diff options
Diffstat (limited to 'include/linux/input')
| -rw-r--r-- | include/linux/input/adxl34x.h | 349 | ||||
| -rw-r--r-- | include/linux/input/cy8ctmg110_pdata.h | 10 | ||||
| -rw-r--r-- | include/linux/input/matrix_keypad.h | 6 |
3 files changed, 365 insertions, 0 deletions
diff --git a/include/linux/input/adxl34x.h b/include/linux/input/adxl34x.h new file mode 100644 index 00000000000..df00d998a44 --- /dev/null +++ b/include/linux/input/adxl34x.h @@ -0,0 +1,349 @@ +/* + * include/linux/input/adxl34x.h + * + * Digital Accelerometer characteristics are highly application specific + * and may vary between boards and models. The platform_data for the + * device's "struct device" holds this information. + * + * Copyright 2009 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef __LINUX_INPUT_ADXL34X_H__ +#define __LINUX_INPUT_ADXL34X_H__ + +struct adxl34x_platform_data { + + /* + * X,Y,Z Axis Offset: + * offer user offset adjustments in twoscompliment + * form with a scale factor of 15.6 mg/LSB (i.e. 0x7F = +2 g) + */ + + s8 x_axis_offset; + s8 y_axis_offset; + s8 z_axis_offset; + + /* + * TAP_X/Y/Z Enable: Setting TAP_X, Y, or Z Enable enables X, + * Y, or Z participation in Tap detection. A '0' excludes the + * selected axis from participation in Tap detection. + * Setting the SUPPRESS bit suppresses Double Tap detection if + * acceleration greater than tap_threshold is present between + * taps. + */ + +#define ADXL_SUPPRESS (1 << 3) +#define ADXL_TAP_X_EN (1 << 2) +#define ADXL_TAP_Y_EN (1 << 1) +#define ADXL_TAP_Z_EN (1 << 0) + + u8 tap_axis_control; + + /* + * tap_threshold: + * holds the threshold value for tap detection/interrupts. + * The data format is unsigned. The scale factor is 62.5 mg/LSB + * (i.e. 0xFF = +16 g). A zero value may result in undesirable + * behavior if Tap/Double Tap is enabled. + */ + + u8 tap_threshold; + + /* + * tap_duration: + * is an unsigned time value representing the maximum + * time that an event must be above the tap_threshold threshold + * to qualify as a tap event. The scale factor is 625 us/LSB. A zero + * value will prevent Tap/Double Tap functions from working. + */ + + u8 tap_duration; + + /* + * tap_latency: + * is an unsigned time value representing the wait time + * from the detection of a tap event to the opening of the time + * window tap_window for a possible second tap event. The scale + * factor is 1.25 ms/LSB. A zero value will disable the Double Tap + * function. + */ + + u8 tap_latency; + + /* + * tap_window: + * is an unsigned time value representing the amount + * of time after the expiration of tap_latency during which a second + * tap can begin. The scale factor is 1.25 ms/LSB. A zero value will + * disable the Double Tap function. + */ + + u8 tap_window; + + /* + * act_axis_control: + * X/Y/Z Enable: A '1' enables X, Y, or Z participation in activity + * or inactivity detection. A '0' excludes the selected axis from + * participation. If all of the axes are excluded, the function is + * disabled. + * AC/DC: A '0' = DC coupled operation and a '1' = AC coupled + * operation. In DC coupled operation, the current acceleration is + * compared with activity_threshold and inactivity_threshold directly + * to determine whether activity or inactivity is detected. In AC + * coupled operation for activity detection, the acceleration value + * at the start of activity detection is taken as a reference value. + * New samples of acceleration are then compared to this + * reference value and if the magnitude of the difference exceeds + * activity_threshold the device will trigger an activity interrupt. In + * AC coupled operation for inactivity detection, a reference value + * is used again for comparison and is updated whenever the + * device exceeds the inactivity threshold. Once the reference + * value is selected, the device compares the magnitude of the + * difference between the reference value and the current + * acceleration with inactivity_threshold. If the difference is below + * inactivity_threshold for a total of inactivity_time, the device is + * considered inactive and the inactivity interrupt is triggered. + */ + +#define ADXL_ACT_ACDC (1 << 7) +#define ADXL_ACT_X_EN (1 << 6) +#define ADXL_ACT_Y_EN (1 << 5) +#define ADXL_ACT_Z_EN (1 << 4) +#define ADXL_INACT_ACDC (1 << 3) +#define ADXL_INACT_X_EN (1 << 2) +#define ADXL_INACT_Y_EN (1 << 1) +#define ADXL_INACT_Z_EN (1 << 0) + + u8 act_axis_control; + + /* + * activity_threshold: + * holds the threshold value for activity detection. + * The data format is unsigned. The scale factor is + * 62.5 mg/LSB. A zero value may result in undesirable behavior if + * Activity interrupt is enabled. + */ + + u8 activity_threshold; + + /* + * inactivity_threshold: + * holds the threshold value for inactivity + * detection. The data format is unsigned. The scale + * factor is 62.5 mg/LSB. A zero value may result in undesirable + * behavior if Inactivity interrupt is enabled. + */ + + u8 inactivity_threshold; + + /* + * inactivity_time: + * is an unsigned time value representing the + * amount of time that acceleration must be below the value in + * inactivity_threshold for inactivity to be declared. The scale factor + * is 1 second/LSB. Unlike the other interrupt functions, which + * operate on unfiltered data, the inactivity function operates on the + * filtered output data. At least one output sample must be + * generated for the inactivity interrupt to be triggered. This will + * result in the function appearing un-responsive if the + * inactivity_time register is set with a value less than the time + * constant of the Output Data Rate. A zero value will result in an + * interrupt when the output data is below inactivity_threshold. + */ + + u8 inactivity_time; + + /* + * free_fall_threshold: + * holds the threshold value for Free-Fall detection. + * The data format is unsigned. The root-sum-square(RSS) value + * of all axes is calculated and compared to the value in + * free_fall_threshold to determine if a free fall event may be + * occurring. The scale factor is 62.5 mg/LSB. A zero value may + * result in undesirable behavior if Free-Fall interrupt is + * enabled. Values between 300 and 600 mg (0x05 to 0x09) are + * recommended. + */ + + u8 free_fall_threshold; + + /* + * free_fall_time: + * is an unsigned time value representing the minimum + * time that the RSS value of all axes must be less than + * free_fall_threshold to generate a Free-Fall interrupt. The + * scale factor is 5 ms/LSB. A zero value may result in + * undesirable behavior if Free-Fall interrupt is enabled. + * Values between 100 to 350 ms (0x14 to 0x46) are recommended. + */ + + u8 free_fall_time; + + /* + * data_rate: + * Selects device bandwidth and output data rate. + * RATE = 3200 Hz / (2^(15 - x)). Default value is 0x0A, or 100 Hz + * Output Data Rate. An Output Data Rate should be selected that + * is appropriate for the communication protocol and frequency + * selected. Selecting too high of an Output Data Rate with a low + * communication speed will result in samples being discarded. + */ + + u8 data_rate; + + /* + * data_range: + * FULL_RES: When this bit is set with the device is + * in Full-Resolution Mode, where the output resolution increases + * with RANGE to maintain a 4 mg/LSB scale factor. When this + * bit is cleared the device is in 10-bit Mode and RANGE determine the + * maximum g-Range and scale factor. + */ + +#define ADXL_FULL_RES (1 << 3) +#define ADXL_RANGE_PM_2g 0 +#define ADXL_RANGE_PM_4g 1 +#define ADXL_RANGE_PM_8g 2 +#define ADXL_RANGE_PM_16g 3 + + u8 data_range; + + /* + * low_power_mode: + * A '0' = Normal operation and a '1' = Reduced + * power operation with somewhat higher noise. + */ + + u8 low_power_mode; + + /* + * power_mode: + * LINK: A '1' with both the activity and inactivity functions + * enabled will delay the start of the activity function until + * inactivity is detected. Once activity is detected, inactivity + * detection will begin and prevent the detection of activity. This + * bit serially links the activity and inactivity functions. When '0' + * the inactivity and activity functions are concurrent. Additional + * information can be found in the Application section under Link + * Mode. + * AUTO_SLEEP: A '1' sets the ADXL34x to switch to Sleep Mode + * when inactivity (acceleration has been below inactivity_threshold + * for at least inactivity_time) is detected and the LINK bit is set. + * A '0' disables automatic switching to Sleep Mode. See SLEEP + * for further description. + */ + +#define ADXL_LINK (1 << 5) +#define ADXL_AUTO_SLEEP (1 << 4) + + u8 power_mode; + + /* + * fifo_mode: + * BYPASS The FIFO is bypassed + * FIFO FIFO collects up to 32 values then stops collecting data + * STREAM FIFO holds the last 32 data values. Once full, the FIFO's + * oldest data is lost as it is replaced with newer data + * + * DEFAULT should be ADXL_FIFO_STREAM + */ + +#define ADXL_FIFO_BYPASS 0 +#define ADXL_FIFO_FIFO 1 +#define ADXL_FIFO_STREAM 2 + + u8 fifo_mode; + + /* + * watermark: + * The Watermark feature can be used to reduce the interrupt load + * of the system. The FIFO fills up to the value stored in watermark + * [1..32] and then generates an interrupt. + * A '0' disables the watermark feature. + */ + + u8 watermark; + + u32 ev_type; /* EV_ABS or EV_REL */ + + u32 ev_code_x; /* ABS_X,Y,Z or REL_X,Y,Z */ + u32 ev_code_y; /* ABS_X,Y,Z or REL_X,Y,Z */ + u32 ev_code_z; /* ABS_X,Y,Z or REL_X,Y,Z */ + + /* + * A valid BTN or KEY Code; use tap_axis_control to disable + * event reporting + */ + + u32 ev_code_tap[3]; /* EV_KEY {X-Axis, Y-Axis, Z-Axis} */ + + /* + * A valid BTN or KEY Code for Free-Fall or Activity enables + * input event reporting. A '0' disables the Free-Fall or + * Activity reporting. + */ + + u32 ev_code_ff; /* EV_KEY */ + u32 ev_code_act_inactivity; /* EV_KEY */ + + /* + * Use ADXL34x INT2 instead of INT1 + */ + u8 use_int2; + + /* + * ADXL346 only ORIENTATION SENSING feature + * The orientation function of the ADXL346 reports both 2-D and + * 3-D orientation concurrently. + */ + +#define ADXL_EN_ORIENTATION_2D 1 +#define ADXL_EN_ORIENTATION_3D 2 +#define ADXL_EN_ORIENTATION_2D_3D 3 + + u8 orientation_enable; + + /* + * The width of the deadzone region between two or more + * orientation positions is determined by setting the Deadzone + * value. The deadzone region size can be specified with a + * resolution of 3.6deg. The deadzone angle represents the total + * angle where the orientation is considered invalid. + */ + +#define ADXL_DEADZONE_ANGLE_0p0 0 /* !!!0.0 [deg] */ +#define ADXL_DEADZONE_ANGLE_3p6 1 /* 3.6 [deg] */ +#define ADXL_DEADZONE_ANGLE_7p2 2 /* 7.2 [deg] */ +#define ADXL_DEADZONE_ANGLE_10p8 3 /* 10.8 [deg] */ +#define ADXL_DEADZONE_ANGLE_14p4 4 /* 14.4 [deg] */ +#define ADXL_DEADZONE_ANGLE_18p0 5 /* 18.0 [deg] */ +#define ADXL_DEADZONE_ANGLE_21p6 6 /* 21.6 [deg] */ +#define ADXL_DEADZONE_ANGLE_25p2 7 /* 25.2 [deg] */ + + u8 deadzone_angle; + + /* + * To eliminate most human motion such as walking or shaking, + * a Divisor value should be selected to effectively limit the + * orientation bandwidth. Set the depth of the filter used to + * low-pass filter the measured acceleration for stable + * orientation sensing + */ + +#define ADXL_LP_FILTER_DIVISOR_2 0 +#define ADXL_LP_FILTER_DIVISOR_4 1 +#define ADXL_LP_FILTER_DIVISOR_8 2 +#define ADXL_LP_FILTER_DIVISOR_16 3 +#define ADXL_LP_FILTER_DIVISOR_32 4 +#define ADXL_LP_FILTER_DIVISOR_64 5 +#define ADXL_LP_FILTER_DIVISOR_128 6 +#define ADXL_LP_FILTER_DIVISOR_256 7 + + u8 divisor_length; + + u32 ev_codes_orient_2d[4]; /* EV_KEY {+X, -X, +Y, -Y} */ + u32 ev_codes_orient_3d[6]; /* EV_KEY {+Z, +Y, +X, -X, -Y, -Z} */ +}; +#endif diff --git a/include/linux/input/cy8ctmg110_pdata.h b/include/linux/input/cy8ctmg110_pdata.h new file mode 100644 index 00000000000..09522cb5991 --- /dev/null +++ b/include/linux/input/cy8ctmg110_pdata.h @@ -0,0 +1,10 @@ +#ifndef _LINUX_CY8CTMG110_PDATA_H +#define _LINUX_CY8CTMG110_PDATA_H + +struct cy8ctmg110_pdata +{ + int reset_pin; /* Reset pin is wired to this GPIO (optional) */ + int irq_pin; /* IRQ pin is wired to this GPIO */ +}; + +#endif diff --git a/include/linux/input/matrix_keypad.h b/include/linux/input/matrix_keypad.h index c964cd7f436..80352ad6581 100644 --- a/include/linux/input/matrix_keypad.h +++ b/include/linux/input/matrix_keypad.h @@ -41,6 +41,9 @@ struct matrix_keymap_data { * @col_scan_delay_us: delay, measured in microseconds, that is * needed before we can keypad after activating column gpio * @debounce_ms: debounce interval in milliseconds + * @clustered_irq: may be specified if interrupts of all row/column GPIOs + * are bundled to one single irq + * @clustered_irq_flags: flags that are needed for the clustered irq * @active_low: gpio polarity * @wakeup: controls whether the device should be set up as wakeup * source @@ -63,6 +66,9 @@ struct matrix_keypad_platform_data { /* key debounce interval in milli-second */ unsigned int debounce_ms; + unsigned int clustered_irq; + unsigned int clustered_irq_flags; + bool active_low; bool wakeup; bool no_autorepeat; |