diff options
Diffstat (limited to 'include/linux/lis3lv02d.h')
| -rw-r--r-- | include/linux/lis3lv02d.h | 55 |
1 files changed, 54 insertions, 1 deletions
diff --git a/include/linux/lis3lv02d.h b/include/linux/lis3lv02d.h index 0e8a346424b..d4292c8431e 100644 --- a/include/linux/lis3lv02d.h +++ b/include/linux/lis3lv02d.h @@ -1,6 +1,52 @@ #ifndef __LIS3LV02D_H_ #define __LIS3LV02D_H_ +/** + * struct lis3lv02d_platform_data - lis3 chip family platform data + * @click_flags: Click detection unit configuration + * @click_thresh_x: Click detection unit x axis threshold + * @click_thresh_y: Click detection unit y axis threshold + * @click_thresh_z: Click detection unit z axis threshold + * @click_time_limit: Click detection unit time parameter + * @click_latency: Click detection unit latency parameter + * @click_window: Click detection unit window parameter + * @irq_cfg: On chip irq source and type configuration (click / + * data available / wake up, open drain, polarity) + * @irq_flags1: Additional irq triggering flags for irq channel 0 + * @irq_flags2: Additional irq triggering flags for irq channel 1 + * @duration1: Wake up unit 1 duration parameter + * @duration2: Wake up unit 2 duration parameter + * @wakeup_flags: Wake up unit 1 flags + * @wakeup_thresh: Wake up unit 1 threshold value + * @wakeup_flags2: Wake up unit 2 flags + * @wakeup_thresh2: Wake up unit 2 threshold value + * @hipass_ctrl: High pass filter control (enable / disable, cut off + * frequency) + * @axis_x: Sensor orientation remapping for x-axis + * @axis_y: Sensor orientation remapping for y-axis + * @axis_z: Sensor orientation remapping for z-axis + * @driver_features: Enable bits for different features. Disabled by default + * @default_rate: Default sampling rate. 0 means reset default + * @setup_resources: Interrupt line setup call back function + * @release_resources: Interrupt line release call back function + * @st_min_limits[3]: Selftest acceptance minimum values + * @st_max_limits[3]: Selftest acceptance maximum values + * @irq2: Irq line 2 number + * + * Platform data is used to setup the sensor chip. Meaning of the different + * chip features can be found from the data sheet. It is publicly available + * at www.st.com web pages. Currently the platform data is used + * only for the 8 bit device. The 8 bit device has two wake up / free fall + * detection units and click detection unit. There are plenty of ways to + * configure the chip which makes is quite hard to explain deeper meaning of + * the fields here. Behaviour of the detection blocks varies heavily depending + * on the configuration. For example, interrupt detection block can use high + * pass filtered data which makes it react to the changes in the acceleration. + * Irq_flags can be used to enable interrupt detection on the both edges. + * With proper chip configuration this produces interrupt when some trigger + * starts and when it goes away. + */ + struct lis3lv02d_platform_data { /* please note: the 'click' feature is only supported for * LIS[32]02DL variants of the chip and will be ignored for @@ -36,7 +82,10 @@ struct lis3lv02d_platform_data { #define LIS3_IRQ_OPEN_DRAIN (1 << 6) #define LIS3_IRQ_ACTIVE_LOW (1 << 7) unsigned char irq_cfg; - + unsigned char irq_flags1; /* Additional irq edge / level flags */ + unsigned char irq_flags2; /* Additional irq edge / level flags */ + unsigned char duration1; + unsigned char duration2; #define LIS3_WAKEUP_X_LO (1 << 0) #define LIS3_WAKEUP_X_HI (1 << 1) #define LIS3_WAKEUP_Y_LO (1 << 2) @@ -64,6 +113,10 @@ struct lis3lv02d_platform_data { s8 axis_x; s8 axis_y; s8 axis_z; +#define LIS3_USE_REGULATOR_CTRL 0x01 +#define LIS3_USE_BLOCK_READ 0x02 + u16 driver_features; + int default_rate; int (*setup_resources)(void); int (*release_resources)(void); /* Limits for selftest are specified in chip data sheet */ |