4 files changed, 50 insertions, 0 deletions
diff --git a/include/linux/spi/eeprom.h b/include/linux/spi/eeprom.h
index 1085212c446..306e7b1c69e 100644
--- a/include/linux/spi/eeprom.h
+++ b/include/linux/spi/eeprom.h
@@ -1,6 +1,8 @@
 #ifndef __LINUX_SPI_EEPROM_H
 #define __LINUX_SPI_EEPROM_H
 
+#include <linux/memory.h>
+
 /*
  * Put one of these structures in platform_data for SPI EEPROMS handled
  * by the "at25" driver.  On SPI, most EEPROMS understand the same core
@@ -17,6 +19,10 @@ struct spi_eeprom {
 #define	EE_ADDR2	0x0002			/* 16 bit addrs */
 #define	EE_ADDR3	0x0004			/* 24 bit addrs */
 #define	EE_READONLY	0x0008			/* disallow writes */
+
+	/* for exporting this chip's data to other kernel code */
+	void (*setup)(struct memory_accessor *mem, void *context);
+	void *context;
 };
 
 #endif /* __LINUX_SPI_EEPROM_H */
diff --git a/include/linux/spi/libertas_spi.h b/include/linux/spi/libertas_spi.h
new file mode 100644
index 00000000000..79506f5f9e6
--- /dev/null
+++ b/include/linux/spi/libertas_spi.h
@@ -0,0 +1,32 @@
+/*
+ * board-specific data for the libertas_spi driver.
+ *
+ * Copyright 2008 Analog Devices Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ */
+#ifndef _LIBERTAS_SPI_H_
+#define _LIBERTAS_SPI_H_
+
+struct spi_device;
+
+struct libertas_spi_platform_data {
+	/* There are two ways to read data from the WLAN module's SPI
+	 * interface. Setting 0 or 1 here controls which one is used.
+	 *
+	 * Usually you want to set use_dummy_writes = 1.
+	 * However, if that doesn't work or if you are using a slow SPI clock
+	 * speed, you may want to use 0 here. */
+	u16 use_dummy_writes;
+
+	/* GPIO number to use as chip select */
+	u16 gpio_cs;
+
+	/* Board specific setup/teardown */
+	int (*setup)(struct spi_device *spi);
+	int (*teardown)(struct spi_device *spi);
+};
+#endif
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index 68bb1c501d0..2cc43fa380c 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -204,6 +204,7 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv)
  *	SPI slaves, and are numbered from zero to num_chipselects.
  *	each slave has a chipselect signal, but it's common that not
  *	every chipselect is connected to a slave.
+ * @dma_alignment: SPI controller constraint on DMA buffers alignment.
  * @setup: updates the device mode and clocking records used by a
  *	device's SPI controller; protocol code may call this.  This
  *	must fail if an unrecognized or unsupported mode is requested.
@@ -239,6 +240,11 @@ struct spi_master {
 	 */
 	u16			num_chipselect;
 
+	/* some SPI controllers pose alignment requirements on DMAable
+	 * buffers; let protocol drivers know about these requirements.
+	 */
+	u16			dma_alignment;
+
 	/* setup mode and clock, etc (spi driver may call many times) */
 	int			(*setup)(struct spi_device *spi);
 
diff --git a/include/linux/spi/spi_gpio.h b/include/linux/spi/spi_gpio.h
index 0f01a0f1f40..ca6782ee4b9 100644
--- a/include/linux/spi/spi_gpio.h
+++ b/include/linux/spi/spi_gpio.h
@@ -25,10 +25,16 @@
  *	...
  *	};
  *
+ * If chipselect is not used (there's only one device on the bus), assign
+ * SPI_GPIO_NO_CHIPSELECT to the controller_data:
+ *		.controller_data = (void *) SPI_GPIO_NO_CHIPSELECT;
+ *
  * If the bitbanged bus is later switched to a "native" controller,
  * that platform_device and controller_data should be removed.
  */
 
+#define SPI_GPIO_NO_CHIPSELECT		((unsigned long)-1l)
+
 /**
  * struct spi_gpio_platform_data - parameter for bitbanged SPI master
  * @sck: number of the GPIO used for clock output