summaryrefslogtreecommitdiffstats
path: root/include/net/mac80211.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/net/mac80211.h')
-rw-r--r--include/net/mac80211.h272
1 files changed, 220 insertions, 52 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 17b60391fcd..9083bafb63c 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -139,17 +139,54 @@ enum ieee80211_phymode {
};
/**
+ * struct ieee80211_ht_info - describing STA's HT capabilities
+ *
+ * This structure describes most essential parameters needed
+ * to describe 802.11n HT capabilities for an STA.
+ *
+ * @ht_supported: is HT supported by STA, 0: no, 1: yes
+ * @cap: HT capabilities map as described in 802.11n spec
+ * @ampdu_factor: Maximum A-MPDU length factor
+ * @ampdu_density: Minimum A-MPDU spacing
+ * @supp_mcs_set: Supported MCS set as described in 802.11n spec
+ */
+struct ieee80211_ht_info {
+ u8 ht_supported;
+ u16 cap; /* use IEEE80211_HT_CAP_ */
+ u8 ampdu_factor;
+ u8 ampdu_density;
+ u8 supp_mcs_set[16];
+};
+
+/**
+ * struct ieee80211_ht_bss_info - describing BSS's HT characteristics
+ *
+ * This structure describes most essential parameters needed
+ * to describe 802.11n HT characteristics in a BSS
+ *
+ * @primary_channel: channel number of primery channel
+ * @bss_cap: 802.11n's general BSS capabilities (e.g. channel width)
+ * @bss_op_mode: 802.11n's BSS operation modes (e.g. HT protection)
+ */
+struct ieee80211_ht_bss_info {
+ u8 primary_channel;
+ u8 bss_cap; /* use IEEE80211_HT_IE_CHA_ */
+ u8 bss_op_mode; /* use IEEE80211_HT_IE_ */
+};
+
+/**
* struct ieee80211_hw_mode - PHY mode definition
*
* This structure describes the capabilities supported by the device
* in a single PHY mode.
*
+ * @list: internal
+ * @channels: pointer to array of supported channels
+ * @rates: pointer to array of supported bitrates
* @mode: the PHY mode for this definition
* @num_channels: number of supported channels
- * @channels: pointer to array of supported channels
* @num_rates: number of supported bitrates
- * @rates: pointer to array of supported bitrates
- * @list: internal
+ * @ht_info: PHY's 802.11n HT abilities for this mode
*/
struct ieee80211_hw_mode {
struct list_head list;
@@ -158,6 +195,7 @@ struct ieee80211_hw_mode {
enum ieee80211_phymode mode;
int num_channels;
int num_rates;
+ struct ieee80211_ht_info ht_info;
};
/**
@@ -237,11 +275,49 @@ struct ieee80211_low_level_stats {
unsigned int dot11RTSSuccessCount;
};
+/**
+ * enum ieee80211_bss_change - BSS change notification flags
+ *
+ * These flags are used with the bss_info_changed() callback
+ * to indicate which BSS parameter changed.
+ *
+ * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
+ * also implies a change in the AID.
+ * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
+ * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
+ */
+enum ieee80211_bss_change {
+ BSS_CHANGED_ASSOC = 1<<0,
+ BSS_CHANGED_ERP_CTS_PROT = 1<<1,
+ BSS_CHANGED_ERP_PREAMBLE = 1<<2,
+};
+
+/**
+ * struct ieee80211_bss_conf - holds the BSS's changing parameters
+ *
+ * This structure keeps information about a BSS (and an association
+ * to that BSS) that can change during the lifetime of the BSS.
+ *
+ * @assoc: association status
+ * @aid: association ID number, valid only when @assoc is true
+ * @use_cts_prot: use CTS protection
+ * @use_short_preamble: use 802.11b short preamble
+ */
+struct ieee80211_bss_conf {
+ /* association related data */
+ bool assoc;
+ u16 aid;
+ /* erp related data */
+ bool use_cts_prot;
+ bool use_short_preamble;
+};
+
/* Transmit control fields. This data structure is passed to low-level driver
* with each TX frame. The low-level driver is responsible for configuring
* the hardware to use given values (depending on what is supported). */
struct ieee80211_tx_control {
+ struct ieee80211_vif *vif;
int tx_rate; /* Transmit rate, given as the hw specific value for the
* rate (from struct ieee80211_rate) */
int rts_cts_rate; /* Transmit rate for RTS/CTS frame, given as the hw
@@ -269,6 +345,9 @@ struct ieee80211_tx_control {
* using the through
* set_retry_limit configured
* long retry value */
+#define IEEE80211_TXCTL_EAPOL_FRAME (1<<11) /* internal to mac80211 */
+#define IEEE80211_TXCTL_SEND_AFTER_DTIM (1<<12) /* send this frame after DTIM
+ * beacon */
u32 flags; /* tx control flags defined
* above */
u8 key_idx; /* keyidx from hw->set_key(), undefined if
@@ -291,7 +370,6 @@ struct ieee80211_tx_control {
* packet dropping when probing higher rates, if hw
* supports multiple retry rates. -1 = not used */
int type; /* internal */
- int ifindex; /* internal */
};
@@ -312,6 +390,8 @@ struct ieee80211_tx_control {
* the frame.
* @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
* the frame.
+ * @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field)
+ * is valid.
*/
enum mac80211_rx_flags {
RX_FLAG_MMIC_ERROR = 1<<0,
@@ -321,6 +401,7 @@ enum mac80211_rx_flags {
RX_FLAG_IV_STRIPPED = 1<<4,
RX_FLAG_FAILED_FCS_CRC = 1<<5,
RX_FLAG_FAILED_PLCP_CRC = 1<<6,
+ RX_FLAG_TSFT = 1<<7,
};
/**
@@ -406,11 +487,12 @@ struct ieee80211_tx_status {
*
* @IEEE80211_CONF_SHORT_SLOT_TIME: use 802.11g short slot time
* @IEEE80211_CONF_RADIOTAP: add radiotap header at receive time (if supported)
- *
+ * @IEEE80211_CONF_SUPPORT_HT_MODE: use 802.11n HT capabilities (if supported)
*/
enum ieee80211_conf_flags {
- IEEE80211_CONF_SHORT_SLOT_TIME = 1<<0,
- IEEE80211_CONF_RADIOTAP = 1<<1,
+ IEEE80211_CONF_SHORT_SLOT_TIME = (1<<0),
+ IEEE80211_CONF_RADIOTAP = (1<<1),
+ IEEE80211_CONF_SUPPORT_HT_MODE = (1<<2),
};
/**
@@ -434,6 +516,8 @@ enum ieee80211_conf_flags {
* @antenna_sel_tx: transmit antenna selection, 0: default/diversity,
* 1/2: antenna 0/1
* @antenna_sel_rx: receive antenna selection, like @antenna_sel_tx
+ * @ht_conf: describes current self configuration of 802.11n HT capabilies
+ * @ht_bss_conf: describes current BSS configuration of 802.11n HT parameters
*/
struct ieee80211_conf {
int channel; /* IEEE 802.11 channel number */
@@ -452,6 +536,9 @@ struct ieee80211_conf {
u8 antenna_max;
u8 antenna_sel_tx;
u8 antenna_sel_rx;
+
+ struct ieee80211_ht_info ht_conf;
+ struct ieee80211_ht_bss_info ht_bss_conf;
};
/**
@@ -480,13 +567,27 @@ enum ieee80211_if_types {
};
/**
+ * struct ieee80211_vif - per-interface data
+ *
+ * Data in this structure is continually present for driver
+ * use during the life of a virtual interface.
+ *
+ * @type: type of this virtual interface
+ * @drv_priv: data area for driver use, will always be aligned to
+ * sizeof(void *).
+ */
+struct ieee80211_vif {
+ enum ieee80211_if_types type;
+ /* must be last */
+ u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
+};
+
+/**
* struct ieee80211_if_init_conf - initial configuration of an interface
*
- * @if_id: internal interface ID. This number has no particular meaning to
- * drivers and the only allowed usage is to pass it to
- * ieee80211_beacon_get() and ieee80211_get_buffered_bc() functions.
- * This field is not valid for monitor interfaces
- * (interfaces of %IEEE80211_IF_TYPE_MNTR type).
+ * @vif: pointer to a driver-use per-interface structure. The pointer
+ * itself is also used for various functions including
+ * ieee80211_beacon_get() and ieee80211_get_buffered_bc().
* @type: one of &enum ieee80211_if_types constants. Determines the type of
* added/removed interface.
* @mac_addr: pointer to MAC address of the interface. This pointer is valid
@@ -503,8 +604,8 @@ enum ieee80211_if_types {
* in pure monitor mode.
*/
struct ieee80211_if_init_conf {
- int if_id;
enum ieee80211_if_types type;
+ struct ieee80211_vif *vif;
void *mac_addr;
};
@@ -597,9 +698,6 @@ struct ieee80211_key_conf {
u8 key[0];
};
-#define IEEE80211_SEQ_COUNTER_RX 0
-#define IEEE80211_SEQ_COUNTER_TX 1
-
/**
* enum set_key_cmd - key command
*
@@ -710,6 +808,9 @@ enum ieee80211_hw_flags {
* @rate_control_algorithm: rate control algorithm for this hardware.
* If unset (NULL), the default algorithm will be used. Must be
* set before calling ieee80211_register_hw().
+ *
+ * @vif_data_size: size (in bytes) of the drv_priv data area
+ * within &struct ieee80211_vif.
*/
struct ieee80211_hw {
struct ieee80211_conf conf;
@@ -720,6 +821,7 @@ struct ieee80211_hw {
u32 flags;
unsigned int extra_tx_headroom;
int channel_change_time;
+ int vif_data_size;
u8 queues;
s8 max_rssi;
s8 max_signal;
@@ -859,19 +961,18 @@ enum ieee80211_filter_flags {
};
/**
- * enum ieee80211_erp_change_flags - erp change flags
+ * enum ieee80211_ampdu_mlme_action - A-MPDU actions
*
- * These flags are used with the erp_ie_changed() callback in
- * &struct ieee80211_ops to indicate which parameter(s) changed.
- * @IEEE80211_ERP_CHANGE_PROTECTION: protection changed
- * @IEEE80211_ERP_CHANGE_PREAMBLE: barker preamble mode changed
+ * These flags are used with the ampdu_action() callback in
+ * &struct ieee80211_ops to indicate which action is needed.
+ * @IEEE80211_AMPDU_RX_START: start Rx aggregation
+ * @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation
*/
-enum ieee80211_erp_change_flags {
- IEEE80211_ERP_CHANGE_PROTECTION = 1<<0,
- IEEE80211_ERP_CHANGE_PREAMBLE = 1<<1,
+enum ieee80211_ampdu_mlme_action {
+ IEEE80211_AMPDU_RX_START,
+ IEEE80211_AMPDU_RX_STOP,
};
-
/**
* struct ieee80211_ops - callbacks from mac80211 to the driver
*
@@ -927,6 +1028,14 @@ enum ieee80211_erp_change_flags {
* @config_interface: Handler for configuration requests related to interfaces
* (e.g. BSSID changes.)
*
+ * @bss_info_changed: Handler for configuration requests related to BSS
+ * parameters that may vary during BSS's lifespan, and may affect low
+ * level driver (e.g. assoc/disassoc status, erp parameters).
+ * This function should not be used if no BSS has been set, unless
+ * for association indication. The @changed parameter indicates which
+ * of the bss parameters has changed when a call is made. This callback
+ * has to be atomic.
+ *
* @configure_filter: Configure the device's RX filter.
* See the section "Frame filtering" for more information.
* This callback must be implemented and atomic.
@@ -946,9 +1055,9 @@ enum ieee80211_erp_change_flags {
*
* @get_stats: return low-level statistics
*
- * @get_sequence_counter: For devices that have internal sequence counters this
- * callback allows mac80211 to access the current value of a counter.
- * This callback seems not well-defined, tell us if you need it.
+ * @get_tkip_seq: If your device implements TKIP encryption in hardware this
+ * callback should be provided to read the TKIP transmit IVs (both IV32
+ * and IV16) for the given key from hardware.
*
* @set_rts_threshold: Configuration of RTS threshold (if device needs it)
*
@@ -961,8 +1070,6 @@ enum ieee80211_erp_change_flags {
* @sta_notify: Notifies low level driver about addition or removal
* of assocaited station or AP.
*
- * @erp_ie_changed: Handle ERP IE change notifications. Must be atomic.
- *
* @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
* bursting) for a hardware TX queue. The @queue parameter uses the
* %IEEE80211_TX_QUEUE_* constants. Must be atomic.
@@ -997,6 +1104,14 @@ enum ieee80211_erp_change_flags {
* @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
* This is needed only for IBSS mode and the result of this function is
* used to determine whether to reply to Probe Requests.
+ *
+ * @conf_ht: Configures low level driver with 802.11n HT data. Must be atomic.
+ *
+ * @ampdu_action: Perform a certain A-MPDU action
+ * The RA/TID combination determines the destination and TID we want
+ * the ampdu action to be performed for. The action is defined through
+ * ieee80211_ampdu_mlme_action. Starting sequence number (@ssn)
+ * is the first frame we expect to perform the action on.
*/
struct ieee80211_ops {
int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb,
@@ -1009,7 +1124,12 @@ struct ieee80211_ops {
struct ieee80211_if_init_conf *conf);
int (*config)(struct ieee80211_hw *hw, struct ieee80211_conf *conf);
int (*config_interface)(struct ieee80211_hw *hw,
- int if_id, struct ieee80211_if_conf *conf);
+ struct ieee80211_vif *vif,
+ struct ieee80211_if_conf *conf);
+ void (*bss_info_changed)(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
+ struct ieee80211_bss_conf *info,
+ u32 changed);
void (*configure_filter)(struct ieee80211_hw *hw,
unsigned int changed_flags,
unsigned int *total_flags,
@@ -1021,17 +1141,14 @@ struct ieee80211_ops {
int (*hw_scan)(struct ieee80211_hw *hw, u8 *ssid, size_t len);
int (*get_stats)(struct ieee80211_hw *hw,
struct ieee80211_low_level_stats *stats);
- int (*get_sequence_counter)(struct ieee80211_hw *hw,
- u8* addr, u8 keyidx, u8 txrx,
- u32* iv32, u16* iv16);
+ void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx,
+ u32 *iv32, u16 *iv16);
int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);
int (*set_retry_limit)(struct ieee80211_hw *hw,
u32 short_retry, u32 long_retr);
- void (*sta_notify)(struct ieee80211_hw *hw, int if_id,
+ void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
enum sta_notify_cmd, const u8 *addr);
- void (*erp_ie_changed)(struct ieee80211_hw *hw, u8 changes,
- int cts_protection, int preamble);
int (*conf_tx)(struct ieee80211_hw *hw, int queue,
const struct ieee80211_tx_queue_params *params);
int (*get_tx_stats)(struct ieee80211_hw *hw,
@@ -1042,6 +1159,10 @@ struct ieee80211_ops {
struct sk_buff *skb,
struct ieee80211_tx_control *control);
int (*tx_last_beacon)(struct ieee80211_hw *hw);
+ int (*conf_ht)(struct ieee80211_hw *hw, struct ieee80211_conf *conf);
+ int (*ampdu_action)(struct ieee80211_hw *hw,
+ enum ieee80211_ampdu_mlme_action action,
+ const u8 *ra, u16 tid, u16 ssn);
};
/**
@@ -1073,6 +1194,7 @@ int ieee80211_register_hw(struct ieee80211_hw *hw);
extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
extern char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
+extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
#endif
/**
* ieee80211_get_tx_led_name - get name of TX LED
@@ -1112,6 +1234,16 @@ static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw)
#endif
}
+/**
+ * ieee80211_get_assoc_led_name - get name of association LED
+ *
+ * mac80211 creates a association LED trigger for each wireless hardware
+ * that can be used to drive LEDs if your driver registers a LED device.
+ * This function returns the name (or %NULL if not configured for LEDs)
+ * of the trigger so you can automatically link the LED device.
+ *
+ * @hw: the hardware to get the LED trigger name for
+ */
static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
@@ -1121,6 +1253,24 @@ static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
#endif
}
+/**
+ * ieee80211_get_radio_led_name - get name of radio LED
+ *
+ * mac80211 creates a radio change LED trigger for each wireless hardware
+ * that can be used to drive LEDs if your driver registers a LED device.
+ * This function returns the name (or %NULL if not configured for LEDs)
+ * of the trigger so you can automatically link the LED device.
+ *
+ * @hw: the hardware to get the LED trigger name for
+ */
+static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw)
+{
+#ifdef CONFIG_MAC80211_LEDS
+ return __ieee80211_get_radio_led_name(hw);
+#else
+ return NULL;
+#endif
+}
/* Register a new hardware PHYMODE capability to the stack. */
int ieee80211_register_hwmode(struct ieee80211_hw *hw,
@@ -1210,7 +1360,7 @@ void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
/**
* ieee80211_beacon_get - beacon generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @control: will be filled with information needed to send this beacon.
*
* If the beacon frames are generated by the host system (i.e., not in
@@ -1221,13 +1371,13 @@ void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
* is responsible of freeing it.
*/
struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
- int if_id,
+ struct ieee80211_vif *vif,
struct ieee80211_tx_control *control);
/**
* ieee80211_rts_get - RTS frame generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame: pointer to the frame that is going to be protected by the RTS.
* @frame_len: the frame length (in octets).
* @frame_txctl: &struct ieee80211_tx_control of the frame.
@@ -1238,7 +1388,7 @@ struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
* the next RTS frame from the 802.11 code. The low-level is responsible
* for calling this function before and RTS frame is needed.
*/
-void ieee80211_rts_get(struct ieee80211_hw *hw, int if_id,
+void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
const void *frame, size_t frame_len,
const struct ieee80211_tx_control *frame_txctl,
struct ieee80211_rts *rts);
@@ -1246,7 +1396,7 @@ void ieee80211_rts_get(struct ieee80211_hw *hw, int if_id,
/**
* ieee80211_rts_duration - Get the duration field for an RTS frame
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame_len: the length of the frame that is going to be protected by the RTS.
* @frame_txctl: &struct ieee80211_tx_control of the frame.
*
@@ -1254,14 +1404,14 @@ void ieee80211_rts_get(struct ieee80211_hw *hw, int if_id,
* the duration field, the low-level driver uses this function to receive
* the duration field value in little-endian byteorder.
*/
-__le16 ieee80211_rts_duration(struct ieee80211_hw *hw, int if_id,
- size_t frame_len,
+__le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif, size_t frame_len,
const struct ieee80211_tx_control *frame_txctl);
/**
* ieee80211_ctstoself_get - CTS-to-self frame generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame: pointer to the frame that is going to be protected by the CTS-to-self.
* @frame_len: the frame length (in octets).
* @frame_txctl: &struct ieee80211_tx_control of the frame.
@@ -1272,7 +1422,8 @@ __le16 ieee80211_rts_duration(struct ieee80211_hw *hw, int if_id,
* the next CTS-to-self frame from the 802.11 code. The low-level is responsible
* for calling this function before and CTS-to-self frame is needed.
*/
-void ieee80211_ctstoself_get(struct ieee80211_hw *hw, int if_id,
+void ieee80211_ctstoself_get(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
const void *frame, size_t frame_len,
const struct ieee80211_tx_control *frame_txctl,
struct ieee80211_cts *cts);
@@ -1280,7 +1431,7 @@ void ieee80211_ctstoself_get(struct ieee80211_hw *hw, int if_id,
/**
* ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
* @frame_txctl: &struct ieee80211_tx_control of the frame.
*
@@ -1288,28 +1439,30 @@ void ieee80211_ctstoself_get(struct ieee80211_hw *hw, int if_id,
* the duration field, the low-level driver uses this function to receive
* the duration field value in little-endian byteorder.
*/
-__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, int if_id,
+__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
size_t frame_len,
const struct ieee80211_tx_control *frame_txctl);
/**
* ieee80211_generic_frame_duration - Calculate the duration field for a frame
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame_len: the length of the frame.
* @rate: the rate (in 100kbps) at which the frame is going to be transmitted.
*
* Calculate the duration field of some generic frame, given its
* length and transmission rate (in 100kbps).
*/
-__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, int if_id,
+__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
size_t frame_len,
int rate);
/**
* ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
* @hw: pointer as obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @control: will be filled with information needed to send returned frame.
*
* Function for accessing buffered broadcast and multicast frames. If
@@ -1328,7 +1481,7 @@ __le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, int if_id,
* use common code for all beacons.
*/
struct sk_buff *
-ieee80211_get_buffered_bc(struct ieee80211_hw *hw, int if_id,
+ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
struct ieee80211_tx_control *control);
/**
@@ -1406,4 +1559,19 @@ void ieee80211_wake_queues(struct ieee80211_hw *hw);
*/
void ieee80211_scan_completed(struct ieee80211_hw *hw);
+/**
+ * ieee80211_iterate_active_interfaces - iterate active interfaces
+ *
+ * This function iterates over the interfaces associated with a given
+ * hardware that are currently active and calls the callback for them.
+ *
+ * @hw: the hardware struct of which the interfaces should be iterated over
+ * @iterator: the iterator function to call, cannot sleep
+ * @data: first argument of the iterator function
+ */
+void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw,
+ void (*iterator)(void *data, u8 *mac,
+ struct ieee80211_vif *vif),
+ void *data);
+
#endif /* MAC80211_H */