diff options
Diffstat (limited to 'include/linux/amba')
| -rw-r--r-- | include/linux/amba/bus.h | 1 | ||||
| -rw-r--r-- | include/linux/amba/mmci.h | 42 | ||||
| -rw-r--r-- | include/linux/amba/xilinx_dma.h | 47 |
3 files changed, 48 insertions, 42 deletions
diff --git a/include/linux/amba/bus.h b/include/linux/amba/bus.h index 63b5eff0a80..fdd7e1b61f6 100644 --- a/include/linux/amba/bus.h +++ b/include/linux/amba/bus.h @@ -47,6 +47,7 @@ struct amba_driver { enum amba_vendor { AMBA_VENDOR_ARM = 0x41, AMBA_VENDOR_ST = 0x80, + AMBA_VENDOR_QCOM = 0x51, }; extern struct bus_type amba_bustype; diff --git a/include/linux/amba/mmci.h b/include/linux/amba/mmci.h index 32a89cf5ec4..8c98113069c 100644 --- a/include/linux/amba/mmci.h +++ b/include/linux/amba/mmci.h @@ -6,28 +6,9 @@ #include <linux/mmc/host.h> - -/* - * These defines is places here due to access is needed from machine - * configuration files. The ST Micro version does not have ROD and - * reuse the voltage registers for direction settings. - */ -#define MCI_ST_DATA2DIREN (1 << 2) -#define MCI_ST_CMDDIREN (1 << 3) -#define MCI_ST_DATA0DIREN (1 << 4) -#define MCI_ST_DATA31DIREN (1 << 5) -#define MCI_ST_FBCLKEN (1 << 7) -#define MCI_ST_DATA74DIREN (1 << 8) - -/* Just some dummy forwarding */ -struct dma_chan; - /** * struct mmci_platform_data - platform configuration for the MMCI * (also known as PL180) block. - * @f_max: the maximum operational frequency for this host in this - * platform configuration. When this is specified it takes precedence - * over the module parameter for the same frequency. * @ocr_mask: available voltages on the 4 pins from the block, this * is ignored if a regulator is used, see the MMC_VDD_* masks in * mmc/host.h @@ -42,37 +23,14 @@ struct dma_chan; * @gpio_wp: read this GPIO pin to see if the card is write protected * @gpio_cd: read this GPIO pin to detect card insertion * @cd_invert: true if the gpio_cd pin value is active low - * @capabilities: the capabilities of the block as implemented in - * this platform, signify anything MMC_CAP_* from mmc/host.h - * @capabilities2: more capabilities, MMC_CAP2_* from mmc/host.h - * @sigdir: a bit field indicating for what bits in the MMC bus the host - * should enable signal direction indication. - * @dma_filter: function used to select an appropriate RX and TX - * DMA channel to be used for DMA, if and only if you're deploying the - * generic DMA engine - * @dma_rx_param: parameter passed to the DMA allocation - * filter in order to select an appropriate RX channel. If - * there is a bidirectional RX+TX channel, then just specify - * this and leave dma_tx_param set to NULL - * @dma_tx_param: parameter passed to the DMA allocation - * filter in order to select an appropriate TX channel. If this - * is NULL the driver will attempt to use the RX channel as a - * bidirectional channel */ struct mmci_platform_data { - unsigned int f_max; unsigned int ocr_mask; int (*ios_handler)(struct device *, struct mmc_ios *); unsigned int (*status)(struct device *); int gpio_wp; int gpio_cd; bool cd_invert; - unsigned long capabilities; - unsigned long capabilities2; - u32 sigdir; - bool (*dma_filter)(struct dma_chan *chan, void *filter_param); - void *dma_rx_param; - void *dma_tx_param; }; #endif diff --git a/include/linux/amba/xilinx_dma.h b/include/linux/amba/xilinx_dma.h new file mode 100644 index 00000000000..34b98f276ed --- /dev/null +++ b/include/linux/amba/xilinx_dma.h @@ -0,0 +1,47 @@ +/* + * Xilinx DMA Engine drivers support header file + * + * Copyright (C) 2010-2014 Xilinx, Inc. All rights reserved. + * + * This is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __DMA_XILINX_DMA_H +#define __DMA_XILINX_DMA_H + +#include <linux/dma-mapping.h> +#include <linux/dmaengine.h> + +/** + * struct xilinx_vdma_config - VDMA Configuration structure + * @frm_dly: Frame delay + * @gen_lock: Whether in gen-lock mode + * @master: Master that it syncs to + * @frm_cnt_en: Enable frame count enable + * @park: Whether wants to park + * @park_frm: Frame to park on + * @coalesc: Interrupt coalescing threshold + * @delay: Delay counter + * @reset: Reset Channel + * @ext_fsync: External Frame Sync source + */ +struct xilinx_vdma_config { + int frm_dly; + int gen_lock; + int master; + int frm_cnt_en; + int park; + int park_frm; + int coalesc; + int delay; + int reset; + int ext_fsync; +}; + +int xilinx_vdma_channel_set_config(struct dma_chan *dchan, + struct xilinx_vdma_config *cfg); + +#endif |