diff options
Diffstat (limited to 'include/media')
-rw-r--r-- | include/media/m5mols.h | 4 | ||||
-rw-r--r-- | include/media/mt9p031.h | 19 | ||||
-rw-r--r-- | include/media/mt9t001.h | 8 | ||||
-rw-r--r-- | include/media/omap3isp.h | 140 | ||||
-rw-r--r-- | include/media/ov772x.h | 26 | ||||
-rw-r--r-- | include/media/rc-core.h | 7 | ||||
-rw-r--r-- | include/media/rc-map.h | 3 | ||||
-rw-r--r-- | include/media/s5k6aa.h | 51 | ||||
-rw-r--r-- | include/media/s5p_fimc.h | 18 | ||||
-rw-r--r-- | include/media/saa7146.h | 39 | ||||
-rw-r--r-- | include/media/soc_camera.h | 104 | ||||
-rw-r--r-- | include/media/soc_camera_platform.h | 4 | ||||
-rw-r--r-- | include/media/soc_mediabus.h | 2 | ||||
-rw-r--r-- | include/media/v4l2-chip-ident.h | 3 | ||||
-rw-r--r-- | include/media/v4l2-ctrls.h | 15 | ||||
-rw-r--r-- | include/media/v4l2-int-device.h | 3 | ||||
-rw-r--r-- | include/media/v4l2-ioctl.h | 2 | ||||
-rw-r--r-- | include/media/v4l2-mediabus.h | 12 | ||||
-rw-r--r-- | include/media/v4l2-subdev.h | 5 | ||||
-rw-r--r-- | include/media/videobuf2-core.h | 71 | ||||
-rw-r--r-- | include/media/videobuf2-dma-contig.h | 6 |
21 files changed, 384 insertions, 158 deletions
diff --git a/include/media/m5mols.h b/include/media/m5mols.h index aac2c0e06d5..4a825ae5c6c 100644 --- a/include/media/m5mols.h +++ b/include/media/m5mols.h @@ -18,15 +18,13 @@ /** * struct m5mols_platform_data - platform data for M-5MOLS driver - * @irq: GPIO getting the irq pin of M-5MOLS * @gpio_reset: GPIO driving the reset pin of M-5MOLS - * @reset_polarity: active state for gpio_rst pin, 0 or 1 + * @reset_polarity: active state for gpio_reset pin, 0 or 1 * @set_power: an additional callback to the board setup code * to be called after enabling and before disabling * the sensor's supply regulators */ struct m5mols_platform_data { - int irq; int gpio_reset; u8 reset_polarity; int (*set_power)(struct device *dev, int on); diff --git a/include/media/mt9p031.h b/include/media/mt9p031.h new file mode 100644 index 00000000000..96448c7a318 --- /dev/null +++ b/include/media/mt9p031.h @@ -0,0 +1,19 @@ +#ifndef MT9P031_H +#define MT9P031_H + +struct v4l2_subdev; + +enum { + MT9P031_COLOR_VERSION, + MT9P031_MONOCHROME_VERSION, +}; + +struct mt9p031_platform_data { + int (*set_xclk)(struct v4l2_subdev *subdev, int hz); + int (*reset)(struct v4l2_subdev *subdev, int active); + int ext_freq; /* input frequency to the mt9p031 for PLL dividers */ + int target_freq; /* frequency target for the PLL */ + int version; /* MT9P031_COLOR_VERSION or MT9P031_MONOCHROME_VERSION */ +}; + +#endif diff --git a/include/media/mt9t001.h b/include/media/mt9t001.h new file mode 100644 index 00000000000..e839a78bb9c --- /dev/null +++ b/include/media/mt9t001.h @@ -0,0 +1,8 @@ +#ifndef _MEDIA_MT9T001_H +#define _MEDIA_MT9T001_H + +struct mt9t001_platform_data { + unsigned int clk_pol:1; +}; + +#endif diff --git a/include/media/omap3isp.h b/include/media/omap3isp.h new file mode 100644 index 00000000000..e917b1da657 --- /dev/null +++ b/include/media/omap3isp.h @@ -0,0 +1,140 @@ +/* + * omap3isp.h + * + * TI OMAP3 ISP - Platform data + * + * Copyright (C) 2011 Nokia Corporation + * + * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com> + * Sakari Ailus <sakari.ailus@iki.fi> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + */ + +#ifndef __MEDIA_OMAP3ISP_H__ +#define __MEDIA_OMAP3ISP_H__ + +struct i2c_board_info; +struct isp_device; + +enum isp_interface_type { + ISP_INTERFACE_PARALLEL, + ISP_INTERFACE_CSI2A_PHY2, + ISP_INTERFACE_CCP2B_PHY1, + ISP_INTERFACE_CCP2B_PHY2, + ISP_INTERFACE_CSI2C_PHY1, +}; + +enum { + ISP_BRIDGE_DISABLE = 0, + ISP_BRIDGE_LITTLE_ENDIAN = 2, + ISP_BRIDGE_BIG_ENDIAN = 3, +}; + +enum { + ISP_LANE_SHIFT_0 = 0, + ISP_LANE_SHIFT_2 = 1, + ISP_LANE_SHIFT_4 = 2, + ISP_LANE_SHIFT_6 = 3, +}; + +/** + * struct isp_parallel_platform_data - Parallel interface platform data + * @data_lane_shift: Data lane shifter + * ISP_LANE_SHIFT_0 - CAMEXT[13:0] -> CAM[13:0] + * ISP_LANE_SHIFT_2 - CAMEXT[13:2] -> CAM[11:0] + * ISP_LANE_SHIFT_4 - CAMEXT[13:4] -> CAM[9:0] + * ISP_LANE_SHIFT_6 - CAMEXT[13:6] -> CAM[7:0] + * @clk_pol: Pixel clock polarity + * 0 - Non Inverted, 1 - Inverted + * @hs_pol: Horizontal synchronization polarity + * 0 - Active high, 1 - Active low + * @vs_pol: Vertical synchronization polarity + * 0 - Active high, 1 - Active low + * @bridge: CCDC Bridge input control + * ISP_BRIDGE_DISABLE - Disable + * ISP_BRIDGE_LITTLE_ENDIAN - Little endian + * ISP_BRIDGE_BIG_ENDIAN - Big endian + */ +struct isp_parallel_platform_data { + unsigned int data_lane_shift:2; + unsigned int clk_pol:1; + unsigned int hs_pol:1; + unsigned int vs_pol:1; + unsigned int bridge:2; +}; + +enum { + ISP_CCP2_PHY_DATA_CLOCK = 0, + ISP_CCP2_PHY_DATA_STROBE = 1, +}; + +enum { + ISP_CCP2_MODE_MIPI = 0, + ISP_CCP2_MODE_CCP2 = 1, +}; + +/** + * struct isp_ccp2_platform_data - CCP2 interface platform data + * @strobe_clk_pol: Strobe/clock polarity + * 0 - Non Inverted, 1 - Inverted + * @crc: Enable the cyclic redundancy check + * @ccp2_mode: Enable CCP2 compatibility mode + * ISP_CCP2_MODE_MIPI - MIPI-CSI1 mode + * ISP_CCP2_MODE_CCP2 - CCP2 mode + * @phy_layer: Physical layer selection + * ISP_CCP2_PHY_DATA_CLOCK - Data/clock physical layer + * ISP_CCP2_PHY_DATA_STROBE - Data/strobe physical layer + * @vpclk_div: Video port output clock control + */ +struct isp_ccp2_platform_data { + unsigned int strobe_clk_pol:1; + unsigned int crc:1; + unsigned int ccp2_mode:1; + unsigned int phy_layer:1; + unsigned int vpclk_div:2; +}; + +/** + * struct isp_csi2_platform_data - CSI2 interface platform data + * @crc: Enable the cyclic redundancy check + * @vpclk_div: Video port output clock control + */ +struct isp_csi2_platform_data { + unsigned crc:1; + unsigned vpclk_div:2; +}; + +struct isp_subdev_i2c_board_info { + struct i2c_board_info *board_info; + int i2c_adapter_id; +}; + +struct isp_v4l2_subdevs_group { + struct isp_subdev_i2c_board_info *subdevs; + enum isp_interface_type interface; + union { + struct isp_parallel_platform_data parallel; + struct isp_ccp2_platform_data ccp2; + struct isp_csi2_platform_data csi2; + } bus; /* gcc < 4.6.0 chokes on anonymous union initializers */ +}; + +struct isp_platform_data { + struct isp_v4l2_subdevs_group *subdevs; + void (*set_constraints)(struct isp_device *isp, bool enable); +}; + +#endif /* __MEDIA_OMAP3ISP_H__ */ diff --git a/include/media/ov772x.h b/include/media/ov772x.h index 548bf1155c8..00dbb7c4fea 100644 --- a/include/media/ov772x.h +++ b/include/media/ov772x.h @@ -12,12 +12,9 @@ #ifndef __OV772X_H__ #define __OV772X_H__ -#include <media/soc_camera.h> - /* for flags */ #define OV772X_FLAG_VFLIP (1 << 0) /* Vertical flip image */ #define OV772X_FLAG_HFLIP (1 << 1) /* Horizontal flip image */ -#define OV772X_FLAG_8BIT (1 << 2) /* default 10 bit */ /* * for Edge ctrl @@ -32,22 +29,23 @@ struct ov772x_edge_ctrl { unsigned char lower; }; -#define OV772X_MANUAL_EDGE_CTRL 0x80 /* un-used bit of strength */ -#define EDGE_STRENGTH_MASK 0x1F -#define EDGE_THRESHOLD_MASK 0x0F -#define EDGE_UPPER_MASK 0xFF -#define EDGE_LOWER_MASK 0xFF +#define OV772X_MANUAL_EDGE_CTRL 0x80 /* un-used bit of strength */ +#define OV772X_EDGE_STRENGTH_MASK 0x1F +#define OV772X_EDGE_THRESHOLD_MASK 0x0F +#define OV772X_EDGE_UPPER_MASK 0xFF +#define OV772X_EDGE_LOWER_MASK 0xFF #define OV772X_AUTO_EDGECTRL(u, l) \ { \ - .upper = (u & EDGE_UPPER_MASK), \ - .lower = (l & EDGE_LOWER_MASK), \ + .upper = (u & OV772X_EDGE_UPPER_MASK), \ + .lower = (l & OV772X_EDGE_LOWER_MASK), \ } -#define OV772X_MANUAL_EDGECTRL(s, t) \ -{ \ - .strength = (s & EDGE_STRENGTH_MASK) | OV772X_MANUAL_EDGE_CTRL,\ - .threshold = (t & EDGE_THRESHOLD_MASK), \ +#define OV772X_MANUAL_EDGECTRL(s, t) \ +{ \ + .strength = (s & OV772X_EDGE_STRENGTH_MASK) | \ + OV772X_MANUAL_EDGE_CTRL, \ + .threshold = (t & OV772X_EDGE_THRESHOLD_MASK), \ } /* diff --git a/include/media/rc-core.h b/include/media/rc-core.h index b1f19b77ecd..b0c494a6907 100644 --- a/include/media/rc-core.h +++ b/include/media/rc-core.h @@ -23,8 +23,11 @@ #include <media/rc-map.h> extern int rc_core_debug; -#define IR_dprintk(level, fmt, arg...) if (rc_core_debug >= level) \ - printk(KERN_DEBUG "%s: " fmt , __func__, ## arg) +#define IR_dprintk(level, fmt, ...) \ +do { \ + if (rc_core_debug >= level) \ + pr_debug("%s: " fmt, __func__, ##__VA_ARGS__); \ +} while (0) enum rc_driver_type { RC_DRIVER_SCANCODE = 0, /* Driver or hardware generates a scancode */ diff --git a/include/media/rc-map.h b/include/media/rc-map.h index 17c9759ae77..26a3bd0fe57 100644 --- a/include/media/rc-map.h +++ b/include/media/rc-map.h @@ -61,6 +61,7 @@ void rc_map_init(void); #define RC_MAP_APAC_VIEWCOMP "rc-apac-viewcomp" #define RC_MAP_ASUS_PC39 "rc-asus-pc39" #define RC_MAP_ATI_TV_WONDER_HD_600 "rc-ati-tv-wonder-hd-600" +#define RC_MAP_ATI_X10 "rc-ati-x10" #define RC_MAP_AVERMEDIA_A16D "rc-avermedia-a16d" #define RC_MAP_AVERMEDIA_CARDBUS "rc-avermedia-cardbus" #define RC_MAP_AVERMEDIA_DVBT "rc-avermedia-dvbt" @@ -106,6 +107,7 @@ void rc_map_init(void); #define RC_MAP_LIRC "rc-lirc" #define RC_MAP_LME2510 "rc-lme2510" #define RC_MAP_MANLI "rc-manli" +#define RC_MAP_MEDION_X10 "rc-medion-x10" #define RC_MAP_MSI_DIGIVOX_II "rc-msi-digivox-ii" #define RC_MAP_MSI_DIGIVOX_III "rc-msi-digivox-iii" #define RC_MAP_MSI_TVANYWHERE_PLUS "rc-msi-tvanywhere-plus" @@ -130,6 +132,7 @@ void rc_map_init(void); #define RC_MAP_RC5_TV "rc-rc5-tv" #define RC_MAP_RC6_MCE "rc-rc6-mce" #define RC_MAP_REAL_AUDIO_220_32_KEYS "rc-real-audio-220-32-keys" +#define RC_MAP_SNAPSTREAM_FIREFLY "rc-snapstream-firefly" #define RC_MAP_STREAMZAP "rc-streamzap" #define RC_MAP_TBS_NEC "rc-tbs-nec" #define RC_MAP_TECHNISAT_USB2 "rc-technisat-usb2" diff --git a/include/media/s5k6aa.h b/include/media/s5k6aa.h new file mode 100644 index 00000000000..ba34f7055e5 --- /dev/null +++ b/include/media/s5k6aa.h @@ -0,0 +1,51 @@ +/* + * S5K6AAFX camera sensor driver header + * + * Copyright (C) 2011 Samsung Electronics Co., Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef S5K6AA_H +#define S5K6AA_H + +#include <media/v4l2-mediabus.h> + +/** + * struct s5k6aa_gpio - data structure describing a GPIO + * @gpio: GPIO number + * @level: indicates active state of the @gpio + */ +struct s5k6aa_gpio { + int gpio; + int level; +}; + +/** + * struct s5k6aa_platform_data - s5k6aa driver platform data + * @set_power: an additional callback to the board code, called + * after enabling the regulators and before switching + * the sensor off + * @mclk_frequency: sensor's master clock frequency in Hz + * @gpio_reset: GPIO driving RESET pin + * @gpio_stby: GPIO driving STBY pin + * @nlanes: maximum number of MIPI-CSI lanes used + * @horiz_flip: default horizontal image flip value, non zero to enable + * @vert_flip: default vertical image flip value, non zero to enable + */ + +struct s5k6aa_platform_data { + int (*set_power)(int enable); + unsigned long mclk_frequency; + struct s5k6aa_gpio gpio_reset; + struct s5k6aa_gpio gpio_stby; + enum v4l2_mbus_type bus_type; + u8 nlanes; + u8 horiz_flip; + u8 vert_flip; +}; + +#endif /* S5K6AA_H */ diff --git a/include/media/s5p_fimc.h b/include/media/s5p_fimc.h index 9fdff8a4ed2..688fb3f1dc3 100644 --- a/include/media/s5p_fimc.h +++ b/include/media/s5p_fimc.h @@ -19,11 +19,6 @@ enum cam_bus_type { FIMC_LCD_WB, /* FIFO link from LCD mixer */ }; -#define FIMC_CLK_INV_PCLK (1 << 0) -#define FIMC_CLK_INV_VSYNC (1 << 1) -#define FIMC_CLK_INV_HREF (1 << 2) -#define FIMC_CLK_INV_HSYNC (1 << 3) - struct i2c_board_info; /** @@ -36,7 +31,8 @@ struct i2c_board_info; * @csi_data_align: MIPI-CSI interface data alignment in bits * @i2c_bus_num: i2c control bus id the sensor is attached to * @mux_id: FIMC camera interface multiplexer index (separate for MIPI and ITU) - * @flags: flags defining bus signals polarity inversion (High by default) + * @clk_id: index of the SoC peripheral clock for sensors + * @flags: the parallel bus flags defining signals polarity (V4L2_MBUS_*) */ struct s5p_fimc_isp_info { struct i2c_board_info *board_info; @@ -46,6 +42,7 @@ struct s5p_fimc_isp_info { u16 i2c_bus_num; u16 mux_id; u16 flags; + u8 clk_id; }; /** @@ -58,4 +55,13 @@ struct s5p_platform_fimc { struct s5p_fimc_isp_info *isp_info; int num_clients; }; + +/* + * v4l2_device notification id. This is only for internal use in the kernel. + * Sensor subdevs should issue S5P_FIMC_TX_END_NOTIFY notification in single + * frame capture mode when there is only one VSYNC pulse issued by the sensor + * at begining of the frame transmission. + */ +#define S5P_FIMC_TX_END_NOTIFY _IO('e', 0) + #endif /* S5P_FIMC_H_ */ diff --git a/include/media/saa7146.h b/include/media/saa7146.h index 79827143d5a..0f037e8edf9 100644 --- a/include/media/saa7146.h +++ b/include/media/saa7146.h @@ -1,7 +1,6 @@ #ifndef __SAA7146__ #define __SAA7146__ -#include <linux/module.h> /* for module-version */ #include <linux/delay.h> /* for delay-stuff */ #include <linux/slab.h> /* for kmalloc/kfree */ #include <linux/pci.h> /* for pci-config-stuff, vendor ids etc. */ @@ -25,28 +24,38 @@ extern unsigned int saa7146_debug; -//#define DEBUG_PROLOG printk("(0x%08x)(0x%08x) %s: %s(): ",(dev==0?-1:(dev->mem==0?-1:saa7146_read(dev,RPS_ADDR0))),(dev==0?-1:(dev->mem==0?-1:saa7146_read(dev,IER))),KBUILD_MODNAME,__func__) - #ifndef DEBUG_VARIABLE #define DEBUG_VARIABLE saa7146_debug #endif -#define DEBUG_PROLOG printk("%s: %s(): ",KBUILD_MODNAME, __func__) -#define INFO(x) { printk("%s: ",KBUILD_MODNAME); printk x; } - -#define ERR(x) { DEBUG_PROLOG; printk x; } - -#define DEB_S(x) if (0!=(DEBUG_VARIABLE&0x01)) { DEBUG_PROLOG; printk x; } /* simple debug messages */ -#define DEB_D(x) if (0!=(DEBUG_VARIABLE&0x02)) { DEBUG_PROLOG; printk x; } /* more detailed debug messages */ -#define DEB_EE(x) if (0!=(DEBUG_VARIABLE&0x04)) { DEBUG_PROLOG; printk x; } /* print enter and exit of functions */ -#define DEB_I2C(x) if (0!=(DEBUG_VARIABLE&0x08)) { DEBUG_PROLOG; printk x; } /* i2c debug messages */ -#define DEB_VBI(x) if (0!=(DEBUG_VARIABLE&0x10)) { DEBUG_PROLOG; printk x; } /* vbi debug messages */ -#define DEB_INT(x) if (0!=(DEBUG_VARIABLE&0x20)) { DEBUG_PROLOG; printk x; } /* interrupt debug messages */ -#define DEB_CAP(x) if (0!=(DEBUG_VARIABLE&0x40)) { DEBUG_PROLOG; printk x; } /* capture debug messages */ +#define ERR(fmt, ...) pr_err("%s: " fmt, __func__, ##__VA_ARGS__) + +#define _DBG(mask, fmt, ...) \ +do { \ + if (DEBUG_VARIABLE & mask) \ + pr_debug("%s(): " fmt, __func__, ##__VA_ARGS__); \ +} while (0) + +/* simple debug messages */ +#define DEB_S(fmt, ...) _DBG(0x01, fmt, ##__VA_ARGS__) +/* more detailed debug messages */ +#define DEB_D(fmt, ...) _DBG(0x02, fmt, ##__VA_ARGS__) +/* print enter and exit of functions */ +#define DEB_EE(fmt, ...) _DBG(0x04, fmt, ##__VA_ARGS__) +/* i2c debug messages */ +#define DEB_I2C(fmt, ...) _DBG(0x08, fmt, ##__VA_ARGS__) +/* vbi debug messages */ +#define DEB_VBI(fmt, ...) _DBG(0x10, fmt, ##__VA_ARGS__) +/* interrupt debug messages */ +#define DEB_INT(fmt, ...) _DBG(0x20, fmt, ##__VA_ARGS__) +/* capture debug messages */ +#define DEB_CAP(fmt, ...) _DBG(0x40, fmt, ##__VA_ARGS__) #define SAA7146_ISR_CLEAR(x,y) \ saa7146_write(x, ISR, (y)); +struct module; + struct saa7146_dev; struct saa7146_extension; struct saa7146_vv; diff --git a/include/media/soc_camera.h b/include/media/soc_camera.h index 7582952dcea..b1377b931eb 100644 --- a/include/media/soc_camera.h +++ b/include/media/soc_camera.h @@ -12,12 +12,14 @@ #ifndef SOC_CAMERA_H #define SOC_CAMERA_H +#include <linux/bitops.h> #include <linux/device.h> #include <linux/mutex.h> #include <linux/pm.h> #include <linux/videodev2.h> #include <media/videobuf-core.h> #include <media/videobuf2-core.h> +#include <media/v4l2-ctrls.h> #include <media/v4l2-device.h> struct file; @@ -37,8 +39,8 @@ struct soc_camera_device { unsigned char iface; /* Host number */ unsigned char devnum; /* Device number per host */ struct soc_camera_sense *sense; /* See comment in struct definition */ - struct soc_camera_ops *ops; struct video_device *vdev; + struct v4l2_ctrl_handler ctrl_handler; const struct soc_camera_format_xlate *current_fmt; struct soc_camera_format_xlate *user_formats; int num_user_formats; @@ -93,14 +95,10 @@ struct soc_camera_host_ops { int (*reqbufs)(struct soc_camera_device *, struct v4l2_requestbuffers *); int (*querycap)(struct soc_camera_host *, struct v4l2_capability *); int (*set_bus_param)(struct soc_camera_device *, __u32); - int (*get_ctrl)(struct soc_camera_device *, struct v4l2_control *); - int (*set_ctrl)(struct soc_camera_device *, struct v4l2_control *); int (*get_parm)(struct soc_camera_device *, struct v4l2_streamparm *); int (*set_parm)(struct soc_camera_device *, struct v4l2_streamparm *); int (*enum_fsizes)(struct soc_camera_device *, struct v4l2_frmsizeenum *); unsigned int (*poll)(struct file *, poll_table *); - const struct v4l2_queryctrl *controls; - int num_controls; }; #define SOCAM_SENSOR_INVERT_PCLK (1 << 0) @@ -193,13 +191,6 @@ struct soc_camera_format_xlate { const struct soc_mbus_pixelfmt *host_fmt; }; -struct soc_camera_ops { - unsigned long (*query_bus_param)(struct soc_camera_device *); - int (*set_bus_param)(struct soc_camera_device *, unsigned long); - const struct v4l2_queryctrl *controls; - int num_controls; -}; - #define SOCAM_SENSE_PCLK_CHANGED (1 << 0) /** @@ -226,65 +217,18 @@ struct soc_camera_sense { unsigned long pixel_clock; }; -static inline struct v4l2_queryctrl const *soc_camera_find_qctrl( - struct soc_camera_ops *ops, int id) -{ - int i; - - for (i = 0; i < ops->num_controls; i++) - if (ops->controls[i].id == id) - return &ops->controls[i]; - - return NULL; -} - -#define SOCAM_MASTER (1 << 0) -#define SOCAM_SLAVE (1 << 1) -#define SOCAM_HSYNC_ACTIVE_HIGH (1 << 2) -#define SOCAM_HSYNC_ACTIVE_LOW (1 << 3) -#define SOCAM_VSYNC_ACTIVE_HIGH (1 << 4) -#define SOCAM_VSYNC_ACTIVE_LOW (1 << 5) -#define SOCAM_DATAWIDTH_4 (1 << 6) -#define SOCAM_DATAWIDTH_8 (1 << 7) -#define SOCAM_DATAWIDTH_9 (1 << 8) -#define SOCAM_DATAWIDTH_10 (1 << 9) -#define SOCAM_DATAWIDTH_15 (1 << 10) -#define SOCAM_DATAWIDTH_16 (1 << 11) -#define SOCAM_PCLK_SAMPLE_RISING (1 << 12) -#define SOCAM_PCLK_SAMPLE_FALLING (1 << 13) -#define SOCAM_DATA_ACTIVE_HIGH (1 << 14) -#define SOCAM_DATA_ACTIVE_LOW (1 << 15) -#define SOCAM_MIPI_1LANE (1 << 16) -#define SOCAM_MIPI_2LANE (1 << 17) -#define SOCAM_MIPI_3LANE (1 << 18) -#define SOCAM_MIPI_4LANE (1 << 19) -#define SOCAM_MIPI (SOCAM_MIPI_1LANE | SOCAM_MIPI_2LANE | \ - SOCAM_MIPI_3LANE | SOCAM_MIPI_4LANE) +#define SOCAM_DATAWIDTH(x) BIT((x) - 1) +#define SOCAM_DATAWIDTH_4 SOCAM_DATAWIDTH(4) +#define SOCAM_DATAWIDTH_8 SOCAM_DATAWIDTH(8) +#define SOCAM_DATAWIDTH_9 SOCAM_DATAWIDTH(9) +#define SOCAM_DATAWIDTH_10 SOCAM_DATAWIDTH(10) +#define SOCAM_DATAWIDTH_15 SOCAM_DATAWIDTH(15) +#define SOCAM_DATAWIDTH_16 SOCAM_DATAWIDTH(16) #define SOCAM_DATAWIDTH_MASK (SOCAM_DATAWIDTH_4 | SOCAM_DATAWIDTH_8 | \ SOCAM_DATAWIDTH_9 | SOCAM_DATAWIDTH_10 | \ SOCAM_DATAWIDTH_15 | SOCAM_DATAWIDTH_16) -static inline unsigned long soc_camera_bus_param_compatible( - unsigned long camera_flags, unsigned long bus_flags) -{ - unsigned long common_flags, hsync, vsync, pclk, data, buswidth, mode; - unsigned long mipi; - - common_flags = camera_flags & bus_flags; - - hsync = common_flags & (SOCAM_HSYNC_ACTIVE_HIGH | SOCAM_HSYNC_ACTIVE_LOW); - vsync = common_flags & (SOCAM_VSYNC_ACTIVE_HIGH | SOCAM_VSYNC_ACTIVE_LOW); - pclk = common_flags & (SOCAM_PCLK_SAMPLE_RISING | SOCAM_PCLK_SAMPLE_FALLING); - data = common_flags & (SOCAM_DATA_ACTIVE_HIGH | SOCAM_DATA_ACTIVE_LOW); - mode = common_flags & (SOCAM_MASTER | SOCAM_SLAVE); - buswidth = common_flags & SOCAM_DATAWIDTH_MASK; - mipi = common_flags & SOCAM_MIPI; - - return ((!hsync || !vsync || !pclk || !data || !mode || !buswidth) && !mipi) ? 0 : - common_flags; -} - static inline void soc_camera_limit_side(int *start, int *length, unsigned int start_min, unsigned int length_min, unsigned int length_max) @@ -300,23 +244,37 @@ static inline void soc_camera_limit_side(int *start, int *length, *start = start_min + length_max - *length; } -extern unsigned long soc_camera_apply_sensor_flags(struct soc_camera_link *icl, - unsigned long flags); +unsigned long soc_camera_apply_sensor_flags(struct soc_camera_link *icl, + unsigned long flags); +unsigned long soc_camera_apply_board_flags(struct soc_camera_link *icl, + const struct v4l2_mbus_config *cfg); /* This is only temporary here - until v4l2-subdev begins to link to video_device */ #include <linux/i2c.h> -static inline struct video_device *soc_camera_i2c_to_vdev(struct i2c_client *client) +static inline struct video_device *soc_camera_i2c_to_vdev(const struct i2c_client *client) +{ + struct v4l2_subdev *sd = i2c_get_clientdata(client); + struct soc_camera_device *icd = (struct soc_camera_device *)sd->grp_id; + return icd ? icd->vdev : NULL; +} + +static inline struct soc_camera_link *soc_camera_i2c_to_link(const struct i2c_client *client) +{ + return client->dev.platform_data; +} + +static inline struct v4l2_subdev *soc_camera_vdev_to_subdev(const struct video_device *vdev) { - struct soc_camera_device *icd = client->dev.platform_data; - return icd->vdev; + struct soc_camera_device *icd = dev_get_drvdata(vdev->parent); + return soc_camera_to_subdev(icd); } -static inline struct soc_camera_device *soc_camera_from_vb2q(struct vb2_queue *vq) +static inline struct soc_camera_device *soc_camera_from_vb2q(const struct vb2_queue *vq) { return container_of(vq, struct soc_camera_device, vb2_vidq); } -static inline struct soc_camera_device *soc_camera_from_vbq(struct videobuf_queue *vq) +static inline struct soc_camera_device *soc_camera_from_vbq(const struct videobuf_queue *vq) { return container_of(vq, struct soc_camera_device, vb_vidq); } diff --git a/include/media/soc_camera_platform.h b/include/media/soc_camera_platform.h index 74f0fa15ca4..8aa4200a0b1 100644 --- a/include/media/soc_camera_platform.h +++ b/include/media/soc_camera_platform.h @@ -13,6 +13,7 @@ #include <linux/videodev2.h> #include <media/soc_camera.h> +#include <media/v4l2-mediabus.h> struct device; @@ -20,7 +21,8 @@ struct soc_camera_platform_info { const char *format_name; unsigned long format_depth; struct v4l2_mbus_framefmt format; - unsigned long bus_param; + unsigned long mbus_param; + enum v4l2_mbus_type mbus_type; struct soc_camera_device *icd; int (*set_capture)(struct soc_camera_platform_info *info, int enable); }; diff --git a/include/media/soc_mediabus.h b/include/media/soc_mediabus.h index fae432544b4..73f1e7eb60f 100644 --- a/include/media/soc_mediabus.h +++ b/include/media/soc_mediabus.h @@ -82,5 +82,7 @@ const struct soc_mbus_pixelfmt *soc_mbus_get_fmtdesc( s32 soc_mbus_bytes_per_line(u32 width, const struct soc_mbus_pixelfmt *mf); int soc_mbus_samples_per_pixel(const struct soc_mbus_pixelfmt *mf, unsigned int *numerator, unsigned int *denominator); +unsigned int soc_mbus_config_compatible(const struct v4l2_mbus_config *cfg, + unsigned int flags); #endif diff --git a/include/media/v4l2-chip-ident.h b/include/media/v4l2-chip-ident.h index 63fd9d3db29..810a20928a2 100644 --- a/include/media/v4l2-chip-ident.h +++ b/include/media/v4l2-chip-ident.h @@ -212,9 +212,6 @@ enum { /* module sn9c20x: just ident 10000 */ V4L2_IDENT_SN9C20X = 10000, - /* Siliconfile sensors: reserved range 10100 - 10199 */ - V4L2_IDENT_NOON010PC30 = 10100, - /* module cx231xx and cx25840 */ V4L2_IDENT_CX2310X_AV = 23099, /* Integrated A/V decoder; not in '100 */ V4L2_IDENT_CX23100 = 23100, diff --git a/include/media/v4l2-ctrls.h b/include/media/v4l2-ctrls.h index 13fe4d744ab..eeb3df63714 100644 --- a/include/media/v4l2-ctrls.h +++ b/include/media/v4l2-ctrls.h @@ -65,14 +65,12 @@ struct v4l2_ctrl_ops { * @is_private: If set, then this control is private to its handler and it * will not be added to any other handlers. Drivers can set * this flag. - * @is_volatile: If set, then this control is volatile. This means that the - * control's current value cannot be cached and needs to be - * retrieved through the g_volatile_ctrl op. Drivers can set - * this flag. * @is_auto: If set, then this control selects whether the other cluster * members are in 'automatic' mode or 'manual' mode. This is * used for autogain/gain type clusters. Drivers should never * set this flag directly. + * @has_volatiles: If set, then one or more members of the cluster are volatile. + * Drivers should never touch this flag. * @manual_mode_value: If the is_auto flag is set, then this is the value * of the auto control that determines if that control is in * manual mode. So if the value of the auto control equals this @@ -118,8 +116,8 @@ struct v4l2_ctrl { unsigned int is_new:1; unsigned int is_private:1; - unsigned int is_volatile:1; unsigned int is_auto:1; + unsigned int has_volatiles:1; unsigned int manual_mode_value:8; const struct v4l2_ctrl_ops *ops; @@ -208,9 +206,6 @@ struct v4l2_ctrl_handler { * must be NULL. * @is_private: If set, then this control is private to its handler and it * will not be added to any other handlers. - * @is_volatile: If set, then this control is volatile. This means that the - * control's current value cannot be cached and needs to be - * retrieved through the g_volatile_ctrl op. */ struct v4l2_ctrl_config { const struct v4l2_ctrl_ops *ops; @@ -225,7 +220,6 @@ struct v4l2_ctrl_config { u32 menu_skip_mask; const char * const *qmenu; unsigned int is_private:1; - unsigned int is_volatile:1; }; /** v4l2_ctrl_fill() - Fill in the control fields based on the control ID. @@ -389,8 +383,7 @@ void v4l2_ctrl_cluster(unsigned ncontrols, struct v4l2_ctrl **controls); * @manual_val: The value for the first control in the cluster that equals the * manual setting. * @set_volatile: If true, then all controls except the first auto control will - * have is_volatile set to true. If false, then is_volatile will not - * be touched. + * be volatile. * * Use for control groups where one control selects some automatic feature and * the other controls are only active whenever the automatic feature is turned diff --git a/include/media/v4l2-int-device.h b/include/media/v4l2-int-device.h index fbf58556157..e6aa2318367 100644 --- a/include/media/v4l2-int-device.h +++ b/include/media/v4l2-int-device.h @@ -25,7 +25,6 @@ #ifndef V4L2_INT_DEVICE_H #define V4L2_INT_DEVICE_H -#include <linux/module.h> #include <media/v4l2-common.h> #define V4L2NAMESIZE 32 @@ -41,6 +40,8 @@ enum v4l2_int_type { v4l2_int_type_slave }; +struct module; + struct v4l2_int_device; struct v4l2_int_master { diff --git a/include/media/v4l2-ioctl.h b/include/media/v4l2-ioctl.h index dd9f1e7b8ff..4d1c74ad4c8 100644 --- a/include/media/v4l2-ioctl.h +++ b/include/media/v4l2-ioctl.h @@ -122,6 +122,8 @@ struct v4l2_ioctl_ops { int (*vidioc_qbuf) (struct file *file, void *fh, struct v4l2_buffer *b); int (*vidioc_dqbuf) (struct file *file, void *fh, struct v4l2_buffer *b); + int (*vidioc_create_bufs)(struct file *file, void *fh, struct v4l2_create_buffers *b); + int (*vidioc_prepare_buf)(struct file *file, void *fh, struct v4l2_buffer *b); int (*vidioc_overlay) (struct file *file, void *fh, unsigned int i); int (*vidioc_g_fbuf) (struct file *file, void *fh, diff --git a/include/media/v4l2-mediabus.h b/include/media/v4l2-mediabus.h index 6114007c8c7..83ae07e5335 100644 --- a/include/media/v4l2-mediabus.h +++ b/include/media/v4l2-mediabus.h @@ -22,8 +22,12 @@ */ #define V4L2_MBUS_MASTER (1 << 0) #define V4L2_MBUS_SLAVE (1 << 1) -/* Which signal polarities it supports */ -/* Note: in BT.656 mode HSYNC and VSYNC are unused */ +/* + * Signal polarity flags + * Note: in BT.656 mode HSYNC, FIELD, and VSYNC are unused + * V4L2_MBUS_[HV]SYNC* flags should be also used for specifying + * configuration of hardware that uses [HV]REF signals + */ #define V4L2_MBUS_HSYNC_ACTIVE_HIGH (1 << 2) #define V4L2_MBUS_HSYNC_ACTIVE_LOW (1 << 3) #define V4L2_MBUS_VSYNC_ACTIVE_HIGH (1 << 4) @@ -32,6 +36,10 @@ #define V4L2_MBUS_PCLK_SAMPLE_FALLING (1 << 7) #define V4L2_MBUS_DATA_ACTIVE_HIGH (1 << 8) #define V4L2_MBUS_DATA_ACTIVE_LOW (1 << 9) +/* FIELD = 0/1 - Field1 (odd)/Field2 (even) */ +#define V4L2_MBUS_FIELD_EVEN_HIGH (1 << 10) +/* FIELD = 1/0 - Field1 (odd)/Field2 (even) */ +#define V4L2_MBUS_FIELD_EVEN_LOW (1 << 11) /* Serial flags */ /* How many lanes the client can use */ diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h index 257da1a30f6..f0f3358d1b1 100644 --- a/include/media/v4l2-subdev.h +++ b/include/media/v4l2-subdev.h @@ -158,6 +158,7 @@ struct v4l2_subdev_core_ops { int (*s_ext_ctrls)(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls); int (*try_ext_ctrls)(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls); int (*querymenu)(struct v4l2_subdev *sd, struct v4l2_querymenu *qm); + int (*g_std)(struct v4l2_subdev *sd, v4l2_std_id *norm); int (*s_std)(struct v4l2_subdev *sd, v4l2_std_id norm); long (*ioctl)(struct v4l2_subdev *sd, unsigned int cmd, void *arg); #ifdef CONFIG_VIDEO_ADV_DEBUG @@ -534,13 +535,13 @@ struct v4l2_subdev { void *dev_priv; void *host_priv; /* subdev device node */ - struct video_device devnode; + struct video_device *devnode; }; #define media_entity_to_v4l2_subdev(ent) \ container_of(ent, struct v4l2_subdev, entity) #define vdev_to_v4l2_subdev(vdev) \ - container_of(vdev, struct v4l2_subdev, devnode) + video_get_drvdata(vdev) /* * Used for storing subdev information per file handle diff --git a/include/media/videobuf2-core.h b/include/media/videobuf2-core.h index f87472acbc5..a15d1f1b319 100644 --- a/include/media/videobuf2-core.h +++ b/include/media/videobuf2-core.h @@ -75,7 +75,6 @@ struct vb2_mem_ops { struct vb2_plane { void *mem_priv; - int mapped:1; }; /** @@ -106,6 +105,7 @@ enum vb2_fileio_flags { /** * enum vb2_buffer_state - current video buffer state * @VB2_BUF_STATE_DEQUEUED: buffer under userspace control + * @VB2_BUF_STATE_PREPARED: buffer prepared in videobuf and by the driver * @VB2_BUF_STATE_QUEUED: buffer queued in videobuf, but not in driver * @VB2_BUF_STATE_ACTIVE: buffer queued in driver and possibly used * in a hardware operation @@ -117,6 +117,7 @@ enum vb2_fileio_flags { */ enum vb2_buffer_state { VB2_BUF_STATE_DEQUEUED, + VB2_BUF_STATE_PREPARED, VB2_BUF_STATE_QUEUED, VB2_BUF_STATE_ACTIVE, VB2_BUF_STATE_DONE, @@ -147,7 +148,6 @@ struct vb2_queue; * @done_entry: entry on the list that stores all buffers ready to * be dequeued to userspace * @planes: private per-plane information; do not change - * @num_planes_mapped: number of mapped planes; do not change */ struct vb2_buffer { struct v4l2_buffer v4l2_buf; @@ -164,19 +164,26 @@ struct vb2_buffer { struct list_head done_entry; struct vb2_plane planes[VIDEO_MAX_PLANES]; - unsigned int num_planes_mapped; }; /** * struct vb2_ops - driver-specific callbacks * - * @queue_setup: called from a VIDIOC_REQBUFS handler, before - * memory allocation; driver should return the required - * number of buffers in num_buffers, the required number - * of planes per buffer in num_planes; the size of each - * plane should be set in the sizes[] array and optional - * per-plane allocator specific context in alloc_ctxs[] - * array + * @queue_setup: called from VIDIOC_REQBUFS and VIDIOC_CREATE_BUFS + * handlers before memory allocation, or, if + * *num_planes != 0, after the allocation to verify a + * smaller number of buffers. Driver should return + * the required number of buffers in *num_buffers, the + * required number of planes per buffer in *num_planes; the + * size of each plane should be set in the sizes[] array + * and optional per-plane allocator specific context in the + * alloc_ctxs[] array. When called from VIDIOC_REQBUFS, + * fmt == NULL, the driver has to use the currently + * configured format and *num_buffers is the total number + * of buffers, that are being allocated. When called from + * VIDIOC_CREATE_BUFS, fmt != NULL and it describes the + * target frame format. In this case *num_buffers are being + * allocated additionally to q->num_buffers. * @wait_prepare: release any locks taken while calling vb2 functions; * it is called before an ioctl needs to wait for a new * buffer to arrive; required to avoid a deadlock in @@ -189,30 +196,39 @@ struct vb2_buffer { * perform additional buffer-related initialization; * initialization failure (return != 0) will prevent * queue setup from completing successfully; optional - * @buf_prepare: called every time the buffer is queued from userspace; - * drivers may perform any initialization required before - * each hardware operation in this callback; - * if an error is returned, the buffer will not be queued - * in driver; optional + * @buf_prepare: called every time the buffer is queued from userspace + * and from the VIDIOC_PREPARE_BUF ioctl; drivers may + * perform any initialization required before each hardware + * operation in this callback; if an error is returned, the + * buffer will not be queued in driver; optional * @buf_finish: called before every dequeue of the buffer back to * userspace; drivers may perform any operations required * before userspace accesses the buffer; optional * @buf_cleanup: called once before the buffer is freed; drivers may * perform any additional cleanup; optional - * @start_streaming: called once before entering 'streaming' state; enables - * driver to receive buffers over buf_queue() callback + * @start_streaming: called once to enter 'streaming' state; the driver may + * receive buffers with @buf_queue callback before + * @start_streaming is called; the driver gets the number + * of already queued buffers in count parameter; driver + * can return an error if hardware fails or not enough + * buffers has been queued, in such case all buffers that + * have been already given by the @buf_queue callback are + * invalidated. * @stop_streaming: called when 'streaming' state must be disabled; driver * should stop any DMA transactions or wait until they * finish and give back all buffers it got from buf_queue() * callback; may use vb2_wait_for_all_buffers() function * @buf_queue: passes buffer vb to the driver; driver may start * hardware operation on this buffer; driver should give - * the buffer back by calling vb2_buffer_done() function + * the buffer back by calling vb2_buffer_done() function; + * it is allways called after calling STREAMON ioctl; + * might be called before start_streaming callback if user + * pre-queued buffers before calling STREAMON */ struct vb2_ops { - int (*queue_setup)(struct vb2_queue *q, unsigned int *num_buffers, - unsigned int *num_planes, unsigned long sizes[], - void *alloc_ctxs[]); + int (*queue_setup)(struct vb2_queue *q, const struct v4l2_format *fmt, + unsigned int *num_buffers, unsigned int *num_planes, + unsigned int sizes[], void *alloc_ctxs[]); void (*wait_prepare)(struct vb2_queue *q); void (*wait_finish)(struct vb2_queue *q); @@ -222,7 +238,7 @@ struct vb2_ops { int (*buf_finish)(struct vb2_buffer *vb); void (*buf_cleanup)(struct vb2_buffer *vb); - int (*start_streaming)(struct vb2_queue *q); + int (*start_streaming)(struct vb2_queue *q, unsigned int count); int (*stop_streaming)(struct vb2_queue *q); void (*buf_queue)(struct vb2_buffer *vb); @@ -276,6 +292,7 @@ struct vb2_queue { wait_queue_head_t done_wq; void *alloc_ctx[VIDEO_MAX_PLANES]; + unsigned int plane_sizes[VIDEO_MAX_PLANES]; unsigned int streaming:1; @@ -291,6 +308,9 @@ int vb2_wait_for_all_buffers(struct vb2_queue *q); int vb2_querybuf(struct vb2_queue *q, struct v4l2_buffer *b); int vb2_reqbufs(struct vb2_queue *q, struct v4l2_requestbuffers *req); +int vb2_create_bufs(struct vb2_queue *q, struct v4l2_create_buffers *create); +int vb2_prepare_buf(struct vb2_queue *q, struct v4l2_buffer *b); + int vb2_queue_init(struct vb2_queue *q); void vb2_queue_release(struct vb2_queue *q); @@ -302,6 +322,13 @@ int vb2_streamon(struct vb2_queue *q, enum v4l2_buf_type type); int vb2_streamoff(struct vb2_queue *q, enum v4l2_buf_type type); int vb2_mmap(struct vb2_queue *q, struct vm_area_struct *vma); +#ifndef CONFIG_MMU +unsigned long vb2_get_unmapped_area(struct vb2_queue *q, + unsigned long addr, + unsigned long len, + unsigned long pgoff, + unsigned long flags); +#endif unsigned int vb2_poll(struct vb2_queue *q, struct file *file, poll_table *wait); size_t vb2_read(struct vb2_queue *q, char __user *data, size_t count, loff_t *ppos, int nonblock); diff --git a/include/media/videobuf2-dma-contig.h b/include/media/videobuf2-dma-contig.h index 7e6c68b2377..19ae1e35056 100644 --- a/include/media/videobuf2-dma-contig.h +++ b/include/media/videobuf2-dma-contig.h @@ -17,11 +17,11 @@ #include <linux/dma-mapping.h> static inline dma_addr_t -vb2_dma_contig_plane_paddr(struct vb2_buffer *vb, unsigned int plane_no) +vb2_dma_contig_plane_dma_addr(struct vb2_buffer *vb, unsigned int plane_no) { - dma_addr_t *paddr = vb2_plane_cookie(vb, plane_no); + dma_addr_t *addr = vb2_plane_cookie(vb, plane_no); - return *paddr; + return *addr; } void *vb2_dma_contig_init_ctx(struct device *dev); |