diff options
Diffstat (limited to 'include/linux/mmc/sdio.h')
| -rw-r--r-- | include/linux/mmc/sdio.h | 92 |
1 files changed, 92 insertions, 0 deletions
diff --git a/include/linux/mmc/sdio.h b/include/linux/mmc/sdio.h index e5f06de7d52..56239f4aab0 100644 --- a/include/linux/mmc/sdio.h +++ b/include/linux/mmc/sdio.h @@ -49,5 +49,97 @@ #define R5_STATUS(x) (x & 0xCB00) #define R5_IO_CURRENT_STATE(x) ((x & 0x3000) >> 12) /* s, b */ +/* + * Card Common Control Registers (CCCR) + */ + +#define SDIO_CCCR_CCCR 0x00 + +#define SDIO_CCCR_REV_1_00 0 /* CCCR/FBR Version 1.00 */ +#define SDIO_CCCR_REV_1_10 1 /* CCCR/FBR Version 1.10 */ +#define SDIO_CCCR_REV_1_20 2 /* CCCR/FBR Version 1.20 */ + +#define SDIO_SDIO_REV_1_00 0 /* SDIO Spec Version 1.00 */ +#define SDIO_SDIO_REV_1_10 1 /* SDIO Spec Version 1.10 */ +#define SDIO_SDIO_REV_1_20 2 /* SDIO Spec Version 1.20 */ +#define SDIO_SDIO_REV_2_00 3 /* SDIO Spec Version 2.00 */ + +#define SDIO_CCCR_SD 0x01 + +#define SDIO_SD_REV_1_01 0 /* SD Physical Spec Version 1.01 */ +#define SDIO_SD_REV_1_10 1 /* SD Physical Spec Version 1.10 */ +#define SDIO_SD_REV_2_00 2 /* SD Physical Spec Version 2.00 */ + +#define SDIO_CCCR_IOEx 0x02 +#define SDIO_CCCR_IORx 0x03 + +#define SDIO_CCCR_IENx 0x04 /* Function/Master Interrupt Enable */ +#define SDIO_CCCR_INTx 0x05 /* Function Interrupt Pending */ + +#define SDIO_CCCR_ABORT 0x06 /* function abort/card reset */ + +#define SDIO_CCCR_IF 0x07 /* bus interface controls */ + +#define SDIO_BUS_WIDTH_1BIT 0x00 +#define SDIO_BUS_WIDTH_4BIT 0x02 + +#define SDIO_BUS_CD_DISABLE 0x80 /* disable pull-up on DAT3 (pin 1) */ + +#define SDIO_CCCR_CAPS 0x08 + +#define SDIO_CCCR_CAP_SDC 0x01 /* can do CMD52 while data transfer */ +#define SDIO_CCCR_CAP_SMB 0x02 /* can do multi-block xfers (CMD53) */ +#define SDIO_CCCR_CAP_SRW 0x04 /* supports read-wait protocol */ +#define SDIO_CCCR_CAP_SBS 0x08 /* supports suspend/resume */ +#define SDIO_CCCR_CAP_S4MI 0x10 /* interrupt during 4-bit CMD53 */ +#define SDIO_CCCR_CAP_E4MI 0x20 /* enable ints during 4-bit CMD53 */ +#define SDIO_CCCR_CAP_LSC 0x40 /* low speed card */ +#define SDIO_CCCR_CAP_4BLS 0x80 /* 4 bit low speed card */ + +#define SDIO_CCCR_CIS 0x09 /* common CIS pointer (3 bytes) */ + +/* Following 4 regs are valid only if SBS is set */ +#define SDIO_CCCR_SUSPEND 0x0c +#define SDIO_CCCR_SELx 0x0d +#define SDIO_CCCR_EXECx 0x0e +#define SDIO_CCCR_READYx 0x0f + +#define SDIO_CCCR_BLKSIZE 0x10 + +#define SDIO_CCCR_POWER 0x12 + +#define SDIO_POWER_SMPC 0x01 /* Supports Master Power Control */ +#define SDIO_POWER_EMPC 0x02 /* Enable Master Power Control */ + +#define SDIO_CCCR_SPEED 0x13 + +#define SDIO_SPEED_SHS 0x01 /* Supports High-Speed mode */ +#define SDIO_SPEED_EHS 0x02 /* Enable High-Speed mode */ + +/* + * Function Basic Registers (FBR) + */ + +#define SDIO_FBR_STD_IF 0x00 + +#define SDIO_FBR_SUPPORTS_CSA 0x40 /* supports Code Storage Area */ +#define SDIO_FBR_ENABLE_CSA 0x80 /* enable Code Storage Area */ + +#define SDIO_FBR_STD_IF_EXT 0x01 + +#define SDIO_FBR_POWER 0x02 + +#define SDIO_FBR_POWER_SPS 0x01 /* Supports Power Selection */ +#define SDIO_FBR_POWER_EPS 0x02 /* Enable (low) Power Selection */ + +#define SDIO_FBR_CIS 0x09 /* CIS pointer (3 bytes) */ + + +#define SDIO_FBR_CSA 0x0C /* CSA pointer (3 bytes) */ + +#define SDIO_FBR_CSA_DATA 0x0F + +#define SDIO_FBR_BLKSIZE 0x10 /* block size (2 bytes) */ + #endif |