diff options
Diffstat (limited to 'include/linux/nl80211.h')
| -rw-r--r-- | include/linux/nl80211.h | 152 |
1 files changed, 150 insertions, 2 deletions
diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h index 9bad65400fb..e08c8bcfb78 100644 --- a/include/linux/nl80211.h +++ b/include/linux/nl80211.h @@ -25,8 +25,9 @@ * * @NL80211_CMD_GET_WIPHY: request information about a wiphy or dump request * to get a list of all present wiphys. - * @NL80211_CMD_SET_WIPHY: set wiphy name, needs %NL80211_ATTR_WIPHY and - * %NL80211_ATTR_WIPHY_NAME. + * @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or + * %NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME + * and/or %NL80211_ATTR_WIPHY_TXQ_PARAMS. * @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request * or rename notification. Has attributes %NL80211_ATTR_WIPHY and * %NL80211_ATTR_WIPHY_NAME. @@ -106,6 +107,12 @@ * to the the specified ISO/IEC 3166-1 alpha2 country code. The core will * store this as a valid request and then query userspace for it. * + * @NL80211_CMD_GET_MESH_PARAMS: Get mesh networking properties for the + * interface identified by %NL80211_ATTR_IFINDEX + * + * @NL80211_CMD_SET_MESH_PARAMS: Set mesh networking properties for the + * interface identified by %NL80211_ATTR_IFINDEX + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -148,6 +155,9 @@ enum nl80211_commands { NL80211_CMD_SET_REG, NL80211_CMD_REQ_SET_REG, + NL80211_CMD_GET_MESH_PARAMS, + NL80211_CMD_SET_MESH_PARAMS, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -169,6 +179,7 @@ enum nl80211_commands { * @NL80211_ATTR_WIPHY: index of wiphy to operate on, cf. * /sys/class/ieee80211/<phyname>/index * @NL80211_ATTR_WIPHY_NAME: wiphy name (used for renaming) + * @NL80211_ATTR_WIPHY_TXQ_PARAMS: a nested array of TX queue parameters * * @NL80211_ATTR_IFINDEX: network interface index of the device to operate on * @NL80211_ATTR_IFNAME: network interface name @@ -234,6 +245,9 @@ enum nl80211_commands { * (u8, 0 or 1) * @NL80211_ATTR_BSS_SHORT_SLOT_TIME: whether short slot time enabled * (u8, 0 or 1) + * @NL80211_ATTR_BSS_BASIC_RATES: basic rates, array of basic + * rates in format defined by IEEE 802.11 7.3.2.2 but without the length + * restriction (at most %NL80211_MAX_SUPP_RATES). * * @NL80211_ATTR_HT_CAPABILITY: HT Capability information element (from * association request when used with NL80211_CMD_NEW_STATION) @@ -296,6 +310,12 @@ enum nl80211_attrs { NL80211_ATTR_REG_ALPHA2, NL80211_ATTR_REG_RULES, + NL80211_ATTR_MESH_PARAMS, + + NL80211_ATTR_BSS_BASIC_RATES, + + NL80211_ATTR_WIPHY_TXQ_PARAMS, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -307,6 +327,8 @@ enum nl80211_attrs { * here */ #define NL80211_ATTR_HT_CAPABILITY NL80211_ATTR_HT_CAPABILITY +#define NL80211_ATTR_BSS_BASIC_RATES NL80211_ATTR_BSS_BASIC_RATES +#define NL80211_ATTR_WIPHY_TXQ_PARAMS NL80211_ATTR_WIPHY_TXQ_PARAMS #define NL80211_MAX_SUPP_RATES 32 #define NL80211_MAX_SUPP_REG_RULES 32 @@ -452,17 +474,29 @@ enum nl80211_mpath_info { * an array of nested frequency attributes * @NL80211_BAND_ATTR_RATES: supported bitrates in this band, * an array of nested bitrate attributes + * @NL80211_BAND_ATTR_HT_MCS_SET: 16-byte attribute containing the MCS set as + * defined in 802.11n + * @NL80211_BAND_ATTR_HT_CAPA: HT capabilities, as in the HT information IE + * @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n + * @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n */ enum nl80211_band_attr { __NL80211_BAND_ATTR_INVALID, NL80211_BAND_ATTR_FREQS, NL80211_BAND_ATTR_RATES, + NL80211_BAND_ATTR_HT_MCS_SET, + NL80211_BAND_ATTR_HT_CAPA, + NL80211_BAND_ATTR_HT_AMPDU_FACTOR, + NL80211_BAND_ATTR_HT_AMPDU_DENSITY, + /* keep last */ __NL80211_BAND_ATTR_AFTER_LAST, NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1 }; +#define NL80211_BAND_ATTR_HT_CAPA NL80211_BAND_ATTR_HT_CAPA + /** * enum nl80211_frequency_attr - frequency attributes * @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz @@ -474,6 +508,8 @@ enum nl80211_band_attr { * on this channel in current regulatory domain. * @NL80211_FREQUENCY_ATTR_RADAR: Radar detection is mandatory * on this channel in current regulatory domain. + * @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm + * (100 * dBm). */ enum nl80211_frequency_attr { __NL80211_FREQUENCY_ATTR_INVALID, @@ -482,12 +518,15 @@ enum nl80211_frequency_attr { NL80211_FREQUENCY_ATTR_PASSIVE_SCAN, NL80211_FREQUENCY_ATTR_NO_IBSS, NL80211_FREQUENCY_ATTR_RADAR, + NL80211_FREQUENCY_ATTR_MAX_TX_POWER, /* keep last */ __NL80211_FREQUENCY_ATTR_AFTER_LAST, NL80211_FREQUENCY_ATTR_MAX = __NL80211_FREQUENCY_ATTR_AFTER_LAST - 1 }; +#define NL80211_FREQUENCY_ATTR_MAX_TX_POWER NL80211_FREQUENCY_ATTR_MAX_TX_POWER + /** * enum nl80211_bitrate_attr - bitrate attributes * @NL80211_BITRATE_ATTR_RATE: Bitrate in units of 100 kbps @@ -594,4 +633,113 @@ enum nl80211_mntr_flags { NL80211_MNTR_FLAG_MAX = __NL80211_MNTR_FLAG_AFTER_LAST - 1 }; +/** + * enum nl80211_meshconf_params - mesh configuration parameters + * + * Mesh configuration parameters + * + * @__NL80211_MESHCONF_INVALID: internal use + * + * @NL80211_MESHCONF_RETRY_TIMEOUT: specifies the initial retry timeout in + * millisecond units, used by the Peer Link Open message + * + * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the inital confirm timeout, in + * millisecond units, used by the peer link management to close a peer link + * + * @NL80211_MESHCONF_HOLDING_TIMEOUT: specifies the holding timeout, in + * millisecond units + * + * @NL80211_MESHCONF_MAX_PEER_LINKS: maximum number of peer links allowed + * on this mesh interface + * + * @NL80211_MESHCONF_MAX_RETRIES: specifies the maximum number of peer link + * open retries that can be sent to establish a new peer link instance in a + * mesh + * + * @NL80211_MESHCONF_TTL: specifies the value of TTL field set at a source mesh + * point. + * + * @NL80211_MESHCONF_AUTO_OPEN_PLINKS: whether we should automatically + * open peer links when we detect compatible mesh peers. + * + * @NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES: the number of action frames + * containing a PREQ that an MP can send to a particular destination (path + * target) + * + * @NL80211_MESHCONF_PATH_REFRESH_TIME: how frequently to refresh mesh paths + * (in milliseconds) + * + * @NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT: minimum length of time to wait + * until giving up on a path discovery (in milliseconds) + * + * @NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT: The time (in TUs) for which mesh + * points receiving a PREQ shall consider the forwarding information from the + * root to be valid. (TU = time unit) + * + * @NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL: The minimum interval of time (in + * TUs) during which an MP can send only one action frame containing a PREQ + * reference element + * + * @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs) + * that it takes for an HWMP information element to propagate across the mesh + * + * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute + * + * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use + */ +enum nl80211_meshconf_params { + __NL80211_MESHCONF_INVALID, + NL80211_MESHCONF_RETRY_TIMEOUT, + NL80211_MESHCONF_CONFIRM_TIMEOUT, + NL80211_MESHCONF_HOLDING_TIMEOUT, + NL80211_MESHCONF_MAX_PEER_LINKS, + NL80211_MESHCONF_MAX_RETRIES, + NL80211_MESHCONF_TTL, + NL80211_MESHCONF_AUTO_OPEN_PLINKS, + NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES, + NL80211_MESHCONF_PATH_REFRESH_TIME, + NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT, + NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT, + NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL, + NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME, + + /* keep last */ + __NL80211_MESHCONF_ATTR_AFTER_LAST, + NL80211_MESHCONF_ATTR_MAX = __NL80211_MESHCONF_ATTR_AFTER_LAST - 1 +}; + +/** + * enum nl80211_txq_attr - TX queue parameter attributes + * @__NL80211_TXQ_ATTR_INVALID: Attribute number 0 is reserved + * @NL80211_TXQ_ATTR_QUEUE: TX queue identifier (NL80211_TXQ_Q_*) + * @NL80211_TXQ_ATTR_TXOP: Maximum burst time in units of 32 usecs, 0 meaning + * disabled + * @NL80211_TXQ_ATTR_CWMIN: Minimum contention window [a value of the form + * 2^n-1 in the range 1..32767] + * @NL80211_TXQ_ATTR_CWMAX: Maximum contention window [a value of the form + * 2^n-1 in the range 1..32767] + * @NL80211_TXQ_ATTR_AIFS: Arbitration interframe space [0..255] + * @__NL80211_TXQ_ATTR_AFTER_LAST: Internal + * @NL80211_TXQ_ATTR_MAX: Maximum TXQ attribute number + */ +enum nl80211_txq_attr { + __NL80211_TXQ_ATTR_INVALID, + NL80211_TXQ_ATTR_QUEUE, + NL80211_TXQ_ATTR_TXOP, + NL80211_TXQ_ATTR_CWMIN, + NL80211_TXQ_ATTR_CWMAX, + NL80211_TXQ_ATTR_AIFS, + + /* keep last */ + __NL80211_TXQ_ATTR_AFTER_LAST, + NL80211_TXQ_ATTR_MAX = __NL80211_TXQ_ATTR_AFTER_LAST - 1 +}; + +enum nl80211_txq_q { + NL80211_TXQ_Q_VO, + NL80211_TXQ_Q_VI, + NL80211_TXQ_Q_BE, + NL80211_TXQ_Q_BK +}; + #endif /* __LINUX_NL80211_H */ |