diff options
Diffstat (limited to 'include/linux/mfd/abx500/ab8500-bm.h')
| -rw-r--r-- | include/linux/mfd/abx500/ab8500-bm.h | 474 |
1 files changed, 474 insertions, 0 deletions
diff --git a/include/linux/mfd/abx500/ab8500-bm.h b/include/linux/mfd/abx500/ab8500-bm.h new file mode 100644 index 00000000000..44310c98ee6 --- /dev/null +++ b/include/linux/mfd/abx500/ab8500-bm.h @@ -0,0 +1,474 @@ +/* + * Copyright ST-Ericsson 2012. + * + * Author: Arun Murthy <arun.murthy@stericsson.com> + * Licensed under GPLv2. + */ + +#ifndef _AB8500_BM_H +#define _AB8500_BM_H + +#include <linux/kernel.h> +#include <linux/mfd/abx500.h> + +/* + * System control 2 register offsets. + * bank = 0x02 + */ +#define AB8500_MAIN_WDOG_CTRL_REG 0x01 +#define AB8500_LOW_BAT_REG 0x03 +#define AB8500_BATT_OK_REG 0x04 +/* + * USB/ULPI register offsets + * Bank : 0x5 + */ +#define AB8500_USB_LINE_STAT_REG 0x80 + +/* + * Charger / status register offfsets + * Bank : 0x0B + */ +#define AB8500_CH_STATUS1_REG 0x00 +#define AB8500_CH_STATUS2_REG 0x01 +#define AB8500_CH_USBCH_STAT1_REG 0x02 +#define AB8500_CH_USBCH_STAT2_REG 0x03 +#define AB8500_CH_FSM_STAT_REG 0x04 +#define AB8500_CH_STAT_REG 0x05 + +/* + * Charger / control register offfsets + * Bank : 0x0B + */ +#define AB8500_CH_VOLT_LVL_REG 0x40 +#define AB8500_CH_VOLT_LVL_MAX_REG 0x41 /*Only in Cut2.0*/ +#define AB8500_CH_OPT_CRNTLVL_REG 0x42 +#define AB8500_CH_OPT_CRNTLVL_MAX_REG 0x43 /*Only in Cut2.0*/ +#define AB8500_CH_WD_TIMER_REG 0x50 +#define AB8500_CHARG_WD_CTRL 0x51 +#define AB8500_BTEMP_HIGH_TH 0x52 +#define AB8500_LED_INDICATOR_PWM_CTRL 0x53 +#define AB8500_LED_INDICATOR_PWM_DUTY 0x54 +#define AB8500_BATT_OVV 0x55 +#define AB8500_CHARGER_CTRL 0x56 +#define AB8500_BAT_CTRL_CURRENT_SOURCE 0x60 /*Only in Cut2.0*/ + +/* + * Charger / main control register offsets + * Bank : 0x0B + */ +#define AB8500_MCH_CTRL1 0x80 +#define AB8500_MCH_CTRL2 0x81 +#define AB8500_MCH_IPT_CURLVL_REG 0x82 +#define AB8500_CH_WD_REG 0x83 + +/* + * Charger / USB control register offsets + * Bank : 0x0B + */ +#define AB8500_USBCH_CTRL1_REG 0xC0 +#define AB8500_USBCH_CTRL2_REG 0xC1 +#define AB8500_USBCH_IPT_CRNTLVL_REG 0xC2 + +/* + * Gas Gauge register offsets + * Bank : 0x0C + */ +#define AB8500_GASG_CC_CTRL_REG 0x00 +#define AB8500_GASG_CC_ACCU1_REG 0x01 +#define AB8500_GASG_CC_ACCU2_REG 0x02 +#define AB8500_GASG_CC_ACCU3_REG 0x03 +#define AB8500_GASG_CC_ACCU4_REG 0x04 +#define AB8500_GASG_CC_SMPL_CNTRL_REG 0x05 +#define AB8500_GASG_CC_SMPL_CNTRH_REG 0x06 +#define AB8500_GASG_CC_SMPL_CNVL_REG 0x07 +#define AB8500_GASG_CC_SMPL_CNVH_REG 0x08 +#define AB8500_GASG_CC_CNTR_AVGOFF_REG 0x09 +#define AB8500_GASG_CC_OFFSET_REG 0x0A +#define AB8500_GASG_CC_NCOV_ACCU 0x10 +#define AB8500_GASG_CC_NCOV_ACCU_CTRL 0x11 +#define AB8500_GASG_CC_NCOV_ACCU_LOW 0x12 +#define AB8500_GASG_CC_NCOV_ACCU_MED 0x13 +#define AB8500_GASG_CC_NCOV_ACCU_HIGH 0x14 + +/* + * Interrupt register offsets + * Bank : 0x0E + */ +#define AB8500_IT_SOURCE2_REG 0x01 +#define AB8500_IT_SOURCE21_REG 0x14 + +/* + * RTC register offsets + * Bank: 0x0F + */ +#define AB8500_RTC_BACKUP_CHG_REG 0x0C +#define AB8500_RTC_CC_CONF_REG 0x01 +#define AB8500_RTC_CTRL_REG 0x0B + +/* + * OTP register offsets + * Bank : 0x15 + */ +#define AB8500_OTP_CONF_15 0x0E + +/* GPADC constants from AB8500 spec, UM0836 */ +#define ADC_RESOLUTION 1024 +#define ADC_CH_MAIN_MIN 0 +#define ADC_CH_MAIN_MAX 20030 +#define ADC_CH_VBUS_MIN 0 +#define ADC_CH_VBUS_MAX 20030 +#define ADC_CH_VBAT_MIN 2300 +#define ADC_CH_VBAT_MAX 4800 +#define ADC_CH_BKBAT_MIN 0 +#define ADC_CH_BKBAT_MAX 3200 + +/* Main charge i/p current */ +#define MAIN_CH_IP_CUR_0P9A 0x80 +#define MAIN_CH_IP_CUR_1P0A 0x90 +#define MAIN_CH_IP_CUR_1P1A 0xA0 +#define MAIN_CH_IP_CUR_1P2A 0xB0 +#define MAIN_CH_IP_CUR_1P3A 0xC0 +#define MAIN_CH_IP_CUR_1P4A 0xD0 +#define MAIN_CH_IP_CUR_1P5A 0xE0 + +/* ChVoltLevel */ +#define CH_VOL_LVL_3P5 0x00 +#define CH_VOL_LVL_4P0 0x14 +#define CH_VOL_LVL_4P05 0x16 +#define CH_VOL_LVL_4P1 0x1B +#define CH_VOL_LVL_4P15 0x20 +#define CH_VOL_LVL_4P2 0x25 +#define CH_VOL_LVL_4P6 0x4D + +/* ChOutputCurrentLevel */ +#define CH_OP_CUR_LVL_0P1 0x00 +#define CH_OP_CUR_LVL_0P2 0x01 +#define CH_OP_CUR_LVL_0P3 0x02 +#define CH_OP_CUR_LVL_0P4 0x03 +#define CH_OP_CUR_LVL_0P5 0x04 +#define CH_OP_CUR_LVL_0P6 0x05 +#define CH_OP_CUR_LVL_0P7 0x06 +#define CH_OP_CUR_LVL_0P8 0x07 +#define CH_OP_CUR_LVL_0P9 0x08 +#define CH_OP_CUR_LVL_1P4 0x0D +#define CH_OP_CUR_LVL_1P5 0x0E +#define CH_OP_CUR_LVL_1P6 0x0F + +/* BTEMP High thermal limits */ +#define BTEMP_HIGH_TH_57_0 0x00 +#define BTEMP_HIGH_TH_52 0x01 +#define BTEMP_HIGH_TH_57_1 0x02 +#define BTEMP_HIGH_TH_62 0x03 + +/* current is mA */ +#define USB_0P1A 100 +#define USB_0P2A 200 +#define USB_0P3A 300 +#define USB_0P4A 400 +#define USB_0P5A 500 + +#define LOW_BAT_3P1V 0x20 +#define LOW_BAT_2P3V 0x00 +#define LOW_BAT_RESET 0x01 +#define LOW_BAT_ENABLE 0x01 + +/* Backup battery constants */ +#define BUP_ICH_SEL_50UA 0x00 +#define BUP_ICH_SEL_150UA 0x04 +#define BUP_ICH_SEL_300UA 0x08 +#define BUP_ICH_SEL_700UA 0x0C + +#define BUP_VCH_SEL_2P5V 0x00 +#define BUP_VCH_SEL_2P6V 0x01 +#define BUP_VCH_SEL_2P8V 0x02 +#define BUP_VCH_SEL_3P1V 0x03 + +/* Battery OVV constants */ +#define BATT_OVV_ENA 0x02 +#define BATT_OVV_TH_3P7 0x00 +#define BATT_OVV_TH_4P75 0x01 + +/* A value to indicate over voltage */ +#define BATT_OVV_VALUE 4750 + +/* VBUS OVV constants */ +#define VBUS_OVV_SELECT_MASK 0x78 +#define VBUS_OVV_SELECT_5P6V 0x00 +#define VBUS_OVV_SELECT_5P7V 0x08 +#define VBUS_OVV_SELECT_5P8V 0x10 +#define VBUS_OVV_SELECT_5P9V 0x18 +#define VBUS_OVV_SELECT_6P0V 0x20 +#define VBUS_OVV_SELECT_6P1V 0x28 +#define VBUS_OVV_SELECT_6P2V 0x30 +#define VBUS_OVV_SELECT_6P3V 0x38 + +#define VBUS_AUTO_IN_CURR_LIM_ENA 0x04 + +/* Fuel Gauge constants */ +#define RESET_ACCU 0x02 +#define READ_REQ 0x01 +#define CC_DEEP_SLEEP_ENA 0x02 +#define CC_PWR_UP_ENA 0x01 +#define CC_SAMPLES_40 0x28 +#define RD_NCONV_ACCU_REQ 0x01 +#define CC_CALIB 0x08 +#define CC_INTAVGOFFSET_ENA 0x10 +#define CC_MUXOFFSET 0x80 +#define CC_INT_CAL_N_AVG_MASK 0x60 +#define CC_INT_CAL_SAMPLES_16 0x40 +#define CC_INT_CAL_SAMPLES_8 0x20 +#define CC_INT_CAL_SAMPLES_4 0x00 + +/* RTC constants */ +#define RTC_BUP_CH_ENA 0x10 + +/* BatCtrl Current Source Constants */ +#define BAT_CTRL_7U_ENA 0x01 +#define BAT_CTRL_20U_ENA 0x02 +#define BAT_CTRL_CMP_ENA 0x04 +#define FORCE_BAT_CTRL_CMP_HIGH 0x08 +#define BAT_CTRL_PULL_UP_ENA 0x10 + +/* Battery type */ +#define BATTERY_UNKNOWN 00 + +/** + * struct res_to_temp - defines one point in a temp to res curve. To + * be used in battery packs that combines the identification resistor with a + * NTC resistor. + * @temp: battery pack temperature in Celcius + * @resist: NTC resistor net total resistance + */ +struct res_to_temp { + int temp; + int resist; +}; + +/** + * struct batres_vs_temp - defines one point in a temp vs battery internal + * resistance curve. + * @temp: battery pack temperature in Celcius + * @resist: battery internal reistance in mOhm + */ +struct batres_vs_temp { + int temp; + int resist; +}; + +/* Forward declaration */ +struct ab8500_fg; + +/** + * struct ab8500_fg_parameters - Fuel gauge algorithm parameters, in seconds + * if not specified + * @recovery_sleep_timer: Time between measurements while recovering + * @recovery_total_time: Total recovery time + * @init_timer: Measurement interval during startup + * @init_discard_time: Time we discard voltage measurement at startup + * @init_total_time: Total init time during startup + * @high_curr_time: Time current has to be high to go to recovery + * @accu_charging: FG accumulation time while charging + * @accu_high_curr: FG accumulation time in high current mode + * @high_curr_threshold: High current threshold, in mA + * @lowbat_threshold: Low battery threshold, in mV + * @battok_falling_th_sel0 Threshold in mV for battOk signal sel0 + * Resolution in 50 mV step. + * @battok_raising_th_sel1 Threshold in mV for battOk signal sel1 + * Resolution in 50 mV step. + * @user_cap_limit Capacity reported from user must be within this + * limit to be considered as sane, in percentage + * points. + * @maint_thres This is the threshold where we stop reporting + * battery full while in maintenance, in per cent + */ +struct ab8500_fg_parameters { + int recovery_sleep_timer; + int recovery_total_time; + int init_timer; + int init_discard_time; + int init_total_time; + int high_curr_time; + int accu_charging; + int accu_high_curr; + int high_curr_threshold; + int lowbat_threshold; + int battok_falling_th_sel0; + int battok_raising_th_sel1; + int user_cap_limit; + int maint_thres; +}; + +/** + * struct ab8500_charger_maximization - struct used by the board config. + * @use_maxi: Enable maximization for this battery type + * @maxi_chg_curr: Maximum charger current allowed + * @maxi_wait_cycles: cycles to wait before setting charger current + * @charger_curr_step delta between two charger current settings (mA) + */ +struct ab8500_maxim_parameters { + bool ena_maxi; + int chg_curr; + int wait_cycles; + int charger_curr_step; +}; + +/** + * struct ab8500_bm_capacity_levels - ab8500 capacity level data + * @critical: critical capacity level in percent + * @low: low capacity level in percent + * @normal: normal capacity level in percent + * @high: high capacity level in percent + * @full: full capacity level in percent + */ +struct ab8500_bm_capacity_levels { + int critical; + int low; + int normal; + int high; + int full; +}; + +/** + * struct ab8500_bm_charger_parameters - Charger specific parameters + * @usb_volt_max: maximum allowed USB charger voltage in mV + * @usb_curr_max: maximum allowed USB charger current in mA + * @ac_volt_max: maximum allowed AC charger voltage in mV + * @ac_curr_max: maximum allowed AC charger current in mA + */ +struct ab8500_bm_charger_parameters { + int usb_volt_max; + int usb_curr_max; + int ac_volt_max; + int ac_curr_max; +}; + +/** + * struct ab8500_bm_data - ab8500 battery management data + * @temp_under under this temp, charging is stopped + * @temp_low between this temp and temp_under charging is reduced + * @temp_high between this temp and temp_over charging is reduced + * @temp_over over this temp, charging is stopped + * @temp_interval_chg temperature measurement interval in s when charging + * @temp_interval_nochg temperature measurement interval in s when not charging + * @main_safety_tmr_h safety timer for main charger + * @usb_safety_tmr_h safety timer for usb charger + * @bkup_bat_v voltage which we charge the backup battery with + * @bkup_bat_i current which we charge the backup battery with + * @no_maintenance indicates that maintenance charging is disabled + * @adc_therm placement of thermistor, batctrl or battemp adc + * @chg_unknown_bat flag to enable charging of unknown batteries + * @enable_overshoot flag to enable VBAT overshoot control + * @fg_res resistance of FG resistor in 0.1mOhm + * @n_btypes number of elements in array bat_type + * @batt_id index of the identified battery in array bat_type + * @interval_charging charge alg cycle period time when charging (sec) + * @interval_not_charging charge alg cycle period time when not charging (sec) + * @temp_hysteresis temperature hysteresis + * @gnd_lift_resistance Battery ground to phone ground resistance (mOhm) + * @maxi: maximization parameters + * @cap_levels capacity in percent for the different capacity levels + * @bat_type table of supported battery types + * @chg_params charger parameters + * @fg_params fuel gauge parameters + */ +struct ab8500_bm_data { + int temp_under; + int temp_low; + int temp_high; + int temp_over; + int temp_interval_chg; + int temp_interval_nochg; + int main_safety_tmr_h; + int usb_safety_tmr_h; + int bkup_bat_v; + int bkup_bat_i; + bool no_maintenance; + bool chg_unknown_bat; + bool enable_overshoot; + enum abx500_adc_therm adc_therm; + int fg_res; + int n_btypes; + int batt_id; + int interval_charging; + int interval_not_charging; + int temp_hysteresis; + int gnd_lift_resistance; + const struct ab8500_maxim_parameters *maxi; + const struct ab8500_bm_capacity_levels *cap_levels; + const struct ab8500_bm_charger_parameters *chg_params; + const struct ab8500_fg_parameters *fg_params; +}; + +struct ab8500_charger_platform_data { + char **supplied_to; + size_t num_supplicants; + bool autopower_cfg; +}; + +struct ab8500_btemp_platform_data { + char **supplied_to; + size_t num_supplicants; +}; + +struct ab8500_fg_platform_data { + char **supplied_to; + size_t num_supplicants; +}; + +struct ab8500_chargalg_platform_data { + char **supplied_to; + size_t num_supplicants; +}; +struct ab8500_btemp; +struct ab8500_gpadc; +struct ab8500_fg; +#ifdef CONFIG_AB8500_BM +void ab8500_fg_reinit(void); +void ab8500_charger_usb_state_changed(u8 bm_usb_state, u16 mA); +struct ab8500_btemp *ab8500_btemp_get(void); +int ab8500_btemp_get_batctrl_temp(struct ab8500_btemp *btemp); +struct ab8500_fg *ab8500_fg_get(void); +int ab8500_fg_inst_curr_blocking(struct ab8500_fg *dev); +int ab8500_fg_inst_curr_start(struct ab8500_fg *di); +int ab8500_fg_inst_curr_finalize(struct ab8500_fg *di, int *res); +int ab8500_fg_inst_curr_done(struct ab8500_fg *di); + +#else +int ab8500_fg_inst_curr_done(struct ab8500_fg *di) +{ +} +static void ab8500_fg_reinit(void) +{ +} +static void ab8500_charger_usb_state_changed(u8 bm_usb_state, u16 mA) +{ +} +static struct ab8500_btemp *ab8500_btemp_get(void) +{ + return NULL; +} +static int ab8500_btemp_get_batctrl_temp(struct ab8500_btemp *btemp) +{ + return 0; +} +struct ab8500_fg *ab8500_fg_get(void) +{ + return NULL; +} +static int ab8500_fg_inst_curr_blocking(struct ab8500_fg *dev) +{ + return -ENODEV; +} + +static inline int ab8500_fg_inst_curr_start(struct ab8500_fg *di) +{ + return -ENODEV; +} + +static inline int ab8500_fg_inst_curr_finalize(struct ab8500_fg *di, int *res) +{ + return -ENODEV; +} + +#endif +#endif /* _AB8500_BM_H */ |