diff options
Diffstat (limited to 'include/linux/nl80211.h')
| -rw-r--r-- | include/linux/nl80211.h | 371 |
1 files changed, 365 insertions, 6 deletions
diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h index bbfa1093f60..c7ccaae15af 100644 --- a/include/linux/nl80211.h +++ b/include/linux/nl80211.h @@ -77,6 +77,39 @@ */ /** + * DOC: Virtual interface / concurrency capabilities + * + * Some devices are able to operate with virtual MACs, they can have + * more than one virtual interface. The capability handling for this + * is a bit complex though, as there may be a number of restrictions + * on the types of concurrency that are supported. + * + * To start with, each device supports the interface types listed in + * the %NL80211_ATTR_SUPPORTED_IFTYPES attribute, but by listing the + * types there no concurrency is implied. + * + * Once concurrency is desired, more attributes must be observed: + * To start with, since some interface types are purely managed in + * software, like the AP-VLAN type in mac80211 for example, there's + * an additional list of these, they can be added at any time and + * are only restricted by some semantic restrictions (e.g. AP-VLAN + * cannot be added without a corresponding AP interface). This list + * is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute. + * + * Further, the list of supported combinations is exported. This is + * in the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute. Basically, + * it exports a list of "groups", and at any point in time the + * interfaces that are currently active must fall into any one of + * the advertised groups. Within each group, there are restrictions + * on the number of interfaces of different types that are supported + * and also the number of different channels, along with potentially + * some other restrictions. See &enum nl80211_if_combination_attrs. + * + * All together, these attributes define the concurrency of virtual + * interfaces that a given device supports. + */ + +/** * enum nl80211_commands - supported nl80211 commands * * @NL80211_CMD_UNSPEC: unspecified command to catch errors @@ -203,6 +236,28 @@ * @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons, * partial scan results may be available * + * @NL80211_CMD_START_SCHED_SCAN: start a scheduled scan at certain + * intervals, as specified by %NL80211_ATTR_SCHED_SCAN_INTERVAL. + * Like with normal scans, if SSIDs (%NL80211_ATTR_SCAN_SSIDS) + * are passed, they are used in the probe requests. For + * broadcast, a broadcast SSID must be passed (ie. an empty + * string). If no SSID is passed, no probe requests are sent and + * a passive scan is performed. %NL80211_ATTR_SCAN_FREQUENCIES, + * if passed, define which channels should be scanned; if not + * passed, all channels allowed for the current regulatory domain + * are used. Extra IEs can also be passed from the userspace by + * using the %NL80211_ATTR_IE attribute. + * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan + * @NL80211_CMD_SCHED_SCAN_RESULTS: indicates that there are scheduled scan + * results available. + * @NL80211_CMD_SCHED_SCAN_STOPPED: indicates that the scheduled scan has + * stopped. The driver may issue this event at any time during a + * scheduled scan. One reason for stopping the scan is if the hardware + * does not support starting an association or a normal scan while running + * a scheduled scan. This event is also sent when the + * %NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface + * is brought down while a scheduled scan was running. + * * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation * or noise level * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to @@ -410,6 +465,24 @@ * notification. This event is used to indicate that an unprotected * disassociation frame was dropped when MFP is in use. * + * @NL80211_CMD_NEW_PEER_CANDIDATE: Notification on the reception of a + * beacon or probe response from a compatible mesh peer. This is only + * sent while no station information (sta_info) exists for the new peer + * candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH is set. On + * reception of this notification, userspace may decide to create a new + * station (@NL80211_CMD_NEW_STATION). To stop this notification from + * reoccurring, the userspace authentication daemon may want to create the + * new station with the AUTHENTICATED flag unset and maybe change it later + * depending on the authentication result. + * + * @NL80211_CMD_GET_WOWLAN: get Wake-on-Wireless-LAN (WoWLAN) settings. + * @NL80211_CMD_SET_WOWLAN: set Wake-on-Wireless-LAN (WoWLAN) settings. + * Since wireless is more complex than wired ethernet, it supports + * various triggers. These triggers can be configured through this + * command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For + * more background information, see + * http://wireless.kernel.org/en/users/Documentation/WoWLAN. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -522,6 +595,16 @@ enum nl80211_commands { NL80211_CMD_UNPROT_DEAUTHENTICATE, NL80211_CMD_UNPROT_DISASSOCIATE, + NL80211_CMD_NEW_PEER_CANDIDATE, + + NL80211_CMD_GET_WOWLAN, + NL80211_CMD_SET_WOWLAN, + + NL80211_CMD_START_SCHED_SCAN, + NL80211_CMD_STOP_SCHED_SCAN, + NL80211_CMD_SCHED_SCAN_RESULTS, + NL80211_CMD_SCHED_SCAN_STOPPED, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -545,6 +628,7 @@ enum nl80211_commands { /* source-level API compatibility */ #define NL80211_CMD_GET_MESH_PARAMS NL80211_CMD_GET_MESH_CONFIG #define NL80211_CMD_SET_MESH_PARAMS NL80211_CMD_SET_MESH_CONFIG +#define NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE NL80211_MESH_SETUP_IE /** * enum nl80211_attrs - nl80211 netlink attributes @@ -886,6 +970,31 @@ enum nl80211_commands { * changed once the mesh is active. * @NL80211_ATTR_MESH_CONFIG: Mesh configuration parameters, a nested attribute * containing attributes from &enum nl80211_meshconf_params. + * @NL80211_ATTR_SUPPORT_MESH_AUTH: Currently, this means the underlying driver + * allows auth frames in a mesh to be passed to userspace for processing via + * the @NL80211_MESH_SETUP_USERSPACE_AUTH flag. + * @NL80211_ATTR_STA_PLINK_STATE: The state of a mesh peer link as + * defined in &enum nl80211_plink_state. Used when userspace is + * driving the peer link management state machine. + * @NL80211_MESH_SETUP_USERSPACE_AMPE must be enabled. + * + * @NL80211_ATTR_WOWLAN_SUPPORTED: indicates, as part of the wiphy capabilities, + * the supported WoWLAN triggers + * @NL80211_ATTR_WOWLAN_TRIGGERS: used by %NL80211_CMD_SET_WOWLAN to + * indicate which WoW triggers should be enabled. This is also + * used by %NL80211_CMD_GET_WOWLAN to get the currently enabled WoWLAN + * triggers. + + * @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan + * cycles, in msecs. + * + * @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported + * interface combinations. In each nested item, it contains attributes + * defined in &enum nl80211_if_combination_attrs. + * @NL80211_ATTR_SOFTWARE_IFTYPES: Nested attribute (just like + * %NL80211_ATTR_SUPPORTED_IFTYPES) containing the interface types that + * are managed in software: interfaces of these types aren't subject to + * any restrictions in their number or combinations. * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use @@ -1074,6 +1183,17 @@ enum nl80211_attrs { NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX, NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX, + NL80211_ATTR_SUPPORT_MESH_AUTH, + NL80211_ATTR_STA_PLINK_STATE, + + NL80211_ATTR_WOWLAN_TRIGGERS, + NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, + + NL80211_ATTR_SCHED_SCAN_INTERVAL, + + NL80211_ATTR_INTERFACE_COMBINATIONS, + NL80211_ATTR_SOFTWARE_IFTYPES, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -1126,7 +1246,9 @@ enum nl80211_attrs { * @NL80211_IFTYPE_ADHOC: independent BSS member * @NL80211_IFTYPE_STATION: managed BSS member * @NL80211_IFTYPE_AP: access point - * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points + * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points; VLAN interfaces + * are a bit special in that they must always be tied to a pre-existing + * AP type interface. * @NL80211_IFTYPE_WDS: wireless distribution interface * @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames * @NL80211_IFTYPE_MESH_POINT: mesh point @@ -1168,6 +1290,7 @@ enum nl80211_iftype { * with short barker preamble * @NL80211_STA_FLAG_WME: station is WME/QoS capable * @NL80211_STA_FLAG_MFP: station uses management frame protection + * @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated * @NL80211_STA_FLAG_MAX: highest station flag number currently defined * @__NL80211_STA_FLAG_AFTER_LAST: internal use */ @@ -1177,6 +1300,7 @@ enum nl80211_sta_flags { NL80211_STA_FLAG_SHORT_PREAMBLE, NL80211_STA_FLAG_WME, NL80211_STA_FLAG_MFP, + NL80211_STA_FLAG_AUTHENTICATED, /* keep last */ __NL80211_STA_FLAG_AFTER_LAST, @@ -1222,6 +1346,36 @@ enum nl80211_rate_info { }; /** + * enum nl80211_sta_bss_param - BSS information collected by STA + * + * These attribute types are used with %NL80211_STA_INFO_BSS_PARAM + * when getting information about the bitrate of a station. + * + * @__NL80211_STA_BSS_PARAM_INVALID: attribute number 0 is reserved + * @NL80211_STA_BSS_PARAM_CTS_PROT: whether CTS protection is enabled (flag) + * @NL80211_STA_BSS_PARAM_SHORT_PREAMBLE: whether short preamble is enabled + * (flag) + * @NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME: whether short slot time is enabled + * (flag) + * @NL80211_STA_BSS_PARAM_DTIM_PERIOD: DTIM period for beaconing (u8) + * @NL80211_STA_BSS_PARAM_BEACON_INTERVAL: Beacon interval (u16) + * @NL80211_STA_BSS_PARAM_MAX: highest sta_bss_param number currently defined + * @__NL80211_STA_BSS_PARAM_AFTER_LAST: internal use + */ +enum nl80211_sta_bss_param { + __NL80211_STA_BSS_PARAM_INVALID, + NL80211_STA_BSS_PARAM_CTS_PROT, + NL80211_STA_BSS_PARAM_SHORT_PREAMBLE, + NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME, + NL80211_STA_BSS_PARAM_DTIM_PERIOD, + NL80211_STA_BSS_PARAM_BEACON_INTERVAL, + + /* keep last */ + __NL80211_STA_BSS_PARAM_AFTER_LAST, + NL80211_STA_BSS_PARAM_MAX = __NL80211_STA_BSS_PARAM_AFTER_LAST - 1 +}; + +/** * enum nl80211_sta_info - station information * * These attribute types are used with %NL80211_ATTR_STA_INFO @@ -1233,7 +1387,7 @@ enum nl80211_rate_info { * @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (u32, to this station) * @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm) * @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute - * containing info as possible, see &enum nl80211_sta_info_txrate. + * containing info as possible, see &enum nl80211_rate_info * @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station) * @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (u32, to this * station) @@ -1243,8 +1397,12 @@ enum nl80211_rate_info { * @NL80211_STA_INFO_LLID: the station's mesh LLID * @NL80211_STA_INFO_PLID: the station's mesh PLID * @NL80211_STA_INFO_PLINK_STATE: peer link state for the station + * (see %enum nl80211_plink_state) * @NL80211_STA_INFO_RX_BITRATE: last unicast data frame rx rate, nested * attribute, like NL80211_STA_INFO_TX_BITRATE. + * @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute + * containing info as possible, see &enum nl80211_sta_bss_param + * @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected * @__NL80211_STA_INFO_AFTER_LAST: internal * @NL80211_STA_INFO_MAX: highest possible station info attribute */ @@ -1264,6 +1422,8 @@ enum nl80211_sta_info { NL80211_STA_INFO_TX_FAILED, NL80211_STA_INFO_SIGNAL_AVG, NL80211_STA_INFO_RX_BITRATE, + NL80211_STA_INFO_BSS_PARAM, + NL80211_STA_INFO_CONNECTED_TIME, /* keep last */ __NL80211_STA_INFO_AFTER_LAST, @@ -1686,9 +1846,21 @@ enum nl80211_meshconf_params { * vendor specific path metric or disable it to use the default Airtime * metric. * - * @NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE: A vendor specific information - * element that vendors will use to identify the path selection methods and - * metrics in use. + * @NL80211_MESH_SETUP_IE: Information elements for this mesh, for instance, a + * robust security network ie, or a vendor specific information element that + * vendors will use to identify the path selection methods and metrics in use. + * + * @NL80211_MESH_SETUP_USERSPACE_AUTH: Enable this option if an authentication + * daemon will be authenticating mesh candidates. + * + * @NL80211_MESH_SETUP_USERSPACE_AMPE: Enable this option if an authentication + * daemon will be securing peer link frames. AMPE is a secured version of Mesh + * Peering Management (MPM) and is implemented with the assistance of a + * userspace daemon. When this flag is set, the kernel will send peer + * management frames to a userspace daemon that will implement AMPE + * functionality (security capabilities selection, key confirmation, and key + * management). When the flag is unset (default), the kernel can autonomously + * complete (unsecured) mesh peering without the need of a userspace daemon. * * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use @@ -1697,7 +1869,9 @@ enum nl80211_mesh_setup_params { __NL80211_MESH_SETUP_INVALID, NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL, NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC, - NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE, + NL80211_MESH_SETUP_IE, + NL80211_MESH_SETUP_USERSPACE_AUTH, + NL80211_MESH_SETUP_USERSPACE_AMPE, /* keep last */ __NL80211_MESH_SETUP_ATTR_AFTER_LAST, @@ -2002,4 +2176,189 @@ enum nl80211_tx_power_setting { NL80211_TX_POWER_FIXED, }; +/** + * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute + * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute + * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has + * a zero bit are ignored + * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have + * a bit for each byte in the pattern. The lowest-order bit corresponds + * to the first byte of the pattern, but the bytes of the pattern are + * in a little-endian-like format, i.e. the 9th byte of the pattern + * corresponds to the lowest-order bit in the second byte of the mask. + * For example: The match 00:xx:00:00:xx:00:00:00:00:xx:xx:xx (where + * xx indicates "don't care") would be represented by a pattern of + * twelve zero bytes, and a mask of "0xed,0x07". + * Note that the pattern matching is done as though frames were not + * 802.11 frames but 802.3 frames, i.e. the frame is fully unpacked + * first (including SNAP header unpacking) and then matched. + * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes + * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number + */ +enum nl80211_wowlan_packet_pattern_attr { + __NL80211_WOWLAN_PKTPAT_INVALID, + NL80211_WOWLAN_PKTPAT_MASK, + NL80211_WOWLAN_PKTPAT_PATTERN, + + NUM_NL80211_WOWLAN_PKTPAT, + MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1, +}; + +/** + * struct nl80211_wowlan_pattern_support - pattern support information + * @max_patterns: maximum number of patterns supported + * @min_pattern_len: minimum length of each pattern + * @max_pattern_len: maximum length of each pattern + * + * This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when + * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the + * capability information given by the kernel to userspace. + */ +struct nl80211_wowlan_pattern_support { + __u32 max_patterns; + __u32 min_pattern_len; + __u32 max_pattern_len; +} __attribute__((packed)); + +/** + * enum nl80211_wowlan_triggers - WoWLAN trigger definitions + * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes + * @NL80211_WOWLAN_TRIG_ANY: wake up on any activity, do not really put + * the chip into a special state -- works best with chips that have + * support for low-power operation already (flag) + * @NL80211_WOWLAN_TRIG_DISCONNECT: wake up on disconnect, the way disconnect + * is detected is implementation-specific (flag) + * @NL80211_WOWLAN_TRIG_MAGIC_PKT: wake up on magic packet (6x 0xff, followed + * by 16 repetitions of MAC addr, anywhere in payload) (flag) + * @NL80211_WOWLAN_TRIG_PKT_PATTERN: wake up on the specified packet patterns + * which are passed in an array of nested attributes, each nested attribute + * defining a with attributes from &struct nl80211_wowlan_trig_pkt_pattern. + * Each pattern defines a wakeup packet. The matching is done on the MSDU, + * i.e. as though the packet was an 802.3 packet, so the pattern matching + * is done after the packet is converted to the MSDU. + * + * In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute + * carrying a &struct nl80211_wowlan_pattern_support. + * @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers + * @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number + */ +enum nl80211_wowlan_triggers { + __NL80211_WOWLAN_TRIG_INVALID, + NL80211_WOWLAN_TRIG_ANY, + NL80211_WOWLAN_TRIG_DISCONNECT, + NL80211_WOWLAN_TRIG_MAGIC_PKT, + NL80211_WOWLAN_TRIG_PKT_PATTERN, + + /* keep last */ + NUM_NL80211_WOWLAN_TRIG, + MAX_NL80211_WOWLAN_TRIG = NUM_NL80211_WOWLAN_TRIG - 1 +}; + +/** + * enum nl80211_iface_limit_attrs - limit attributes + * @NL80211_IFACE_LIMIT_UNSPEC: (reserved) + * @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that + * can be chosen from this set of interface types (u32) + * @NL80211_IFACE_LIMIT_TYPES: nested attribute containing a + * flag attribute for each interface type in this set + * @NUM_NL80211_IFACE_LIMIT: number of attributes + * @MAX_NL80211_IFACE_LIMIT: highest attribute number + */ +enum nl80211_iface_limit_attrs { + NL80211_IFACE_LIMIT_UNSPEC, + NL80211_IFACE_LIMIT_MAX, + NL80211_IFACE_LIMIT_TYPES, + + /* keep last */ + NUM_NL80211_IFACE_LIMIT, + MAX_NL80211_IFACE_LIMIT = NUM_NL80211_IFACE_LIMIT - 1 +}; + +/** + * enum nl80211_if_combination_attrs -- interface combination attributes + * + * @NL80211_IFACE_COMB_UNSPEC: (reserved) + * @NL80211_IFACE_COMB_LIMITS: Nested attributes containing the limits + * for given interface types, see &enum nl80211_iface_limit_attrs. + * @NL80211_IFACE_COMB_MAXNUM: u32 attribute giving the total number of + * interfaces that can be created in this group. This number doesn't + * apply to interfaces purely managed in software, which are listed + * in a separate attribute %NL80211_ATTR_INTERFACES_SOFTWARE. + * @NL80211_IFACE_COMB_STA_AP_BI_MATCH: flag attribute specifying that + * beacon intervals within this group must be all the same even for + * infrastructure and AP/GO combinations, i.e. the GO(s) must adopt + * the infrastructure network's beacon interval. + * @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many + * different channels may be used within this group. + * @NUM_NL80211_IFACE_COMB: number of attributes + * @MAX_NL80211_IFACE_COMB: highest attribute number + * + * Examples: + * limits = [ #{STA} <= 1, #{AP} <= 1 ], matching BI, channels = 1, max = 2 + * => allows an AP and a STA that must match BIs + * + * numbers = [ #{AP, P2P-GO} <= 8 ], channels = 1, max = 8 + * => allows 8 of AP/GO + * + * numbers = [ #{STA} <= 2 ], channels = 2, max = 2 + * => allows two STAs on different channels + * + * numbers = [ #{STA} <= 1, #{P2P-client,P2P-GO} <= 3 ], max = 4 + * => allows a STA plus three P2P interfaces + * + * The list of these four possiblities could completely be contained + * within the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute to indicate + * that any of these groups must match. + * + * "Combinations" of just a single interface will not be listed here, + * a single interface of any valid interface type is assumed to always + * be possible by itself. This means that implicitly, for each valid + * interface type, the following group always exists: + * numbers = [ #{<type>} <= 1 ], channels = 1, max = 1 + */ +enum nl80211_if_combination_attrs { + NL80211_IFACE_COMB_UNSPEC, + NL80211_IFACE_COMB_LIMITS, + NL80211_IFACE_COMB_MAXNUM, + NL80211_IFACE_COMB_STA_AP_BI_MATCH, + NL80211_IFACE_COMB_NUM_CHANNELS, + + /* keep last */ + NUM_NL80211_IFACE_COMB, + MAX_NL80211_IFACE_COMB = NUM_NL80211_IFACE_COMB - 1 +}; + + +/** + * enum nl80211_plink_state - state of a mesh peer link finite state machine + * + * @NL80211_PLINK_LISTEN: initial state, considered the implicit + * state of non existant mesh peer links + * @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to + * this mesh peer + * @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received + * from this mesh peer + * @NL80211_PLINK_CNF_RCVD: mesh plink confirm frame has been + * received from this mesh peer + * @NL80211_PLINK_ESTAB: mesh peer link is established + * @NL80211_PLINK_HOLDING: mesh peer link is being closed or cancelled + * @NL80211_PLINK_BLOCKED: all frames transmitted from this mesh + * plink are discarded + * @NUM_NL80211_PLINK_STATES: number of peer link states + * @MAX_NL80211_PLINK_STATES: highest numerical value of plink states + */ +enum nl80211_plink_state { + NL80211_PLINK_LISTEN, + NL80211_PLINK_OPN_SNT, + NL80211_PLINK_OPN_RCVD, + NL80211_PLINK_CNF_RCVD, + NL80211_PLINK_ESTAB, + NL80211_PLINK_HOLDING, + NL80211_PLINK_BLOCKED, + + /* keep last */ + NUM_NL80211_PLINK_STATES, + MAX_NL80211_PLINK_STATES = NUM_NL80211_PLINK_STATES - 1 +}; + #endif /* __LINUX_NL80211_H */ |