diff options
Diffstat (limited to 'include/linux/amba')
| -rw-r--r-- | include/linux/amba/bus.h | 11 | ||||
| -rw-r--r-- | include/linux/amba/mmci.h | 10 | ||||
| -rw-r--r-- | include/linux/amba/serial.h | 3 |
3 files changed, 20 insertions, 4 deletions
diff --git a/include/linux/amba/bus.h b/include/linux/amba/bus.h index 8b103860783..b0c17401243 100644 --- a/include/linux/amba/bus.h +++ b/include/linux/amba/bus.h @@ -14,14 +14,19 @@ #ifndef ASMARM_AMBA_H #define ASMARM_AMBA_H +#include <linux/clk.h> #include <linux/device.h> +#include <linux/err.h> #include <linux/resource.h> #define AMBA_NR_IRQS 2 +struct clk; + struct amba_device { struct device dev; struct resource res; + struct clk *pclk; u64 dma_mask; unsigned int periphid; unsigned int irq[AMBA_NR_IRQS]; @@ -59,6 +64,12 @@ struct amba_device *amba_find_device(const char *, struct device *, unsigned int int amba_request_regions(struct amba_device *, const char *); void amba_release_regions(struct amba_device *); +#define amba_pclk_enable(d) \ + (IS_ERR((d)->pclk) ? 0 : clk_enable((d)->pclk)) + +#define amba_pclk_disable(d) \ + do { if (!IS_ERR((d)->pclk)) clk_disable((d)->pclk); } while (0) + #define amba_config(d) (((d)->periphid >> 24) & 0xff) #define amba_rev(d) (((d)->periphid >> 20) & 0x0f) #define amba_manf(d) (((d)->periphid >> 12) & 0xff) diff --git a/include/linux/amba/mmci.h b/include/linux/amba/mmci.h index 7e466fe7202..ca84ce70d5d 100644 --- a/include/linux/amba/mmci.h +++ b/include/linux/amba/mmci.h @@ -15,9 +15,10 @@ * @ocr_mask: available voltages on the 4 pins from the block, this * is ignored if a regulator is used, see the MMC_VDD_* masks in * mmc/host.h - * @translate_vdd: a callback function to translate a MMC_VDD_* - * mask into a value to be binary or:ed and written into the - * MMCIPWR register of the block + * @vdd_handler: a callback function to translate a MMC_VDD_* + * mask into a value to be binary (or set some other custom bits + * in MMCIPWR) or:ed and written into the MMCIPWR register of the + * block. May also control external power based on the power_mode. * @status: if no GPIO read function was given to the block in * gpio_wp (below) this function will be called to determine * whether a card is present in the MMC slot or not @@ -29,7 +30,8 @@ struct mmci_platform_data { unsigned int f_max; unsigned int ocr_mask; - u32 (*translate_vdd)(struct device *, unsigned int); + u32 (*vdd_handler)(struct device *, unsigned int vdd, + unsigned char power_mode); unsigned int (*status)(struct device *); int gpio_wp; int gpio_cd; diff --git a/include/linux/amba/serial.h b/include/linux/amba/serial.h index 5a5a7fd6249..e1b634b635f 100644 --- a/include/linux/amba/serial.h +++ b/include/linux/amba/serial.h @@ -38,10 +38,12 @@ #define UART01x_FR 0x18 /* Flag register (Read only). */ #define UART010_IIR 0x1C /* Interrupt indentification register (Read). */ #define UART010_ICR 0x1C /* Interrupt clear register (Write). */ +#define ST_UART011_LCRH_RX 0x1C /* Rx line control register. */ #define UART01x_ILPR 0x20 /* IrDA low power counter register. */ #define UART011_IBRD 0x24 /* Integer baud rate divisor register. */ #define UART011_FBRD 0x28 /* Fractional baud rate divisor register. */ #define UART011_LCRH 0x2c /* Line control register. */ +#define ST_UART011_LCRH_TX 0x2c /* Tx Line control register. */ #define UART011_CR 0x30 /* Control register. */ #define UART011_IFLS 0x34 /* Interrupt fifo level select. */ #define UART011_IMSC 0x38 /* Interrupt mask. */ @@ -84,6 +86,7 @@ #define UART010_CR_TIE 0x0020 #define UART010_CR_RIE 0x0010 #define UART010_CR_MSIE 0x0008 +#define ST_UART011_CR_OVSFACT 0x0008 /* Oversampling factor */ #define UART01x_CR_IIRLP 0x0004 /* SIR low power mode */ #define UART01x_CR_SIREN 0x0002 /* SIR enable */ #define UART01x_CR_UARTEN 0x0001 /* UART enable */ |