summaryrefslogtreecommitdiffstats
path: root/include/net/cfg80211.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/net/cfg80211.h')
-rw-r--r--include/net/cfg80211.h177
1 files changed, 140 insertions, 37 deletions
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 0289d4ce707..51f67a9003a 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -70,11 +70,13 @@
*
* @IEEE80211_BAND_2GHZ: 2.4GHz ISM band
* @IEEE80211_BAND_5GHZ: around 5GHz band (4.9-5.7)
+ * @IEEE80211_BAND_60GHZ: around 60 GHz band (58.32 - 64.80 GHz)
* @IEEE80211_NUM_BANDS: number of defined bands
*/
enum ieee80211_band {
IEEE80211_BAND_2GHZ = NL80211_BAND_2GHZ,
IEEE80211_BAND_5GHZ = NL80211_BAND_5GHZ,
+ IEEE80211_BAND_60GHZ = NL80211_BAND_60GHZ,
/* keep last */
IEEE80211_NUM_BANDS
@@ -211,6 +213,22 @@ struct ieee80211_sta_ht_cap {
};
/**
+ * struct ieee80211_sta_vht_cap - STA's VHT capabilities
+ *
+ * This structure describes most essential parameters needed
+ * to describe 802.11ac VHT capabilities for an STA.
+ *
+ * @vht_supported: is VHT supported by the STA
+ * @cap: VHT capabilities map as described in 802.11ac spec
+ * @vht_mcs: Supported VHT MCS rates
+ */
+struct ieee80211_sta_vht_cap {
+ bool vht_supported;
+ u32 cap; /* use IEEE80211_VHT_CAP_ */
+ struct ieee80211_vht_mcs_info vht_mcs;
+};
+
+/**
* struct ieee80211_supported_band - frequency band definition
*
* This structure describes a frequency band a wiphy
@@ -233,6 +251,7 @@ struct ieee80211_supported_band {
int n_channels;
int n_bitrates;
struct ieee80211_sta_ht_cap ht_cap;
+ struct ieee80211_sta_vht_cap vht_cap;
};
/*
@@ -404,6 +423,8 @@ struct cfg80211_beacon_data {
*
* Used to configure an AP interface.
*
+ * @channel: the channel to start the AP on
+ * @channel_type: the channel type to use
* @beacon: beacon data
* @beacon_interval: beacon interval
* @dtim_period: DTIM period
@@ -417,6 +438,9 @@ struct cfg80211_beacon_data {
* @inactivity_timeout: time in seconds to determine station's inactivity.
*/
struct cfg80211_ap_settings {
+ struct ieee80211_channel *channel;
+ enum nl80211_channel_type channel_type;
+
struct cfg80211_beacon_data beacon;
int beacon_interval, dtim_period;
@@ -556,11 +580,13 @@ enum station_info_flags {
* @RATE_INFO_FLAGS_MCS: @tx_bitrate_mcs filled
* @RATE_INFO_FLAGS_40_MHZ_WIDTH: 40 Mhz width transmission
* @RATE_INFO_FLAGS_SHORT_GI: 400ns guard interval
+ * @RATE_INFO_FLAGS_60G: 60gHz MCS
*/
enum rate_info_flags {
RATE_INFO_FLAGS_MCS = 1<<0,
RATE_INFO_FLAGS_40_MHZ_WIDTH = 1<<1,
RATE_INFO_FLAGS_SHORT_GI = 1<<2,
+ RATE_INFO_FLAGS_60G = 1<<3,
};
/**
@@ -622,10 +648,10 @@ struct sta_bss_parameters {
* @llid: mesh local link id
* @plid: mesh peer link id
* @plink_state: mesh peer link state
- * @signal: the signal strength, type depends on the wiphy's signal_type
- NOTE: For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
- * @signal_avg: avg signal strength, type depends on the wiphy's signal_type
- NOTE: For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
+ * @signal: The signal strength, type depends on the wiphy's signal_type.
+ * For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
+ * @signal_avg: Average signal strength, type depends on the wiphy's signal_type.
+ * For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
* @txrate: current unicast bitrate from this station
* @rxrate: current unicast bitrate to this station
* @rx_packets: packets received from this station
@@ -785,47 +811,101 @@ struct bss_parameters {
int ht_opmode;
};
-/*
+/**
* struct mesh_config - 802.11s mesh configuration
*
* These parameters can be changed while the mesh is active.
+ *
+ * @dot11MeshRetryTimeout: the initial retry timeout in millisecond units used
+ * by the Mesh Peering Open message
+ * @dot11MeshConfirmTimeout: the initial retry timeout in millisecond units
+ * used by the Mesh Peering Open message
+ * @dot11MeshHoldingTimeout: the confirm timeout in millisecond units used by
+ * the mesh peering management to close a mesh peering
+ * @dot11MeshMaxPeerLinks: the maximum number of peer links allowed on this
+ * mesh interface
+ * @dot11MeshMaxRetries: the maximum number of peer link open retries that can
+ * be sent to establish a new peer link instance in a mesh
+ * @dot11MeshTTL: the value of TTL field set at a source mesh STA
+ * @element_ttl: the value of TTL field set at a mesh STA for path selection
+ * elements
+ * @auto_open_plinks: whether we should automatically open peer links when we
+ * detect compatible mesh peers
+ * @dot11MeshNbrOffsetMaxNeighbor: the maximum number of neighbors to
+ * synchronize to for 11s default synchronization method
+ * @dot11MeshHWMPmaxPREQretries: the number of action frames containing a PREQ
+ * that an originator mesh STA can send to a particular path target
+ * @path_refresh_time: how frequently to refresh mesh paths in milliseconds
+ * @min_discovery_timeout: the minimum length of time to wait until giving up on
+ * a path discovery in milliseconds
+ * @dot11MeshHWMPactivePathTimeout: the time (in TUs) for which mesh STAs
+ * receiving a PREQ shall consider the forwarding information from the
+ * root to be valid. (TU = time unit)
+ * @dot11MeshHWMPpreqMinInterval: the minimum interval of time (in TUs) during
+ * which a mesh STA can send only one action frame containing a PREQ
+ * element
+ * @dot11MeshHWMPperrMinInterval: the minimum interval of time (in TUs) during
+ * which a mesh STA can send only one Action frame containing a PERR
+ * element
+ * @dot11MeshHWMPnetDiameterTraversalTime: the interval of time (in TUs) that
+ * it takes for an HWMP information element to propagate across the mesh
+ * @dot11MeshHWMPRootMode: the configuration of a mesh STA as root mesh STA
+ * @dot11MeshHWMPRannInterval: the interval of time (in TUs) between root
+ * announcements are transmitted
+ * @dot11MeshGateAnnouncementProtocol: whether to advertise that this mesh
+ * station has access to a broader network beyond the MBSS. (This is
+ * missnamed in draft 12.0: dot11MeshGateAnnouncementProtocol set to true
+ * only means that the station will announce others it's a mesh gate, but
+ * not necessarily using the gate announcement protocol. Still keeping the
+ * same nomenclature to be in sync with the spec)
+ * @dot11MeshForwarding: whether the Mesh STA is forwarding or non-forwarding
+ * entity (default is TRUE - forwarding entity)
+ * @rssi_threshold: the threshold for average signal strength of candidate
+ * station to establish a peer link
+ * @ht_opmode: mesh HT protection mode
+ *
+ * @dot11MeshHWMPactivePathToRootTimeout: The time (in TUs) for which mesh STAs
+ * receiving a proactive PREQ shall consider the forwarding information to
+ * the root mesh STA to be valid.
+ *
+ * @dot11MeshHWMProotInterval: The interval of time (in TUs) between proactive
+ * PREQs are transmitted.
+ * @dot11MeshHWMPconfirmationInterval: The minimum interval of time (in TUs)
+ * during which a mesh STA can send only one Action frame containing
+ * a PREQ element for root path confirmation.
*/
struct mesh_config {
- /* Timeouts in ms */
- /* Mesh plink management parameters */
u16 dot11MeshRetryTimeout;
u16 dot11MeshConfirmTimeout;
u16 dot11MeshHoldingTimeout;
u16 dot11MeshMaxPeerLinks;
- u8 dot11MeshMaxRetries;
- u8 dot11MeshTTL;
- /* ttl used in path selection information elements */
- u8 element_ttl;
+ u8 dot11MeshMaxRetries;
+ u8 dot11MeshTTL;
+ u8 element_ttl;
bool auto_open_plinks;
- /* neighbor offset synchronization */
u32 dot11MeshNbrOffsetMaxNeighbor;
- /* HWMP parameters */
- u8 dot11MeshHWMPmaxPREQretries;
+ u8 dot11MeshHWMPmaxPREQretries;
u32 path_refresh_time;
u16 min_discovery_timeout;
u32 dot11MeshHWMPactivePathTimeout;
u16 dot11MeshHWMPpreqMinInterval;
u16 dot11MeshHWMPperrMinInterval;
u16 dot11MeshHWMPnetDiameterTraversalTime;
- u8 dot11MeshHWMPRootMode;
+ u8 dot11MeshHWMPRootMode;
u16 dot11MeshHWMPRannInterval;
- /* This is missnamed in draft 12.0: dot11MeshGateAnnouncementProtocol
- * set to true only means that the station will announce others it's a
- * mesh gate, but not necessarily using the gate announcement protocol.
- * Still keeping the same nomenclature to be in sync with the spec. */
- bool dot11MeshGateAnnouncementProtocol;
+ bool dot11MeshGateAnnouncementProtocol;
bool dot11MeshForwarding;
s32 rssi_threshold;
u16 ht_opmode;
+ u32 dot11MeshHWMPactivePathToRootTimeout;
+ u16 dot11MeshHWMProotInterval;
+ u16 dot11MeshHWMPconfirmationInterval;
};
/**
* struct mesh_setup - 802.11s mesh setup configuration
+ * @channel: the channel to start the mesh network on
+ * @channel_type: the channel type to use
* @mesh_id: the mesh ID
* @mesh_id_len: length of the mesh ID, at least 1 and at most 32 bytes
* @sync_method: which synchronization method to use
@@ -840,6 +920,8 @@ struct mesh_config {
* These parameters are fixed when the mesh is created.
*/
struct mesh_setup {
+ struct ieee80211_channel *channel;
+ enum nl80211_channel_type channel_type;
const u8 *mesh_id;
u8 mesh_id_len;
u8 sync_method;
@@ -966,6 +1048,7 @@ struct cfg80211_match_set {
* @wiphy: the wiphy this was for
* @dev: the interface
* @channels: channels to scan
+ * @rssi_thold: don't report scan results below this threshold (in s32 dBm)
*/
struct cfg80211_sched_scan_request {
struct cfg80211_ssid *ssids;
@@ -976,6 +1059,7 @@ struct cfg80211_sched_scan_request {
size_t ie_len;
struct cfg80211_match_set *match_sets;
int n_match_sets;
+ s32 rssi_thold;
/* internal */
struct wiphy *wiphy;
@@ -1411,14 +1495,16 @@ struct cfg80211_gtk_rekey_data {
*
* @set_txq_params: Set TX queue parameters
*
- * @set_channel: Set channel for a given wireless interface. Some devices
- * may support multi-channel operation (by channel hopping) so cfg80211
- * doesn't verify much. Note, however, that the passed netdev may be
- * %NULL as well if the user requested changing the channel for the
- * device itself, or for a monitor interface.
- * @get_channel: Get the current operating channel, should return %NULL if
- * there's no single defined operating channel if for example the
- * device implements channel hopping for multi-channel virtual interfaces.
+ * @libertas_set_mesh_channel: Only for backward compatibility for libertas,
+ * as it doesn't implement join_mesh and needs to set the channel to
+ * join the mesh instead.
+ *
+ * @set_monitor_channel: Set the monitor mode channel for the device. If other
+ * interfaces are active this callback should reject the configuration.
+ * If no interfaces are active or the device is down, the channel should
+ * be stored for when a monitor interface becomes active.
+ * @set_monitor_enabled: Notify driver that there are only monitor
+ * interfaces running.
*
* @scan: Request to do a scan. If returning zero, the scan request is given
* the driver, and will be valid until passed to cfg80211_scan_done().
@@ -1605,9 +1691,13 @@ struct cfg80211_ops {
int (*set_txq_params)(struct wiphy *wiphy, struct net_device *dev,
struct ieee80211_txq_params *params);
- int (*set_channel)(struct wiphy *wiphy, struct net_device *dev,
- struct ieee80211_channel *chan,
- enum nl80211_channel_type channel_type);
+ int (*libertas_set_mesh_channel)(struct wiphy *wiphy,
+ struct net_device *dev,
+ struct ieee80211_channel *chan);
+
+ int (*set_monitor_channel)(struct wiphy *wiphy,
+ struct ieee80211_channel *chan,
+ enum nl80211_channel_type channel_type);
int (*scan)(struct wiphy *wiphy, struct net_device *dev,
struct cfg80211_scan_request *request);
@@ -1721,15 +1811,14 @@ struct cfg80211_ops {
struct net_device *dev,
u16 noack_map);
- struct ieee80211_channel *(*get_channel)(struct wiphy *wiphy,
- enum nl80211_channel_type *type);
-
int (*get_et_sset_count)(struct wiphy *wiphy,
struct net_device *dev, int sset);
void (*get_et_stats)(struct wiphy *wiphy, struct net_device *dev,
struct ethtool_stats *stats, u64 *data);
void (*get_et_strings)(struct wiphy *wiphy, struct net_device *dev,
u32 sset, u8 *data);
+
+ void (*set_monitor_enabled)(struct wiphy *wiphy, bool enabled);
};
/*
@@ -2083,7 +2172,9 @@ struct wiphy {
char fw_version[ETHTOOL_BUSINFO_LEN];
u32 hw_version;
+#ifdef CONFIG_PM
struct wiphy_wowlan_support wowlan;
+#endif
u16 max_remain_on_channel_duration;
@@ -2263,7 +2354,10 @@ struct cfg80211_cached_keys;
* @netdev: (private) Used to reference back to the netdev
* @current_bss: (private) Used by the internal configuration code
* @channel: (private) Used by the internal configuration code to track
- * user-set AP, monitor and WDS channels for wireless extensions
+ * the user-set AP, monitor and WDS channel
+ * @preset_chan: (private) Used by the internal configuration code to
+ * track the channel to be used for AP later
+ * @preset_chantype: (private) the corresponding channel type
* @bssid: (private) Used by the internal configuration code
* @ssid: (private) Used by the internal configuration code
* @ssid_len: (private) Used by the internal configuration code
@@ -2313,8 +2407,14 @@ struct wireless_dev {
spinlock_t event_lock;
struct cfg80211_internal_bss *current_bss; /* associated / joined */
+ struct ieee80211_channel *preset_chan;
+ enum nl80211_channel_type preset_chantype;
+
+ /* for AP and mesh channel tracking */
struct ieee80211_channel *channel;
+ bool ibss_fixed;
+
bool ps;
int ps_timeout;
@@ -3359,11 +3459,14 @@ void cfg80211_report_obss_beacon(struct wiphy *wiphy,
const u8 *frame, size_t len,
int freq, int sig_dbm, gfp_t gfp);
-/*
+/**
* cfg80211_can_beacon_sec_chan - test if ht40 on extension channel can be used
* @wiphy: the wiphy
* @chan: main channel
* @channel_type: HT mode
+ *
+ * This function returns true if there is no secondary channel or the secondary
+ * channel can be used for beaconing (i.e. is not a radar channel etc.)
*/
bool cfg80211_can_beacon_sec_chan(struct wiphy *wiphy,
struct ieee80211_channel *chan,
@@ -3386,7 +3489,7 @@ void cfg80211_ch_switch_notify(struct net_device *dev, int freq,
*
* return 0 if MCS index >= 32
*/
-u16 cfg80211_calculate_bitrate(struct rate_info *rate);
+u32 cfg80211_calculate_bitrate(struct rate_info *rate);
/* Logging, debugging and troubleshooting/diagnostic helpers. */
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-01-04 01:36:19 +0000