define LDMTR_TFT_COLOR_16 0x2B + +/* framebuffer color layout */ +#define LDDFR_1BPP_MONO 0x00 +#define LDDFR_2BPP_MONO 0x01 +#define LDDFR_4BPP_MONO 0x02 +#define LDDFR_6BPP_MONO 0x04 +#define LDDFR_4BPP 0x0A +#define LDDFR_8BPP 0x0C +#define LDDFR_16BPP_RGB555 0x1D +#define LDDFR_16BPP_RGB565 0x2D + +/* LCDC Pixclock sources */ +#define LCDC_CLKSRC_BUSCLOCK 0 +#define LCDC_CLKSRC_PERIPHERAL 1 +#define LCDC_CLKSRC_EXTERNAL 2 + +#define LDICKR_CLKSRC(x) \ + (((x) & 3) << 12) + +/* LCDC pixclock input divider. Set to 1 at a minimum! */ +#define LDICKR_CLKDIV(x) \ + ((x) & 0x1f) + +struct sh7760fb_platdata { + + /* Set this member to a valid fb_videmode for the display you + * wish to use. The following members must be initialized: + * xres, yres, hsync_len, vsync_len, sync, + * {left,right,upper,lower}_margin. + * The driver uses the above members to calculate register values + * and memory requirements. Other members are ignored but may + * be used by other framebuffer layer components. + */ + struct fb_videomode *def_mode; + + /* LDMTR includes display type and signal polarity. The + * HSYNC/VSYNC polarities are derived from the fb_var_screeninfo + * data above; however the polarities of the following signals + * must be encoded in the ldmtr member: + * Display Enable signal (default high-active) DISPEN_LOWACT + * Display Data signals (default high-active) DPOL_LOWACT + * AC Modulation signal (default off) MCNT + * Hsync-During-Vsync suppression (default off) CL1CNT + * Vsync-during-vsync suppression (default off) CL2CNT + * NOTE: also set a display type! + * (one of LDMTR_{STN,DSTN,TFT}_{MONO,COLOR}_{4,8,12,16}) + */ + u16 ldmtr; + + /* LDDFR controls framebuffer image format (depth, organization) + * Use ONE of the LDDFR_?BPP_* macros! + */ + u16 lddfr; + + /* LDPMMR and LDPSPR control the timing of the power signals + * for the display. Please read the SH7760 Hardware Manual, + * Chapters 30.3.17, 30.3.18 and 30.4.6! + */ + u16 ldpmmr; + u16 ldpspr; + + /* LDACLNR contains the line numbers after which the AC modulation + * signal is to toggle. Set to ZERO for TFTs or displays which + * do not need it. (Chapter 30.3.15 in SH7760 Hardware Manual). + */ + u16 ldaclnr; + + /* LDICKR contains information on pixelclock source and config. + * Please use the LDICKR_CLKSRC() and LDICKR_CLKDIV() macros. + * minimal value for CLKDIV() must be 1!. + */ + u16 ldickr; + + /* set this member to 1 if you wish to use the LCDC's hardware + * rotation function. This is limited to displays <= 320x200 + * pixels resolution! + */ + int rotate; /* set to 1 to rotate 90 CCW */ + + /* set this to 1 to suppress vsync irq use. */ + int novsync; + + /* blanking hook for platform. Set this if your platform can do + * more than the LCDC in terms of blanking (e.g. disable clock + * generator / backlight power supply / etc. + */ + void (*blank) (int); +}; + +#endif /* _ASM_SH_SH7760FB_H */ |