diff options
Diffstat (limited to 'include/linux/power')
| -rw-r--r-- | include/linux/power/max17042_battery.h | 93 | ||||
| -rw-r--r-- | include/linux/power/smb347-charger.h | 117 |
2 files changed, 201 insertions, 9 deletions
diff --git a/include/linux/power/max17042_battery.h b/include/linux/power/max17042_battery.h index fe99211fb2b..e01b167e66f 100644 --- a/include/linux/power/max17042_battery.h +++ b/include/linux/power/max17042_battery.h @@ -27,6 +27,8 @@ #define MAX17042_BATTERY_FULL (100) #define MAX17042_DEFAULT_SNS_RESISTOR (10000) +#define MAX17042_CHARACTERIZATION_DATA_SIZE 48 + enum max17042_register { MAX17042_STATUS = 0x00, MAX17042_VALRT_Th = 0x01, @@ -40,11 +42,11 @@ enum max17042_register { MAX17042_VCELL = 0x09, MAX17042_Current = 0x0A, MAX17042_AvgCurrent = 0x0B, - MAX17042_Qresidual = 0x0C, + MAX17042_SOC = 0x0D, MAX17042_AvSOC = 0x0E, MAX17042_RemCap = 0x0F, - MAX17402_FullCAP = 0x10, + MAX17042_FullCAP = 0x10, MAX17042_TTE = 0x11, MAX17042_V_empty = 0x12, @@ -62,14 +64,14 @@ enum max17042_register { MAX17042_AvCap = 0x1F, MAX17042_ManName = 0x20, MAX17042_DevName = 0x21, - MAX17042_DevChem = 0x22, + MAX17042_FullCAPNom = 0x23, MAX17042_TempNom = 0x24, - MAX17042_TempCold = 0x25, + MAX17042_TempLim = 0x25, MAX17042_TempHot = 0x26, MAX17042_AIN = 0x27, MAX17042_LearnCFG = 0x28, - MAX17042_SHFTCFG = 0x29, + MAX17042_FilterCFG = 0x29, MAX17042_RelaxCFG = 0x2A, MAX17042_MiscCFG = 0x2B, MAX17042_TGAIN = 0x2C, @@ -77,22 +79,41 @@ enum max17042_register { MAX17042_CGAIN = 0x2E, MAX17042_COFF = 0x2F, - MAX17042_Q_empty = 0x33, + MAX17042_MaskSOC = 0x32, + MAX17042_SOC_empty = 0x33, MAX17042_T_empty = 0x34, + MAX17042_FullCAP0 = 0x35, + MAX17042_LAvg_empty = 0x36, + MAX17042_FCTC = 0x37, MAX17042_RCOMP0 = 0x38, MAX17042_TempCo = 0x39, - MAX17042_Rx = 0x3A, - MAX17042_T_empty0 = 0x3B, + MAX17042_EmptyTempCo = 0x3A, + MAX17042_K_empty0 = 0x3B, MAX17042_TaskPeriod = 0x3C, MAX17042_FSTAT = 0x3D, MAX17042_SHDNTIMER = 0x3F, - MAX17042_VFRemCap = 0x4A, + MAX17042_dQacc = 0x45, + MAX17042_dPacc = 0x46, + + MAX17042_VFSOC0 = 0x48, MAX17042_QH = 0x4D, MAX17042_QL = 0x4E, + + MAX17042_VFSOC0Enable = 0x60, + MAX17042_MLOCKReg1 = 0x62, + MAX17042_MLOCKReg2 = 0x63, + + MAX17042_MODELChrTbl = 0x80, + + MAX17042_OCV = 0xEE, + + MAX17042_OCVInternal = 0xFB, + + MAX17042_VFSOC = 0xFF, }; /* @@ -105,10 +126,64 @@ struct max17042_reg_data { u16 data; }; +struct max17042_config_data { + /* External current sense resistor value in milli-ohms */ + u32 cur_sense_val; + + /* A/D measurement */ + u16 tgain; /* 0x2C */ + u16 toff; /* 0x2D */ + u16 cgain; /* 0x2E */ + u16 coff; /* 0x2F */ + + /* Alert / Status */ + u16 valrt_thresh; /* 0x01 */ + u16 talrt_thresh; /* 0x02 */ + u16 soc_alrt_thresh; /* 0x03 */ + u16 config; /* 0x01D */ + u16 shdntimer; /* 0x03F */ + + /* App data */ + u16 design_cap; /* 0x18 */ + u16 ichgt_term; /* 0x1E */ + + /* MG3 config */ + u16 at_rate; /* 0x04 */ + u16 learn_cfg; /* 0x28 */ + u16 filter_cfg; /* 0x29 */ + u16 relax_cfg; /* 0x2A */ + u16 misc_cfg; /* 0x2B */ + u16 masksoc; /* 0x32 */ + + /* MG3 save and restore */ + u16 fullcap; /* 0x10 */ + u16 fullcapnom; /* 0x23 */ + u16 socempty; /* 0x33 */ + u16 lavg_empty; /* 0x36 */ + u16 dqacc; /* 0x45 */ + u16 dpacc; /* 0x46 */ + + /* Cell technology from power_supply.h */ + u16 cell_technology; + + /* Cell Data */ + u16 vempty; /* 0x12 */ + u16 temp_nom; /* 0x24 */ + u16 temp_lim; /* 0x25 */ + u16 fctc; /* 0x37 */ + u16 rcomp0; /* 0x38 */ + u16 tcompc0; /* 0x39 */ + u16 empty_tempco; /* 0x3A */ + u16 kempty0; /* 0x3B */ + u16 cell_char_tbl[MAX17042_CHARACTERIZATION_DATA_SIZE]; +} __packed; + struct max17042_platform_data { struct max17042_reg_data *init_data; + struct max17042_config_data *config_data; int num_init_data; /* Number of enties in init_data array */ bool enable_current_sense; + bool enable_por_init; /* Use POR init from Maxim appnote */ /* * R_sns in micro-ohms. diff --git a/include/linux/power/smb347-charger.h b/include/linux/power/smb347-charger.h new file mode 100644 index 00000000000..b3cb20dab55 --- /dev/null +++ b/include/linux/power/smb347-charger.h @@ -0,0 +1,117 @@ +/* + * Summit Microelectronics SMB347 Battery Charger Driver + * + * Copyright (C) 2011, Intel Corporation + * + * Authors: Bruce E. Robertson <bruce.e.robertson@intel.com> + * Mika Westerberg <mika.westerberg@linux.intel.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef SMB347_CHARGER_H +#define SMB347_CHARGER_H + +#include <linux/types.h> +#include <linux/power_supply.h> + +enum { + /* use the default compensation method */ + SMB347_SOFT_TEMP_COMPENSATE_DEFAULT = -1, + + SMB347_SOFT_TEMP_COMPENSATE_NONE, + SMB347_SOFT_TEMP_COMPENSATE_CURRENT, + SMB347_SOFT_TEMP_COMPENSATE_VOLTAGE, +}; + +/* Use default factory programmed value for hard/soft temperature limit */ +#define SMB347_TEMP_USE_DEFAULT -273 + +/* + * Charging enable can be controlled by software (via i2c) by + * smb347-charger driver or by EN pin (active low/high). + */ +enum smb347_chg_enable { + SMB347_CHG_ENABLE_SW, + SMB347_CHG_ENABLE_PIN_ACTIVE_LOW, + SMB347_CHG_ENABLE_PIN_ACTIVE_HIGH, +}; + +/** + * struct smb347_charger_platform_data - platform data for SMB347 charger + * @battery_info: Information about the battery + * @max_charge_current: maximum current (in uA) the battery can be charged + * @max_charge_voltage: maximum voltage (in uV) the battery can be charged + * @pre_charge_current: current (in uA) to use in pre-charging phase + * @termination_current: current (in uA) used to determine when the + * charging cycle terminates + * @pre_to_fast_voltage: voltage (in uV) treshold used for transitioning to + * pre-charge to fast charge mode + * @mains_current_limit: maximum input current drawn from AC/DC input (in uA) + * @usb_hc_current_limit: maximum input high current (in uA) drawn from USB + * input + * @chip_temp_threshold: die temperature where device starts limiting charge + * current [%100 - %130] (in degree C) + * @soft_cold_temp_limit: soft cold temperature limit [%0 - %15] (in degree C), + * granularity is 5 deg C. + * @soft_hot_temp_limit: soft hot temperature limit [%40 - %55] (in degree C), + * granularity is 5 deg C. + * @hard_cold_temp_limit: hard cold temperature limit [%-5 - %10] (in degree C), + * granularity is 5 deg C. + * @hard_hot_temp_limit: hard hot temperature limit [%50 - %65] (in degree C), + * granularity is 5 deg C. + * @suspend_on_hard_temp_limit: suspend charging when hard limit is hit + * @soft_temp_limit_compensation: compensation method when soft temperature + * limit is hit + * @charge_current_compensation: current (in uA) for charging compensation + * current when temperature hits soft limits + * @use_mains: AC/DC input can be used + * @use_usb: USB input can be used + * @use_usb_otg: USB OTG output can be used (not implemented yet) + * @irq_gpio: GPIO number used for interrupts (%-1 if not used) + * @enable_control: how charging enable/disable is controlled + * (driver/pin controls) + * + * @use_main, @use_usb, and @use_usb_otg are means to enable/disable + * hardware support for these. This is useful when we want to have for + * example OTG charging controlled via OTG transceiver driver and not by + * the SMB347 hardware. + * + * Hard and soft temperature limit values are given as described in the + * device data sheet and assuming NTC beta value is %3750. Even if this is + * not the case, these values should be used. They can be mapped to the + * corresponding NTC beta values with the help of table %2 in the data + * sheet. So for example if NTC beta is %3375 and we want to program hard + * hot limit to be %53 deg C, @hard_hot_temp_limit should be set to %50. + * + * If zero value is given in any of the current and voltage values, the + * factory programmed default will be used. For soft/hard temperature + * values, pass in %SMB347_TEMP_USE_DEFAULT instead. + */ +struct smb347_charger_platform_data { + struct power_supply_info battery_info; + unsigned int max_charge_current; + unsigned int max_charge_voltage; + unsigned int pre_charge_current; + unsigned int termination_current; + unsigned int pre_to_fast_voltage; + unsigned int mains_current_limit; + unsigned int usb_hc_current_limit; + unsigned int chip_temp_threshold; + int soft_cold_temp_limit; + int soft_hot_temp_limit; + int hard_cold_temp_limit; + int hard_hot_temp_limit; + bool suspend_on_hard_temp_limit; + unsigned int soft_temp_limit_compensation; + unsigned int charge_current_compensation; + bool use_mains; + bool use_usb; + bool use_usb_otg; + int irq_gpio; + enum smb347_chg_enable enable_control; +}; + +#endif /* SMB347_CHARGER_H */ |