diff options
Diffstat (limited to 'include/linux/fdreg.h')
| -rw-r--r-- | include/linux/fdreg.h | 137 |
1 files changed, 137 insertions, 0 deletions
diff --git a/include/linux/fdreg.h b/include/linux/fdreg.h new file mode 100644 index 00000000000..c2eeb63b72d --- /dev/null +++ b/include/linux/fdreg.h @@ -0,0 +1,137 @@ +#ifndef _LINUX_FDREG_H +#define _LINUX_FDREG_H +/* + * This file contains some defines for the floppy disk controller. + * Various sources. Mostly "IBM Microcomputers: A Programmers + * Handbook", Sanches and Canton. + */ + +#ifdef FDPATCHES +#define FD_IOPORT fdc_state[fdc].address +#else +/* It would be a lot saner just to force fdc_state[fdc].address to always + be set ! FIXME */ +#define FD_IOPORT 0x3f0 +#endif + +/* Fd controller regs. S&C, about page 340 */ +#define FD_STATUS (4 + FD_IOPORT ) +#define FD_DATA (5 + FD_IOPORT ) + +/* Digital Output Register */ +#define FD_DOR (2 + FD_IOPORT ) + +/* Digital Input Register (read) */ +#define FD_DIR (7 + FD_IOPORT ) + +/* Diskette Control Register (write)*/ +#define FD_DCR (7 + FD_IOPORT ) + +/* Bits of main status register */ +#define STATUS_BUSYMASK 0x0F /* drive busy mask */ +#define STATUS_BUSY 0x10 /* FDC busy */ +#define STATUS_DMA 0x20 /* 0- DMA mode */ +#define STATUS_DIR 0x40 /* 0- cpu->fdc */ +#define STATUS_READY 0x80 /* Data reg ready */ + +/* Bits of FD_ST0 */ +#define ST0_DS 0x03 /* drive select mask */ +#define ST0_HA 0x04 /* Head (Address) */ +#define ST0_NR 0x08 /* Not Ready */ +#define ST0_ECE 0x10 /* Equipment check error */ +#define ST0_SE 0x20 /* Seek end */ +#define ST0_INTR 0xC0 /* Interrupt code mask */ + +/* Bits of FD_ST1 */ +#define ST1_MAM 0x01 /* Missing Address Mark */ +#define ST1_WP 0x02 /* Write Protect */ +#define ST1_ND 0x04 /* No Data - unreadable */ +#define ST1_OR 0x10 /* OverRun */ +#define ST1_CRC 0x20 /* CRC error in data or addr */ +#define ST1_EOC 0x80 /* End Of Cylinder */ + +/* Bits of FD_ST2 */ +#define ST2_MAM 0x01 /* Missing Address Mark (again) */ +#define ST2_BC 0x02 /* Bad Cylinder */ +#define ST2_SNS 0x04 /* Scan Not Satisfied */ +#define ST2_SEH 0x08 /* Scan Equal Hit */ +#define ST2_WC 0x10 /* Wrong Cylinder */ +#define ST2_CRC 0x20 /* CRC error in data field */ +#define ST2_CM 0x40 /* Control Mark = deleted */ + +/* Bits of FD_ST3 */ +#define ST3_HA 0x04 /* Head (Address) */ +#define ST3_DS 0x08 /* drive is double-sided */ +#define ST3_TZ 0x10 /* Track Zero signal (1=track 0) */ +#define ST3_RY 0x20 /* drive is ready */ +#define ST3_WP 0x40 /* Write Protect */ +#define ST3_FT 0x80 /* Drive Fault */ + +/* Values for FD_COMMAND */ +#define FD_RECALIBRATE 0x07 /* move to track 0 */ +#define FD_SEEK 0x0F /* seek track */ +#define FD_READ 0xE6 /* read with MT, MFM, SKip deleted */ +#define FD_WRITE 0xC5 /* write with MT, MFM */ +#define FD_SENSEI 0x08 /* Sense Interrupt Status */ +#define FD_SPECIFY 0x03 /* specify HUT etc */ +#define FD_FORMAT 0x4D /* format one track */ +#define FD_VERSION 0x10 /* get version code */ +#define FD_CONFIGURE 0x13 /* configure FIFO operation */ +#define FD_PERPENDICULAR 0x12 /* perpendicular r/w mode */ +#define FD_GETSTATUS 0x04 /* read ST3 */ +#define FD_DUMPREGS 0x0E /* dump the contents of the fdc regs */ +#define FD_READID 0xEA /* prints the header of a sector */ +#define FD_UNLOCK 0x14 /* Fifo config unlock */ +#define FD_LOCK 0x94 /* Fifo config lock */ +#define FD_RSEEK_OUT 0x8f /* seek out (i.e. to lower tracks) */ +#define FD_RSEEK_IN 0xcf /* seek in (i.e. to higher tracks) */ + +/* the following commands are new in the 82078. They are not used in the + * floppy driver, except the first three. These commands may be useful for apps + * which use the FDRAWCMD interface. For doc, get the 82078 spec sheets at + * http://www-techdoc.intel.com/docs/periph/fd_contr/datasheets/ */ + +#define FD_PARTID 0x18 /* part id ("extended" version cmd) */ +#define FD_SAVE 0x2e /* save fdc regs for later restore */ +#define FD_DRIVESPEC 0x8e /* drive specification: Access to the + * 2 Mbps data transfer rate for tape + * drives */ + +#define FD_RESTORE 0x4e /* later restore */ +#define FD_POWERDOWN 0x27 /* configure FDC's powersave features */ +#define FD_FORMAT_N_WRITE 0xef /* format and write in one go. */ +#define FD_OPTION 0x33 /* ISO format (which is a clean way to + * pack more sectors on a track) */ + +/* DMA commands */ +#define DMA_READ 0x46 +#define DMA_WRITE 0x4A + +/* FDC version return types */ +#define FDC_NONE 0x00 +#define FDC_UNKNOWN 0x10 /* DO NOT USE THIS TYPE EXCEPT IF IDENTIFICATION + FAILS EARLY */ +#define FDC_8272A 0x20 /* Intel 8272a, NEC 765 */ +#define FDC_765ED 0x30 /* Non-Intel 1MB-compatible FDC, can't detect */ +#define FDC_82072 0x40 /* Intel 82072; 8272a + FIFO + DUMPREGS */ +#define FDC_82072A 0x45 /* 82072A (on Sparcs) */ +#define FDC_82077_ORIG 0x51 /* Original version of 82077AA, sans LOCK */ +#define FDC_82077 0x52 /* 82077AA-1 */ +#define FDC_82078_UNKN 0x5f /* Unknown 82078 variant */ +#define FDC_82078 0x60 /* 44pin 82078 or 64pin 82078SL */ +#define FDC_82078_1 0x61 /* 82078-1 (2Mbps fdc) */ +#define FDC_S82078B 0x62 /* S82078B (first seen on Adaptec AVA-2825 VLB + * SCSI/EIDE/Floppy controller) */ +#define FDC_87306 0x63 /* National Semiconductor PC 87306 */ + +/* + * Beware: the fdc type list is roughly sorted by increasing features. + * Presence of features is tested by comparing the FDC version id with the + * "oldest" version that has the needed feature. + * If during FDC detection, an obscure test fails late in the sequence, don't + * assign FDC_UNKNOWN. Else the FDC will be treated as a dumb 8272a, or worse. + * This is especially true if the tests are unneeded. + */ + +#define FD_RESET_DELAY 20 +#endif |