diff options
Diffstat (limited to 'include/linux/cyclades.h')
| -rw-r--r-- | include/linux/cyclades.h | 827 |
1 files changed, 827 insertions, 0 deletions
diff --git a/include/linux/cyclades.h b/include/linux/cyclades.h new file mode 100644 index 00000000000..46d8254c1a7 --- /dev/null +++ b/include/linux/cyclades.h @@ -0,0 +1,827 @@ +/* $Revision: 3.0 $$Date: 1998/11/02 14:20:59 $ + * linux/include/linux/cyclades.h + * + * This file was initially written by + * Randolph Bentson <bentson@grieg.seaslug.org> and is maintained by + * Ivan Passos <ivan@cyclades.com>. + * + * This file contains the general definitions for the cyclades.c driver + *$Log: cyclades.h,v $ + *Revision 3.1 2002/01/29 11:36:16 henrique + *added throttle field on struct cyclades_port to indicate whether the + *port is throttled or not + * + *Revision 3.1 2000/04/19 18:52:52 ivan + *converted address fields to unsigned long and added fields for physical + *addresses on cyclades_card structure; + * + *Revision 3.0 1998/11/02 14:20:59 ivan + *added nports field on cyclades_card structure; + * + *Revision 2.5 1998/08/03 16:57:01 ivan + *added cyclades_idle_stats structure; + * + *Revision 2.4 1998/06/01 12:09:53 ivan + *removed closing_wait2 from cyclades_port structure; + * + *Revision 2.3 1998/03/16 18:01:12 ivan + *changes in the cyclades_port structure to get it closer to the + *standard serial port structure; + *added constants for new ioctls; + * + *Revision 2.2 1998/02/17 16:50:00 ivan + *changes in the cyclades_port structure (addition of shutdown_wait and + *chip_rev variables); + *added constants for new ioctls and for CD1400 rev. numbers. + * + *Revision 2.1 1997/10/24 16:03:00 ivan + *added rflow (which allows enabling the CD1400 special flow control + *feature) and rtsdtr_inv (which allows DTR/RTS pin inversion) to + *cyclades_port structure; + *added Alpha support + * + *Revision 2.0 1997/06/30 10:30:00 ivan + *added some new doorbell command constants related to IOCTLW and + *UART error signaling + * + *Revision 1.8 1997/06/03 15:30:00 ivan + *added constant ZFIRM_HLT + *added constant CyPCI_Ze_win ( = 2 * Cy_PCI_Zwin) + * + *Revision 1.7 1997/03/26 10:30:00 daniel + *new entries at the end of cyclades_port struct to reallocate + *variables illegally allocated within card memory. + * + *Revision 1.6 1996/09/09 18:35:30 bentson + *fold in changes for Cyclom-Z -- including structures for + *communicating with board as well modest changes to original + *structures to support new features. + * + *Revision 1.5 1995/11/13 21:13:31 bentson + *changes suggested by Michael Chastain <mec@duracef.shout.net> + *to support use of this file in non-kernel applications + * + * + */ + +#ifndef _LINUX_CYCLADES_H +#define _LINUX_CYCLADES_H + +struct cyclades_monitor { + unsigned long int_count; + unsigned long char_count; + unsigned long char_max; + unsigned long char_last; +}; + +/* + * These stats all reflect activity since the device was last initialized. + * (i.e., since the port was opened with no other processes already having it + * open) + */ +struct cyclades_idle_stats { + time_t in_use; /* Time device has been in use (secs) */ + time_t recv_idle; /* Time since last char received (secs) */ + time_t xmit_idle; /* Time since last char transmitted (secs) */ + unsigned long recv_bytes; /* Bytes received */ + unsigned long xmit_bytes; /* Bytes transmitted */ + unsigned long overruns; /* Input overruns */ + unsigned long frame_errs; /* Input framing errors */ + unsigned long parity_errs; /* Input parity errors */ +}; + +#define CYCLADES_MAGIC 0x4359 + +#define CYGETMON 0x435901 +#define CYGETTHRESH 0x435902 +#define CYSETTHRESH 0x435903 +#define CYGETDEFTHRESH 0x435904 +#define CYSETDEFTHRESH 0x435905 +#define CYGETTIMEOUT 0x435906 +#define CYSETTIMEOUT 0x435907 +#define CYGETDEFTIMEOUT 0x435908 +#define CYSETDEFTIMEOUT 0x435909 +#define CYSETRFLOW 0x43590a +#define CYGETRFLOW 0x43590b +#define CYSETRTSDTR_INV 0x43590c +#define CYGETRTSDTR_INV 0x43590d +#define CYZSETPOLLCYCLE 0x43590e +#define CYZGETPOLLCYCLE 0x43590f +#define CYGETCD1400VER 0x435910 +#define CYGETCARDINFO 0x435911 +#define CYSETWAIT 0x435912 +#define CYGETWAIT 0x435913 + +/*************** CYCLOM-Z ADDITIONS ***************/ + +#define CZIOC ('M' << 8) +#define CZ_NBOARDS (CZIOC|0xfa) +#define CZ_BOOT_START (CZIOC|0xfb) +#define CZ_BOOT_DATA (CZIOC|0xfc) +#define CZ_BOOT_END (CZIOC|0xfd) +#define CZ_TEST (CZIOC|0xfe) + +#define CZ_DEF_POLL (HZ/25) + +#define MAX_BOARD 4 /* Max number of boards */ +#define MAX_DEV 256 /* Max number of ports total */ +#define CYZ_MAX_SPEED 921600 + +#define CYZ_FIFO_SIZE 16 + +#define CYZ_BOOT_NWORDS 0x100 +struct CYZ_BOOT_CTRL { + unsigned short nboard; + int status[MAX_BOARD]; + int nchannel[MAX_BOARD]; + int fw_rev[MAX_BOARD]; + unsigned long offset; + unsigned long data[CYZ_BOOT_NWORDS]; +}; + + +#ifndef DP_WINDOW_SIZE +/* #include "cyclomz.h" */ +/****************** ****************** *******************/ +/* + * The data types defined below are used in all ZFIRM interface + * data structures. They accomodate differences between HW + * architectures and compilers. + */ + +#if defined(__alpha__) +typedef unsigned long ucdouble; /* 64 bits, unsigned */ +typedef unsigned int uclong; /* 32 bits, unsigned */ +#else +typedef unsigned long uclong; /* 32 bits, unsigned */ +#endif +typedef unsigned short ucshort; /* 16 bits, unsigned */ +typedef unsigned char ucchar; /* 8 bits, unsigned */ + +/* + * Memory Window Sizes + */ + +#define DP_WINDOW_SIZE (0x00080000) /* window size 512 Kb */ +#define ZE_DP_WINDOW_SIZE (0x00100000) /* window size 1 Mb (Ze and + 8Zo V.2 */ +#define CTRL_WINDOW_SIZE (0x00000080) /* runtime regs 128 bytes */ + +/* + * CUSTOM_REG - Cyclom-Z/PCI Custom Registers Set. The driver + * normally will access only interested on the fpga_id, fpga_version, + * start_cpu and stop_cpu. + */ + +struct CUSTOM_REG { + uclong fpga_id; /* FPGA Identification Register */ + uclong fpga_version; /* FPGA Version Number Register */ + uclong cpu_start; /* CPU start Register (write) */ + uclong cpu_stop; /* CPU stop Register (write) */ + uclong misc_reg; /* Miscelaneous Register */ + uclong idt_mode; /* IDT mode Register */ + uclong uart_irq_status; /* UART IRQ status Register */ + uclong clear_timer0_irq; /* Clear timer interrupt Register */ + uclong clear_timer1_irq; /* Clear timer interrupt Register */ + uclong clear_timer2_irq; /* Clear timer interrupt Register */ + uclong test_register; /* Test Register */ + uclong test_count; /* Test Count Register */ + uclong timer_select; /* Timer select register */ + uclong pr_uart_irq_status; /* Prioritized UART IRQ stat Reg */ + uclong ram_wait_state; /* RAM wait-state Register */ + uclong uart_wait_state; /* UART wait-state Register */ + uclong timer_wait_state; /* timer wait-state Register */ + uclong ack_wait_state; /* ACK wait State Register */ +}; + +/* + * RUNTIME_9060 - PLX PCI9060ES local configuration and shared runtime + * registers. This structure can be used to access the 9060 registers + * (memory mapped). + */ + +struct RUNTIME_9060 { + uclong loc_addr_range; /* 00h - Local Address Range */ + uclong loc_addr_base; /* 04h - Local Address Base */ + uclong loc_arbitr; /* 08h - Local Arbitration */ + uclong endian_descr; /* 0Ch - Big/Little Endian Descriptor */ + uclong loc_rom_range; /* 10h - Local ROM Range */ + uclong loc_rom_base; /* 14h - Local ROM Base */ + uclong loc_bus_descr; /* 18h - Local Bus descriptor */ + uclong loc_range_mst; /* 1Ch - Local Range for Master to PCI */ + uclong loc_base_mst; /* 20h - Local Base for Master PCI */ + uclong loc_range_io; /* 24h - Local Range for Master IO */ + uclong pci_base_mst; /* 28h - PCI Base for Master PCI */ + uclong pci_conf_io; /* 2Ch - PCI configuration for Master IO */ + uclong filler1; /* 30h */ + uclong filler2; /* 34h */ + uclong filler3; /* 38h */ + uclong filler4; /* 3Ch */ + uclong mail_box_0; /* 40h - Mail Box 0 */ + uclong mail_box_1; /* 44h - Mail Box 1 */ + uclong mail_box_2; /* 48h - Mail Box 2 */ + uclong mail_box_3; /* 4Ch - Mail Box 3 */ + uclong filler5; /* 50h */ + uclong filler6; /* 54h */ + uclong filler7; /* 58h */ + uclong filler8; /* 5Ch */ + uclong pci_doorbell; /* 60h - PCI to Local Doorbell */ + uclong loc_doorbell; /* 64h - Local to PCI Doorbell */ + uclong intr_ctrl_stat; /* 68h - Interrupt Control/Status */ + uclong init_ctrl; /* 6Ch - EEPROM control, Init Control, etc */ +}; + +/* Values for the Local Base Address re-map register */ + +#define WIN_RAM 0x00000001L /* set the sliding window to RAM */ +#define WIN_CREG 0x14000001L /* set the window to custom Registers */ + +/* Values timer select registers */ + +#define TIMER_BY_1M 0x00 /* clock divided by 1M */ +#define TIMER_BY_256K 0x01 /* clock divided by 256k */ +#define TIMER_BY_128K 0x02 /* clock divided by 128k */ +#define TIMER_BY_32K 0x03 /* clock divided by 32k */ + +/****************** ****************** *******************/ +#endif + +#ifndef ZFIRM_ID +/* #include "zfwint.h" */ +/****************** ****************** *******************/ +/* + * This file contains the definitions for interfacing with the + * Cyclom-Z ZFIRM Firmware. + */ + +/* General Constant definitions */ + +#define MAX_CHAN 64 /* max number of channels per board */ + +/* firmware id structure (set after boot) */ + +#define ID_ADDRESS 0x00000180L /* signature/pointer address */ +#define ZFIRM_ID 0x5557465AL /* ZFIRM/U signature */ +#define ZFIRM_HLT 0x59505B5CL /* ZFIRM needs external power supply */ +#define ZFIRM_RST 0x56040674L /* RST signal (due to FW reset) */ + +#define ZF_TINACT_DEF 1000 /* default inactivity timeout + (1000 ms) */ +#define ZF_TINACT ZF_TINACT_DEF + +struct FIRM_ID { + uclong signature; /* ZFIRM/U signature */ + uclong zfwctrl_addr; /* pointer to ZFW_CTRL structure */ +}; + +/* Op. System id */ + +#define C_OS_LINUX 0x00000030 /* generic Linux system */ + +/* channel op_mode */ + +#define C_CH_DISABLE 0x00000000 /* channel is disabled */ +#define C_CH_TXENABLE 0x00000001 /* channel Tx enabled */ +#define C_CH_RXENABLE 0x00000002 /* channel Rx enabled */ +#define C_CH_ENABLE 0x00000003 /* channel Tx/Rx enabled */ +#define C_CH_LOOPBACK 0x00000004 /* Loopback mode */ + +/* comm_parity - parity */ + +#define C_PR_NONE 0x00000000 /* None */ +#define C_PR_ODD 0x00000001 /* Odd */ +#define C_PR_EVEN 0x00000002 /* Even */ +#define C_PR_MARK 0x00000004 /* Mark */ +#define C_PR_SPACE 0x00000008 /* Space */ +#define C_PR_PARITY 0x000000ff + +#define C_PR_DISCARD 0x00000100 /* discard char with frame/par error */ +#define C_PR_IGNORE 0x00000200 /* ignore frame/par error */ + +/* comm_data_l - data length and stop bits */ + +#define C_DL_CS5 0x00000001 +#define C_DL_CS6 0x00000002 +#define C_DL_CS7 0x00000004 +#define C_DL_CS8 0x00000008 +#define C_DL_CS 0x0000000f +#define C_DL_1STOP 0x00000010 +#define C_DL_15STOP 0x00000020 +#define C_DL_2STOP 0x00000040 +#define C_DL_STOP 0x000000f0 + +/* interrupt enabling/status */ + +#define C_IN_DISABLE 0x00000000 /* zero, disable interrupts */ +#define C_IN_TXBEMPTY 0x00000001 /* tx buffer empty */ +#define C_IN_TXLOWWM 0x00000002 /* tx buffer below LWM */ +#define C_IN_RXHIWM 0x00000010 /* rx buffer above HWM */ +#define C_IN_RXNNDT 0x00000020 /* rx no new data timeout */ +#define C_IN_MDCD 0x00000100 /* modem DCD change */ +#define C_IN_MDSR 0x00000200 /* modem DSR change */ +#define C_IN_MRI 0x00000400 /* modem RI change */ +#define C_IN_MCTS 0x00000800 /* modem CTS change */ +#define C_IN_RXBRK 0x00001000 /* Break received */ +#define C_IN_PR_ERROR 0x00002000 /* parity error */ +#define C_IN_FR_ERROR 0x00004000 /* frame error */ +#define C_IN_OVR_ERROR 0x00008000 /* overrun error */ +#define C_IN_RXOFL 0x00010000 /* RX buffer overflow */ +#define C_IN_IOCTLW 0x00020000 /* I/O control w/ wait */ +#define C_IN_MRTS 0x00040000 /* modem RTS drop */ +#define C_IN_ICHAR 0x00080000 + +/* flow control */ + +#define C_FL_OXX 0x00000001 /* output Xon/Xoff flow control */ +#define C_FL_IXX 0x00000002 /* output Xon/Xoff flow control */ +#define C_FL_OIXANY 0x00000004 /* output Xon/Xoff (any xon) */ +#define C_FL_SWFLOW 0x0000000f + +/* flow status */ + +#define C_FS_TXIDLE 0x00000000 /* no Tx data in the buffer or UART */ +#define C_FS_SENDING 0x00000001 /* UART is sending data */ +#define C_FS_SWFLOW 0x00000002 /* Tx is stopped by received Xoff */ + +/* rs_control/rs_status RS-232 signals */ + +#define C_RS_PARAM 0x80000000 /* Indicates presence of parameter in + IOCTLM command */ +#define C_RS_RTS 0x00000001 /* RTS */ +#define C_RS_DTR 0x00000004 /* DTR */ +#define C_RS_DCD 0x00000100 /* CD */ +#define C_RS_DSR 0x00000200 /* DSR */ +#define C_RS_RI 0x00000400 /* RI */ +#define C_RS_CTS 0x00000800 /* CTS */ + +/* commands Host <-> Board */ + +#define C_CM_RESET 0x01 /* reset/flush buffers */ +#define C_CM_IOCTL 0x02 /* re-read CH_CTRL */ +#define C_CM_IOCTLW 0x03 /* re-read CH_CTRL, intr when done */ +#define C_CM_IOCTLM 0x04 /* RS-232 outputs change */ +#define C_CM_SENDXOFF 0x10 /* send Xoff */ +#define C_CM_SENDXON 0x11 /* send Xon */ +#define C_CM_CLFLOW 0x12 /* Clear flow control (resume) */ +#define C_CM_SENDBRK 0x41 /* send break */ +#define C_CM_INTBACK 0x42 /* Interrupt back */ +#define C_CM_SET_BREAK 0x43 /* Tx break on */ +#define C_CM_CLR_BREAK 0x44 /* Tx break off */ +#define C_CM_CMD_DONE 0x45 /* Previous command done */ +#define C_CM_INTBACK2 0x46 /* Alternate Interrupt back */ +#define C_CM_TINACT 0x51 /* set inactivity detection */ +#define C_CM_IRQ_ENBL 0x52 /* enable generation of interrupts */ +#define C_CM_IRQ_DSBL 0x53 /* disable generation of interrupts */ +#define C_CM_ACK_ENBL 0x54 /* enable acknowledged interrupt mode */ +#define C_CM_ACK_DSBL 0x55 /* disable acknowledged intr mode */ +#define C_CM_FLUSH_RX 0x56 /* flushes Rx buffer */ +#define C_CM_FLUSH_TX 0x57 /* flushes Tx buffer */ +#define C_CM_Q_ENABLE 0x58 /* enables queue access from the + driver */ +#define C_CM_Q_DISABLE 0x59 /* disables queue access from the + driver */ + +#define C_CM_TXBEMPTY 0x60 /* Tx buffer is empty */ +#define C_CM_TXLOWWM 0x61 /* Tx buffer low water mark */ +#define C_CM_RXHIWM 0x62 /* Rx buffer high water mark */ +#define C_CM_RXNNDT 0x63 /* rx no new data timeout */ +#define C_CM_TXFEMPTY 0x64 +#define C_CM_ICHAR 0x65 +#define C_CM_MDCD 0x70 /* modem DCD change */ +#define C_CM_MDSR 0x71 /* modem DSR change */ +#define C_CM_MRI 0x72 /* modem RI change */ +#define C_CM_MCTS 0x73 /* modem CTS change */ +#define C_CM_MRTS 0x74 /* modem RTS drop */ +#define C_CM_RXBRK 0x84 /* Break received */ +#define C_CM_PR_ERROR 0x85 /* Parity error */ +#define C_CM_FR_ERROR 0x86 /* Frame error */ +#define C_CM_OVR_ERROR 0x87 /* Overrun error */ +#define C_CM_RXOFL 0x88 /* RX buffer overflow */ +#define C_CM_CMDERROR 0x90 /* command error */ +#define C_CM_FATAL 0x91 /* fatal error */ +#define C_CM_HW_RESET 0x92 /* reset board */ + +/* + * CH_CTRL - This per port structure contains all parameters + * that control an specific port. It can be seen as the + * configuration registers of a "super-serial-controller". + */ + +struct CH_CTRL { + uclong op_mode; /* operation mode */ + uclong intr_enable; /* interrupt masking */ + uclong sw_flow; /* SW flow control */ + uclong flow_status; /* output flow status */ + uclong comm_baud; /* baud rate - numerically specified */ + uclong comm_parity; /* parity */ + uclong comm_data_l; /* data length/stop */ + uclong comm_flags; /* other flags */ + uclong hw_flow; /* HW flow control */ + uclong rs_control; /* RS-232 outputs */ + uclong rs_status; /* RS-232 inputs */ + uclong flow_xon; /* xon char */ + uclong flow_xoff; /* xoff char */ + uclong hw_overflow; /* hw overflow counter */ + uclong sw_overflow; /* sw overflow counter */ + uclong comm_error; /* frame/parity error counter */ + uclong ichar; + uclong filler[7]; +}; + + +/* + * BUF_CTRL - This per channel structure contains + * all Tx and Rx buffer control for a given channel. + */ + +struct BUF_CTRL { + uclong flag_dma; /* buffers are in Host memory */ + uclong tx_bufaddr; /* address of the tx buffer */ + uclong tx_bufsize; /* tx buffer size */ + uclong tx_threshold; /* tx low water mark */ + uclong tx_get; /* tail index tx buf */ + uclong tx_put; /* head index tx buf */ + uclong rx_bufaddr; /* address of the rx buffer */ + uclong rx_bufsize; /* rx buffer size */ + uclong rx_threshold; /* rx high water mark */ + uclong rx_get; /* tail index rx buf */ + uclong rx_put; /* head index rx buf */ + uclong filler[5]; /* filler to align structures */ +}; + +/* + * BOARD_CTRL - This per board structure contains all global + * control fields related to the board. + */ + +struct BOARD_CTRL { + + /* static info provided by the on-board CPU */ + uclong n_channel; /* number of channels */ + uclong fw_version; /* firmware version */ + + /* static info provided by the driver */ + uclong op_system; /* op_system id */ + uclong dr_version; /* driver version */ + + /* board control area */ + uclong inactivity; /* inactivity control */ + + /* host to FW commands */ + uclong hcmd_channel; /* channel number */ + uclong hcmd_param; /* pointer to parameters */ + + /* FW to Host commands */ + uclong fwcmd_channel; /* channel number */ + uclong fwcmd_param; /* pointer to parameters */ + uclong zf_int_queue_addr; /* offset for INT_QUEUE structure */ + + /* filler so the structures are aligned */ + uclong filler[6]; +}; + +/* Host Interrupt Queue */ + +#define QUEUE_SIZE (10*MAX_CHAN) + +struct INT_QUEUE { + unsigned char intr_code[QUEUE_SIZE]; + unsigned long channel[QUEUE_SIZE]; + unsigned long param[QUEUE_SIZE]; + unsigned long put; + unsigned long get; +}; + +/* + * ZFW_CTRL - This is the data structure that includes all other + * data structures used by the Firmware. + */ + +struct ZFW_CTRL { + struct BOARD_CTRL board_ctrl; + struct CH_CTRL ch_ctrl[MAX_CHAN]; + struct BUF_CTRL buf_ctrl[MAX_CHAN]; +}; + +/****************** ****************** *******************/ +#endif + +/* Per card data structure */ +struct resource; +struct cyclades_card { + unsigned long base_phys; + unsigned long ctl_phys; + void __iomem *base_addr; + void __iomem *ctl_addr; + int irq; + int num_chips; /* 0 if card absent, -1 if Z/PCI, else Y */ + int first_line; /* minor number of first channel on card */ + int nports; /* Number of ports in the card */ + int bus_index; /* address shift - 0 for ISA, 1 for PCI */ + int intr_enabled; /* FW Interrupt flag - 0 disabled, 1 enabled */ + struct pci_dev *pdev; +#ifdef __KERNEL__ + spinlock_t card_lock; +#else + unsigned long filler; +#endif +}; + +struct cyclades_chip { + int filler; +}; + + +#ifdef __KERNEL__ + +/*************************************** + * Memory access functions/macros * + * (required to support Alpha systems) * + ***************************************/ + +#define cy_writeb(port,val) {writeb((val),(port)); mb();} +#define cy_writew(port,val) {writew((val),(port)); mb();} +#define cy_writel(port,val) {writel((val),(port)); mb();} + +#define cy_readb(port) readb(port) +#define cy_readw(port) readw(port) +#define cy_readl(port) readl(port) + +/* + * Statistics counters + */ +struct cyclades_icount { + __u32 cts, dsr, rng, dcd, tx, rx; + __u32 frame, parity, overrun, brk; + __u32 buf_overrun; +}; + +/* + * This is our internal structure for each serial port's state. + * + * Many fields are paralleled by the structure used by the serial_struct + * structure. + * + * For definitions of the flags field, see tty.h + */ + +struct cyclades_port { + int magic; + int card; + int line; + int flags; /* defined in tty.h */ + int type; /* UART type */ + struct tty_struct *tty; + int read_status_mask; + int ignore_status_mask; + int timeout; + int xmit_fifo_size; + int cor1,cor2,cor3,cor4,cor5; + int tbpr,tco,rbpr,rco; + int baud; + int rflow; + int rtsdtr_inv; + int chip_rev; + int custom_divisor; + int x_char; /* to be pushed out ASAP */ + int close_delay; + unsigned short closing_wait; + unsigned long event; + unsigned long last_active; + int count; /* # of fd on device */ + int breakon; + int breakoff; + int blocked_open; /* # of blocked opens */ + unsigned char *xmit_buf; + int xmit_head; + int xmit_tail; + int xmit_cnt; + int default_threshold; + int default_timeout; + unsigned long jiffies[3]; + unsigned long rflush_count; + struct cyclades_monitor mon; + struct cyclades_idle_stats idle_stats; + struct cyclades_icount icount; + struct work_struct tqueue; + wait_queue_head_t open_wait; + wait_queue_head_t close_wait; + wait_queue_head_t shutdown_wait; + wait_queue_head_t delta_msr_wait; + int throttle; +}; + +/* + * Events are used to schedule things to happen at timer-interrupt + * time, instead of at cy interrupt time. + */ +#define Cy_EVENT_READ_PROCESS 0 +#define Cy_EVENT_WRITE_WAKEUP 1 +#define Cy_EVENT_HANGUP 2 +#define Cy_EVENT_BREAK 3 +#define Cy_EVENT_OPEN_WAKEUP 4 +#define Cy_EVENT_SHUTDOWN_WAKEUP 5 +#define Cy_EVENT_DELTA_WAKEUP 6 +#define Cy_EVENT_Z_RX_FULL 7 + +#define CLOSING_WAIT_DELAY 30*HZ +#define CY_CLOSING_WAIT_NONE 65535 +#define CY_CLOSING_WAIT_INF 0 + + +#define CyMAX_CHIPS_PER_CARD 8 +#define CyMAX_CHAR_FIFO 12 +#define CyPORTS_PER_CHIP 4 +#define CD1400_MAX_SPEED 115200 + +#define CyISA_Ywin 0x2000 + +#define CyPCI_Ywin 0x4000 +#define CyPCI_Yctl 0x80 +#define CyPCI_Zctl CTRL_WINDOW_SIZE +#define CyPCI_Zwin 0x80000 +#define CyPCI_Ze_win (2 * CyPCI_Zwin) + +#define PCI_DEVICE_ID_MASK 0x06 + +/**** CD1400 registers ****/ + +#define CD1400_REV_G 0x46 +#define CD1400_REV_J 0x48 + +#define CyRegSize 0x0400 +#define Cy_HwReset 0x1400 +#define Cy_ClrIntr 0x1800 +#define Cy_EpldRev 0x1e00 + +/* Global Registers */ + +#define CyGFRCR (0x40*2) +#define CyRevE (44) +#define CyCAR (0x68*2) +#define CyCHAN_0 (0x00) +#define CyCHAN_1 (0x01) +#define CyCHAN_2 (0x02) +#define CyCHAN_3 (0x03) +#define CyGCR (0x4B*2) +#define CyCH0_SERIAL (0x00) +#define CyCH0_PARALLEL (0x80) +#define CySVRR (0x67*2) +#define CySRModem (0x04) +#define CySRTransmit (0x02) +#define CySRReceive (0x01) +#define CyRICR (0x44*2) +#define CyTICR (0x45*2) +#define CyMICR (0x46*2) +#define CyICR0 (0x00) +#define CyICR1 (0x01) +#define CyICR2 (0x02) +#define CyICR3 (0x03) +#define CyRIR (0x6B*2) +#define CyTIR (0x6A*2) +#define CyMIR (0x69*2) +#define CyIRDirEq (0x80) +#define CyIRBusy (0x40) +#define CyIRUnfair (0x20) +#define CyIRContext (0x1C) +#define CyIRChannel (0x03) +#define CyPPR (0x7E*2) +#define CyCLOCK_20_1MS (0x27) +#define CyCLOCK_25_1MS (0x31) +#define CyCLOCK_25_5MS (0xf4) +#define CyCLOCK_60_1MS (0x75) +#define CyCLOCK_60_2MS (0xea) + +/* Virtual Registers */ + +#define CyRIVR (0x43*2) +#define CyTIVR (0x42*2) +#define CyMIVR (0x41*2) +#define CyIVRMask (0x07) +#define CyIVRRxEx (0x07) +#define CyIVRRxOK (0x03) +#define CyIVRTxOK (0x02) +#define CyIVRMdmOK (0x01) +#define CyTDR (0x63*2) +#define CyRDSR (0x62*2) +#define CyTIMEOUT (0x80) +#define CySPECHAR (0x70) +#define CyBREAK (0x08) +#define CyPARITY (0x04) +#define CyFRAME (0x02) +#define CyOVERRUN (0x01) +#define CyMISR (0x4C*2) +/* see CyMCOR_ and CyMSVR_ for bits*/ +#define CyEOSRR (0x60*2) + +/* Channel Registers */ + +#define CyLIVR (0x18*2) +#define CyMscsr (0x01) +#define CyTdsr (0x02) +#define CyRgdsr (0x03) +#define CyRedsr (0x07) +#define CyCCR (0x05*2) +/* Format 1 */ +#define CyCHAN_RESET (0x80) +#define CyCHIP_RESET (0x81) +#define CyFlushTransFIFO (0x82) +/* Format 2 */ +#define CyCOR_CHANGE (0x40) +#define CyCOR1ch (0x02) +#define CyCOR2ch (0x04) +#define CyCOR3ch (0x08) +/* Format 3 */ +#define CySEND_SPEC_1 (0x21) +#define CySEND_SPEC_2 (0x22) +#define CySEND_SPEC_3 (0x23) +#define CySEND_SPEC_4 (0x24) +/* Format 4 */ +#define CyCHAN_CTL (0x10) +#define CyDIS_RCVR (0x01) +#define CyENB_RCVR (0x02) +#define CyDIS_XMTR (0x04) +#define CyENB_XMTR (0x08) +#define CySRER (0x06*2) +#define CyMdmCh (0x80) +#define CyRxData (0x10) +#define CyTxRdy (0x04) +#define CyTxMpty (0x02) +#define CyNNDT (0x01) +#define CyCOR1 (0x08*2) +#define CyPARITY_NONE (0x00) +#define CyPARITY_0 (0x20) +#define CyPARITY_1 (0xA0) +#define CyPARITY_E (0x40) +#define CyPARITY_O (0xC0) +#define Cy_1_STOP (0x00) +#define Cy_1_5_STOP (0x04) +#define Cy_2_STOP (0x08) +#define Cy_5_BITS (0x00) +#define Cy_6_BITS (0x01) +#define Cy_7_BITS (0x02) +#define Cy_8_BITS (0x03) +#define CyCOR2 (0x09*2) +#define CyIXM (0x80) +#define CyTxIBE (0x40) +#define CyETC (0x20) +#define CyAUTO_TXFL (0x60) +#define CyLLM (0x10) +#define CyRLM (0x08) +#define CyRtsAO (0x04) +#define CyCtsAE (0x02) +#define CyDsrAE (0x01) +#define CyCOR3 (0x0A*2) +#define CySPL_CH_DRANGE (0x80) /* special character detect range */ +#define CySPL_CH_DET1 (0x40) /* enable special character detection + on SCHR4-SCHR3 */ +#define CyFL_CTRL_TRNSP (0x20) /* Flow Control Transparency */ +#define CySPL_CH_DET2 (0x10) /* Enable special character detection + on SCHR2-SCHR1 */ +#define CyREC_FIFO (0x0F) /* Receive FIFO threshold */ +#define CyCOR4 (0x1E*2) +#define CyCOR5 (0x1F*2) +#define CyCCSR (0x0B*2) +#define CyRxEN (0x80) +#define CyRxFloff (0x40) +#define CyRxFlon (0x20) +#define CyTxEN (0x08) +#define CyTxFloff (0x04) +#define CyTxFlon (0x02) +#define CyRDCR (0x0E*2) +#define CySCHR1 (0x1A*2) +#define CySCHR2 (0x1B*2) +#define CySCHR3 (0x1C*2) +#define CySCHR4 (0x1D*2) +#define CySCRL (0x22*2) +#define CySCRH (0x23*2) +#define CyLNC (0x24*2) +#define CyMCOR1 (0x15*2) +#define CyMCOR2 (0x16*2) +#define CyRTPR (0x21*2) +#define CyMSVR1 (0x6C*2) +#define CyMSVR2 (0x6D*2) +#define CyANY_DELTA (0xF0) +#define CyDSR (0x80) +#define CyCTS (0x40) +#define CyRI (0x20) +#define CyDCD (0x10) +#define CyDTR (0x02) +#define CyRTS (0x01) +#define CyPVSR (0x6F*2) +#define CyRBPR (0x78*2) +#define CyRCOR (0x7C*2) +#define CyTBPR (0x72*2) +#define CyTCOR (0x76*2) + +/* Custom Registers */ + +#define CyPLX_VER (0x3400) +#define PLX_9050 0x0b +#define PLX_9060 0x0c +#define PLX_9080 0x0d + +/***************************************************************************/ + +#endif /* __KERNEL__ */ +#endif /* _LINUX_CYCLADES_H */ |