diff options
Diffstat (limited to 'include/linux/mmc/host.h')
| -rw-r--r-- | include/linux/mmc/host.h | 96 |
1 files changed, 51 insertions, 45 deletions
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h index a3ac9c48e5d..cbde4b7e675 100644 --- a/include/linux/mmc/host.h +++ b/include/linux/mmc/host.h @@ -12,6 +12,7 @@ #include <linux/leds.h> #include <linux/sched.h> +#include <linux/device.h> #include <linux/fault-inject.h> #include <linux/mmc/core.h> @@ -56,10 +57,13 @@ struct mmc_ios { #define MMC_TIMING_UHS_SDR50 3 #define MMC_TIMING_UHS_SDR104 4 #define MMC_TIMING_UHS_DDR50 5 +#define MMC_TIMING_MMC_HS200 6 #define MMC_SDR_MODE 0 #define MMC_1_2V_DDR_MODE 1 #define MMC_1_8V_DDR_MODE 2 +#define MMC_1_2V_SDR_MODE 3 +#define MMC_1_8V_SDR_MODE 4 unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */ @@ -77,34 +81,11 @@ struct mmc_ios { struct mmc_host_ops { /* - * Hosts that support power saving can use the 'enable' and 'disable' - * methods to exit and enter power saving states. 'enable' is called - * when the host is claimed and 'disable' is called (or scheduled with - * a delay) when the host is released. The 'disable' is scheduled if - * the disable delay set by 'mmc_set_disable_delay()' is non-zero, - * otherwise 'disable' is called immediately. 'disable' may be - * scheduled repeatedly, to permit ever greater power saving at the - * expense of ever greater latency to re-enable. Rescheduling is - * determined by the return value of the 'disable' method. A positive - * value gives the delay in milliseconds. - * - * In the case where a host function (like set_ios) may be called - * with or without the host claimed, enabling and disabling can be - * done directly and will nest correctly. Call 'mmc_host_enable()' and - * 'mmc_host_lazy_disable()' for this purpose, but note that these - * functions must be paired. - * - * Alternatively, 'mmc_host_enable()' may be paired with - * 'mmc_host_disable()' which calls 'disable' immediately. In this - * case the 'disable' method will be called with 'lazy' set to 0. - * This is mainly useful for error paths. - * - * Because lazy disable may be called from a work queue, the 'disable' - * method must claim the host when 'lazy' != 0, which will work - * correctly because recursion is detected and handled. + * 'enable' is called when the host is claimed and 'disable' is called + * when the host is released. 'enable' and 'disable' are deprecated. */ int (*enable)(struct mmc_host *host); - int (*disable)(struct mmc_host *host, int lazy); + int (*disable)(struct mmc_host *host); /* * It is optional for the host to implement pre_req and post_req in * order to support double buffering of requests (prepare one @@ -148,7 +129,9 @@ struct mmc_host_ops { void (*init_card)(struct mmc_host *host, struct mmc_card *card); int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios); - int (*execute_tuning)(struct mmc_host *host); + + /* The tuning command opcode value is different for SD and eMMC cards */ + int (*execute_tuning)(struct mmc_host *host, u32 opcode); void (*enable_preset_value)(struct mmc_host *host, bool enable); int (*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv); void (*hw_reset)(struct mmc_host *host); @@ -167,6 +150,11 @@ struct mmc_async_req { int (*err_check) (struct mmc_card *, struct mmc_async_req *); }; +struct mmc_hotplug { + unsigned int irq; + void *handler_priv; +}; + struct mmc_host { struct device *parent; struct device class_dev; @@ -208,7 +196,7 @@ struct mmc_host { #define MMC_CAP_SPI (1 << 4) /* Talks only SPI protocols */ #define MMC_CAP_NEEDS_POLL (1 << 5) /* Needs polling for card-detection */ #define MMC_CAP_8_BIT_DATA (1 << 6) /* Can the host do 8 bit transfers */ -#define MMC_CAP_DISABLE (1 << 7) /* Can the host be disabled */ + #define MMC_CAP_NONREMOVABLE (1 << 8) /* Nonremovable e.g. eMMC */ #define MMC_CAP_WAIT_WHILE_BUSY (1 << 9) /* Waits while card is busy */ #define MMC_CAP_ERASE (1 << 10) /* Allow erase/trim commands */ @@ -242,6 +230,14 @@ struct mmc_host { #define MMC_CAP2_CACHE_CTRL (1 << 1) /* Allow cache control */ #define MMC_CAP2_POWEROFF_NOTIFY (1 << 2) /* Notify poweroff supported */ #define MMC_CAP2_NO_MULTI_READ (1 << 3) /* Multiblock reads don't work */ +#define MMC_CAP2_NO_SLEEP_CMD (1 << 4) /* Don't allow sleep command */ +#define MMC_CAP2_HS200_1_8V_SDR (1 << 5) /* can support */ +#define MMC_CAP2_HS200_1_2V_SDR (1 << 6) /* can support */ +#define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \ + MMC_CAP2_HS200_1_2V_SDR) +#define MMC_CAP2_BROKEN_VOLTAGE (1 << 7) /* Use the broken voltage */ +#define MMC_CAP2_DETECT_ON_ERR (1 << 8) /* On I/O err check card removal */ +#define MMC_CAP2_HC_ERASE_SZ (1 << 9) /* High-capacity erase size */ mmc_pm_flag_t pm_caps; /* supported pm features */ unsigned int power_notify_type; @@ -253,10 +249,12 @@ struct mmc_host { int clk_requests; /* internal reference counter */ unsigned int clk_delay; /* number of MCI clk hold cycles */ bool clk_gated; /* clock gated */ - struct work_struct clk_gate_work; /* delayed clock gate */ + struct delayed_work clk_gate_work; /* delayed clock gate */ unsigned int clk_old; /* old clock value cache */ spinlock_t clk_lock; /* lock for clk fields */ struct mutex clk_gate_mutex; /* mutex for clock gating */ + struct device_attribute clkgate_delay_attr; + unsigned long clkgate_delay; #endif /* host specific block data */ @@ -282,13 +280,7 @@ struct mmc_host { unsigned int removed:1; /* host is being removed */ #endif - /* Only used with MMC_CAP_DISABLE */ - int enabled; /* host is enabled */ int rescan_disable; /* disable card detection */ - int nesting_cnt; /* "enable" nesting count */ - int en_dis_recurs; /* detect recursion */ - unsigned int disable_delay; /* disable delay in msecs */ - struct delayed_work disable; /* disabling work */ struct mmc_card *card; /* device attached to this host */ @@ -297,6 +289,8 @@ struct mmc_host { int claim_cnt; /* "claim" nesting count */ struct delayed_work detect; + int detect_change; /* card detect flag */ + struct mmc_hotplug hotplug; const struct mmc_bus_ops *bus_ops; /* current bus driver */ unsigned int bus_refs; /* reference counter */ @@ -323,6 +317,8 @@ struct mmc_host { struct fault_attr fail_mmc_request; #endif + unsigned int actual_clock; /* Actual HC clock rate */ + unsigned long private[0] ____cacheline_aligned; }; @@ -384,19 +380,10 @@ int mmc_card_awake(struct mmc_host *host); int mmc_card_sleep(struct mmc_host *host); int mmc_card_can_sleep(struct mmc_host *host); -int mmc_host_enable(struct mmc_host *host); -int mmc_host_disable(struct mmc_host *host); -int mmc_host_lazy_disable(struct mmc_host *host); int mmc_pm_notify(struct notifier_block *notify_block, unsigned long, void *); -static inline void mmc_set_disable_delay(struct mmc_host *host, - unsigned int disable_delay) -{ - host->disable_delay = disable_delay; -} - /* Module parameter */ -extern int mmc_assume_removable; +extern bool mmc_assume_removable; static inline int mmc_card_is_removable(struct mmc_host *host) { @@ -423,4 +410,23 @@ static inline int mmc_boot_partition_access(struct mmc_host *host) return !(host->caps2 & MMC_CAP2_BOOTPART_NOACC); } +#ifdef CONFIG_MMC_CLKGATE +void mmc_host_clk_hold(struct mmc_host *host); +void mmc_host_clk_release(struct mmc_host *host); +unsigned int mmc_host_clk_rate(struct mmc_host *host); + +#else +static inline void mmc_host_clk_hold(struct mmc_host *host) +{ +} + +static inline void mmc_host_clk_release(struct mmc_host *host) +{ +} + +static inline unsigned int mmc_host_clk_rate(struct mmc_host *host) +{ + return host->ios.clock; +} +#endif #endif /* LINUX_MMC_HOST_H */ |