diff options
Diffstat (limited to 'include/linux/pm.h')
| -rw-r--r-- | include/linux/pm.h | 71 |
1 files changed, 43 insertions, 28 deletions
diff --git a/include/linux/pm.h b/include/linux/pm.h index 8c6583a53a0..d915d0345fa 100644 --- a/include/linux/pm.h +++ b/include/linux/pm.h @@ -264,9 +264,9 @@ typedef struct pm_message { * registers, so that it is fully operational. * * @runtime_idle: Device appears to be inactive and it might be put into a - * low-power state if all of the necessary conditions are satisfied. Check - * these conditions and handle the device as appropriate, possibly queueing - * a suspend request for it. The return value is ignored by the PM core. + * low-power state if all of the necessary conditions are satisfied. + * Check these conditions, and return 0 if it's appropriate to let the PM + * core queue a suspend request for the device. * * Refer to Documentation/power/runtime_pm.txt for more information about the * role of the above callbacks in device runtime power management. @@ -352,7 +352,7 @@ const struct dev_pm_ops name = { \ /* * Use this for defining a set of PM operations to be used in all situations - * (sustem suspend, hibernation or runtime PM). + * (system suspend, hibernation or runtime PM). * NOTE: In general, system suspend callbacks, .suspend() and .resume(), should * be different from the corresponding runtime PM callbacks, .runtime_suspend(), * and .runtime_resume(), because .runtime_suspend() always works on an already @@ -379,7 +379,7 @@ const struct dev_pm_ops name = { \ * * ON No transition. * - * FREEZE System is going to hibernate, call ->prepare() and ->freeze() + * FREEZE System is going to hibernate, call ->prepare() and ->freeze() * for all devices. * * SUSPEND System is going to suspend, call ->prepare() and ->suspend() @@ -423,7 +423,7 @@ const struct dev_pm_ops name = { \ #define PM_EVENT_INVALID (-1) #define PM_EVENT_ON 0x0000 -#define PM_EVENT_FREEZE 0x0001 +#define PM_EVENT_FREEZE 0x0001 #define PM_EVENT_SUSPEND 0x0002 #define PM_EVENT_HIBERNATE 0x0004 #define PM_EVENT_QUIESCE 0x0008 @@ -542,6 +542,8 @@ struct dev_pm_info { unsigned int async_suspend:1; bool is_prepared:1; /* Owned by the PM core */ bool is_suspended:1; /* Ditto */ + bool is_noirq_suspended:1; + bool is_late_suspended:1; bool ignore_children:1; bool early_init:1; /* Owned by the PM core */ spinlock_t lock; @@ -582,6 +584,7 @@ struct dev_pm_info { unsigned long accounting_timestamp; #endif struct pm_subsys_data *subsys_data; /* Owned by the subsystem. */ + void (*set_latency_tolerance)(struct device *, s32); struct dev_pm_qos *qos; }; @@ -612,11 +615,11 @@ struct dev_pm_domain { * message is implicit: * * ON Driver starts working again, responding to hardware events - * and software requests. The hardware may have gone through - * a power-off reset, or it may have maintained state from the - * previous suspend() which the driver will rely on while - * resuming. On most platforms, there are no restrictions on - * availability of resources like clocks during resume(). + * and software requests. The hardware may have gone through + * a power-off reset, or it may have maintained state from the + * previous suspend() which the driver will rely on while + * resuming. On most platforms, there are no restrictions on + * availability of resources like clocks during resume(). * * Other transitions are triggered by messages sent using suspend(). All * these transitions quiesce the driver, so that I/O queues are inactive. @@ -626,21 +629,21 @@ struct dev_pm_domain { * differ according to the message: * * SUSPEND Quiesce, enter a low power device state appropriate for - * the upcoming system state (such as PCI_D3hot), and enable - * wakeup events as appropriate. + * the upcoming system state (such as PCI_D3hot), and enable + * wakeup events as appropriate. * * HIBERNATE Enter a low power device state appropriate for the hibernation - * state (eg. ACPI S4) and enable wakeup events as appropriate. + * state (eg. ACPI S4) and enable wakeup events as appropriate. * * FREEZE Quiesce operations so that a consistent image can be saved; - * but do NOT otherwise enter a low power device state, and do - * NOT emit system wakeup events. + * but do NOT otherwise enter a low power device state, and do + * NOT emit system wakeup events. * * PRETHAW Quiesce as if for FREEZE; additionally, prepare for restoring - * the system from a snapshot taken after an earlier FREEZE. - * Some drivers will need to reset their hardware state instead - * of preserving it, to ensure that it's never mistaken for the - * state which that earlier snapshot had set up. + * the system from a snapshot taken after an earlier FREEZE. + * Some drivers will need to reset their hardware state instead + * of preserving it, to ensure that it's never mistaken for the + * state which that earlier snapshot had set up. * * A minimally power-aware driver treats all messages as SUSPEND, fully * reinitializes its device during resume() -- whether or not it was reset @@ -717,14 +720,26 @@ static inline void dpm_for_each_dev(void *data, void (*fn)(struct device *, void { } -#define pm_generic_prepare NULL -#define pm_generic_suspend NULL -#define pm_generic_resume NULL -#define pm_generic_freeze NULL -#define pm_generic_thaw NULL -#define pm_generic_restore NULL -#define pm_generic_poweroff NULL -#define pm_generic_complete NULL +#define pm_generic_prepare NULL +#define pm_generic_suspend_late NULL +#define pm_generic_suspend_noirq NULL +#define pm_generic_suspend NULL +#define pm_generic_resume_early NULL +#define pm_generic_resume_noirq NULL +#define pm_generic_resume NULL +#define pm_generic_freeze_noirq NULL +#define pm_generic_freeze_late NULL +#define pm_generic_freeze NULL +#define pm_generic_thaw_noirq NULL +#define pm_generic_thaw_early NULL +#define pm_generic_thaw NULL +#define pm_generic_restore_noirq NULL +#define pm_generic_restore_early NULL +#define pm_generic_restore NULL +#define pm_generic_poweroff_noirq NULL +#define pm_generic_poweroff_late NULL +#define pm_generic_poweroff NULL +#define pm_generic_complete NULL #endif /* !CONFIG_PM_SLEEP */ /* How to reorder dpm_list after device_move() */ |