diff options
Diffstat (limited to 'include/linux/usb/r8a66597.h')
| -rw-r--r-- | include/linux/usb/r8a66597.h | 375 |
1 files changed, 373 insertions, 2 deletions
diff --git a/include/linux/usb/r8a66597.h b/include/linux/usb/r8a66597.h index e9f0384fa20..26d21673405 100644 --- a/include/linux/usb/r8a66597.h +++ b/include/linux/usb/r8a66597.h @@ -28,9 +28,12 @@ #define R8A66597_PLATDATA_XTAL_48MHZ 0x03 struct r8a66597_platdata { - /* This ops can controll port power instead of DVSTCTR register. */ + /* This callback can control port power instead of DVSTCTR register. */ void (*port_power)(int port, int power); + /* set one = on chip controller, set zero = external controller */ + unsigned on_chip:1; + /* (external controller only) set R8A66597_PLATDATA_XTAL_nnMHZ */ unsigned xtal:2; @@ -40,5 +43,373 @@ struct r8a66597_platdata { /* set one = big endian, set zero = little endian */ unsigned endian:1; }; -#endif + +/* Register definitions */ +#define SYSCFG0 0x00 +#define SYSCFG1 0x02 +#define SYSSTS0 0x04 +#define SYSSTS1 0x06 +#define DVSTCTR0 0x08 +#define DVSTCTR1 0x0A +#define TESTMODE 0x0C +#define PINCFG 0x0E +#define DMA0CFG 0x10 +#define DMA1CFG 0x12 +#define CFIFO 0x14 +#define D0FIFO 0x18 +#define D1FIFO 0x1C +#define CFIFOSEL 0x20 +#define CFIFOCTR 0x22 +#define CFIFOSIE 0x24 +#define D0FIFOSEL 0x28 +#define D0FIFOCTR 0x2A +#define D1FIFOSEL 0x2C +#define D1FIFOCTR 0x2E +#define INTENB0 0x30 +#define INTENB1 0x32 +#define INTENB2 0x34 +#define BRDYENB 0x36 +#define NRDYENB 0x38 +#define BEMPENB 0x3A +#define SOFCFG 0x3C +#define INTSTS0 0x40 +#define INTSTS1 0x42 +#define INTSTS2 0x44 +#define BRDYSTS 0x46 +#define NRDYSTS 0x48 +#define BEMPSTS 0x4A +#define FRMNUM 0x4C +#define UFRMNUM 0x4E +#define USBADDR 0x50 +#define USBREQ 0x54 +#define USBVAL 0x56 +#define USBINDX 0x58 +#define USBLENG 0x5A +#define DCPCFG 0x5C +#define DCPMAXP 0x5E +#define DCPCTR 0x60 +#define PIPESEL 0x64 +#define PIPECFG 0x68 +#define PIPEBUF 0x6A +#define PIPEMAXP 0x6C +#define PIPEPERI 0x6E +#define PIPE1CTR 0x70 +#define PIPE2CTR 0x72 +#define PIPE3CTR 0x74 +#define PIPE4CTR 0x76 +#define PIPE5CTR 0x78 +#define PIPE6CTR 0x7A +#define PIPE7CTR 0x7C +#define PIPE8CTR 0x7E +#define PIPE9CTR 0x80 +#define PIPE1TRE 0x90 +#define PIPE1TRN 0x92 +#define PIPE2TRE 0x94 +#define PIPE2TRN 0x96 +#define PIPE3TRE 0x98 +#define PIPE3TRN 0x9A +#define PIPE4TRE 0x9C +#define PIPE4TRN 0x9E +#define PIPE5TRE 0xA0 +#define PIPE5TRN 0xA2 +#define DEVADD0 0xD0 +#define DEVADD1 0xD2 +#define DEVADD2 0xD4 +#define DEVADD3 0xD6 +#define DEVADD4 0xD8 +#define DEVADD5 0xDA +#define DEVADD6 0xDC +#define DEVADD7 0xDE +#define DEVADD8 0xE0 +#define DEVADD9 0xE2 +#define DEVADDA 0xE4 + +/* System Configuration Control Register */ +#define XTAL 0xC000 /* b15-14: Crystal selection */ +#define XTAL48 0x8000 /* 48MHz */ +#define XTAL24 0x4000 /* 24MHz */ +#define XTAL12 0x0000 /* 12MHz */ +#define XCKE 0x2000 /* b13: External clock enable */ +#define PLLC 0x0800 /* b11: PLL control */ +#define SCKE 0x0400 /* b10: USB clock enable */ +#define PCSDIS 0x0200 /* b9: not CS wakeup */ +#define LPSME 0x0100 /* b8: Low power sleep mode */ +#define HSE 0x0080 /* b7: Hi-speed enable */ +#define DCFM 0x0040 /* b6: Controller function select */ +#define DRPD 0x0020 /* b5: D+/- pull down control */ +#define DPRPU 0x0010 /* b4: D+ pull up control */ +#define USBE 0x0001 /* b0: USB module operation enable */ + +/* System Configuration Status Register */ +#define OVCBIT 0x8000 /* b15-14: Over-current bit */ +#define OVCMON 0xC000 /* b15-14: Over-current monitor */ +#define SOFEA 0x0020 /* b5: SOF monitor */ +#define IDMON 0x0004 /* b3: ID-pin monitor */ +#define LNST 0x0003 /* b1-0: D+, D- line status */ +#define SE1 0x0003 /* SE1 */ +#define FS_KSTS 0x0002 /* Full-Speed K State */ +#define FS_JSTS 0x0001 /* Full-Speed J State */ +#define LS_JSTS 0x0002 /* Low-Speed J State */ +#define LS_KSTS 0x0001 /* Low-Speed K State */ +#define SE0 0x0000 /* SE0 */ + +/* Device State Control Register */ +#define EXTLP0 0x0400 /* b10: External port */ +#define VBOUT 0x0200 /* b9: VBUS output */ +#define WKUP 0x0100 /* b8: Remote wakeup */ +#define RWUPE 0x0080 /* b7: Remote wakeup sense */ +#define USBRST 0x0040 /* b6: USB reset enable */ +#define RESUME 0x0020 /* b5: Resume enable */ +#define UACT 0x0010 /* b4: USB bus enable */ +#define RHST 0x0007 /* b1-0: Reset handshake status */ +#define HSPROC 0x0004 /* HS handshake is processing */ +#define HSMODE 0x0003 /* Hi-Speed mode */ +#define FSMODE 0x0002 /* Full-Speed mode */ +#define LSMODE 0x0001 /* Low-Speed mode */ +#define UNDECID 0x0000 /* Undecided */ + +/* Test Mode Register */ +#define UTST 0x000F /* b3-0: Test select */ +#define H_TST_PACKET 0x000C /* HOST TEST Packet */ +#define H_TST_SE0_NAK 0x000B /* HOST TEST SE0 NAK */ +#define H_TST_K 0x000A /* HOST TEST K */ +#define H_TST_J 0x0009 /* HOST TEST J */ +#define H_TST_NORMAL 0x0000 /* HOST Normal Mode */ +#define P_TST_PACKET 0x0004 /* PERI TEST Packet */ +#define P_TST_SE0_NAK 0x0003 /* PERI TEST SE0 NAK */ +#define P_TST_K 0x0002 /* PERI TEST K */ +#define P_TST_J 0x0001 /* PERI TEST J */ +#define P_TST_NORMAL 0x0000 /* PERI Normal Mode */ + +/* Data Pin Configuration Register */ +#define LDRV 0x8000 /* b15: Drive Current Adjust */ +#define VIF1 0x0000 /* VIF = 1.8V */ +#define VIF3 0x8000 /* VIF = 3.3V */ +#define INTA 0x0001 /* b1: USB INT-pin active */ + +/* DMAx Pin Configuration Register */ +#define DREQA 0x4000 /* b14: Dreq active select */ +#define BURST 0x2000 /* b13: Burst mode */ +#define DACKA 0x0400 /* b10: Dack active select */ +#define DFORM 0x0380 /* b9-7: DMA mode select */ +#define CPU_ADR_RD_WR 0x0000 /* Address + RD/WR mode (CPU bus) */ +#define CPU_DACK_RD_WR 0x0100 /* DACK + RD/WR mode (CPU bus) */ +#define CPU_DACK_ONLY 0x0180 /* DACK only mode (CPU bus) */ +#define SPLIT_DACK_ONLY 0x0200 /* DACK only mode (SPLIT bus) */ +#define DENDA 0x0040 /* b6: Dend active select */ +#define PKTM 0x0020 /* b5: Packet mode */ +#define DENDE 0x0010 /* b4: Dend enable */ +#define OBUS 0x0004 /* b2: OUTbus mode */ + +/* CFIFO/DxFIFO Port Select Register */ +#define RCNT 0x8000 /* b15: Read count mode */ +#define REW 0x4000 /* b14: Buffer rewind */ +#define DCLRM 0x2000 /* b13: DMA buffer clear mode */ +#define DREQE 0x1000 /* b12: DREQ output enable */ +#define MBW_8 0x0000 /* 8bit */ +#define MBW_16 0x0400 /* 16bit */ +#define MBW_32 0x0800 /* 32bit */ +#define BIGEND 0x0100 /* b8: Big endian mode */ +#define BYTE_LITTLE 0x0000 /* little dendian */ +#define BYTE_BIG 0x0100 /* big endifan */ +#define ISEL 0x0020 /* b5: DCP FIFO port direction select */ +#define CURPIPE 0x000F /* b2-0: PIPE select */ + +/* CFIFO/DxFIFO Port Control Register */ +#define BVAL 0x8000 /* b15: Buffer valid flag */ +#define BCLR 0x4000 /* b14: Buffer clear */ +#define FRDY 0x2000 /* b13: FIFO ready */ +#define DTLN 0x0FFF /* b11-0: FIFO received data length */ + +/* Interrupt Enable Register 0 */ +#define VBSE 0x8000 /* b15: VBUS interrupt */ +#define RSME 0x4000 /* b14: Resume interrupt */ +#define SOFE 0x2000 /* b13: Frame update interrupt */ +#define DVSE 0x1000 /* b12: Device state transition interrupt */ +#define CTRE 0x0800 /* b11: Control transfer stage transition interrupt */ +#define BEMPE 0x0400 /* b10: Buffer empty interrupt */ +#define NRDYE 0x0200 /* b9: Buffer not ready interrupt */ +#define BRDYE 0x0100 /* b8: Buffer ready interrupt */ + +/* Interrupt Enable Register 1 */ +#define OVRCRE 0x8000 /* b15: Over-current interrupt */ +#define BCHGE 0x4000 /* b14: USB us chenge interrupt */ +#define DTCHE 0x1000 /* b12: Detach sense interrupt */ +#define ATTCHE 0x0800 /* b11: Attach sense interrupt */ +#define EOFERRE 0x0040 /* b6: EOF error interrupt */ +#define SIGNE 0x0020 /* b5: SETUP IGNORE interrupt */ +#define SACKE 0x0010 /* b4: SETUP ACK interrupt */ + +/* BRDY Interrupt Enable/Status Register */ +#define BRDY9 0x0200 /* b9: PIPE9 */ +#define BRDY8 0x0100 /* b8: PIPE8 */ +#define BRDY7 0x0080 /* b7: PIPE7 */ +#define BRDY6 0x0040 /* b6: PIPE6 */ +#define BRDY5 0x0020 /* b5: PIPE5 */ +#define BRDY4 0x0010 /* b4: PIPE4 */ +#define BRDY3 0x0008 /* b3: PIPE3 */ +#define BRDY2 0x0004 /* b2: PIPE2 */ +#define BRDY1 0x0002 /* b1: PIPE1 */ +#define BRDY0 0x0001 /* b1: PIPE0 */ + +/* NRDY Interrupt Enable/Status Register */ +#define NRDY9 0x0200 /* b9: PIPE9 */ +#define NRDY8 0x0100 /* b8: PIPE8 */ +#define NRDY7 0x0080 /* b7: PIPE7 */ +#define NRDY6 0x0040 /* b6: PIPE6 */ +#define NRDY5 0x0020 /* b5: PIPE5 */ +#define NRDY4 0x0010 /* b4: PIPE4 */ +#define NRDY3 0x0008 /* b3: PIPE3 */ +#define NRDY2 0x0004 /* b2: PIPE2 */ +#define NRDY1 0x0002 /* b1: PIPE1 */ +#define NRDY0 0x0001 /* b1: PIPE0 */ + +/* BEMP Interrupt Enable/Status Register */ +#define BEMP9 0x0200 /* b9: PIPE9 */ +#define BEMP8 0x0100 /* b8: PIPE8 */ +#define BEMP7 0x0080 /* b7: PIPE7 */ +#define BEMP6 0x0040 /* b6: PIPE6 */ +#define BEMP5 0x0020 /* b5: PIPE5 */ +#define BEMP4 0x0010 /* b4: PIPE4 */ +#define BEMP3 0x0008 /* b3: PIPE3 */ +#define BEMP2 0x0004 /* b2: PIPE2 */ +#define BEMP1 0x0002 /* b1: PIPE1 */ +#define BEMP0 0x0001 /* b0: PIPE0 */ + +/* SOF Pin Configuration Register */ +#define TRNENSEL 0x0100 /* b8: Select transaction enable period */ +#define BRDYM 0x0040 /* b6: BRDY clear timing */ +#define INTL 0x0020 /* b5: Interrupt sense select */ +#define EDGESTS 0x0010 /* b4: */ +#define SOFMODE 0x000C /* b3-2: SOF pin select */ +#define SOF_125US 0x0008 /* SOF OUT 125us Frame Signal */ +#define SOF_1MS 0x0004 /* SOF OUT 1ms Frame Signal */ +#define SOF_DISABLE 0x0000 /* SOF OUT Disable */ + +/* Interrupt Status Register 0 */ +#define VBINT 0x8000 /* b15: VBUS interrupt */ +#define RESM 0x4000 /* b14: Resume interrupt */ +#define SOFR 0x2000 /* b13: SOF frame update interrupt */ +#define DVST 0x1000 /* b12: Device state transition interrupt */ +#define CTRT 0x0800 /* b11: Control transfer stage transition interrupt */ +#define BEMP 0x0400 /* b10: Buffer empty interrupt */ +#define NRDY 0x0200 /* b9: Buffer not ready interrupt */ +#define BRDY 0x0100 /* b8: Buffer ready interrupt */ +#define VBSTS 0x0080 /* b7: VBUS input port */ +#define DVSQ 0x0070 /* b6-4: Device state */ +#define DS_SPD_CNFG 0x0070 /* Suspend Configured */ +#define DS_SPD_ADDR 0x0060 /* Suspend Address */ +#define DS_SPD_DFLT 0x0050 /* Suspend Default */ +#define DS_SPD_POWR 0x0040 /* Suspend Powered */ +#define DS_SUSP 0x0040 /* Suspend */ +#define DS_CNFG 0x0030 /* Configured */ +#define DS_ADDS 0x0020 /* Address */ +#define DS_DFLT 0x0010 /* Default */ +#define DS_POWR 0x0000 /* Powered */ +#define DVSQS 0x0030 /* b5-4: Device state */ +#define VALID 0x0008 /* b3: Setup packet detected flag */ +#define CTSQ 0x0007 /* b2-0: Control transfer stage */ +#define CS_SQER 0x0006 /* Sequence error */ +#define CS_WRND 0x0005 /* Control write nodata status stage */ +#define CS_WRSS 0x0004 /* Control write status stage */ +#define CS_WRDS 0x0003 /* Control write data stage */ +#define CS_RDSS 0x0002 /* Control read status stage */ +#define CS_RDDS 0x0001 /* Control read data stage */ +#define CS_IDST 0x0000 /* Idle or setup stage */ + +/* Interrupt Status Register 1 */ +#define OVRCR 0x8000 /* b15: Over-current interrupt */ +#define BCHG 0x4000 /* b14: USB bus chenge interrupt */ +#define DTCH 0x1000 /* b12: Detach sense interrupt */ +#define ATTCH 0x0800 /* b11: Attach sense interrupt */ +#define EOFERR 0x0040 /* b6: EOF-error interrupt */ +#define SIGN 0x0020 /* b5: Setup ignore interrupt */ +#define SACK 0x0010 /* b4: Setup acknowledge interrupt */ + +/* Frame Number Register */ +#define OVRN 0x8000 /* b15: Overrun error */ +#define CRCE 0x4000 /* b14: Received data error */ +#define FRNM 0x07FF /* b10-0: Frame number */ + +/* Micro Frame Number Register */ +#define UFRNM 0x0007 /* b2-0: Micro frame number */ + +/* Default Control Pipe Maxpacket Size Register */ +/* Pipe Maxpacket Size Register */ +#define DEVSEL 0xF000 /* b15-14: Device address select */ +#define MAXP 0x007F /* b6-0: Maxpacket size of default control pipe */ + +/* Default Control Pipe Control Register */ +#define BSTS 0x8000 /* b15: Buffer status */ +#define SUREQ 0x4000 /* b14: Send USB request */ +#define CSCLR 0x2000 /* b13: complete-split status clear */ +#define CSSTS 0x1000 /* b12: complete-split status */ +#define SUREQCLR 0x0800 /* b11: stop setup request */ +#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */ +#define SQSET 0x0080 /* b7: Sequence toggle bit set */ +#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */ +#define PBUSY 0x0020 /* b5: pipe busy */ +#define PINGE 0x0010 /* b4: ping enable */ +#define CCPL 0x0004 /* b2: Enable control transfer complete */ +#define PID 0x0003 /* b1-0: Response PID */ +#define PID_STALL11 0x0003 /* STALL */ +#define PID_STALL 0x0002 /* STALL */ +#define PID_BUF 0x0001 /* BUF */ +#define PID_NAK 0x0000 /* NAK */ + +/* Pipe Window Select Register */ +#define PIPENM 0x0007 /* b2-0: Pipe select */ + +/* Pipe Configuration Register */ +#define R8A66597_TYP 0xC000 /* b15-14: Transfer type */ +#define R8A66597_ISO 0xC000 /* Isochronous */ +#define R8A66597_INT 0x8000 /* Interrupt */ +#define R8A66597_BULK 0x4000 /* Bulk */ +#define R8A66597_BFRE 0x0400 /* b10: Buffer ready interrupt mode select */ +#define R8A66597_DBLB 0x0200 /* b9: Double buffer mode select */ +#define R8A66597_CNTMD 0x0100 /* b8: Continuous transfer mode select */ +#define R8A66597_SHTNAK 0x0080 /* b7: Transfer end NAK */ +#define R8A66597_DIR 0x0010 /* b4: Transfer direction select */ +#define R8A66597_EPNUM 0x000F /* b3-0: Eendpoint number select */ + +/* Pipe Buffer Configuration Register */ +#define BUFSIZE 0x7C00 /* b14-10: Pipe buffer size */ +#define BUFNMB 0x007F /* b6-0: Pipe buffer number */ +#define PIPE0BUF 256 +#define PIPExBUF 64 + +/* Pipe Maxpacket Size Register */ +#define MXPS 0x07FF /* b10-0: Maxpacket size */ + +/* Pipe Cycle Configuration Register */ +#define IFIS 0x1000 /* b12: Isochronous in-buffer flush mode select */ +#define IITV 0x0007 /* b2-0: Isochronous interval */ + +/* Pipex Control Register */ +#define BSTS 0x8000 /* b15: Buffer status */ +#define INBUFM 0x4000 /* b14: IN buffer monitor (Only for PIPE1 to 5) */ +#define CSCLR 0x2000 /* b13: complete-split status clear */ +#define CSSTS 0x1000 /* b12: complete-split status */ +#define ATREPM 0x0400 /* b10: Auto repeat mode */ +#define ACLRM 0x0200 /* b9: Out buffer auto clear mode */ +#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */ +#define SQSET 0x0080 /* b7: Sequence toggle bit set */ +#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */ +#define PBUSY 0x0020 /* b5: pipe busy */ +#define PID 0x0003 /* b1-0: Response PID */ + +/* PIPExTRE */ +#define TRENB 0x0200 /* b9: Transaction counter enable */ +#define TRCLR 0x0100 /* b8: Transaction counter clear */ + +/* PIPExTRN */ +#define TRNCNT 0xFFFF /* b15-0: Transaction counter */ + +/* DEVADDx */ +#define UPPHUB 0x7800 +#define HUBPORT 0x0700 +#define USBSPD 0x00C0 +#define RTPORT 0x0001 + +#endif /* __LINUX_USB_R8A66597_H */ |