diff options
Diffstat (limited to 'include/asm-sparc/ecc.h')
| -rw-r--r-- | include/asm-sparc/ecc.h | 122 |
1 files changed, 0 insertions, 122 deletions
diff --git a/include/asm-sparc/ecc.h b/include/asm-sparc/ecc.h deleted file mode 100644 index ccb84b66fef..00000000000 --- a/include/asm-sparc/ecc.h +++ /dev/null @@ -1,122 +0,0 @@ -/* - * ecc.h: Definitions and defines for the external cache/memory - * controller on the sun4m. - * - * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu) - */ - -#ifndef _SPARC_ECC_H -#define _SPARC_ECC_H - -/* These registers are accessed through the SRMMU passthrough ASI 0x20 */ -#define ECC_ENABLE 0x00000000 /* ECC enable register */ -#define ECC_FSTATUS 0x00000008 /* ECC fault status register */ -#define ECC_FADDR 0x00000010 /* ECC fault address register */ -#define ECC_DIGNOSTIC 0x00000018 /* ECC diagnostics register */ -#define ECC_MBAENAB 0x00000020 /* MBus arbiter enable register */ -#define ECC_DMESG 0x00001000 /* Diagnostic message passing area */ - -/* ECC MBus Arbiter Enable register: - * - * ---------------------------------------- - * | |SBUS|MOD3|MOD2|MOD1|RSV| - * ---------------------------------------- - * 31 5 4 3 2 1 0 - * - * SBUS: Enable MBus Arbiter on the SBus 0=off 1=on - * MOD3: Enable MBus Arbiter on MBus module 3 0=off 1=on - * MOD2: Enable MBus Arbiter on MBus module 2 0=off 1=on - * MOD1: Enable MBus Arbiter on MBus module 1 0=off 1=on - */ - -#define ECC_MBAE_SBUS 0x00000010 -#define ECC_MBAE_MOD3 0x00000008 -#define ECC_MBAE_MOD2 0x00000004 -#define ECC_MBAE_MOD1 0x00000002 - -/* ECC Fault Control Register layout: - * - * ----------------------------- - * | RESV | ECHECK | EINT | - * ----------------------------- - * 31 2 1 0 - * - * ECHECK: Enable ECC checking. 0=off 1=on - * EINT: Enable Interrupts for correctable errors. 0=off 1=on - */ -#define ECC_FCR_CHECK 0x00000002 -#define ECC_FCR_INTENAB 0x00000001 - -/* ECC Fault Address Register Zero layout: - * - * ----------------------------------------------------- - * | MID | S | RSV | VA | BM |AT| C| SZ |TYP| PADDR | - * ----------------------------------------------------- - * 31-28 27 26-22 21-14 13 12 11 10-8 7-4 3-0 - * - * MID: ModuleID of the faulting processor. ie. who did it? - * S: Supervisor/Privileged access? 0=no 1=yes - * VA: Bits 19-12 of the virtual faulting address, these are the - * superset bits in the virtual cache and can be used for - * a flush operation if necessary. - * BM: Boot mode? 0=no 1=yes This is just like the SRMMU boot - * mode bit. - * AT: Did this fault happen during an atomic instruction? 0=no - * 1=yes. This means either an 'ldstub' or 'swap' instruction - * was in progress (but not finished) when this fault happened. - * This indicated whether the bus was locked when the fault - * occurred. - * C: Did the pte for this access indicate that it was cacheable? - * 0=no 1=yes - * SZ: The size of the transaction. - * TYP: The transaction type. - * PADDR: Bits 35-32 of the physical address for the fault. - */ -#define ECC_FADDR0_MIDMASK 0xf0000000 -#define ECC_FADDR0_S 0x08000000 -#define ECC_FADDR0_VADDR 0x003fc000 -#define ECC_FADDR0_BMODE 0x00002000 -#define ECC_FADDR0_ATOMIC 0x00001000 -#define ECC_FADDR0_CACHE 0x00000800 -#define ECC_FADDR0_SIZE 0x00000700 -#define ECC_FADDR0_TYPE 0x000000f0 -#define ECC_FADDR0_PADDR 0x0000000f - -/* ECC Fault Address Register One layout: - * - * ------------------------------------- - * | Physical Address 31-0 | - * ------------------------------------- - * 31 0 - * - * You get the upper 4 bits of the physical address from the - * PADDR field in ECC Fault Address Zero register. - */ - -/* ECC Fault Status Register layout: - * - * ---------------------------------------------- - * | RESV|C2E|MULT|SYNDROME|DWORD|UNC|TIMEO|BS|C| - * ---------------------------------------------- - * 31-18 17 16 15-8 7-4 3 2 1 0 - * - * C2E: A C2 graphics error occurred. 0=no 1=yes (SS10 only) - * MULT: Multiple errors occurred ;-O 0=no 1=prom_panic(yes) - * SYNDROME: Controller is mentally unstable. - * DWORD: - * UNC: Uncorrectable error. 0=no 1=yes - * TIMEO: Timeout occurred. 0=no 1=yes - * BS: C2 graphics bad slot access. 0=no 1=yes (SS10 only) - * C: Correctable error? 0=no 1=yes - */ - -#define ECC_FSR_C2ERR 0x00020000 -#define ECC_FSR_MULT 0x00010000 -#define ECC_FSR_SYND 0x0000ff00 -#define ECC_FSR_DWORD 0x000000f0 -#define ECC_FSR_UNC 0x00000008 -#define ECC_FSR_TIMEO 0x00000004 -#define ECC_FSR_BADSLOT 0x00000002 -#define ECC_FSR_C 0x00000001 - -#endif /* !(_SPARC_ECC_H) */ |