diff options
Diffstat (limited to 'include')
179 files changed, 6915 insertions, 3460 deletions
diff --git a/include/acpi/acconfig.h b/include/acpi/acconfig.h new file mode 100644 index 00000000000..03f14856bd0 --- /dev/null +++ b/include/acpi/acconfig.h @@ -0,0 +1,248 @@ +/****************************************************************************** + * + * Name: acconfig.h - Global configuration constants + * + *****************************************************************************/ + +/* + * Copyright (C) 2000 - 2012, Intel Corp. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + */ + +#ifndef _ACCONFIG_H +#define _ACCONFIG_H + +/****************************************************************************** + * + * Configuration options + * + *****************************************************************************/ + +/* + * ACPI_DEBUG_OUTPUT - This switch enables all the debug facilities of the + * ACPI subsystem. This includes the DEBUG_PRINT output + * statements. When disabled, all DEBUG_PRINT + * statements are compiled out. + * + * ACPI_APPLICATION - Use this switch if the subsystem is going to be run + * at the application level. + * + */ + +/* + * OS name, used for the _OS object. The _OS object is essentially obsolete, + * but there is a large base of ASL/AML code in existing machines that check + * for the string below. The use of this string usually guarantees that + * the ASL will execute down the most tested code path. Also, there is some + * code that will not execute the _OSI method unless _OS matches the string + * below. Therefore, change this string at your own risk. + */ +#define ACPI_OS_NAME "Microsoft Windows NT" + +/* Maximum objects in the various object caches */ + +#define ACPI_MAX_STATE_CACHE_DEPTH 96 /* State objects */ +#define ACPI_MAX_PARSE_CACHE_DEPTH 96 /* Parse tree objects */ +#define ACPI_MAX_EXTPARSE_CACHE_DEPTH 96 /* Parse tree objects */ +#define ACPI_MAX_OBJECT_CACHE_DEPTH 96 /* Interpreter operand objects */ +#define ACPI_MAX_NAMESPACE_CACHE_DEPTH 96 /* Namespace objects */ + +/* + * Should the subsystem abort the loading of an ACPI table if the + * table checksum is incorrect? + */ +#define ACPI_CHECKSUM_ABORT FALSE + +/* + * Generate a version of ACPICA that only supports "reduced hardware" + * platforms (as defined in ACPI 5.0). Set to TRUE to generate a specialized + * version of ACPICA that ONLY supports the ACPI 5.0 "reduced hardware" + * model. In other words, no ACPI hardware is supported. + * + * If TRUE, this means no support for the following: + * PM Event and Control registers + * SCI interrupt (and handler) + * Fixed Events + * General Purpose Events (GPEs) + * Global Lock + * ACPI PM timer + * FACS table (Waking vectors and Global Lock) + */ +#define ACPI_REDUCED_HARDWARE FALSE + +/****************************************************************************** + * + * Subsystem Constants + * + *****************************************************************************/ + +/* Version of ACPI supported */ + +#define ACPI_CA_SUPPORT_LEVEL 5 + +/* Maximum count for a semaphore object */ + +#define ACPI_MAX_SEMAPHORE_COUNT 256 + +/* Maximum object reference count (detects object deletion issues) */ + +#define ACPI_MAX_REFERENCE_COUNT 0x1000 + +/* Default page size for use in mapping memory for operation regions */ + +#define ACPI_DEFAULT_PAGE_SIZE 4096 /* Must be power of 2 */ + +/* owner_id tracking. 8 entries allows for 255 owner_ids */ + +#define ACPI_NUM_OWNERID_MASKS 8 + +/* Size of the root table array is increased by this increment */ + +#define ACPI_ROOT_TABLE_SIZE_INCREMENT 4 + +/* Maximum number of While() loop iterations before forced abort */ + +#define ACPI_MAX_LOOP_ITERATIONS 0xFFFF + +/* Maximum sleep allowed via Sleep() operator */ + +#define ACPI_MAX_SLEEP 2000 /* Two seconds */ + +/* Address Range lists are per-space_id (Memory and I/O only) */ + +#define ACPI_ADDRESS_RANGE_MAX 2 + +/****************************************************************************** + * + * ACPI Specification constants (Do not change unless the specification changes) + * + *****************************************************************************/ + +/* Number of distinct GPE register blocks and register width */ + +#define ACPI_MAX_GPE_BLOCKS 2 +#define ACPI_GPE_REGISTER_WIDTH 8 + +/* Method info (in WALK_STATE), containing local variables and argumetns */ + +#define ACPI_METHOD_NUM_LOCALS 8 +#define ACPI_METHOD_MAX_LOCAL 7 + +#define ACPI_METHOD_NUM_ARGS 7 +#define ACPI_METHOD_MAX_ARG 6 + +/* Length of _HID, _UID, _CID, and UUID values */ + +#define ACPI_DEVICE_ID_LENGTH 0x09 +#define ACPI_MAX_CID_LENGTH 48 +#define ACPI_UUID_LENGTH 16 + +/* + * Operand Stack (in WALK_STATE), Must be large enough to contain METHOD_MAX_ARG + */ +#define ACPI_OBJ_NUM_OPERANDS 8 +#define ACPI_OBJ_MAX_OPERAND 7 + +/* Number of elements in the Result Stack frame, can be an arbitrary value */ + +#define ACPI_RESULTS_FRAME_OBJ_NUM 8 + +/* + * Maximal number of elements the Result Stack can contain, + * it may be an arbitray value not exceeding the types of + * result_size and result_count (now u8). + */ +#define ACPI_RESULTS_OBJ_NUM_MAX 255 + +/* Names within the namespace are 4 bytes long */ + +#define ACPI_NAME_SIZE 4 +#define ACPI_PATH_SEGMENT_LENGTH 5 /* 4 chars for name + 1 char for separator */ +#define ACPI_PATH_SEPARATOR '.' + +/* Sizes for ACPI table headers */ + +#define ACPI_OEM_ID_SIZE 6 +#define ACPI_OEM_TABLE_ID_SIZE 8 + +/* Constants used in searching for the RSDP in low memory */ + +#define ACPI_EBDA_PTR_LOCATION 0x0000040E /* Physical Address */ +#define ACPI_EBDA_PTR_LENGTH 2 +#define ACPI_EBDA_WINDOW_SIZE 1024 +#define ACPI_HI_RSDP_WINDOW_BASE 0x000E0000 /* Physical Address */ +#define ACPI_HI_RSDP_WINDOW_SIZE 0x00020000 +#define ACPI_RSDP_SCAN_STEP 16 + +/* Operation regions */ + +#define ACPI_USER_REGION_BEGIN 0x80 + +/* Maximum space_ids for Operation Regions */ + +#define ACPI_MAX_ADDRESS_SPACE 255 + +/* Array sizes. Used for range checking also */ + +#define ACPI_MAX_MATCH_OPCODE 5 + +/* RSDP checksums */ + +#define ACPI_RSDP_CHECKSUM_LENGTH 20 +#define ACPI_RSDP_XCHECKSUM_LENGTH 36 + +/* SMBus, GSBus and IPMI bidirectional buffer size */ + +#define ACPI_SMBUS_BUFFER_SIZE 34 +#define ACPI_GSBUS_BUFFER_SIZE 34 +#define ACPI_IPMI_BUFFER_SIZE 66 + +/* _sx_d and _sx_w control methods */ + +#define ACPI_NUM_sx_d_METHODS 4 +#define ACPI_NUM_sx_w_METHODS 5 + +/****************************************************************************** + * + * ACPI AML Debugger + * + *****************************************************************************/ + +#define ACPI_DEBUGGER_MAX_ARGS 8 /* Must be max method args + 1 */ + +#define ACPI_DEBUGGER_COMMAND_PROMPT '-' +#define ACPI_DEBUGGER_EXECUTE_PROMPT '%' + +#endif /* _ACCONFIG_H */ diff --git a/include/acpi/acexcep.h b/include/acpi/acexcep.h index 5b6c391efc8..92d6e1d701f 100644 --- a/include/acpi/acexcep.h +++ b/include/acpi/acexcep.h @@ -57,6 +57,7 @@ #define ACPI_SUCCESS(a) (!(a)) #define ACPI_FAILURE(a) (a) +#define ACPI_SKIP(a) (a == AE_CTRL_SKIP) #define AE_OK (acpi_status) 0x0000 /* @@ -89,8 +90,9 @@ #define AE_SAME_HANDLER (acpi_status) (0x0019 | AE_CODE_ENVIRONMENTAL) #define AE_NO_HANDLER (acpi_status) (0x001A | AE_CODE_ENVIRONMENTAL) #define AE_OWNER_ID_LIMIT (acpi_status) (0x001B | AE_CODE_ENVIRONMENTAL) +#define AE_NOT_CONFIGURED (acpi_status) (0x001C | AE_CODE_ENVIRONMENTAL) -#define AE_CODE_ENV_MAX 0x001B +#define AE_CODE_ENV_MAX 0x001C /* * Programmer exceptions @@ -213,7 +215,8 @@ char const *acpi_gbl_exception_names_env[] = { "AE_ABORT_METHOD", "AE_SAME_HANDLER", "AE_NO_HANDLER", - "AE_OWNER_ID_LIMIT" + "AE_OWNER_ID_LIMIT", + "AE_NOT_CONFIGURED" }; char const *acpi_gbl_exception_names_pgm[] = { diff --git a/include/acpi/acnames.h b/include/acpi/acnames.h index 5b5af0d30a9..38f508816e4 100644 --- a/include/acpi/acnames.h +++ b/include/acpi/acnames.h @@ -46,6 +46,7 @@ /* Method names - these methods can appear anywhere in the namespace */ +#define METHOD_NAME__SB_ "_SB_" #define METHOD_NAME__HID "_HID" #define METHOD_NAME__CID "_CID" #define METHOD_NAME__UID "_UID" @@ -64,11 +65,11 @@ /* Method names - these methods must appear at the namespace root */ -#define METHOD_NAME__BFS "\\_BFS" -#define METHOD_NAME__GTS "\\_GTS" -#define METHOD_NAME__PTS "\\_PTS" -#define METHOD_NAME__SST "\\_SI._SST" -#define METHOD_NAME__WAK "\\_WAK" +#define METHOD_PATHNAME__BFS "\\_BFS" +#define METHOD_PATHNAME__GTS "\\_GTS" +#define METHOD_PATHNAME__PTS "\\_PTS" +#define METHOD_PATHNAME__SST "\\_SI._SST" +#define METHOD_PATHNAME__WAK "\\_WAK" /* Definitions of the predefined namespace names */ @@ -79,6 +80,5 @@ #define ACPI_PREFIX_LOWER (u32) 0x69706361 /* "acpi" */ #define ACPI_NS_ROOT_PATH "\\" -#define ACPI_NS_SYSTEM_BUS "_SB_" #endif /* __ACNAMES_H__ */ diff --git a/include/acpi/acpi_bus.h b/include/acpi/acpi_bus.h index 6cd5b6403a7..f1c8ca60e82 100644 --- a/include/acpi/acpi_bus.h +++ b/include/acpi/acpi_bus.h @@ -323,6 +323,8 @@ int acpi_bus_set_power(acpi_handle handle, int state); int acpi_bus_update_power(acpi_handle handle, int *state_p); bool acpi_bus_power_manageable(acpi_handle handle); bool acpi_bus_can_wakeup(acpi_handle handle); +int acpi_power_resource_register_device(struct device *dev, acpi_handle handle); +void acpi_power_resource_unregister_device(struct device *dev, acpi_handle handle); #ifdef CONFIG_ACPI_PROC_EVENT int acpi_bus_generate_proc_event(struct acpi_device *device, u8 type, int data); int acpi_bus_generate_proc_event4(const char *class, const char *bid, u8 type, int data); @@ -392,8 +394,13 @@ static inline int acpi_pm_device_sleep_state(struct device *d, int *p) #endif #ifdef CONFIG_PM_SLEEP +int acpi_pm_device_run_wake(struct device *, bool); int acpi_pm_device_sleep_wake(struct device *, bool); #else +static inline int acpi_pm_device_run_wake(struct device *dev, bool enable) +{ + return -ENODEV; +} static inline int acpi_pm_device_sleep_wake(struct device *dev, bool enable) { return -ENODEV; diff --git a/include/acpi/acpiosxf.h b/include/acpi/acpiosxf.h index 7c9aebe8a7a..21a5548c668 100644 --- a/include/acpi/acpiosxf.h +++ b/include/acpi/acpiosxf.h @@ -95,6 +95,11 @@ acpi_status acpi_os_table_override(struct acpi_table_header *existing_table, struct acpi_table_header **new_table); +acpi_status +acpi_os_physical_table_override(struct acpi_table_header *existing_table, + acpi_physical_address * new_address, + u32 *new_table_length); + /* * Spinlock primitives */ @@ -217,14 +222,10 @@ acpi_status acpi_os_write_port(acpi_io_address address, u32 value, u32 width); * Platform and hardware-independent physical memory interfaces */ acpi_status -acpi_os_read_memory(acpi_physical_address address, u32 * value, u32 width); -acpi_status -acpi_os_read_memory64(acpi_physical_address address, u64 *value, u32 width); +acpi_os_read_memory(acpi_physical_address address, u64 *value, u32 width); acpi_status -acpi_os_write_memory(acpi_physical_address address, u32 value, u32 width); -acpi_status -acpi_os_write_memory64(acpi_physical_address address, u64 value, u32 width); +acpi_os_write_memory(acpi_physical_address address, u64 value, u32 width); /* * Platform and hardware-independent PCI configuration space access diff --git a/include/acpi/acpixf.h b/include/acpi/acpixf.h index a28da35ba45..98211013467 100644 --- a/include/acpi/acpixf.h +++ b/include/acpi/acpixf.h @@ -47,8 +47,9 @@ /* Current ACPICA subsystem version in YYYYMMDD format */ -#define ACPI_CA_VERSION 0x20120111 +#define ACPI_CA_VERSION 0x20120320 +#include "acconfig.h" #include "actypes.h" #include "actbl.h" @@ -71,6 +72,33 @@ extern u8 acpi_gbl_copy_dsdt_locally; extern u8 acpi_gbl_truncate_io_addresses; extern u8 acpi_gbl_disable_auto_repair; +/* + * Hardware-reduced prototypes. All interfaces that use these macros will + * be configured out of the ACPICA build if the ACPI_REDUCED_HARDWARE flag + * is set to TRUE. + */ +#if (!ACPI_REDUCED_HARDWARE) +#define ACPI_HW_DEPENDENT_RETURN_STATUS(prototype) \ + prototype; + +#define ACPI_HW_DEPENDENT_RETURN_OK(prototype) \ + prototype; + +#define ACPI_HW_DEPENDENT_RETURN_VOID(prototype) \ + prototype; + +#else +#define ACPI_HW_DEPENDENT_RETURN_STATUS(prototype) \ + static ACPI_INLINE prototype {return(AE_NOT_CONFIGURED);} + +#define ACPI_HW_DEPENDENT_RETURN_OK(prototype) \ + static ACPI_INLINE prototype {return(AE_OK);} + +#define ACPI_HW_DEPENDENT_RETURN_VOID(prototype) \ + static ACPI_INLINE prototype {} + +#endif /* !ACPI_REDUCED_HARDWARE */ + extern u32 acpi_current_gpe_count; extern struct acpi_table_fadt acpi_gbl_FADT; extern u8 acpi_gbl_system_awake_and_running; @@ -96,9 +124,8 @@ acpi_status acpi_terminate(void); acpi_status acpi_subsystem_status(void); #endif -acpi_status acpi_enable(void); - -acpi_status acpi_disable(void); +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status acpi_enable(void)) +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status acpi_disable(void)) #ifdef ACPI_FUTURE_USAGE acpi_status acpi_get_system_info(struct acpi_buffer *ret_buffer); @@ -235,17 +262,34 @@ acpi_status acpi_get_parent(acpi_handle object, acpi_handle * out_handle); acpi_status acpi_install_initialization_handler(acpi_init_handler handler, u32 function); -acpi_status -acpi_install_global_event_handler(ACPI_GBL_EVENT_HANDLER handler, - void *context); - -acpi_status -acpi_install_fixed_event_handler(u32 acpi_event, - acpi_event_handler handler, void *context); - -acpi_status -acpi_remove_fixed_event_handler(u32 acpi_event, acpi_event_handler handler); - +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_install_global_event_handler + (ACPI_GBL_EVENT_HANDLER handler, void *context)) + +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_install_fixed_event_handler(u32 + acpi_event, + acpi_event_handler + handler, + void + *context)) +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_remove_fixed_event_handler(u32 acpi_event, + acpi_event_handler + handler)) +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_install_gpe_handler(acpi_handle + gpe_device, + u32 gpe_number, + u32 type, + acpi_gpe_handler + address, + void *context)) +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_remove_gpe_handler(acpi_handle gpe_device, + u32 gpe_number, + acpi_gpe_handler + address)) acpi_status acpi_install_notify_handler(acpi_handle device, u32 handler_type, @@ -266,15 +310,6 @@ acpi_remove_address_space_handler(acpi_handle device, acpi_adr_space_type space_id, acpi_adr_space_handler handler); -acpi_status -acpi_install_gpe_handler(acpi_handle gpe_device, - u32 gpe_number, - u32 type, acpi_gpe_handler address, void *context); - -acpi_status -acpi_remove_gpe_handler(acpi_handle gpe_device, - u32 gpe_number, acpi_gpe_handler address); - #ifdef ACPI_FUTURE_USAGE acpi_status acpi_install_exception_handler(acpi_exception_handler handler); #endif @@ -284,9 +319,11 @@ acpi_status acpi_install_interface_handler(acpi_interface_handler handler); /* * Global Lock interfaces */ -acpi_status acpi_acquire_global_lock(u16 timeout, u32 * handle); - -acpi_status acpi_release_global_lock(u32 handle); +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_acquire_global_lock(u16 timeout, + u32 *handle)) +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_release_global_lock(u32 handle)) /* * Interfaces to AML mutex objects @@ -299,47 +336,75 @@ acpi_status acpi_release_mutex(acpi_handle handle, acpi_string pathname); /* * Fixed Event interfaces */ -acpi_status acpi_enable_event(u32 event, u32 flags); - -acpi_status acpi_disable_event(u32 event, u32 flags); +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_enable_event(u32 event, u32 flags)) -acpi_status acpi_clear_event(u32 event); +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_disable_event(u32 event, u32 flags)) -acpi_status acpi_get_event_status(u32 event, acpi_event_status * event_status); +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status acpi_clear_event(u32 event)) +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_get_event_status(u32 event, + acpi_event_status + *event_status)) /* * General Purpose Event (GPE) Interfaces */ -acpi_status acpi_enable_gpe(acpi_handle gpe_device, u32 gpe_number); - -acpi_status acpi_disable_gpe(acpi_handle gpe_device, u32 gpe_number); - -acpi_status acpi_clear_gpe(acpi_handle gpe_device, u32 gpe_number); - -acpi_status -acpi_setup_gpe_for_wake(acpi_handle parent_device, - acpi_handle gpe_device, u32 gpe_number); - -acpi_status acpi_set_gpe_wake_mask(acpi_handle gpe_device, u32 gpe_number, u8 action); - -acpi_status -acpi_get_gpe_status(acpi_handle gpe_device, - u32 gpe_number, acpi_event_status *event_status); - -acpi_status acpi_disable_all_gpes(void); - -acpi_status acpi_enable_all_runtime_gpes(void); - -acpi_status acpi_get_gpe_device(u32 gpe_index, acpi_handle *gpe_device); - -acpi_status -acpi_install_gpe_block(acpi_handle gpe_device, - struct acpi_generic_address *gpe_block_address, - u32 register_count, u32 interrupt_number); - -acpi_status acpi_remove_gpe_block(acpi_handle gpe_device); - -acpi_status acpi_update_all_gpes(void); +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status acpi_update_all_gpes(void)) + +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_enable_gpe(acpi_handle gpe_device, + u32 gpe_number)) + +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_disable_gpe(acpi_handle gpe_device, + u32 gpe_number)) + +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_clear_gpe(acpi_handle gpe_device, + u32 gpe_number)) + +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_set_gpe(acpi_handle gpe_device, + u32 gpe_number, u8 action)) + +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_finish_gpe(acpi_handle gpe_device, + u32 gpe_number)) + +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_setup_gpe_for_wake(acpi_handle + parent_device, + acpi_handle gpe_device, + u32 gpe_number)) +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_set_gpe_wake_mask(acpi_handle gpe_device, + u32 gpe_number, + u8 action)) +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_get_gpe_status(acpi_handle gpe_device, + u32 gpe_number, + acpi_event_status + *event_status)) + +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status acpi_disable_all_gpes(void)) + +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status acpi_enable_all_runtime_gpes(void)) + +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_get_gpe_device(u32 gpe_index, + acpi_handle * gpe_device)) + +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_install_gpe_block(acpi_handle gpe_device, + struct + acpi_generic_address + *gpe_block_address, + u32 register_count, + u32 interrupt_number)) +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_remove_gpe_block(acpi_handle gpe_device)) /* * Resource interfaces @@ -391,34 +456,60 @@ acpi_buffer_to_resource(u8 *aml_buffer, */ acpi_status acpi_reset(void); -acpi_status acpi_read_bit_register(u32 register_id, u32 *return_value); +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_read_bit_register(u32 register_id, + u32 *return_value)) -acpi_status acpi_write_bit_register(u32 register_id, u32 value); +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_write_bit_register(u32 register_id, + u32 value)) -acpi_status acpi_set_firmware_waking_vector(u32 physical_address); +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_set_firmware_waking_vector(u32 + physical_address)) #if ACPI_MACHINE_WIDTH == 64 -acpi_status acpi_set_firmware_waking_vector64(u64 physical_address); +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_set_firmware_waking_vector64(u64 + physical_address)) #endif acpi_status acpi_read(u64 *value, struct acpi_generic_address *reg); acpi_status acpi_write(u64 value, struct acpi_generic_address *reg); +/* + * Sleep/Wake interfaces + */ acpi_status acpi_get_sleep_type_data(u8 sleep_state, u8 * slp_typ_a, u8 * slp_typ_b); acpi_status acpi_enter_sleep_state_prep(u8 sleep_state); -acpi_status asmlinkage acpi_enter_sleep_state(u8 sleep_state); +acpi_status asmlinkage acpi_enter_sleep_state(u8 sleep_state, u8 flags); -acpi_status asmlinkage acpi_enter_sleep_state_s4bios(void); +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status asmlinkage acpi_enter_sleep_state_s4bios(void)) -acpi_status acpi_leave_sleep_state_prep(u8 sleep_state); +acpi_status acpi_leave_sleep_state_prep(u8 sleep_state, u8 flags); acpi_status acpi_leave_sleep_state(u8 sleep_state); /* + * ACPI Timer interfaces + */ +#ifdef ACPI_FUTURE_USAGE +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_get_timer_resolution(u32 *resolution)) + +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status acpi_get_timer(u32 *ticks)) + +ACPI_HW_DEPENDENT_RETURN_STATUS(acpi_status + acpi_get_timer_duration(u32 start_ticks, + u32 end_ticks, + u32 *time_elapsed)) +#endif /* ACPI_FUTURE_USAGE */ + +/* * Error/Warning output */ void ACPI_INTERNAL_VAR_XFACE diff --git a/include/acpi/actbl.h b/include/acpi/actbl.h index 8e1b92f6f65..8dea54665dc 100644 --- a/include/acpi/actbl.h +++ b/include/acpi/actbl.h @@ -309,6 +309,13 @@ enum acpi_prefered_pm_profiles { PM_TABLET = 8 }; +/* Values for sleep_status and sleep_control registers (V5 FADT) */ + +#define ACPI_X_WAKE_STATUS 0x80 +#define ACPI_X_SLEEP_TYPE_MASK 0x1C +#define ACPI_X_SLEEP_TYPE_POSITION 0x02 +#define ACPI_X_SLEEP_ENABLE 0x20 + /* Reset to default packing */ #pragma pack() diff --git a/include/acpi/actypes.h b/include/acpi/actypes.h index d5dee7ce947..eba66043cf1 100644 --- a/include/acpi/actypes.h +++ b/include/acpi/actypes.h @@ -518,6 +518,13 @@ typedef u64 acpi_integer; #define ACPI_SLEEP_TYPE_INVALID 0xFF /* + * Sleep/Wake flags + */ +#define ACPI_NO_OPTIONAL_METHODS 0x00 /* Do not execute any optional methods */ +#define ACPI_EXECUTE_GTS 0x01 /* For enter sleep interface */ +#define ACPI_EXECUTE_BFS 0x02 /* For leave sleep prep interface */ + +/* * Standard notify values */ #define ACPI_NOTIFY_BUS_CHECK (u8) 0x00 @@ -532,8 +539,9 @@ typedef u64 acpi_integer; #define ACPI_NOTIFY_DEVICE_PLD_CHECK (u8) 0x09 #define ACPI_NOTIFY_RESERVED (u8) 0x0A #define ACPI_NOTIFY_LOCALITY_UPDATE (u8) 0x0B +#define ACPI_NOTIFY_SHUTDOWN_REQUEST (u8) 0x0C -#define ACPI_NOTIFY_MAX 0x0B +#define ACPI_NOTIFY_MAX 0x0C /* * Types associated with ACPI names and objects. The first group of @@ -698,7 +706,8 @@ typedef u32 acpi_event_status; #define ACPI_ALL_NOTIFY (ACPI_SYSTEM_NOTIFY | ACPI_DEVICE_NOTIFY) #define ACPI_MAX_NOTIFY_HANDLER_TYPE 0x3 -#define ACPI_MAX_SYS_NOTIFY 0x7f +#define ACPI_MAX_SYS_NOTIFY 0x7F +#define ACPI_MAX_DEVICE_SPECIFIC_NOTIFY 0xBF /* Address Space (Operation Region) Types */ @@ -786,6 +795,15 @@ typedef u8 acpi_adr_space_type; #define ACPI_ENABLE_EVENT 1 #define ACPI_DISABLE_EVENT 0 +/* Sleep function dispatch */ + +typedef acpi_status(*ACPI_SLEEP_FUNCTION) (u8 sleep_state, u8 flags); + +struct acpi_sleep_functions { + ACPI_SLEEP_FUNCTION legacy_function; + ACPI_SLEEP_FUNCTION extended_function; +}; + /* * External ACPI object definition */ diff --git a/include/acpi/platform/aclinux.h b/include/acpi/platform/aclinux.h index f4b2effe033..6fbc4cab583 100644 --- a/include/acpi/platform/aclinux.h +++ b/include/acpi/platform/aclinux.h @@ -57,7 +57,6 @@ #include <linux/kernel.h> #include <linux/ctype.h> #include <linux/sched.h> -#include <asm/system.h> #include <linux/atomic.h> #include <asm/div64.h> #include <asm/acpi.h> diff --git a/include/asm-generic/atomic.h b/include/asm-generic/atomic.h index e37963c1df4..1ced6413ea0 100644 --- a/include/asm-generic/atomic.h +++ b/include/asm-generic/atomic.h @@ -15,6 +15,8 @@ #ifndef __ASM_GENERIC_ATOMIC_H #define __ASM_GENERIC_ATOMIC_H +#include <asm/cmpxchg.h> + #ifdef CONFIG_SMP /* Force people to define core atomics */ # if !defined(atomic_add_return) || !defined(atomic_sub_return) || \ @@ -52,7 +54,6 @@ #define atomic_set(v, i) (((v)->counter) = (i)) #include <linux/irqflags.h> -#include <asm/system.h> /** * atomic_add_return - add integer to atomic variable diff --git a/include/asm-generic/barrier.h b/include/asm-generic/barrier.h new file mode 100644 index 00000000000..639d7a4d033 --- /dev/null +++ b/include/asm-generic/barrier.h @@ -0,0 +1,50 @@ +/* Generic barrier definitions, based on MN10300 definitions. + * + * It should be possible to use these on really simple architectures, + * but it serves more as a starting point for new ports. + * + * Copyright (C) 2007 Red Hat, Inc. All Rights Reserved. + * Written by David Howells (dhowells@redhat.com) + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public Licence + * as published by the Free Software Foundation; either version + * 2 of the Licence, or (at your option) any later version. + */ +#ifndef __ASM_GENERIC_BARRIER_H +#define __ASM_GENERIC_BARRIER_H + +#ifndef __ASSEMBLY__ + +#define nop() asm volatile ("nop") + +/* + * Force strict CPU ordering. + * And yes, this is required on UP too when we're talking + * to devices. + * + * This implementation only contains a compiler barrier. + */ + +#define mb() asm volatile ("": : :"memory") +#define rmb() mb() +#define wmb() asm volatile ("": : :"memory") + +#ifdef CONFIG_SMP +#define smp_mb() mb() +#define smp_rmb() rmb() +#define smp_wmb() wmb() +#else +#define smp_mb() barrier() +#define smp_rmb() barrier() +#define smp_wmb() barrier() +#endif + +#define set_mb(var, value) do { var = value; mb(); } while (0) +#define set_wmb(var, value) do { var = value; wmb(); } while (0) + +#define read_barrier_depends() do {} while (0) +#define smp_read_barrier_depends() do {} while (0) + +#endif /* !__ASSEMBLY__ */ +#endif /* __ASM_GENERIC_BARRIER_H */ diff --git a/include/asm-generic/bitops/atomic.h b/include/asm-generic/bitops/atomic.h index ecc44a8e2b4..9ae6c34dc19 100644 --- a/include/asm-generic/bitops/atomic.h +++ b/include/asm-generic/bitops/atomic.h @@ -2,7 +2,7 @@ #define _ASM_GENERIC_BITOPS_ATOMIC_H_ #include <asm/types.h> -#include <asm/system.h> +#include <linux/irqflags.h> #ifdef CONFIG_SMP #include <asm/spinlock.h> diff --git a/include/asm-generic/cmpxchg.h b/include/asm-generic/cmpxchg.h index 213ac6e8fe3..14883026015 100644 --- a/include/asm-generic/cmpxchg.h +++ b/include/asm-generic/cmpxchg.h @@ -1,22 +1,98 @@ +/* + * Generic UP xchg and cmpxchg using interrupt disablement. Does not + * support SMP. + */ + #ifndef __ASM_GENERIC_CMPXCHG_H #define __ASM_GENERIC_CMPXCHG_H -/* - * Generic cmpxchg - * - * Uses the local cmpxchg. Does not support SMP. - */ #ifdef CONFIG_SMP #error "Cannot use generic cmpxchg on SMP" #endif +#include <linux/types.h> +#include <linux/irqflags.h> + +#ifndef xchg + +/* + * This function doesn't exist, so you'll get a linker error if + * something tries to do an invalidly-sized xchg(). + */ +extern void __xchg_called_with_bad_pointer(void); + +static inline +unsigned long __xchg(unsigned long x, volatile void *ptr, int size) +{ + unsigned long ret, flags; + + switch (size) { + case 1: +#ifdef __xchg_u8 + return __xchg_u8(x, ptr); +#else + local_irq_save(flags); + ret = *(volatile u8 *)ptr; + *(volatile u8 *)ptr = x; + local_irq_restore(flags); + return ret; +#endif /* __xchg_u8 */ + + case 2: +#ifdef __xchg_u16 + return __xchg_u16(x, ptr); +#else + local_irq_save(flags); + ret = *(volatile u16 *)ptr; + *(volatile u16 *)ptr = x; + local_irq_restore(flags); + return ret; +#endif /* __xchg_u16 */ + + case 4: +#ifdef __xchg_u32 + return __xchg_u32(x, ptr); +#else + local_irq_save(flags); + ret = *(volatile u32 *)ptr; + *(volatile u32 *)ptr = x; + local_irq_restore(flags); + return ret; +#endif /* __xchg_u32 */ + +#ifdef CONFIG_64BIT + case 8: +#ifdef __xchg_u64 + return __xchg_u64(x, ptr); +#else + local_irq_save(flags); + ret = *(volatile u64 *)ptr; + *(volatile u64 *)ptr = x; + local_irq_restore(flags); + return ret; +#endif /* __xchg_u64 */ +#endif /* CONFIG_64BIT */ + + default: + __xchg_called_with_bad_pointer(); + return x; + } +} + +#define xchg(ptr, x) \ + ((__typeof__(*(ptr))) __xchg((unsigned long)(x), (ptr), sizeof(*(ptr)))) + +#endif /* xchg */ + /* * Atomic compare and exchange. * * Do not define __HAVE_ARCH_CMPXCHG because we want to use it to check whether * a cmpxchg primitive faster than repeated local irq save/restore exists. */ +#include <asm-generic/cmpxchg-local.h> + #define cmpxchg(ptr, o, n) cmpxchg_local((ptr), (o), (n)) #define cmpxchg64(ptr, o, n) cmpxchg64_local((ptr), (o), (n)) -#endif +#endif /* __ASM_GENERIC_CMPXCHG_H */ diff --git a/include/asm-generic/exec.h b/include/asm-generic/exec.h new file mode 100644 index 00000000000..567766b0074 --- /dev/null +++ b/include/asm-generic/exec.h @@ -0,0 +1,19 @@ +/* Generic process execution definitions, based on MN10300 definitions. + * + * It should be possible to use these on really simple architectures, + * but it serves more as a starting point for new ports. + * + * Copyright (C) 2007 Red Hat, Inc. All Rights Reserved. + * Written by David Howells (dhowells@redhat.com) + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public Licence + * as published by the Free Software Foundation; either version + * 2 of the Licence, or (at your option) any later version. + */ +#ifndef __ASM_GENERIC_EXEC_H +#define __ASM_GENERIC_EXEC_H + +#define arch_align_stack(x) (x) + +#endif /* __ASM_GENERIC_EXEC_H */ diff --git a/include/asm-generic/gpio.h b/include/asm-generic/gpio.h index 1ff4e221cb4..5f52690c3c8 100644 --- a/include/asm-generic/gpio.h +++ b/include/asm-generic/gpio.h @@ -142,9 +142,9 @@ extern int __must_check gpiochip_reserve(int start, int ngpio); /* add/remove chips */ extern int gpiochip_add(struct gpio_chip *chip); extern int __must_check gpiochip_remove(struct gpio_chip *chip); -extern struct gpio_chip *gpiochip_find(void *data, +extern struct gpio_chip *gpiochip_find(const void *data, int (*match)(struct gpio_chip *chip, - void *data)); + const void *data)); /* Always use the library code for GPIO management calls, diff --git a/include/asm-generic/posix_types.h b/include/asm-generic/posix_types.h index 3dab00860e7..91d44bd4dde 100644 --- a/include/asm-generic/posix_types.h +++ b/include/asm-generic/posix_types.h @@ -10,8 +10,13 @@ * architectures, so that you can override them. */ +#ifndef __kernel_long_t +typedef long __kernel_long_t; +typedef unsigned long __kernel_ulong_t; +#endif + #ifndef __kernel_ino_t -typedef unsigned long __kernel_ino_t; +typedef __kernel_ulong_t __kernel_ino_t; #endif #ifndef __kernel_mode_t @@ -19,7 +24,7 @@ typedef unsigned int __kernel_mode_t; #endif #ifndef __kernel_nlink_t -typedef unsigned long __kernel_nlink_t; +typedef __kernel_ulong_t __kernel_nlink_t; #endif #ifndef __kernel_pid_t @@ -36,7 +41,7 @@ typedef unsigned int __kernel_gid_t; #endif #ifndef __kernel_suseconds_t -typedef long __kernel_suseconds_t; +typedef __kernel_long_t __kernel_suseconds_t; #endif #ifndef __kernel_daddr_t @@ -44,8 +49,8 @@ typedef int __kernel_daddr_t; #endif #ifndef __kernel_uid32_t -typedef __kernel_uid_t __kernel_uid32_t; -typedef __kernel_gid_t __kernel_gid32_t; +typedef unsigned int __kernel_uid32_t; +typedef unsigned int __kernel_gid32_t; #endif #ifndef __kernel_old_uid_t @@ -67,99 +72,29 @@ typedef unsigned int __kernel_size_t; typedef int __kernel_ssize_t; typedef int __kernel_ptrdiff_t; #else -typedef unsigned long __kernel_size_t; -typedef long __kernel_ssize_t; -typedef long __kernel_ptrdiff_t; +typedef __kernel_ulong_t __kernel_size_t; +typedef __kernel_long_t __kernel_ssize_t; +typedef __kernel_long_t __kernel_ptrdiff_t; #endif #endif +#ifndef __kernel_fsid_t +typedef struct { + int val[2]; +} __kernel_fsid_t; +#endif + /* * anything below here should be completely generic */ -typedef long __kernel_off_t; +typedef __kernel_long_t __kernel_off_t; typedef long long __kernel_loff_t; -typedef long __kernel_time_t; -typedef long __kernel_clock_t; +typedef __kernel_long_t __kernel_time_t; +typedef __kernel_long_t __kernel_clock_t; typedef int __kernel_timer_t; typedef int __kernel_clockid_t; typedef char * __kernel_caddr_t; typedef unsigned short __kernel_uid16_t; typedef unsigned short __kernel_gid16_t; -typedef struct { - int val[2]; -} __kernel_fsid_t; - -#ifdef __KERNEL__ - -#undef __FD_SET -static inline void __FD_SET(unsigned long __fd, __kernel_fd_set *__fdsetp) -{ - unsigned long __tmp = __fd / __NFDBITS; - unsigned long __rem = __fd % __NFDBITS; - __fdsetp->fds_bits[__tmp] |= (1UL<<__rem); -} - -#undef __FD_CLR -static inline void __FD_CLR(unsigned long __fd, __kernel_fd_set *__fdsetp) -{ - unsigned long __tmp = __fd / __NFDBITS; - unsigned long __rem = __fd % __NFDBITS; - __fdsetp->fds_bits[__tmp] &= ~(1UL<<__rem); -} - -#undef __FD_ISSET -static inline int __FD_ISSET(unsigned long __fd, const __kernel_fd_set *__p) -{ - unsigned long __tmp = __fd / __NFDBITS; - unsigned long __rem = __fd % __NFDBITS; - return (__p->fds_bits[__tmp] & (1UL<<__rem)) != 0; -} - -/* - * This will unroll the loop for the normal constant case (8 ints, - * for a 256-bit fd_set) - */ -#undef __FD_ZERO -static inline void __FD_ZERO(__kernel_fd_set *__p) -{ - unsigned long *__tmp = __p->fds_bits; - int __i; - - if (__builtin_constant_p(__FDSET_LONGS)) { - switch (__FDSET_LONGS) { - case 16: - __tmp[ 0] = 0; __tmp[ 1] = 0; - __tmp[ 2] = 0; __tmp[ 3] = 0; - __tmp[ 4] = 0; __tmp[ 5] = 0; - __tmp[ 6] = 0; __tmp[ 7] = 0; - __tmp[ 8] = 0; __tmp[ 9] = 0; - __tmp[10] = 0; __tmp[11] = 0; - __tmp[12] = 0; __tmp[13] = 0; - __tmp[14] = 0; __tmp[15] = 0; - return; - - case 8: - __tmp[ 0] = 0; __tmp[ 1] = 0; - __tmp[ 2] = 0; __tmp[ 3] = 0; - __tmp[ 4] = 0; __tmp[ 5] = 0; - __tmp[ 6] = 0; __tmp[ 7] = 0; - return; - - case 4: - __tmp[ 0] = 0; __tmp[ 1] = 0; - __tmp[ 2] = 0; __tmp[ 3] = 0; - return; - } - } - __i = __FDSET_LONGS; - while (__i) { - __i--; - *__tmp = 0; - __tmp++; - } -} - -#endif /* __KERNEL__ */ - #endif /* __ASM_GENERIC_POSIX_TYPES_H */ diff --git a/include/asm-generic/switch_to.h b/include/asm-generic/switch_to.h new file mode 100644 index 00000000000..052c4ac04fd --- /dev/null +++ b/include/asm-generic/switch_to.h @@ -0,0 +1,30 @@ +/* Generic task switch macro wrapper, based on MN10300 definitions. + * + * It should be possible to use these on really simple architectures, + * but it serves more as a starting point for new ports. + * + * Copyright (C) 2007 Red Hat, Inc. All Rights Reserved. + * Written by David Howells (dhowells@redhat.com) + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public Licence + * as published by the Free Software Foundation; either version + * 2 of the Licence, or (at your option) any later version. + */ +#ifndef __ASM_GENERIC_SWITCH_TO_H +#define __ASM_GENERIC_SWITCH_TO_H + +#include <linux/thread_info.h> + +/* + * Context switching is now performed out-of-line in switch_to.S + */ +extern struct task_struct *__switch_to(struct task_struct *, + struct task_struct *); + +#define switch_to(prev, next, last) \ + do { \ + ((last) = __switch_to((prev), (next))); \ + } while (0) + +#endif /* __ASM_GENERIC_SWITCH_TO_H */ diff --git a/include/asm-generic/system.h b/include/asm-generic/system.h deleted file mode 100644 index 215efa74f5a..00000000000 --- a/include/asm-generic/system.h +++ /dev/null @@ -1,141 +0,0 @@ -/* Generic system definitions, based on MN10300 definitions. - * - * It should be possible to use these on really simple architectures, - * but it serves more as a starting point for new ports. - * - * Copyright (C) 2007 Red Hat, Inc. All Rights Reserved. - * Written by David Howells (dhowells@redhat.com) - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public Licence - * as published by the Free Software Foundation; either version - * 2 of the Licence, or (at your option) any later version. - */ -#ifndef __ASM_GENERIC_SYSTEM_H -#define __ASM_GENERIC_SYSTEM_H - -#ifndef __ASSEMBLY__ - -#include <linux/types.h> -#include <linux/irqflags.h> - -#include <asm/cmpxchg-local.h> -#include <asm/cmpxchg.h> - -struct task_struct; - -/* context switching is now performed out-of-line in switch_to.S */ -extern struct task_struct *__switch_to(struct task_struct *, - struct task_struct *); -#define switch_to(prev, next, last) \ - do { \ - ((last) = __switch_to((prev), (next))); \ - } while (0) - -#define arch_align_stack(x) (x) - -#define nop() asm volatile ("nop") - -#endif /* !__ASSEMBLY__ */ - -/* - * Force strict CPU ordering. - * And yes, this is required on UP too when we're talking - * to devices. - * - * This implementation only contains a compiler barrier. - */ - -#define mb() asm volatile ("": : :"memory") -#define rmb() mb() -#define wmb() asm volatile ("": : :"memory") - -#ifdef CONFIG_SMP -#define smp_mb() mb() -#define smp_rmb() rmb() -#define smp_wmb() wmb() -#else -#define smp_mb() barrier() -#define smp_rmb() barrier() -#define smp_wmb() barrier() -#endif - -#define set_mb(var, value) do { var = value; mb(); } while (0) -#define set_wmb(var, value) do { var = value; wmb(); } while (0) - -#define read_barrier_depends() do {} while (0) -#define smp_read_barrier_depends() do {} while (0) - -/* - * we make sure local_irq_enable() doesn't cause priority inversion - */ -#ifndef __ASSEMBLY__ - -/* This function doesn't exist, so you'll get a linker error - * if something tries to do an invalid xchg(). */ -extern void __xchg_called_with_bad_pointer(void); - -static inline -unsigned long __xchg(unsigned long x, volatile void *ptr, int size) -{ - unsigned long ret, flags; - - switch (size) { - case 1: -#ifdef __xchg_u8 - return __xchg_u8(x, ptr); -#else - local_irq_save(flags); - ret = *(volatile u8 *)ptr; - *(volatile u8 *)ptr = x; - local_irq_restore(flags); - return ret; -#endif /* __xchg_u8 */ - - case 2: -#ifdef __xchg_u16 - return __xchg_u16(x, ptr); -#else - local_irq_save(flags); - ret = *(volatile u16 *)ptr; - *(volatile u16 *)ptr = x; - local_irq_restore(flags); - return ret; -#endif /* __xchg_u16 */ - - case 4: -#ifdef __xchg_u32 - return __xchg_u32(x, ptr); -#else - local_irq_save(flags); - ret = *(volatile u32 *)ptr; - *(volatile u32 *)ptr = x; - local_irq_restore(flags); - return ret; -#endif /* __xchg_u32 */ - -#ifdef CONFIG_64BIT - case 8: -#ifdef __xchg_u64 - return __xchg_u64(x, ptr); -#else - local_irq_save(flags); - ret = *(volatile u64 *)ptr; - *(volatile u64 *)ptr = x; - local_irq_restore(flags); - return ret; -#endif /* __xchg_u64 */ -#endif /* CONFIG_64BIT */ - - default: - __xchg_called_with_bad_pointer(); - return x; - } -} - -#define xchg(ptr, x) \ - ((__typeof__(*(ptr))) __xchg((unsigned long)(x), (ptr), sizeof(*(ptr)))) - -#endif /* !__ASSEMBLY__ */ - -#endif /* __ASM_GENERIC_SYSTEM_H */ diff --git a/include/asm-generic/unistd.h b/include/asm-generic/unistd.h index 2292d1af9d7..991ef01cd77 100644 --- a/include/asm-generic/unistd.h +++ b/include/asm-generic/unistd.h @@ -218,7 +218,7 @@ __SC_COMP(__NR_pwritev, sys_pwritev, compat_sys_pwritev) /* fs/sendfile.c */ #define __NR3264_sendfile 71 -__SC_3264(__NR3264_sendfile, sys_sendfile64, sys_sendfile) +__SYSCALL(__NR3264_sendfile, sys_sendfile64) /* fs/select.c */ #define __NR_pselect6 72 diff --git a/include/asm-generic/vmlinux.lds.h b/include/asm-generic/vmlinux.lds.h index 798603e8ec3..8aeadf6b553 100644 --- a/include/asm-generic/vmlinux.lds.h +++ b/include/asm-generic/vmlinux.lds.h @@ -616,30 +616,23 @@ *(.init.setup) \ VMLINUX_SYMBOL(__setup_end) = .; -#define INITCALLS \ - *(.initcallearly.init) \ - VMLINUX_SYMBOL(__early_initcall_end) = .; \ - *(.initcall0.init) \ - *(.initcall0s.init) \ - *(.initcall1.init) \ - *(.initcall1s.init) \ - *(.initcall2.init) \ - *(.initcall2s.init) \ - *(.initcall3.init) \ - *(.initcall3s.init) \ - *(.initcall4.init) \ - *(.initcall4s.init) \ - *(.initcall5.init) \ - *(.initcall5s.init) \ - *(.initcallrootfs.init) \ - *(.initcall6.init) \ - *(.initcall6s.init) \ - *(.initcall7.init) \ - *(.initcall7s.init) +#define INIT_CALLS_LEVEL(level) \ + VMLINUX_SYMBOL(__initcall##level##_start) = .; \ + *(.initcall##level##.init) \ + *(.initcall##level##s.init) \ #define INIT_CALLS \ VMLINUX_SYMBOL(__initcall_start) = .; \ - INITCALLS \ + *(.initcallearly.init) \ + INIT_CALLS_LEVEL(0) \ + INIT_CALLS_LEVEL(1) \ + INIT_CALLS_LEVEL(2) \ + INIT_CALLS_LEVEL(3) \ + INIT_CALLS_LEVEL(4) \ + INIT_CALLS_LEVEL(5) \ + INIT_CALLS_LEVEL(rootfs) \ + INIT_CALLS_LEVEL(6) \ + INIT_CALLS_LEVEL(7) \ VMLINUX_SYMBOL(__initcall_end) = .; #define CON_INITCALL \ diff --git a/include/crypto/internal/aead.h b/include/crypto/internal/aead.h index d838c945575..2eba340230a 100644 --- a/include/crypto/internal/aead.h +++ b/include/crypto/internal/aead.h @@ -31,6 +31,8 @@ static inline void crypto_set_aead_spawn( crypto_set_spawn(&spawn->base, inst); } +struct crypto_alg *crypto_lookup_aead(const char *name, u32 type, u32 mask); + int crypto_grab_aead(struct crypto_aead_spawn *spawn, const char *name, u32 type, u32 mask); diff --git a/include/crypto/internal/skcipher.h b/include/crypto/internal/skcipher.h index 3a748a6bf77..06e8b32d541 100644 --- a/include/crypto/internal/skcipher.h +++ b/include/crypto/internal/skcipher.h @@ -34,6 +34,8 @@ static inline void crypto_set_skcipher_spawn( int crypto_grab_skcipher(struct crypto_skcipher_spawn *spawn, const char *name, u32 type, u32 mask); +struct crypto_alg *crypto_lookup_skcipher(const char *name, u32 type, u32 mask); + static inline void crypto_drop_skcipher(struct crypto_skcipher_spawn *spawn) { crypto_drop_spawn(&spawn->base); diff --git a/include/drm/drm.h b/include/drm/drm.h index 34a7b89fd00..64ff02d5b73 100644 --- a/include/drm/drm.h +++ b/include/drm/drm.h @@ -617,6 +617,17 @@ struct drm_get_cap { __u64 value; }; +#define DRM_CLOEXEC O_CLOEXEC +struct drm_prime_handle { + __u32 handle; + + /** Flags.. only applicable for handle->fd */ + __u32 flags; + + /** Returned dmabuf file descriptor */ + __s32 fd; +}; + #include "drm_mode.h" #define DRM_IOCTL_BASE 'd' @@ -673,7 +684,8 @@ struct drm_get_cap { #define DRM_IOCTL_UNLOCK DRM_IOW( 0x2b, struct drm_lock) #define DRM_IOCTL_FINISH DRM_IOW( 0x2c, struct drm_lock) -#define DRM_IOCTL_GEM_PRIME_OPEN DRM_IOWR(0x2e, struct drm_gem_open) +#define DRM_IOCTL_PRIME_HANDLE_TO_FD DRM_IOWR(0x2d, struct drm_prime_handle) +#define DRM_IOCTL_PRIME_FD_TO_HANDLE DRM_IOWR(0x2e, struct drm_prime_handle) #define DRM_IOCTL_AGP_ACQUIRE DRM_IO( 0x30) #define DRM_IOCTL_AGP_RELEASE DRM_IO( 0x31) diff --git a/include/drm/drmP.h b/include/drm/drmP.h index 574bd1c81eb..dd731043fec 100644 --- a/include/drm/drmP.h +++ b/include/drm/drmP.h @@ -91,6 +91,7 @@ struct drm_device; #define DRM_UT_CORE 0x01 #define DRM_UT_DRIVER 0x02 #define DRM_UT_KMS 0x04 +#define DRM_UT_PRIME 0x08 /* * Three debug levels are defined. * drm_core, drm_driver, drm_kms @@ -150,6 +151,7 @@ int drm_err(const char *func, const char *format, ...); #define DRIVER_IRQ_VBL2 0x800 #define DRIVER_GEM 0x1000 #define DRIVER_MODESET 0x2000 +#define DRIVER_PRIME 0x4000 #define DRIVER_BUS_PCI 0x1 #define DRIVER_BUS_PLATFORM 0x2 @@ -215,6 +217,11 @@ int drm_err(const char *func, const char *format, ...); drm_ut_debug_printk(DRM_UT_KMS, DRM_NAME, \ __func__, fmt, ##args); \ } while (0) +#define DRM_DEBUG_PRIME(fmt, args...) \ + do { \ + drm_ut_debug_printk(DRM_UT_PRIME, DRM_NAME, \ + __func__, fmt, ##args); \ + } while (0) #define DRM_LOG(fmt, args...) \ do { \ drm_ut_debug_printk(DRM_UT_CORE, NULL, \ @@ -238,6 +245,7 @@ int drm_err(const char *func, const char *format, ...); #else #define DRM_DEBUG_DRIVER(fmt, args...) do { } while (0) #define DRM_DEBUG_KMS(fmt, args...) do { } while (0) +#define DRM_DEBUG_PRIME(fmt, args...) do { } while (0) #define DRM_DEBUG(fmt, arg...) do { } while (0) #define DRM_LOG(fmt, arg...) do { } while (0) #define DRM_LOG_KMS(fmt, args...) do { } while (0) @@ -410,6 +418,12 @@ struct drm_pending_event { void (*destroy)(struct drm_pending_event *event); }; +/* initial implementaton using a linked list - todo hashtab */ +struct drm_prime_file_private { + struct list_head head; + struct mutex lock; +}; + /** File private data */ struct drm_file { int authenticated; @@ -437,6 +451,8 @@ struct drm_file { wait_queue_head_t event_wait; struct list_head event_list; int event_space; + + struct drm_prime_file_private prime; }; /** Wait queue */ @@ -652,6 +668,12 @@ struct drm_gem_object { uint32_t pending_write_domain; void *driver_private; + + /* dma buf exported from this GEM object */ + struct dma_buf *export_dma_buf; + + /* dma buf attachment backing this object */ + struct dma_buf_attachment *import_attach; }; #include "drm_crtc.h" @@ -890,6 +912,20 @@ struct drm_driver { int (*gem_open_object) (struct drm_gem_object *, struct drm_file *); void (*gem_close_object) (struct drm_gem_object *, struct drm_file *); + /* prime: */ + /* export handle -> fd (see drm_gem_prime_handle_to_fd() helper) */ + int (*prime_handle_to_fd)(struct drm_device *dev, struct drm_file *file_priv, + uint32_t handle, uint32_t flags, int *prime_fd); + /* import fd -> handle (see drm_gem_prime_fd_to_handle() helper) */ + int (*prime_fd_to_handle)(struct drm_device *dev, struct drm_file *file_priv, + int prime_fd, uint32_t *handle); + /* export GEM -> dmabuf */ + struct dma_buf * (*gem_prime_export)(struct drm_device *dev, + struct drm_gem_object *obj, int flags); + /* import dmabuf -> GEM */ + struct drm_gem_object * (*gem_prime_import)(struct drm_device *dev, + struct dma_buf *dma_buf); + /* vga arb irq handler */ void (*vgaarb_irq)(struct drm_device *dev, bool state); @@ -1509,6 +1545,32 @@ extern int drm_vblank_info(struct seq_file *m, void *data); extern int drm_clients_info(struct seq_file *m, void* data); extern int drm_gem_name_info(struct seq_file *m, void *data); + +extern int drm_gem_prime_handle_to_fd(struct drm_device *dev, + struct drm_file *file_priv, uint32_t handle, uint32_t flags, + int *prime_fd); +extern int drm_gem_prime_fd_to_handle(struct drm_device *dev, + struct drm_file *file_priv, int prime_fd, uint32_t *handle); + +extern int drm_prime_handle_to_fd_ioctl(struct drm_device *dev, void *data, + struct drm_file *file_priv); +extern int drm_prime_fd_to_handle_ioctl(struct drm_device *dev, void *data, + struct drm_file *file_priv); + +extern struct sg_table *drm_prime_pages_to_sg(struct page **pages, int nr_pages); +extern void drm_prime_gem_destroy(struct drm_gem_object *obj, struct sg_table *sg); + + +void drm_prime_init_file_private(struct drm_prime_file_private *prime_fpriv); +void drm_prime_destroy_file_private(struct drm_prime_file_private *prime_fpriv); +int drm_prime_add_imported_buf_handle(struct drm_prime_file_private *prime_fpriv, struct dma_buf *dma_buf, uint32_t handle); +int drm_prime_lookup_imported_buf_handle(struct drm_prime_file_private *prime_fpriv, struct dma_buf *dma_buf, uint32_t *handle); +void drm_prime_remove_imported_buf_handle(struct drm_prime_file_private *prime_fpriv, struct dma_buf *dma_buf); + +int drm_prime_add_dma_buf(struct drm_device *dev, struct drm_gem_object *obj); +int drm_prime_lookup_obj(struct drm_device *dev, struct dma_buf *buf, + struct drm_gem_object **obj); + #if DRM_DEBUG_CODE extern int drm_vma_info(struct seq_file *m, void *data); #endif diff --git a/include/drm/intel-gtt.h b/include/drm/intel-gtt.h index 0a0001b9dc7..923afb5dcf0 100644 --- a/include/drm/intel-gtt.h +++ b/include/drm/intel-gtt.h @@ -44,4 +44,8 @@ void intel_gtt_insert_pages(unsigned int first_entry, unsigned int num_entries, /* flag for GFDT type */ #define AGP_USER_CACHED_MEMORY_GFDT (1 << 3) +#ifdef CONFIG_INTEL_IOMMU +extern int intel_iommu_gfx_mapped; +#endif + #endif diff --git a/include/linux/Kbuild b/include/linux/Kbuild index a2555538109..3c9b616c834 100644 --- a/include/linux/Kbuild +++ b/include/linux/Kbuild @@ -3,6 +3,7 @@ header-y += can/ header-y += caif/ header-y += dvb/ header-y += hdlc/ +header-y += hsi/ header-y += isdn/ header-y += mmc/ header-y += nfsd/ @@ -120,7 +121,6 @@ header-y += errno.h header-y += errqueue.h header-y += ethtool.h header-y += eventpoll.h -header-y += ext2_fs.h header-y += fadvise.h header-y += falloc.h header-y += fanotify.h @@ -357,6 +357,7 @@ header-y += suspend_ioctls.h header-y += swab.h header-y += synclink.h header-y += sysctl.h +header-y += sysinfo.h header-y += taskstats.h header-y += tcp.h header-y += telephony.h diff --git a/include/linux/acpi.h b/include/linux/acpi.h index 3f968665899..f421dd84f29 100644 --- a/include/linux/acpi.h +++ b/include/linux/acpi.h @@ -151,6 +151,7 @@ extern int ec_write(u8 addr, u8 val); extern int ec_transaction(u8 command, const u8 *wdata, unsigned wdata_len, u8 *rdata, unsigned rdata_len); +extern acpi_handle ec_get_handle(void); #if defined(CONFIG_ACPI_WMI) || defined(CONFIG_ACPI_WMI_MODULE) @@ -371,4 +372,14 @@ static inline int acpi_nvs_for_each_region(int (*func)(__u64, __u64, void *), #endif /* !CONFIG_ACPI */ +#ifdef CONFIG_ACPI +void acpi_os_set_prepare_sleep(int (*func)(u8 sleep_state, + u32 pm1a_ctrl, u32 pm1b_ctrl)); + +acpi_status acpi_os_prepare_sleep(u8 sleep_state, + u32 pm1a_control, u32 pm1b_control); +#else +#define acpi_os_set_prepare_sleep(func, pm1a_ctrl, pm1b_ctrl) do { } while (0) +#endif + #endif /*_LINUX_ACPI_H*/ diff --git a/include/linux/aio_abi.h b/include/linux/aio_abi.h index 2c873166418..86fa7a71336 100644 --- a/include/linux/aio_abi.h +++ b/include/linux/aio_abi.h @@ -30,7 +30,7 @@ #include <linux/types.h> #include <asm/byteorder.h> -typedef unsigned long aio_context_t; +typedef __kernel_ulong_t aio_context_t; enum { IOCB_CMD_PREAD = 0, diff --git a/include/linux/amba/pl08x.h b/include/linux/amba/pl08x.h index 033f6aa670d..e64ce2cfee9 100644 --- a/include/linux/amba/pl08x.h +++ b/include/linux/amba/pl08x.h @@ -47,9 +47,6 @@ enum { * @muxval: a number usually used to poke into some mux regiser to * mux in the signal to this channel * @cctl_opt: default options for the channel control register - * @device_fc: Flow Controller Settings for ccfg register. Only valid for slave - * channels. Fill with 'true' if peripheral should be flow controller. Direction - * will be selected at Runtime. * @addr: source/target address in physical memory for this DMA channel, * can be the address of a FIFO register for burst requests for example. * This can be left undefined if the PrimeCell API is used for configuring @@ -68,7 +65,6 @@ struct pl08x_channel_data { int max_signal; u32 muxval; u32 cctl; - bool device_fc; dma_addr_t addr; bool circular_buffer; bool single; @@ -176,13 +172,15 @@ enum pl08x_dma_chan_state { * @runtime_addr: address for RX/TX according to the runtime config * @runtime_direction: current direction of this channel according to * runtime config - * @lc: last completed transaction on this channel * @pend_list: queued transactions pending on this channel * @at: active transaction on this channel * @lock: a lock for this channel data * @host: a pointer to the host (internal use) * @state: whether the channel is idle, paused, running etc * @slave: whether this channel is a device (slave) or for memcpy + * @device_fc: Flow Controller Settings for ccfg register. Only valid for slave + * channels. Fill with 'true' if peripheral should be flow controller. Direction + * will be selected at Runtime. * @waiting: a TX descriptor on this channel which is waiting for a physical * channel to become available */ @@ -198,13 +196,13 @@ struct pl08x_dma_chan { u32 src_cctl; u32 dst_cctl; enum dma_transfer_direction runtime_direction; - dma_cookie_t lc; struct list_head pend_list; struct pl08x_txd *at; spinlock_t lock; struct pl08x_driver_data *host; enum pl08x_dma_chan_state state; bool slave; + bool device_fc; struct pl08x_txd *waiting; }; diff --git a/include/linux/amba/pl330.h b/include/linux/amba/pl330.h index 12e023c19ac..fe93758e840 100644 --- a/include/linux/amba/pl330.h +++ b/include/linux/amba/pl330.h @@ -13,7 +13,6 @@ #define __AMBA_PL330_H_ #include <linux/dmaengine.h> -#include <asm/hardware/pl330.h> struct dma_pl330_platdata { /* diff --git a/include/linux/apple_bl.h b/include/linux/apple_bl.h new file mode 100644 index 00000000000..47bedc0eee6 --- /dev/null +++ b/include/linux/apple_bl.h @@ -0,0 +1,26 @@ +/* + * apple_bl exported symbols + */ + +#ifndef _LINUX_APPLE_BL_H +#define _LINUX_APPLE_BL_H + +#ifdef CONFIG_BACKLIGHT_APPLE + +extern int apple_bl_register(void); +extern void apple_bl_unregister(void); + +#else /* !CONFIG_BACKLIGHT_APPLE */ + +static inline int apple_bl_register(void) +{ + return 0; +} + +static inline void apple_bl_unregister(void) +{ +} + +#endif /* !CONFIG_BACKLIGHT_APPLE */ + +#endif /* _LINUX_APPLE_BL_H */ diff --git a/include/linux/atmel_tc.h b/include/linux/atmel_tc.h index 53ba65e30ca..1d14b1dc1ae 100644 --- a/include/linux/atmel_tc.h +++ b/include/linux/atmel_tc.h @@ -34,10 +34,19 @@ struct clk; /** + * struct atmel_tcb_config - SoC data for a Timer/Counter Block + * @counter_width: size in bits of a timer counter register + */ +struct atmel_tcb_config { + size_t counter_width; +}; + +/** * struct atmel_tc - information about a Timer/Counter Block * @pdev: physical device * @iomem: resource associated with the I/O register * @regs: mapping through which the I/O registers can be accessed + * @tcb_config: configuration data from SoC * @irq: irq for each of the three channels * @clk: internal clock source for each of the three channels * @node: list node, for tclib internal use @@ -54,6 +63,7 @@ struct atmel_tc { struct platform_device *pdev; struct resource *iomem; void __iomem *regs; + struct atmel_tcb_config *tcb_config; int irq[3]; struct clk *clk[3]; struct list_head node; diff --git a/include/linux/ceph/libceph.h b/include/linux/ceph/libceph.h index e8cf0ccd1a8..e71d683982a 100644 --- a/include/linux/ceph/libceph.h +++ b/include/linux/ceph/libceph.h @@ -208,7 +208,7 @@ extern struct kmem_cache *ceph_cap_cachep; extern struct kmem_cache *ceph_dentry_cachep; extern struct kmem_cache *ceph_file_cachep; -extern int ceph_parse_options(struct ceph_options **popt, char *options, +extern struct ceph_options *ceph_parse_options(char *options, const char *dev_name, const char *dev_name_end, int (*parse_extra_token)(char *c, void *private), void *private); diff --git a/include/linux/ceph/messenger.h b/include/linux/ceph/messenger.h index ffbeb2c217b..3bff047f6b0 100644 --- a/include/linux/ceph/messenger.h +++ b/include/linux/ceph/messenger.h @@ -14,8 +14,6 @@ struct ceph_msg; struct ceph_connection; -extern struct workqueue_struct *ceph_msgr_wq; /* receive work queue */ - /* * Ceph defines these callbacks for handling connection events. */ @@ -54,7 +52,6 @@ struct ceph_connection_operations { struct ceph_messenger { struct ceph_entity_inst inst; /* my name+address */ struct ceph_entity_addr my_enc_addr; - struct page *zero_page; /* used in certain error cases */ bool nocrc; @@ -101,7 +98,7 @@ struct ceph_msg { struct ceph_msg_pos { int page, page_pos; /* which page; offset in page */ int data_pos; /* offset in data payload */ - int did_page_crc; /* true if we've calculated crc for current page */ + bool did_page_crc; /* true if we've calculated crc for current page */ }; /* ceph connection fault delay defaults, for exponential backoff */ diff --git a/include/linux/clk-private.h b/include/linux/clk-private.h new file mode 100644 index 00000000000..5e4312b6f5c --- /dev/null +++ b/include/linux/clk-private.h @@ -0,0 +1,196 @@ +/* + * linux/include/linux/clk-private.h + * + * Copyright (c) 2010-2011 Jeremy Kerr <jeremy.kerr@canonical.com> + * Copyright (C) 2011-2012 Linaro Ltd <mturquette@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef __LINUX_CLK_PRIVATE_H +#define __LINUX_CLK_PRIVATE_H + +#include <linux/clk-provider.h> +#include <linux/list.h> + +/* + * WARNING: Do not include clk-private.h from any file that implements struct + * clk_ops. Doing so is a layering violation! + * + * This header exists only to allow for statically initialized clock data. Any + * static clock data must be defined in a separate file from the logic that + * implements the clock operations for that same data. + */ + +#ifdef CONFIG_COMMON_CLK + +struct clk { + const char *name; + const struct clk_ops *ops; + struct clk_hw *hw; + struct clk *parent; + char **parent_names; + struct clk **parents; + u8 num_parents; + unsigned long rate; + unsigned long new_rate; + unsigned long flags; + unsigned int enable_count; + unsigned int prepare_count; + struct hlist_head children; + struct hlist_node child_node; + unsigned int notifier_count; +#ifdef CONFIG_COMMON_CLK_DEBUG + struct dentry *dentry; +#endif +}; + +/* + * DOC: Basic clock implementations common to many platforms + * + * Each basic clock hardware type is comprised of a structure describing the + * clock hardware, implementations of the relevant callbacks in struct clk_ops, + * unique flags for that hardware type, a registration function and an + * alternative macro for static initialization + */ + +extern struct clk_ops clk_fixed_rate_ops; + +#define DEFINE_CLK_FIXED_RATE(_name, _flags, _rate, \ + _fixed_rate_flags) \ + static struct clk _name; \ + static char *_name##_parent_names[] = {}; \ + static struct clk_fixed_rate _name##_hw = { \ + .hw = { \ + .clk = &_name, \ + }, \ + .fixed_rate = _rate, \ + .flags = _fixed_rate_flags, \ + }; \ + static struct clk _name = { \ + .name = #_name, \ + .ops = &clk_fixed_rate_ops, \ + .hw = &_name##_hw.hw, \ + .parent_names = _name##_parent_names, \ + .num_parents = \ + ARRAY_SIZE(_name##_parent_names), \ + .flags = _flags, \ + }; + +extern struct clk_ops clk_gate_ops; + +#define DEFINE_CLK_GATE(_name, _parent_name, _parent_ptr, \ + _flags, _reg, _bit_idx, \ + _gate_flags, _lock) \ + static struct clk _name; \ + static char *_name##_parent_names[] = { \ + _parent_name, \ + }; \ + static struct clk *_name##_parents[] = { \ + _parent_ptr, \ + }; \ + static struct clk_gate _name##_hw = { \ + .hw = { \ + .clk = &_name, \ + }, \ + .reg = _reg, \ + .bit_idx = _bit_idx, \ + .flags = _gate_flags, \ + .lock = _lock, \ + }; \ + static struct clk _name = { \ + .name = #_name, \ + .ops = &clk_gate_ops, \ + .hw = &_name##_hw.hw, \ + .parent_names = _name##_parent_names, \ + .num_parents = \ + ARRAY_SIZE(_name##_parent_names), \ + .parents = _name##_parents, \ + .flags = _flags, \ + }; + +extern struct clk_ops clk_divider_ops; + +#define DEFINE_CLK_DIVIDER(_name, _parent_name, _parent_ptr, \ + _flags, _reg, _shift, _width, \ + _divider_flags, _lock) \ + static struct clk _name; \ + static char *_name##_parent_names[] = { \ + _parent_name, \ + }; \ + static struct clk *_name##_parents[] = { \ + _parent_ptr, \ + }; \ + static struct clk_divider _name##_hw = { \ + .hw = { \ + .clk = &_name, \ + }, \ + .reg = _reg, \ + .shift = _shift, \ + .width = _width, \ + .flags = _divider_flags, \ + .lock = _lock, \ + }; \ + static struct clk _name = { \ + .name = #_name, \ + .ops = &clk_divider_ops, \ + .hw = &_name##_hw.hw, \ + .parent_names = _name##_parent_names, \ + .num_parents = \ + ARRAY_SIZE(_name##_parent_names), \ + .parents = _name##_parents, \ + .flags = _flags, \ + }; + +extern struct clk_ops clk_mux_ops; + +#define DEFINE_CLK_MUX(_name, _parent_names, _parents, _flags, \ + _reg, _shift, _width, \ + _mux_flags, _lock) \ + static struct clk _name; \ + static struct clk_mux _name##_hw = { \ + .hw = { \ + .clk = &_name, \ + }, \ + .reg = _reg, \ + .shift = _shift, \ + .width = _width, \ + .flags = _mux_flags, \ + .lock = _lock, \ + }; \ + static struct clk _name = { \ + .name = #_name, \ + .ops = &clk_mux_ops, \ + .hw = &_name##_hw.hw, \ + .parent_names = _parent_names, \ + .num_parents = \ + ARRAY_SIZE(_parent_names), \ + .parents = _parents, \ + .flags = _flags, \ + }; + +/** + * __clk_init - initialize the data structures in a struct clk + * @dev: device initializing this clk, placeholder for now + * @clk: clk being initialized + * + * Initializes the lists in struct clk, queries the hardware for the + * parent and rate and sets them both. + * + * Any struct clk passed into __clk_init must have the following members + * populated: + * .name + * .ops + * .hw + * .parent_names + * .num_parents + * .flags + * + * It is not necessary to call clk_register if __clk_init is used directly with + * statically initialized clock data. + */ +void __clk_init(struct device *dev, struct clk *clk); + +#endif /* CONFIG_COMMON_CLK */ +#endif /* CLK_PRIVATE_H */ diff --git a/include/linux/clk-provider.h b/include/linux/clk-provider.h new file mode 100644 index 00000000000..5508897ad37 --- /dev/null +++ b/include/linux/clk-provider.h @@ -0,0 +1,300 @@ +/* + * linux/include/linux/clk-provider.h + * + * Copyright (c) 2010-2011 Jeremy Kerr <jeremy.kerr@canonical.com> + * Copyright (C) 2011-2012 Linaro Ltd <mturquette@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef __LINUX_CLK_PROVIDER_H +#define __LINUX_CLK_PROVIDER_H + +#include <linux/clk.h> + +#ifdef CONFIG_COMMON_CLK + +/** + * struct clk_hw - handle for traversing from a struct clk to its corresponding + * hardware-specific structure. struct clk_hw should be declared within struct + * clk_foo and then referenced by the struct clk instance that uses struct + * clk_foo's clk_ops + * + * clk: pointer to the struct clk instance that points back to this struct + * clk_hw instance + */ +struct clk_hw { + struct clk *clk; +}; + +/* + * flags used across common struct clk. these flags should only affect the + * top-level framework. custom flags for dealing with hardware specifics + * belong in struct clk_foo + */ +#define CLK_SET_RATE_GATE BIT(0) /* must be gated across rate change */ +#define CLK_SET_PARENT_GATE BIT(1) /* must be gated across re-parent */ +#define CLK_SET_RATE_PARENT BIT(2) /* propagate rate change up one level */ +#define CLK_IGNORE_UNUSED BIT(3) /* do not gate even if unused */ +#define CLK_IS_ROOT BIT(4) /* root clk, has no parent */ + +/** + * struct clk_ops - Callback operations for hardware clocks; these are to + * be provided by the clock implementation, and will be called by drivers + * through the clk_* api. + * + * @prepare: Prepare the clock for enabling. This must not return until + * the clock is fully prepared, and it's safe to call clk_enable. + * This callback is intended to allow clock implementations to + * do any initialisation that may sleep. Called with + * prepare_lock held. + * + * @unprepare: Release the clock from its prepared state. This will typically + * undo any work done in the @prepare callback. Called with + * prepare_lock held. + * + * @enable: Enable the clock atomically. This must not return until the + * clock is generating a valid clock signal, usable by consumer + * devices. Called with enable_lock held. This function must not + * sleep. + * + * @disable: Disable the clock atomically. Called with enable_lock held. + * This function must not sleep. + * + * @recalc_rate Recalculate the rate of this clock, by quering hardware. The + * parent rate is an input parameter. It is up to the caller to + * insure that the prepare_mutex is held across this call. + * Returns the calculated rate. Optional, but recommended - if + * this op is not set then clock rate will be initialized to 0. + * + * @round_rate: Given a target rate as input, returns the closest rate actually + * supported by the clock. + * + * @get_parent: Queries the hardware to determine the parent of a clock. The + * return value is a u8 which specifies the index corresponding to + * the parent clock. This index can be applied to either the + * .parent_names or .parents arrays. In short, this function + * translates the parent value read from hardware into an array + * index. Currently only called when the clock is initialized by + * __clk_init. This callback is mandatory for clocks with + * multiple parents. It is optional (and unnecessary) for clocks + * with 0 or 1 parents. + * + * @set_parent: Change the input source of this clock; for clocks with multiple + * possible parents specify a new parent by passing in the index + * as a u8 corresponding to the parent in either the .parent_names + * or .parents arrays. This function in affect translates an + * array index into the value programmed into the hardware. + * Returns 0 on success, -EERROR otherwise. + * + * @set_rate: Change the rate of this clock. If this callback returns + * CLK_SET_RATE_PARENT, the rate change will be propagated to the + * parent clock (which may propagate again if the parent clock + * also sets this flag). The requested rate of the parent is + * passed back from the callback in the second 'unsigned long *' + * argument. Note that it is up to the hardware clock's set_rate + * implementation to insure that clocks do not run out of spec + * when propgating the call to set_rate up to the parent. One way + * to do this is to gate the clock (via clk_disable and/or + * clk_unprepare) before calling clk_set_rate, then ungating it + * afterward. If your clock also has the CLK_GATE_SET_RATE flag + * set then this will insure safety. Returns 0 on success, + * -EERROR otherwise. + * + * The clk_enable/clk_disable and clk_prepare/clk_unprepare pairs allow + * implementations to split any work between atomic (enable) and sleepable + * (prepare) contexts. If enabling a clock requires code that might sleep, + * this must be done in clk_prepare. Clock enable code that will never be + * called in a sleepable context may be implement in clk_enable. + * + * Typically, drivers will call clk_prepare when a clock may be needed later + * (eg. when a device is opened), and clk_enable when the clock is actually + * required (eg. from an interrupt). Note that clk_prepare MUST have been + * called before clk_enable. + */ +struct clk_ops { + int (*prepare)(struct clk_hw *hw); + void (*unprepare)(struct clk_hw *hw); + int (*enable)(struct clk_hw *hw); + void (*disable)(struct clk_hw *hw); + int (*is_enabled)(struct clk_hw *hw); + unsigned long (*recalc_rate)(struct clk_hw *hw, + unsigned long parent_rate); + long (*round_rate)(struct clk_hw *hw, unsigned long, + unsigned long *); + int (*set_parent)(struct clk_hw *hw, u8 index); + u8 (*get_parent)(struct clk_hw *hw); + int (*set_rate)(struct clk_hw *hw, unsigned long); + void (*init)(struct clk_hw *hw); +}; + +/* + * DOC: Basic clock implementations common to many platforms + * + * Each basic clock hardware type is comprised of a structure describing the + * clock hardware, implementations of the relevant callbacks in struct clk_ops, + * unique flags for that hardware type, a registration function and an + * alternative macro for static initialization + */ + +/** + * struct clk_fixed_rate - fixed-rate clock + * @hw: handle between common and hardware-specific interfaces + * @fixed_rate: constant frequency of clock + */ +struct clk_fixed_rate { + struct clk_hw hw; + unsigned long fixed_rate; + u8 flags; +}; + +struct clk *clk_register_fixed_rate(struct device *dev, const char *name, + const char *parent_name, unsigned long flags, + unsigned long fixed_rate); + +/** + * struct clk_gate - gating clock + * + * @hw: handle between common and hardware-specific interfaces + * @reg: register controlling gate + * @bit_idx: single bit controlling gate + * @flags: hardware-specific flags + * @lock: register lock + * + * Clock which can gate its output. Implements .enable & .disable + * + * Flags: + * CLK_GATE_SET_DISABLE - by default this clock sets the bit at bit_idx to + * enable the clock. Setting this flag does the opposite: setting the bit + * disable the clock and clearing it enables the clock + */ +struct clk_gate { + struct clk_hw hw; + void __iomem *reg; + u8 bit_idx; + u8 flags; + spinlock_t *lock; + char *parent[1]; +}; + +#define CLK_GATE_SET_TO_DISABLE BIT(0) + +struct clk *clk_register_gate(struct device *dev, const char *name, + const char *parent_name, unsigned long flags, + void __iomem *reg, u8 bit_idx, + u8 clk_gate_flags, spinlock_t *lock); + +/** + * struct clk_divider - adjustable divider clock + * + * @hw: handle between common and hardware-specific interfaces + * @reg: register containing the divider + * @shift: shift to the divider bit field + * @width: width of the divider bit field + * @lock: register lock + * + * Clock with an adjustable divider affecting its output frequency. Implements + * .recalc_rate, .set_rate and .round_rate + * + * Flags: + * CLK_DIVIDER_ONE_BASED - by default the divisor is the value read from the + * register plus one. If CLK_DIVIDER_ONE_BASED is set then the divider is + * the raw value read from the register, with the value of zero considered + * invalid + * CLK_DIVIDER_POWER_OF_TWO - clock divisor is 2 raised to the value read from + * the hardware register + */ +struct clk_divider { + struct clk_hw hw; + void __iomem *reg; + u8 shift; + u8 width; + u8 flags; + spinlock_t *lock; + char *parent[1]; +}; + +#define CLK_DIVIDER_ONE_BASED BIT(0) +#define CLK_DIVIDER_POWER_OF_TWO BIT(1) + +struct clk *clk_register_divider(struct device *dev, const char *name, + const char *parent_name, unsigned long flags, + void __iomem *reg, u8 shift, u8 width, + u8 clk_divider_flags, spinlock_t *lock); + +/** + * struct clk_mux - multiplexer clock + * + * @hw: handle between common and hardware-specific interfaces + * @reg: register controlling multiplexer + * @shift: shift to multiplexer bit field + * @width: width of mutliplexer bit field + * @num_clks: number of parent clocks + * @lock: register lock + * + * Clock with multiple selectable parents. Implements .get_parent, .set_parent + * and .recalc_rate + * + * Flags: + * CLK_MUX_INDEX_ONE - register index starts at 1, not 0 + * CLK_MUX_INDEX_BITWISE - register index is a single bit (power of two) + */ +struct clk_mux { + struct clk_hw hw; + void __iomem *reg; + u8 shift; + u8 width; + u8 flags; + spinlock_t *lock; +}; + +#define CLK_MUX_INDEX_ONE BIT(0) +#define CLK_MUX_INDEX_BIT BIT(1) + +struct clk *clk_register_mux(struct device *dev, const char *name, + char **parent_names, u8 num_parents, unsigned long flags, + void __iomem *reg, u8 shift, u8 width, + u8 clk_mux_flags, spinlock_t *lock); + +/** + * clk_register - allocate a new clock, register it and return an opaque cookie + * @dev: device that is registering this clock + * @name: clock name + * @ops: operations this clock supports + * @hw: link to hardware-specific clock data + * @parent_names: array of string names for all possible parents + * @num_parents: number of possible parents + * @flags: framework-level hints and quirks + * + * clk_register is the primary interface for populating the clock tree with new + * clock nodes. It returns a pointer to the newly allocated struct clk which + * cannot be dereferenced by driver code but may be used in conjuction with the + * rest of the clock API. + */ +struct clk *clk_register(struct device *dev, const char *name, + const struct clk_ops *ops, struct clk_hw *hw, + char **parent_names, u8 num_parents, unsigned long flags); + +/* helper functions */ +const char *__clk_get_name(struct clk *clk); +struct clk_hw *__clk_get_hw(struct clk *clk); +u8 __clk_get_num_parents(struct clk *clk); +struct clk *__clk_get_parent(struct clk *clk); +inline int __clk_get_enable_count(struct clk *clk); +inline int __clk_get_prepare_count(struct clk *clk); +unsigned long __clk_get_rate(struct clk *clk); +unsigned long __clk_get_flags(struct clk *clk); +int __clk_is_enabled(struct clk *clk); +struct clk *__clk_lookup(const char *name); + +/* + * FIXME clock api without lock protection + */ +int __clk_prepare(struct clk *clk); +void __clk_unprepare(struct clk *clk); +void __clk_reparent(struct clk *clk, struct clk *new_parent); +unsigned long __clk_round_rate(struct clk *clk, unsigned long rate); + +#endif /* CONFIG_COMMON_CLK */ +#endif /* CLK_PROVIDER_H */ diff --git a/include/linux/clk.h b/include/linux/clk.h index b9d46fa154b..b0252726df6 100644 --- a/include/linux/clk.h +++ b/include/linux/clk.h @@ -3,6 +3,7 @@ * * Copyright (C) 2004 ARM Limited. * Written by Deep Blue Solutions Limited. + * Copyright (C) 2011-2012 Linaro Ltd <mturquette@linaro.org> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -12,18 +13,75 @@ #define __LINUX_CLK_H #include <linux/kernel.h> +#include <linux/notifier.h> struct device; -/* - * The base API. +struct clk; + +#ifdef CONFIG_COMMON_CLK + +/** + * DOC: clk notifier callback types + * + * PRE_RATE_CHANGE - called immediately before the clk rate is changed, + * to indicate that the rate change will proceed. Drivers must + * immediately terminate any operations that will be affected by the + * rate change. Callbacks may either return NOTIFY_DONE or + * NOTIFY_STOP. + * + * ABORT_RATE_CHANGE: called if the rate change failed for some reason + * after PRE_RATE_CHANGE. In this case, all registered notifiers on + * the clk will be called with ABORT_RATE_CHANGE. Callbacks must + * always return NOTIFY_DONE. + * + * POST_RATE_CHANGE - called after the clk rate change has successfully + * completed. Callbacks must always return NOTIFY_DONE. + * */ +#define PRE_RATE_CHANGE BIT(0) +#define POST_RATE_CHANGE BIT(1) +#define ABORT_RATE_CHANGE BIT(2) +/** + * struct clk_notifier - associate a clk with a notifier + * @clk: struct clk * to associate the notifier with + * @notifier_head: a blocking_notifier_head for this clk + * @node: linked list pointers + * + * A list of struct clk_notifier is maintained by the notifier code. + * An entry is created whenever code registers the first notifier on a + * particular @clk. Future notifiers on that @clk are added to the + * @notifier_head. + */ +struct clk_notifier { + struct clk *clk; + struct srcu_notifier_head notifier_head; + struct list_head node; +}; -/* - * struct clk - an machine class defined object / cookie. +/** + * struct clk_notifier_data - rate data to pass to the notifier callback + * @clk: struct clk * being changed + * @old_rate: previous rate of this clk + * @new_rate: new rate of this clk + * + * For a pre-notifier, old_rate is the clk's rate before this rate + * change, and new_rate is what the rate will be in the future. For a + * post-notifier, old_rate and new_rate are both set to the clk's + * current rate (this was done to optimize the implementation). */ -struct clk; +struct clk_notifier_data { + struct clk *clk; + unsigned long old_rate; + unsigned long new_rate; +}; + +int clk_notifier_register(struct clk *clk, struct notifier_block *nb); + +int clk_notifier_unregister(struct clk *clk, struct notifier_block *nb); + +#endif /* !CONFIG_COMMON_CLK */ /** * clk_get - lookup and obtain a reference to a clock producer. diff --git a/include/linux/cnt32_to_63.h b/include/linux/cnt32_to_63.h index e3d8bf26e5e..aa629bce903 100644 --- a/include/linux/cnt32_to_63.h +++ b/include/linux/cnt32_to_63.h @@ -16,7 +16,6 @@ #include <linux/compiler.h> #include <linux/types.h> #include <asm/byteorder.h> -#include <asm/system.h> /* this is used only to give gcc a clue about good code generation */ union cnt32_to_63 { diff --git a/include/linux/compat.h b/include/linux/compat.h index 7e05fcee75a..5d46217f84a 100644 --- a/include/linux/compat.h +++ b/include/linux/compat.h @@ -19,6 +19,10 @@ #include <asm/siginfo.h> #include <asm/signal.h> +#ifndef COMPAT_USE_64BIT_TIME +#define COMPAT_USE_64BIT_TIME 0 +#endif + #define compat_jiffies_to_clock_t(x) \ (((unsigned long)(x) * COMPAT_USER_HZ) / HZ) @@ -83,10 +87,26 @@ typedef struct { compat_sigset_word sig[_COMPAT_NSIG_WORDS]; } compat_sigset_t; +/* + * These functions operate strictly on struct compat_time* + */ extern int get_compat_timespec(struct timespec *, const struct compat_timespec __user *); extern int put_compat_timespec(const struct timespec *, struct compat_timespec __user *); +extern int get_compat_timeval(struct timeval *, + const struct compat_timeval __user *); +extern int put_compat_timeval(const struct timeval *, + struct compat_timeval __user *); +/* + * These functions operate on 32- or 64-bit specs depending on + * COMPAT_USE_64BIT_TIME, hence the void user pointer arguments and the + * naming as compat_get/put_ rather than get/put_compat_. + */ +extern int compat_get_timespec(struct timespec *, const void __user *); +extern int compat_put_timespec(const struct timespec *, void __user *); +extern int compat_get_timeval(struct timeval *, const void __user *); +extern int compat_put_timeval(const struct timeval *, void __user *); struct compat_iovec { compat_uptr_t iov_base; @@ -224,6 +244,7 @@ struct compat_sysinfo; struct compat_sysctl_args; struct compat_kexec_segment; struct compat_mq_attr; +struct compat_msgbuf; extern void compat_exit_robust_list(struct task_struct *curr); @@ -234,13 +255,22 @@ asmlinkage long compat_sys_get_robust_list(int pid, compat_uptr_t __user *head_ptr, compat_size_t __user *len_ptr); +#ifdef CONFIG_ARCH_WANT_OLD_COMPAT_IPC long compat_sys_semctl(int first, int second, int third, void __user *uptr); long compat_sys_msgsnd(int first, int second, int third, void __user *uptr); long compat_sys_msgrcv(int first, int second, int msgtyp, int third, int version, void __user *uptr); -long compat_sys_msgctl(int first, int second, void __user *uptr); long compat_sys_shmat(int first, int second, compat_uptr_t third, int version, void __user *uptr); +#else +long compat_sys_semctl(int semid, int semnum, int cmd, int arg); +long compat_sys_msgsnd(int msqid, struct compat_msgbuf __user *msgp, + size_t msgsz, int msgflg); +long compat_sys_msgrcv(int msqid, struct compat_msgbuf __user *msgp, + size_t msgsz, long msgtyp, int msgflg); +long compat_sys_shmat(int shmid, compat_uptr_t shmaddr, int shmflg); +#endif +long compat_sys_msgctl(int first, int second, void __user *uptr); long compat_sys_shmctl(int first, int second, void __user *uptr); long compat_sys_semtimedop(int semid, struct sembuf __user *tsems, unsigned nsems, const struct compat_timespec __user *timeout); diff --git a/include/linux/cpuidle.h b/include/linux/cpuidle.h index 712abcc205a..6c26a3da0e0 100644 --- a/include/linux/cpuidle.h +++ b/include/linux/cpuidle.h @@ -15,6 +15,7 @@ #include <linux/list.h> #include <linux/kobject.h> #include <linux/completion.h> +#include <linux/hrtimer.h> #define CPUIDLE_STATE_MAX 8 #define CPUIDLE_NAME_LEN 16 @@ -43,12 +44,15 @@ struct cpuidle_state { unsigned int flags; unsigned int exit_latency; /* in US */ - unsigned int power_usage; /* in mW */ + int power_usage; /* in mW */ unsigned int target_residency; /* in US */ + unsigned int disable; int (*enter) (struct cpuidle_device *dev, struct cpuidle_driver *drv, int index); + + int (*enter_dead) (struct cpuidle_device *dev, int index); }; /* Idle State Flags */ @@ -96,7 +100,6 @@ struct cpuidle_device { struct list_head device_list; struct kobject kobj; struct completion kobj_unregister; - void *governor_data; }; DECLARE_PER_CPU(struct cpuidle_device *, cpuidle_devices); @@ -118,10 +121,12 @@ static inline int cpuidle_get_last_residency(struct cpuidle_device *dev) ****************************/ struct cpuidle_driver { - char name[CPUIDLE_NAME_LEN]; + const char *name; struct module *owner; unsigned int power_specified:1; + /* set to 1 to use the core cpuidle time keeping (for all states). */ + unsigned int en_core_tk_irqen:1; struct cpuidle_state states[CPUIDLE_STATE_MAX]; int state_count; int safe_state_index; @@ -140,6 +145,11 @@ extern void cpuidle_pause_and_lock(void); extern void cpuidle_resume_and_unlock(void); extern int cpuidle_enable_device(struct cpuidle_device *dev); extern void cpuidle_disable_device(struct cpuidle_device *dev); +extern int cpuidle_wrap_enter(struct cpuidle_device *dev, + struct cpuidle_driver *drv, int index, + int (*enter)(struct cpuidle_device *dev, + struct cpuidle_driver *drv, int index)); +extern int cpuidle_play_dead(void); #else static inline void disable_cpuidle(void) { } @@ -157,6 +167,12 @@ static inline void cpuidle_resume_and_unlock(void) { } static inline int cpuidle_enable_device(struct cpuidle_device *dev) {return -ENODEV; } static inline void cpuidle_disable_device(struct cpuidle_device *dev) { } +static inline int cpuidle_wrap_enter(struct cpuidle_device *dev, + struct cpuidle_driver *drv, int index, + int (*enter)(struct cpuidle_device *dev, + struct cpuidle_driver *drv, int index)) +{ return -ENODEV; } +static inline int cpuidle_play_dead(void) {return -ENODEV; } #endif diff --git a/include/linux/cpumask.h b/include/linux/cpumask.h index 7b9b75a529b..a2c819d3c96 100644 --- a/include/linux/cpumask.h +++ b/include/linux/cpumask.h @@ -764,12 +764,6 @@ static inline const struct cpumask *get_cpu_mask(unsigned int cpu) * */ #ifndef CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS -/* These strip const, as traditionally they weren't const. */ -#define cpu_possible_map (*(cpumask_t *)cpu_possible_mask) -#define cpu_online_map (*(cpumask_t *)cpu_online_mask) -#define cpu_present_map (*(cpumask_t *)cpu_present_mask) -#define cpu_active_map (*(cpumask_t *)cpu_active_mask) - #define cpumask_of_cpu(cpu) (*get_cpu_mask(cpu)) #define CPU_MASK_LAST_WORD BITMAP_LAST_WORD_MASK(NR_CPUS) @@ -810,11 +804,10 @@ static inline const struct cpumask *get_cpu_mask(unsigned int cpu) #else /* NR_CPUS > 1 */ int __first_cpu(const cpumask_t *srcp); int __next_cpu(int n, const cpumask_t *srcp); -int __any_online_cpu(const cpumask_t *mask); #define first_cpu(src) __first_cpu(&(src)) #define next_cpu(n, src) __next_cpu((n), &(src)) -#define any_online_cpu(mask) __any_online_cpu(&(mask)) +#define any_online_cpu(mask) cpumask_any_and(&mask, cpu_online_mask) #define for_each_cpu_mask(cpu, mask) \ for ((cpu) = -1; \ (cpu) = next_cpu((cpu), (mask)), \ diff --git a/include/linux/cpuset.h b/include/linux/cpuset.h index 7a7e5fd2a27..668f66baac7 100644 --- a/include/linux/cpuset.h +++ b/include/linux/cpuset.h @@ -22,7 +22,7 @@ extern int cpuset_init(void); extern void cpuset_init_smp(void); extern void cpuset_update_active_cpus(void); extern void cpuset_cpus_allowed(struct task_struct *p, struct cpumask *mask); -extern int cpuset_cpus_allowed_fallback(struct task_struct *p); +extern void cpuset_cpus_allowed_fallback(struct task_struct *p); extern nodemask_t cpuset_mems_allowed(struct task_struct *p); #define cpuset_current_mems_allowed (current->mems_allowed) void cpuset_init_current_mems_allowed(void); @@ -135,10 +135,8 @@ static inline void cpuset_cpus_allowed(struct task_struct *p, cpumask_copy(mask, cpu_possible_mask); } -static inline int cpuset_cpus_allowed_fallback(struct task_struct *p) +static inline void cpuset_cpus_allowed_fallback(struct task_struct *p) { - do_set_cpus_allowed(p, cpu_possible_mask); - return cpumask_any(cpu_active_mask); } static inline nodemask_t cpuset_mems_allowed(struct task_struct *p) diff --git a/include/linux/cryptouser.h b/include/linux/cryptouser.h index 532fb58f16b..4abf2ea6a88 100644 --- a/include/linux/cryptouser.h +++ b/include/linux/cryptouser.h @@ -100,3 +100,6 @@ struct crypto_report_rng { char type[CRYPTO_MAX_NAME]; unsigned int seedsize; }; + +#define CRYPTO_REPORT_MAXSIZE (sizeof(struct crypto_user_alg) + \ + sizeof(struct crypto_report_blkcipher)) diff --git a/include/linux/debug_locks.h b/include/linux/debug_locks.h index 94f20c1488a..3bd46f76675 100644 --- a/include/linux/debug_locks.h +++ b/include/linux/debug_locks.h @@ -4,7 +4,6 @@ #include <linux/kernel.h> #include <linux/atomic.h> #include <linux/bug.h> -#include <asm/system.h> struct task_struct; diff --git a/include/linux/dma-buf.h b/include/linux/dma-buf.h index 887dcd48706..3efbfc2145c 100644 --- a/include/linux/dma-buf.h +++ b/include/linux/dma-buf.h @@ -29,6 +29,7 @@ #include <linux/scatterlist.h> #include <linux/list.h> #include <linux/dma-mapping.h> +#include <linux/fs.h> struct device; struct dma_buf; @@ -49,6 +50,17 @@ struct dma_buf_attachment; * @unmap_dma_buf: decreases usecount of buffer, might deallocate scatter * pages. * @release: release this buffer; to be called after the last dma_buf_put. + * @begin_cpu_access: [optional] called before cpu access to invalidate cpu + * caches and allocate backing storage (if not yet done) + * respectively pin the objet into memory. + * @end_cpu_access: [optional] called after cpu access to flush cashes. + * @kmap_atomic: maps a page from the buffer into kernel address + * space, users may not block until the subsequent unmap call. + * This callback must not sleep. + * @kunmap_atomic: [optional] unmaps a atomically mapped page from the buffer. + * This Callback must not sleep. + * @kmap: maps a page from the buffer into kernel address space. + * @kunmap: [optional] unmaps a page from the buffer. */ struct dma_buf_ops { int (*attach)(struct dma_buf *, struct device *, @@ -63,7 +75,8 @@ struct dma_buf_ops { struct sg_table * (*map_dma_buf)(struct dma_buf_attachment *, enum dma_data_direction); void (*unmap_dma_buf)(struct dma_buf_attachment *, - struct sg_table *); + struct sg_table *, + enum dma_data_direction); /* TODO: Add try_map_dma_buf version, to return immed with -EBUSY * if the call would block. */ @@ -71,6 +84,14 @@ struct dma_buf_ops { /* after final dma_buf_put() */ void (*release)(struct dma_buf *); + int (*begin_cpu_access)(struct dma_buf *, size_t, size_t, + enum dma_data_direction); + void (*end_cpu_access)(struct dma_buf *, size_t, size_t, + enum dma_data_direction); + void *(*kmap_atomic)(struct dma_buf *, unsigned long); + void (*kunmap_atomic)(struct dma_buf *, unsigned long, void *); + void *(*kmap)(struct dma_buf *, unsigned long); + void (*kunmap)(struct dma_buf *, unsigned long, void *); }; /** @@ -86,7 +107,7 @@ struct dma_buf { struct file *file; struct list_head attachments; const struct dma_buf_ops *ops; - /* mutex to serialize list manipulation and other ops */ + /* mutex to serialize list manipulation and attach/detach */ struct mutex lock; void *priv; }; @@ -109,20 +130,43 @@ struct dma_buf_attachment { void *priv; }; +/** + * get_dma_buf - convenience wrapper for get_file. + * @dmabuf: [in] pointer to dma_buf + * + * Increments the reference count on the dma-buf, needed in case of drivers + * that either need to create additional references to the dmabuf on the + * kernel side. For example, an exporter that needs to keep a dmabuf ptr + * so that subsequent exports don't create a new dmabuf. + */ +static inline void get_dma_buf(struct dma_buf *dmabuf) +{ + get_file(dmabuf->file); +} + #ifdef CONFIG_DMA_SHARED_BUFFER struct dma_buf_attachment *dma_buf_attach(struct dma_buf *dmabuf, struct device *dev); void dma_buf_detach(struct dma_buf *dmabuf, struct dma_buf_attachment *dmabuf_attach); -struct dma_buf *dma_buf_export(void *priv, struct dma_buf_ops *ops, - size_t size, int flags); -int dma_buf_fd(struct dma_buf *dmabuf); +struct dma_buf *dma_buf_export(void *priv, const struct dma_buf_ops *ops, + size_t size, int flags); +int dma_buf_fd(struct dma_buf *dmabuf, int flags); struct dma_buf *dma_buf_get(int fd); void dma_buf_put(struct dma_buf *dmabuf); struct sg_table *dma_buf_map_attachment(struct dma_buf_attachment *, enum dma_data_direction); -void dma_buf_unmap_attachment(struct dma_buf_attachment *, struct sg_table *); +void dma_buf_unmap_attachment(struct dma_buf_attachment *, struct sg_table *, + enum dma_data_direction); +int dma_buf_begin_cpu_access(struct dma_buf *dma_buf, size_t start, size_t len, + enum dma_data_direction dir); +void dma_buf_end_cpu_access(struct dma_buf *dma_buf, size_t start, size_t len, + enum dma_data_direction dir); +void *dma_buf_kmap_atomic(struct dma_buf *, unsigned long); +void dma_buf_kunmap_atomic(struct dma_buf *, unsigned long, void *); +void *dma_buf_kmap(struct dma_buf *, unsigned long); +void dma_buf_kunmap(struct dma_buf *, unsigned long, void *); #else static inline struct dma_buf_attachment *dma_buf_attach(struct dma_buf *dmabuf, @@ -138,13 +182,13 @@ static inline void dma_buf_detach(struct dma_buf *dmabuf, } static inline struct dma_buf *dma_buf_export(void *priv, - struct dma_buf_ops *ops, - size_t size, int flags) + const struct dma_buf_ops *ops, + size_t size, int flags) { return ERR_PTR(-ENODEV); } -static inline int dma_buf_fd(struct dma_buf *dmabuf) +static inline int dma_buf_fd(struct dma_buf *dmabuf, int flags) { return -ENODEV; } @@ -166,11 +210,44 @@ static inline struct sg_table *dma_buf_map_attachment( } static inline void dma_buf_unmap_attachment(struct dma_buf_attachment *attach, - struct sg_table *sg) + struct sg_table *sg, enum dma_data_direction dir) { return; } +static inline int dma_buf_begin_cpu_access(struct dma_buf *dmabuf, + size_t start, size_t len, + enum dma_data_direction dir) +{ + return -ENODEV; +} + +static inline void dma_buf_end_cpu_access(struct dma_buf *dmabuf, + size_t start, size_t len, + enum dma_data_direction dir) +{ +} + +static inline void *dma_buf_kmap_atomic(struct dma_buf *dmabuf, + unsigned long pnum) +{ + return NULL; +} + +static inline void dma_buf_kunmap_atomic(struct dma_buf *dmabuf, + unsigned long pnum, void *vaddr) +{ +} + +static inline void *dma_buf_kmap(struct dma_buf *dmabuf, unsigned long pnum) +{ + return NULL; +} + +static inline void dma_buf_kunmap(struct dma_buf *dmabuf, + unsigned long pnum, void *vaddr) +{ +} #endif /* CONFIG_DMA_SHARED_BUFFER */ #endif /* __DMA_BUF_H__ */ diff --git a/include/linux/dma-mapping.h b/include/linux/dma-mapping.h index e13117cbd2f..5a736af3cc7 100644 --- a/include/linux/dma-mapping.h +++ b/include/linux/dma-mapping.h @@ -77,7 +77,7 @@ static inline u64 dma_get_mask(struct device *dev) return DMA_BIT_MASK(32); } -#ifdef ARCH_HAS_DMA_SET_COHERENT_MASK +#ifdef CONFIG_ARCH_HAS_DMA_SET_COHERENT_MASK int dma_set_coherent_mask(struct device *dev, u64 mask); #else static inline int dma_set_coherent_mask(struct device *dev, u64 mask) diff --git a/include/linux/dmaengine.h b/include/linux/dmaengine.h index a5966f691ef..676f967390a 100644 --- a/include/linux/dmaengine.h +++ b/include/linux/dmaengine.h @@ -18,14 +18,15 @@ * The full GNU General Public License is included in this distribution in the * file called COPYING. */ -#ifndef DMAENGINE_H -#define DMAENGINE_H +#ifndef LINUX_DMAENGINE_H +#define LINUX_DMAENGINE_H #include <linux/device.h> #include <linux/uio.h> #include <linux/bug.h> #include <linux/scatterlist.h> #include <linux/bitmap.h> +#include <linux/types.h> #include <asm/page.h> /** @@ -258,6 +259,7 @@ struct dma_chan_percpu { * struct dma_chan - devices supply DMA channels, clients use them * @device: ptr to the dma device who supplies this channel, always !%NULL * @cookie: last cookie value returned to client + * @completed_cookie: last completed cookie for this channel * @chan_id: channel ID for sysfs * @dev: class device for sysfs * @device_node: used to add this to the device chan list @@ -269,6 +271,7 @@ struct dma_chan_percpu { struct dma_chan { struct dma_device *device; dma_cookie_t cookie; + dma_cookie_t completed_cookie; /* sysfs */ int chan_id; @@ -332,6 +335,9 @@ enum dma_slave_buswidth { * may or may not be applicable on memory sources. * @dst_maxburst: same as src_maxburst but for destination target * mutatis mutandis. + * @device_fc: Flow Controller Settings. Only valid for slave channels. Fill + * with 'true' if peripheral should be flow controller. Direction will be + * selected at Runtime. * * This struct is passed in as configuration data to a DMA engine * in order to set up a certain channel for DMA transport at runtime. @@ -358,6 +364,7 @@ struct dma_slave_config { enum dma_slave_buswidth dst_addr_width; u32 src_maxburst; u32 dst_maxburst; + bool device_fc; }; static inline const char *dma_chan_name(struct dma_chan *chan) @@ -576,10 +583,11 @@ struct dma_device { struct dma_async_tx_descriptor *(*device_prep_slave_sg)( struct dma_chan *chan, struct scatterlist *sgl, unsigned int sg_len, enum dma_transfer_direction direction, - unsigned long flags); + unsigned long flags, void *context); struct dma_async_tx_descriptor *(*device_prep_dma_cyclic)( struct dma_chan *chan, dma_addr_t buf_addr, size_t buf_len, - size_t period_len, enum dma_transfer_direction direction); + size_t period_len, enum dma_transfer_direction direction, + void *context); struct dma_async_tx_descriptor *(*device_prep_interleaved_dma)( struct dma_chan *chan, struct dma_interleaved_template *xt, unsigned long flags); @@ -613,7 +621,24 @@ static inline struct dma_async_tx_descriptor *dmaengine_prep_slave_single( struct scatterlist sg; sg_init_one(&sg, buf, len); - return chan->device->device_prep_slave_sg(chan, &sg, 1, dir, flags); + return chan->device->device_prep_slave_sg(chan, &sg, 1, + dir, flags, NULL); +} + +static inline struct dma_async_tx_descriptor *dmaengine_prep_slave_sg( + struct dma_chan *chan, struct scatterlist *sgl, unsigned int sg_len, + enum dma_transfer_direction dir, unsigned long flags) +{ + return chan->device->device_prep_slave_sg(chan, sgl, sg_len, + dir, flags, NULL); +} + +static inline struct dma_async_tx_descriptor *dmaengine_prep_dma_cyclic( + struct dma_chan *chan, dma_addr_t buf_addr, size_t buf_len, + size_t period_len, enum dma_transfer_direction dir) +{ + return chan->device->device_prep_dma_cyclic(chan, buf_addr, buf_len, + period_len, dir, NULL); } static inline int dmaengine_terminate_all(struct dma_chan *chan) diff --git a/include/linux/dw_dmac.h b/include/linux/dw_dmac.h index f2c64f92c4a..2412e02d7c0 100644 --- a/include/linux/dw_dmac.h +++ b/include/linux/dw_dmac.h @@ -31,18 +31,6 @@ struct dw_dma_platform_data { unsigned char chan_priority; }; -/** - * enum dw_dma_slave_width - DMA slave register access width. - * @DMA_SLAVE_WIDTH_8BIT: Do 8-bit slave register accesses - * @DMA_SLAVE_WIDTH_16BIT: Do 16-bit slave register accesses - * @DMA_SLAVE_WIDTH_32BIT: Do 32-bit slave register accesses - */ -enum dw_dma_slave_width { - DW_DMA_SLAVE_WIDTH_8BIT, - DW_DMA_SLAVE_WIDTH_16BIT, - DW_DMA_SLAVE_WIDTH_32BIT, -}; - /* bursts size */ enum dw_dma_msize { DW_DMA_MSIZE_1, @@ -55,47 +43,21 @@ enum dw_dma_msize { DW_DMA_MSIZE_256, }; -/* flow controller */ -enum dw_dma_fc { - DW_DMA_FC_D_M2M, - DW_DMA_FC_D_M2P, - DW_DMA_FC_D_P2M, - DW_DMA_FC_D_P2P, - DW_DMA_FC_P_P2M, - DW_DMA_FC_SP_P2P, - DW_DMA_FC_P_M2P, - DW_DMA_FC_DP_P2P, -}; - /** * struct dw_dma_slave - Controller-specific information about a slave * * @dma_dev: required DMA master device - * @tx_reg: physical address of data register used for - * memory-to-peripheral transfers - * @rx_reg: physical address of data register used for - * peripheral-to-memory transfers - * @reg_width: peripheral register width * @cfg_hi: Platform-specific initializer for the CFG_HI register * @cfg_lo: Platform-specific initializer for the CFG_LO register * @src_master: src master for transfers on allocated channel. * @dst_master: dest master for transfers on allocated channel. - * @src_msize: src burst size. - * @dst_msize: dest burst size. - * @fc: flow controller for DMA transfer */ struct dw_dma_slave { struct device *dma_dev; - dma_addr_t tx_reg; - dma_addr_t rx_reg; - enum dw_dma_slave_width reg_width; u32 cfg_hi; u32 cfg_lo; u8 src_master; u8 dst_master; - u8 src_msize; - u8 dst_msize; - u8 fc; }; /* Platform-configurable bits in CFG_HI */ diff --git a/include/linux/edac.h b/include/linux/edac.h index ba317e2930a..c621d762bb2 100644 --- a/include/linux/edac.h +++ b/include/linux/edac.h @@ -70,25 +70,64 @@ enum dev_type { #define DEV_FLAG_X32 BIT(DEV_X32) #define DEV_FLAG_X64 BIT(DEV_X64) -/* memory types */ +/** + * enum mem_type - memory types. For a more detailed reference, please see + * http://en.wikipedia.org/wiki/DRAM + * + * @MEM_EMPTY Empty csrow + * @MEM_RESERVED: Reserved csrow type + * @MEM_UNKNOWN: Unknown csrow type + * @MEM_FPM: FPM - Fast Page Mode, used on systems up to 1995. + * @MEM_EDO: EDO - Extended data out, used on systems up to 1998. + * @MEM_BEDO: BEDO - Burst Extended data out, an EDO variant. + * @MEM_SDR: SDR - Single data rate SDRAM + * http://en.wikipedia.org/wiki/Synchronous_dynamic_random-access_memory + * They use 3 pins for chip select: Pins 0 and 2 are + * for rank 0; pins 1 and 3 are for rank 1, if the memory + * is dual-rank. + * @MEM_RDR: Registered SDR SDRAM + * @MEM_DDR: Double data rate SDRAM + * http://en.wikipedia.org/wiki/DDR_SDRAM + * @MEM_RDDR: Registered Double data rate SDRAM + * This is a variant of the DDR memories. + * A registered memory has a buffer inside it, hiding + * part of the memory details to the memory controller. + * @MEM_RMBS: Rambus DRAM, used on a few Pentium III/IV controllers. + * @MEM_DDR2: DDR2 RAM, as described at JEDEC JESD79-2F. + * Those memories are labed as "PC2-" instead of "PC" to + * differenciate from DDR. + * @MEM_FB_DDR2: Fully-Buffered DDR2, as described at JEDEC Std No. 205 + * and JESD206. + * Those memories are accessed per DIMM slot, and not by + * a chip select signal. + * @MEM_RDDR2: Registered DDR2 RAM + * This is a variant of the DDR2 memories. + * @MEM_XDR: Rambus XDR + * It is an evolution of the original RAMBUS memories, + * created to compete with DDR2. Weren't used on any + * x86 arch, but cell_edac PPC memory controller uses it. + * @MEM_DDR3: DDR3 RAM + * @MEM_RDDR3: Registered DDR3 RAM + * This is a variant of the DDR3 memories. + */ enum mem_type { - MEM_EMPTY = 0, /* Empty csrow */ - MEM_RESERVED, /* Reserved csrow type */ - MEM_UNKNOWN, /* Unknown csrow type */ - MEM_FPM, /* Fast page mode */ - MEM_EDO, /* Extended data out */ - MEM_BEDO, /* Burst Extended data out */ - MEM_SDR, /* Single data rate SDRAM */ - MEM_RDR, /* Registered single data rate SDRAM */ - MEM_DDR, /* Double data rate SDRAM */ - MEM_RDDR, /* Registered Double data rate SDRAM */ - MEM_RMBS, /* Rambus DRAM */ - MEM_DDR2, /* DDR2 RAM */ - MEM_FB_DDR2, /* fully buffered DDR2 */ - MEM_RDDR2, /* Registered DDR2 RAM */ - MEM_XDR, /* Rambus XDR */ - MEM_DDR3, /* DDR3 RAM */ - MEM_RDDR3, /* Registered DDR3 RAM */ + MEM_EMPTY = 0, + MEM_RESERVED, + MEM_UNKNOWN, + MEM_FPM, + MEM_EDO, + MEM_BEDO, + MEM_SDR, + MEM_RDR, + MEM_DDR, + MEM_RDDR, + MEM_RMBS, + MEM_DDR2, + MEM_FB_DDR2, + MEM_RDDR2, + MEM_XDR, + MEM_DDR3, + MEM_RDDR3, }; #define MEM_FLAG_EMPTY BIT(MEM_EMPTY) @@ -166,8 +205,9 @@ enum scrub_type { #define OP_OFFLINE 0x300 /* - * There are several things to be aware of that aren't at all obvious: + * Concepts used at the EDAC subsystem * + * There are several things to be aware of that aren't at all obvious: * * SOCKETS, SOCKET SETS, BANKS, ROWS, CHIP-SELECT ROWS, CHANNELS, etc.. * @@ -176,36 +216,61 @@ enum scrub_type { * creating a common ground for discussion, terms and their definitions * will be established. * - * Memory devices: The individual chip on a memory stick. These devices - * commonly output 4 and 8 bits each. Grouping several - * of these in parallel provides 64 bits which is common - * for a memory stick. + * Memory devices: The individual DRAM chips on a memory stick. These + * devices commonly output 4 and 8 bits each (x4, x8). + * Grouping several of these in parallel provides the + * number of bits that the memory controller expects: + * typically 72 bits, in order to provide 64 bits + + * 8 bits of ECC data. * * Memory Stick: A printed circuit board that aggregates multiple - * memory devices in parallel. This is the atomic - * memory component that is purchaseable by Joe consumer - * and loaded into a memory socket. + * memory devices in parallel. In general, this is the + * Field Replaceable Unit (FRU) which gets replaced, in + * the case of excessive errors. Most often it is also + * called DIMM (Dual Inline Memory Module). + * + * Memory Socket: A physical connector on the motherboard that accepts + * a single memory stick. Also called as "slot" on several + * datasheets. * - * Socket: A physical connector on the motherboard that accepts - * a single memory stick. + * Channel: A memory controller channel, responsible to communicate + * with a group of DIMMs. Each channel has its own + * independent control (command) and data bus, and can + * be used independently or grouped with other channels. * - * Channel: Set of memory devices on a memory stick that must be - * grouped in parallel with one or more additional - * channels from other memory sticks. This parallel - * grouping of the output from multiple channels are - * necessary for the smallest granularity of memory access. - * Some memory controllers are capable of single channel - - * which means that memory sticks can be loaded - * individually. Other memory controllers are only - * capable of dual channel - which means that memory - * sticks must be loaded as pairs (see "socket set"). + * Branch: It is typically the highest hierarchy on a + * Fully-Buffered DIMM memory controller. + * Typically, it contains two channels. + * Two channels at the same branch can be used in single + * mode or in lockstep mode. + * When lockstep is enabled, the cacheline is doubled, + * but it generally brings some performance penalty. + * Also, it is generally not possible to point to just one + * memory stick when an error occurs, as the error + * correction code is calculated using two DIMMs instead + * of one. Due to that, it is capable of correcting more + * errors than on single mode. * - * Chip-select row: All of the memory devices that are selected together. - * for a single, minimum grain of memory access. - * This selects all of the parallel memory devices across - * all of the parallel channels. Common chip-select rows - * for single channel are 64 bits, for dual channel 128 - * bits. + * Single-channel: The data accessed by the memory controller is contained + * into one dimm only. E. g. if the data is 64 bits-wide, + * the data flows to the CPU using one 64 bits parallel + * access. + * Typically used with SDR, DDR, DDR2 and DDR3 memories. + * FB-DIMM and RAMBUS use a different concept for channel, + * so this concept doesn't apply there. + * + * Double-channel: The data size accessed by the memory controller is + * interlaced into two dimms, accessed at the same time. + * E. g. if the DIMM is 64 bits-wide (72 bits with ECC), + * the data flows to the CPU using a 128 bits parallel + * access. + * + * Chip-select row: This is the name of the DRAM signal used to select the + * DRAM ranks to be accessed. Common chip-select rows for + * single channel are 64 bits, for dual channel 128 bits. + * It may not be visible by the memory controller, as some + * DIMM types have a memory buffer that can hide direct + * access to it from the Memory Controller. * * Single-Ranked stick: A Single-ranked stick has 1 chip-select row of memory. * Motherboards commonly drive two chip-select pins to @@ -218,8 +283,8 @@ enum scrub_type { * * Double-sided stick: DEPRECATED TERM, see Double-Ranked stick. * A double-sided stick has two chip-select rows which - * access different sets of memory devices. The two - * rows cannot be accessed concurrently. "Double-sided" + * access different sets of memory devices. The two + * rows cannot be accessed concurrently. "Double-sided" * is irrespective of the memory devices being mounted * on both sides of the memory stick. * @@ -247,10 +312,22 @@ enum scrub_type { * PS - I enjoyed writing all that about as much as you enjoyed reading it. */ -struct channel_info { - int chan_idx; /* channel index */ - u32 ce_count; /* Correctable Errors for this CHANNEL */ - char label[EDAC_MC_LABEL_LEN + 1]; /* DIMM label on motherboard */ +/** + * struct rank_info - contains the information for one DIMM rank + * + * @chan_idx: channel number where the rank is (typically, 0 or 1) + * @ce_count: number of correctable errors for this rank + * @label: DIMM label. Different ranks for the same DIMM should be + * filled, on userspace, with the same label. + * FIXME: The core currently won't enforce it. + * @csrow: A pointer to the chip select row structure (the parent + * structure). The location of the rank is given by + * the (csrow->csrow_idx, chan_idx) vector. + */ +struct rank_info { + int chan_idx; + u32 ce_count; + char label[EDAC_MC_LABEL_LEN + 1]; struct csrow_info *csrow; /* the parent */ }; @@ -274,7 +351,7 @@ struct csrow_info { /* channel information for this csrow */ u32 nr_channels; - struct channel_info *channels; + struct rank_info *channels; }; struct mcidev_sysfs_group { diff --git a/include/linux/efi.h b/include/linux/efi.h index 47fbf6b3dc7..88ec80670d5 100644 --- a/include/linux/efi.h +++ b/include/linux/efi.h @@ -22,7 +22,6 @@ #include <linux/pstore.h> #include <asm/page.h> -#include <asm/system.h> #define EFI_SUCCESS 0 #define EFI_LOAD_ERROR ( 1 | (1UL << (BITS_PER_LONG-1))) diff --git a/include/linux/ext2_fs.h b/include/linux/ext2_fs.h index ce1b719e8bd..2723e715f67 100644 --- a/include/linux/ext2_fs.h +++ b/include/linux/ext2_fs.h @@ -18,574 +18,25 @@ #include <linux/types.h> #include <linux/magic.h> -#include <linux/fs.h> -/* - * The second extended filesystem constants/structures - */ - -/* - * Define EXT2FS_DEBUG to produce debug messages - */ -#undef EXT2FS_DEBUG - -/* - * Define EXT2_RESERVATION to reserve data blocks for expanding files - */ -#define EXT2_DEFAULT_RESERVE_BLOCKS 8 -/*max window size: 1024(direct blocks) + 3([t,d]indirect blocks) */ -#define EXT2_MAX_RESERVE_BLOCKS 1027 -#define EXT2_RESERVE_WINDOW_NOT_ALLOCATED 0 -/* - * The second extended file system version - */ -#define EXT2FS_DATE "95/08/09" -#define EXT2FS_VERSION "0.5b" - -/* - * Debug code - */ -#ifdef EXT2FS_DEBUG -# define ext2_debug(f, a...) { \ - printk ("EXT2-fs DEBUG (%s, %d): %s:", \ - __FILE__, __LINE__, __func__); \ - printk (f, ## a); \ - } -#else -# define ext2_debug(f, a...) /**/ -#endif - -/* - * Special inode numbers - */ -#define EXT2_BAD_INO 1 /* Bad blocks inode */ -#define EXT2_ROOT_INO 2 /* Root inode */ -#define EXT2_BOOT_LOADER_INO 5 /* Boot loader inode */ -#define EXT2_UNDEL_DIR_INO 6 /* Undelete directory inode */ - -/* First non-reserved inode for old ext2 filesystems */ -#define EXT2_GOOD_OLD_FIRST_INO 11 - -#ifdef __KERNEL__ -#include <linux/ext2_fs_sb.h> -static inline struct ext2_sb_info *EXT2_SB(struct super_block *sb) -{ - return sb->s_fs_info; -} -#else -/* Assume that user mode programs are passing in an ext2fs superblock, not - * a kernel struct super_block. This will allow us to call the feature-test - * macros from user land. */ -#define EXT2_SB(sb) (sb) -#endif +#define EXT2_NAME_LEN 255 /* * Maximal count of links to a file */ #define EXT2_LINK_MAX 32000 -/* - * Macro-instructions used to manage several block sizes - */ -#define EXT2_MIN_BLOCK_SIZE 1024 -#define EXT2_MAX_BLOCK_SIZE 4096 -#define EXT2_MIN_BLOCK_LOG_SIZE 10 -#ifdef __KERNEL__ -# define EXT2_BLOCK_SIZE(s) ((s)->s_blocksize) -#else -# define EXT2_BLOCK_SIZE(s) (EXT2_MIN_BLOCK_SIZE << (s)->s_log_block_size) -#endif -#define EXT2_ADDR_PER_BLOCK(s) (EXT2_BLOCK_SIZE(s) / sizeof (__u32)) -#ifdef __KERNEL__ -# define EXT2_BLOCK_SIZE_BITS(s) ((s)->s_blocksize_bits) -#else -# define EXT2_BLOCK_SIZE_BITS(s) ((s)->s_log_block_size + 10) -#endif -#ifdef __KERNEL__ -#define EXT2_ADDR_PER_BLOCK_BITS(s) (EXT2_SB(s)->s_addr_per_block_bits) -#define EXT2_INODE_SIZE(s) (EXT2_SB(s)->s_inode_size) -#define EXT2_FIRST_INO(s) (EXT2_SB(s)->s_first_ino) -#else -#define EXT2_INODE_SIZE(s) (((s)->s_rev_level == EXT2_GOOD_OLD_REV) ? \ - EXT2_GOOD_OLD_INODE_SIZE : \ - (s)->s_inode_size) -#define EXT2_FIRST_INO(s) (((s)->s_rev_level == EXT2_GOOD_OLD_REV) ? \ - EXT2_GOOD_OLD_FIRST_INO : \ - (s)->s_first_ino) -#endif +#define EXT2_SB_MAGIC_OFFSET 0x38 +#define EXT2_SB_BLOCKS_OFFSET 0x04 +#define EXT2_SB_BSIZE_OFFSET 0x18 -/* - * Macro-instructions used to manage fragments - */ -#define EXT2_MIN_FRAG_SIZE 1024 -#define EXT2_MAX_FRAG_SIZE 4096 -#define EXT2_MIN_FRAG_LOG_SIZE 10 -#ifdef __KERNEL__ -# define EXT2_FRAG_SIZE(s) (EXT2_SB(s)->s_frag_size) -# define EXT2_FRAGS_PER_BLOCK(s) (EXT2_SB(s)->s_frags_per_block) -#else -# define EXT2_FRAG_SIZE(s) (EXT2_MIN_FRAG_SIZE << (s)->s_log_frag_size) -# define EXT2_FRAGS_PER_BLOCK(s) (EXT2_BLOCK_SIZE(s) / EXT2_FRAG_SIZE(s)) -#endif - -/* - * Structure of a blocks group descriptor - */ -struct ext2_group_desc +static inline u64 ext2_image_size(void *ext2_sb) { - __le32 bg_block_bitmap; /* Blocks bitmap block */ - __le32 bg_inode_bitmap; /* Inodes bitmap block */ - __le32 bg_inode_table; /* Inodes table block */ - __le16 bg_free_blocks_count; /* Free blocks count */ - __le16 bg_free_inodes_count; /* Free inodes count */ - __le16 bg_used_dirs_count; /* Directories count */ - __le16 bg_pad; - __le32 bg_reserved[3]; -}; - -/* - * Macro-instructions used to manage group descriptors - */ -#ifdef __KERNEL__ -# define EXT2_BLOCKS_PER_GROUP(s) (EXT2_SB(s)->s_blocks_per_group) -# define EXT2_DESC_PER_BLOCK(s) (EXT2_SB(s)->s_desc_per_block) -# define EXT2_INODES_PER_GROUP(s) (EXT2_SB(s)->s_inodes_per_group) -# define EXT2_DESC_PER_BLOCK_BITS(s) (EXT2_SB(s)->s_desc_per_block_bits) -#else -# define EXT2_BLOCKS_PER_GROUP(s) ((s)->s_blocks_per_group) -# define EXT2_DESC_PER_BLOCK(s) (EXT2_BLOCK_SIZE(s) / sizeof (struct ext2_group_desc)) -# define EXT2_INODES_PER_GROUP(s) ((s)->s_inodes_per_group) -#endif - -/* - * Constants relative to the data blocks - */ -#define EXT2_NDIR_BLOCKS 12 -#define EXT2_IND_BLOCK EXT2_NDIR_BLOCKS -#define EXT2_DIND_BLOCK (EXT2_IND_BLOCK + 1) -#define EXT2_TIND_BLOCK (EXT2_DIND_BLOCK + 1) -#define EXT2_N_BLOCKS (EXT2_TIND_BLOCK + 1) - -/* - * Inode flags (GETFLAGS/SETFLAGS) - */ -#define EXT2_SECRM_FL FS_SECRM_FL /* Secure deletion */ -#define EXT2_UNRM_FL FS_UNRM_FL /* Undelete */ -#define EXT2_COMPR_FL FS_COMPR_FL /* Compress file */ -#define EXT2_SYNC_FL FS_SYNC_FL /* Synchronous updates */ -#define EXT2_IMMUTABLE_FL FS_IMMUTABLE_FL /* Immutable file */ -#define EXT2_APPEND_FL FS_APPEND_FL /* writes to file may only append */ -#define EXT2_NODUMP_FL FS_NODUMP_FL /* do not dump file */ -#define EXT2_NOATIME_FL FS_NOATIME_FL /* do not update atime */ -/* Reserved for compression usage... */ -#define EXT2_DIRTY_FL FS_DIRTY_FL -#define EXT2_COMPRBLK_FL FS_COMPRBLK_FL /* One or more compressed clusters */ -#define EXT2_NOCOMP_FL FS_NOCOMP_FL /* Don't compress */ -#define EXT2_ECOMPR_FL FS_ECOMPR_FL /* Compression error */ -/* End compression flags --- maybe not all used */ -#define EXT2_BTREE_FL FS_BTREE_FL /* btree format dir */ -#define EXT2_INDEX_FL FS_INDEX_FL /* hash-indexed directory */ -#define EXT2_IMAGIC_FL FS_IMAGIC_FL /* AFS directory */ -#define EXT2_JOURNAL_DATA_FL FS_JOURNAL_DATA_FL /* Reserved for ext3 */ -#define EXT2_NOTAIL_FL FS_NOTAIL_FL /* file tail should not be merged */ -#define EXT2_DIRSYNC_FL FS_DIRSYNC_FL /* dirsync behaviour (directories only) */ -#define EXT2_TOPDIR_FL FS_TOPDIR_FL /* Top of directory hierarchies*/ -#define EXT2_RESERVED_FL FS_RESERVED_FL /* reserved for ext2 lib */ - -#define EXT2_FL_USER_VISIBLE FS_FL_USER_VISIBLE /* User visible flags */ -#define EXT2_FL_USER_MODIFIABLE FS_FL_USER_MODIFIABLE /* User modifiable flags */ - -/* Flags that should be inherited by new inodes from their parent. */ -#define EXT2_FL_INHERITED (EXT2_SECRM_FL | EXT2_UNRM_FL | EXT2_COMPR_FL |\ - EXT2_SYNC_FL | EXT2_NODUMP_FL |\ - EXT2_NOATIME_FL | EXT2_COMPRBLK_FL |\ - EXT2_NOCOMP_FL | EXT2_JOURNAL_DATA_FL |\ - EXT2_NOTAIL_FL | EXT2_DIRSYNC_FL) - -/* Flags that are appropriate for regular files (all but dir-specific ones). */ -#define EXT2_REG_FLMASK (~(EXT2_DIRSYNC_FL | EXT2_TOPDIR_FL)) - -/* Flags that are appropriate for non-directories/regular files. */ -#define EXT2_OTHER_FLMASK (EXT2_NODUMP_FL | EXT2_NOATIME_FL) - -/* Mask out flags that are inappropriate for the given type of inode. */ -static inline __u32 ext2_mask_flags(umode_t mode, __u32 flags) -{ - if (S_ISDIR(mode)) - return flags; - else if (S_ISREG(mode)) - return flags & EXT2_REG_FLMASK; - else - return flags & EXT2_OTHER_FLMASK; + __u8 *p = ext2_sb; + if (*(__le16 *)(p + EXT2_SB_MAGIC_OFFSET) != cpu_to_le16(EXT2_SUPER_MAGIC)) + return 0; + return (u64)le32_to_cpup((__le32 *)(p + EXT2_SB_BLOCKS_OFFSET)) << + le32_to_cpup((__le32 *)(p + EXT2_SB_BSIZE_OFFSET)); } -/* - * ioctl commands - */ -#define EXT2_IOC_GETFLAGS FS_IOC_GETFLAGS -#define EXT2_IOC_SETFLAGS FS_IOC_SETFLAGS -#define EXT2_IOC_GETVERSION FS_IOC_GETVERSION -#define EXT2_IOC_SETVERSION FS_IOC_SETVERSION -#define EXT2_IOC_GETRSVSZ _IOR('f', 5, long) -#define EXT2_IOC_SETRSVSZ _IOW('f', 6, long) - -/* - * ioctl commands in 32 bit emulation - */ -#define EXT2_IOC32_GETFLAGS FS_IOC32_GETFLAGS -#define EXT2_IOC32_SETFLAGS FS_IOC32_SETFLAGS -#define EXT2_IOC32_GETVERSION FS_IOC32_GETVERSION -#define EXT2_IOC32_SETVERSION FS_IOC32_SETVERSION - -/* - * Structure of an inode on the disk - */ -struct ext2_inode { - __le16 i_mode; /* File mode */ - __le16 i_uid; /* Low 16 bits of Owner Uid */ - __le32 i_size; /* Size in bytes */ - __le32 i_atime; /* Access time */ - __le32 i_ctime; /* Creation time */ - __le32 i_mtime; /* Modification time */ - __le32 i_dtime; /* Deletion Time */ - __le16 i_gid; /* Low 16 bits of Group Id */ - __le16 i_links_count; /* Links count */ - __le32 i_blocks; /* Blocks count */ - __le32 i_flags; /* File flags */ - union { - struct { - __le32 l_i_reserved1; - } linux1; - struct { - __le32 h_i_translator; - } hurd1; - struct { - __le32 m_i_reserved1; - } masix1; - } osd1; /* OS dependent 1 */ - __le32 i_block[EXT2_N_BLOCKS];/* Pointers to blocks */ - __le32 i_generation; /* File version (for NFS) */ - __le32 i_file_acl; /* File ACL */ - __le32 i_dir_acl; /* Directory ACL */ - __le32 i_faddr; /* Fragment address */ - union { - struct { - __u8 l_i_frag; /* Fragment number */ - __u8 l_i_fsize; /* Fragment size */ - __u16 i_pad1; - __le16 l_i_uid_high; /* these 2 fields */ - __le16 l_i_gid_high; /* were reserved2[0] */ - __u32 l_i_reserved2; - } linux2; - struct { - __u8 h_i_frag; /* Fragment number */ - __u8 h_i_fsize; /* Fragment size */ - __le16 h_i_mode_high; - __le16 h_i_uid_high; - __le16 h_i_gid_high; - __le32 h_i_author; - } hurd2; - struct { - __u8 m_i_frag; /* Fragment number */ - __u8 m_i_fsize; /* Fragment size */ - __u16 m_pad1; - __u32 m_i_reserved2[2]; - } masix2; - } osd2; /* OS dependent 2 */ -}; - -#define i_size_high i_dir_acl - -#if defined(__KERNEL__) || defined(__linux__) -#define i_reserved1 osd1.linux1.l_i_reserved1 -#define i_frag osd2.linux2.l_i_frag -#define i_fsize osd2.linux2.l_i_fsize -#define i_uid_low i_uid -#define i_gid_low i_gid -#define i_uid_high osd2.linux2.l_i_uid_high -#define i_gid_high osd2.linux2.l_i_gid_high -#define i_reserved2 osd2.linux2.l_i_reserved2 -#endif - -#ifdef __hurd__ -#define i_translator osd1.hurd1.h_i_translator -#define i_frag osd2.hurd2.h_i_frag -#define i_fsize osd2.hurd2.h_i_fsize -#define i_uid_high osd2.hurd2.h_i_uid_high -#define i_gid_high osd2.hurd2.h_i_gid_high -#define i_author osd2.hurd2.h_i_author -#endif - -#ifdef __masix__ -#define i_reserved1 osd1.masix1.m_i_reserved1 -#define i_frag osd2.masix2.m_i_frag -#define i_fsize osd2.masix2.m_i_fsize -#define i_reserved2 osd2.masix2.m_i_reserved2 -#endif - -/* - * File system states - */ -#define EXT2_VALID_FS 0x0001 /* Unmounted cleanly */ -#define EXT2_ERROR_FS 0x0002 /* Errors detected */ - -/* - * Mount flags - */ -#define EXT2_MOUNT_CHECK 0x000001 /* Do mount-time checks */ -#define EXT2_MOUNT_OLDALLOC 0x000002 /* Don't use the new Orlov allocator */ -#define EXT2_MOUNT_GRPID 0x000004 /* Create files with directory's group */ -#define EXT2_MOUNT_DEBUG 0x000008 /* Some debugging messages */ -#define EXT2_MOUNT_ERRORS_CONT 0x000010 /* Continue on errors */ -#define EXT2_MOUNT_ERRORS_RO 0x000020 /* Remount fs ro on errors */ -#define EXT2_MOUNT_ERRORS_PANIC 0x000040 /* Panic on errors */ -#define EXT2_MOUNT_MINIX_DF 0x000080 /* Mimics the Minix statfs */ -#define EXT2_MOUNT_NOBH 0x000100 /* No buffer_heads */ -#define EXT2_MOUNT_NO_UID32 0x000200 /* Disable 32-bit UIDs */ -#define EXT2_MOUNT_XATTR_USER 0x004000 /* Extended user attributes */ -#define EXT2_MOUNT_POSIX_ACL 0x008000 /* POSIX Access Control Lists */ -#define EXT2_MOUNT_XIP 0x010000 /* Execute in place */ -#define EXT2_MOUNT_USRQUOTA 0x020000 /* user quota */ -#define EXT2_MOUNT_GRPQUOTA 0x040000 /* group quota */ -#define EXT2_MOUNT_RESERVATION 0x080000 /* Preallocation */ - - -#define clear_opt(o, opt) o &= ~EXT2_MOUNT_##opt -#define set_opt(o, opt) o |= EXT2_MOUNT_##opt -#define test_opt(sb, opt) (EXT2_SB(sb)->s_mount_opt & \ - EXT2_MOUNT_##opt) -/* - * Maximal mount counts between two filesystem checks - */ -#define EXT2_DFL_MAX_MNT_COUNT 20 /* Allow 20 mounts */ -#define EXT2_DFL_CHECKINTERVAL 0 /* Don't use interval check */ - -/* - * Behaviour when detecting errors - */ -#define EXT2_ERRORS_CONTINUE 1 /* Continue execution */ -#define EXT2_ERRORS_RO 2 /* Remount fs read-only */ -#define EXT2_ERRORS_PANIC 3 /* Panic */ -#define EXT2_ERRORS_DEFAULT EXT2_ERRORS_CONTINUE - -/* - * Structure of the super block - */ -struct ext2_super_block { - __le32 s_inodes_count; /* Inodes count */ - __le32 s_blocks_count; /* Blocks count */ - __le32 s_r_blocks_count; /* Reserved blocks count */ - __le32 s_free_blocks_count; /* Free blocks count */ - __le32 s_free_inodes_count; /* Free inodes count */ - __le32 s_first_data_block; /* First Data Block */ - __le32 s_log_block_size; /* Block size */ - __le32 s_log_frag_size; /* Fragment size */ - __le32 s_blocks_per_group; /* # Blocks per group */ - __le32 s_frags_per_group; /* # Fragments per group */ - __le32 s_inodes_per_group; /* # Inodes per group */ - __le32 s_mtime; /* Mount time */ - __le32 s_wtime; /* Write time */ - __le16 s_mnt_count; /* Mount count */ - __le16 s_max_mnt_count; /* Maximal mount count */ - __le16 s_magic; /* Magic signature */ - __le16 s_state; /* File system state */ - __le16 s_errors; /* Behaviour when detecting errors */ - __le16 s_minor_rev_level; /* minor revision level */ - __le32 s_lastcheck; /* time of last check */ - __le32 s_checkinterval; /* max. time between checks */ - __le32 s_creator_os; /* OS */ - __le32 s_rev_level; /* Revision level */ - __le16 s_def_resuid; /* Default uid for reserved blocks */ - __le16 s_def_resgid; /* Default gid for reserved blocks */ - /* - * These fields are for EXT2_DYNAMIC_REV superblocks only. - * - * Note: the difference between the compatible feature set and - * the incompatible feature set is that if there is a bit set - * in the incompatible feature set that the kernel doesn't - * know about, it should refuse to mount the filesystem. - * - * e2fsck's requirements are more strict; if it doesn't know - * about a feature in either the compatible or incompatible - * feature set, it must abort and not try to meddle with - * things it doesn't understand... - */ - __le32 s_first_ino; /* First non-reserved inode */ - __le16 s_inode_size; /* size of inode structure */ - __le16 s_block_group_nr; /* block group # of this superblock */ - __le32 s_feature_compat; /* compatible feature set */ - __le32 s_feature_incompat; /* incompatible feature set */ - __le32 s_feature_ro_compat; /* readonly-compatible feature set */ - __u8 s_uuid[16]; /* 128-bit uuid for volume */ - char s_volume_name[16]; /* volume name */ - char s_last_mounted[64]; /* directory where last mounted */ - __le32 s_algorithm_usage_bitmap; /* For compression */ - /* - * Performance hints. Directory preallocation should only - * happen if the EXT2_COMPAT_PREALLOC flag is on. - */ - __u8 s_prealloc_blocks; /* Nr of blocks to try to preallocate*/ - __u8 s_prealloc_dir_blocks; /* Nr to preallocate for dirs */ - __u16 s_padding1; - /* - * Journaling support valid if EXT3_FEATURE_COMPAT_HAS_JOURNAL set. - */ - __u8 s_journal_uuid[16]; /* uuid of journal superblock */ - __u32 s_journal_inum; /* inode number of journal file */ - __u32 s_journal_dev; /* device number of journal file */ - __u32 s_last_orphan; /* start of list of inodes to delete */ - __u32 s_hash_seed[4]; /* HTREE hash seed */ - __u8 s_def_hash_version; /* Default hash version to use */ - __u8 s_reserved_char_pad; - __u16 s_reserved_word_pad; - __le32 s_default_mount_opts; - __le32 s_first_meta_bg; /* First metablock block group */ - __u32 s_reserved[190]; /* Padding to the end of the block */ -}; - -/* - * Codes for operating systems - */ -#define EXT2_OS_LINUX 0 -#define EXT2_OS_HURD 1 -#define EXT2_OS_MASIX 2 -#define EXT2_OS_FREEBSD 3 -#define EXT2_OS_LITES 4 - -/* - * Revision levels - */ -#define EXT2_GOOD_OLD_REV 0 /* The good old (original) format */ -#define EXT2_DYNAMIC_REV 1 /* V2 format w/ dynamic inode sizes */ - -#define EXT2_CURRENT_REV EXT2_GOOD_OLD_REV -#define EXT2_MAX_SUPP_REV EXT2_DYNAMIC_REV - -#define EXT2_GOOD_OLD_INODE_SIZE 128 - -/* - * Feature set definitions - */ - -#define EXT2_HAS_COMPAT_FEATURE(sb,mask) \ - ( EXT2_SB(sb)->s_es->s_feature_compat & cpu_to_le32(mask) ) -#define EXT2_HAS_RO_COMPAT_FEATURE(sb,mask) \ - ( EXT2_SB(sb)->s_es->s_feature_ro_compat & cpu_to_le32(mask) ) -#define EXT2_HAS_INCOMPAT_FEATURE(sb,mask) \ - ( EXT2_SB(sb)->s_es->s_feature_incompat & cpu_to_le32(mask) ) -#define EXT2_SET_COMPAT_FEATURE(sb,mask) \ - EXT2_SB(sb)->s_es->s_feature_compat |= cpu_to_le32(mask) -#define EXT2_SET_RO_COMPAT_FEATURE(sb,mask) \ - EXT2_SB(sb)->s_es->s_feature_ro_compat |= cpu_to_le32(mask) -#define EXT2_SET_INCOMPAT_FEATURE(sb,mask) \ - EXT2_SB(sb)->s_es->s_feature_incompat |= cpu_to_le32(mask) -#define EXT2_CLEAR_COMPAT_FEATURE(sb,mask) \ - EXT2_SB(sb)->s_es->s_feature_compat &= ~cpu_to_le32(mask) -#define EXT2_CLEAR_RO_COMPAT_FEATURE(sb,mask) \ - EXT2_SB(sb)->s_es->s_feature_ro_compat &= ~cpu_to_le32(mask) -#define EXT2_CLEAR_INCOMPAT_FEATURE(sb,mask) \ - EXT2_SB(sb)->s_es->s_feature_incompat &= ~cpu_to_le32(mask) - -#define EXT2_FEATURE_COMPAT_DIR_PREALLOC 0x0001 -#define EXT2_FEATURE_COMPAT_IMAGIC_INODES 0x0002 -#define EXT3_FEATURE_COMPAT_HAS_JOURNAL 0x0004 -#define EXT2_FEATURE_COMPAT_EXT_ATTR 0x0008 -#define EXT2_FEATURE_COMPAT_RESIZE_INO 0x0010 -#define EXT2_FEATURE_COMPAT_DIR_INDEX 0x0020 -#define EXT2_FEATURE_COMPAT_ANY 0xffffffff - -#define EXT2_FEATURE_RO_COMPAT_SPARSE_SUPER 0x0001 -#define EXT2_FEATURE_RO_COMPAT_LARGE_FILE 0x0002 -#define EXT2_FEATURE_RO_COMPAT_BTREE_DIR 0x0004 -#define EXT2_FEATURE_RO_COMPAT_ANY 0xffffffff - -#define EXT2_FEATURE_INCOMPAT_COMPRESSION 0x0001 -#define EXT2_FEATURE_INCOMPAT_FILETYPE 0x0002 -#define EXT3_FEATURE_INCOMPAT_RECOVER 0x0004 -#define EXT3_FEATURE_INCOMPAT_JOURNAL_DEV 0x0008 -#define EXT2_FEATURE_INCOMPAT_META_BG 0x0010 -#define EXT2_FEATURE_INCOMPAT_ANY 0xffffffff - -#define EXT2_FEATURE_COMPAT_SUPP EXT2_FEATURE_COMPAT_EXT_ATTR -#define EXT2_FEATURE_INCOMPAT_SUPP (EXT2_FEATURE_INCOMPAT_FILETYPE| \ - EXT2_FEATURE_INCOMPAT_META_BG) -#define EXT2_FEATURE_RO_COMPAT_SUPP (EXT2_FEATURE_RO_COMPAT_SPARSE_SUPER| \ - EXT2_FEATURE_RO_COMPAT_LARGE_FILE| \ - EXT2_FEATURE_RO_COMPAT_BTREE_DIR) -#define EXT2_FEATURE_RO_COMPAT_UNSUPPORTED ~EXT2_FEATURE_RO_COMPAT_SUPP -#define EXT2_FEATURE_INCOMPAT_UNSUPPORTED ~EXT2_FEATURE_INCOMPAT_SUPP - -/* - * Default values for user and/or group using reserved blocks - */ -#define EXT2_DEF_RESUID 0 -#define EXT2_DEF_RESGID 0 - -/* - * Default mount options - */ -#define EXT2_DEFM_DEBUG 0x0001 -#define EXT2_DEFM_BSDGROUPS 0x0002 -#define EXT2_DEFM_XATTR_USER 0x0004 -#define EXT2_DEFM_ACL 0x0008 -#define EXT2_DEFM_UID16 0x0010 - /* Not used by ext2, but reserved for use by ext3 */ -#define EXT3_DEFM_JMODE 0x0060 -#define EXT3_DEFM_JMODE_DATA 0x0020 -#define EXT3_DEFM_JMODE_ORDERED 0x0040 -#define EXT3_DEFM_JMODE_WBACK 0x0060 - -/* - * Structure of a directory entry - */ -#define EXT2_NAME_LEN 255 - -struct ext2_dir_entry { - __le32 inode; /* Inode number */ - __le16 rec_len; /* Directory entry length */ - __le16 name_len; /* Name length */ - char name[EXT2_NAME_LEN]; /* File name */ -}; - -/* - * The new version of the directory entry. Since EXT2 structures are - * stored in intel byte order, and the name_len field could never be - * bigger than 255 chars, it's safe to reclaim the extra byte for the - * file_type field. - */ -struct ext2_dir_entry_2 { - __le32 inode; /* Inode number */ - __le16 rec_len; /* Directory entry length */ - __u8 name_len; /* Name length */ - __u8 file_type; - char name[EXT2_NAME_LEN]; /* File name */ -}; - -/* - * Ext2 directory file types. Only the low 3 bits are used. The - * other bits are reserved for now. - */ -enum { - EXT2_FT_UNKNOWN = 0, - EXT2_FT_REG_FILE = 1, - EXT2_FT_DIR = 2, - EXT2_FT_CHRDEV = 3, - EXT2_FT_BLKDEV = 4, - EXT2_FT_FIFO = 5, - EXT2_FT_SOCK = 6, - EXT2_FT_SYMLINK = 7, - EXT2_FT_MAX -}; - -/* - * EXT2_DIR_PAD defines the directory entries boundaries - * - * NOTE: It must be a multiple of 4 - */ -#define EXT2_DIR_PAD 4 -#define EXT2_DIR_ROUND (EXT2_DIR_PAD - 1) -#define EXT2_DIR_REC_LEN(name_len) (((name_len) + 8 + EXT2_DIR_ROUND) & \ - ~EXT2_DIR_ROUND) -#define EXT2_MAX_REC_LEN ((1<<16)-1) - #endif /* _LINUX_EXT2_FS_H */ diff --git a/include/linux/ext2_fs_sb.h b/include/linux/ext2_fs_sb.h deleted file mode 100644 index db4d9f586bb..00000000000 --- a/include/linux/ext2_fs_sb.h +++ /dev/null @@ -1,126 +0,0 @@ -/* - * linux/include/linux/ext2_fs_sb.h - * - * Copyright (C) 1992, 1993, 1994, 1995 - * Remy Card (card@masi.ibp.fr) - * Laboratoire MASI - Institut Blaise Pascal - * Universite Pierre et Marie Curie (Paris VI) - * - * from - * - * linux/include/linux/minix_fs_sb.h - * - * Copyright (C) 1991, 1992 Linus Torvalds - */ - -#ifndef _LINUX_EXT2_FS_SB -#define _LINUX_EXT2_FS_SB - -#include <linux/blockgroup_lock.h> -#include <linux/percpu_counter.h> -#include <linux/rbtree.h> - -/* XXX Here for now... not interested in restructing headers JUST now */ - -/* data type for block offset of block group */ -typedef int ext2_grpblk_t; - -/* data type for filesystem-wide blocks number */ -typedef unsigned long ext2_fsblk_t; - -#define E2FSBLK "%lu" - -struct ext2_reserve_window { - ext2_fsblk_t _rsv_start; /* First byte reserved */ - ext2_fsblk_t _rsv_end; /* Last byte reserved or 0 */ -}; - -struct ext2_reserve_window_node { - struct rb_node rsv_node; - __u32 rsv_goal_size; - __u32 rsv_alloc_hit; - struct ext2_reserve_window rsv_window; -}; - -struct ext2_block_alloc_info { - /* information about reservation window */ - struct ext2_reserve_window_node rsv_window_node; - /* - * was i_next_alloc_block in ext2_inode_info - * is the logical (file-relative) number of the - * most-recently-allocated block in this file. - * We use this for detecting linearly ascending allocation requests. - */ - __u32 last_alloc_logical_block; - /* - * Was i_next_alloc_goal in ext2_inode_info - * is the *physical* companion to i_next_alloc_block. - * it the the physical block number of the block which was most-recentl - * allocated to this file. This give us the goal (target) for the next - * allocation when we detect linearly ascending requests. - */ - ext2_fsblk_t last_alloc_physical_block; -}; - -#define rsv_start rsv_window._rsv_start -#define rsv_end rsv_window._rsv_end - -/* - * second extended-fs super-block data in memory - */ -struct ext2_sb_info { - unsigned long s_frag_size; /* Size of a fragment in bytes */ - unsigned long s_frags_per_block;/* Number of fragments per block */ - unsigned long s_inodes_per_block;/* Number of inodes per block */ - unsigned long s_frags_per_group;/* Number of fragments in a group */ - unsigned long s_blocks_per_group;/* Number of blocks in a group */ - unsigned long s_inodes_per_group;/* Number of inodes in a group */ - unsigned long s_itb_per_group; /* Number of inode table blocks per group */ - unsigned long s_gdb_count; /* Number of group descriptor blocks */ - unsigned long s_desc_per_block; /* Number of group descriptors per block */ - unsigned long s_groups_count; /* Number of groups in the fs */ - unsigned long s_overhead_last; /* Last calculated overhead */ - unsigned long s_blocks_last; /* Last seen block count */ - struct buffer_head * s_sbh; /* Buffer containing the super block */ - struct ext2_super_block * s_es; /* Pointer to the super block in the buffer */ - struct buffer_head ** s_group_desc; - unsigned long s_mount_opt; - unsigned long s_sb_block; - uid_t s_resuid; - gid_t s_resgid; - unsigned short s_mount_state; - unsigned short s_pad; - int s_addr_per_block_bits; - int s_desc_per_block_bits; - int s_inode_size; - int s_first_ino; - spinlock_t s_next_gen_lock; - u32 s_next_generation; - unsigned long s_dir_count; - u8 *s_debts; - struct percpu_counter s_freeblocks_counter; - struct percpu_counter s_freeinodes_counter; - struct percpu_counter s_dirs_counter; - struct blockgroup_lock *s_blockgroup_lock; - /* root of the per fs reservation window tree */ - spinlock_t s_rsv_window_lock; - struct rb_root s_rsv_window_root; - struct ext2_reserve_window_node s_rsv_window_head; - /* - * s_lock protects against concurrent modifications of s_mount_state, - * s_blocks_last, s_overhead_last and the content of superblock's - * buffer pointed to by sbi->s_es. - * - * Note: It is used in ext2_show_options() to provide a consistent view - * of the mount options. - */ - spinlock_t s_lock; -}; - -static inline spinlock_t * -sb_bgl_lock(struct ext2_sb_info *sbi, unsigned int block_group) -{ - return bgl_lock_ptr(sbi->s_blockgroup_lock, block_group); -} - -#endif /* _LINUX_EXT2_FS_SB */ diff --git a/include/linux/ext3_fs.h b/include/linux/ext3_fs.h deleted file mode 100644 index f5a84eef6ed..00000000000 --- a/include/linux/ext3_fs.h +++ /dev/null @@ -1,980 +0,0 @@ -/* - * linux/include/linux/ext3_fs.h - * - * Copyright (C) 1992, 1993, 1994, 1995 - * Remy Card (card@masi.ibp.fr) - * Laboratoire MASI - Institut Blaise Pascal - * Universite Pierre et Marie Curie (Paris VI) - * - * from - * - * linux/include/linux/minix_fs.h - * - * Copyright (C) 1991, 1992 Linus Torvalds - */ - -#ifndef _LINUX_EXT3_FS_H -#define _LINUX_EXT3_FS_H - -#include <linux/types.h> -#include <linux/magic.h> -#include <linux/bug.h> - -/* - * The second extended filesystem constants/structures - */ - -/* - * Define EXT3FS_DEBUG to produce debug messages - */ -#undef EXT3FS_DEBUG - -/* - * Define EXT3_RESERVATION to reserve data blocks for expanding files - */ -#define EXT3_DEFAULT_RESERVE_BLOCKS 8 -/*max window size: 1024(direct blocks) + 3([t,d]indirect blocks) */ -#define EXT3_MAX_RESERVE_BLOCKS 1027 -#define EXT3_RESERVE_WINDOW_NOT_ALLOCATED 0 - -/* - * Debug code - */ -#ifdef EXT3FS_DEBUG -#define ext3_debug(f, a...) \ - do { \ - printk (KERN_DEBUG "EXT3-fs DEBUG (%s, %d): %s:", \ - __FILE__, __LINE__, __func__); \ - printk (KERN_DEBUG f, ## a); \ - } while (0) -#else -#define ext3_debug(f, a...) do {} while (0) -#endif - -/* - * Special inodes numbers - */ -#define EXT3_BAD_INO 1 /* Bad blocks inode */ -#define EXT3_ROOT_INO 2 /* Root inode */ -#define EXT3_BOOT_LOADER_INO 5 /* Boot loader inode */ -#define EXT3_UNDEL_DIR_INO 6 /* Undelete directory inode */ -#define EXT3_RESIZE_INO 7 /* Reserved group descriptors inode */ -#define EXT3_JOURNAL_INO 8 /* Journal inode */ - -/* First non-reserved inode for old ext3 filesystems */ -#define EXT3_GOOD_OLD_FIRST_INO 11 - -/* - * Maximal count of links to a file - */ -#define EXT3_LINK_MAX 32000 - -/* - * Macro-instructions used to manage several block sizes - */ -#define EXT3_MIN_BLOCK_SIZE 1024 -#define EXT3_MAX_BLOCK_SIZE 65536 -#define EXT3_MIN_BLOCK_LOG_SIZE 10 -#ifdef __KERNEL__ -# define EXT3_BLOCK_SIZE(s) ((s)->s_blocksize) -#else -# define EXT3_BLOCK_SIZE(s) (EXT3_MIN_BLOCK_SIZE << (s)->s_log_block_size) -#endif -#define EXT3_ADDR_PER_BLOCK(s) (EXT3_BLOCK_SIZE(s) / sizeof (__u32)) -#ifdef __KERNEL__ -# define EXT3_BLOCK_SIZE_BITS(s) ((s)->s_blocksize_bits) -#else -# define EXT3_BLOCK_SIZE_BITS(s) ((s)->s_log_block_size + 10) -#endif -#ifdef __KERNEL__ -#define EXT3_ADDR_PER_BLOCK_BITS(s) (EXT3_SB(s)->s_addr_per_block_bits) -#define EXT3_INODE_SIZE(s) (EXT3_SB(s)->s_inode_size) -#define EXT3_FIRST_INO(s) (EXT3_SB(s)->s_first_ino) -#else -#define EXT3_INODE_SIZE(s) (((s)->s_rev_level == EXT3_GOOD_OLD_REV) ? \ - EXT3_GOOD_OLD_INODE_SIZE : \ - (s)->s_inode_size) -#define EXT3_FIRST_INO(s) (((s)->s_rev_level == EXT3_GOOD_OLD_REV) ? \ - EXT3_GOOD_OLD_FIRST_INO : \ - (s)->s_first_ino) -#endif - -/* - * Macro-instructions used to manage fragments - */ -#define EXT3_MIN_FRAG_SIZE 1024 -#define EXT3_MAX_FRAG_SIZE 4096 -#define EXT3_MIN_FRAG_LOG_SIZE 10 -#ifdef __KERNEL__ -# define EXT3_FRAG_SIZE(s) (EXT3_SB(s)->s_frag_size) -# define EXT3_FRAGS_PER_BLOCK(s) (EXT3_SB(s)->s_frags_per_block) -#else -# define EXT3_FRAG_SIZE(s) (EXT3_MIN_FRAG_SIZE << (s)->s_log_frag_size) -# define EXT3_FRAGS_PER_BLOCK(s) (EXT3_BLOCK_SIZE(s) / EXT3_FRAG_SIZE(s)) -#endif - -/* - * Structure of a blocks group descriptor - */ -struct ext3_group_desc -{ - __le32 bg_block_bitmap; /* Blocks bitmap block */ - __le32 bg_inode_bitmap; /* Inodes bitmap block */ - __le32 bg_inode_table; /* Inodes table block */ - __le16 bg_free_blocks_count; /* Free blocks count */ - __le16 bg_free_inodes_count; /* Free inodes count */ - __le16 bg_used_dirs_count; /* Directories count */ - __u16 bg_pad; - __le32 bg_reserved[3]; -}; - -/* - * Macro-instructions used to manage group descriptors - */ -#ifdef __KERNEL__ -# define EXT3_BLOCKS_PER_GROUP(s) (EXT3_SB(s)->s_blocks_per_group) -# define EXT3_DESC_PER_BLOCK(s) (EXT3_SB(s)->s_desc_per_block) -# define EXT3_INODES_PER_GROUP(s) (EXT3_SB(s)->s_inodes_per_group) -# define EXT3_DESC_PER_BLOCK_BITS(s) (EXT3_SB(s)->s_desc_per_block_bits) -#else -# define EXT3_BLOCKS_PER_GROUP(s) ((s)->s_blocks_per_group) -# define EXT3_DESC_PER_BLOCK(s) (EXT3_BLOCK_SIZE(s) / sizeof (struct ext3_group_desc)) -# define EXT3_INODES_PER_GROUP(s) ((s)->s_inodes_per_group) -#endif - -/* - * Constants relative to the data blocks - */ -#define EXT3_NDIR_BLOCKS 12 -#define EXT3_IND_BLOCK EXT3_NDIR_BLOCKS -#define EXT3_DIND_BLOCK (EXT3_IND_BLOCK + 1) -#define EXT3_TIND_BLOCK (EXT3_DIND_BLOCK + 1) -#define EXT3_N_BLOCKS (EXT3_TIND_BLOCK + 1) - -/* - * Inode flags - */ -#define EXT3_SECRM_FL 0x00000001 /* Secure deletion */ -#define EXT3_UNRM_FL 0x00000002 /* Undelete */ -#define EXT3_COMPR_FL 0x00000004 /* Compress file */ -#define EXT3_SYNC_FL 0x00000008 /* Synchronous updates */ -#define EXT3_IMMUTABLE_FL 0x00000010 /* Immutable file */ -#define EXT3_APPEND_FL 0x00000020 /* writes to file may only append */ -#define EXT3_NODUMP_FL 0x00000040 /* do not dump file */ -#define EXT3_NOATIME_FL 0x00000080 /* do not update atime */ -/* Reserved for compression usage... */ -#define EXT3_DIRTY_FL 0x00000100 -#define EXT3_COMPRBLK_FL 0x00000200 /* One or more compressed clusters */ -#define EXT3_NOCOMPR_FL 0x00000400 /* Don't compress */ -#define EXT3_ECOMPR_FL 0x00000800 /* Compression error */ -/* End compression flags --- maybe not all used */ -#define EXT3_INDEX_FL 0x00001000 /* hash-indexed directory */ -#define EXT3_IMAGIC_FL 0x00002000 /* AFS directory */ -#define EXT3_JOURNAL_DATA_FL 0x00004000 /* file data should be journaled */ -#define EXT3_NOTAIL_FL 0x00008000 /* file tail should not be merged */ -#define EXT3_DIRSYNC_FL 0x00010000 /* dirsync behaviour (directories only) */ -#define EXT3_TOPDIR_FL 0x00020000 /* Top of directory hierarchies*/ -#define EXT3_RESERVED_FL 0x80000000 /* reserved for ext3 lib */ - -#define EXT3_FL_USER_VISIBLE 0x0003DFFF /* User visible flags */ -#define EXT3_FL_USER_MODIFIABLE 0x000380FF /* User modifiable flags */ - -/* Flags that should be inherited by new inodes from their parent. */ -#define EXT3_FL_INHERITED (EXT3_SECRM_FL | EXT3_UNRM_FL | EXT3_COMPR_FL |\ - EXT3_SYNC_FL | EXT3_NODUMP_FL |\ - EXT3_NOATIME_FL | EXT3_COMPRBLK_FL |\ - EXT3_NOCOMPR_FL | EXT3_JOURNAL_DATA_FL |\ - EXT3_NOTAIL_FL | EXT3_DIRSYNC_FL) - -/* Flags that are appropriate for regular files (all but dir-specific ones). */ -#define EXT3_REG_FLMASK (~(EXT3_DIRSYNC_FL | EXT3_TOPDIR_FL)) - -/* Flags that are appropriate for non-directories/regular files. */ -#define EXT3_OTHER_FLMASK (EXT3_NODUMP_FL | EXT3_NOATIME_FL) - -/* Mask out flags that are inappropriate for the given type of inode. */ -static inline __u32 ext3_mask_flags(umode_t mode, __u32 flags) -{ - if (S_ISDIR(mode)) - return flags; - else if (S_ISREG(mode)) - return flags & EXT3_REG_FLMASK; - else - return flags & EXT3_OTHER_FLMASK; -} - -/* Used to pass group descriptor data when online resize is done */ -struct ext3_new_group_input { - __u32 group; /* Group number for this data */ - __u32 block_bitmap; /* Absolute block number of block bitmap */ - __u32 inode_bitmap; /* Absolute block number of inode bitmap */ - __u32 inode_table; /* Absolute block number of inode table start */ - __u32 blocks_count; /* Total number of blocks in this group */ - __u16 reserved_blocks; /* Number of reserved blocks in this group */ - __u16 unused; -}; - -/* The struct ext3_new_group_input in kernel space, with free_blocks_count */ -struct ext3_new_group_data { - __u32 group; - __u32 block_bitmap; - __u32 inode_bitmap; - __u32 inode_table; - __u32 blocks_count; - __u16 reserved_blocks; - __u16 unused; - __u32 free_blocks_count; -}; - - -/* - * ioctl commands - */ -#define EXT3_IOC_GETFLAGS FS_IOC_GETFLAGS -#define EXT3_IOC_SETFLAGS FS_IOC_SETFLAGS -#define EXT3_IOC_GETVERSION _IOR('f', 3, long) -#define EXT3_IOC_SETVERSION _IOW('f', 4, long) -#define EXT3_IOC_GROUP_EXTEND _IOW('f', 7, unsigned long) -#define EXT3_IOC_GROUP_ADD _IOW('f', 8,struct ext3_new_group_input) -#define EXT3_IOC_GETVERSION_OLD FS_IOC_GETVERSION -#define EXT3_IOC_SETVERSION_OLD FS_IOC_SETVERSION -#ifdef CONFIG_JBD_DEBUG -#define EXT3_IOC_WAIT_FOR_READONLY _IOR('f', 99, long) -#endif -#define EXT3_IOC_GETRSVSZ _IOR('f', 5, long) -#define EXT3_IOC_SETRSVSZ _IOW('f', 6, long) - -/* - * ioctl commands in 32 bit emulation - */ -#define EXT3_IOC32_GETFLAGS FS_IOC32_GETFLAGS -#define EXT3_IOC32_SETFLAGS FS_IOC32_SETFLAGS -#define EXT3_IOC32_GETVERSION _IOR('f', 3, int) -#define EXT3_IOC32_SETVERSION _IOW('f', 4, int) -#define EXT3_IOC32_GETRSVSZ _IOR('f', 5, int) -#define EXT3_IOC32_SETRSVSZ _IOW('f', 6, int) -#define EXT3_IOC32_GROUP_EXTEND _IOW('f', 7, unsigned int) -#ifdef CONFIG_JBD_DEBUG -#define EXT3_IOC32_WAIT_FOR_READONLY _IOR('f', 99, int) -#endif -#define EXT3_IOC32_GETVERSION_OLD FS_IOC32_GETVERSION -#define EXT3_IOC32_SETVERSION_OLD FS_IOC32_SETVERSION - - -/* - * Mount options - */ -struct ext3_mount_options { - unsigned long s_mount_opt; - uid_t s_resuid; - gid_t s_resgid; - unsigned long s_commit_interval; -#ifdef CONFIG_QUOTA - int s_jquota_fmt; - char *s_qf_names[MAXQUOTAS]; -#endif -}; - -/* - * Structure of an inode on the disk - */ -struct ext3_inode { - __le16 i_mode; /* File mode */ - __le16 i_uid; /* Low 16 bits of Owner Uid */ - __le32 i_size; /* Size in bytes */ - __le32 i_atime; /* Access time */ - __le32 i_ctime; /* Creation time */ - __le32 i_mtime; /* Modification time */ - __le32 i_dtime; /* Deletion Time */ - __le16 i_gid; /* Low 16 bits of Group Id */ - __le16 i_links_count; /* Links count */ - __le32 i_blocks; /* Blocks count */ - __le32 i_flags; /* File flags */ - union { - struct { - __u32 l_i_reserved1; - } linux1; - struct { - __u32 h_i_translator; - } hurd1; - struct { - __u32 m_i_reserved1; - } masix1; - } osd1; /* OS dependent 1 */ - __le32 i_block[EXT3_N_BLOCKS];/* Pointers to blocks */ - __le32 i_generation; /* File version (for NFS) */ - __le32 i_file_acl; /* File ACL */ - __le32 i_dir_acl; /* Directory ACL */ - __le32 i_faddr; /* Fragment address */ - union { - struct { - __u8 l_i_frag; /* Fragment number */ - __u8 l_i_fsize; /* Fragment size */ - __u16 i_pad1; - __le16 l_i_uid_high; /* these 2 fields */ - __le16 l_i_gid_high; /* were reserved2[0] */ - __u32 l_i_reserved2; - } linux2; - struct { - __u8 h_i_frag; /* Fragment number */ - __u8 h_i_fsize; /* Fragment size */ - __u16 h_i_mode_high; - __u16 h_i_uid_high; - __u16 h_i_gid_high; - __u32 h_i_author; - } hurd2; - struct { - __u8 m_i_frag; /* Fragment number */ - __u8 m_i_fsize; /* Fragment size */ - __u16 m_pad1; - __u32 m_i_reserved2[2]; - } masix2; - } osd2; /* OS dependent 2 */ - __le16 i_extra_isize; - __le16 i_pad1; -}; - -#define i_size_high i_dir_acl - -#if defined(__KERNEL__) || defined(__linux__) -#define i_reserved1 osd1.linux1.l_i_reserved1 -#define i_frag osd2.linux2.l_i_frag -#define i_fsize osd2.linux2.l_i_fsize -#define i_uid_low i_uid -#define i_gid_low i_gid -#define i_uid_high osd2.linux2.l_i_uid_high -#define i_gid_high osd2.linux2.l_i_gid_high -#define i_reserved2 osd2.linux2.l_i_reserved2 - -#elif defined(__GNU__) - -#define i_translator osd1.hurd1.h_i_translator -#define i_frag osd2.hurd2.h_i_frag; -#define i_fsize osd2.hurd2.h_i_fsize; -#define i_uid_high osd2.hurd2.h_i_uid_high -#define i_gid_high osd2.hurd2.h_i_gid_high -#define i_author osd2.hurd2.h_i_author - -#elif defined(__masix__) - -#define i_reserved1 osd1.masix1.m_i_reserved1 -#define i_frag osd2.masix2.m_i_frag -#define i_fsize osd2.masix2.m_i_fsize -#define i_reserved2 osd2.masix2.m_i_reserved2 - -#endif /* defined(__KERNEL__) || defined(__linux__) */ - -/* - * File system states - */ -#define EXT3_VALID_FS 0x0001 /* Unmounted cleanly */ -#define EXT3_ERROR_FS 0x0002 /* Errors detected */ -#define EXT3_ORPHAN_FS 0x0004 /* Orphans being recovered */ - -/* - * Misc. filesystem flags - */ -#define EXT2_FLAGS_SIGNED_HASH 0x0001 /* Signed dirhash in use */ -#define EXT2_FLAGS_UNSIGNED_HASH 0x0002 /* Unsigned dirhash in use */ -#define EXT2_FLAGS_TEST_FILESYS 0x0004 /* to test development code */ - -/* - * Mount flags - */ -#define EXT3_MOUNT_CHECK 0x00001 /* Do mount-time checks */ -/* EXT3_MOUNT_OLDALLOC was there */ -#define EXT3_MOUNT_GRPID 0x00004 /* Create files with directory's group */ -#define EXT3_MOUNT_DEBUG 0x00008 /* Some debugging messages */ -#define EXT3_MOUNT_ERRORS_CONT 0x00010 /* Continue on errors */ -#define EXT3_MOUNT_ERRORS_RO 0x00020 /* Remount fs ro on errors */ -#define EXT3_MOUNT_ERRORS_PANIC 0x00040 /* Panic on errors */ -#define EXT3_MOUNT_MINIX_DF 0x00080 /* Mimics the Minix statfs */ -#define EXT3_MOUNT_NOLOAD 0x00100 /* Don't use existing journal*/ -#define EXT3_MOUNT_ABORT 0x00200 /* Fatal error detected */ -#define EXT3_MOUNT_DATA_FLAGS 0x00C00 /* Mode for data writes: */ -#define EXT3_MOUNT_JOURNAL_DATA 0x00400 /* Write data to journal */ -#define EXT3_MOUNT_ORDERED_DATA 0x00800 /* Flush data before commit */ -#define EXT3_MOUNT_WRITEBACK_DATA 0x00C00 /* No data ordering */ -#define EXT3_MOUNT_UPDATE_JOURNAL 0x01000 /* Update the journal format */ -#define EXT3_MOUNT_NO_UID32 0x02000 /* Disable 32-bit UIDs */ -#define EXT3_MOUNT_XATTR_USER 0x04000 /* Extended user attributes */ -#define EXT3_MOUNT_POSIX_ACL 0x08000 /* POSIX Access Control Lists */ -#define EXT3_MOUNT_RESERVATION 0x10000 /* Preallocation */ -#define EXT3_MOUNT_BARRIER 0x20000 /* Use block barriers */ -#define EXT3_MOUNT_QUOTA 0x80000 /* Some quota option set */ -#define EXT3_MOUNT_USRQUOTA 0x100000 /* "old" user quota */ -#define EXT3_MOUNT_GRPQUOTA 0x200000 /* "old" group quota */ -#define EXT3_MOUNT_DATA_ERR_ABORT 0x400000 /* Abort on file data write - * error in ordered mode */ - -/* Compatibility, for having both ext2_fs.h and ext3_fs.h included at once */ -#ifndef _LINUX_EXT2_FS_H -#define clear_opt(o, opt) o &= ~EXT3_MOUNT_##opt -#define set_opt(o, opt) o |= EXT3_MOUNT_##opt -#define test_opt(sb, opt) (EXT3_SB(sb)->s_mount_opt & \ - EXT3_MOUNT_##opt) -#else -#define EXT2_MOUNT_NOLOAD EXT3_MOUNT_NOLOAD -#define EXT2_MOUNT_ABORT EXT3_MOUNT_ABORT -#define EXT2_MOUNT_DATA_FLAGS EXT3_MOUNT_DATA_FLAGS -#endif - -#define ext3_set_bit __set_bit_le -#define ext3_set_bit_atomic ext2_set_bit_atomic -#define ext3_clear_bit __clear_bit_le -#define ext3_clear_bit_atomic ext2_clear_bit_atomic -#define ext3_test_bit test_bit_le -#define ext3_find_next_zero_bit find_next_zero_bit_le - -/* - * Maximal mount counts between two filesystem checks - */ -#define EXT3_DFL_MAX_MNT_COUNT 20 /* Allow 20 mounts */ -#define EXT3_DFL_CHECKINTERVAL 0 /* Don't use interval check */ - -/* - * Behaviour when detecting errors - */ -#define EXT3_ERRORS_CONTINUE 1 /* Continue execution */ -#define EXT3_ERRORS_RO 2 /* Remount fs read-only */ -#define EXT3_ERRORS_PANIC 3 /* Panic */ -#define EXT3_ERRORS_DEFAULT EXT3_ERRORS_CONTINUE - -/* - * Structure of the super block - */ -struct ext3_super_block { -/*00*/ __le32 s_inodes_count; /* Inodes count */ - __le32 s_blocks_count; /* Blocks count */ - __le32 s_r_blocks_count; /* Reserved blocks count */ - __le32 s_free_blocks_count; /* Free blocks count */ -/*10*/ __le32 s_free_inodes_count; /* Free inodes count */ - __le32 s_first_data_block; /* First Data Block */ - __le32 s_log_block_size; /* Block size */ - __le32 s_log_frag_size; /* Fragment size */ -/*20*/ __le32 s_blocks_per_group; /* # Blocks per group */ - __le32 s_frags_per_group; /* # Fragments per group */ - __le32 s_inodes_per_group; /* # Inodes per group */ - __le32 s_mtime; /* Mount time */ -/*30*/ __le32 s_wtime; /* Write time */ - __le16 s_mnt_count; /* Mount count */ - __le16 s_max_mnt_count; /* Maximal mount count */ - __le16 s_magic; /* Magic signature */ - __le16 s_state; /* File system state */ - __le16 s_errors; /* Behaviour when detecting errors */ - __le16 s_minor_rev_level; /* minor revision level */ -/*40*/ __le32 s_lastcheck; /* time of last check */ - __le32 s_checkinterval; /* max. time between checks */ - __le32 s_creator_os; /* OS */ - __le32 s_rev_level; /* Revision level */ -/*50*/ __le16 s_def_resuid; /* Default uid for reserved blocks */ - __le16 s_def_resgid; /* Default gid for reserved blocks */ - /* - * These fields are for EXT3_DYNAMIC_REV superblocks only. - * - * Note: the difference between the compatible feature set and - * the incompatible feature set is that if there is a bit set - * in the incompatible feature set that the kernel doesn't - * know about, it should refuse to mount the filesystem. - * - * e2fsck's requirements are more strict; if it doesn't know - * about a feature in either the compatible or incompatible - * feature set, it must abort and not try to meddle with - * things it doesn't understand... - */ - __le32 s_first_ino; /* First non-reserved inode */ - __le16 s_inode_size; /* size of inode structure */ - __le16 s_block_group_nr; /* block group # of this superblock */ - __le32 s_feature_compat; /* compatible feature set */ -/*60*/ __le32 s_feature_incompat; /* incompatible feature set */ - __le32 s_feature_ro_compat; /* readonly-compatible feature set */ -/*68*/ __u8 s_uuid[16]; /* 128-bit uuid for volume */ -/*78*/ char s_volume_name[16]; /* volume name */ -/*88*/ char s_last_mounted[64]; /* directory where last mounted */ -/*C8*/ __le32 s_algorithm_usage_bitmap; /* For compression */ - /* - * Performance hints. Directory preallocation should only - * happen if the EXT3_FEATURE_COMPAT_DIR_PREALLOC flag is on. - */ - __u8 s_prealloc_blocks; /* Nr of blocks to try to preallocate*/ - __u8 s_prealloc_dir_blocks; /* Nr to preallocate for dirs */ - __le16 s_reserved_gdt_blocks; /* Per group desc for online growth */ - /* - * Journaling support valid if EXT3_FEATURE_COMPAT_HAS_JOURNAL set. - */ -/*D0*/ __u8 s_journal_uuid[16]; /* uuid of journal superblock */ -/*E0*/ __le32 s_journal_inum; /* inode number of journal file */ - __le32 s_journal_dev; /* device number of journal file */ - __le32 s_last_orphan; /* start of list of inodes to delete */ - __le32 s_hash_seed[4]; /* HTREE hash seed */ - __u8 s_def_hash_version; /* Default hash version to use */ - __u8 s_reserved_char_pad; - __u16 s_reserved_word_pad; - __le32 s_default_mount_opts; - __le32 s_first_meta_bg; /* First metablock block group */ - __le32 s_mkfs_time; /* When the filesystem was created */ - __le32 s_jnl_blocks[17]; /* Backup of the journal inode */ - /* 64bit support valid if EXT4_FEATURE_COMPAT_64BIT */ -/*150*/ __le32 s_blocks_count_hi; /* Blocks count */ - __le32 s_r_blocks_count_hi; /* Reserved blocks count */ - __le32 s_free_blocks_count_hi; /* Free blocks count */ - __le16 s_min_extra_isize; /* All inodes have at least # bytes */ - __le16 s_want_extra_isize; /* New inodes should reserve # bytes */ - __le32 s_flags; /* Miscellaneous flags */ - __le16 s_raid_stride; /* RAID stride */ - __le16 s_mmp_interval; /* # seconds to wait in MMP checking */ - __le64 s_mmp_block; /* Block for multi-mount protection */ - __le32 s_raid_stripe_width; /* blocks on all data disks (N*stride)*/ - __u8 s_log_groups_per_flex; /* FLEX_BG group size */ - __u8 s_reserved_char_pad2; - __le16 s_reserved_pad; - __u32 s_reserved[162]; /* Padding to the end of the block */ -}; - -#ifdef __KERNEL__ -#include <linux/ext3_fs_i.h> -#include <linux/ext3_fs_sb.h> -static inline struct ext3_sb_info * EXT3_SB(struct super_block *sb) -{ - return sb->s_fs_info; -} -static inline struct ext3_inode_info *EXT3_I(struct inode *inode) -{ - return container_of(inode, struct ext3_inode_info, vfs_inode); -} - -static inline int ext3_valid_inum(struct super_block *sb, unsigned long ino) -{ - return ino == EXT3_ROOT_INO || - ino == EXT3_JOURNAL_INO || - ino == EXT3_RESIZE_INO || - (ino >= EXT3_FIRST_INO(sb) && - ino <= le32_to_cpu(EXT3_SB(sb)->s_es->s_inodes_count)); -} - -/* - * Inode dynamic state flags - */ -enum { - EXT3_STATE_JDATA, /* journaled data exists */ - EXT3_STATE_NEW, /* inode is newly created */ - EXT3_STATE_XATTR, /* has in-inode xattrs */ - EXT3_STATE_FLUSH_ON_CLOSE, /* flush dirty pages on close */ -}; - -static inline int ext3_test_inode_state(struct inode *inode, int bit) -{ - return test_bit(bit, &EXT3_I(inode)->i_state_flags); -} - -static inline void ext3_set_inode_state(struct inode *inode, int bit) -{ - set_bit(bit, &EXT3_I(inode)->i_state_flags); -} - -static inline void ext3_clear_inode_state(struct inode *inode, int bit) -{ - clear_bit(bit, &EXT3_I(inode)->i_state_flags); -} -#else -/* Assume that user mode programs are passing in an ext3fs superblock, not - * a kernel struct super_block. This will allow us to call the feature-test - * macros from user land. */ -#define EXT3_SB(sb) (sb) -#endif - -#define NEXT_ORPHAN(inode) EXT3_I(inode)->i_dtime - -/* - * Codes for operating systems - */ -#define EXT3_OS_LINUX 0 -#define EXT3_OS_HURD 1 -#define EXT3_OS_MASIX 2 -#define EXT3_OS_FREEBSD 3 -#define EXT3_OS_LITES 4 - -/* - * Revision levels - */ -#define EXT3_GOOD_OLD_REV 0 /* The good old (original) format */ -#define EXT3_DYNAMIC_REV 1 /* V2 format w/ dynamic inode sizes */ - -#define EXT3_CURRENT_REV EXT3_GOOD_OLD_REV -#define EXT3_MAX_SUPP_REV EXT3_DYNAMIC_REV - -#define EXT3_GOOD_OLD_INODE_SIZE 128 - -/* - * Feature set definitions - */ - -#define EXT3_HAS_COMPAT_FEATURE(sb,mask) \ - ( EXT3_SB(sb)->s_es->s_feature_compat & cpu_to_le32(mask) ) -#define EXT3_HAS_RO_COMPAT_FEATURE(sb,mask) \ - ( EXT3_SB(sb)->s_es->s_feature_ro_compat & cpu_to_le32(mask) ) -#define EXT3_HAS_INCOMPAT_FEATURE(sb,mask) \ - ( EXT3_SB(sb)->s_es->s_feature_incompat & cpu_to_le32(mask) ) -#define EXT3_SET_COMPAT_FEATURE(sb,mask) \ - EXT3_SB(sb)->s_es->s_feature_compat |= cpu_to_le32(mask) -#define EXT3_SET_RO_COMPAT_FEATURE(sb,mask) \ - EXT3_SB(sb)->s_es->s_feature_ro_compat |= cpu_to_le32(mask) -#define EXT3_SET_INCOMPAT_FEATURE(sb,mask) \ - EXT3_SB(sb)->s_es->s_feature_incompat |= cpu_to_le32(mask) -#define EXT3_CLEAR_COMPAT_FEATURE(sb,mask) \ - EXT3_SB(sb)->s_es->s_feature_compat &= ~cpu_to_le32(mask) -#define EXT3_CLEAR_RO_COMPAT_FEATURE(sb,mask) \ - EXT3_SB(sb)->s_es->s_feature_ro_compat &= ~cpu_to_le32(mask) -#define EXT3_CLEAR_INCOMPAT_FEATURE(sb,mask) \ - EXT3_SB(sb)->s_es->s_feature_incompat &= ~cpu_to_le32(mask) - -#define EXT3_FEATURE_COMPAT_DIR_PREALLOC 0x0001 -#define EXT3_FEATURE_COMPAT_IMAGIC_INODES 0x0002 -#define EXT3_FEATURE_COMPAT_HAS_JOURNAL 0x0004 -#define EXT3_FEATURE_COMPAT_EXT_ATTR 0x0008 -#define EXT3_FEATURE_COMPAT_RESIZE_INODE 0x0010 -#define EXT3_FEATURE_COMPAT_DIR_INDEX 0x0020 - -#define EXT3_FEATURE_RO_COMPAT_SPARSE_SUPER 0x0001 -#define EXT3_FEATURE_RO_COMPAT_LARGE_FILE 0x0002 -#define EXT3_FEATURE_RO_COMPAT_BTREE_DIR 0x0004 - -#define EXT3_FEATURE_INCOMPAT_COMPRESSION 0x0001 -#define EXT3_FEATURE_INCOMPAT_FILETYPE 0x0002 -#define EXT3_FEATURE_INCOMPAT_RECOVER 0x0004 /* Needs recovery */ -#define EXT3_FEATURE_INCOMPAT_JOURNAL_DEV 0x0008 /* Journal device */ -#define EXT3_FEATURE_INCOMPAT_META_BG 0x0010 - -#define EXT3_FEATURE_COMPAT_SUPP EXT2_FEATURE_COMPAT_EXT_ATTR -#define EXT3_FEATURE_INCOMPAT_SUPP (EXT3_FEATURE_INCOMPAT_FILETYPE| \ - EXT3_FEATURE_INCOMPAT_RECOVER| \ - EXT3_FEATURE_INCOMPAT_META_BG) -#define EXT3_FEATURE_RO_COMPAT_SUPP (EXT3_FEATURE_RO_COMPAT_SPARSE_SUPER| \ - EXT3_FEATURE_RO_COMPAT_LARGE_FILE| \ - EXT3_FEATURE_RO_COMPAT_BTREE_DIR) - -/* - * Default values for user and/or group using reserved blocks - */ -#define EXT3_DEF_RESUID 0 -#define EXT3_DEF_RESGID 0 - -/* - * Default mount options - */ -#define EXT3_DEFM_DEBUG 0x0001 -#define EXT3_DEFM_BSDGROUPS 0x0002 -#define EXT3_DEFM_XATTR_USER 0x0004 -#define EXT3_DEFM_ACL 0x0008 -#define EXT3_DEFM_UID16 0x0010 -#define EXT3_DEFM_JMODE 0x0060 -#define EXT3_DEFM_JMODE_DATA 0x0020 -#define EXT3_DEFM_JMODE_ORDERED 0x0040 -#define EXT3_DEFM_JMODE_WBACK 0x0060 - -/* - * Structure of a directory entry - */ -#define EXT3_NAME_LEN 255 - -struct ext3_dir_entry { - __le32 inode; /* Inode number */ - __le16 rec_len; /* Directory entry length */ - __le16 name_len; /* Name length */ - char name[EXT3_NAME_LEN]; /* File name */ -}; - -/* - * The new version of the directory entry. Since EXT3 structures are - * stored in intel byte order, and the name_len field could never be - * bigger than 255 chars, it's safe to reclaim the extra byte for the - * file_type field. - */ -struct ext3_dir_entry_2 { - __le32 inode; /* Inode number */ - __le16 rec_len; /* Directory entry length */ - __u8 name_len; /* Name length */ - __u8 file_type; - char name[EXT3_NAME_LEN]; /* File name */ -}; - -/* - * Ext3 directory file types. Only the low 3 bits are used. The - * other bits are reserved for now. - */ -#define EXT3_FT_UNKNOWN 0 -#define EXT3_FT_REG_FILE 1 -#define EXT3_FT_DIR 2 -#define EXT3_FT_CHRDEV 3 -#define EXT3_FT_BLKDEV 4 -#define EXT3_FT_FIFO 5 -#define EXT3_FT_SOCK 6 -#define EXT3_FT_SYMLINK 7 - -#define EXT3_FT_MAX 8 - -/* - * EXT3_DIR_PAD defines the directory entries boundaries - * - * NOTE: It must be a multiple of 4 - */ -#define EXT3_DIR_PAD 4 -#define EXT3_DIR_ROUND (EXT3_DIR_PAD - 1) -#define EXT3_DIR_REC_LEN(name_len) (((name_len) + 8 + EXT3_DIR_ROUND) & \ - ~EXT3_DIR_ROUND) -#define EXT3_MAX_REC_LEN ((1<<16)-1) - -/* - * Tests against MAX_REC_LEN etc were put in place for 64k block - * sizes; if that is not possible on this arch, we can skip - * those tests and speed things up. - */ -static inline unsigned ext3_rec_len_from_disk(__le16 dlen) -{ - unsigned len = le16_to_cpu(dlen); - -#if (PAGE_CACHE_SIZE >= 65536) - if (len == EXT3_MAX_REC_LEN) - return 1 << 16; -#endif - return len; -} - -static inline __le16 ext3_rec_len_to_disk(unsigned len) -{ -#if (PAGE_CACHE_SIZE >= 65536) - if (len == (1 << 16)) - return cpu_to_le16(EXT3_MAX_REC_LEN); - else if (len > (1 << 16)) - BUG(); -#endif - return cpu_to_le16(len); -} - -/* - * Hash Tree Directory indexing - * (c) Daniel Phillips, 2001 - */ - -#define is_dx(dir) (EXT3_HAS_COMPAT_FEATURE(dir->i_sb, \ - EXT3_FEATURE_COMPAT_DIR_INDEX) && \ - (EXT3_I(dir)->i_flags & EXT3_INDEX_FL)) -#define EXT3_DIR_LINK_MAX(dir) (!is_dx(dir) && (dir)->i_nlink >= EXT3_LINK_MAX) -#define EXT3_DIR_LINK_EMPTY(dir) ((dir)->i_nlink == 2 || (dir)->i_nlink == 1) - -/* Legal values for the dx_root hash_version field: */ - -#define DX_HASH_LEGACY 0 -#define DX_HASH_HALF_MD4 1 -#define DX_HASH_TEA 2 -#define DX_HASH_LEGACY_UNSIGNED 3 -#define DX_HASH_HALF_MD4_UNSIGNED 4 -#define DX_HASH_TEA_UNSIGNED 5 - -#ifdef __KERNEL__ - -/* hash info structure used by the directory hash */ -struct dx_hash_info -{ - u32 hash; - u32 minor_hash; - int hash_version; - u32 *seed; -}; - -#define EXT3_HTREE_EOF 0x7fffffff - -/* - * Control parameters used by ext3_htree_next_block - */ -#define HASH_NB_ALWAYS 1 - - -/* - * Describe an inode's exact location on disk and in memory - */ -struct ext3_iloc -{ - struct buffer_head *bh; - unsigned long offset; - unsigned long block_group; -}; - -static inline struct ext3_inode *ext3_raw_inode(struct ext3_iloc *iloc) -{ - return (struct ext3_inode *) (iloc->bh->b_data + iloc->offset); -} - -/* - * This structure is stuffed into the struct file's private_data field - * for directories. It is where we put information so that we can do - * readdir operations in hash tree order. - */ -struct dir_private_info { - struct rb_root root; - struct rb_node *curr_node; - struct fname *extra_fname; - loff_t last_pos; - __u32 curr_hash; - __u32 curr_minor_hash; - __u32 next_hash; -}; - -/* calculate the first block number of the group */ -static inline ext3_fsblk_t -ext3_group_first_block_no(struct super_block *sb, unsigned long group_no) -{ - return group_no * (ext3_fsblk_t)EXT3_BLOCKS_PER_GROUP(sb) + - le32_to_cpu(EXT3_SB(sb)->s_es->s_first_data_block); -} - -/* - * Special error return code only used by dx_probe() and its callers. - */ -#define ERR_BAD_DX_DIR -75000 - -/* - * Function prototypes - */ - -/* - * Ok, these declarations are also in <linux/kernel.h> but none of the - * ext3 source programs needs to include it so they are duplicated here. - */ -# define NORET_TYPE /**/ -# define ATTRIB_NORET __attribute__((noreturn)) -# define NORET_AND noreturn, - -/* balloc.c */ -extern int ext3_bg_has_super(struct super_block *sb, int group); -extern unsigned long ext3_bg_num_gdb(struct super_block *sb, int group); -extern ext3_fsblk_t ext3_new_block (handle_t *handle, struct inode *inode, - ext3_fsblk_t goal, int *errp); -extern ext3_fsblk_t ext3_new_blocks (handle_t *handle, struct inode *inode, - ext3_fsblk_t goal, unsigned long *count, int *errp); -extern void ext3_free_blocks (handle_t *handle, struct inode *inode, - ext3_fsblk_t block, unsigned long count); -extern void ext3_free_blocks_sb (handle_t *handle, struct super_block *sb, - ext3_fsblk_t block, unsigned long count, - unsigned long *pdquot_freed_blocks); -extern ext3_fsblk_t ext3_count_free_blocks (struct super_block *); -extern void ext3_check_blocks_bitmap (struct super_block *); -extern struct ext3_group_desc * ext3_get_group_desc(struct super_block * sb, - unsigned int block_group, - struct buffer_head ** bh); -extern int ext3_should_retry_alloc(struct super_block *sb, int *retries); -extern void ext3_init_block_alloc_info(struct inode *); -extern void ext3_rsv_window_add(struct super_block *sb, struct ext3_reserve_window_node *rsv); -extern int ext3_trim_fs(struct super_block *sb, struct fstrim_range *range); - -/* dir.c */ -extern int ext3_check_dir_entry(const char *, struct inode *, - struct ext3_dir_entry_2 *, - struct buffer_head *, unsigned long); -extern int ext3_htree_store_dirent(struct file *dir_file, __u32 hash, - __u32 minor_hash, - struct ext3_dir_entry_2 *dirent); -extern void ext3_htree_free_dir_info(struct dir_private_info *p); - -/* fsync.c */ -extern int ext3_sync_file(struct file *, loff_t, loff_t, int); - -/* hash.c */ -extern int ext3fs_dirhash(const char *name, int len, struct - dx_hash_info *hinfo); - -/* ialloc.c */ -extern struct inode * ext3_new_inode (handle_t *, struct inode *, - const struct qstr *, umode_t); -extern void ext3_free_inode (handle_t *, struct inode *); -extern struct inode * ext3_orphan_get (struct super_block *, unsigned long); -extern unsigned long ext3_count_free_inodes (struct super_block *); -extern unsigned long ext3_count_dirs (struct super_block *); -extern void ext3_check_inodes_bitmap (struct super_block *); -extern unsigned long ext3_count_free (struct buffer_head *, unsigned); - - -/* inode.c */ -int ext3_forget(handle_t *handle, int is_metadata, struct inode *inode, - struct buffer_head *bh, ext3_fsblk_t blocknr); -struct buffer_head * ext3_getblk (handle_t *, struct inode *, long, int, int *); -struct buffer_head * ext3_bread (handle_t *, struct inode *, int, int, int *); -int ext3_get_blocks_handle(handle_t *handle, struct inode *inode, - sector_t iblock, unsigned long maxblocks, struct buffer_head *bh_result, - int create); - -extern struct inode *ext3_iget(struct super_block *, unsigned long); -extern int ext3_write_inode (struct inode *, struct writeback_control *); -extern int ext3_setattr (struct dentry *, struct iattr *); -extern void ext3_evict_inode (struct inode *); -extern int ext3_sync_inode (handle_t *, struct inode *); -extern void ext3_discard_reservation (struct inode *); -extern void ext3_dirty_inode(struct inode *, int); -extern int ext3_change_inode_journal_flag(struct inode *, int); -extern int ext3_get_inode_loc(struct inode *, struct ext3_iloc *); -extern int ext3_can_truncate(struct inode *inode); -extern void ext3_truncate(struct inode *inode); -extern void ext3_set_inode_flags(struct inode *); -extern void ext3_get_inode_flags(struct ext3_inode_info *); -extern void ext3_set_aops(struct inode *inode); -extern int ext3_fiemap(struct inode *inode, struct fiemap_extent_info *fieinfo, - u64 start, u64 len); - -/* ioctl.c */ -extern long ext3_ioctl(struct file *, unsigned int, unsigned long); -extern long ext3_compat_ioctl(struct file *, unsigned int, unsigned long); - -/* namei.c */ -extern int ext3_orphan_add(handle_t *, struct inode *); -extern int ext3_orphan_del(handle_t *, struct inode *); -extern int ext3_htree_fill_tree(struct file *dir_file, __u32 start_hash, - __u32 start_minor_hash, __u32 *next_hash); - -/* resize.c */ -extern int ext3_group_add(struct super_block *sb, - struct ext3_new_group_data *input); -extern int ext3_group_extend(struct super_block *sb, - struct ext3_super_block *es, - ext3_fsblk_t n_blocks_count); - -/* super.c */ -extern __printf(3, 4) -void ext3_error(struct super_block *, const char *, const char *, ...); -extern void __ext3_std_error (struct super_block *, const char *, int); -extern __printf(3, 4) -void ext3_abort(struct super_block *, const char *, const char *, ...); -extern __printf(3, 4) -void ext3_warning(struct super_block *, const char *, const char *, ...); -extern __printf(3, 4) -void ext3_msg(struct super_block *, const char *, const char *, ...); -extern void ext3_update_dynamic_rev (struct super_block *sb); - -#define ext3_std_error(sb, errno) \ -do { \ - if ((errno)) \ - __ext3_std_error((sb), __func__, (errno)); \ -} while (0) - -/* - * Inodes and files operations - */ - -/* dir.c */ -extern const struct file_operations ext3_dir_operations; - -/* file.c */ -extern const struct inode_operations ext3_file_inode_operations; -extern const struct file_operations ext3_file_operations; - -/* namei.c */ -extern const struct inode_operations ext3_dir_inode_operations; -extern const struct inode_operations ext3_special_inode_operations; - -/* symlink.c */ -extern const struct inode_operations ext3_symlink_inode_operations; -extern const struct inode_operations ext3_fast_symlink_inode_operations; - - -#endif /* __KERNEL__ */ - -#endif /* _LINUX_EXT3_FS_H */ diff --git a/include/linux/ext3_fs_i.h b/include/linux/ext3_fs_i.h deleted file mode 100644 index f42c098aed8..00000000000 --- a/include/linux/ext3_fs_i.h +++ /dev/null @@ -1,151 +0,0 @@ -/* - * linux/include/linux/ext3_fs_i.h - * - * Copyright (C) 1992, 1993, 1994, 1995 - * Remy Card (card@masi.ibp.fr) - * Laboratoire MASI - Institut Blaise Pascal - * Universite Pierre et Marie Curie (Paris VI) - * - * from - * - * linux/include/linux/minix_fs_i.h - * - * Copyright (C) 1991, 1992 Linus Torvalds - */ - -#ifndef _LINUX_EXT3_FS_I -#define _LINUX_EXT3_FS_I - -#include <linux/rwsem.h> -#include <linux/rbtree.h> -#include <linux/seqlock.h> -#include <linux/mutex.h> - -/* data type for block offset of block group */ -typedef int ext3_grpblk_t; - -/* data type for filesystem-wide blocks number */ -typedef unsigned long ext3_fsblk_t; - -#define E3FSBLK "%lu" - -struct ext3_reserve_window { - ext3_fsblk_t _rsv_start; /* First byte reserved */ - ext3_fsblk_t _rsv_end; /* Last byte reserved or 0 */ -}; - -struct ext3_reserve_window_node { - struct rb_node rsv_node; - __u32 rsv_goal_size; - __u32 rsv_alloc_hit; - struct ext3_reserve_window rsv_window; -}; - -struct ext3_block_alloc_info { - /* information about reservation window */ - struct ext3_reserve_window_node rsv_window_node; - /* - * was i_next_alloc_block in ext3_inode_info - * is the logical (file-relative) number of the - * most-recently-allocated block in this file. - * We use this for detecting linearly ascending allocation requests. - */ - __u32 last_alloc_logical_block; - /* - * Was i_next_alloc_goal in ext3_inode_info - * is the *physical* companion to i_next_alloc_block. - * it the physical block number of the block which was most-recentl - * allocated to this file. This give us the goal (target) for the next - * allocation when we detect linearly ascending requests. - */ - ext3_fsblk_t last_alloc_physical_block; -}; - -#define rsv_start rsv_window._rsv_start -#define rsv_end rsv_window._rsv_end - -/* - * third extended file system inode data in memory - */ -struct ext3_inode_info { - __le32 i_data[15]; /* unconverted */ - __u32 i_flags; -#ifdef EXT3_FRAGMENTS - __u32 i_faddr; - __u8 i_frag_no; - __u8 i_frag_size; -#endif - ext3_fsblk_t i_file_acl; - __u32 i_dir_acl; - __u32 i_dtime; - - /* - * i_block_group is the number of the block group which contains - * this file's inode. Constant across the lifetime of the inode, - * it is ued for making block allocation decisions - we try to - * place a file's data blocks near its inode block, and new inodes - * near to their parent directory's inode. - */ - __u32 i_block_group; - unsigned long i_state_flags; /* Dynamic state flags for ext3 */ - - /* block reservation info */ - struct ext3_block_alloc_info *i_block_alloc_info; - - __u32 i_dir_start_lookup; -#ifdef CONFIG_EXT3_FS_XATTR - /* - * Extended attributes can be read independently of the main file - * data. Taking i_mutex even when reading would cause contention - * between readers of EAs and writers of regular file data, so - * instead we synchronize on xattr_sem when reading or changing - * EAs. - */ - struct rw_semaphore xattr_sem; -#endif - - struct list_head i_orphan; /* unlinked but open inodes */ - - /* - * i_disksize keeps track of what the inode size is ON DISK, not - * in memory. During truncate, i_size is set to the new size by - * the VFS prior to calling ext3_truncate(), but the filesystem won't - * set i_disksize to 0 until the truncate is actually under way. - * - * The intent is that i_disksize always represents the blocks which - * are used by this file. This allows recovery to restart truncate - * on orphans if we crash during truncate. We actually write i_disksize - * into the on-disk inode when writing inodes out, instead of i_size. - * - * The only time when i_disksize and i_size may be different is when - * a truncate is in progress. The only things which change i_disksize - * are ext3_get_block (growth) and ext3_truncate (shrinkth). - */ - loff_t i_disksize; - - /* on-disk additional length */ - __u16 i_extra_isize; - - /* - * truncate_mutex is for serialising ext3_truncate() against - * ext3_getblock(). In the 2.4 ext2 design, great chunks of inode's - * data tree are chopped off during truncate. We can't do that in - * ext3 because whenever we perform intermediate commits during - * truncate, the inode and all the metadata blocks *must* be in a - * consistent state which allows truncation of the orphans to restart - * during recovery. Hence we must fix the get_block-vs-truncate race - * by other means, so we have truncate_mutex. - */ - struct mutex truncate_mutex; - - /* - * Transactions that contain inode's metadata needed to complete - * fsync and fdatasync, respectively. - */ - atomic_t i_sync_tid; - atomic_t i_datasync_tid; - - struct inode vfs_inode; -}; - -#endif /* _LINUX_EXT3_FS_I */ diff --git a/include/linux/ext3_fs_sb.h b/include/linux/ext3_fs_sb.h deleted file mode 100644 index 64365252f1b..00000000000 --- a/include/linux/ext3_fs_sb.h +++ /dev/null @@ -1,91 +0,0 @@ -/* - * linux/include/linux/ext3_fs_sb.h - * - * Copyright (C) 1992, 1993, 1994, 1995 - * Remy Card (card@masi.ibp.fr) - * Laboratoire MASI - Institut Blaise Pascal - * Universite Pierre et Marie Curie (Paris VI) - * - * from - * - * linux/include/linux/minix_fs_sb.h - * - * Copyright (C) 1991, 1992 Linus Torvalds - */ - -#ifndef _LINUX_EXT3_FS_SB -#define _LINUX_EXT3_FS_SB - -#ifdef __KERNEL__ -#include <linux/timer.h> -#include <linux/wait.h> -#include <linux/blockgroup_lock.h> -#include <linux/percpu_counter.h> -#endif -#include <linux/rbtree.h> - -/* - * third extended-fs super-block data in memory - */ -struct ext3_sb_info { - unsigned long s_frag_size; /* Size of a fragment in bytes */ - unsigned long s_frags_per_block;/* Number of fragments per block */ - unsigned long s_inodes_per_block;/* Number of inodes per block */ - unsigned long s_frags_per_group;/* Number of fragments in a group */ - unsigned long s_blocks_per_group;/* Number of blocks in a group */ - unsigned long s_inodes_per_group;/* Number of inodes in a group */ - unsigned long s_itb_per_group; /* Number of inode table blocks per group */ - unsigned long s_gdb_count; /* Number of group descriptor blocks */ - unsigned long s_desc_per_block; /* Number of group descriptors per block */ - unsigned long s_groups_count; /* Number of groups in the fs */ - unsigned long s_overhead_last; /* Last calculated overhead */ - unsigned long s_blocks_last; /* Last seen block count */ - struct buffer_head * s_sbh; /* Buffer containing the super block */ - struct ext3_super_block * s_es; /* Pointer to the super block in the buffer */ - struct buffer_head ** s_group_desc; - unsigned long s_mount_opt; - ext3_fsblk_t s_sb_block; - uid_t s_resuid; - gid_t s_resgid; - unsigned short s_mount_state; - unsigned short s_pad; - int s_addr_per_block_bits; - int s_desc_per_block_bits; - int s_inode_size; - int s_first_ino; - spinlock_t s_next_gen_lock; - u32 s_next_generation; - u32 s_hash_seed[4]; - int s_def_hash_version; - int s_hash_unsigned; /* 3 if hash should be signed, 0 if not */ - struct percpu_counter s_freeblocks_counter; - struct percpu_counter s_freeinodes_counter; - struct percpu_counter s_dirs_counter; - struct blockgroup_lock *s_blockgroup_lock; - - /* root of the per fs reservation window tree */ - spinlock_t s_rsv_window_lock; - struct rb_root s_rsv_window_root; - struct ext3_reserve_window_node s_rsv_window_head; - - /* Journaling */ - struct inode * s_journal_inode; - struct journal_s * s_journal; - struct list_head s_orphan; - struct mutex s_orphan_lock; - struct mutex s_resize_lock; - unsigned long s_commit_interval; - struct block_device *journal_bdev; -#ifdef CONFIG_QUOTA - char *s_qf_names[MAXQUOTAS]; /* Names of quota files with journalled quota */ - int s_jquota_fmt; /* Format of quota to use */ -#endif -}; - -static inline spinlock_t * -sb_bgl_lock(struct ext3_sb_info *sbi, unsigned int block_group) -{ - return bgl_lock_ptr(sbi->s_blockgroup_lock, block_group); -} - -#endif /* _LINUX_EXT3_FS_SB */ diff --git a/include/linux/ext3_jbd.h b/include/linux/ext3_jbd.h deleted file mode 100644 index d7b5ddca99c..00000000000 --- a/include/linux/ext3_jbd.h +++ /dev/null @@ -1,229 +0,0 @@ -/* - * linux/include/linux/ext3_jbd.h - * - * Written by Stephen C. Tweedie <sct@redhat.com>, 1999 - * - * Copyright 1998--1999 Red Hat corp --- All Rights Reserved - * - * This file is part of the Linux kernel and is made available under - * the terms of the GNU General Public License, version 2, or at your - * option, any later version, incorporated herein by reference. - * - * Ext3-specific journaling extensions. - */ - -#ifndef _LINUX_EXT3_JBD_H -#define _LINUX_EXT3_JBD_H - -#include <linux/fs.h> -#include <linux/jbd.h> -#include <linux/ext3_fs.h> - -#define EXT3_JOURNAL(inode) (EXT3_SB((inode)->i_sb)->s_journal) - -/* Define the number of blocks we need to account to a transaction to - * modify one block of data. - * - * We may have to touch one inode, one bitmap buffer, up to three - * indirection blocks, the group and superblock summaries, and the data - * block to complete the transaction. */ - -#define EXT3_SINGLEDATA_TRANS_BLOCKS 8U - -/* Extended attribute operations touch at most two data buffers, - * two bitmap buffers, and two group summaries, in addition to the inode - * and the superblock, which are already accounted for. */ - -#define EXT3_XATTR_TRANS_BLOCKS 6U - -/* Define the minimum size for a transaction which modifies data. This - * needs to take into account the fact that we may end up modifying two - * quota files too (one for the group, one for the user quota). The - * superblock only gets updated once, of course, so don't bother - * counting that again for the quota updates. */ - -#define EXT3_DATA_TRANS_BLOCKS(sb) (EXT3_SINGLEDATA_TRANS_BLOCKS + \ - EXT3_XATTR_TRANS_BLOCKS - 2 + \ - EXT3_MAXQUOTAS_TRANS_BLOCKS(sb)) - -/* Delete operations potentially hit one directory's namespace plus an - * entire inode, plus arbitrary amounts of bitmap/indirection data. Be - * generous. We can grow the delete transaction later if necessary. */ - -#define EXT3_DELETE_TRANS_BLOCKS(sb) (EXT3_MAXQUOTAS_TRANS_BLOCKS(sb) + 64) - -/* Define an arbitrary limit for the amount of data we will anticipate - * writing to any given transaction. For unbounded transactions such as - * write(2) and truncate(2) we can write more than this, but we always - * start off at the maximum transaction size and grow the transaction - * optimistically as we go. */ - -#define EXT3_MAX_TRANS_DATA 64U - -/* We break up a large truncate or write transaction once the handle's - * buffer credits gets this low, we need either to extend the - * transaction or to start a new one. Reserve enough space here for - * inode, bitmap, superblock, group and indirection updates for at least - * one block, plus two quota updates. Quota allocations are not - * needed. */ - -#define EXT3_RESERVE_TRANS_BLOCKS 12U - -#define EXT3_INDEX_EXTRA_TRANS_BLOCKS 8 - -#ifdef CONFIG_QUOTA -/* Amount of blocks needed for quota update - we know that the structure was - * allocated so we need to update only inode+data */ -#define EXT3_QUOTA_TRANS_BLOCKS(sb) (test_opt(sb, QUOTA) ? 2 : 0) -/* Amount of blocks needed for quota insert/delete - we do some block writes - * but inode, sb and group updates are done only once */ -#define EXT3_QUOTA_INIT_BLOCKS(sb) (test_opt(sb, QUOTA) ? (DQUOT_INIT_ALLOC*\ - (EXT3_SINGLEDATA_TRANS_BLOCKS-3)+3+DQUOT_INIT_REWRITE) : 0) -#define EXT3_QUOTA_DEL_BLOCKS(sb) (test_opt(sb, QUOTA) ? (DQUOT_DEL_ALLOC*\ - (EXT3_SINGLEDATA_TRANS_BLOCKS-3)+3+DQUOT_DEL_REWRITE) : 0) -#else -#define EXT3_QUOTA_TRANS_BLOCKS(sb) 0 -#define EXT3_QUOTA_INIT_BLOCKS(sb) 0 -#define EXT3_QUOTA_DEL_BLOCKS(sb) 0 -#endif -#define EXT3_MAXQUOTAS_TRANS_BLOCKS(sb) (MAXQUOTAS*EXT3_QUOTA_TRANS_BLOCKS(sb)) -#define EXT3_MAXQUOTAS_INIT_BLOCKS(sb) (MAXQUOTAS*EXT3_QUOTA_INIT_BLOCKS(sb)) -#define EXT3_MAXQUOTAS_DEL_BLOCKS(sb) (MAXQUOTAS*EXT3_QUOTA_DEL_BLOCKS(sb)) - -int -ext3_mark_iloc_dirty(handle_t *handle, - struct inode *inode, - struct ext3_iloc *iloc); - -/* - * On success, We end up with an outstanding reference count against - * iloc->bh. This _must_ be cleaned up later. - */ - -int ext3_reserve_inode_write(handle_t *handle, struct inode *inode, - struct ext3_iloc *iloc); - -int ext3_mark_inode_dirty(handle_t *handle, struct inode *inode); - -/* - * Wrapper functions with which ext3 calls into JBD. The intent here is - * to allow these to be turned into appropriate stubs so ext3 can control - * ext2 filesystems, so ext2+ext3 systems only nee one fs. This work hasn't - * been done yet. - */ - -static inline void ext3_journal_release_buffer(handle_t *handle, - struct buffer_head *bh) -{ - journal_release_buffer(handle, bh); -} - -void ext3_journal_abort_handle(const char *caller, const char *err_fn, - struct buffer_head *bh, handle_t *handle, int err); - -int __ext3_journal_get_undo_access(const char *where, handle_t *handle, - struct buffer_head *bh); - -int __ext3_journal_get_write_access(const char *where, handle_t *handle, - struct buffer_head *bh); - -int __ext3_journal_forget(const char *where, handle_t *handle, - struct buffer_head *bh); - -int __ext3_journal_revoke(const char *where, handle_t *handle, - unsigned long blocknr, struct buffer_head *bh); - -int __ext3_journal_get_create_access(const char *where, - handle_t *handle, struct buffer_head *bh); - -int __ext3_journal_dirty_metadata(const char *where, - handle_t *handle, struct buffer_head *bh); - -#define ext3_journal_get_undo_access(handle, bh) \ - __ext3_journal_get_undo_access(__func__, (handle), (bh)) -#define ext3_journal_get_write_access(handle, bh) \ - __ext3_journal_get_write_access(__func__, (handle), (bh)) -#define ext3_journal_revoke(handle, blocknr, bh) \ - __ext3_journal_revoke(__func__, (handle), (blocknr), (bh)) -#define ext3_journal_get_create_access(handle, bh) \ - __ext3_journal_get_create_access(__func__, (handle), (bh)) -#define ext3_journal_dirty_metadata(handle, bh) \ - __ext3_journal_dirty_metadata(__func__, (handle), (bh)) -#define ext3_journal_forget(handle, bh) \ - __ext3_journal_forget(__func__, (handle), (bh)) - -int ext3_journal_dirty_data(handle_t *handle, struct buffer_head *bh); - -handle_t *ext3_journal_start_sb(struct super_block *sb, int nblocks); -int __ext3_journal_stop(const char *where, handle_t *handle); - -static inline handle_t *ext3_journal_start(struct inode *inode, int nblocks) -{ - return ext3_journal_start_sb(inode->i_sb, nblocks); -} - -#define ext3_journal_stop(handle) \ - __ext3_journal_stop(__func__, (handle)) - -static inline handle_t *ext3_journal_current_handle(void) -{ - return journal_current_handle(); -} - -static inline int ext3_journal_extend(handle_t *handle, int nblocks) -{ - return journal_extend(handle, nblocks); -} - -static inline int ext3_journal_restart(handle_t *handle, int nblocks) -{ - return journal_restart(handle, nblocks); -} - -static inline int ext3_journal_blocks_per_page(struct inode *inode) -{ - return journal_blocks_per_page(inode); -} - -static inline int ext3_journal_force_commit(journal_t *journal) -{ - return journal_force_commit(journal); -} - -/* super.c */ -int ext3_force_commit(struct super_block *sb); - -static inline int ext3_should_journal_data(struct inode *inode) -{ - if (!S_ISREG(inode->i_mode)) - return 1; - if (test_opt(inode->i_sb, DATA_FLAGS) == EXT3_MOUNT_JOURNAL_DATA) - return 1; - if (EXT3_I(inode)->i_flags & EXT3_JOURNAL_DATA_FL) - return 1; - return 0; -} - -static inline int ext3_should_order_data(struct inode *inode) -{ - if (!S_ISREG(inode->i_mode)) - return 0; - if (EXT3_I(inode)->i_flags & EXT3_JOURNAL_DATA_FL) - return 0; - if (test_opt(inode->i_sb, DATA_FLAGS) == EXT3_MOUNT_ORDERED_DATA) - return 1; - return 0; -} - -static inline int ext3_should_writeback_data(struct inode *inode) -{ - if (!S_ISREG(inode->i_mode)) - return 0; - if (EXT3_I(inode)->i_flags & EXT3_JOURNAL_DATA_FL) - return 0; - if (test_opt(inode->i_sb, DATA_FLAGS) == EXT3_MOUNT_WRITEBACK_DATA) - return 1; - return 0; -} - -#endif /* _LINUX_EXT3_JBD_H */ diff --git a/include/linux/fdtable.h b/include/linux/fdtable.h index 82163c4b32c..158a41eed31 100644 --- a/include/linux/fdtable.h +++ b/include/linux/fdtable.h @@ -21,23 +21,45 @@ */ #define NR_OPEN_DEFAULT BITS_PER_LONG -/* - * The embedded_fd_set is a small fd_set, - * suitable for most tasks (which open <= BITS_PER_LONG files) - */ -struct embedded_fd_set { - unsigned long fds_bits[1]; -}; - struct fdtable { unsigned int max_fds; struct file __rcu **fd; /* current fd array */ - fd_set *close_on_exec; - fd_set *open_fds; + unsigned long *close_on_exec; + unsigned long *open_fds; struct rcu_head rcu; struct fdtable *next; }; +static inline void __set_close_on_exec(int fd, struct fdtable *fdt) +{ + __set_bit(fd, fdt->close_on_exec); +} + +static inline void __clear_close_on_exec(int fd, struct fdtable *fdt) +{ + __clear_bit(fd, fdt->close_on_exec); +} + +static inline bool close_on_exec(int fd, const struct fdtable *fdt) +{ + return test_bit(fd, fdt->close_on_exec); +} + +static inline void __set_open_fd(int fd, struct fdtable *fdt) +{ + __set_bit(fd, fdt->open_fds); +} + +static inline void __clear_open_fd(int fd, struct fdtable *fdt) +{ + __clear_bit(fd, fdt->open_fds); +} + +static inline bool fd_is_open(int fd, const struct fdtable *fdt) +{ + return test_bit(fd, fdt->open_fds); +} + /* * Open file table structure */ @@ -53,8 +75,8 @@ struct files_struct { */ spinlock_t file_lock ____cacheline_aligned_in_smp; int next_fd; - struct embedded_fd_set close_on_exec_init; - struct embedded_fd_set open_fds_init; + unsigned long close_on_exec_init[1]; + unsigned long open_fds_init[1]; struct file __rcu * fd_array[NR_OPEN_DEFAULT]; }; diff --git a/include/linux/firewire.h b/include/linux/firewire.h index 4db7b68f058..cdc9b719e9c 100644 --- a/include/linux/firewire.h +++ b/include/linux/firewire.h @@ -2,6 +2,7 @@ #define _LINUX_FIREWIRE_H #include <linux/completion.h> +#include <linux/device.h> #include <linux/dma-mapping.h> #include <linux/kernel.h> #include <linux/kref.h> @@ -64,8 +65,6 @@ #define CSR_MODEL 0x17 #define CSR_DIRECTORY_ID 0x20 -struct device; - struct fw_csr_iterator { const u32 *p; const u32 *end; diff --git a/include/linux/fs.h b/include/linux/fs.h index fa63f1b4610..135693e79f2 100644 --- a/include/linux/fs.h +++ b/include/linux/fs.h @@ -92,6 +92,10 @@ struct inodes_stat_t { /* File is opened using open(.., 3, ..) and is writeable only for ioctls (specialy hack for floppy.c) */ #define FMODE_WRITE_IOCTL ((__force fmode_t)0x100) +/* 32bit hashes as llseek() offset (for directories) */ +#define FMODE_32BITHASH ((__force fmode_t)0x200) +/* 64bit hashes as llseek() offset (for directories) */ +#define FMODE_64BITHASH ((__force fmode_t)0x400) /* * Don't update ctime and mtime. @@ -1872,19 +1876,6 @@ extern struct dentry *mount_pseudo(struct file_system_type *, char *, const struct dentry_operations *dops, unsigned long); -static inline void sb_mark_dirty(struct super_block *sb) -{ - sb->s_dirt = 1; -} -static inline void sb_mark_clean(struct super_block *sb) -{ - sb->s_dirt = 0; -} -static inline int sb_is_dirty(struct super_block *sb) -{ - return sb->s_dirt; -} - /* Alas, no aliases. Too much hassle with bringing module.h everywhere */ #define fops_get(fops) \ (((fops) && try_module_get((fops)->owner) ? (fops) : NULL)) diff --git a/include/linux/fsl/mxs-dma.h b/include/linux/fsl/mxs-dma.h new file mode 100644 index 00000000000..203d7c4a3e1 --- /dev/null +++ b/include/linux/fsl/mxs-dma.h @@ -0,0 +1,28 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __MACH_MXS_DMA_H__ +#define __MACH_MXS_DMA_H__ + +#include <linux/dmaengine.h> + +struct mxs_dma_data { + int chan_irq; +}; + +static inline int mxs_dma_is_apbh(struct dma_chan *chan) +{ + return !strcmp(dev_name(chan->device->dev), "mxs-dma-apbh"); +} + +static inline int mxs_dma_is_apbx(struct dma_chan *chan) +{ + return !strcmp(dev_name(chan->device->dev), "mxs-dma-apbx"); +} + +#endif /* __MACH_MXS_DMA_H__ */ diff --git a/include/linux/gpio.h b/include/linux/gpio.h index ed5a46707ad..6155ecf192b 100644 --- a/include/linux/gpio.h +++ b/include/linux/gpio.h @@ -14,6 +14,12 @@ #define GPIOF_OUT_INIT_LOW (GPIOF_DIR_OUT | GPIOF_INIT_LOW) #define GPIOF_OUT_INIT_HIGH (GPIOF_DIR_OUT | GPIOF_INIT_HIGH) +/* Gpio pin is open drain */ +#define GPIOF_OPEN_DRAIN (1 << 2) + +/* Gpio pin is open source */ +#define GPIOF_OPEN_SOURCE (1 << 3) + /** * struct gpio - a structure describing a GPIO with configuration * @gpio: the GPIO number diff --git a/include/linux/gpio_keys.h b/include/linux/gpio_keys.h index 004ff33ab38..a7e977ff4ab 100644 --- a/include/linux/gpio_keys.h +++ b/include/linux/gpio_keys.h @@ -6,7 +6,7 @@ struct device; struct gpio_keys_button { /* Configuration parameters */ unsigned int code; /* input event code (KEY_*, SW_*) */ - int gpio; + int gpio; /* -1 if this key does not support gpio */ int active_low; const char *desc; unsigned int type; /* input event type (EV_KEY, EV_SW, EV_ABS) */ @@ -14,6 +14,7 @@ struct gpio_keys_button { int debounce_interval; /* debounce ticks interval in msecs */ bool can_disable; int value; /* axis value for EV_ABS */ + unsigned int irq; /* Irq number in case of interrupt keys */ }; struct gpio_keys_platform_data { diff --git a/include/linux/hsi/Kbuild b/include/linux/hsi/Kbuild new file mode 100644 index 00000000000..271a770b478 --- /dev/null +++ b/include/linux/hsi/Kbuild @@ -0,0 +1 @@ +header-y += hsi_char.h diff --git a/include/linux/hsi/hsi.h b/include/linux/hsi/hsi.h new file mode 100644 index 00000000000..4b178067f40 --- /dev/null +++ b/include/linux/hsi/hsi.h @@ -0,0 +1,410 @@ +/* + * HSI core header file. + * + * Copyright (C) 2010 Nokia Corporation. All rights reserved. + * + * Contact: Carlos Chinea <carlos.chinea@nokia.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + */ + +#ifndef __LINUX_HSI_H__ +#define __LINUX_HSI_H__ + +#include <linux/device.h> +#include <linux/mutex.h> +#include <linux/scatterlist.h> +#include <linux/spinlock.h> +#include <linux/list.h> +#include <linux/module.h> + +/* HSI message ttype */ +#define HSI_MSG_READ 0 +#define HSI_MSG_WRITE 1 + +/* HSI configuration values */ +enum { + HSI_MODE_STREAM = 1, + HSI_MODE_FRAME, +}; + +enum { + HSI_FLOW_SYNC, /* Synchronized flow */ + HSI_FLOW_PIPE, /* Pipelined flow */ +}; + +enum { + HSI_ARB_RR, /* Round-robin arbitration */ + HSI_ARB_PRIO, /* Channel priority arbitration */ +}; + +#define HSI_MAX_CHANNELS 16 + +/* HSI message status codes */ +enum { + HSI_STATUS_COMPLETED, /* Message transfer is completed */ + HSI_STATUS_PENDING, /* Message pending to be read/write (POLL) */ + HSI_STATUS_PROCEEDING, /* Message transfer is ongoing */ + HSI_STATUS_QUEUED, /* Message waiting to be served */ + HSI_STATUS_ERROR, /* Error when message transfer was ongoing */ +}; + +/* HSI port event codes */ +enum { + HSI_EVENT_START_RX, + HSI_EVENT_STOP_RX, +}; + +/** + * struct hsi_config - Configuration for RX/TX HSI modules + * @mode: Bit transmission mode (STREAM or FRAME) + * @channels: Number of channels to use [1..16] + * @speed: Max bit transmission speed (Kbit/s) + * @flow: RX flow type (SYNCHRONIZED or PIPELINE) + * @arb_mode: Arbitration mode for TX frame (Round robin, priority) + */ +struct hsi_config { + unsigned int mode; + unsigned int channels; + unsigned int speed; + union { + unsigned int flow; /* RX only */ + unsigned int arb_mode; /* TX only */ + }; +}; + +/** + * struct hsi_board_info - HSI client board info + * @name: Name for the HSI device + * @hsi_id: HSI controller id where the client sits + * @port: Port number in the controller where the client sits + * @tx_cfg: HSI TX configuration + * @rx_cfg: HSI RX configuration + * @platform_data: Platform related data + * @archdata: Architecture-dependent device data + */ +struct hsi_board_info { + const char *name; + unsigned int hsi_id; + unsigned int port; + struct hsi_config tx_cfg; + struct hsi_config rx_cfg; + void *platform_data; + struct dev_archdata *archdata; +}; + +#ifdef CONFIG_HSI_BOARDINFO +extern int hsi_register_board_info(struct hsi_board_info const *info, + unsigned int len); +#else +static inline int hsi_register_board_info(struct hsi_board_info const *info, + unsigned int len) +{ + return 0; +} +#endif /* CONFIG_HSI_BOARDINFO */ + +/** + * struct hsi_client - HSI client attached to an HSI port + * @device: Driver model representation of the device + * @tx_cfg: HSI TX configuration + * @rx_cfg: HSI RX configuration + * @hsi_start_rx: Called after incoming wake line goes high + * @hsi_stop_rx: Called after incoming wake line goes low + */ +struct hsi_client { + struct device device; + struct hsi_config tx_cfg; + struct hsi_config rx_cfg; + void (*hsi_start_rx)(struct hsi_client *cl); + void (*hsi_stop_rx)(struct hsi_client *cl); + /* private: */ + unsigned int pclaimed:1; + struct list_head link; +}; + +#define to_hsi_client(dev) container_of(dev, struct hsi_client, device) + +static inline void hsi_client_set_drvdata(struct hsi_client *cl, void *data) +{ + dev_set_drvdata(&cl->device, data); +} + +static inline void *hsi_client_drvdata(struct hsi_client *cl) +{ + return dev_get_drvdata(&cl->device); +} + +/** + * struct hsi_client_driver - Driver associated to an HSI client + * @driver: Driver model representation of the driver + */ +struct hsi_client_driver { + struct device_driver driver; +}; + +#define to_hsi_client_driver(drv) container_of(drv, struct hsi_client_driver,\ + driver) + +int hsi_register_client_driver(struct hsi_client_driver *drv); + +static inline void hsi_unregister_client_driver(struct hsi_client_driver *drv) +{ + driver_unregister(&drv->driver); +} + +/** + * struct hsi_msg - HSI message descriptor + * @link: Free to use by the current descriptor owner + * @cl: HSI device client that issues the transfer + * @sgt: Head of the scatterlist array + * @context: Client context data associated to the transfer + * @complete: Transfer completion callback + * @destructor: Destructor to free resources when flushing + * @status: Status of the transfer when completed + * @actual_len: Actual length of data transfered on completion + * @channel: Channel were to TX/RX the message + * @ttype: Transfer type (TX if set, RX otherwise) + * @break_frame: if true HSI will send/receive a break frame. Data buffers are + * ignored in the request. + */ +struct hsi_msg { + struct list_head link; + struct hsi_client *cl; + struct sg_table sgt; + void *context; + + void (*complete)(struct hsi_msg *msg); + void (*destructor)(struct hsi_msg *msg); + + int status; + unsigned int actual_len; + unsigned int channel; + unsigned int ttype:1; + unsigned int break_frame:1; +}; + +struct hsi_msg *hsi_alloc_msg(unsigned int n_frag, gfp_t flags); +void hsi_free_msg(struct hsi_msg *msg); + +/** + * struct hsi_port - HSI port device + * @device: Driver model representation of the device + * @tx_cfg: Current TX path configuration + * @rx_cfg: Current RX path configuration + * @num: Port number + * @shared: Set when port can be shared by different clients + * @claimed: Reference count of clients which claimed the port + * @lock: Serialize port claim + * @async: Asynchronous transfer callback + * @setup: Callback to set the HSI client configuration + * @flush: Callback to clean the HW state and destroy all pending transfers + * @start_tx: Callback to inform that a client wants to TX data + * @stop_tx: Callback to inform that a client no longer wishes to TX data + * @release: Callback to inform that a client no longer uses the port + * @clients: List of hsi_clients using the port. + * @clock: Lock to serialize access to the clients list. + */ +struct hsi_port { + struct device device; + struct hsi_config tx_cfg; + struct hsi_config rx_cfg; + unsigned int num; + unsigned int shared:1; + int claimed; + struct mutex lock; + int (*async)(struct hsi_msg *msg); + int (*setup)(struct hsi_client *cl); + int (*flush)(struct hsi_client *cl); + int (*start_tx)(struct hsi_client *cl); + int (*stop_tx)(struct hsi_client *cl); + int (*release)(struct hsi_client *cl); + struct list_head clients; + spinlock_t clock; +}; + +#define to_hsi_port(dev) container_of(dev, struct hsi_port, device) +#define hsi_get_port(cl) to_hsi_port((cl)->device.parent) + +void hsi_event(struct hsi_port *port, unsigned int event); +int hsi_claim_port(struct hsi_client *cl, unsigned int share); +void hsi_release_port(struct hsi_client *cl); + +static inline int hsi_port_claimed(struct hsi_client *cl) +{ + return cl->pclaimed; +} + +static inline void hsi_port_set_drvdata(struct hsi_port *port, void *data) +{ + dev_set_drvdata(&port->device, data); +} + +static inline void *hsi_port_drvdata(struct hsi_port *port) +{ + return dev_get_drvdata(&port->device); +} + +/** + * struct hsi_controller - HSI controller device + * @device: Driver model representation of the device + * @owner: Pointer to the module owning the controller + * @id: HSI controller ID + * @num_ports: Number of ports in the HSI controller + * @port: Array of HSI ports + */ +struct hsi_controller { + struct device device; + struct module *owner; + unsigned int id; + unsigned int num_ports; + struct hsi_port *port; +}; + +#define to_hsi_controller(dev) container_of(dev, struct hsi_controller, device) + +struct hsi_controller *hsi_alloc_controller(unsigned int n_ports, gfp_t flags); +void hsi_free_controller(struct hsi_controller *hsi); +int hsi_register_controller(struct hsi_controller *hsi); +void hsi_unregister_controller(struct hsi_controller *hsi); + +static inline void hsi_controller_set_drvdata(struct hsi_controller *hsi, + void *data) +{ + dev_set_drvdata(&hsi->device, data); +} + +static inline void *hsi_controller_drvdata(struct hsi_controller *hsi) +{ + return dev_get_drvdata(&hsi->device); +} + +static inline struct hsi_port *hsi_find_port_num(struct hsi_controller *hsi, + unsigned int num) +{ + return (num < hsi->num_ports) ? &hsi->port[num] : NULL; +} + +/* + * API for HSI clients + */ +int hsi_async(struct hsi_client *cl, struct hsi_msg *msg); + +/** + * hsi_id - Get HSI controller ID associated to a client + * @cl: Pointer to a HSI client + * + * Return the controller id where the client is attached to + */ +static inline unsigned int hsi_id(struct hsi_client *cl) +{ + return to_hsi_controller(cl->device.parent->parent)->id; +} + +/** + * hsi_port_id - Gets the port number a client is attached to + * @cl: Pointer to HSI client + * + * Return the port number associated to the client + */ +static inline unsigned int hsi_port_id(struct hsi_client *cl) +{ + return to_hsi_port(cl->device.parent)->num; +} + +/** + * hsi_setup - Configure the client's port + * @cl: Pointer to the HSI client + * + * When sharing ports, clients should either relay on a single + * client setup or have the same setup for all of them. + * + * Return -errno on failure, 0 on success + */ +static inline int hsi_setup(struct hsi_client *cl) +{ + if (!hsi_port_claimed(cl)) + return -EACCES; + return hsi_get_port(cl)->setup(cl); +} + +/** + * hsi_flush - Flush all pending transactions on the client's port + * @cl: Pointer to the HSI client + * + * This function will destroy all pending hsi_msg in the port and reset + * the HW port so it is ready to receive and transmit from a clean state. + * + * Return -errno on failure, 0 on success + */ +static inline int hsi_flush(struct hsi_client *cl) +{ + if (!hsi_port_claimed(cl)) + return -EACCES; + return hsi_get_port(cl)->flush(cl); +} + +/** + * hsi_async_read - Submit a read transfer + * @cl: Pointer to the HSI client + * @msg: HSI message descriptor of the transfer + * + * Return -errno on failure, 0 on success + */ +static inline int hsi_async_read(struct hsi_client *cl, struct hsi_msg *msg) +{ + msg->ttype = HSI_MSG_READ; + return hsi_async(cl, msg); +} + +/** + * hsi_async_write - Submit a write transfer + * @cl: Pointer to the HSI client + * @msg: HSI message descriptor of the transfer + * + * Return -errno on failure, 0 on success + */ +static inline int hsi_async_write(struct hsi_client *cl, struct hsi_msg *msg) +{ + msg->ttype = HSI_MSG_WRITE; + return hsi_async(cl, msg); +} + +/** + * hsi_start_tx - Signal the port that the client wants to start a TX + * @cl: Pointer to the HSI client + * + * Return -errno on failure, 0 on success + */ +static inline int hsi_start_tx(struct hsi_client *cl) +{ + if (!hsi_port_claimed(cl)) + return -EACCES; + return hsi_get_port(cl)->start_tx(cl); +} + +/** + * hsi_stop_tx - Signal the port that the client no longer wants to transmit + * @cl: Pointer to the HSI client + * + * Return -errno on failure, 0 on success + */ +static inline int hsi_stop_tx(struct hsi_client *cl) +{ + if (!hsi_port_claimed(cl)) + return -EACCES; + return hsi_get_port(cl)->stop_tx(cl); +} +#endif /* __LINUX_HSI_H__ */ diff --git a/include/linux/hsi/hsi_char.h b/include/linux/hsi/hsi_char.h new file mode 100644 index 00000000000..76160b4f455 --- /dev/null +++ b/include/linux/hsi/hsi_char.h @@ -0,0 +1,63 @@ +/* + * Part of the HSI character device driver. + * + * Copyright (C) 2010 Nokia Corporation. All rights reserved. + * + * Contact: Andras Domokos <andras.domokos at nokia.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + */ + + +#ifndef __HSI_CHAR_H +#define __HSI_CHAR_H + +#define HSI_CHAR_MAGIC 'k' +#define HSC_IOW(num, dtype) _IOW(HSI_CHAR_MAGIC, num, dtype) +#define HSC_IOR(num, dtype) _IOR(HSI_CHAR_MAGIC, num, dtype) +#define HSC_IOWR(num, dtype) _IOWR(HSI_CHAR_MAGIC, num, dtype) +#define HSC_IO(num) _IO(HSI_CHAR_MAGIC, num) + +#define HSC_RESET HSC_IO(16) +#define HSC_SET_PM HSC_IO(17) +#define HSC_SEND_BREAK HSC_IO(18) +#define HSC_SET_RX HSC_IOW(19, struct hsc_rx_config) +#define HSC_GET_RX HSC_IOW(20, struct hsc_rx_config) +#define HSC_SET_TX HSC_IOW(21, struct hsc_tx_config) +#define HSC_GET_TX HSC_IOW(22, struct hsc_tx_config) + +#define HSC_PM_DISABLE 0 +#define HSC_PM_ENABLE 1 + +#define HSC_MODE_STREAM 1 +#define HSC_MODE_FRAME 2 +#define HSC_FLOW_SYNC 0 +#define HSC_ARB_RR 0 +#define HSC_ARB_PRIO 1 + +struct hsc_rx_config { + uint32_t mode; + uint32_t flow; + uint32_t channels; +}; + +struct hsc_tx_config { + uint32_t mode; + uint32_t channels; + uint32_t speed; + uint32_t arb_mode; +}; + +#endif /* __HSI_CHAR_H */ diff --git a/include/linux/i2c-algo-bit.h b/include/linux/i2c-algo-bit.h index 584ffa0f328..63904ba6887 100644 --- a/include/linux/i2c-algo-bit.h +++ b/include/linux/i2c-algo-bit.h @@ -15,7 +15,8 @@ You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ + Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + MA 02110-1301 USA. */ /* ------------------------------------------------------------------------- */ /* With some changes from Kyösti Mälkki <kmalkki@cc.hut.fi> and even diff --git a/include/linux/i2c-algo-pcf.h b/include/linux/i2c-algo-pcf.h index 0f91a957a69..538e8f41a31 100644 --- a/include/linux/i2c-algo-pcf.h +++ b/include/linux/i2c-algo-pcf.h @@ -16,7 +16,8 @@ You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ + Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + MA 02110-1301 USA. */ /* ------------------------------------------------------------------------- */ /* With some changes from Kyösti Mälkki <kmalkki@cc.hut.fi> and even diff --git a/include/linux/i2c-dev.h b/include/linux/i2c-dev.h index fd53bfd2647..8a7406b2114 100644 --- a/include/linux/i2c-dev.h +++ b/include/linux/i2c-dev.h @@ -16,7 +16,8 @@ You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + MA 02110-1301 USA. */ #ifndef _LINUX_I2C_DEV_H diff --git a/include/linux/i2c-mux.h b/include/linux/i2c-mux.h index 34536effd65..747f0cde416 100644 --- a/include/linux/i2c-mux.h +++ b/include/linux/i2c-mux.h @@ -18,7 +18,8 @@ * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA. */ #ifndef _LINUX_I2C_MUX_H diff --git a/include/linux/i2c-smbus.h b/include/linux/i2c-smbus.h index 63f57a8c8b3..017fb40f702 100644 --- a/include/linux/i2c-smbus.h +++ b/include/linux/i2c-smbus.h @@ -15,7 +15,8 @@ * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA. */ #ifndef _LINUX_I2C_SMBUS_H diff --git a/include/linux/i2c.h b/include/linux/i2c.h index 8e25a9167f1..195d8b3d9cf 100644 --- a/include/linux/i2c.h +++ b/include/linux/i2c.h @@ -17,7 +17,8 @@ You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ + Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + MA 02110-1301 USA. */ /* ------------------------------------------------------------------------- */ /* With some changes from Kyösti Mälkki <kmalkki@cc.hut.fi> and diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h index 7fcab23c59c..2463b610033 100644 --- a/include/linux/i2c/twl.h +++ b/include/linux/i2c/twl.h @@ -761,7 +761,7 @@ struct twl_regulator_driver_data { /*----------------------------------------------------------------------*/ -int twl4030_sih_setup(int module); +int twl4030_sih_setup(struct device *dev, int module, int irq_base); /* Offsets to Power Registers */ #define TWL4030_VDAC_DEV_GRP 0x3B diff --git a/include/linux/ide.h b/include/linux/ide.h index 7afe15f916d..b17974917db 100644 --- a/include/linux/ide.h +++ b/include/linux/ide.h @@ -22,7 +22,6 @@ #include <acpi/acpi.h> #endif #include <asm/byteorder.h> -#include <asm/system.h> #include <asm/io.h> /* for request_sense */ diff --git a/include/linux/if_eql.h b/include/linux/if_eql.h index 79c4f268410..18a5d02a864 100644 --- a/include/linux/if_eql.h +++ b/include/linux/if_eql.h @@ -22,7 +22,7 @@ #define EQL_DEFAULT_SLAVE_PRIORITY 28800 #define EQL_DEFAULT_MAX_SLAVES 4 #define EQL_DEFAULT_MTU 576 -#define EQL_DEFAULT_RESCHED_IVAL 100 +#define EQL_DEFAULT_RESCHED_IVAL HZ #define EQL_ENSLAVE (SIOCDEVPRIVATE) #define EQL_EMANCIPATE (SIOCDEVPRIVATE + 1) diff --git a/include/linux/interrupt.h b/include/linux/interrupt.h index 3f830e00511..2aea5d22db0 100644 --- a/include/linux/interrupt.h +++ b/include/linux/interrupt.h @@ -19,7 +19,6 @@ #include <linux/atomic.h> #include <asm/ptrace.h> -#include <asm/system.h> /* * These correspond to the IORESOURCE_IRQ_* defines in diff --git a/include/linux/jbd2.h b/include/linux/jbd2.h index 5557baefed6..912c30a8ddb 100644 --- a/include/linux/jbd2.h +++ b/include/linux/jbd2.h @@ -971,6 +971,10 @@ extern void __journal_clean_data_list(transaction_t *transaction); /* Log buffer allocation */ extern struct journal_head * jbd2_journal_get_descriptor_buffer(journal_t *); int jbd2_journal_next_log_block(journal_t *, unsigned long long *); +int jbd2_journal_get_log_tail(journal_t *journal, tid_t *tid, + unsigned long *block); +void __jbd2_update_log_tail(journal_t *journal, tid_t tid, unsigned long block); +void jbd2_update_log_tail(journal_t *journal, tid_t tid, unsigned long block); /* Commit management */ extern void jbd2_journal_commit_transaction(journal_t *); @@ -1020,6 +1024,11 @@ jbd2_journal_write_metadata_buffer(transaction_t *transaction, /* Transaction locking */ extern void __wait_on_journal (journal_t *); +/* Transaction cache support */ +extern void jbd2_journal_destroy_transaction_cache(void); +extern int jbd2_journal_init_transaction_cache(void); +extern void jbd2_journal_free_transaction(transaction_t *); + /* * Journal locking. * @@ -1082,7 +1091,8 @@ extern int jbd2_journal_destroy (journal_t *); extern int jbd2_journal_recover (journal_t *journal); extern int jbd2_journal_wipe (journal_t *, int); extern int jbd2_journal_skip_recovery (journal_t *); -extern void jbd2_journal_update_superblock (journal_t *, int); +extern void jbd2_journal_update_sb_log_tail (journal_t *, tid_t, + unsigned long, int); extern void __jbd2_journal_abort_hard (journal_t *); extern void jbd2_journal_abort (journal_t *, int); extern int jbd2_journal_errno (journal_t *); diff --git a/include/linux/journal-head.h b/include/linux/journal-head.h index 423cb6d78ee..c18b46f8aee 100644 --- a/include/linux/journal-head.h +++ b/include/linux/journal-head.h @@ -66,6 +66,8 @@ struct journal_head { * transaction (if there is one). Only applies to buffers on a * transaction's data or metadata journaling list. * [j_list_lock] [jbd_lock_bh_state()] + * Either of these locks is enough for reading, both are needed for + * changes. */ transaction_t *b_transaction; diff --git a/include/linux/kernel.h b/include/linux/kernel.h index 92c10262d34..645231c373c 100644 --- a/include/linux/kernel.h +++ b/include/linux/kernel.h @@ -1,6 +1,8 @@ #ifndef _LINUX_KERNEL_H #define _LINUX_KERNEL_H +#include <linux/sysinfo.h> + /* * 'kernel.h' contains some often-used function prototypes etc */ @@ -701,27 +703,8 @@ static inline void ftrace_dump(enum ftrace_dump_mode oops_dump_mode) { } # define REBUILD_DUE_TO_FTRACE_MCOUNT_RECORD #endif -struct sysinfo; extern int do_sysinfo(struct sysinfo *info); #endif /* __KERNEL__ */ -#define SI_LOAD_SHIFT 16 -struct sysinfo { - long uptime; /* Seconds since boot */ - unsigned long loads[3]; /* 1, 5, and 15 minute load averages */ - unsigned long totalram; /* Total usable main memory size */ - unsigned long freeram; /* Available memory size */ - unsigned long sharedram; /* Amount of shared memory */ - unsigned long bufferram; /* Memory used by buffers */ - unsigned long totalswap; /* Total swap space size */ - unsigned long freeswap; /* swap space still available */ - unsigned short procs; /* Number of current processes */ - unsigned short pad; /* explicit padding for m68k */ - unsigned long totalhigh; /* Total high memory size */ - unsigned long freehigh; /* Available high memory size */ - unsigned int mem_unit; /* Memory unit size in bytes */ - char _f[20-2*sizeof(long)-sizeof(int)]; /* Padding: libc5 uses this.. */ -}; - #endif diff --git a/include/linux/kvm.h b/include/linux/kvm.h index 68e67e50d02..6c322a90b92 100644 --- a/include/linux/kvm.h +++ b/include/linux/kvm.h @@ -162,6 +162,7 @@ struct kvm_pit_config { #define KVM_EXIT_INTERNAL_ERROR 17 #define KVM_EXIT_OSI 18 #define KVM_EXIT_PAPR_HCALL 19 +#define KVM_EXIT_S390_UCONTROL 20 /* For KVM_EXIT_INTERNAL_ERROR */ #define KVM_INTERNAL_ERROR_EMULATION 1 @@ -249,6 +250,11 @@ struct kvm_run { #define KVM_S390_RESET_CPU_INIT 8 #define KVM_S390_RESET_IPL 16 __u64 s390_reset_flags; + /* KVM_EXIT_S390_UCONTROL */ + struct { + __u64 trans_exc_code; + __u32 pgm_code; + } s390_ucontrol; /* KVM_EXIT_DCR */ struct { __u32 dcrn; @@ -273,6 +279,20 @@ struct kvm_run { /* Fix the size of the union. */ char padding[256]; }; + + /* + * shared registers between kvm and userspace. + * kvm_valid_regs specifies the register classes set by the host + * kvm_dirty_regs specified the register classes dirtied by userspace + * struct kvm_sync_regs is architecture specific, as well as the + * bits for kvm_valid_regs and kvm_dirty_regs + */ + __u64 kvm_valid_regs; + __u64 kvm_dirty_regs; + union { + struct kvm_sync_regs regs; + char padding[1024]; + } s; }; /* for KVM_REGISTER_COALESCED_MMIO / KVM_UNREGISTER_COALESCED_MMIO */ @@ -431,6 +451,11 @@ struct kvm_ppc_pvinfo { #define KVMIO 0xAE +/* machine type bits, to be used as argument to KVM_CREATE_VM */ +#define KVM_VM_S390_UCONTROL 1 + +#define KVM_S390_SIE_PAGE_OFFSET 1 + /* * ioctls for /dev/kvm fds: */ @@ -555,9 +580,15 @@ struct kvm_ppc_pvinfo { #define KVM_CAP_PPC_SMT 64 #define KVM_CAP_PPC_RMA 65 #define KVM_CAP_MAX_VCPUS 66 /* returns max vcpus per vm */ +#define KVM_CAP_PPC_HIOR 67 #define KVM_CAP_PPC_PAPR 68 +#define KVM_CAP_SW_TLB 69 +#define KVM_CAP_ONE_REG 70 #define KVM_CAP_S390_GMAP 71 #define KVM_CAP_TSC_DEADLINE_TIMER 72 +#define KVM_CAP_S390_UCONTROL 73 +#define KVM_CAP_SYNC_REGS 74 +#define KVM_CAP_PCI_2_3 75 #ifdef KVM_CAP_IRQ_ROUTING @@ -637,6 +668,52 @@ struct kvm_clock_data { __u32 pad[9]; }; +#define KVM_MMU_FSL_BOOKE_NOHV 0 +#define KVM_MMU_FSL_BOOKE_HV 1 + +struct kvm_config_tlb { + __u64 params; + __u64 array; + __u32 mmu_type; + __u32 array_len; +}; + +struct kvm_dirty_tlb { + __u64 bitmap; + __u32 num_dirty; +}; + +/* Available with KVM_CAP_ONE_REG */ + +#define KVM_REG_ARCH_MASK 0xff00000000000000ULL +#define KVM_REG_GENERIC 0x0000000000000000ULL + +/* + * Architecture specific registers are to be defined in arch headers and + * ORed with the arch identifier. + */ +#define KVM_REG_PPC 0x1000000000000000ULL +#define KVM_REG_X86 0x2000000000000000ULL +#define KVM_REG_IA64 0x3000000000000000ULL +#define KVM_REG_ARM 0x4000000000000000ULL +#define KVM_REG_S390 0x5000000000000000ULL + +#define KVM_REG_SIZE_SHIFT 52 +#define KVM_REG_SIZE_MASK 0x00f0000000000000ULL +#define KVM_REG_SIZE_U8 0x0000000000000000ULL +#define KVM_REG_SIZE_U16 0x0010000000000000ULL +#define KVM_REG_SIZE_U32 0x0020000000000000ULL +#define KVM_REG_SIZE_U64 0x0030000000000000ULL +#define KVM_REG_SIZE_U128 0x0040000000000000ULL +#define KVM_REG_SIZE_U256 0x0050000000000000ULL +#define KVM_REG_SIZE_U512 0x0060000000000000ULL +#define KVM_REG_SIZE_U1024 0x0070000000000000ULL + +struct kvm_one_reg { + __u64 id; + __u64 addr; +}; + /* * ioctls for VM fds */ @@ -655,6 +732,17 @@ struct kvm_clock_data { struct kvm_userspace_memory_region) #define KVM_SET_TSS_ADDR _IO(KVMIO, 0x47) #define KVM_SET_IDENTITY_MAP_ADDR _IOW(KVMIO, 0x48, __u64) + +/* enable ucontrol for s390 */ +struct kvm_s390_ucas_mapping { + __u64 user_addr; + __u64 vcpu_addr; + __u64 length; +}; +#define KVM_S390_UCAS_MAP _IOW(KVMIO, 0x50, struct kvm_s390_ucas_mapping) +#define KVM_S390_UCAS_UNMAP _IOW(KVMIO, 0x51, struct kvm_s390_ucas_mapping) +#define KVM_S390_VCPU_FAULT _IOW(KVMIO, 0x52, unsigned long) + /* Device model IOC */ #define KVM_CREATE_IRQCHIP _IO(KVMIO, 0x60) #define KVM_IRQ_LINE _IOW(KVMIO, 0x61, struct kvm_irq_level) @@ -697,6 +785,9 @@ struct kvm_clock_data { /* Available with KVM_CAP_TSC_CONTROL */ #define KVM_SET_TSC_KHZ _IO(KVMIO, 0xa2) #define KVM_GET_TSC_KHZ _IO(KVMIO, 0xa3) +/* Available with KVM_CAP_PCI_2_3 */ +#define KVM_ASSIGN_SET_INTX_MASK _IOW(KVMIO, 0xa4, \ + struct kvm_assigned_pci_dev) /* * ioctls for vcpu fds @@ -763,8 +854,15 @@ struct kvm_clock_data { #define KVM_CREATE_SPAPR_TCE _IOW(KVMIO, 0xa8, struct kvm_create_spapr_tce) /* Available with KVM_CAP_RMA */ #define KVM_ALLOCATE_RMA _IOR(KVMIO, 0xa9, struct kvm_allocate_rma) +/* Available with KVM_CAP_SW_TLB */ +#define KVM_DIRTY_TLB _IOW(KVMIO, 0xaa, struct kvm_dirty_tlb) +/* Available with KVM_CAP_ONE_REG */ +#define KVM_GET_ONE_REG _IOW(KVMIO, 0xab, struct kvm_one_reg) +#define KVM_SET_ONE_REG _IOW(KVMIO, 0xac, struct kvm_one_reg) #define KVM_DEV_ASSIGN_ENABLE_IOMMU (1 << 0) +#define KVM_DEV_ASSIGN_PCI_2_3 (1 << 1) +#define KVM_DEV_ASSIGN_MASK_INTX (1 << 2) struct kvm_assigned_pci_dev { __u32 assigned_dev_id; diff --git a/include/linux/kvm_host.h b/include/linux/kvm_host.h index ca1b153585d..665a260c7e0 100644 --- a/include/linux/kvm_host.h +++ b/include/linux/kvm_host.h @@ -172,11 +172,6 @@ static inline int kvm_vcpu_exiting_guest_mode(struct kvm_vcpu *vcpu) */ #define KVM_MEM_MAX_NR_PAGES ((1UL << 31) - 1) -struct kvm_lpage_info { - unsigned long rmap_pde; - int write_count; -}; - struct kvm_memory_slot { gfn_t base_gfn; unsigned long npages; @@ -185,7 +180,7 @@ struct kvm_memory_slot { unsigned long *dirty_bitmap; unsigned long *dirty_bitmap_head; unsigned long nr_dirty_pages; - struct kvm_lpage_info *lpage_info[KVM_NR_PAGE_SIZES - 1]; + struct kvm_arch_memory_slot arch; unsigned long userspace_addr; int user_alloc; int id; @@ -377,6 +372,9 @@ int kvm_set_memory_region(struct kvm *kvm, int __kvm_set_memory_region(struct kvm *kvm, struct kvm_userspace_memory_region *mem, int user_alloc); +void kvm_arch_free_memslot(struct kvm_memory_slot *free, + struct kvm_memory_slot *dont); +int kvm_arch_create_memslot(struct kvm_memory_slot *slot, unsigned long npages); int kvm_arch_prepare_memory_region(struct kvm *kvm, struct kvm_memory_slot *memslot, struct kvm_memory_slot old, @@ -386,6 +384,7 @@ void kvm_arch_commit_memory_region(struct kvm *kvm, struct kvm_userspace_memory_region *mem, struct kvm_memory_slot old, int user_alloc); +bool kvm_largepages_enabled(void); void kvm_disable_largepages(void); void kvm_arch_flush_shadow(struct kvm *kvm); @@ -451,6 +450,7 @@ long kvm_arch_dev_ioctl(struct file *filp, unsigned int ioctl, unsigned long arg); long kvm_arch_vcpu_ioctl(struct file *filp, unsigned int ioctl, unsigned long arg); +int kvm_arch_vcpu_fault(struct kvm_vcpu *vcpu, struct vm_fault *vmf); int kvm_dev_ioctl_check_extension(long ext); @@ -521,7 +521,7 @@ static inline void kvm_arch_free_vm(struct kvm *kvm) } #endif -int kvm_arch_init_vm(struct kvm *kvm); +int kvm_arch_init_vm(struct kvm *kvm, unsigned long type); void kvm_arch_destroy_vm(struct kvm *kvm); void kvm_free_all_assigned_devices(struct kvm *kvm); void kvm_arch_sync_events(struct kvm *kvm); @@ -547,6 +547,7 @@ struct kvm_assigned_dev_kernel { unsigned int entries_nr; int host_irq; bool host_irq_disabled; + bool pci_2_3; struct msix_entry *host_msix_entries; int guest_irq; struct msix_entry *guest_msix_entries; @@ -556,6 +557,7 @@ struct kvm_assigned_dev_kernel { struct pci_dev *dev; struct kvm *kvm; spinlock_t intx_lock; + spinlock_t intx_mask_lock; char irq_name[32]; struct pci_saved_state *pci_saved_state; }; @@ -651,11 +653,43 @@ static inline void kvm_guest_exit(void) current->flags &= ~PF_VCPU; } +/* + * search_memslots() and __gfn_to_memslot() are here because they are + * used in non-modular code in arch/powerpc/kvm/book3s_hv_rm_mmu.c. + * gfn_to_memslot() itself isn't here as an inline because that would + * bloat other code too much. + */ +static inline struct kvm_memory_slot * +search_memslots(struct kvm_memslots *slots, gfn_t gfn) +{ + struct kvm_memory_slot *memslot; + + kvm_for_each_memslot(memslot, slots) + if (gfn >= memslot->base_gfn && + gfn < memslot->base_gfn + memslot->npages) + return memslot; + + return NULL; +} + +static inline struct kvm_memory_slot * +__gfn_to_memslot(struct kvm_memslots *slots, gfn_t gfn) +{ + return search_memslots(slots, gfn); +} + static inline int memslot_id(struct kvm *kvm, gfn_t gfn) { return gfn_to_memslot(kvm, gfn)->id; } +static inline gfn_t gfn_to_index(gfn_t gfn, gfn_t base_gfn, int level) +{ + /* KVM_HPAGE_GFN_SHIFT(PT_PAGE_TABLE_LEVEL) must be 0. */ + return (gfn >> KVM_HPAGE_GFN_SHIFT(level)) - + (base_gfn >> KVM_HPAGE_GFN_SHIFT(level)); +} + static inline unsigned long gfn_to_hva_memslot(struct kvm_memory_slot *slot, gfn_t gfn) { @@ -702,12 +736,16 @@ static inline int mmu_notifier_retry(struct kvm_vcpu *vcpu, unsigned long mmu_se if (unlikely(vcpu->kvm->mmu_notifier_count)) return 1; /* - * Both reads happen under the mmu_lock and both values are - * modified under mmu_lock, so there's no need of smb_rmb() - * here in between, otherwise mmu_notifier_count should be - * read before mmu_notifier_seq, see - * mmu_notifier_invalidate_range_end write side. + * Ensure the read of mmu_notifier_count happens before the read + * of mmu_notifier_seq. This interacts with the smp_wmb() in + * mmu_notifier_invalidate_range_end to make sure that the caller + * either sees the old (non-zero) value of mmu_notifier_count or + * the new (incremented) value of mmu_notifier_seq. + * PowerPC Book3s HV KVM calls this under a per-page lock + * rather than under kvm->mmu_lock, for scalability, so + * can't rely on kvm->mmu_lock to keep things ordered. */ + smp_rmb(); if (vcpu->kvm->mmu_notifier_seq != mmu_seq) return 1; return 0; @@ -770,6 +808,13 @@ static inline bool kvm_vcpu_is_bsp(struct kvm_vcpu *vcpu) { return vcpu->kvm->bsp_vcpu_id == vcpu->vcpu_id; } + +bool kvm_vcpu_compatible(struct kvm_vcpu *vcpu); + +#else + +static inline bool kvm_vcpu_compatible(struct kvm_vcpu *vcpu) { return true; } + #endif #ifdef __KVM_HAVE_DEVICE_ASSIGNMENT diff --git a/include/linux/llist.h b/include/linux/llist.h index 801b44b07aa..a5199f6d0e8 100644 --- a/include/linux/llist.h +++ b/include/linux/llist.h @@ -56,8 +56,7 @@ */ #include <linux/kernel.h> -#include <asm/system.h> -#include <asm/processor.h> +#include <asm/cmpxchg.h> struct llist_head { struct llist_node *first; diff --git a/include/linux/lp8727.h b/include/linux/lp8727.h index d21fa2865bf..ea98c6133d3 100644 --- a/include/linux/lp8727.h +++ b/include/linux/lp8727.h @@ -1,4 +1,7 @@ /* + * LP8727 Micro/Mini USB IC with integrated charger + * + * Copyright (C) 2011 Texas Instruments * Copyright (C) 2011 National Semiconductor * * This program is free software; you can redistribute it and/or modify @@ -32,13 +35,24 @@ enum lp8727_ichg { ICHG_1000mA, }; +/** + * struct lp8727_chg_param + * @eoc_level : end of charge level setting + * @ichg : charging current + */ struct lp8727_chg_param { - /* end of charge level setting */ enum lp8727_eoc_level eoc_level; - /* charging current */ enum lp8727_ichg ichg; }; +/** + * struct lp8727_platform_data + * @get_batt_present : check battery status - exists or not + * @get_batt_level : get battery voltage (mV) + * @get_batt_capacity : get battery capacity (%) + * @get_batt_temp : get battery temperature + * @ac, @usb : charging parameters each charger type + */ struct lp8727_platform_data { u8 (*get_batt_present)(void); u16 (*get_batt_level)(void); diff --git a/include/linux/lsm_audit.h b/include/linux/lsm_audit.h index 88e78dedc2e..eab507f2b1c 100644 --- a/include/linux/lsm_audit.h +++ b/include/linux/lsm_audit.h @@ -21,7 +21,6 @@ #include <linux/path.h> #include <linux/key.h> #include <linux/skbuff.h> -#include <asm/system.h> /* Auxiliary data to use in generating the audit record. */ diff --git a/include/linux/mfd/88pm860x.h b/include/linux/mfd/88pm860x.h index 92be3476c9f..84d071ade1d 100644 --- a/include/linux/mfd/88pm860x.h +++ b/include/linux/mfd/88pm860x.h @@ -263,6 +263,22 @@ enum { #define PM8607_PD_PREBIAS_MASK (0x1F << 0) #define PM8607_PD_PRECHG_MASK (7 << 5) +#define PM8606_REF_GP_OSC_OFF 0 +#define PM8606_REF_GP_OSC_ON 1 +#define PM8606_REF_GP_OSC_UNKNOWN 2 + +/* Clients of reference group and 8MHz oscillator in 88PM8606 */ +enum pm8606_ref_gp_and_osc_clients { + REF_GP_NO_CLIENTS = 0, + WLED1_DUTY = (1<<0), /*PF 0x02.7:0*/ + WLED2_DUTY = (1<<1), /*PF 0x04.7:0*/ + WLED3_DUTY = (1<<2), /*PF 0x06.7:0*/ + RGB1_ENABLE = (1<<3), /*PF 0x07.1*/ + RGB2_ENABLE = (1<<4), /*PF 0x07.2*/ + LDO_VBR_EN = (1<<5), /*PF 0x12.0*/ + REF_GP_MAX_CLIENT = 0xFFFF +}; + /* Interrupt Number in 88PM8607 */ enum { PM8607_IRQ_ONKEY, @@ -298,6 +314,7 @@ enum { struct pm860x_chip { struct device *dev; struct mutex irq_lock; + struct mutex osc_lock; struct i2c_client *client; struct i2c_client *companion; /* companion chip client */ struct regmap *regmap; @@ -305,12 +322,15 @@ struct pm860x_chip { int buck3_double; /* DVC ramp slope double */ unsigned short companion_addr; + unsigned short osc_vote; int id; int irq_mode; int irq_base; int core_irq; unsigned char chip_version; + unsigned char osc_status; + unsigned int wakeup_flag; }; enum { @@ -369,6 +389,9 @@ struct pm860x_platform_data { int num_regulators; }; +extern int pm8606_osc_enable(struct pm860x_chip *, unsigned short); +extern int pm8606_osc_disable(struct pm860x_chip *, unsigned short); + extern int pm860x_reg_read(struct i2c_client *, int); extern int pm860x_reg_write(struct i2c_client *, int, unsigned char); extern int pm860x_bulk_read(struct i2c_client *, int, int, unsigned char *); diff --git a/include/linux/mfd/abx500.h b/include/linux/mfd/abx500.h index e20dd6ead1d..ee96cd51d8b 100644 --- a/include/linux/mfd/abx500.h +++ b/include/linux/mfd/abx500.h @@ -34,13 +34,6 @@ struct device; #define AB5500_1_1 0x21 #define AB5500_2_0 0x24 -/* AB8500 CIDs*/ -#define AB8500_CUT1P0 0x10 -#define AB8500_CUT1P1 0x11 -#define AB8500_CUT2P0 0x20 -#define AB8500_CUT3P0 0x30 -#define AB8500_CUT3P3 0x33 - /* * AB3100, EVENTA1, A2 and A3 event register flags * these are catenated into a single 32-bit flag in the code @@ -153,6 +146,279 @@ struct abx500_init_settings { u8 setting; }; +/* Battery driver related data */ +/* + * ADC for the battery thermistor. + * When using the ABx500_ADC_THERM_BATCTRL the battery ID resistor is combined + * with a NTC resistor to both identify the battery and to measure its + * temperature. Different phone manufactures uses different techniques to both + * identify the battery and to read its temperature. + */ +enum abx500_adc_therm { + ABx500_ADC_THERM_BATCTRL, + ABx500_ADC_THERM_BATTEMP, +}; + +/** + * struct abx500_res_to_temp - defines one point in a temp to res curve. To + * be used in battery packs that combines the identification resistor with a + * NTC resistor. + * @temp: battery pack temperature in Celcius + * @resist: NTC resistor net total resistance + */ +struct abx500_res_to_temp { + int temp; + int resist; +}; + +/** + * struct abx500_v_to_cap - Table for translating voltage to capacity + * @voltage: Voltage in mV + * @capacity: Capacity in percent + */ +struct abx500_v_to_cap { + int voltage; + int capacity; +}; + +/* Forward declaration */ +struct abx500_fg; + +/** + * struct abx500_fg_parameters - Fuel gauge algorithm parameters, in seconds + * if not specified + * @recovery_sleep_timer: Time between measurements while recovering + * @recovery_total_time: Total recovery time + * @init_timer: Measurement interval during startup + * @init_discard_time: Time we discard voltage measurement at startup + * @init_total_time: Total init time during startup + * @high_curr_time: Time current has to be high to go to recovery + * @accu_charging: FG accumulation time while charging + * @accu_high_curr: FG accumulation time in high current mode + * @high_curr_threshold: High current threshold, in mA + * @lowbat_threshold: Low battery threshold, in mV + * @overbat_threshold: Over battery threshold, in mV + * @battok_falling_th_sel0 Threshold in mV for battOk signal sel0 + * Resolution in 50 mV step. + * @battok_raising_th_sel1 Threshold in mV for battOk signal sel1 + * Resolution in 50 mV step. + * @user_cap_limit Capacity reported from user must be within this + * limit to be considered as sane, in percentage + * points. + * @maint_thres This is the threshold where we stop reporting + * battery full while in maintenance, in per cent + */ +struct abx500_fg_parameters { + int recovery_sleep_timer; + int recovery_total_time; + int init_timer; + int init_discard_time; + int init_total_time; + int high_curr_time; + int accu_charging; + int accu_high_curr; + int high_curr_threshold; + int lowbat_threshold; + int overbat_threshold; + int battok_falling_th_sel0; + int battok_raising_th_sel1; + int user_cap_limit; + int maint_thres; +}; + +/** + * struct abx500_charger_maximization - struct used by the board config. + * @use_maxi: Enable maximization for this battery type + * @maxi_chg_curr: Maximum charger current allowed + * @maxi_wait_cycles: cycles to wait before setting charger current + * @charger_curr_step delta between two charger current settings (mA) + */ +struct abx500_maxim_parameters { + bool ena_maxi; + int chg_curr; + int wait_cycles; + int charger_curr_step; +}; + +/** + * struct abx500_battery_type - different batteries supported + * @name: battery technology + * @resis_high: battery upper resistance limit + * @resis_low: battery lower resistance limit + * @charge_full_design: Maximum battery capacity in mAh + * @nominal_voltage: Nominal voltage of the battery in mV + * @termination_vol: max voltage upto which battery can be charged + * @termination_curr battery charging termination current in mA + * @recharge_vol battery voltage limit that will trigger a new + * full charging cycle in the case where maintenan- + * -ce charging has been disabled + * @normal_cur_lvl: charger current in normal state in mA + * @normal_vol_lvl: charger voltage in normal state in mV + * @maint_a_cur_lvl: charger current in maintenance A state in mA + * @maint_a_vol_lvl: charger voltage in maintenance A state in mV + * @maint_a_chg_timer_h: charge time in maintenance A state + * @maint_b_cur_lvl: charger current in maintenance B state in mA + * @maint_b_vol_lvl: charger voltage in maintenance B state in mV + * @maint_b_chg_timer_h: charge time in maintenance B state + * @low_high_cur_lvl: charger current in temp low/high state in mA + * @low_high_vol_lvl: charger voltage in temp low/high state in mV' + * @battery_resistance: battery inner resistance in mOhm. + * @n_r_t_tbl_elements: number of elements in r_to_t_tbl + * @r_to_t_tbl: table containing resistance to temp points + * @n_v_cap_tbl_elements: number of elements in v_to_cap_tbl + * @v_to_cap_tbl: Voltage to capacity (in %) table + * @n_batres_tbl_elements number of elements in the batres_tbl + * @batres_tbl battery internal resistance vs temperature table + */ +struct abx500_battery_type { + int name; + int resis_high; + int resis_low; + int charge_full_design; + int nominal_voltage; + int termination_vol; + int termination_curr; + int recharge_vol; + int normal_cur_lvl; + int normal_vol_lvl; + int maint_a_cur_lvl; + int maint_a_vol_lvl; + int maint_a_chg_timer_h; + int maint_b_cur_lvl; + int maint_b_vol_lvl; + int maint_b_chg_timer_h; + int low_high_cur_lvl; + int low_high_vol_lvl; + int battery_resistance; + int n_temp_tbl_elements; + struct abx500_res_to_temp *r_to_t_tbl; + int n_v_cap_tbl_elements; + struct abx500_v_to_cap *v_to_cap_tbl; + int n_batres_tbl_elements; + struct batres_vs_temp *batres_tbl; +}; + +/** + * struct abx500_bm_capacity_levels - abx500 capacity level data + * @critical: critical capacity level in percent + * @low: low capacity level in percent + * @normal: normal capacity level in percent + * @high: high capacity level in percent + * @full: full capacity level in percent + */ +struct abx500_bm_capacity_levels { + int critical; + int low; + int normal; + int high; + int full; +}; + +/** + * struct abx500_bm_charger_parameters - Charger specific parameters + * @usb_volt_max: maximum allowed USB charger voltage in mV + * @usb_curr_max: maximum allowed USB charger current in mA + * @ac_volt_max: maximum allowed AC charger voltage in mV + * @ac_curr_max: maximum allowed AC charger current in mA + */ +struct abx500_bm_charger_parameters { + int usb_volt_max; + int usb_curr_max; + int ac_volt_max; + int ac_curr_max; +}; + +/** + * struct abx500_bm_data - abx500 battery management data + * @temp_under under this temp, charging is stopped + * @temp_low between this temp and temp_under charging is reduced + * @temp_high between this temp and temp_over charging is reduced + * @temp_over over this temp, charging is stopped + * @temp_now present battery temperature + * @temp_interval_chg temperature measurement interval in s when charging + * @temp_interval_nochg temperature measurement interval in s when not charging + * @main_safety_tmr_h safety timer for main charger + * @usb_safety_tmr_h safety timer for usb charger + * @bkup_bat_v voltage which we charge the backup battery with + * @bkup_bat_i current which we charge the backup battery with + * @no_maintenance indicates that maintenance charging is disabled + * @abx500_adc_therm placement of thermistor, batctrl or battemp adc + * @chg_unknown_bat flag to enable charging of unknown batteries + * @enable_overshoot flag to enable VBAT overshoot control + * @auto_trig flag to enable auto adc trigger + * @fg_res resistance of FG resistor in 0.1mOhm + * @n_btypes number of elements in array bat_type + * @batt_id index of the identified battery in array bat_type + * @interval_charging charge alg cycle period time when charging (sec) + * @interval_not_charging charge alg cycle period time when not charging (sec) + * @temp_hysteresis temperature hysteresis + * @gnd_lift_resistance Battery ground to phone ground resistance (mOhm) + * @maxi: maximization parameters + * @cap_levels capacity in percent for the different capacity levels + * @bat_type table of supported battery types + * @chg_params charger parameters + * @fg_params fuel gauge parameters + */ +struct abx500_bm_data { + int temp_under; + int temp_low; + int temp_high; + int temp_over; + int temp_now; + int temp_interval_chg; + int temp_interval_nochg; + int main_safety_tmr_h; + int usb_safety_tmr_h; + int bkup_bat_v; + int bkup_bat_i; + bool no_maintenance; + bool chg_unknown_bat; + bool enable_overshoot; + bool auto_trig; + enum abx500_adc_therm adc_therm; + int fg_res; + int n_btypes; + int batt_id; + int interval_charging; + int interval_not_charging; + int temp_hysteresis; + int gnd_lift_resistance; + const struct abx500_maxim_parameters *maxi; + const struct abx500_bm_capacity_levels *cap_levels; + const struct abx500_battery_type *bat_type; + const struct abx500_bm_charger_parameters *chg_params; + const struct abx500_fg_parameters *fg_params; +}; + +struct abx500_chargalg_platform_data { + char **supplied_to; + size_t num_supplicants; +}; + +struct abx500_charger_platform_data { + char **supplied_to; + size_t num_supplicants; + bool autopower_cfg; +}; + +struct abx500_btemp_platform_data { + char **supplied_to; + size_t num_supplicants; +}; + +struct abx500_fg_platform_data { + char **supplied_to; + size_t num_supplicants; +}; + +struct abx500_bm_plat_data { + struct abx500_bm_data *battery; + struct abx500_charger_platform_data *charger; + struct abx500_btemp_platform_data *btemp; + struct abx500_fg_platform_data *fg; + struct abx500_chargalg_platform_data *chargalg; +}; + int abx500_set_register_interruptible(struct device *dev, u8 bank, u8 reg, u8 value); int abx500_get_register_interruptible(struct device *dev, u8 bank, u8 reg, diff --git a/include/linux/mfd/abx500/ab8500-bm.h b/include/linux/mfd/abx500/ab8500-bm.h new file mode 100644 index 00000000000..44310c98ee6 --- /dev/null +++ b/include/linux/mfd/abx500/ab8500-bm.h @@ -0,0 +1,474 @@ +/* + * Copyright ST-Ericsson 2012. + * + * Author: Arun Murthy <arun.murthy@stericsson.com> + * Licensed under GPLv2. + */ + +#ifndef _AB8500_BM_H +#define _AB8500_BM_H + +#include <linux/kernel.h> +#include <linux/mfd/abx500.h> + +/* + * System control 2 register offsets. + * bank = 0x02 + */ +#define AB8500_MAIN_WDOG_CTRL_REG 0x01 +#define AB8500_LOW_BAT_REG 0x03 +#define AB8500_BATT_OK_REG 0x04 +/* + * USB/ULPI register offsets + * Bank : 0x5 + */ +#define AB8500_USB_LINE_STAT_REG 0x80 + +/* + * Charger / status register offfsets + * Bank : 0x0B + */ +#define AB8500_CH_STATUS1_REG 0x00 +#define AB8500_CH_STATUS2_REG 0x01 +#define AB8500_CH_USBCH_STAT1_REG 0x02 +#define AB8500_CH_USBCH_STAT2_REG 0x03 +#define AB8500_CH_FSM_STAT_REG 0x04 +#define AB8500_CH_STAT_REG 0x05 + +/* + * Charger / control register offfsets + * Bank : 0x0B + */ +#define AB8500_CH_VOLT_LVL_REG 0x40 +#define AB8500_CH_VOLT_LVL_MAX_REG 0x41 /*Only in Cut2.0*/ +#define AB8500_CH_OPT_CRNTLVL_REG 0x42 +#define AB8500_CH_OPT_CRNTLVL_MAX_REG 0x43 /*Only in Cut2.0*/ +#define AB8500_CH_WD_TIMER_REG 0x50 +#define AB8500_CHARG_WD_CTRL 0x51 +#define AB8500_BTEMP_HIGH_TH 0x52 +#define AB8500_LED_INDICATOR_PWM_CTRL 0x53 +#define AB8500_LED_INDICATOR_PWM_DUTY 0x54 +#define AB8500_BATT_OVV 0x55 +#define AB8500_CHARGER_CTRL 0x56 +#define AB8500_BAT_CTRL_CURRENT_SOURCE 0x60 /*Only in Cut2.0*/ + +/* + * Charger / main control register offsets + * Bank : 0x0B + */ +#define AB8500_MCH_CTRL1 0x80 +#define AB8500_MCH_CTRL2 0x81 +#define AB8500_MCH_IPT_CURLVL_REG 0x82 +#define AB8500_CH_WD_REG 0x83 + +/* + * Charger / USB control register offsets + * Bank : 0x0B + */ +#define AB8500_USBCH_CTRL1_REG 0xC0 +#define AB8500_USBCH_CTRL2_REG 0xC1 +#define AB8500_USBCH_IPT_CRNTLVL_REG 0xC2 + +/* + * Gas Gauge register offsets + * Bank : 0x0C + */ +#define AB8500_GASG_CC_CTRL_REG 0x00 +#define AB8500_GASG_CC_ACCU1_REG 0x01 +#define AB8500_GASG_CC_ACCU2_REG 0x02 +#define AB8500_GASG_CC_ACCU3_REG 0x03 +#define AB8500_GASG_CC_ACCU4_REG 0x04 +#define AB8500_GASG_CC_SMPL_CNTRL_REG 0x05 +#define AB8500_GASG_CC_SMPL_CNTRH_REG 0x06 +#define AB8500_GASG_CC_SMPL_CNVL_REG 0x07 +#define AB8500_GASG_CC_SMPL_CNVH_REG 0x08 +#define AB8500_GASG_CC_CNTR_AVGOFF_REG 0x09 +#define AB8500_GASG_CC_OFFSET_REG 0x0A +#define AB8500_GASG_CC_NCOV_ACCU 0x10 +#define AB8500_GASG_CC_NCOV_ACCU_CTRL 0x11 +#define AB8500_GASG_CC_NCOV_ACCU_LOW 0x12 +#define AB8500_GASG_CC_NCOV_ACCU_MED 0x13 +#define AB8500_GASG_CC_NCOV_ACCU_HIGH 0x14 + +/* + * Interrupt register offsets + * Bank : 0x0E + */ +#define AB8500_IT_SOURCE2_REG 0x01 +#define AB8500_IT_SOURCE21_REG 0x14 + +/* + * RTC register offsets + * Bank: 0x0F + */ +#define AB8500_RTC_BACKUP_CHG_REG 0x0C +#define AB8500_RTC_CC_CONF_REG 0x01 +#define AB8500_RTC_CTRL_REG 0x0B + +/* + * OTP register offsets + * Bank : 0x15 + */ +#define AB8500_OTP_CONF_15 0x0E + +/* GPADC constants from AB8500 spec, UM0836 */ +#define ADC_RESOLUTION 1024 +#define ADC_CH_MAIN_MIN 0 +#define ADC_CH_MAIN_MAX 20030 +#define ADC_CH_VBUS_MIN 0 +#define ADC_CH_VBUS_MAX 20030 +#define ADC_CH_VBAT_MIN 2300 +#define ADC_CH_VBAT_MAX 4800 +#define ADC_CH_BKBAT_MIN 0 +#define ADC_CH_BKBAT_MAX 3200 + +/* Main charge i/p current */ +#define MAIN_CH_IP_CUR_0P9A 0x80 +#define MAIN_CH_IP_CUR_1P0A 0x90 +#define MAIN_CH_IP_CUR_1P1A 0xA0 +#define MAIN_CH_IP_CUR_1P2A 0xB0 +#define MAIN_CH_IP_CUR_1P3A 0xC0 +#define MAIN_CH_IP_CUR_1P4A 0xD0 +#define MAIN_CH_IP_CUR_1P5A 0xE0 + +/* ChVoltLevel */ +#define CH_VOL_LVL_3P5 0x00 +#define CH_VOL_LVL_4P0 0x14 +#define CH_VOL_LVL_4P05 0x16 +#define CH_VOL_LVL_4P1 0x1B +#define CH_VOL_LVL_4P15 0x20 +#define CH_VOL_LVL_4P2 0x25 +#define CH_VOL_LVL_4P6 0x4D + +/* ChOutputCurrentLevel */ +#define CH_OP_CUR_LVL_0P1 0x00 +#define CH_OP_CUR_LVL_0P2 0x01 +#define CH_OP_CUR_LVL_0P3 0x02 +#define CH_OP_CUR_LVL_0P4 0x03 +#define CH_OP_CUR_LVL_0P5 0x04 +#define CH_OP_CUR_LVL_0P6 0x05 +#define CH_OP_CUR_LVL_0P7 0x06 +#define CH_OP_CUR_LVL_0P8 0x07 +#define CH_OP_CUR_LVL_0P9 0x08 +#define CH_OP_CUR_LVL_1P4 0x0D +#define CH_OP_CUR_LVL_1P5 0x0E +#define CH_OP_CUR_LVL_1P6 0x0F + +/* BTEMP High thermal limits */ +#define BTEMP_HIGH_TH_57_0 0x00 +#define BTEMP_HIGH_TH_52 0x01 +#define BTEMP_HIGH_TH_57_1 0x02 +#define BTEMP_HIGH_TH_62 0x03 + +/* current is mA */ +#define USB_0P1A 100 +#define USB_0P2A 200 +#define USB_0P3A 300 +#define USB_0P4A 400 +#define USB_0P5A 500 + +#define LOW_BAT_3P1V 0x20 +#define LOW_BAT_2P3V 0x00 +#define LOW_BAT_RESET 0x01 +#define LOW_BAT_ENABLE 0x01 + +/* Backup battery constants */ +#define BUP_ICH_SEL_50UA 0x00 +#define BUP_ICH_SEL_150UA 0x04 +#define BUP_ICH_SEL_300UA 0x08 +#define BUP_ICH_SEL_700UA 0x0C + +#define BUP_VCH_SEL_2P5V 0x00 +#define BUP_VCH_SEL_2P6V 0x01 +#define BUP_VCH_SEL_2P8V 0x02 +#define BUP_VCH_SEL_3P1V 0x03 + +/* Battery OVV constants */ +#define BATT_OVV_ENA 0x02 +#define BATT_OVV_TH_3P7 0x00 +#define BATT_OVV_TH_4P75 0x01 + +/* A value to indicate over voltage */ +#define BATT_OVV_VALUE 4750 + +/* VBUS OVV constants */ +#define VBUS_OVV_SELECT_MASK 0x78 +#define VBUS_OVV_SELECT_5P6V 0x00 +#define VBUS_OVV_SELECT_5P7V 0x08 +#define VBUS_OVV_SELECT_5P8V 0x10 +#define VBUS_OVV_SELECT_5P9V 0x18 +#define VBUS_OVV_SELECT_6P0V 0x20 +#define VBUS_OVV_SELECT_6P1V 0x28 +#define VBUS_OVV_SELECT_6P2V 0x30 +#define VBUS_OVV_SELECT_6P3V 0x38 + +#define VBUS_AUTO_IN_CURR_LIM_ENA 0x04 + +/* Fuel Gauge constants */ +#define RESET_ACCU 0x02 +#define READ_REQ 0x01 +#define CC_DEEP_SLEEP_ENA 0x02 +#define CC_PWR_UP_ENA 0x01 +#define CC_SAMPLES_40 0x28 +#define RD_NCONV_ACCU_REQ 0x01 +#define CC_CALIB 0x08 +#define CC_INTAVGOFFSET_ENA 0x10 +#define CC_MUXOFFSET 0x80 +#define CC_INT_CAL_N_AVG_MASK 0x60 +#define CC_INT_CAL_SAMPLES_16 0x40 +#define CC_INT_CAL_SAMPLES_8 0x20 +#define CC_INT_CAL_SAMPLES_4 0x00 + +/* RTC constants */ +#define RTC_BUP_CH_ENA 0x10 + +/* BatCtrl Current Source Constants */ +#define BAT_CTRL_7U_ENA 0x01 +#define BAT_CTRL_20U_ENA 0x02 +#define BAT_CTRL_CMP_ENA 0x04 +#define FORCE_BAT_CTRL_CMP_HIGH 0x08 +#define BAT_CTRL_PULL_UP_ENA 0x10 + +/* Battery type */ +#define BATTERY_UNKNOWN 00 + +/** + * struct res_to_temp - defines one point in a temp to res curve. To + * be used in battery packs that combines the identification resistor with a + * NTC resistor. + * @temp: battery pack temperature in Celcius + * @resist: NTC resistor net total resistance + */ +struct res_to_temp { + int temp; + int resist; +}; + +/** + * struct batres_vs_temp - defines one point in a temp vs battery internal + * resistance curve. + * @temp: battery pack temperature in Celcius + * @resist: battery internal reistance in mOhm + */ +struct batres_vs_temp { + int temp; + int resist; +}; + +/* Forward declaration */ +struct ab8500_fg; + +/** + * struct ab8500_fg_parameters - Fuel gauge algorithm parameters, in seconds + * if not specified + * @recovery_sleep_timer: Time between measurements while recovering + * @recovery_total_time: Total recovery time + * @init_timer: Measurement interval during startup + * @init_discard_time: Time we discard voltage measurement at startup + * @init_total_time: Total init time during startup + * @high_curr_time: Time current has to be high to go to recovery + * @accu_charging: FG accumulation time while charging + * @accu_high_curr: FG accumulation time in high current mode + * @high_curr_threshold: High current threshold, in mA + * @lowbat_threshold: Low battery threshold, in mV + * @battok_falling_th_sel0 Threshold in mV for battOk signal sel0 + * Resolution in 50 mV step. + * @battok_raising_th_sel1 Threshold in mV for battOk signal sel1 + * Resolution in 50 mV step. + * @user_cap_limit Capacity reported from user must be within this + * limit to be considered as sane, in percentage + * points. + * @maint_thres This is the threshold where we stop reporting + * battery full while in maintenance, in per cent + */ +struct ab8500_fg_parameters { + int recovery_sleep_timer; + int recovery_total_time; + int init_timer; + int init_discard_time; + int init_total_time; + int high_curr_time; + int accu_charging; + int accu_high_curr; + int high_curr_threshold; + int lowbat_threshold; + int battok_falling_th_sel0; + int battok_raising_th_sel1; + int user_cap_limit; + int maint_thres; +}; + +/** + * struct ab8500_charger_maximization - struct used by the board config. + * @use_maxi: Enable maximization for this battery type + * @maxi_chg_curr: Maximum charger current allowed + * @maxi_wait_cycles: cycles to wait before setting charger current + * @charger_curr_step delta between two charger current settings (mA) + */ +struct ab8500_maxim_parameters { + bool ena_maxi; + int chg_curr; + int wait_cycles; + int charger_curr_step; +}; + +/** + * struct ab8500_bm_capacity_levels - ab8500 capacity level data + * @critical: critical capacity level in percent + * @low: low capacity level in percent + * @normal: normal capacity level in percent + * @high: high capacity level in percent + * @full: full capacity level in percent + */ +struct ab8500_bm_capacity_levels { + int critical; + int low; + int normal; + int high; + int full; +}; + +/** + * struct ab8500_bm_charger_parameters - Charger specific parameters + * @usb_volt_max: maximum allowed USB charger voltage in mV + * @usb_curr_max: maximum allowed USB charger current in mA + * @ac_volt_max: maximum allowed AC charger voltage in mV + * @ac_curr_max: maximum allowed AC charger current in mA + */ +struct ab8500_bm_charger_parameters { + int usb_volt_max; + int usb_curr_max; + int ac_volt_max; + int ac_curr_max; +}; + +/** + * struct ab8500_bm_data - ab8500 battery management data + * @temp_under under this temp, charging is stopped + * @temp_low between this temp and temp_under charging is reduced + * @temp_high between this temp and temp_over charging is reduced + * @temp_over over this temp, charging is stopped + * @temp_interval_chg temperature measurement interval in s when charging + * @temp_interval_nochg temperature measurement interval in s when not charging + * @main_safety_tmr_h safety timer for main charger + * @usb_safety_tmr_h safety timer for usb charger + * @bkup_bat_v voltage which we charge the backup battery with + * @bkup_bat_i current which we charge the backup battery with + * @no_maintenance indicates that maintenance charging is disabled + * @adc_therm placement of thermistor, batctrl or battemp adc + * @chg_unknown_bat flag to enable charging of unknown batteries + * @enable_overshoot flag to enable VBAT overshoot control + * @fg_res resistance of FG resistor in 0.1mOhm + * @n_btypes number of elements in array bat_type + * @batt_id index of the identified battery in array bat_type + * @interval_charging charge alg cycle period time when charging (sec) + * @interval_not_charging charge alg cycle period time when not charging (sec) + * @temp_hysteresis temperature hysteresis + * @gnd_lift_resistance Battery ground to phone ground resistance (mOhm) + * @maxi: maximization parameters + * @cap_levels capacity in percent for the different capacity levels + * @bat_type table of supported battery types + * @chg_params charger parameters + * @fg_params fuel gauge parameters + */ +struct ab8500_bm_data { + int temp_under; + int temp_low; + int temp_high; + int temp_over; + int temp_interval_chg; + int temp_interval_nochg; + int main_safety_tmr_h; + int usb_safety_tmr_h; + int bkup_bat_v; + int bkup_bat_i; + bool no_maintenance; + bool chg_unknown_bat; + bool enable_overshoot; + enum abx500_adc_therm adc_therm; + int fg_res; + int n_btypes; + int batt_id; + int interval_charging; + int interval_not_charging; + int temp_hysteresis; + int gnd_lift_resistance; + const struct ab8500_maxim_parameters *maxi; + const struct ab8500_bm_capacity_levels *cap_levels; + const struct ab8500_bm_charger_parameters *chg_params; + const struct ab8500_fg_parameters *fg_params; +}; + +struct ab8500_charger_platform_data { + char **supplied_to; + size_t num_supplicants; + bool autopower_cfg; +}; + +struct ab8500_btemp_platform_data { + char **supplied_to; + size_t num_supplicants; +}; + +struct ab8500_fg_platform_data { + char **supplied_to; + size_t num_supplicants; +}; + +struct ab8500_chargalg_platform_data { + char **supplied_to; + size_t num_supplicants; +}; +struct ab8500_btemp; +struct ab8500_gpadc; +struct ab8500_fg; +#ifdef CONFIG_AB8500_BM +void ab8500_fg_reinit(void); +void ab8500_charger_usb_state_changed(u8 bm_usb_state, u16 mA); +struct ab8500_btemp *ab8500_btemp_get(void); +int ab8500_btemp_get_batctrl_temp(struct ab8500_btemp *btemp); +struct ab8500_fg *ab8500_fg_get(void); +int ab8500_fg_inst_curr_blocking(struct ab8500_fg *dev); +int ab8500_fg_inst_curr_start(struct ab8500_fg *di); +int ab8500_fg_inst_curr_finalize(struct ab8500_fg *di, int *res); +int ab8500_fg_inst_curr_done(struct ab8500_fg *di); + +#else +int ab8500_fg_inst_curr_done(struct ab8500_fg *di) +{ +} +static void ab8500_fg_reinit(void) +{ +} +static void ab8500_charger_usb_state_changed(u8 bm_usb_state, u16 mA) +{ +} +static struct ab8500_btemp *ab8500_btemp_get(void) +{ + return NULL; +} +static int ab8500_btemp_get_batctrl_temp(struct ab8500_btemp *btemp) +{ + return 0; +} +struct ab8500_fg *ab8500_fg_get(void) +{ + return NULL; +} +static int ab8500_fg_inst_curr_blocking(struct ab8500_fg *dev) +{ + return -ENODEV; +} + +static inline int ab8500_fg_inst_curr_start(struct ab8500_fg *di) +{ + return -ENODEV; +} + +static inline int ab8500_fg_inst_curr_finalize(struct ab8500_fg *di, int *res) +{ + return -ENODEV; +} + +#endif +#endif /* _AB8500_BM_H */ diff --git a/include/linux/mfd/abx500/ab8500-gpio.h b/include/linux/mfd/abx500/ab8500-gpio.h index 488a8c920a2..2387c207ea8 100644 --- a/include/linux/mfd/abx500/ab8500-gpio.h +++ b/include/linux/mfd/abx500/ab8500-gpio.h @@ -10,12 +10,14 @@ /* * Platform data to register a block: only the initial gpio/irq number. + * Array sizes are large enough to contain all AB8500 and AB9540 GPIO + * registers. */ struct ab8500_gpio_platform_data { int gpio_base; u32 irq_base; - u8 config_reg[7]; + u8 config_reg[8]; }; #endif /* _AB8500_GPIO_H */ diff --git a/include/linux/mfd/abx500/ab8500-sysctrl.h b/include/linux/mfd/abx500/ab8500-sysctrl.h index 10da0291f8f..10eb50973c3 100644 --- a/include/linux/mfd/abx500/ab8500-sysctrl.h +++ b/include/linux/mfd/abx500/ab8500-sysctrl.h @@ -71,6 +71,13 @@ static inline int ab8500_sysctrl_clear(u16 reg, u8 bits) #define AB8500_SWATCTRL 0x230 #define AB8500_HIQCLKCTRL 0x232 #define AB8500_VSIMSYSCLKCTRL 0x233 +#define AB9540_SYSCLK12BUFCTRL 0x234 +#define AB9540_SYSCLK12CONFCTRL 0x235 +#define AB9540_SYSCLK12BUFCTRL2 0x236 +#define AB9540_SYSCLK12BUF1VALID 0x237 +#define AB9540_SYSCLK12BUF2VALID 0x238 +#define AB9540_SYSCLK12BUF3VALID 0x239 +#define AB9540_SYSCLK12BUF4VALID 0x23A /* Bits */ #define AB8500_TURNONSTATUS_PORNVBAT BIT(0) @@ -251,4 +258,40 @@ static inline int ab8500_sysctrl_clear(u16 reg, u8 bits) #define AB8500_VSIMSYSCLKCTRL_VSIMSYSCLKREQ7VALID BIT(6) #define AB8500_VSIMSYSCLKCTRL_VSIMSYSCLKREQ8VALID BIT(7) +#define AB9540_SYSCLK12BUFCTRL_SYSCLK12BUF1ENA BIT(0) +#define AB9540_SYSCLK12BUFCTRL_SYSCLK12BUF2ENA BIT(1) +#define AB9540_SYSCLK12BUFCTRL_SYSCLK12BUF3ENA BIT(2) +#define AB9540_SYSCLK12BUFCTRL_SYSCLK12BUF4ENA BIT(3) +#define AB9540_SYSCLK12BUFCTRL_SYSCLK12BUFENA_MASK 0x0F +#define AB9540_SYSCLK12BUFCTRL_SYSCLK12BUF1STRE BIT(4) +#define AB9540_SYSCLK12BUFCTRL_SYSCLK12BUF2STRE BIT(5) +#define AB9540_SYSCLK12BUFCTRL_SYSCLK12BUF3STRE BIT(6) +#define AB9540_SYSCLK12BUFCTRL_SYSCLK12BUF4STRE BIT(7) +#define AB9540_SYSCLK12BUFCTRL_SYSCLK12BUFSTRE_MASK 0xF0 + +#define AB9540_SYSCLK12CONFCTRL_PLL26TO38ENA BIT(0) +#define AB9540_SYSCLK12CONFCTRL_SYSCLK12USBMUXSEL BIT(1) +#define AB9540_SYSCLK12CONFCTRL_INT384MHZMUXSEL_MASK 0x0C +#define AB9540_SYSCLK12CONFCTRL_INT384MHZMUXSEL_SHIFT 2 +#define AB9540_SYSCLK12CONFCTRL_SYSCLK12BUFMUX BIT(4) +#define AB9540_SYSCLK12CONFCTRL_SYSCLK12PLLMUX BIT(5) +#define AB9540_SYSCLK12CONFCTRL_SYSCLK2MUXVALID BIT(6) + +#define AB9540_SYSCLK12BUFCTRL2_SYSCLK12BUF1PDENA BIT(0) +#define AB9540_SYSCLK12BUFCTRL2_SYSCLK12BUF2PDENA BIT(1) +#define AB9540_SYSCLK12BUFCTRL2_SYSCLK12BUF3PDENA BIT(2) +#define AB9540_SYSCLK12BUFCTRL2_SYSCLK12BUF4PDENA BIT(3) + +#define AB9540_SYSCLK12BUF1VALID_SYSCLK12BUF1VALID_MASK 0xFF +#define AB9540_SYSCLK12BUF1VALID_SYSCLK12BUF1VALID_SHIFT 0 + +#define AB9540_SYSCLK12BUF2VALID_SYSCLK12BUF2VALID_MASK 0xFF +#define AB9540_SYSCLK12BUF2VALID_SYSCLK12BUF2VALID_SHIFT 0 + +#define AB9540_SYSCLK12BUF3VALID_SYSCLK12BUF3VALID_MASK 0xFF +#define AB9540_SYSCLK12BUF3VALID_SYSCLK12BUF3VALID_SHIFT 0 + +#define AB9540_SYSCLK12BUF4VALID_SYSCLK12BUF4VALID_MASK 0xFF +#define AB9540_SYSCLK12BUF4VALID_SYSCLK12BUF4VALID_SHIFT 0 + #endif /* __AB8500_SYSCTRL_H */ diff --git a/include/linux/mfd/abx500/ab8500.h b/include/linux/mfd/abx500/ab8500.h index dca94396190..fccc3002f27 100644 --- a/include/linux/mfd/abx500/ab8500.h +++ b/include/linux/mfd/abx500/ab8500.h @@ -12,6 +12,29 @@ struct device; /* + * AB IC versions + * + * AB8500_VERSION_AB8500 should be 0xFF but will never be read as need a + * non-supported multi-byte I2C access via PRCMU. Set to 0x00 to ease the + * print of version string. + */ +enum ab8500_version { + AB8500_VERSION_AB8500 = 0x0, + AB8500_VERSION_AB8505 = 0x1, + AB8500_VERSION_AB9540 = 0x2, + AB8500_VERSION_AB8540 = 0x3, + AB8500_VERSION_UNDEFINED, +}; + +/* AB8500 CIDs*/ +#define AB8500_CUTEARLY 0x00 +#define AB8500_CUT1P0 0x10 +#define AB8500_CUT1P1 0x11 +#define AB8500_CUT2P0 0x20 +#define AB8500_CUT3P0 0x30 +#define AB8500_CUT3P3 0x33 + +/* * AB8500 bank addresses */ #define AB8500_SYS_CTRL1_BLOCK 0x1 @@ -37,30 +60,34 @@ struct device; /* * Interrupts + * Values used to index into array ab8500_irq_regoffset[] defined in + * drivers/mdf/ab8500-core.c */ - -#define AB8500_INT_MAIN_EXT_CH_NOT_OK 0 -#define AB8500_INT_UN_PLUG_TV_DET 1 -#define AB8500_INT_PLUG_TV_DET 2 +/* Definitions for AB8500 and AB9540 */ +/* ab8500_irq_regoffset[0] -> IT[Source|Latch|Mask]1 */ +#define AB8500_INT_MAIN_EXT_CH_NOT_OK 0 /* not 8505/9540 */ +#define AB8500_INT_UN_PLUG_TV_DET 1 /* not 8505/9540 */ +#define AB8500_INT_PLUG_TV_DET 2 /* not 8505/9540 */ #define AB8500_INT_TEMP_WARM 3 #define AB8500_INT_PON_KEY2DB_F 4 #define AB8500_INT_PON_KEY2DB_R 5 #define AB8500_INT_PON_KEY1DB_F 6 #define AB8500_INT_PON_KEY1DB_R 7 +/* ab8500_irq_regoffset[1] -> IT[Source|Latch|Mask]2 */ #define AB8500_INT_BATT_OVV 8 -#define AB8500_INT_MAIN_CH_UNPLUG_DET 10 -#define AB8500_INT_MAIN_CH_PLUG_DET 11 -#define AB8500_INT_USB_ID_DET_F 12 -#define AB8500_INT_USB_ID_DET_R 13 +#define AB8500_INT_MAIN_CH_UNPLUG_DET 10 /* not 8505 */ +#define AB8500_INT_MAIN_CH_PLUG_DET 11 /* not 8505 */ #define AB8500_INT_VBUS_DET_F 14 #define AB8500_INT_VBUS_DET_R 15 +/* ab8500_irq_regoffset[2] -> IT[Source|Latch|Mask]3 */ #define AB8500_INT_VBUS_CH_DROP_END 16 #define AB8500_INT_RTC_60S 17 #define AB8500_INT_RTC_ALARM 18 #define AB8500_INT_BAT_CTRL_INDB 20 #define AB8500_INT_CH_WD_EXP 21 #define AB8500_INT_VBUS_OVV 22 -#define AB8500_INT_MAIN_CH_DROP_END 23 +#define AB8500_INT_MAIN_CH_DROP_END 23 /* not 8505/9540 */ +/* ab8500_irq_regoffset[3] -> IT[Source|Latch|Mask]4 */ #define AB8500_INT_CCN_CONV_ACC 24 #define AB8500_INT_INT_AUD 25 #define AB8500_INT_CCEOC 26 @@ -69,7 +96,8 @@ struct device; #define AB8500_INT_LOW_BAT_R 29 #define AB8500_INT_BUP_CHG_NOT_OK 30 #define AB8500_INT_BUP_CHG_OK 31 -#define AB8500_INT_GP_HW_ADC_CONV_END 32 +/* ab8500_irq_regoffset[4] -> IT[Source|Latch|Mask]5 */ +#define AB8500_INT_GP_HW_ADC_CONV_END 32 /* not 8505 */ #define AB8500_INT_ACC_DETECT_1DB_F 33 #define AB8500_INT_ACC_DETECT_1DB_R 34 #define AB8500_INT_ACC_DETECT_22DB_F 35 @@ -77,38 +105,43 @@ struct device; #define AB8500_INT_ACC_DETECT_21DB_F 37 #define AB8500_INT_ACC_DETECT_21DB_R 38 #define AB8500_INT_GP_SW_ADC_CONV_END 39 -#define AB8500_INT_GPIO6R 40 -#define AB8500_INT_GPIO7R 41 -#define AB8500_INT_GPIO8R 42 -#define AB8500_INT_GPIO9R 43 +/* ab8500_irq_regoffset[5] -> IT[Source|Latch|Mask]7 */ +#define AB8500_INT_GPIO6R 40 /* not 8505/9540 */ +#define AB8500_INT_GPIO7R 41 /* not 8505/9540 */ +#define AB8500_INT_GPIO8R 42 /* not 8505/9540 */ +#define AB8500_INT_GPIO9R 43 /* not 8505/9540 */ #define AB8500_INT_GPIO10R 44 #define AB8500_INT_GPIO11R 45 -#define AB8500_INT_GPIO12R 46 +#define AB8500_INT_GPIO12R 46 /* not 8505 */ #define AB8500_INT_GPIO13R 47 -#define AB8500_INT_GPIO24R 48 -#define AB8500_INT_GPIO25R 49 -#define AB8500_INT_GPIO36R 50 -#define AB8500_INT_GPIO37R 51 -#define AB8500_INT_GPIO38R 52 -#define AB8500_INT_GPIO39R 53 +/* ab8500_irq_regoffset[6] -> IT[Source|Latch|Mask]8 */ +#define AB8500_INT_GPIO24R 48 /* not 8505 */ +#define AB8500_INT_GPIO25R 49 /* not 8505 */ +#define AB8500_INT_GPIO36R 50 /* not 8505/9540 */ +#define AB8500_INT_GPIO37R 51 /* not 8505/9540 */ +#define AB8500_INT_GPIO38R 52 /* not 8505/9540 */ +#define AB8500_INT_GPIO39R 53 /* not 8505/9540 */ #define AB8500_INT_GPIO40R 54 #define AB8500_INT_GPIO41R 55 -#define AB8500_INT_GPIO6F 56 -#define AB8500_INT_GPIO7F 57 -#define AB8500_INT_GPIO8F 58 -#define AB8500_INT_GPIO9F 59 +/* ab8500_irq_regoffset[7] -> IT[Source|Latch|Mask]9 */ +#define AB8500_INT_GPIO6F 56 /* not 8505/9540 */ +#define AB8500_INT_GPIO7F 57 /* not 8505/9540 */ +#define AB8500_INT_GPIO8F 58 /* not 8505/9540 */ +#define AB8500_INT_GPIO9F 59 /* not 8505/9540 */ #define AB8500_INT_GPIO10F 60 #define AB8500_INT_GPIO11F 61 -#define AB8500_INT_GPIO12F 62 +#define AB8500_INT_GPIO12F 62 /* not 8505 */ #define AB8500_INT_GPIO13F 63 -#define AB8500_INT_GPIO24F 64 -#define AB8500_INT_GPIO25F 65 -#define AB8500_INT_GPIO36F 66 -#define AB8500_INT_GPIO37F 67 -#define AB8500_INT_GPIO38F 68 -#define AB8500_INT_GPIO39F 69 +/* ab8500_irq_regoffset[8] -> IT[Source|Latch|Mask]10 */ +#define AB8500_INT_GPIO24F 64 /* not 8505 */ +#define AB8500_INT_GPIO25F 65 /* not 8505 */ +#define AB8500_INT_GPIO36F 66 /* not 8505/9540 */ +#define AB8500_INT_GPIO37F 67 /* not 8505/9540 */ +#define AB8500_INT_GPIO38F 68 /* not 8505/9540 */ +#define AB8500_INT_GPIO39F 69 /* not 8505/9540 */ #define AB8500_INT_GPIO40F 70 #define AB8500_INT_GPIO41F 71 +/* ab8500_irq_regoffset[9] -> IT[Source|Latch|Mask]12 */ #define AB8500_INT_ADP_SOURCE_ERROR 72 #define AB8500_INT_ADP_SINK_ERROR 73 #define AB8500_INT_ADP_PROBE_PLUG 74 @@ -116,30 +149,67 @@ struct device; #define AB8500_INT_ADP_SENSE_OFF 76 #define AB8500_INT_USB_PHY_POWER_ERR 78 #define AB8500_INT_USB_LINK_STATUS 79 +/* ab8500_irq_regoffset[10] -> IT[Source|Latch|Mask]19 */ #define AB8500_INT_BTEMP_LOW 80 #define AB8500_INT_BTEMP_LOW_MEDIUM 81 #define AB8500_INT_BTEMP_MEDIUM_HIGH 82 #define AB8500_INT_BTEMP_HIGH 83 -#define AB8500_INT_USB_CHARGER_NOT_OK 89 +/* ab8500_irq_regoffset[11] -> IT[Source|Latch|Mask]20 */ +#define AB8500_INT_SRP_DETECT 88 +#define AB8500_INT_USB_CHARGER_NOT_OKR 89 #define AB8500_INT_ID_WAKEUP_R 90 #define AB8500_INT_ID_DET_R1R 92 #define AB8500_INT_ID_DET_R2R 93 #define AB8500_INT_ID_DET_R3R 94 #define AB8500_INT_ID_DET_R4R 95 +/* ab8500_irq_regoffset[12] -> IT[Source|Latch|Mask]21 */ #define AB8500_INT_ID_WAKEUP_F 96 #define AB8500_INT_ID_DET_R1F 98 #define AB8500_INT_ID_DET_R2F 99 #define AB8500_INT_ID_DET_R3F 100 #define AB8500_INT_ID_DET_R4F 101 -#define AB8500_INT_USB_CHG_DET_DONE 102 +#define AB8500_INT_CHAUTORESTARTAFTSEC 102 +#define AB8500_INT_CHSTOPBYSEC 103 +/* ab8500_irq_regoffset[13] -> IT[Source|Latch|Mask]22 */ #define AB8500_INT_USB_CH_TH_PROT_F 104 #define AB8500_INT_USB_CH_TH_PROT_R 105 -#define AB8500_INT_MAIN_CH_TH_PROT_F 106 -#define AB8500_INT_MAIN_CH_TH_PROT_R 107 -#define AB8500_INT_USB_CHARGER_NOT_OKF 111 +#define AB8500_INT_MAIN_CH_TH_PROT_F 106 /* not 8505/9540 */ +#define AB8500_INT_MAIN_CH_TH_PROT_R 107 /* not 8505/9540 */ +#define AB8500_INT_CHCURLIMNOHSCHIRP 109 +#define AB8500_INT_CHCURLIMHSCHIRP 110 +#define AB8500_INT_XTAL32K_KO 111 + +/* Definitions for AB9540 */ +/* ab8500_irq_regoffset[14] -> IT[Source|Latch|Mask]13 */ +#define AB9540_INT_GPIO50R 113 +#define AB9540_INT_GPIO51R 114 /* not 8505 */ +#define AB9540_INT_GPIO52R 115 +#define AB9540_INT_GPIO53R 116 +#define AB9540_INT_GPIO54R 117 /* not 8505 */ +#define AB9540_INT_IEXT_CH_RF_BFN_R 118 +#define AB9540_INT_IEXT_CH_RF_BFN_F 119 +/* ab8500_irq_regoffset[15] -> IT[Source|Latch|Mask]14 */ +#define AB9540_INT_GPIO50F 121 +#define AB9540_INT_GPIO51F 122 /* not 8505 */ +#define AB9540_INT_GPIO52F 123 +#define AB9540_INT_GPIO53F 124 +#define AB9540_INT_GPIO54F 125 /* not 8505 */ +/* + * AB8500_AB9540_NR_IRQS is used when configuring the IRQ numbers for the + * entire platform. This is a "compile time" constant so this must be set to + * the largest possible value that may be encountered with different AB SOCs. + * Of the currently supported AB devices, AB8500 and AB9540, it is the AB9540 + * which is larger. + */ #define AB8500_NR_IRQS 112 +#define AB8505_NR_IRQS 128 +#define AB9540_NR_IRQS 128 +/* This is set to the roof of any AB8500 chip variant IRQ counts */ +#define AB8500_MAX_NR_IRQS AB9540_NR_IRQS + #define AB8500_NUM_IRQ_REGS 14 +#define AB9540_NUM_IRQ_REGS 17 /** * struct ab8500 - ab8500 internal structure @@ -147,13 +217,18 @@ struct device; * @lock: read/write operations lock * @irq_lock: genirq bus lock * @irq: irq line + * @version: chip version id (e.g. ab8500 or ab9540) * @chip_id: chip revision id * @write: register write + * @write_masked: masked register write * @read: register read * @rx_buf: rx buf for SPI * @tx_buf: tx buf for SPI * @mask: cache of IRQ regs for bus lock * @oldmask: cache of previous IRQ regs for bus lock + * @mask_size: Actual number of valid entries in mask[], oldmask[] and + * irq_reg_offset + * @irq_reg_offset: Array of offsets into IRQ registers */ struct ab8500 { struct device *dev; @@ -162,16 +237,20 @@ struct ab8500 { int irq_base; int irq; + enum ab8500_version version; u8 chip_id; - int (*write) (struct ab8500 *a8500, u16 addr, u8 data); - int (*read) (struct ab8500 *a8500, u16 addr); + int (*write)(struct ab8500 *ab8500, u16 addr, u8 data); + int (*write_masked)(struct ab8500 *ab8500, u16 addr, u8 mask, u8 data); + int (*read)(struct ab8500 *ab8500, u16 addr); unsigned long tx_buf[4]; unsigned long rx_buf[4]; - u8 mask[AB8500_NUM_IRQ_REGS]; - u8 oldmask[AB8500_NUM_IRQ_REGS]; + u8 *mask; + u8 *oldmask; + int mask_size; + const int *irq_reg_offset; }; struct regulator_reg_init; @@ -197,7 +276,52 @@ struct ab8500_platform_data { struct ab8500_gpio_platform_data *gpio; }; -extern int __devinit ab8500_init(struct ab8500 *ab8500); +extern int __devinit ab8500_init(struct ab8500 *ab8500, + enum ab8500_version version); extern int __devexit ab8500_exit(struct ab8500 *ab8500); +static inline int is_ab8500(struct ab8500 *ab) +{ + return ab->version == AB8500_VERSION_AB8500; +} + +static inline int is_ab8505(struct ab8500 *ab) +{ + return ab->version == AB8500_VERSION_AB8505; +} + +static inline int is_ab9540(struct ab8500 *ab) +{ + return ab->version == AB8500_VERSION_AB9540; +} + +static inline int is_ab8540(struct ab8500 *ab) +{ + return ab->version == AB8500_VERSION_AB8540; +} + +/* exclude also ab8505, ab9540... */ +static inline int is_ab8500_1p0_or_earlier(struct ab8500 *ab) +{ + return (is_ab8500(ab) && (ab->chip_id <= AB8500_CUT1P0)); +} + +/* exclude also ab8505, ab9540... */ +static inline int is_ab8500_1p1_or_earlier(struct ab8500 *ab) +{ + return (is_ab8500(ab) && (ab->chip_id <= AB8500_CUT1P1)); +} + +/* exclude also ab8505, ab9540... */ +static inline int is_ab8500_2p0_or_earlier(struct ab8500 *ab) +{ + return (is_ab8500(ab) && (ab->chip_id <= AB8500_CUT2P0)); +} + +/* exclude also ab8505, ab9540... */ +static inline int is_ab8500_2p0(struct ab8500 *ab) +{ + return (is_ab8500(ab) && (ab->chip_id == AB8500_CUT2P0)); +} + #endif /* MFD_AB8500_H */ diff --git a/include/linux/mfd/abx500/ux500_chargalg.h b/include/linux/mfd/abx500/ux500_chargalg.h new file mode 100644 index 00000000000..9b07725750c --- /dev/null +++ b/include/linux/mfd/abx500/ux500_chargalg.h @@ -0,0 +1,38 @@ +/* + * Copyright (C) ST-Ericsson SA 2012 + * Author: Johan Gardsmark <johan.gardsmark@stericsson.com> for ST-Ericsson. + * License terms: GNU General Public License (GPL), version 2 + */ + +#ifndef _UX500_CHARGALG_H +#define _UX500_CHARGALG_H + +#include <linux/power_supply.h> + +#define psy_to_ux500_charger(x) container_of((x), \ + struct ux500_charger, psy) + +/* Forward declaration */ +struct ux500_charger; + +struct ux500_charger_ops { + int (*enable) (struct ux500_charger *, int, int, int); + int (*kick_wd) (struct ux500_charger *); + int (*update_curr) (struct ux500_charger *, int); +}; + +/** + * struct ux500_charger - power supply ux500 charger sub class + * @psy power supply base class + * @ops ux500 charger operations + * @max_out_volt maximum output charger voltage in mV + * @max_out_curr maximum output charger current in mA + */ +struct ux500_charger { + struct power_supply psy; + struct ux500_charger_ops ops; + int max_out_volt; + int max_out_curr; +}; + +#endif diff --git a/include/linux/mfd/anatop.h b/include/linux/mfd/anatop.h new file mode 100644 index 00000000000..22c1007d3ec --- /dev/null +++ b/include/linux/mfd/anatop.h @@ -0,0 +1,40 @@ +/* + * anatop.h - Anatop MFD driver + * + * Copyright (C) 2012 Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org> + * Copyright (C) 2012 Linaro + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __LINUX_MFD_ANATOP_H +#define __LINUX_MFD_ANATOP_H + +#include <linux/spinlock.h> + +/** + * anatop - MFD data + * @ioreg: ioremap register + * @reglock: spinlock for register read/write + */ +struct anatop { + void *ioreg; + spinlock_t reglock; +}; + +extern u32 anatop_get_bits(struct anatop *, u32, int, int); +extern void anatop_set_bits(struct anatop *, u32, int, int, u32); + +#endif /* __LINUX_MFD_ANATOP_H */ diff --git a/include/linux/mfd/da9052/da9052.h b/include/linux/mfd/da9052/da9052.h index 5702d1be13b..7ffbd6e9e7f 100644 --- a/include/linux/mfd/da9052/da9052.h +++ b/include/linux/mfd/da9052/da9052.h @@ -76,8 +76,6 @@ enum da9052_chip_id { struct da9052_pdata; struct da9052 { - struct mutex io_lock; - struct device *dev; struct regmap *regmap; diff --git a/include/linux/mfd/db8500-prcmu.h b/include/linux/mfd/db8500-prcmu.h index 60d27f7bfc1..b3a43b1263f 100644 --- a/include/linux/mfd/db8500-prcmu.h +++ b/include/linux/mfd/db8500-prcmu.h @@ -11,6 +11,24 @@ #define __MFD_DB8500_PRCMU_H #include <linux/interrupt.h> +#include <linux/bitops.h> + +/* + * Registers + */ +#define DB8500_PRCM_GPIOCR 0x138 +#define DB8500_PRCM_GPIOCR_DBG_UARTMOD_CMD0 BIT(0) +#define DB8500_PRCM_GPIOCR_DBG_STM_APE_CMD BIT(9) +#define DB8500_PRCM_GPIOCR_DBG_STM_MOD_CMD1 BIT(11) +#define DB8500_PRCM_GPIOCR_SPI2_SELECT BIT(23) + +#define DB8500_PRCM_LINE_VALUE 0x170 +#define DB8500_PRCM_LINE_VALUE_HSI_CAWAKE0 BIT(3) + +#define DB8500_PRCM_DSI_SW_RESET 0x324 +#define DB8500_PRCM_DSI_SW_RESET_DSI0_SW_RESETN BIT(0) +#define DB8500_PRCM_DSI_SW_RESET_DSI1_SW_RESETN BIT(1) +#define DB8500_PRCM_DSI_SW_RESET_DSI2_SW_RESETN BIT(2) /* This portion previously known as <mach/prcmu-fw-defs_v1.h> */ @@ -421,40 +439,22 @@ enum auto_enable { /* End of file previously known as prcmu-fw-defs_v1.h */ /** - * enum hw_acc_dev - enum for hw accelerators - * @HW_ACC_SVAMMDSP: for SVAMMDSP - * @HW_ACC_SVAPIPE: for SVAPIPE - * @HW_ACC_SIAMMDSP: for SIAMMDSP - * @HW_ACC_SIAPIPE: for SIAPIPE - * @HW_ACC_SGA: for SGA - * @HW_ACC_B2R2: for B2R2 - * @HW_ACC_MCDE: for MCDE - * @HW_ACC_ESRAM1: for ESRAM1 - * @HW_ACC_ESRAM2: for ESRAM2 - * @HW_ACC_ESRAM3: for ESRAM3 - * @HW_ACC_ESRAM4: for ESRAM4 - * @NUM_HW_ACC: number of hardware accelerators - * - * Different hw accelerators which can be turned ON/ - * OFF or put into retention (MMDSPs and ESRAMs). - * Used with EPOD API. + * enum prcmu_power_status - results from set_power_state + * @PRCMU_SLEEP_OK: Sleep went ok + * @PRCMU_DEEP_SLEEP_OK: DeepSleep went ok + * @PRCMU_IDLE_OK: Idle went ok + * @PRCMU_DEEPIDLE_OK: DeepIdle went ok + * @PRCMU_PRCMU2ARMPENDINGIT_ER: Pending interrupt detected + * @PRCMU_ARMPENDINGIT_ER: Pending interrupt detected * - * NOTE! Deprecated, to be removed when all users switched over to use the - * regulator API. */ -enum hw_acc_dev { - HW_ACC_SVAMMDSP, - HW_ACC_SVAPIPE, - HW_ACC_SIAMMDSP, - HW_ACC_SIAPIPE, - HW_ACC_SGA, - HW_ACC_B2R2, - HW_ACC_MCDE, - HW_ACC_ESRAM1, - HW_ACC_ESRAM2, - HW_ACC_ESRAM3, - HW_ACC_ESRAM4, - NUM_HW_ACC +enum prcmu_power_status { + PRCMU_SLEEP_OK = 0xf3, + PRCMU_DEEP_SLEEP_OK = 0xf6, + PRCMU_IDLE_OK = 0xf0, + PRCMU_DEEPIDLE_OK = 0xe3, + PRCMU_PRCMU2ARMPENDINGIT_ER = 0x91, + PRCMU_ARMPENDINGIT_ER = 0x93, }; /* @@ -493,6 +493,20 @@ struct prcmu_auto_pm_config { u8 sva_policy; }; +#define PRCMU_FW_PROJECT_U8500 2 +#define PRCMU_FW_PROJECT_U9500 4 +#define PRCMU_FW_PROJECT_U8500_C2 7 +#define PRCMU_FW_PROJECT_U9500_C2 11 +#define PRCMU_FW_PROJECT_U8520 13 +#define PRCMU_FW_PROJECT_U8420 14 + +struct prcmu_fw_version { + u8 project; + u8 api_version; + u8 func_version; + u8 errata; +}; + #ifdef CONFIG_MFD_DB8500_PRCMU void db8500_prcmu_early_init(void); @@ -500,42 +514,41 @@ int prcmu_set_rc_a2p(enum romcode_write); enum romcode_read prcmu_get_rc_p2a(void); enum ap_pwrst prcmu_get_xp70_current_state(void); bool prcmu_has_arm_maxopp(void); -bool prcmu_is_u8400(void); -int prcmu_set_ape_opp(u8 opp); -int prcmu_get_ape_opp(void); +struct prcmu_fw_version *prcmu_get_fw_version(void); int prcmu_request_ape_opp_100_voltage(bool enable); int prcmu_release_usb_wakeup_state(void); -int prcmu_set_ddr_opp(u8 opp); -int prcmu_get_ddr_opp(void); -/* NOTE! Use regulator framework instead */ -int prcmu_set_hwacc(u16 hw_acc_dev, u8 state); void prcmu_configure_auto_pm(struct prcmu_auto_pm_config *sleep, struct prcmu_auto_pm_config *idle); bool prcmu_is_auto_pm_enabled(void); int prcmu_config_clkout(u8 clkout, u8 source, u8 div); int prcmu_set_clock_divider(u8 clock, u8 divider); -int prcmu_config_hotdog(u8 threshold); -int prcmu_config_hotmon(u8 low, u8 high); -int prcmu_start_temp_sense(u16 cycles32k); -int prcmu_stop_temp_sense(void); +int db8500_prcmu_config_hotdog(u8 threshold); +int db8500_prcmu_config_hotmon(u8 low, u8 high); +int db8500_prcmu_start_temp_sense(u16 cycles32k); +int db8500_prcmu_stop_temp_sense(void); int prcmu_abb_read(u8 slave, u8 reg, u8 *value, u8 size); int prcmu_abb_write(u8 slave, u8 reg, u8 *value, u8 size); void prcmu_ac_wake_req(void); void prcmu_ac_sleep_req(void); -void prcmu_modem_reset(void); -void prcmu_enable_spi2(void); -void prcmu_disable_spi2(void); +void db8500_prcmu_modem_reset(void); -int prcmu_config_a9wdog(u8 num, bool sleep_auto_off); -int prcmu_enable_a9wdog(u8 id); -int prcmu_disable_a9wdog(u8 id); -int prcmu_kick_a9wdog(u8 id); -int prcmu_load_a9wdog(u8 id, u32 val); +int db8500_prcmu_config_a9wdog(u8 num, bool sleep_auto_off); +int db8500_prcmu_enable_a9wdog(u8 id); +int db8500_prcmu_disable_a9wdog(u8 id); +int db8500_prcmu_kick_a9wdog(u8 id); +int db8500_prcmu_load_a9wdog(u8 id, u32 val); void db8500_prcmu_system_reset(u16 reset_code); int db8500_prcmu_set_power_state(u8 state, bool keep_ulp_clk, bool keep_ap_pll); +u8 db8500_prcmu_get_power_state_result(void); +int db8500_prcmu_gic_decouple(void); +int db8500_prcmu_gic_recouple(void); +int db8500_prcmu_copy_gic_settings(void); +bool db8500_prcmu_gic_pending_irq(void); +bool db8500_prcmu_pending_irq(void); +bool db8500_prcmu_is_cpu_in_wfi(int cpu); void db8500_prcmu_enable_wakeups(u32 wakeups); int db8500_prcmu_set_epod(u16 epod_id, u8 epod_state); int db8500_prcmu_request_clock(u8 clock, bool enable); @@ -549,6 +562,14 @@ u16 db8500_prcmu_get_reset_code(void); bool db8500_prcmu_is_ac_wake_requested(void); int db8500_prcmu_set_arm_opp(u8 opp); int db8500_prcmu_get_arm_opp(void); +int db8500_prcmu_set_ape_opp(u8 opp); +int db8500_prcmu_get_ape_opp(void); +int db8500_prcmu_set_ddr_opp(u8 opp); +int db8500_prcmu_get_ddr_opp(void); + +u32 db8500_prcmu_read(unsigned int reg); +void db8500_prcmu_write(unsigned int reg, u32 value); +void db8500_prcmu_write_masked(unsigned int reg, u32 mask, u32 value); #else /* !CONFIG_MFD_DB8500_PRCMU */ @@ -574,17 +595,17 @@ static inline bool prcmu_has_arm_maxopp(void) return false; } -static inline bool prcmu_is_u8400(void) +static inline struct prcmu_fw_version *prcmu_get_fw_version(void) { - return false; + return NULL; } -static inline int prcmu_set_ape_opp(u8 opp) +static inline int db8500_prcmu_set_ape_opp(u8 opp) { return 0; } -static inline int prcmu_get_ape_opp(void) +static inline int db8500_prcmu_get_ape_opp(void) { return APE_100_OPP; } @@ -599,21 +620,16 @@ static inline int prcmu_release_usb_wakeup_state(void) return 0; } -static inline int prcmu_set_ddr_opp(u8 opp) +static inline int db8500_prcmu_set_ddr_opp(u8 opp) { return 0; } -static inline int prcmu_get_ddr_opp(void) +static inline int db8500_prcmu_get_ddr_opp(void) { return DDR_100_OPP; } -static inline int prcmu_set_hwacc(u16 hw_acc_dev, u8 state) -{ - return 0; -} - static inline void prcmu_configure_auto_pm(struct prcmu_auto_pm_config *sleep, struct prcmu_auto_pm_config *idle) { @@ -634,22 +650,22 @@ static inline int prcmu_set_clock_divider(u8 clock, u8 divider) return 0; } -static inline int prcmu_config_hotdog(u8 threshold) +static inline int db8500_prcmu_config_hotdog(u8 threshold) { return 0; } -static inline int prcmu_config_hotmon(u8 low, u8 high) +static inline int db8500_prcmu_config_hotmon(u8 low, u8 high) { return 0; } -static inline int prcmu_start_temp_sense(u16 cycles32k) +static inline int db8500_prcmu_start_temp_sense(u16 cycles32k) { return 0; } -static inline int prcmu_stop_temp_sense(void) +static inline int db8500_prcmu_stop_temp_sense(void) { return 0; } @@ -668,22 +684,17 @@ static inline void prcmu_ac_wake_req(void) {} static inline void prcmu_ac_sleep_req(void) {} -static inline void prcmu_modem_reset(void) {} +static inline void db8500_prcmu_modem_reset(void) {} -static inline int prcmu_enable_spi2(void) -{ - return 0; -} +static inline void db8500_prcmu_system_reset(u16 reset_code) {} -static inline int prcmu_disable_spi2(void) +static inline int db8500_prcmu_set_power_state(u8 state, bool keep_ulp_clk, + bool keep_ap_pll) { return 0; } -static inline void db8500_prcmu_system_reset(u16 reset_code) {} - -static inline int db8500_prcmu_set_power_state(u8 state, bool keep_ulp_clk, - bool keep_ap_pll) +static inline u8 db8500_prcmu_get_power_state_result(void) { return 0; } @@ -729,27 +740,27 @@ static inline u16 db8500_prcmu_get_reset_code(void) return 0; } -static inline int prcmu_config_a9wdog(u8 num, bool sleep_auto_off) +static inline int db8500_prcmu_config_a9wdog(u8 num, bool sleep_auto_off) { return 0; } -static inline int prcmu_enable_a9wdog(u8 id) +static inline int db8500_prcmu_enable_a9wdog(u8 id) { return 0; } -static inline int prcmu_disable_a9wdog(u8 id) +static inline int db8500_prcmu_disable_a9wdog(u8 id) { return 0; } -static inline int prcmu_kick_a9wdog(u8 id) +static inline int db8500_prcmu_kick_a9wdog(u8 id) { return 0; } -static inline int prcmu_load_a9wdog(u8 id, u32 val) +static inline int db8500_prcmu_load_a9wdog(u8 id, u32 val) { return 0; } @@ -769,6 +780,16 @@ static inline int db8500_prcmu_get_arm_opp(void) return 0; } +static inline u32 db8500_prcmu_read(unsigned int reg) +{ + return 0; +} + +static inline void db8500_prcmu_write(unsigned int reg, u32 value) {} + +static inline void db8500_prcmu_write_masked(unsigned int reg, u32 mask, + u32 value) {} + #endif /* !CONFIG_MFD_DB8500_PRCMU */ #endif /* __MFD_DB8500_PRCMU_H */ diff --git a/include/linux/mfd/dbx500-prcmu.h b/include/linux/mfd/dbx500-prcmu.h index bac942f959c..d7674eb7305 100644 --- a/include/linux/mfd/dbx500-prcmu.h +++ b/include/linux/mfd/dbx500-prcmu.h @@ -10,7 +10,7 @@ #include <linux/interrupt.h> #include <linux/notifier.h> -#include <asm/mach-types.h> +#include <linux/err.h> /* PRCMU Wakeup defines */ enum prcmu_wakeup_index { @@ -80,6 +80,29 @@ enum prcmu_wakeup_index { #define EPOD_STATE_ON_CLK_OFF 0x03 #define EPOD_STATE_ON 0x04 +/* DB5500 CLKOUT IDs */ +enum { + DB5500_CLKOUT0 = 0, + DB5500_CLKOUT1, +}; + +/* DB5500 CLKOUTx sources */ +enum { + DB5500_CLKOUT_REF_CLK_SEL0, + DB5500_CLKOUT_RTC_CLK0_SEL0, + DB5500_CLKOUT_ULP_CLK_SEL0, + DB5500_CLKOUT_STATIC0, + DB5500_CLKOUT_REFCLK, + DB5500_CLKOUT_ULPCLK, + DB5500_CLKOUT_ARMCLK, + DB5500_CLKOUT_SYSACC0CLK, + DB5500_CLKOUT_SOC0PLLCLK, + DB5500_CLKOUT_SOC1PLLCLK, + DB5500_CLKOUT_DDRPLLCLK, + DB5500_CLKOUT_TVCLK, + DB5500_CLKOUT_IRDACLK, +}; + /* * CLKOUT sources */ @@ -111,6 +134,7 @@ enum prcmu_clock { PRCMU_MSP1CLK, PRCMU_I2CCLK, PRCMU_SDMMCCLK, + PRCMU_SPARE1CLK, PRCMU_SLIMCLK, PRCMU_PER1CLK, PRCMU_PER2CLK, @@ -139,12 +163,20 @@ enum prcmu_clock { PRCMU_IRRCCLK, PRCMU_SIACLK, PRCMU_SVACLK, + PRCMU_ACLK, PRCMU_NUM_REG_CLOCKS, PRCMU_SYSCLK = PRCMU_NUM_REG_CLOCKS, + PRCMU_CDCLK, PRCMU_TIMCLK, PRCMU_PLLSOC0, PRCMU_PLLSOC1, PRCMU_PLLDDR, + PRCMU_PLLDSI, + PRCMU_DSI0CLK, + PRCMU_DSI1CLK, + PRCMU_DSI0ESCCLK, + PRCMU_DSI1ESCCLK, + PRCMU_DSI2ESCCLK, }; /** @@ -153,12 +185,14 @@ enum prcmu_clock { * @APE_NO_CHANGE: The APE operating point is unchanged * @APE_100_OPP: The new APE operating point is ape100opp * @APE_50_OPP: 50% + * @APE_50_PARTLY_25_OPP: 50%, except some clocks at 25%. */ enum ape_opp { APE_OPP_INIT = 0x00, APE_NO_CHANGE = 0x01, APE_100_OPP = 0x02, - APE_50_OPP = 0x03 + APE_50_OPP = 0x03, + APE_50_PARTLY_25_OPP = 0xFF, }; /** @@ -218,9 +252,11 @@ enum ddr_pwrst { #if defined(CONFIG_UX500_SOC_DB8500) || defined(CONFIG_UX500_SOC_DB5500) +#include <mach/id.h> + static inline void __init prcmu_early_init(void) { - if (machine_is_u5500()) + if (cpu_is_u5500()) return db5500_prcmu_early_init(); else return db8500_prcmu_early_init(); @@ -229,7 +265,7 @@ static inline void __init prcmu_early_init(void) static inline int prcmu_set_power_state(u8 state, bool keep_ulp_clk, bool keep_ap_pll) { - if (machine_is_u5500()) + if (cpu_is_u5500()) return db5500_prcmu_set_power_state(state, keep_ulp_clk, keep_ap_pll); else @@ -237,9 +273,65 @@ static inline int prcmu_set_power_state(u8 state, bool keep_ulp_clk, keep_ap_pll); } +static inline u8 prcmu_get_power_state_result(void) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_get_power_state_result(); +} + +static inline int prcmu_gic_decouple(void) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_gic_decouple(); +} + +static inline int prcmu_gic_recouple(void) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_gic_recouple(); +} + +static inline bool prcmu_gic_pending_irq(void) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_gic_pending_irq(); +} + +static inline bool prcmu_is_cpu_in_wfi(int cpu) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_is_cpu_in_wfi(cpu); +} + +static inline int prcmu_copy_gic_settings(void) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_copy_gic_settings(); +} + +static inline bool prcmu_pending_irq(void) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_pending_irq(); +} + static inline int prcmu_set_epod(u16 epod_id, u8 epod_state) { - if (machine_is_u5500()) + if (cpu_is_u5500()) return -EINVAL; else return db8500_prcmu_set_epod(epod_id, epod_state); @@ -247,7 +339,7 @@ static inline int prcmu_set_epod(u16 epod_id, u8 epod_state) static inline void prcmu_enable_wakeups(u32 wakeups) { - if (machine_is_u5500()) + if (cpu_is_u5500()) db5500_prcmu_enable_wakeups(wakeups); else db8500_prcmu_enable_wakeups(wakeups); @@ -260,7 +352,7 @@ static inline void prcmu_disable_wakeups(void) static inline void prcmu_config_abb_event_readout(u32 abb_events) { - if (machine_is_u5500()) + if (cpu_is_u5500()) db5500_prcmu_config_abb_event_readout(abb_events); else db8500_prcmu_config_abb_event_readout(abb_events); @@ -268,7 +360,7 @@ static inline void prcmu_config_abb_event_readout(u32 abb_events) static inline void prcmu_get_abb_event_buffer(void __iomem **buf) { - if (machine_is_u5500()) + if (cpu_is_u5500()) db5500_prcmu_get_abb_event_buffer(buf); else db8500_prcmu_get_abb_event_buffer(buf); @@ -276,25 +368,40 @@ static inline void prcmu_get_abb_event_buffer(void __iomem **buf) int prcmu_abb_read(u8 slave, u8 reg, u8 *value, u8 size); int prcmu_abb_write(u8 slave, u8 reg, u8 *value, u8 size); +int prcmu_abb_write_masked(u8 slave, u8 reg, u8 *value, u8 *mask, u8 size); int prcmu_config_clkout(u8 clkout, u8 source, u8 div); static inline int prcmu_request_clock(u8 clock, bool enable) { - if (machine_is_u5500()) + if (cpu_is_u5500()) return db5500_prcmu_request_clock(clock, enable); else return db8500_prcmu_request_clock(clock, enable); } -int prcmu_set_ape_opp(u8 opp); -int prcmu_get_ape_opp(void); -int prcmu_set_ddr_opp(u8 opp); -int prcmu_get_ddr_opp(void); +unsigned long prcmu_clock_rate(u8 clock); +long prcmu_round_clock_rate(u8 clock, unsigned long rate); +int prcmu_set_clock_rate(u8 clock, unsigned long rate); + +static inline int prcmu_set_ddr_opp(u8 opp) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_set_ddr_opp(opp); +} +static inline int prcmu_get_ddr_opp(void) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_get_ddr_opp(); +} static inline int prcmu_set_arm_opp(u8 opp) { - if (machine_is_u5500()) + if (cpu_is_u5500()) return -EINVAL; else return db8500_prcmu_set_arm_opp(opp); @@ -302,15 +409,31 @@ static inline int prcmu_set_arm_opp(u8 opp) static inline int prcmu_get_arm_opp(void) { - if (machine_is_u5500()) + if (cpu_is_u5500()) return -EINVAL; else return db8500_prcmu_get_arm_opp(); } +static inline int prcmu_set_ape_opp(u8 opp) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_set_ape_opp(opp); +} + +static inline int prcmu_get_ape_opp(void) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_get_ape_opp(); +} + static inline void prcmu_system_reset(u16 reset_code) { - if (machine_is_u5500()) + if (cpu_is_u5500()) return db5500_prcmu_system_reset(reset_code); else return db8500_prcmu_system_reset(reset_code); @@ -318,7 +441,7 @@ static inline void prcmu_system_reset(u16 reset_code) static inline u16 prcmu_get_reset_code(void) { - if (machine_is_u5500()) + if (cpu_is_u5500()) return db5500_prcmu_get_reset_code(); else return db8500_prcmu_get_reset_code(); @@ -326,10 +449,17 @@ static inline u16 prcmu_get_reset_code(void) void prcmu_ac_wake_req(void); void prcmu_ac_sleep_req(void); -void prcmu_modem_reset(void); +static inline void prcmu_modem_reset(void) +{ + if (cpu_is_u5500()) + return; + else + return db8500_prcmu_modem_reset(); +} + static inline bool prcmu_is_ac_wake_requested(void) { - if (machine_is_u5500()) + if (cpu_is_u5500()) return db5500_prcmu_is_ac_wake_requested(); else return db8500_prcmu_is_ac_wake_requested(); @@ -337,7 +467,7 @@ static inline bool prcmu_is_ac_wake_requested(void) static inline int prcmu_set_display_clocks(void) { - if (machine_is_u5500()) + if (cpu_is_u5500()) return db5500_prcmu_set_display_clocks(); else return db8500_prcmu_set_display_clocks(); @@ -345,7 +475,7 @@ static inline int prcmu_set_display_clocks(void) static inline int prcmu_disable_dsipll(void) { - if (machine_is_u5500()) + if (cpu_is_u5500()) return db5500_prcmu_disable_dsipll(); else return db8500_prcmu_disable_dsipll(); @@ -353,7 +483,7 @@ static inline int prcmu_disable_dsipll(void) static inline int prcmu_enable_dsipll(void) { - if (machine_is_u5500()) + if (cpu_is_u5500()) return db5500_prcmu_enable_dsipll(); else return db8500_prcmu_enable_dsipll(); @@ -361,11 +491,107 @@ static inline int prcmu_enable_dsipll(void) static inline int prcmu_config_esram0_deep_sleep(u8 state) { - if (machine_is_u5500()) + if (cpu_is_u5500()) return -EINVAL; else return db8500_prcmu_config_esram0_deep_sleep(state); } + +static inline int prcmu_config_hotdog(u8 threshold) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_config_hotdog(threshold); +} + +static inline int prcmu_config_hotmon(u8 low, u8 high) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_config_hotmon(low, high); +} + +static inline int prcmu_start_temp_sense(u16 cycles32k) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_start_temp_sense(cycles32k); +} + +static inline int prcmu_stop_temp_sense(void) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_stop_temp_sense(); +} + +static inline u32 prcmu_read(unsigned int reg) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_read(reg); +} + +static inline void prcmu_write(unsigned int reg, u32 value) +{ + if (cpu_is_u5500()) + return; + else + db8500_prcmu_write(reg, value); +} + +static inline void prcmu_write_masked(unsigned int reg, u32 mask, u32 value) +{ + if (cpu_is_u5500()) + return; + else + db8500_prcmu_write_masked(reg, mask, value); +} + +static inline int prcmu_enable_a9wdog(u8 id) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_enable_a9wdog(id); +} + +static inline int prcmu_disable_a9wdog(u8 id) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_disable_a9wdog(id); +} + +static inline int prcmu_kick_a9wdog(u8 id) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_kick_a9wdog(id); +} + +static inline int prcmu_load_a9wdog(u8 id, u32 timeout) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_load_a9wdog(id, timeout); +} + +static inline int prcmu_config_a9wdog(u8 num, bool sleep_auto_off) +{ + if (cpu_is_u5500()) + return -EINVAL; + else + return db8500_prcmu_config_a9wdog(num, sleep_auto_off); +} #else static inline void __init prcmu_early_init(void) {} @@ -395,6 +621,12 @@ static inline int prcmu_abb_write(u8 slave, u8 reg, u8 *value, u8 size) return -ENOSYS; } +static inline int prcmu_abb_write_masked(u8 slave, u8 reg, u8 *value, u8 *mask, + u8 size) +{ + return -ENOSYS; +} + static inline int prcmu_config_clkout(u8 clkout, u8 source, u8 div) { return 0; @@ -405,6 +637,21 @@ static inline int prcmu_request_clock(u8 clock, bool enable) return 0; } +static inline long prcmu_round_clock_rate(u8 clock, unsigned long rate) +{ + return 0; +} + +static inline int prcmu_set_clock_rate(u8 clock, unsigned long rate) +{ + return 0; +} + +static inline unsigned long prcmu_clock_rate(u8 clock) +{ + return 0; +} + static inline int prcmu_set_ape_opp(u8 opp) { return 0; @@ -480,14 +727,133 @@ static inline void prcmu_get_abb_event_buffer(void __iomem **buf) *buf = NULL; } +static inline int prcmu_config_hotdog(u8 threshold) +{ + return 0; +} + +static inline int prcmu_config_hotmon(u8 low, u8 high) +{ + return 0; +} + +static inline int prcmu_start_temp_sense(u16 cycles32k) +{ + return 0; +} + +static inline int prcmu_stop_temp_sense(void) +{ + return 0; +} + +static inline u32 prcmu_read(unsigned int reg) +{ + return 0; +} + +static inline void prcmu_write(unsigned int reg, u32 value) {} + +static inline void prcmu_write_masked(unsigned int reg, u32 mask, u32 value) {} + +#endif + +static inline void prcmu_set(unsigned int reg, u32 bits) +{ + prcmu_write_masked(reg, bits, bits); +} + +static inline void prcmu_clear(unsigned int reg, u32 bits) +{ + prcmu_write_masked(reg, bits, 0); +} + +#if defined(CONFIG_UX500_SOC_DB8500) || defined(CONFIG_UX500_SOC_DB5500) + +/** + * prcmu_enable_spi2 - Enables pin muxing for SPI2 on OtherAlternateC1. + */ +static inline void prcmu_enable_spi2(void) +{ + if (cpu_is_u8500()) + prcmu_set(DB8500_PRCM_GPIOCR, DB8500_PRCM_GPIOCR_SPI2_SELECT); +} + +/** + * prcmu_disable_spi2 - Disables pin muxing for SPI2 on OtherAlternateC1. + */ +static inline void prcmu_disable_spi2(void) +{ + if (cpu_is_u8500()) + prcmu_clear(DB8500_PRCM_GPIOCR, DB8500_PRCM_GPIOCR_SPI2_SELECT); +} + +/** + * prcmu_enable_stm_mod_uart - Enables pin muxing for STMMOD + * and UARTMOD on OtherAlternateC3. + */ +static inline void prcmu_enable_stm_mod_uart(void) +{ + if (cpu_is_u8500()) { + prcmu_set(DB8500_PRCM_GPIOCR, + (DB8500_PRCM_GPIOCR_DBG_STM_MOD_CMD1 | + DB8500_PRCM_GPIOCR_DBG_UARTMOD_CMD0)); + } +} + +/** + * prcmu_disable_stm_mod_uart - Disables pin muxing for STMMOD + * and UARTMOD on OtherAlternateC3. + */ +static inline void prcmu_disable_stm_mod_uart(void) +{ + if (cpu_is_u8500()) { + prcmu_clear(DB8500_PRCM_GPIOCR, + (DB8500_PRCM_GPIOCR_DBG_STM_MOD_CMD1 | + DB8500_PRCM_GPIOCR_DBG_UARTMOD_CMD0)); + } +} + +/** + * prcmu_enable_stm_ape - Enables pin muxing for STM APE on OtherAlternateC1. + */ +static inline void prcmu_enable_stm_ape(void) +{ + if (cpu_is_u8500()) { + prcmu_set(DB8500_PRCM_GPIOCR, + DB8500_PRCM_GPIOCR_DBG_STM_APE_CMD); + } +} + +/** + * prcmu_disable_stm_ape - Disables pin muxing for STM APE on OtherAlternateC1. + */ +static inline void prcmu_disable_stm_ape(void) +{ + if (cpu_is_u8500()) { + prcmu_clear(DB8500_PRCM_GPIOCR, + DB8500_PRCM_GPIOCR_DBG_STM_APE_CMD); + } +} + +#else + +static inline void prcmu_enable_spi2(void) {} +static inline void prcmu_disable_spi2(void) {} +static inline void prcmu_enable_stm_mod_uart(void) {} +static inline void prcmu_disable_stm_mod_uart(void) {} +static inline void prcmu_enable_stm_ape(void) {} +static inline void prcmu_disable_stm_ape(void) {} + #endif /* PRCMU QoS APE OPP class */ #define PRCMU_QOS_APE_OPP 1 #define PRCMU_QOS_DDR_OPP 2 +#define PRCMU_QOS_ARM_OPP 3 #define PRCMU_QOS_DEFAULT_VALUE -1 -#ifdef CONFIG_UX500_PRCMU_QOS_POWER +#ifdef CONFIG_DBX500_PRCMU_QOS_POWER unsigned long prcmu_qos_get_cpufreq_opp_delay(void); void prcmu_qos_set_cpufreq_opp_delay(unsigned long); diff --git a/include/linux/mfd/mc13xxx.h b/include/linux/mfd/mc13xxx.h index b86ee45c8b0..10e038bac8d 100644 --- a/include/linux/mfd/mc13xxx.h +++ b/include/linux/mfd/mc13xxx.h @@ -38,7 +38,8 @@ int mc13xxx_irq_ack(struct mc13xxx *mc13xxx, int irq); int mc13xxx_get_flags(struct mc13xxx *mc13xxx); int mc13xxx_adc_do_conversion(struct mc13xxx *mc13xxx, - unsigned int mode, unsigned int channel, unsigned int *sample); + unsigned int mode, unsigned int channel, + u8 ato, bool atox, unsigned int *sample); #define MC13XXX_IRQ_ADCDONE 0 #define MC13XXX_IRQ_ADCBISDONE 1 @@ -157,6 +158,18 @@ struct mc13xxx_buttons_platform_data { unsigned short b3on_key; }; +struct mc13xxx_ts_platform_data { + /* Delay between Touchscreen polarization and ADC Conversion. + * Given in clock ticks of a 32 kHz clock which gives a granularity of + * about 30.5ms */ + u8 ato; + +#define MC13783_TS_ATO_FIRST false +#define MC13783_TS_ATO_EACH true + /* Use the ATO delay only for the first conversion or for each one */ + bool atox; +}; + struct mc13xxx_platform_data { #define MC13XXX_USE_TOUCHSCREEN (1 << 0) #define MC13XXX_USE_CODEC (1 << 1) @@ -167,6 +180,7 @@ struct mc13xxx_platform_data { struct mc13xxx_regulator_platform_data regulators; struct mc13xxx_leds_platform_data *leds; struct mc13xxx_buttons_platform_data *buttons; + struct mc13xxx_ts_platform_data touch; }; #define MC13XXX_ADC_MODE_TS 1 diff --git a/include/linux/mfd/mcp.h b/include/linux/mfd/mcp.h index f88c1cc0cb0..a9e8bd15767 100644 --- a/include/linux/mfd/mcp.h +++ b/include/linux/mfd/mcp.h @@ -10,8 +10,6 @@ #ifndef MCP_H #define MCP_H -#include <mach/dma.h> - struct mcp_ops; struct mcp { @@ -21,12 +19,7 @@ struct mcp { int use_count; unsigned int sclk_rate; unsigned int rw_timeout; - dma_device_t dma_audio_rd; - dma_device_t dma_audio_wr; - dma_device_t dma_telco_rd; - dma_device_t dma_telco_wr; struct device attached_device; - int gpio_base; }; struct mcp_ops { @@ -47,15 +40,14 @@ void mcp_disable(struct mcp *); #define mcp_get_sclk_rate(mcp) ((mcp)->sclk_rate) struct mcp *mcp_host_alloc(struct device *, size_t); -int mcp_host_register(struct mcp *); -void mcp_host_unregister(struct mcp *); +int mcp_host_add(struct mcp *, void *); +void mcp_host_del(struct mcp *); +void mcp_host_free(struct mcp *); struct mcp_driver { struct device_driver drv; int (*probe)(struct mcp *); void (*remove)(struct mcp *); - int (*suspend)(struct mcp *, pm_message_t); - int (*resume)(struct mcp *); }; int mcp_driver_register(struct mcp_driver *); diff --git a/include/linux/mfd/rc5t583.h b/include/linux/mfd/rc5t583.h new file mode 100644 index 00000000000..a2c61609d21 --- /dev/null +++ b/include/linux/mfd/rc5t583.h @@ -0,0 +1,295 @@ +/* + * Core driver interface to access RICOH_RC5T583 power management chip. + * + * Copyright (c) 2011-2012, NVIDIA CORPORATION. All rights reserved. + * Author: Laxman dewangan <ldewangan@nvidia.com> + * + * Based on code + * Copyright (C) 2011 RICOH COMPANY,LTD + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + * + */ + +#ifndef __LINUX_MFD_RC5T583_H +#define __LINUX_MFD_RC5T583_H + +#include <linux/mutex.h> +#include <linux/types.h> + +#define RC5T583_MAX_REGS 0xF8 + +/* Maximum number of main interrupts */ +#define MAX_MAIN_INTERRUPT 5 +#define RC5T583_MAX_GPEDGE_REG 2 +#define RC5T583_MAX_INTERRUPT_MASK_REGS 9 + +/* Interrupt enable register */ +#define RC5T583_INT_EN_SYS1 0x19 +#define RC5T583_INT_EN_SYS2 0x1D +#define RC5T583_INT_EN_DCDC 0x41 +#define RC5T583_INT_EN_RTC 0xED +#define RC5T583_INT_EN_ADC1 0x90 +#define RC5T583_INT_EN_ADC2 0x91 +#define RC5T583_INT_EN_ADC3 0x92 + +/* Interrupt status registers (monitor regs in Ricoh)*/ +#define RC5T583_INTC_INTPOL 0xAD +#define RC5T583_INTC_INTEN 0xAE +#define RC5T583_INTC_INTMON 0xAF + +#define RC5T583_INT_MON_GRP 0xAF +#define RC5T583_INT_MON_SYS1 0x1B +#define RC5T583_INT_MON_SYS2 0x1F +#define RC5T583_INT_MON_DCDC 0x43 +#define RC5T583_INT_MON_RTC 0xEE + +/* Interrupt clearing registers */ +#define RC5T583_INT_IR_SYS1 0x1A +#define RC5T583_INT_IR_SYS2 0x1E +#define RC5T583_INT_IR_DCDC 0x42 +#define RC5T583_INT_IR_RTC 0xEE +#define RC5T583_INT_IR_ADCL 0x94 +#define RC5T583_INT_IR_ADCH 0x95 +#define RC5T583_INT_IR_ADCEND 0x96 +#define RC5T583_INT_IR_GPIOR 0xA9 +#define RC5T583_INT_IR_GPIOF 0xAA + +/* Sleep sequence registers */ +#define RC5T583_SLPSEQ1 0x21 +#define RC5T583_SLPSEQ2 0x22 +#define RC5T583_SLPSEQ3 0x23 +#define RC5T583_SLPSEQ4 0x24 +#define RC5T583_SLPSEQ5 0x25 +#define RC5T583_SLPSEQ6 0x26 +#define RC5T583_SLPSEQ7 0x27 +#define RC5T583_SLPSEQ8 0x28 +#define RC5T583_SLPSEQ9 0x29 +#define RC5T583_SLPSEQ10 0x2A +#define RC5T583_SLPSEQ11 0x2B + +/* Regulator registers */ +#define RC5T583_REG_DC0CTL 0x30 +#define RC5T583_REG_DC0DAC 0x31 +#define RC5T583_REG_DC0LATCTL 0x32 +#define RC5T583_REG_SR0CTL 0x33 + +#define RC5T583_REG_DC1CTL 0x34 +#define RC5T583_REG_DC1DAC 0x35 +#define RC5T583_REG_DC1LATCTL 0x36 +#define RC5T583_REG_SR1CTL 0x37 + +#define RC5T583_REG_DC2CTL 0x38 +#define RC5T583_REG_DC2DAC 0x39 +#define RC5T583_REG_DC2LATCTL 0x3A +#define RC5T583_REG_SR2CTL 0x3B + +#define RC5T583_REG_DC3CTL 0x3C +#define RC5T583_REG_DC3DAC 0x3D +#define RC5T583_REG_DC3LATCTL 0x3E +#define RC5T583_REG_SR3CTL 0x3F + + +#define RC5T583_REG_LDOEN1 0x50 +#define RC5T583_REG_LDOEN2 0x51 +#define RC5T583_REG_LDODIS1 0x52 +#define RC5T583_REG_LDODIS2 0x53 + +#define RC5T583_REG_LDO0DAC 0x54 +#define RC5T583_REG_LDO1DAC 0x55 +#define RC5T583_REG_LDO2DAC 0x56 +#define RC5T583_REG_LDO3DAC 0x57 +#define RC5T583_REG_LDO4DAC 0x58 +#define RC5T583_REG_LDO5DAC 0x59 +#define RC5T583_REG_LDO6DAC 0x5A +#define RC5T583_REG_LDO7DAC 0x5B +#define RC5T583_REG_LDO8DAC 0x5C +#define RC5T583_REG_LDO9DAC 0x5D + +#define RC5T583_REG_DC0DAC_DS 0x60 +#define RC5T583_REG_DC1DAC_DS 0x61 +#define RC5T583_REG_DC2DAC_DS 0x62 +#define RC5T583_REG_DC3DAC_DS 0x63 + +#define RC5T583_REG_LDO0DAC_DS 0x64 +#define RC5T583_REG_LDO1DAC_DS 0x65 +#define RC5T583_REG_LDO2DAC_DS 0x66 +#define RC5T583_REG_LDO3DAC_DS 0x67 +#define RC5T583_REG_LDO4DAC_DS 0x68 +#define RC5T583_REG_LDO5DAC_DS 0x69 +#define RC5T583_REG_LDO6DAC_DS 0x6A +#define RC5T583_REG_LDO7DAC_DS 0x6B +#define RC5T583_REG_LDO8DAC_DS 0x6C +#define RC5T583_REG_LDO9DAC_DS 0x6D + +/* GPIO register base address */ +#define RC5T583_GPIO_IOSEL 0xA0 +#define RC5T583_GPIO_PDEN 0xA1 +#define RC5T583_GPIO_IOOUT 0xA2 +#define RC5T583_GPIO_PGSEL 0xA3 +#define RC5T583_GPIO_GPINV 0xA4 +#define RC5T583_GPIO_GPDEB 0xA5 +#define RC5T583_GPIO_GPEDGE1 0xA6 +#define RC5T583_GPIO_GPEDGE2 0xA7 +#define RC5T583_GPIO_EN_INT 0xA8 +#define RC5T583_GPIO_MON_IOIN 0xAB +#define RC5T583_GPIO_GPOFUNC 0xAC + +/* RICOH_RC5T583 IRQ definitions */ +enum { + RC5T583_IRQ_ONKEY, + RC5T583_IRQ_ACOK, + RC5T583_IRQ_LIDOPEN, + RC5T583_IRQ_PREOT, + RC5T583_IRQ_CLKSTP, + RC5T583_IRQ_ONKEY_OFF, + RC5T583_IRQ_WD, + RC5T583_IRQ_EN_PWRREQ1, + RC5T583_IRQ_EN_PWRREQ2, + RC5T583_IRQ_PRE_VINDET, + + RC5T583_IRQ_DC0LIM, + RC5T583_IRQ_DC1LIM, + RC5T583_IRQ_DC2LIM, + RC5T583_IRQ_DC3LIM, + + RC5T583_IRQ_CTC, + RC5T583_IRQ_YALE, + RC5T583_IRQ_DALE, + RC5T583_IRQ_WALE, + + RC5T583_IRQ_AIN1L, + RC5T583_IRQ_AIN2L, + RC5T583_IRQ_AIN3L, + RC5T583_IRQ_VBATL, + RC5T583_IRQ_VIN3L, + RC5T583_IRQ_VIN8L, + RC5T583_IRQ_AIN1H, + RC5T583_IRQ_AIN2H, + RC5T583_IRQ_AIN3H, + RC5T583_IRQ_VBATH, + RC5T583_IRQ_VIN3H, + RC5T583_IRQ_VIN8H, + RC5T583_IRQ_ADCEND, + + RC5T583_IRQ_GPIO0, + RC5T583_IRQ_GPIO1, + RC5T583_IRQ_GPIO2, + RC5T583_IRQ_GPIO3, + RC5T583_IRQ_GPIO4, + RC5T583_IRQ_GPIO5, + RC5T583_IRQ_GPIO6, + RC5T583_IRQ_GPIO7, + + /* Should be last entry */ + RC5T583_MAX_IRQS, +}; + +/* Ricoh583 gpio definitions */ +enum { + RC5T583_GPIO0, + RC5T583_GPIO1, + RC5T583_GPIO2, + RC5T583_GPIO3, + RC5T583_GPIO4, + RC5T583_GPIO5, + RC5T583_GPIO6, + RC5T583_GPIO7, + + /* Should be last entry */ + RC5T583_MAX_GPIO, +}; + +enum { + RC5T583_DS_NONE, + RC5T583_DS_DC0, + RC5T583_DS_DC1, + RC5T583_DS_DC2, + RC5T583_DS_DC3, + RC5T583_DS_LDO0, + RC5T583_DS_LDO1, + RC5T583_DS_LDO2, + RC5T583_DS_LDO3, + RC5T583_DS_LDO4, + RC5T583_DS_LDO5, + RC5T583_DS_LDO6, + RC5T583_DS_LDO7, + RC5T583_DS_LDO8, + RC5T583_DS_LDO9, + RC5T583_DS_PSO0, + RC5T583_DS_PSO1, + RC5T583_DS_PSO2, + RC5T583_DS_PSO3, + RC5T583_DS_PSO4, + RC5T583_DS_PSO5, + RC5T583_DS_PSO6, + RC5T583_DS_PSO7, + + /* Should be last entry */ + RC5T583_DS_MAX, +}; + +/* + * Ricoh pmic RC5T583 supports sleep through two external controls. + * The output of gpios and regulator can be enable/disable through + * this external signals. + */ +enum { + RC5T583_EXT_PWRREQ1_CONTROL = 0x1, + RC5T583_EXT_PWRREQ2_CONTROL = 0x2, +}; + +struct rc5t583 { + struct device *dev; + struct regmap *regmap; + int chip_irq; + int irq_base; + struct mutex irq_lock; + unsigned long group_irq_en[MAX_MAIN_INTERRUPT]; + + /* For main interrupt bits in INTC */ + uint8_t intc_inten_reg; + + /* For group interrupt bits and address */ + uint8_t irq_en_reg[RC5T583_MAX_INTERRUPT_MASK_REGS]; + + /* For gpio edge */ + uint8_t gpedge_reg[RC5T583_MAX_GPEDGE_REG]; +}; + +/* + * rc5t583_platform_data: Platform data for ricoh rc5t583 pmu. + * The board specific data is provided through this structure. + * @irq_base: Irq base number on which this device registers their interrupts. + * @enable_shutdown: Enable shutdown through the input pin "shutdown". + */ + +struct rc5t583_platform_data { + int irq_base; + bool enable_shutdown; +}; + +int rc5t583_write(struct device *dev, u8 reg, uint8_t val); +int rc5t583_read(struct device *dev, uint8_t reg, uint8_t *val); +int rc5t583_set_bits(struct device *dev, unsigned int reg, + unsigned int bit_mask); +int rc5t583_clear_bits(struct device *dev, unsigned int reg, + unsigned int bit_mask); +int rc5t583_update(struct device *dev, unsigned int reg, + unsigned int val, unsigned int mask); +int rc5t583_ext_power_req_config(struct device *dev, int deepsleep_id, + int ext_pwr_req, int deepsleep_slot_nr); +int rc5t583_irq_init(struct rc5t583 *rc5t583, int irq, int irq_base); +int rc5t583_irq_exit(struct rc5t583 *rc5t583); + +#endif diff --git a/include/linux/mfd/stmpe.h b/include/linux/mfd/stmpe.h index 8c54de674b4..8516fd1eaab 100644 --- a/include/linux/mfd/stmpe.h +++ b/include/linux/mfd/stmpe.h @@ -28,6 +28,7 @@ enum stmpe_partnum { STMPE1601, STMPE2401, STMPE2403, + STMPE_NBR_PARTS }; /* diff --git a/include/linux/mfd/tmio.h b/include/linux/mfd/tmio.h index 0dc98044d8b..f5171dbf885 100644 --- a/include/linux/mfd/tmio.h +++ b/include/linux/mfd/tmio.h @@ -1,8 +1,10 @@ #ifndef MFD_TMIO_H #define MFD_TMIO_H +#include <linux/device.h> #include <linux/fb.h> #include <linux/io.h> +#include <linux/jiffies.h> #include <linux/platform_device.h> #include <linux/pm_runtime.h> @@ -64,8 +66,8 @@ #define TMIO_MMC_SDIO_IRQ (1 << 2) /* * Some platforms can detect card insertion events with controller powered - * down, in which case they have to call tmio_mmc_cd_wakeup() to power up the - * controller and report the event to the driver. + * down, using a GPIO IRQ, in which case they have to fill in cd_irq, cd_gpio, + * and cd_flags fields of struct tmio_mmc_data. */ #define TMIO_MMC_HAS_COLD_CD (1 << 3) /* @@ -73,6 +75,12 @@ * idle before writing to some registers. */ #define TMIO_MMC_HAS_IDLE_WAIT (1 << 4) +/* + * A GPIO is used for card hotplug detection. We need an extra flag for this, + * because 0 is a valid GPIO number too, and requiring users to specify + * cd_gpio < 0 to disable GPIO hotplug would break backwards compatibility. + */ +#define TMIO_MMC_USE_GPIO_CD (1 << 5) int tmio_core_mmc_enable(void __iomem *cnf, int shift, unsigned long base); int tmio_core_mmc_resume(void __iomem *cnf, int shift, unsigned long base); @@ -97,19 +105,23 @@ struct tmio_mmc_data { u32 ocr_mask; /* available voltages */ struct tmio_mmc_dma *dma; struct device *dev; - bool power; + unsigned int cd_gpio; void (*set_pwr)(struct platform_device *host, int state); void (*set_clk_div)(struct platform_device *host, int state); int (*get_cd)(struct platform_device *host); int (*write16_hook)(struct tmio_mmc_host *host, int addr); }; +/* + * This function is deprecated and will be removed soon. Please, convert your + * platform to use drivers/mmc/core/cd-gpio.c + */ +#include <linux/mmc/host.h> static inline void tmio_mmc_cd_wakeup(struct tmio_mmc_data *pdata) { - if (pdata && !pdata->power) { - pdata->power = true; - pm_runtime_get(pdata->dev); - } + if (pdata) + mmc_detect_change(dev_get_drvdata(pdata->dev), + msecs_to_jiffies(100)); } /* diff --git a/include/linux/mfd/tps65090.h b/include/linux/mfd/tps65090.h new file mode 100644 index 00000000000..38e31c55adb --- /dev/null +++ b/include/linux/mfd/tps65090.h @@ -0,0 +1,46 @@ +/* + * Core driver interface for TI TPS65090 PMIC family + * + * Copyright (C) 2012 NVIDIA Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. + * + */ + +#ifndef __LINUX_MFD_TPS65090_H +#define __LINUX_MFD_TPS65090_H + +struct tps65090_subdev_info { + int id; + const char *name; + void *platform_data; +}; + +struct tps65090_platform_data { + int irq_base; + int num_subdevs; + struct tps65090_subdev_info *subdevs; +}; + +/* + * NOTE: the functions below are not intended for use outside + * of the TPS65090 sub-device drivers + */ +extern int tps65090_write(struct device *dev, int reg, uint8_t val); +extern int tps65090_read(struct device *dev, int reg, uint8_t *val); +extern int tps65090_set_bits(struct device *dev, int reg, uint8_t bit_num); +extern int tps65090_clr_bits(struct device *dev, int reg, uint8_t bit_num); + +#endif /*__LINUX_MFD_TPS65090_H */ diff --git a/include/linux/mfd/tps65217.h b/include/linux/mfd/tps65217.h new file mode 100644 index 00000000000..e030ef9a64e --- /dev/null +++ b/include/linux/mfd/tps65217.h @@ -0,0 +1,283 @@ +/* + * linux/mfd/tps65217.h + * + * Functions to access TPS65217 power management chip. + * + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation version 2. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __LINUX_MFD_TPS65217_H +#define __LINUX_MFD_TPS65217_H + +#include <linux/i2c.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/machine.h> + +/* I2C ID for TPS65217 part */ +#define TPS65217_I2C_ID 0x24 + +/* All register addresses */ +#define TPS65217_REG_CHIPID 0X00 +#define TPS65217_REG_PPATH 0X01 +#define TPS65217_REG_INT 0X02 +#define TPS65217_REG_CHGCONFIG0 0X03 +#define TPS65217_REG_CHGCONFIG1 0X04 +#define TPS65217_REG_CHGCONFIG2 0X05 +#define TPS65217_REG_CHGCONFIG3 0X06 +#define TPS65217_REG_WLEDCTRL1 0X07 +#define TPS65217_REG_WLEDCTRL2 0X08 +#define TPS65217_REG_MUXCTRL 0X09 +#define TPS65217_REG_STATUS 0X0A +#define TPS65217_REG_PASSWORD 0X0B +#define TPS65217_REG_PGOOD 0X0C +#define TPS65217_REG_DEFPG 0X0D +#define TPS65217_REG_DEFDCDC1 0X0E +#define TPS65217_REG_DEFDCDC2 0X0F +#define TPS65217_REG_DEFDCDC3 0X10 +#define TPS65217_REG_DEFSLEW 0X11 +#define TPS65217_REG_DEFLDO1 0X12 +#define TPS65217_REG_DEFLDO2 0X13 +#define TPS65217_REG_DEFLS1 0X14 +#define TPS65217_REG_DEFLS2 0X15 +#define TPS65217_REG_ENABLE 0X16 +#define TPS65217_REG_DEFUVLO 0X18 +#define TPS65217_REG_SEQ1 0X19 +#define TPS65217_REG_SEQ2 0X1A +#define TPS65217_REG_SEQ3 0X1B +#define TPS65217_REG_SEQ4 0X1C +#define TPS65217_REG_SEQ5 0X1D +#define TPS65217_REG_SEQ6 0X1E + +/* Register field definitions */ +#define TPS65217_CHIPID_CHIP_MASK 0xF0 +#define TPS65217_CHIPID_REV_MASK 0x0F + +#define TPS65217_PPATH_ACSINK_ENABLE BIT(7) +#define TPS65217_PPATH_USBSINK_ENABLE BIT(6) +#define TPS65217_PPATH_AC_PW_ENABLE BIT(5) +#define TPS65217_PPATH_USB_PW_ENABLE BIT(4) +#define TPS65217_PPATH_AC_CURRENT_MASK 0x0C +#define TPS65217_PPATH_USB_CURRENT_MASK 0x03 + +#define TPS65217_INT_PBM BIT(6) +#define TPS65217_INT_ACM BIT(5) +#define TPS65217_INT_USBM BIT(4) +#define TPS65217_INT_PBI BIT(2) +#define TPS65217_INT_ACI BIT(1) +#define TPS65217_INT_USBI BIT(0) + +#define TPS65217_CHGCONFIG0_TREG BIT(7) +#define TPS65217_CHGCONFIG0_DPPM BIT(6) +#define TPS65217_CHGCONFIG0_TSUSP BIT(5) +#define TPS65217_CHGCONFIG0_TERMI BIT(4) +#define TPS65217_CHGCONFIG0_ACTIVE BIT(3) +#define TPS65217_CHGCONFIG0_CHGTOUT BIT(2) +#define TPS65217_CHGCONFIG0_PCHGTOUT BIT(1) +#define TPS65217_CHGCONFIG0_BATTEMP BIT(0) + +#define TPS65217_CHGCONFIG1_TMR_MASK 0xC0 +#define TPS65217_CHGCONFIG1_TMR_ENABLE BIT(5) +#define TPS65217_CHGCONFIG1_NTC_TYPE BIT(4) +#define TPS65217_CHGCONFIG1_RESET BIT(3) +#define TPS65217_CHGCONFIG1_TERM BIT(2) +#define TPS65217_CHGCONFIG1_SUSP BIT(1) +#define TPS65217_CHGCONFIG1_CHG_EN BIT(0) + +#define TPS65217_CHGCONFIG2_DYNTMR BIT(7) +#define TPS65217_CHGCONFIG2_VPREGHG BIT(6) +#define TPS65217_CHGCONFIG2_VOREG_MASK 0x30 + +#define TPS65217_CHGCONFIG3_ICHRG_MASK 0xC0 +#define TPS65217_CHGCONFIG3_DPPMTH_MASK 0x30 +#define TPS65217_CHGCONFIG2_PCHRGT BIT(3) +#define TPS65217_CHGCONFIG2_TERMIF 0x06 +#define TPS65217_CHGCONFIG2_TRANGE BIT(0) + +#define TPS65217_WLEDCTRL1_ISINK_ENABLE BIT(3) +#define TPS65217_WLEDCTRL1_ISEL BIT(2) +#define TPS65217_WLEDCTRL1_FDIM_MASK 0x03 + +#define TPS65217_WLEDCTRL2_DUTY_MASK 0x7F + +#define TPS65217_MUXCTRL_MUX_MASK 0x07 + +#define TPS65217_STATUS_OFF BIT(7) +#define TPS65217_STATUS_ACPWR BIT(3) +#define TPS65217_STATUS_USBPWR BIT(2) +#define TPS65217_STATUS_PB BIT(0) + +#define TPS65217_PASSWORD_REGS_UNLOCK 0x7D + +#define TPS65217_PGOOD_LDO3_PG BIT(6) +#define TPS65217_PGOOD_LDO4_PG BIT(5) +#define TPS65217_PGOOD_DC1_PG BIT(4) +#define TPS65217_PGOOD_DC2_PG BIT(3) +#define TPS65217_PGOOD_DC3_PG BIT(2) +#define TPS65217_PGOOD_LDO1_PG BIT(1) +#define TPS65217_PGOOD_LDO2_PG BIT(0) + +#define TPS65217_DEFPG_LDO1PGM BIT(3) +#define TPS65217_DEFPG_LDO2PGM BIT(2) +#define TPS65217_DEFPG_PGDLY_MASK 0x03 + +#define TPS65217_DEFDCDCX_XADJX BIT(7) +#define TPS65217_DEFDCDCX_DCDC_MASK 0x3F + +#define TPS65217_DEFSLEW_GO BIT(7) +#define TPS65217_DEFSLEW_GODSBL BIT(6) +#define TPS65217_DEFSLEW_PFM_EN1 BIT(5) +#define TPS65217_DEFSLEW_PFM_EN2 BIT(4) +#define TPS65217_DEFSLEW_PFM_EN3 BIT(3) +#define TPS65217_DEFSLEW_SLEW_MASK 0x07 + +#define TPS65217_DEFLDO1_LDO1_MASK 0x0F + +#define TPS65217_DEFLDO2_TRACK BIT(6) +#define TPS65217_DEFLDO2_LDO2_MASK 0x3F + +#define TPS65217_DEFLDO3_LDO3_EN BIT(5) +#define TPS65217_DEFLDO3_LDO3_MASK 0x1F + +#define TPS65217_DEFLDO4_LDO4_EN BIT(5) +#define TPS65217_DEFLDO4_LDO4_MASK 0x1F + +#define TPS65217_ENABLE_LS1_EN BIT(6) +#define TPS65217_ENABLE_LS2_EN BIT(5) +#define TPS65217_ENABLE_DC1_EN BIT(4) +#define TPS65217_ENABLE_DC2_EN BIT(3) +#define TPS65217_ENABLE_DC3_EN BIT(2) +#define TPS65217_ENABLE_LDO1_EN BIT(1) +#define TPS65217_ENABLE_LDO2_EN BIT(0) + +#define TPS65217_DEFUVLO_UVLOHYS BIT(2) +#define TPS65217_DEFUVLO_UVLO_MASK 0x03 + +#define TPS65217_SEQ1_DC1_SEQ_MASK 0xF0 +#define TPS65217_SEQ1_DC2_SEQ_MASK 0x0F + +#define TPS65217_SEQ2_DC3_SEQ_MASK 0xF0 +#define TPS65217_SEQ2_LDO1_SEQ_MASK 0x0F + +#define TPS65217_SEQ3_LDO2_SEQ_MASK 0xF0 +#define TPS65217_SEQ3_LDO3_SEQ_MASK 0x0F + +#define TPS65217_SEQ4_LDO4_SEQ_MASK 0xF0 + +#define TPS65217_SEQ5_DLY1_MASK 0xC0 +#define TPS65217_SEQ5_DLY2_MASK 0x30 +#define TPS65217_SEQ5_DLY3_MASK 0x0C +#define TPS65217_SEQ5_DLY4_MASK 0x03 + +#define TPS65217_SEQ6_DLY5_MASK 0xC0 +#define TPS65217_SEQ6_DLY6_MASK 0x30 +#define TPS65217_SEQ6_SEQUP BIT(2) +#define TPS65217_SEQ6_SEQDWN BIT(1) +#define TPS65217_SEQ6_INSTDWN BIT(0) + +#define TPS65217_MAX_REGISTER 0x1E +#define TPS65217_PROTECT_NONE 0 +#define TPS65217_PROTECT_L1 1 +#define TPS65217_PROTECT_L2 2 + + +enum tps65217_regulator_id { + /* DCDC's */ + TPS65217_DCDC_1, + TPS65217_DCDC_2, + TPS65217_DCDC_3, + /* LDOs */ + TPS65217_LDO_1, + TPS65217_LDO_2, + TPS65217_LDO_3, + TPS65217_LDO_4, +}; + +#define TPS65217_MAX_REG_ID TPS65217_LDO_4 + +/* Number of step-down converters available */ +#define TPS65217_NUM_DCDC 3 +/* Number of LDO voltage regulators available */ +#define TPS65217_NUM_LDO 4 +/* Number of total regulators available */ +#define TPS65217_NUM_REGULATOR (TPS65217_NUM_DCDC + TPS65217_NUM_LDO) + +/** + * struct tps65217_board - packages regulator init data + * @tps65217_regulator_data: regulator initialization values + * + * Board data may be used to initialize regulator. + */ +struct tps65217_board { + struct regulator_init_data *tps65217_init_data; +}; + +/** + * struct tps_info - packages regulator constraints + * @name: Voltage regulator name + * @min_uV: minimum micro volts + * @max_uV: minimum micro volts + * @vsel_to_uv: Function pointer to get voltage from selector + * @uv_to_vsel: Function pointer to get selector from voltage + * @table: Table for non-uniform voltage step-size + * @table_len: Length of the voltage table + * @enable_mask: Regulator enable mask bits + * @set_vout_reg: Regulator output voltage set register + * @set_vout_mask: Regulator output voltage set mask + * + * This data is used to check the regualtor voltage limits while setting. + */ +struct tps_info { + const char *name; + int min_uV; + int max_uV; + int (*vsel_to_uv)(unsigned int vsel); + int (*uv_to_vsel)(int uV, unsigned int *vsel); + const int *table; + unsigned int table_len; + unsigned int enable_mask; + unsigned int set_vout_reg; + unsigned int set_vout_mask; +}; + +/** + * struct tps65217 - tps65217 sub-driver chip access routines + * + * Device data may be used to access the TPS65217 chip + */ + +struct tps65217 { + struct device *dev; + struct tps65217_board *pdata; + struct regulator_desc desc[TPS65217_NUM_REGULATOR]; + struct regulator_dev *rdev[TPS65217_NUM_REGULATOR]; + struct tps_info *info[TPS65217_NUM_REGULATOR]; + struct regmap *regmap; + + /* Client devices */ + struct platform_device *regulator_pdev[TPS65217_NUM_REGULATOR]; +}; + +static inline struct tps65217 *dev_to_tps65217(struct device *dev) +{ + return dev_get_drvdata(dev); +} + +int tps65217_reg_read(struct tps65217 *tps, unsigned int reg, + unsigned int *val); +int tps65217_reg_write(struct tps65217 *tps, unsigned int reg, + unsigned int val, unsigned int level); +int tps65217_set_bits(struct tps65217 *tps, unsigned int reg, + unsigned int mask, unsigned int val, unsigned int level); +int tps65217_clear_bits(struct tps65217 *tps, unsigned int reg, + unsigned int mask, unsigned int level); + +#endif /* __LINUX_MFD_TPS65217_H */ diff --git a/include/linux/mfd/tps65910.h b/include/linux/mfd/tps65910.h index 76700b5eee9..1c6c2860d1a 100644 --- a/include/linux/mfd/tps65910.h +++ b/include/linux/mfd/tps65910.h @@ -17,6 +17,8 @@ #ifndef __LINUX_MFD_TPS65910_H #define __LINUX_MFD_TPS65910_H +#include <linux/gpio.h> + /* TPS chip id list */ #define TPS65910 0 #define TPS65911 1 @@ -657,6 +659,8 @@ /*Register GPIO (0x80) register.RegisterDescription */ +#define GPIO_SLEEP_MASK 0x80 +#define GPIO_SLEEP_SHIFT 7 #define GPIO_DEB_MASK 0x10 #define GPIO_DEB_SHIFT 4 #define GPIO_PUEN_MASK 0x08 @@ -740,6 +744,11 @@ #define TPS65910_GPIO_STS BIT(1) #define TPS65910_GPIO_SET BIT(0) +/* Max number of TPS65910/11 GPIOs */ +#define TPS65910_NUM_GPIO 6 +#define TPS65911_NUM_GPIO 9 +#define TPS6591X_MAX_NUM_GPIO 9 + /* Regulator Index Definitions */ #define TPS65910_REG_VRTC 0 #define TPS65910_REG_VIO 1 @@ -785,6 +794,7 @@ struct tps65910_board { int irq_base; int vmbch_threshold; int vmbch2_threshold; + bool en_gpio_sleep[TPS6591X_MAX_NUM_GPIO]; unsigned long regulator_ext_sleep_control[TPS65910_NUM_REGS]; struct regulator_init_data *tps65910_pmic_init_data[TPS65910_NUM_REGS]; }; @@ -796,6 +806,7 @@ struct tps65910_board { struct tps65910 { struct device *dev; struct i2c_client *i2c_client; + struct regmap *regmap; struct mutex io_mutex; unsigned int id; int (*read)(struct tps65910 *tps65910, u8 reg, int size, void *dest); diff --git a/include/linux/mfd/ucb1x00.h b/include/linux/mfd/ucb1x00.h index 4321f044d1e..28af4175636 100644 --- a/include/linux/mfd/ucb1x00.h +++ b/include/linux/mfd/ucb1x00.h @@ -12,7 +12,7 @@ #include <linux/mfd/mcp.h> #include <linux/gpio.h> -#include <linux/semaphore.h> +#include <linux/mutex.h> #define UCB_IO_DATA 0x00 #define UCB_IO_DIR 0x01 @@ -104,17 +104,27 @@ #define UCB_MODE_DYN_VFLAG_ENA (1 << 12) #define UCB_MODE_AUD_OFF_CAN (1 << 13) +enum ucb1x00_reset { + UCB_RST_PROBE, + UCB_RST_RESUME, + UCB_RST_SUSPEND, + UCB_RST_REMOVE, + UCB_RST_PROBE_FAIL, +}; -struct ucb1x00_irq { - void *devid; - void (*fn)(int, void *); +struct ucb1x00_plat_data { + void (*reset)(enum ucb1x00_reset); + unsigned irq_base; + int gpio_base; + unsigned can_wakeup; }; struct ucb1x00 { - spinlock_t lock; + raw_spinlock_t irq_lock; struct mcp *mcp; unsigned int irq; - struct semaphore adc_sem; + int irq_base; + struct mutex adc_mutex; spinlock_t io_lock; u16 id; u16 io_dir; @@ -122,7 +132,8 @@ struct ucb1x00 { u16 adc_cr; u16 irq_fal_enbl; u16 irq_ris_enbl; - struct ucb1x00_irq irq_handler[16]; + u16 irq_mask; + u16 irq_wake; struct device dev; struct list_head node; struct list_head devs; @@ -144,7 +155,7 @@ struct ucb1x00_driver { struct list_head devs; int (*add)(struct ucb1x00_dev *dev); void (*remove)(struct ucb1x00_dev *dev); - int (*suspend)(struct ucb1x00_dev *dev, pm_message_t state); + int (*suspend)(struct ucb1x00_dev *dev); int (*resume)(struct ucb1x00_dev *dev); }; @@ -245,15 +256,4 @@ unsigned int ucb1x00_adc_read(struct ucb1x00 *ucb, int adc_channel, int sync); void ucb1x00_adc_enable(struct ucb1x00 *ucb); void ucb1x00_adc_disable(struct ucb1x00 *ucb); -/* - * Which edges of the IRQ do you want to control today? - */ -#define UCB_RISING (1 << 0) -#define UCB_FALLING (1 << 1) - -int ucb1x00_hook_irq(struct ucb1x00 *ucb, unsigned int idx, void (*fn)(int, void *), void *devid); -void ucb1x00_enable_irq(struct ucb1x00 *ucb, unsigned int idx, int edges); -void ucb1x00_disable_irq(struct ucb1x00 *ucb, unsigned int idx, int edges); -int ucb1x00_free_irq(struct ucb1x00 *ucb, unsigned int idx, void *devid); - #endif diff --git a/include/linux/mfd/wm8994/pdata.h b/include/linux/mfd/wm8994/pdata.h index dc3e0501168..893267bb622 100644 --- a/include/linux/mfd/wm8994/pdata.h +++ b/include/linux/mfd/wm8994/pdata.h @@ -22,7 +22,6 @@ struct wm8994_ldo_pdata { /** GPIOs to enable regulator, 0 or less if not available */ int enable; - const char *supply; const struct regulator_init_data *init_data; }; diff --git a/include/linux/mm.h b/include/linux/mm.h index cf798233610..d8738a464b9 100644 --- a/include/linux/mm.h +++ b/include/linux/mm.h @@ -954,7 +954,7 @@ extern void truncate_pagecache(struct inode *inode, loff_t old, loff_t new); extern void truncate_setsize(struct inode *inode, loff_t newsize); extern int vmtruncate(struct inode *inode, loff_t offset); extern int vmtruncate_range(struct inode *inode, loff_t offset, loff_t end); - +void truncate_pagecache_range(struct inode *inode, loff_t offset, loff_t end); int truncate_inode_page(struct address_space *mapping, struct page *page); int generic_error_remove_page(struct address_space *mapping, struct page *page); @@ -1258,6 +1258,8 @@ static inline void pgtable_page_dtor(struct page *page) extern void free_area_init(unsigned long * zones_size); extern void free_area_init_node(int nid, unsigned long * zones_size, unsigned long zone_start_pfn, unsigned long *zholes_size); +extern void free_initmem(void); + #ifdef CONFIG_HAVE_MEMBLOCK_NODE_MAP /* * With CONFIG_HAVE_MEMBLOCK_NODE_MAP set, an architecture may initialise its diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h index 6faa145c81e..01beae78f07 100644 --- a/include/linux/mmc/card.h +++ b/include/linux/mmc/card.h @@ -72,6 +72,8 @@ struct mmc_ext_csd { bool hpi_en; /* HPI enablebit */ bool hpi; /* HPI support bit */ unsigned int hpi_cmd; /* cmd used as HPI */ + unsigned int data_sector_size; /* 512 bytes or 4KB */ + unsigned int data_tag_unit_size; /* DATA TAG UNIT size */ unsigned int boot_ro_lock; /* ro lock support */ bool boot_ro_lockable; u8 raw_partition_support; /* 160 */ diff --git a/include/linux/mmc/cd-gpio.h b/include/linux/mmc/cd-gpio.h index a8e46978331..cefaba038cc 100644 --- a/include/linux/mmc/cd-gpio.h +++ b/include/linux/mmc/cd-gpio.h @@ -12,8 +12,7 @@ #define MMC_CD_GPIO_H struct mmc_host; -int mmc_cd_gpio_request(struct mmc_host *host, unsigned int gpio, - unsigned int irq, unsigned long flags); +int mmc_cd_gpio_request(struct mmc_host *host, unsigned int gpio); void mmc_cd_gpio_free(struct mmc_host *host); #endif diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h index 2e6a681fceb..1b431c728b9 100644 --- a/include/linux/mmc/core.h +++ b/include/linux/mmc/core.h @@ -175,7 +175,6 @@ extern unsigned int mmc_align_data_size(struct mmc_card *, unsigned int); extern int __mmc_claim_host(struct mmc_host *host, atomic_t *abort); extern void mmc_release_host(struct mmc_host *host); -extern void mmc_do_release_host(struct mmc_host *host); extern int mmc_try_claim_host(struct mmc_host *host); extern int mmc_flush_cache(struct mmc_card *); diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h index aae5d1f1bb3..8f66e28f5a0 100644 --- a/include/linux/mmc/dw_mmc.h +++ b/include/linux/mmc/dw_mmc.h @@ -76,7 +76,7 @@ struct mmc_data; * @num_slots: Number of slots available. * @verid: Denote Version ID. * @data_offset: Set the offset of DATA register according to VERID. - * @pdev: Platform device associated with the MMC controller. + * @dev: Device associated with the MMC controller. * @pdata: Platform data associated with the MMC controller. * @slot: Slots sharing this MMC controller. * @fifo_depth: depth of FIFO. @@ -87,6 +87,8 @@ struct mmc_data; * @push_data: Pointer to FIFO push function. * @pull_data: Pointer to FIFO pull function. * @quirks: Set of quirks that apply to specific versions of the IP. + * @irq_flags: The flags to be passed to request_irq. + * @irq: The irq value to be passed to request_irq. * * Locking * ======= @@ -153,7 +155,7 @@ struct dw_mci { u32 fifoth_val; u16 verid; u16 data_offset; - struct platform_device *pdev; + struct device dev; struct dw_mci_board *pdata; struct dw_mci_slot *slot[MAX_MCI_SLOTS]; @@ -174,6 +176,8 @@ struct dw_mci { u32 quirks; struct regulator *vmmc; /* Power regulator */ + unsigned long irq_flags; /* IRQ flags */ + unsigned int irq; }; /* DMA ops for Internal/External DMAC interface */ diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h index 91924e8c642..cbde4b7e675 100644 --- a/include/linux/mmc/host.h +++ b/include/linux/mmc/host.h @@ -81,34 +81,11 @@ struct mmc_ios { struct mmc_host_ops { /* - * Hosts that support power saving can use the 'enable' and 'disable' - * methods to exit and enter power saving states. 'enable' is called - * when the host is claimed and 'disable' is called (or scheduled with - * a delay) when the host is released. The 'disable' is scheduled if - * the disable delay set by 'mmc_set_disable_delay()' is non-zero, - * otherwise 'disable' is called immediately. 'disable' may be - * scheduled repeatedly, to permit ever greater power saving at the - * expense of ever greater latency to re-enable. Rescheduling is - * determined by the return value of the 'disable' method. A positive - * value gives the delay in milliseconds. - * - * In the case where a host function (like set_ios) may be called - * with or without the host claimed, enabling and disabling can be - * done directly and will nest correctly. Call 'mmc_host_enable()' and - * 'mmc_host_lazy_disable()' for this purpose, but note that these - * functions must be paired. - * - * Alternatively, 'mmc_host_enable()' may be paired with - * 'mmc_host_disable()' which calls 'disable' immediately. In this - * case the 'disable' method will be called with 'lazy' set to 0. - * This is mainly useful for error paths. - * - * Because lazy disable may be called from a work queue, the 'disable' - * method must claim the host when 'lazy' != 0, which will work - * correctly because recursion is detected and handled. + * 'enable' is called when the host is claimed and 'disable' is called + * when the host is released. 'enable' and 'disable' are deprecated. */ int (*enable)(struct mmc_host *host); - int (*disable)(struct mmc_host *host, int lazy); + int (*disable)(struct mmc_host *host); /* * It is optional for the host to implement pre_req and post_req in * order to support double buffering of requests (prepare one @@ -219,7 +196,7 @@ struct mmc_host { #define MMC_CAP_SPI (1 << 4) /* Talks only SPI protocols */ #define MMC_CAP_NEEDS_POLL (1 << 5) /* Needs polling for card-detection */ #define MMC_CAP_8_BIT_DATA (1 << 6) /* Can the host do 8 bit transfers */ -#define MMC_CAP_DISABLE (1 << 7) /* Can the host be disabled */ + #define MMC_CAP_NONREMOVABLE (1 << 8) /* Nonremovable e.g. eMMC */ #define MMC_CAP_WAIT_WHILE_BUSY (1 << 9) /* Waits while card is busy */ #define MMC_CAP_ERASE (1 << 10) /* Allow erase/trim commands */ @@ -259,6 +236,8 @@ struct mmc_host { #define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \ MMC_CAP2_HS200_1_2V_SDR) #define MMC_CAP2_BROKEN_VOLTAGE (1 << 7) /* Use the broken voltage */ +#define MMC_CAP2_DETECT_ON_ERR (1 << 8) /* On I/O err check card removal */ +#define MMC_CAP2_HC_ERASE_SZ (1 << 9) /* High-capacity erase size */ mmc_pm_flag_t pm_caps; /* supported pm features */ unsigned int power_notify_type; @@ -301,13 +280,7 @@ struct mmc_host { unsigned int removed:1; /* host is being removed */ #endif - /* Only used with MMC_CAP_DISABLE */ - int enabled; /* host is enabled */ int rescan_disable; /* disable card detection */ - int nesting_cnt; /* "enable" nesting count */ - int en_dis_recurs; /* detect recursion */ - unsigned int disable_delay; /* disable delay in msecs */ - struct delayed_work disable; /* disabling work */ struct mmc_card *card; /* device attached to this host */ @@ -407,17 +380,8 @@ int mmc_card_awake(struct mmc_host *host); int mmc_card_sleep(struct mmc_host *host); int mmc_card_can_sleep(struct mmc_host *host); -int mmc_host_enable(struct mmc_host *host); -int mmc_host_disable(struct mmc_host *host); -int mmc_host_lazy_disable(struct mmc_host *host); int mmc_pm_notify(struct notifier_block *notify_block, unsigned long, void *); -static inline void mmc_set_disable_delay(struct mmc_host *host, - unsigned int disable_delay) -{ - host->disable_delay = disable_delay; -} - /* Module parameter */ extern bool mmc_assume_removable; diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h index fb9f6e116e1..b822a2cb600 100644 --- a/include/linux/mmc/mmc.h +++ b/include/linux/mmc/mmc.h @@ -274,6 +274,7 @@ struct _mmc_csd { #define EXT_CSD_FLUSH_CACHE 32 /* W */ #define EXT_CSD_CACHE_CTRL 33 /* R/W */ #define EXT_CSD_POWER_OFF_NOTIFICATION 34 /* R/W */ +#define EXT_CSD_DATA_SECTOR_SIZE 61 /* R */ #define EXT_CSD_GP_SIZE_MULT 143 /* R/W */ #define EXT_CSD_PARTITION_ATTRIBUTE 156 /* R/W */ #define EXT_CSD_PARTITION_SUPPORT 160 /* RO */ @@ -315,6 +316,8 @@ struct _mmc_csd { #define EXT_CSD_POWER_OFF_LONG_TIME 247 /* RO */ #define EXT_CSD_GENERIC_CMD6_TIME 248 /* RO */ #define EXT_CSD_CACHE_SIZE 249 /* RO, 4 bytes */ +#define EXT_CSD_TAG_UNIT_SIZE 498 /* RO */ +#define EXT_CSD_DATA_TAG_SUPPORT 499 /* RO */ #define EXT_CSD_HPI_FEATURES 503 /* RO */ /* diff --git a/include/linux/mmc/sdhci.h b/include/linux/mmc/sdhci.h index c750f85177d..e9051e1cb1c 100644 --- a/include/linux/mmc/sdhci.h +++ b/include/linux/mmc/sdhci.h @@ -90,6 +90,8 @@ struct sdhci_host { unsigned int quirks2; /* More deviations from spec. */ +#define SDHCI_QUIRK2_HOST_OFF_CARD_ON (1<<0) + int irq; /* Device IRQ */ void __iomem *ioaddr; /* Mapped address */ diff --git a/include/linux/mmc/sh_mmcif.h b/include/linux/mmc/sh_mmcif.h index 04ff452bf5c..05f0e3db1c1 100644 --- a/include/linux/mmc/sh_mmcif.h +++ b/include/linux/mmc/sh_mmcif.h @@ -77,18 +77,15 @@ struct sh_mmcif_plat_data { /* CE_CLK_CTRL */ #define CLK_ENABLE (1 << 24) /* 1: output mmc clock */ -#define CLK_CLEAR ((1 << 19) | (1 << 18) | (1 << 17) | (1 << 16)) -#define CLK_SUP_PCLK ((1 << 19) | (1 << 18) | (1 << 17) | (1 << 16)) -#define CLKDIV_4 (1<<16) /* mmc clock frequency. - * n: bus clock/(2^(n+1)) */ -#define CLKDIV_256 (7<<16) /* mmc clock frequency. (see above) */ -#define SRSPTO_256 ((1 << 13) | (0 << 12)) /* resp timeout */ -#define SRBSYTO_29 ((1 << 11) | (1 << 10) | \ - (1 << 9) | (1 << 8)) /* resp busy timeout */ -#define SRWDTO_29 ((1 << 7) | (1 << 6) | \ - (1 << 5) | (1 << 4)) /* read/write timeout */ -#define SCCSTO_29 ((1 << 3) | (1 << 2) | \ - (1 << 1) | (1 << 0)) /* ccs timeout */ +#define CLK_CLEAR (0xf << 16) +#define CLK_SUP_PCLK (0xf << 16) +#define CLKDIV_4 (1 << 16) /* mmc clock frequency. + * n: bus clock/(2^(n+1)) */ +#define CLKDIV_256 (7 << 16) /* mmc clock frequency. (see above) */ +#define SRSPTO_256 (2 << 12) /* resp timeout */ +#define SRBSYTO_29 (0xf << 8) /* resp busy timeout */ +#define SRWDTO_29 (0xf << 4) /* read/write timeout */ +#define SCCSTO_29 (0xf << 0) /* ccs timeout */ /* CE_VERSION */ #define SOFT_RST_ON (1 << 31) diff --git a/include/linux/mmc/sh_mobile_sdhi.h b/include/linux/mmc/sh_mobile_sdhi.h index 71b805451bd..e94e620aedd 100644 --- a/include/linux/mmc/sh_mobile_sdhi.h +++ b/include/linux/mmc/sh_mobile_sdhi.h @@ -10,15 +10,29 @@ struct tmio_mmc_data; #define SH_MOBILE_SDHI_IRQ_SDCARD "sdcard" #define SH_MOBILE_SDHI_IRQ_SDIO "sdio" +/** + * struct sh_mobile_sdhi_ops - SDHI driver callbacks + * @cd_wakeup: trigger a card-detection run + */ +struct sh_mobile_sdhi_ops { + void (*cd_wakeup)(const struct platform_device *pdev); +}; + struct sh_mobile_sdhi_info { int dma_slave_tx; int dma_slave_rx; unsigned long tmio_flags; unsigned long tmio_caps; u32 tmio_ocr_mask; /* available MMC voltages */ + unsigned int cd_gpio; struct tmio_mmc_data *pdata; void (*set_pwr)(struct platform_device *pdev, int state); int (*get_cd)(struct platform_device *pdev); + + /* callbacks for board specific setup code */ + int (*init)(struct platform_device *pdev, + const struct sh_mobile_sdhi_ops *ops); + void (*cleanup)(struct platform_device *pdev); }; #endif /* LINUX_MMC_SH_MOBILE_SDHI_H */ diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h index fb69ad191ad..501da4cb8a6 100644 --- a/include/linux/mod_devicetable.h +++ b/include/linux/mod_devicetable.h @@ -414,6 +414,15 @@ struct hv_vmbus_device_id { __attribute__((aligned(sizeof(kernel_ulong_t)))); }; +/* rpmsg */ + +#define RPMSG_NAME_SIZE 32 +#define RPMSG_DEVICE_MODALIAS_FMT "rpmsg:%s" + +struct rpmsg_device_id { + char name[RPMSG_NAME_SIZE]; +}; + /* i2c */ #define I2C_NAME_SIZE 20 diff --git a/include/linux/module.h b/include/linux/module.h index 4598bf03e98..fbcafe2ee13 100644 --- a/include/linux/module.h +++ b/include/linux/module.h @@ -21,8 +21,6 @@ #include <linux/percpu.h> #include <asm/module.h> -#include <trace/events/module.h> - /* Not Yet Implemented */ #define MODULE_SUPPORTED_DEVICE(name) @@ -452,33 +450,11 @@ void symbol_put_addr(void *addr); /* Sometimes we know we already have a refcount, and it's easier not to handle the error case (which only happens with rmmod --wait). */ -static inline void __module_get(struct module *module) -{ - if (module) { - preempt_disable(); - __this_cpu_inc(module->refptr->incs); - trace_module_get(module, _THIS_IP_); - preempt_enable(); - } -} - -static inline int try_module_get(struct module *module) -{ - int ret = 1; - - if (module) { - preempt_disable(); +extern void __module_get(struct module *module); - if (likely(module_is_live(module))) { - __this_cpu_inc(module->refptr->incs); - trace_module_get(module, _THIS_IP_); - } else - ret = 0; - - preempt_enable(); - } - return ret; -} +/* This is the Right Way to get a module: if it fails, it's being removed, + * so pretend it's not there. */ +extern bool try_module_get(struct module *module); extern void module_put(struct module *module); diff --git a/include/linux/moduleparam.h b/include/linux/moduleparam.h index c47f4d60db0..ea36486378d 100644 --- a/include/linux/moduleparam.h +++ b/include/linux/moduleparam.h @@ -47,14 +47,11 @@ struct kernel_param_ops { void (*free)(void *arg); }; -/* Flag bits for kernel_param.flags */ -#define KPARAM_ISBOOL 2 - struct kernel_param { const char *name; const struct kernel_param_ops *ops; u16 perm; - u16 flags; + s16 level; union { void *arg; const struct kparam_string *str; @@ -131,8 +128,40 @@ struct kparam_array * The ops can have NULL set or get functions. */ #define module_param_cb(name, ops, arg, perm) \ - __module_param_call(MODULE_PARAM_PREFIX, \ - name, ops, arg, __same_type((arg), bool *), perm) + __module_param_call(MODULE_PARAM_PREFIX, name, ops, arg, perm, 0) + +/** + * <level>_param_cb - general callback for a module/cmdline parameter + * to be evaluated before certain initcall level + * @name: a valid C identifier which is the parameter name. + * @ops: the set & get operations for this parameter. + * @perm: visibility in sysfs. + * + * The ops can have NULL set or get functions. + */ +#define __level_param_cb(name, ops, arg, perm, level) \ + __module_param_call(MODULE_PARAM_PREFIX, name, ops, arg, perm, level) + +#define core_param_cb(name, ops, arg, perm) \ + __level_param_cb(name, ops, arg, perm, 1) + +#define postcore_param_cb(name, ops, arg, perm) \ + __level_param_cb(name, ops, arg, perm, 2) + +#define arch_param_cb(name, ops, arg, perm) \ + __level_param_cb(name, ops, arg, perm, 3) + +#define subsys_param_cb(name, ops, arg, perm) \ + __level_param_cb(name, ops, arg, perm, 4) + +#define fs_param_cb(name, ops, arg, perm) \ + __level_param_cb(name, ops, arg, perm, 5) + +#define device_param_cb(name, ops, arg, perm) \ + __level_param_cb(name, ops, arg, perm, 6) + +#define late_param_cb(name, ops, arg, perm) \ + __level_param_cb(name, ops, arg, perm, 7) /* On alpha, ia64 and ppc64 relocations to global data cannot go into read-only sections (which is part of respective UNIX ABI on these @@ -146,7 +175,7 @@ struct kparam_array /* This is the fundamental function for registering boot/module parameters. */ -#define __module_param_call(prefix, name, ops, arg, isbool, perm) \ +#define __module_param_call(prefix, name, ops, arg, perm, level) \ /* Default value instead of permissions? */ \ static int __param_perm_check_##name __attribute__((unused)) = \ BUILD_BUG_ON_ZERO((perm) < 0 || (perm) > 0777 || ((perm) & 2)) \ @@ -155,8 +184,7 @@ struct kparam_array static struct kernel_param __moduleparam_const __param_##name \ __used \ __attribute__ ((unused,__section__ ("__param"),aligned(sizeof(void *)))) \ - = { __param_str_##name, ops, perm, isbool ? KPARAM_ISBOOL : 0, \ - { arg } } + = { __param_str_##name, ops, perm, level, { arg } } /* Obsolete - use module_param_cb() */ #define module_param_call(name, set, get, arg, perm) \ @@ -164,8 +192,7 @@ struct kparam_array { (void *)set, (void *)get }; \ __module_param_call(MODULE_PARAM_PREFIX, \ name, &__param_ops_##name, arg, \ - __same_type(arg, bool *), \ - (perm) + sizeof(__check_old_set_param(set))*0) + (perm) + sizeof(__check_old_set_param(set))*0, 0) /* We don't get oldget: it's often a new-style param_get_uint, etc. */ static inline int @@ -245,8 +272,7 @@ static inline void __kernel_param_unlock(void) */ #define core_param(name, var, type, perm) \ param_check_##type(name, &(var)); \ - __module_param_call("", name, ¶m_ops_##type, \ - &var, __same_type(var, bool), perm) + __module_param_call("", name, ¶m_ops_##type, &var, perm, 0) #endif /* !MODULE */ /** @@ -264,7 +290,7 @@ static inline void __kernel_param_unlock(void) = { len, string }; \ __module_param_call(MODULE_PARAM_PREFIX, name, \ ¶m_ops_string, \ - .str = &__param_string_##name, 0, perm); \ + .str = &__param_string_##name, perm, 0); \ __MODULE_PARM_TYPE(name, "string") /** @@ -292,6 +318,8 @@ extern int parse_args(const char *name, char *args, const struct kernel_param *params, unsigned num, + s16 level_min, + s16 level_max, int (*unknown)(char *param, char *val)); /* Called by module remove. */ @@ -403,7 +431,7 @@ extern int param_set_bint(const char *val, const struct kernel_param *kp); __module_param_call(MODULE_PARAM_PREFIX, name, \ ¶m_array_ops, \ .arr = &__param_arr_##name, \ - __same_type(array[0], bool), perm); \ + perm, 0); \ __MODULE_PARM_TYPE(name, "array of " #type) extern struct kernel_param_ops param_array_ops; diff --git a/include/linux/mtd/bbm.h b/include/linux/mtd/bbm.h index c4eec228eef..650ef352f04 100644 --- a/include/linux/mtd/bbm.h +++ b/include/linux/mtd/bbm.h @@ -112,6 +112,11 @@ struct nand_bbt_descr { #define NAND_BBT_USE_FLASH 0x00020000 /* Do not store flash based bad block table in OOB area; store it in-band */ #define NAND_BBT_NO_OOB 0x00040000 +/* + * Do not write new bad block markers to OOB; useful, e.g., when ECC covers + * entire spare area. Must be used with NAND_BBT_USE_FLASH. + */ +#define NAND_BBT_NO_OOB_BBM 0x00080000 /* * Flag set by nand_create_default_bbt_descr(), marking that the nand_bbt_descr diff --git a/include/linux/mtd/blktrans.h b/include/linux/mtd/blktrans.h index 1bbd9f28924..ed270bd2e4d 100644 --- a/include/linux/mtd/blktrans.h +++ b/include/linux/mtd/blktrans.h @@ -47,6 +47,7 @@ struct mtd_blktrans_dev { struct request_queue *rq; spinlock_t queue_lock; void *priv; + fmode_t file_mode; }; struct mtd_blktrans_ops { diff --git a/include/linux/mtd/fsmc.h b/include/linux/mtd/fsmc.h index 6987995ad3c..b20029221fb 100644 --- a/include/linux/mtd/fsmc.h +++ b/include/linux/mtd/fsmc.h @@ -26,95 +26,83 @@ #define FSMC_NAND_BW8 1 #define FSMC_NAND_BW16 2 -/* - * The placement of the Command Latch Enable (CLE) and - * Address Latch Enable (ALE) is twisted around in the - * SPEAR310 implementation. - */ -#if defined(CONFIG_MACH_SPEAR310) -#define PLAT_NAND_CLE (1 << 17) -#define PLAT_NAND_ALE (1 << 16) -#else -#define PLAT_NAND_CLE (1 << 16) -#define PLAT_NAND_ALE (1 << 17) -#endif - #define FSMC_MAX_NOR_BANKS 4 #define FSMC_MAX_NAND_BANKS 4 #define FSMC_FLASH_WIDTH8 1 #define FSMC_FLASH_WIDTH16 2 -struct fsmc_nor_bank_regs { - uint32_t ctrl; - uint32_t ctrl_tim; -}; - -/* ctrl register definitions */ -#define BANK_ENABLE (1 << 0) -#define MUXED (1 << 1) -#define NOR_DEV (2 << 2) -#define WIDTH_8 (0 << 4) -#define WIDTH_16 (1 << 4) -#define RSTPWRDWN (1 << 6) -#define WPROT (1 << 7) -#define WRT_ENABLE (1 << 12) -#define WAIT_ENB (1 << 13) - -/* ctrl_tim register definitions */ - -struct fsmc_nand_bank_regs { - uint32_t pc; - uint32_t sts; - uint32_t comm; - uint32_t attrib; - uint32_t ioata; - uint32_t ecc1; - uint32_t ecc2; - uint32_t ecc3; -}; - +/* fsmc controller registers for NOR flash */ +#define CTRL 0x0 + /* ctrl register definitions */ + #define BANK_ENABLE (1 << 0) + #define MUXED (1 << 1) + #define NOR_DEV (2 << 2) + #define WIDTH_8 (0 << 4) + #define WIDTH_16 (1 << 4) + #define RSTPWRDWN (1 << 6) + #define WPROT (1 << 7) + #define WRT_ENABLE (1 << 12) + #define WAIT_ENB (1 << 13) + +#define CTRL_TIM 0x4 + /* ctrl_tim register definitions */ + +#define FSMC_NOR_BANK_SZ 0x8 #define FSMC_NOR_REG_SIZE 0x40 -struct fsmc_regs { - struct fsmc_nor_bank_regs nor_bank_regs[FSMC_MAX_NOR_BANKS]; - uint8_t reserved_1[0x40 - 0x20]; - struct fsmc_nand_bank_regs bank_regs[FSMC_MAX_NAND_BANKS]; - uint8_t reserved_2[0xfe0 - 0xc0]; - uint32_t peripid0; /* 0xfe0 */ - uint32_t peripid1; /* 0xfe4 */ - uint32_t peripid2; /* 0xfe8 */ - uint32_t peripid3; /* 0xfec */ - uint32_t pcellid0; /* 0xff0 */ - uint32_t pcellid1; /* 0xff4 */ - uint32_t pcellid2; /* 0xff8 */ - uint32_t pcellid3; /* 0xffc */ -}; +#define FSMC_NOR_REG(base, bank, reg) (base + \ + FSMC_NOR_BANK_SZ * (bank) + \ + reg) + +/* fsmc controller registers for NAND flash */ +#define PC 0x00 + /* pc register definitions */ + #define FSMC_RESET (1 << 0) + #define FSMC_WAITON (1 << 1) + #define FSMC_ENABLE (1 << 2) + #define FSMC_DEVTYPE_NAND (1 << 3) + #define FSMC_DEVWID_8 (0 << 4) + #define FSMC_DEVWID_16 (1 << 4) + #define FSMC_ECCEN (1 << 6) + #define FSMC_ECCPLEN_512 (0 << 7) + #define FSMC_ECCPLEN_256 (1 << 7) + #define FSMC_TCLR_1 (1) + #define FSMC_TCLR_SHIFT (9) + #define FSMC_TCLR_MASK (0xF) + #define FSMC_TAR_1 (1) + #define FSMC_TAR_SHIFT (13) + #define FSMC_TAR_MASK (0xF) +#define STS 0x04 + /* sts register definitions */ + #define FSMC_CODE_RDY (1 << 15) +#define COMM 0x08 + /* comm register definitions */ + #define FSMC_TSET_0 0 + #define FSMC_TSET_SHIFT 0 + #define FSMC_TSET_MASK 0xFF + #define FSMC_TWAIT_6 6 + #define FSMC_TWAIT_SHIFT 8 + #define FSMC_TWAIT_MASK 0xFF + #define FSMC_THOLD_4 4 + #define FSMC_THOLD_SHIFT 16 + #define FSMC_THOLD_MASK 0xFF + #define FSMC_THIZ_1 1 + #define FSMC_THIZ_SHIFT 24 + #define FSMC_THIZ_MASK 0xFF +#define ATTRIB 0x0C +#define IOATA 0x10 +#define ECC1 0x14 +#define ECC2 0x18 +#define ECC3 0x1C +#define FSMC_NAND_BANK_SZ 0x20 + +#define FSMC_NAND_REG(base, bank, reg) (base + FSMC_NOR_REG_SIZE + \ + (FSMC_NAND_BANK_SZ * (bank)) + \ + reg) #define FSMC_BUSY_WAIT_TIMEOUT (1 * HZ) -/* pc register definitions */ -#define FSMC_RESET (1 << 0) -#define FSMC_WAITON (1 << 1) -#define FSMC_ENABLE (1 << 2) -#define FSMC_DEVTYPE_NAND (1 << 3) -#define FSMC_DEVWID_8 (0 << 4) -#define FSMC_DEVWID_16 (1 << 4) -#define FSMC_ECCEN (1 << 6) -#define FSMC_ECCPLEN_512 (0 << 7) -#define FSMC_ECCPLEN_256 (1 << 7) -#define FSMC_TCLR_1 (1 << 9) -#define FSMC_TAR_1 (1 << 13) - -/* sts register definitions */ -#define FSMC_CODE_RDY (1 << 15) - -/* comm register definitions */ -#define FSMC_TSET_0 (0 << 0) -#define FSMC_TWAIT_6 (6 << 8) -#define FSMC_THOLD_4 (4 << 16) -#define FSMC_THIZ_1 (1 << 24) - /* * There are 13 bytes of ecc for every 512 byte block in FSMC version 8 * and it has to be read consecutively and immediately after the 512 @@ -133,6 +121,20 @@ struct fsmc_eccplace { struct fsmc_nand_eccplace eccplace[MAX_ECCPLACE_ENTRIES]; }; +struct fsmc_nand_timings { + uint8_t tclr; + uint8_t tar; + uint8_t thiz; + uint8_t thold; + uint8_t twait; + uint8_t tset; +}; + +enum access_mode { + USE_DMA_ACCESS = 1, + USE_WORD_ACCESS, +}; + /** * fsmc_nand_platform_data - platform specific NAND controller config * @partitions: partition table for the platform, use a default fallback @@ -146,12 +148,23 @@ struct fsmc_eccplace { * this may be set to NULL */ struct fsmc_nand_platform_data { + struct fsmc_nand_timings *nand_timings; struct mtd_partition *partitions; unsigned int nr_partitions; unsigned int options; unsigned int width; unsigned int bank; + + /* CLE, ALE offsets */ + unsigned int cle_off; + unsigned int ale_off; + enum access_mode mode; + void (*select_bank)(uint32_t bank, uint32_t busw); + + /* priv structures for dma accesses */ + void *read_dma_priv; + void *write_dma_priv; }; extern int __init fsmc_nor_init(struct platform_device *pdev, diff --git a/include/linux/mtd/map.h b/include/linux/mtd/map.h index 94e924e2ecd..3595a0236b0 100644 --- a/include/linux/mtd/map.h +++ b/include/linux/mtd/map.h @@ -29,8 +29,8 @@ #include <linux/kernel.h> #include <asm/unaligned.h> -#include <asm/system.h> #include <asm/io.h> +#include <asm/barrier.h> #ifdef CONFIG_MTD_MAP_BANK_WIDTH_1 #define map_bankwidth(map) 1 diff --git a/include/linux/mtd/mtd.h b/include/linux/mtd/mtd.h index d43dc25af82..cf5ea8cdcf8 100644 --- a/include/linux/mtd/mtd.h +++ b/include/linux/mtd/mtd.h @@ -164,6 +164,9 @@ struct mtd_info { /* ECC layout structure pointer - read only! */ struct nand_ecclayout *ecclayout; + /* max number of correctible bit errors per writesize */ + unsigned int ecc_strength; + /* Data for variable erase regions. If numeraseregions is zero, * it means that the whole device has erasesize as given above. */ @@ -174,52 +177,52 @@ struct mtd_info { * Do not call via these pointers, use corresponding mtd_*() * wrappers instead. */ - int (*erase) (struct mtd_info *mtd, struct erase_info *instr); - int (*point) (struct mtd_info *mtd, loff_t from, size_t len, - size_t *retlen, void **virt, resource_size_t *phys); - void (*unpoint) (struct mtd_info *mtd, loff_t from, size_t len); - unsigned long (*get_unmapped_area) (struct mtd_info *mtd, - unsigned long len, - unsigned long offset, - unsigned long flags); - int (*read) (struct mtd_info *mtd, loff_t from, size_t len, - size_t *retlen, u_char *buf); - int (*write) (struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, const u_char *buf); - int (*panic_write) (struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, const u_char *buf); - int (*read_oob) (struct mtd_info *mtd, loff_t from, - struct mtd_oob_ops *ops); - int (*write_oob) (struct mtd_info *mtd, loff_t to, + int (*_erase) (struct mtd_info *mtd, struct erase_info *instr); + int (*_point) (struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, void **virt, resource_size_t *phys); + int (*_unpoint) (struct mtd_info *mtd, loff_t from, size_t len); + unsigned long (*_get_unmapped_area) (struct mtd_info *mtd, + unsigned long len, + unsigned long offset, + unsigned long flags); + int (*_read) (struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, u_char *buf); + int (*_write) (struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const u_char *buf); + int (*_panic_write) (struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const u_char *buf); + int (*_read_oob) (struct mtd_info *mtd, loff_t from, struct mtd_oob_ops *ops); - int (*get_fact_prot_info) (struct mtd_info *mtd, struct otp_info *buf, - size_t len); - int (*read_fact_prot_reg) (struct mtd_info *mtd, loff_t from, - size_t len, size_t *retlen, u_char *buf); - int (*get_user_prot_info) (struct mtd_info *mtd, struct otp_info *buf, - size_t len); - int (*read_user_prot_reg) (struct mtd_info *mtd, loff_t from, - size_t len, size_t *retlen, u_char *buf); - int (*write_user_prot_reg) (struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, u_char *buf); - int (*lock_user_prot_reg) (struct mtd_info *mtd, loff_t from, - size_t len); - int (*writev) (struct mtd_info *mtd, const struct kvec *vecs, + int (*_write_oob) (struct mtd_info *mtd, loff_t to, + struct mtd_oob_ops *ops); + int (*_get_fact_prot_info) (struct mtd_info *mtd, struct otp_info *buf, + size_t len); + int (*_read_fact_prot_reg) (struct mtd_info *mtd, loff_t from, + size_t len, size_t *retlen, u_char *buf); + int (*_get_user_prot_info) (struct mtd_info *mtd, struct otp_info *buf, + size_t len); + int (*_read_user_prot_reg) (struct mtd_info *mtd, loff_t from, + size_t len, size_t *retlen, u_char *buf); + int (*_write_user_prot_reg) (struct mtd_info *mtd, loff_t to, + size_t len, size_t *retlen, u_char *buf); + int (*_lock_user_prot_reg) (struct mtd_info *mtd, loff_t from, + size_t len); + int (*_writev) (struct mtd_info *mtd, const struct kvec *vecs, unsigned long count, loff_t to, size_t *retlen); - void (*sync) (struct mtd_info *mtd); - int (*lock) (struct mtd_info *mtd, loff_t ofs, uint64_t len); - int (*unlock) (struct mtd_info *mtd, loff_t ofs, uint64_t len); - int (*is_locked) (struct mtd_info *mtd, loff_t ofs, uint64_t len); - int (*block_isbad) (struct mtd_info *mtd, loff_t ofs); - int (*block_markbad) (struct mtd_info *mtd, loff_t ofs); - int (*suspend) (struct mtd_info *mtd); - void (*resume) (struct mtd_info *mtd); + void (*_sync) (struct mtd_info *mtd); + int (*_lock) (struct mtd_info *mtd, loff_t ofs, uint64_t len); + int (*_unlock) (struct mtd_info *mtd, loff_t ofs, uint64_t len); + int (*_is_locked) (struct mtd_info *mtd, loff_t ofs, uint64_t len); + int (*_block_isbad) (struct mtd_info *mtd, loff_t ofs); + int (*_block_markbad) (struct mtd_info *mtd, loff_t ofs); + int (*_suspend) (struct mtd_info *mtd); + void (*_resume) (struct mtd_info *mtd); /* * If the driver is something smart, like UBI, it may need to maintain * its own reference counting. The below functions are only for driver. */ - int (*get_device) (struct mtd_info *mtd); - void (*put_device) (struct mtd_info *mtd); + int (*_get_device) (struct mtd_info *mtd); + void (*_put_device) (struct mtd_info *mtd); /* Backing device capabilities for this device * - provides mmap capabilities @@ -240,214 +243,75 @@ struct mtd_info { int usecount; }; -/* - * Erase is an asynchronous operation. Device drivers are supposed - * to call instr->callback() whenever the operation completes, even - * if it completes with a failure. - * Callers are supposed to pass a callback function and wait for it - * to be called before writing to the block. - */ -static inline int mtd_erase(struct mtd_info *mtd, struct erase_info *instr) -{ - return mtd->erase(mtd, instr); -} - -/* - * This stuff for eXecute-In-Place. phys is optional and may be set to NULL. - */ -static inline int mtd_point(struct mtd_info *mtd, loff_t from, size_t len, - size_t *retlen, void **virt, resource_size_t *phys) -{ - *retlen = 0; - if (!mtd->point) - return -EOPNOTSUPP; - return mtd->point(mtd, from, len, retlen, virt, phys); -} - -/* We probably shouldn't allow XIP if the unpoint isn't a NULL */ -static inline void mtd_unpoint(struct mtd_info *mtd, loff_t from, size_t len) -{ - return mtd->unpoint(mtd, from, len); -} - -/* - * Allow NOMMU mmap() to directly map the device (if not NULL) - * - return the address to which the offset maps - * - return -ENOSYS to indicate refusal to do the mapping - */ -static inline unsigned long mtd_get_unmapped_area(struct mtd_info *mtd, - unsigned long len, - unsigned long offset, - unsigned long flags) -{ - if (!mtd->get_unmapped_area) - return -EOPNOTSUPP; - return mtd->get_unmapped_area(mtd, len, offset, flags); -} - -static inline int mtd_read(struct mtd_info *mtd, loff_t from, size_t len, - size_t *retlen, u_char *buf) -{ - return mtd->read(mtd, from, len, retlen, buf); -} - -static inline int mtd_write(struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, const u_char *buf) -{ - *retlen = 0; - if (!mtd->write) - return -EROFS; - return mtd->write(mtd, to, len, retlen, buf); -} - -/* - * In blackbox flight recorder like scenarios we want to make successful writes - * in interrupt context. panic_write() is only intended to be called when its - * known the kernel is about to panic and we need the write to succeed. Since - * the kernel is not going to be running for much longer, this function can - * break locks and delay to ensure the write succeeds (but not sleep). - */ -static inline int mtd_panic_write(struct mtd_info *mtd, loff_t to, size_t len, - size_t *retlen, const u_char *buf) -{ - *retlen = 0; - if (!mtd->panic_write) - return -EOPNOTSUPP; - return mtd->panic_write(mtd, to, len, retlen, buf); -} +int mtd_erase(struct mtd_info *mtd, struct erase_info *instr); +int mtd_point(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, + void **virt, resource_size_t *phys); +int mtd_unpoint(struct mtd_info *mtd, loff_t from, size_t len); +unsigned long mtd_get_unmapped_area(struct mtd_info *mtd, unsigned long len, + unsigned long offset, unsigned long flags); +int mtd_read(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, + u_char *buf); +int mtd_write(struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen, + const u_char *buf); +int mtd_panic_write(struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen, + const u_char *buf); static inline int mtd_read_oob(struct mtd_info *mtd, loff_t from, struct mtd_oob_ops *ops) { ops->retlen = ops->oobretlen = 0; - if (!mtd->read_oob) + if (!mtd->_read_oob) return -EOPNOTSUPP; - return mtd->read_oob(mtd, from, ops); + return mtd->_read_oob(mtd, from, ops); } static inline int mtd_write_oob(struct mtd_info *mtd, loff_t to, struct mtd_oob_ops *ops) { ops->retlen = ops->oobretlen = 0; - if (!mtd->write_oob) - return -EOPNOTSUPP; - return mtd->write_oob(mtd, to, ops); -} - -/* - * Method to access the protection register area, present in some flash - * devices. The user data is one time programmable but the factory data is read - * only. - */ -static inline int mtd_get_fact_prot_info(struct mtd_info *mtd, - struct otp_info *buf, size_t len) -{ - if (!mtd->get_fact_prot_info) + if (!mtd->_write_oob) return -EOPNOTSUPP; - return mtd->get_fact_prot_info(mtd, buf, len); -} - -static inline int mtd_read_fact_prot_reg(struct mtd_info *mtd, loff_t from, - size_t len, size_t *retlen, - u_char *buf) -{ - *retlen = 0; - if (!mtd->read_fact_prot_reg) - return -EOPNOTSUPP; - return mtd->read_fact_prot_reg(mtd, from, len, retlen, buf); -} - -static inline int mtd_get_user_prot_info(struct mtd_info *mtd, - struct otp_info *buf, - size_t len) -{ - if (!mtd->get_user_prot_info) - return -EOPNOTSUPP; - return mtd->get_user_prot_info(mtd, buf, len); -} - -static inline int mtd_read_user_prot_reg(struct mtd_info *mtd, loff_t from, - size_t len, size_t *retlen, - u_char *buf) -{ - *retlen = 0; - if (!mtd->read_user_prot_reg) - return -EOPNOTSUPP; - return mtd->read_user_prot_reg(mtd, from, len, retlen, buf); -} - -static inline int mtd_write_user_prot_reg(struct mtd_info *mtd, loff_t to, - size_t len, size_t *retlen, - u_char *buf) -{ - *retlen = 0; - if (!mtd->write_user_prot_reg) - return -EOPNOTSUPP; - return mtd->write_user_prot_reg(mtd, to, len, retlen, buf); + if (!(mtd->flags & MTD_WRITEABLE)) + return -EROFS; + return mtd->_write_oob(mtd, to, ops); } -static inline int mtd_lock_user_prot_reg(struct mtd_info *mtd, loff_t from, - size_t len) -{ - if (!mtd->lock_user_prot_reg) - return -EOPNOTSUPP; - return mtd->lock_user_prot_reg(mtd, from, len); -} +int mtd_get_fact_prot_info(struct mtd_info *mtd, struct otp_info *buf, + size_t len); +int mtd_read_fact_prot_reg(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, u_char *buf); +int mtd_get_user_prot_info(struct mtd_info *mtd, struct otp_info *buf, + size_t len); +int mtd_read_user_prot_reg(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, u_char *buf); +int mtd_write_user_prot_reg(struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, u_char *buf); +int mtd_lock_user_prot_reg(struct mtd_info *mtd, loff_t from, size_t len); int mtd_writev(struct mtd_info *mtd, const struct kvec *vecs, unsigned long count, loff_t to, size_t *retlen); static inline void mtd_sync(struct mtd_info *mtd) { - if (mtd->sync) - mtd->sync(mtd); -} - -/* Chip-supported device locking */ -static inline int mtd_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len) -{ - if (!mtd->lock) - return -EOPNOTSUPP; - return mtd->lock(mtd, ofs, len); + if (mtd->_sync) + mtd->_sync(mtd); } -static inline int mtd_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len) -{ - if (!mtd->unlock) - return -EOPNOTSUPP; - return mtd->unlock(mtd, ofs, len); -} - -static inline int mtd_is_locked(struct mtd_info *mtd, loff_t ofs, uint64_t len) -{ - if (!mtd->is_locked) - return -EOPNOTSUPP; - return mtd->is_locked(mtd, ofs, len); -} +int mtd_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len); +int mtd_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len); +int mtd_is_locked(struct mtd_info *mtd, loff_t ofs, uint64_t len); +int mtd_block_isbad(struct mtd_info *mtd, loff_t ofs); +int mtd_block_markbad(struct mtd_info *mtd, loff_t ofs); static inline int mtd_suspend(struct mtd_info *mtd) { - return mtd->suspend ? mtd->suspend(mtd) : 0; + return mtd->_suspend ? mtd->_suspend(mtd) : 0; } static inline void mtd_resume(struct mtd_info *mtd) { - if (mtd->resume) - mtd->resume(mtd); -} - -static inline int mtd_block_isbad(struct mtd_info *mtd, loff_t ofs) -{ - if (!mtd->block_isbad) - return 0; - return mtd->block_isbad(mtd, ofs); -} - -static inline int mtd_block_markbad(struct mtd_info *mtd, loff_t ofs) -{ - if (!mtd->block_markbad) - return -EOPNOTSUPP; - return mtd->block_markbad(mtd, ofs); + if (mtd->_resume) + mtd->_resume(mtd); } static inline uint32_t mtd_div_by_eb(uint64_t sz, struct mtd_info *mtd) @@ -482,12 +346,12 @@ static inline uint32_t mtd_mod_by_ws(uint64_t sz, struct mtd_info *mtd) static inline int mtd_has_oob(const struct mtd_info *mtd) { - return mtd->read_oob && mtd->write_oob; + return mtd->_read_oob && mtd->_write_oob; } static inline int mtd_can_have_bb(const struct mtd_info *mtd) { - return !!mtd->block_isbad; + return !!mtd->_block_isbad; } /* Kernel-side ioctl definitions */ diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h index 63b5a8b6dfb..1482340d3d9 100644 --- a/include/linux/mtd/nand.h +++ b/include/linux/mtd/nand.h @@ -324,6 +324,7 @@ struct nand_hw_control { * @steps: number of ECC steps per page * @size: data bytes per ECC step * @bytes: ECC bytes per step + * @strength: max number of correctible bits per ECC step * @total: total number of ECC bytes per page * @prepad: padding information for syndrome based ECC generators * @postpad: padding information for syndrome based ECC generators @@ -351,6 +352,7 @@ struct nand_ecc_ctrl { int size; int bytes; int total; + int strength; int prepad; int postpad; struct nand_ecclayout *layout; @@ -448,8 +450,9 @@ struct nand_buffers { * will be copied to the appropriate nand_bbt_descr's. * @badblockpos: [INTERN] position of the bad block marker in the oob * area. - * @badblockbits: [INTERN] number of bits to left-shift the bad block - * number + * @badblockbits: [INTERN] minimum number of set bits in a good block's + * bad block marker position; i.e., BBM == 11110111b is + * not bad when badblockbits == 7 * @cellinfo: [INTERN] MLC/multichip data from chip ident * @numchips: [INTERN] number of physical chips * @chipsize: [INTERN] the size of one chip for multichip arrays diff --git a/include/linux/mtd/pmc551.h b/include/linux/mtd/pmc551.h deleted file mode 100644 index 27ad40aed19..00000000000 --- a/include/linux/mtd/pmc551.h +++ /dev/null @@ -1,78 +0,0 @@ -/* - * PMC551 PCI Mezzanine Ram Device - * - * Author: - * Mark Ferrell - * Copyright 1999,2000 Nortel Networks - * - * License: - * As part of this driver was derrived from the slram.c driver it falls - * under the same license, which is GNU General Public License v2 - */ - -#ifndef __MTD_PMC551_H__ -#define __MTD_PMC551_H__ - -#include <linux/mtd/mtd.h> - -#define PMC551_VERSION \ - "Ramix PMC551 PCI Mezzanine Ram Driver. (C) 1999,2000 Nortel Networks.\n" - -/* - * Our personal and private information - */ -struct mypriv { - struct pci_dev *dev; - u_char *start; - u32 base_map0; - u32 curr_map0; - u32 asize; - struct mtd_info *nextpmc551; -}; - -/* - * Function Prototypes - */ -static int pmc551_erase(struct mtd_info *, struct erase_info *); -static void pmc551_unpoint(struct mtd_info *, loff_t, size_t); -static int pmc551_point(struct mtd_info *mtd, loff_t from, size_t len, - size_t *retlen, void **virt, resource_size_t *phys); -static int pmc551_read(struct mtd_info *, loff_t, size_t, size_t *, u_char *); -static int pmc551_write(struct mtd_info *, loff_t, size_t, size_t *, const u_char *); - - -/* - * Define the PCI ID's if the kernel doesn't define them for us - */ -#ifndef PCI_VENDOR_ID_V3_SEMI -#define PCI_VENDOR_ID_V3_SEMI 0x11b0 -#endif - -#ifndef PCI_DEVICE_ID_V3_SEMI_V370PDC -#define PCI_DEVICE_ID_V3_SEMI_V370PDC 0x0200 -#endif - - -#define PMC551_PCI_MEM_MAP0 0x50 -#define PMC551_PCI_MEM_MAP1 0x54 -#define PMC551_PCI_MEM_MAP_MAP_ADDR_MASK 0x3ff00000 -#define PMC551_PCI_MEM_MAP_APERTURE_MASK 0x000000f0 -#define PMC551_PCI_MEM_MAP_REG_EN 0x00000002 -#define PMC551_PCI_MEM_MAP_ENABLE 0x00000001 - -#define PMC551_SDRAM_MA 0x60 -#define PMC551_SDRAM_CMD 0x62 -#define PMC551_DRAM_CFG 0x64 -#define PMC551_SYS_CTRL_REG 0x78 - -#define PMC551_DRAM_BLK0 0x68 -#define PMC551_DRAM_BLK1 0x6c -#define PMC551_DRAM_BLK2 0x70 -#define PMC551_DRAM_BLK3 0x74 -#define PMC551_DRAM_BLK_GET_SIZE(x) (524288<<((x>>4)&0x0f)) -#define PMC551_DRAM_BLK_SET_COL_MUX(x,v) (((x) & ~0x00007000) | (((v) & 0x7) << 12)) -#define PMC551_DRAM_BLK_SET_ROW_MUX(x,v) (((x) & ~0x00000f00) | (((v) & 0xf) << 8)) - - -#endif /* __MTD_PMC551_H__ */ - diff --git a/include/linux/mtd/sh_flctl.h b/include/linux/mtd/sh_flctl.h index 9cf4c4c7955..a38e1fa8af0 100644 --- a/include/linux/mtd/sh_flctl.h +++ b/include/linux/mtd/sh_flctl.h @@ -23,6 +23,7 @@ #include <linux/mtd/mtd.h> #include <linux/mtd/nand.h> #include <linux/mtd/partitions.h> +#include <linux/pm_qos.h> /* FLCTL registers */ #define FLCMNCR(f) (f->reg + 0x0) @@ -38,6 +39,7 @@ #define FLDTFIFO(f) (f->reg + 0x24) #define FLECFIFO(f) (f->reg + 0x28) #define FLTRCR(f) (f->reg + 0x2C) +#define FLHOLDCR(f) (f->reg + 0x38) #define FL4ECCRESULT0(f) (f->reg + 0x80) #define FL4ECCRESULT1(f) (f->reg + 0x84) #define FL4ECCRESULT2(f) (f->reg + 0x88) @@ -67,6 +69,30 @@ #define CE0_ENABLE (0x1 << 3) /* Chip Enable 0 */ #define TYPESEL_SET (0x1 << 0) +/* + * Clock settings using the PULSEx registers from FLCMNCR + * + * Some hardware uses bits called PULSEx instead of FCKSEL_E and QTSEL_E + * to control the clock divider used between the High-Speed Peripheral Clock + * and the FLCTL internal clock. If so, use CLK_8_BIT_xxx for connecting 8 bit + * and CLK_16_BIT_xxx for connecting 16 bit bus bandwith NAND chips. For the 16 + * bit version the divider is seperate for the pulse width of high and low + * signals. + */ +#define PULSE3 (0x1 << 27) +#define PULSE2 (0x1 << 17) +#define PULSE1 (0x1 << 15) +#define PULSE0 (0x1 << 9) +#define CLK_8B_0_5 PULSE1 +#define CLK_8B_1 0x0 +#define CLK_8B_1_5 (PULSE1 | PULSE2) +#define CLK_8B_2 PULSE0 +#define CLK_8B_3 (PULSE0 | PULSE1 | PULSE2) +#define CLK_8B_4 (PULSE0 | PULSE2) +#define CLK_16B_6L_2H PULSE0 +#define CLK_16B_9L_3H (PULSE0 | PULSE1 | PULSE2) +#define CLK_16B_12L_4H (PULSE0 | PULSE2) + /* FLCMDCR control bits */ #define ADRCNT2_E (0x1 << 31) /* 5byte address enable */ #define ADRMD_E (0x1 << 26) /* Sector address access */ @@ -85,6 +111,15 @@ #define TRSTRT (0x1 << 0) /* translation start */ #define TREND (0x1 << 1) /* translation end */ +/* + * FLHOLDCR control bits + * + * HOLDEN: Bus Occupancy Enable (inverted) + * Enable this bit when the external bus might be used in between transfers. + * If not set and the bus gets used by other modules, a deadlock occurs. + */ +#define HOLDEN (0x1 << 0) + /* FL4ECCCR control bits */ #define _4ECCFA (0x1 << 2) /* 4 symbols correct fault */ #define _4ECCEND (0x1 << 1) /* 4 symbols end */ @@ -97,6 +132,7 @@ struct sh_flctl { struct mtd_info mtd; struct nand_chip chip; struct platform_device *pdev; + struct dev_pm_qos_request pm_qos; void __iomem *reg; uint8_t done_buff[2048 + 64]; /* max size 2048 + 64 */ @@ -108,11 +144,14 @@ struct sh_flctl { int erase1_page_addr; /* page_addr in ERASE1 cmd */ uint32_t erase_ADRCNT; /* bits of FLCMDCR in ERASE1 cmd */ uint32_t rw_ADRCNT; /* bits of FLCMDCR in READ WRITE cmd */ + uint32_t flcmncr_base; /* base value of FLCMNCR */ int hwecc_cant_correct[4]; unsigned page_size:1; /* NAND page size (0 = 512, 1 = 2048) */ unsigned hwecc:1; /* Hardware ECC (0 = disabled, 1 = enabled) */ + unsigned holden:1; /* Hardware has FLHOLDCR and HOLDEN is set */ + unsigned qos_request:1; /* QoS request to prevent deep power shutdown */ }; struct sh_flctl_platform_data { @@ -121,6 +160,7 @@ struct sh_flctl_platform_data { unsigned long flcmncr_val; unsigned has_hwecc:1; + unsigned use_holden:1; }; static inline struct sh_flctl *mtd_to_flctl(struct mtd_info *mtdinfo) diff --git a/include/linux/mtd/spear_smi.h b/include/linux/mtd/spear_smi.h new file mode 100644 index 00000000000..8ae1726044c --- /dev/null +++ b/include/linux/mtd/spear_smi.h @@ -0,0 +1,65 @@ +/* + * Copyright © 2010 ST Microelectronics + * Shiraz Hashim <shiraz.hashim@st.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#ifndef __MTD_SPEAR_SMI_H +#define __MTD_SPEAR_SMI_H + +#include <linux/types.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/platform_device.h> +#include <linux/of.h> + +/* max possible slots for serial-nor flash chip in the SMI controller */ +#define MAX_NUM_FLASH_CHIP 4 + +/* macro to define partitions for flash devices */ +#define DEFINE_PARTS(n, of, s) \ +{ \ + .name = n, \ + .offset = of, \ + .size = s, \ +} + +/** + * struct spear_smi_flash_info - platform structure for passing flash + * information + * + * name: name of the serial nor flash for identification + * mem_base: the memory base on which the flash is mapped + * size: size of the flash in bytes + * partitions: parition details + * nr_partitions: number of partitions + * fast_mode: whether flash supports fast mode + */ + +struct spear_smi_flash_info { + char *name; + unsigned long mem_base; + unsigned long size; + struct mtd_partition *partitions; + int nr_partitions; + u8 fast_mode; +}; + +/** + * struct spear_smi_plat_data - platform structure for configuring smi + * + * clk_rate: clk rate at which SMI must operate + * num_flashes: number of flashes present on board + * board_flash_info: specific details of each flash present on board + */ +struct spear_smi_plat_data { + unsigned long clk_rate; + int num_flashes; + struct spear_smi_flash_info *board_flash_info; + struct device_node *np[MAX_NUM_FLASH_CHIP]; +}; + +#endif /* __MTD_SPEAR_SMI_H */ diff --git a/include/linux/mtio.h b/include/linux/mtio.h index 8f825756c45..18543e2db06 100644 --- a/include/linux/mtio.h +++ b/include/linux/mtio.h @@ -194,6 +194,7 @@ struct mtpos { #define MT_ST_SYSV 0x1000 #define MT_ST_NOWAIT 0x2000 #define MT_ST_SILI 0x4000 +#define MT_ST_NOWAIT_EOF 0x8000 /* The mode parameters to be controlled. Parameter chosen with bits 20-28 */ #define MT_ST_CLEAR_DEFAULT 0xfffff diff --git a/include/linux/nfs4.h b/include/linux/nfs4.h index 834df8bf08b..0987146b063 100644 --- a/include/linux/nfs4.h +++ b/include/linux/nfs4.h @@ -438,7 +438,20 @@ enum limit_by4 { enum open_delegation_type4 { NFS4_OPEN_DELEGATE_NONE = 0, NFS4_OPEN_DELEGATE_READ = 1, - NFS4_OPEN_DELEGATE_WRITE = 2 + NFS4_OPEN_DELEGATE_WRITE = 2, + NFS4_OPEN_DELEGATE_NONE_EXT = 3, /* 4.1 */ +}; + +enum why_no_delegation4 { /* new to v4.1 */ + WND4_NOT_WANTED = 0, + WND4_CONTENTION = 1, + WND4_RESOURCE = 2, + WND4_NOT_SUPP_FTYPE = 3, + WND4_WRITE_DELEG_NOT_SUPP_FTYPE = 4, + WND4_NOT_SUPP_UPGRADE = 5, + WND4_NOT_SUPP_DOWNGRADE = 6, + WND4_CANCELLED = 7, + WND4_IS_DIR = 8, }; enum lock_type4 { diff --git a/include/linux/nfsd/cld.h b/include/linux/nfsd/cld.h new file mode 100644 index 00000000000..f14a9ab06f1 --- /dev/null +++ b/include/linux/nfsd/cld.h @@ -0,0 +1,56 @@ +/* + * Upcall description for nfsdcld communication + * + * Copyright (c) 2012 Red Hat, Inc. + * Author(s): Jeff Layton <jlayton@redhat.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef _NFSD_CLD_H +#define _NFSD_CLD_H + +/* latest upcall version available */ +#define CLD_UPCALL_VERSION 1 + +/* defined by RFC3530 */ +#define NFS4_OPAQUE_LIMIT 1024 + +enum cld_command { + Cld_Create, /* create a record for this cm_id */ + Cld_Remove, /* remove record of this cm_id */ + Cld_Check, /* is this cm_id allowed? */ + Cld_GraceDone, /* grace period is complete */ +}; + +/* representation of long-form NFSv4 client ID */ +struct cld_name { + uint16_t cn_len; /* length of cm_id */ + unsigned char cn_id[NFS4_OPAQUE_LIMIT]; /* client-provided */ +} __attribute__((packed)); + +/* message struct for communication with userspace */ +struct cld_msg { + uint8_t cm_vers; /* upcall version */ + uint8_t cm_cmd; /* upcall command */ + int16_t cm_status; /* return code */ + uint32_t cm_xid; /* transaction id */ + union { + int64_t cm_gracetime; /* grace period start time */ + struct cld_name cm_name; + } __attribute__((packed)) cm_u; +} __attribute__((packed)); + +#endif /* !_NFSD_CLD_H */ diff --git a/include/linux/of.h b/include/linux/of.h index d46a18ffbeb..fa7fb1d9745 100644 --- a/include/linux/of.h +++ b/include/linux/of.h @@ -58,9 +58,6 @@ struct device_node { struct kref kref; unsigned long _flags; void *data; -#if defined(CONFIG_EEH) - struct eeh_dev *edev; -#endif #if defined(CONFIG_SPARC) char *path_component_name; unsigned int unique_id; @@ -75,13 +72,6 @@ struct of_phandle_args { uint32_t args[MAX_PHANDLE_ARGS]; }; -#if defined(CONFIG_EEH) -static inline struct eeh_dev *of_node_to_eeh_dev(struct device_node *dn) -{ - return dn->edev; -} -#endif - #ifdef CONFIG_OF_DYNAMIC extern struct device_node *of_node_get(struct device_node *node); extern void of_node_put(struct device_node *node); @@ -361,6 +351,22 @@ static inline int of_machine_is_compatible(const char *compat) #define of_match_node(_matches, _node) NULL #endif /* CONFIG_OF */ +/** + * of_property_read_bool - Findfrom a property + * @np: device node from which the property value is to be read. + * @propname: name of the property to be searched. + * + * Search for a property in a device node. + * Returns true if the property exist false otherwise. + */ +static inline bool of_property_read_bool(const struct device_node *np, + const char *propname) +{ + struct property *prop = of_find_property(np, propname, NULL); + + return prop ? true : false; +} + static inline int of_property_read_u32(const struct device_node *np, const char *propname, u32 *out_value) diff --git a/include/linux/of_gpio.h b/include/linux/of_gpio.h index b254052a49d..81733d12cbe 100644 --- a/include/linux/of_gpio.h +++ b/include/linux/of_gpio.h @@ -50,7 +50,8 @@ static inline struct of_mm_gpio_chip *to_of_mm_gpio_chip(struct gpio_chip *gc) extern int of_get_named_gpio_flags(struct device_node *np, const char *list_name, int index, enum of_gpio_flags *flags); -extern unsigned int of_gpio_count(struct device_node *np); +extern unsigned int of_gpio_named_count(struct device_node *np, + const char* propname); extern int of_mm_gpiochip_add(struct device_node *np, struct of_mm_gpio_chip *mm_gc); @@ -71,7 +72,8 @@ static inline int of_get_named_gpio_flags(struct device_node *np, return -ENOSYS; } -static inline unsigned int of_gpio_count(struct device_node *np) +static inline unsigned int of_gpio_named_count(struct device_node *np, + const char* propname) { return 0; } @@ -89,6 +91,27 @@ static inline void of_gpiochip_remove(struct gpio_chip *gc) { } #endif /* CONFIG_OF_GPIO */ /** + * of_gpio_count - Count GPIOs for a device + * @np: device node to count GPIOs for + * + * The function returns the count of GPIOs specified for a node. + * + * Note that the empty GPIO specifiers counts too. For example, + * + * gpios = <0 + * &pio1 1 2 + * 0 + * &pio2 3 4>; + * + * defines four GPIOs (so this function will return 4), two of which + * are not specified. + */ +static inline unsigned int of_gpio_count(struct device_node *np) +{ + return of_gpio_named_count(np, "gpios"); +} + +/** * of_get_gpio_flags() - Get a GPIO number and flags to use with GPIO API * @np: device node to get GPIO from * @index: index of the GPIO diff --git a/include/linux/of_mtd.h b/include/linux/of_mtd.h new file mode 100644 index 00000000000..bae1b6094c6 --- /dev/null +++ b/include/linux/of_mtd.h @@ -0,0 +1,19 @@ +/* + * Copyright 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * OF helpers for mtd. + * + * This file is released under the GPLv2 + */ + +#ifndef __LINUX_OF_MTD_H +#define __LINUX_OF_NET_H + +#ifdef CONFIG_OF_MTD +#include <linux/of.h> +extern const int of_get_nand_ecc_mode(struct device_node *np); +int of_get_nand_bus_width(struct device_node *np); +bool of_get_nand_on_flash_bbt(struct device_node *np); +#endif + +#endif /* __LINUX_OF_MTD_H */ diff --git a/include/linux/parport.h b/include/linux/parport.h index 38a423ed3c0..106c2ca9440 100644 --- a/include/linux/parport.h +++ b/include/linux/parport.h @@ -100,7 +100,6 @@ typedef enum { #include <linux/wait.h> #include <linux/irqreturn.h> #include <linux/semaphore.h> -#include <asm/system.h> #include <asm/ptrace.h> /* Define this later. */ diff --git a/include/linux/pid_namespace.h b/include/linux/pid_namespace.h index f5bd679be46..b067bd8c49d 100644 --- a/include/linux/pid_namespace.h +++ b/include/linux/pid_namespace.h @@ -33,6 +33,7 @@ struct pid_namespace { #endif gid_t pid_gid; int hide_pid; + int reboot; /* group exit code if this pidns was rebooted */ }; extern struct pid_namespace init_pid_ns; @@ -48,6 +49,7 @@ static inline struct pid_namespace *get_pid_ns(struct pid_namespace *ns) extern struct pid_namespace *copy_pid_ns(unsigned long flags, struct pid_namespace *ns); extern void free_pid_ns(struct kref *kref); extern void zap_pid_ns_processes(struct pid_namespace *pid_ns); +extern int reboot_pid_ns(struct pid_namespace *pid_ns, int cmd); static inline void put_pid_ns(struct pid_namespace *ns) { @@ -75,11 +77,15 @@ static inline void put_pid_ns(struct pid_namespace *ns) { } - static inline void zap_pid_ns_processes(struct pid_namespace *ns) { BUG(); } + +static inline int reboot_pid_ns(struct pid_namespace *pid_ns, int cmd) +{ + return 0; +} #endif /* CONFIG_PID_NS */ extern struct pid_namespace *task_active_pid_ns(struct task_struct *tsk); diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h new file mode 100644 index 00000000000..b0f2c56a8ea --- /dev/null +++ b/include/linux/platform_data/atmel.h @@ -0,0 +1,27 @@ +/* + * atmel platform data + * + * GPL v2 Only + */ + +#ifndef __ATMEL_H__ +#define __ATMEL_H__ + +#include <linux/mtd/nand.h> + + /* NAND / SmartMedia */ +struct atmel_nand_data { + int enable_pin; /* chip enable */ + int det_pin; /* card detect */ + int rdy_pin; /* ready/busy */ + u8 rdy_pin_active_low; /* rdy_pin value is inverted */ + u8 ale; /* address line number connected to ALE */ + u8 cle; /* address line number connected to CLE */ + u8 bus_width_16; /* buswidth is 16 bit */ + u8 ecc_mode; /* ecc mode */ + u8 on_flash_bbt; /* bbt on flash */ + struct mtd_partition *parts; + unsigned int num_parts; +}; + +#endif /* __ATMEL_H__ */ diff --git a/include/linux/platform_data/spear_thermal.h b/include/linux/platform_data/spear_thermal.h new file mode 100644 index 00000000000..724f2e1cbbc --- /dev/null +++ b/include/linux/platform_data/spear_thermal.h @@ -0,0 +1,26 @@ +/* + * SPEAr thermal driver platform data. + * + * Copyright (C) 2011-2012 ST Microelectronics + * Author: Vincenzo Frascino <vincenzo.frascino@st.com> + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ +#ifndef SPEAR_THERMAL_H +#define SPEAR_THERMAL_H + +/* SPEAr Thermal Sensor Platform Data */ +struct spear_thermal_pdata { + /* flags used to enable thermal sensor */ + unsigned int thermal_flags; +}; + +#endif /* SPEAR_THERMAL_H */ diff --git a/include/linux/platform_data/tegra_emc.h b/include/linux/platform_data/tegra_emc.h new file mode 100644 index 00000000000..df67505e98f --- /dev/null +++ b/include/linux/platform_data/tegra_emc.h @@ -0,0 +1,34 @@ +/* + * Copyright (C) 2011 Google, Inc. + * + * Author: + * Colin Cross <ccross@android.com> + * Olof Johansson <olof@lixom.net> + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef __TEGRA_EMC_H_ +#define __TEGRA_EMC_H_ + +#define TEGRA_EMC_NUM_REGS 46 + +struct tegra_emc_table { + unsigned long rate; + u32 regs[TEGRA_EMC_NUM_REGS]; +}; + +struct tegra_emc_pdata { + int num_tables; + struct tegra_emc_table *tables; +}; + +#endif diff --git a/include/linux/power/max17042_battery.h b/include/linux/power/max17042_battery.h index fe99211fb2b..e01b167e66f 100644 --- a/include/linux/power/max17042_battery.h +++ b/include/linux/power/max17042_battery.h @@ -27,6 +27,8 @@ #define MAX17042_BATTERY_FULL (100) #define MAX17042_DEFAULT_SNS_RESISTOR (10000) +#define MAX17042_CHARACTERIZATION_DATA_SIZE 48 + enum max17042_register { MAX17042_STATUS = 0x00, MAX17042_VALRT_Th = 0x01, @@ -40,11 +42,11 @@ enum max17042_register { MAX17042_VCELL = 0x09, MAX17042_Current = 0x0A, MAX17042_AvgCurrent = 0x0B, - MAX17042_Qresidual = 0x0C, + MAX17042_SOC = 0x0D, MAX17042_AvSOC = 0x0E, MAX17042_RemCap = 0x0F, - MAX17402_FullCAP = 0x10, + MAX17042_FullCAP = 0x10, MAX17042_TTE = 0x11, MAX17042_V_empty = 0x12, @@ -62,14 +64,14 @@ enum max17042_register { MAX17042_AvCap = 0x1F, MAX17042_ManName = 0x20, MAX17042_DevName = 0x21, - MAX17042_DevChem = 0x22, + MAX17042_FullCAPNom = 0x23, MAX17042_TempNom = 0x24, - MAX17042_TempCold = 0x25, + MAX17042_TempLim = 0x25, MAX17042_TempHot = 0x26, MAX17042_AIN = 0x27, MAX17042_LearnCFG = 0x28, - MAX17042_SHFTCFG = 0x29, + MAX17042_FilterCFG = 0x29, MAX17042_RelaxCFG = 0x2A, MAX17042_MiscCFG = 0x2B, MAX17042_TGAIN = 0x2C, @@ -77,22 +79,41 @@ enum max17042_register { MAX17042_CGAIN = 0x2E, MAX17042_COFF = 0x2F, - MAX17042_Q_empty = 0x33, + MAX17042_MaskSOC = 0x32, + MAX17042_SOC_empty = 0x33, MAX17042_T_empty = 0x34, + MAX17042_FullCAP0 = 0x35, + MAX17042_LAvg_empty = 0x36, + MAX17042_FCTC = 0x37, MAX17042_RCOMP0 = 0x38, MAX17042_TempCo = 0x39, - MAX17042_Rx = 0x3A, - MAX17042_T_empty0 = 0x3B, + MAX17042_EmptyTempCo = 0x3A, + MAX17042_K_empty0 = 0x3B, MAX17042_TaskPeriod = 0x3C, MAX17042_FSTAT = 0x3D, MAX17042_SHDNTIMER = 0x3F, - MAX17042_VFRemCap = 0x4A, + MAX17042_dQacc = 0x45, + MAX17042_dPacc = 0x46, + + MAX17042_VFSOC0 = 0x48, MAX17042_QH = 0x4D, MAX17042_QL = 0x4E, + + MAX17042_VFSOC0Enable = 0x60, + MAX17042_MLOCKReg1 = 0x62, + MAX17042_MLOCKReg2 = 0x63, + + MAX17042_MODELChrTbl = 0x80, + + MAX17042_OCV = 0xEE, + + MAX17042_OCVInternal = 0xFB, + + MAX17042_VFSOC = 0xFF, }; /* @@ -105,10 +126,64 @@ struct max17042_reg_data { u16 data; }; +struct max17042_config_data { + /* External current sense resistor value in milli-ohms */ + u32 cur_sense_val; + + /* A/D measurement */ + u16 tgain; /* 0x2C */ + u16 toff; /* 0x2D */ + u16 cgain; /* 0x2E */ + u16 coff; /* 0x2F */ + + /* Alert / Status */ + u16 valrt_thresh; /* 0x01 */ + u16 talrt_thresh; /* 0x02 */ + u16 soc_alrt_thresh; /* 0x03 */ + u16 config; /* 0x01D */ + u16 shdntimer; /* 0x03F */ + + /* App data */ + u16 design_cap; /* 0x18 */ + u16 ichgt_term; /* 0x1E */ + + /* MG3 config */ + u16 at_rate; /* 0x04 */ + u16 learn_cfg; /* 0x28 */ + u16 filter_cfg; /* 0x29 */ + u16 relax_cfg; /* 0x2A */ + u16 misc_cfg; /* 0x2B */ + u16 masksoc; /* 0x32 */ + + /* MG3 save and restore */ + u16 fullcap; /* 0x10 */ + u16 fullcapnom; /* 0x23 */ + u16 socempty; /* 0x33 */ + u16 lavg_empty; /* 0x36 */ + u16 dqacc; /* 0x45 */ + u16 dpacc; /* 0x46 */ + + /* Cell technology from power_supply.h */ + u16 cell_technology; + + /* Cell Data */ + u16 vempty; /* 0x12 */ + u16 temp_nom; /* 0x24 */ + u16 temp_lim; /* 0x25 */ + u16 fctc; /* 0x37 */ + u16 rcomp0; /* 0x38 */ + u16 tcompc0; /* 0x39 */ + u16 empty_tempco; /* 0x3A */ + u16 kempty0; /* 0x3B */ + u16 cell_char_tbl[MAX17042_CHARACTERIZATION_DATA_SIZE]; +} __packed; + struct max17042_platform_data { struct max17042_reg_data *init_data; + struct max17042_config_data *config_data; int num_init_data; /* Number of enties in init_data array */ bool enable_current_sense; + bool enable_por_init; /* Use POR init from Maxim appnote */ /* * R_sns in micro-ohms. diff --git a/include/linux/power/smb347-charger.h b/include/linux/power/smb347-charger.h new file mode 100644 index 00000000000..b3cb20dab55 --- /dev/null +++ b/include/linux/power/smb347-charger.h @@ -0,0 +1,117 @@ +/* + * Summit Microelectronics SMB347 Battery Charger Driver + * + * Copyright (C) 2011, Intel Corporation + * + * Authors: Bruce E. Robertson <bruce.e.robertson@intel.com> + * Mika Westerberg <mika.westerberg@linux.intel.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef SMB347_CHARGER_H +#define SMB347_CHARGER_H + +#include <linux/types.h> +#include <linux/power_supply.h> + +enum { + /* use the default compensation method */ + SMB347_SOFT_TEMP_COMPENSATE_DEFAULT = -1, + + SMB347_SOFT_TEMP_COMPENSATE_NONE, + SMB347_SOFT_TEMP_COMPENSATE_CURRENT, + SMB347_SOFT_TEMP_COMPENSATE_VOLTAGE, +}; + +/* Use default factory programmed value for hard/soft temperature limit */ +#define SMB347_TEMP_USE_DEFAULT -273 + +/* + * Charging enable can be controlled by software (via i2c) by + * smb347-charger driver or by EN pin (active low/high). + */ +enum smb347_chg_enable { + SMB347_CHG_ENABLE_SW, + SMB347_CHG_ENABLE_PIN_ACTIVE_LOW, + SMB347_CHG_ENABLE_PIN_ACTIVE_HIGH, +}; + +/** + * struct smb347_charger_platform_data - platform data for SMB347 charger + * @battery_info: Information about the battery + * @max_charge_current: maximum current (in uA) the battery can be charged + * @max_charge_voltage: maximum voltage (in uV) the battery can be charged + * @pre_charge_current: current (in uA) to use in pre-charging phase + * @termination_current: current (in uA) used to determine when the + * charging cycle terminates + * @pre_to_fast_voltage: voltage (in uV) treshold used for transitioning to + * pre-charge to fast charge mode + * @mains_current_limit: maximum input current drawn from AC/DC input (in uA) + * @usb_hc_current_limit: maximum input high current (in uA) drawn from USB + * input + * @chip_temp_threshold: die temperature where device starts limiting charge + * current [%100 - %130] (in degree C) + * @soft_cold_temp_limit: soft cold temperature limit [%0 - %15] (in degree C), + * granularity is 5 deg C. + * @soft_hot_temp_limit: soft hot temperature limit [%40 - %55] (in degree C), + * granularity is 5 deg C. + * @hard_cold_temp_limit: hard cold temperature limit [%-5 - %10] (in degree C), + * granularity is 5 deg C. + * @hard_hot_temp_limit: hard hot temperature limit [%50 - %65] (in degree C), + * granularity is 5 deg C. + * @suspend_on_hard_temp_limit: suspend charging when hard limit is hit + * @soft_temp_limit_compensation: compensation method when soft temperature + * limit is hit + * @charge_current_compensation: current (in uA) for charging compensation + * current when temperature hits soft limits + * @use_mains: AC/DC input can be used + * @use_usb: USB input can be used + * @use_usb_otg: USB OTG output can be used (not implemented yet) + * @irq_gpio: GPIO number used for interrupts (%-1 if not used) + * @enable_control: how charging enable/disable is controlled + * (driver/pin controls) + * + * @use_main, @use_usb, and @use_usb_otg are means to enable/disable + * hardware support for these. This is useful when we want to have for + * example OTG charging controlled via OTG transceiver driver and not by + * the SMB347 hardware. + * + * Hard and soft temperature limit values are given as described in the + * device data sheet and assuming NTC beta value is %3750. Even if this is + * not the case, these values should be used. They can be mapped to the + * corresponding NTC beta values with the help of table %2 in the data + * sheet. So for example if NTC beta is %3375 and we want to program hard + * hot limit to be %53 deg C, @hard_hot_temp_limit should be set to %50. + * + * If zero value is given in any of the current and voltage values, the + * factory programmed default will be used. For soft/hard temperature + * values, pass in %SMB347_TEMP_USE_DEFAULT instead. + */ +struct smb347_charger_platform_data { + struct power_supply_info battery_info; + unsigned int max_charge_current; + unsigned int max_charge_voltage; + unsigned int pre_charge_current; + unsigned int termination_current; + unsigned int pre_to_fast_voltage; + unsigned int mains_current_limit; + unsigned int usb_hc_current_limit; + unsigned int chip_temp_threshold; + int soft_cold_temp_limit; + int soft_hot_temp_limit; + int hard_cold_temp_limit; + int hard_hot_temp_limit; + bool suspend_on_hard_temp_limit; + unsigned int soft_temp_limit_compensation; + unsigned int charge_current_compensation; + bool use_mains; + bool use_usb; + bool use_usb_otg; + int irq_gpio; + enum smb347_chg_enable enable_control; +}; + +#endif /* SMB347_CHARGER_H */ diff --git a/include/linux/radix-tree.h b/include/linux/radix-tree.h index e9a48234e69..0d04cd69ab9 100644 --- a/include/linux/radix-tree.h +++ b/include/linux/radix-tree.h @@ -2,6 +2,7 @@ * Copyright (C) 2001 Momchil Velikov * Portions Copyright (C) 2001 Christoph Hellwig * Copyright (C) 2006 Nick Piggin + * Copyright (C) 2012 Konstantin Khlebnikov * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -257,4 +258,199 @@ static inline void radix_tree_preload_end(void) preempt_enable(); } +/** + * struct radix_tree_iter - radix tree iterator state + * + * @index: index of current slot + * @next_index: next-to-last index for this chunk + * @tags: bit-mask for tag-iterating + * + * This radix tree iterator works in terms of "chunks" of slots. A chunk is a + * subinterval of slots contained within one radix tree leaf node. It is + * described by a pointer to its first slot and a struct radix_tree_iter + * which holds the chunk's position in the tree and its size. For tagged + * iteration radix_tree_iter also holds the slots' bit-mask for one chosen + * radix tree tag. + */ +struct radix_tree_iter { + unsigned long index; + unsigned long next_index; + unsigned long tags; +}; + +#define RADIX_TREE_ITER_TAG_MASK 0x00FF /* tag index in lower byte */ +#define RADIX_TREE_ITER_TAGGED 0x0100 /* lookup tagged slots */ +#define RADIX_TREE_ITER_CONTIG 0x0200 /* stop at first hole */ + +/** + * radix_tree_iter_init - initialize radix tree iterator + * + * @iter: pointer to iterator state + * @start: iteration starting index + * Returns: NULL + */ +static __always_inline void ** +radix_tree_iter_init(struct radix_tree_iter *iter, unsigned long start) +{ + /* + * Leave iter->tags uninitialized. radix_tree_next_chunk() will fill it + * in the case of a successful tagged chunk lookup. If the lookup was + * unsuccessful or non-tagged then nobody cares about ->tags. + * + * Set index to zero to bypass next_index overflow protection. + * See the comment in radix_tree_next_chunk() for details. + */ + iter->index = 0; + iter->next_index = start; + return NULL; +} + +/** + * radix_tree_next_chunk - find next chunk of slots for iteration + * + * @root: radix tree root + * @iter: iterator state + * @flags: RADIX_TREE_ITER_* flags and tag index + * Returns: pointer to chunk first slot, or NULL if there no more left + * + * This function looks up the next chunk in the radix tree starting from + * @iter->next_index. It returns a pointer to the chunk's first slot. + * Also it fills @iter with data about chunk: position in the tree (index), + * its end (next_index), and constructs a bit mask for tagged iterating (tags). + */ +void **radix_tree_next_chunk(struct radix_tree_root *root, + struct radix_tree_iter *iter, unsigned flags); + +/** + * radix_tree_chunk_size - get current chunk size + * + * @iter: pointer to radix tree iterator + * Returns: current chunk size + */ +static __always_inline unsigned +radix_tree_chunk_size(struct radix_tree_iter *iter) +{ + return iter->next_index - iter->index; +} + +/** + * radix_tree_next_slot - find next slot in chunk + * + * @slot: pointer to current slot + * @iter: pointer to interator state + * @flags: RADIX_TREE_ITER_*, should be constant + * Returns: pointer to next slot, or NULL if there no more left + * + * This function updates @iter->index in the case of a successful lookup. + * For tagged lookup it also eats @iter->tags. + */ +static __always_inline void ** +radix_tree_next_slot(void **slot, struct radix_tree_iter *iter, unsigned flags) +{ + if (flags & RADIX_TREE_ITER_TAGGED) { + iter->tags >>= 1; + if (likely(iter->tags & 1ul)) { + iter->index++; + return slot + 1; + } + if (!(flags & RADIX_TREE_ITER_CONTIG) && likely(iter->tags)) { + unsigned offset = __ffs(iter->tags); + + iter->tags >>= offset; + iter->index += offset + 1; + return slot + offset + 1; + } + } else { + unsigned size = radix_tree_chunk_size(iter) - 1; + + while (size--) { + slot++; + iter->index++; + if (likely(*slot)) + return slot; + if (flags & RADIX_TREE_ITER_CONTIG) + break; + } + } + return NULL; +} + +/** + * radix_tree_for_each_chunk - iterate over chunks + * + * @slot: the void** variable for pointer to chunk first slot + * @root: the struct radix_tree_root pointer + * @iter: the struct radix_tree_iter pointer + * @start: iteration starting index + * @flags: RADIX_TREE_ITER_* and tag index + * + * Locks can be released and reacquired between iterations. + */ +#define radix_tree_for_each_chunk(slot, root, iter, start, flags) \ + for (slot = radix_tree_iter_init(iter, start) ; \ + (slot = radix_tree_next_chunk(root, iter, flags)) ;) + +/** + * radix_tree_for_each_chunk_slot - iterate over slots in one chunk + * + * @slot: the void** variable, at the beginning points to chunk first slot + * @iter: the struct radix_tree_iter pointer + * @flags: RADIX_TREE_ITER_*, should be constant + * + * This macro is designed to be nested inside radix_tree_for_each_chunk(). + * @slot points to the radix tree slot, @iter->index contains its index. + */ +#define radix_tree_for_each_chunk_slot(slot, iter, flags) \ + for (; slot ; slot = radix_tree_next_slot(slot, iter, flags)) + +/** + * radix_tree_for_each_slot - iterate over non-empty slots + * + * @slot: the void** variable for pointer to slot + * @root: the struct radix_tree_root pointer + * @iter: the struct radix_tree_iter pointer + * @start: iteration starting index + * + * @slot points to radix tree slot, @iter->index contains its index. + */ +#define radix_tree_for_each_slot(slot, root, iter, start) \ + for (slot = radix_tree_iter_init(iter, start) ; \ + slot || (slot = radix_tree_next_chunk(root, iter, 0)) ; \ + slot = radix_tree_next_slot(slot, iter, 0)) + +/** + * radix_tree_for_each_contig - iterate over contiguous slots + * + * @slot: the void** variable for pointer to slot + * @root: the struct radix_tree_root pointer + * @iter: the struct radix_tree_iter pointer + * @start: iteration starting index + * + * @slot points to radix tree slot, @iter->index contains its index. + */ +#define radix_tree_for_each_contig(slot, root, iter, start) \ + for (slot = radix_tree_iter_init(iter, start) ; \ + slot || (slot = radix_tree_next_chunk(root, iter, \ + RADIX_TREE_ITER_CONTIG)) ; \ + slot = radix_tree_next_slot(slot, iter, \ + RADIX_TREE_ITER_CONTIG)) + +/** + * radix_tree_for_each_tagged - iterate over tagged slots + * + * @slot: the void** variable for pointer to slot + * @root: the struct radix_tree_root pointer + * @iter: the struct radix_tree_iter pointer + * @start: iteration starting index + * @tag: tag index + * + * @slot points to radix tree slot, @iter->index contains its index. + */ +#define radix_tree_for_each_tagged(slot, root, iter, start, tag) \ + for (slot = radix_tree_iter_init(iter, start) ; \ + slot || (slot = radix_tree_next_chunk(root, iter, \ + RADIX_TREE_ITER_TAGGED | tag)) ; \ + slot = radix_tree_next_slot(slot, iter, \ + RADIX_TREE_ITER_TAGGED)) + #endif /* _LINUX_RADIX_TREE_H */ diff --git a/include/linux/regulator/ab8500.h b/include/linux/regulator/ab8500.h index 76579f964a2..7bd73bbdfd1 100644 --- a/include/linux/regulator/ab8500.h +++ b/include/linux/regulator/ab8500.h @@ -26,7 +26,26 @@ enum ab8500_regulator_id { AB8500_NUM_REGULATORS, }; -/* AB8500 register initialization */ +/* AB9450 regulators */ +enum ab9540_regulator_id { + AB9540_LDO_AUX1, + AB9540_LDO_AUX2, + AB9540_LDO_AUX3, + AB9540_LDO_AUX4, + AB9540_LDO_INTCORE, + AB9540_LDO_TVOUT, + AB9540_LDO_USB, + AB9540_LDO_AUDIO, + AB9540_LDO_ANAMIC1, + AB9540_LDO_ANAMIC2, + AB9540_LDO_DMIC, + AB9540_LDO_ANA, + AB9540_SYSCLKREQ_2, + AB9540_SYSCLKREQ_4, + AB9540_NUM_REGULATORS, +}; + +/* AB8500 and AB9540 register initialization */ struct ab8500_regulator_reg_init { int id; u8 value; @@ -71,4 +90,53 @@ enum ab8500_regulator_reg { AB8500_NUM_REGULATOR_REGISTERS, }; + +/* AB9540 registers */ +enum ab9540_regulator_reg { + AB9540_REGUREQUESTCTRL1, + AB9540_REGUREQUESTCTRL2, + AB9540_REGUREQUESTCTRL3, + AB9540_REGUREQUESTCTRL4, + AB9540_REGUSYSCLKREQ1HPVALID1, + AB9540_REGUSYSCLKREQ1HPVALID2, + AB9540_REGUHWHPREQ1VALID1, + AB9540_REGUHWHPREQ1VALID2, + AB9540_REGUHWHPREQ2VALID1, + AB9540_REGUHWHPREQ2VALID2, + AB9540_REGUSWHPREQVALID1, + AB9540_REGUSWHPREQVALID2, + AB9540_REGUSYSCLKREQVALID1, + AB9540_REGUSYSCLKREQVALID2, + AB9540_REGUVAUX4REQVALID, + AB9540_REGUMISC1, + AB9540_VAUDIOSUPPLY, + AB9540_REGUCTRL1VAMIC, + AB9540_VSMPS1REGU, + AB9540_VSMPS2REGU, + AB9540_VSMPS3REGU, /* NOTE! PRCMU register */ + AB9540_VPLLVANAREGU, + AB9540_EXTSUPPLYREGU, + AB9540_VAUX12REGU, + AB9540_VRF1VAUX3REGU, + AB9540_VSMPS1SEL1, + AB9540_VSMPS1SEL2, + AB9540_VSMPS1SEL3, + AB9540_VSMPS2SEL1, + AB9540_VSMPS2SEL2, + AB9540_VSMPS2SEL3, + AB9540_VSMPS3SEL1, /* NOTE! PRCMU register */ + AB9540_VSMPS3SEL2, /* NOTE! PRCMU register */ + AB9540_VAUX1SEL, + AB9540_VAUX2SEL, + AB9540_VRF1VAUX3SEL, + AB9540_REGUCTRL2SPARE, + AB9540_VAUX4REQCTRL, + AB9540_VAUX4REGU, + AB9540_VAUX4SEL, + AB9540_REGUCTRLDISCH, + AB9540_REGUCTRLDISCH2, + AB9540_REGUCTRLDISCH3, + AB9540_NUM_REGULATOR_REGISTERS, +}; + #endif diff --git a/include/linux/regulator/bq24022.h b/include/linux/regulator/bq24022.h deleted file mode 100644 index a6d014005d4..00000000000 --- a/include/linux/regulator/bq24022.h +++ /dev/null @@ -1,24 +0,0 @@ -/* - * Support for TI bq24022 (bqTINY-II) Dual Input (USB/AC Adpater) - * 1-Cell Li-Ion Charger connected via GPIOs. - * - * Copyright (c) 2008 Philipp Zabel - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - */ - -struct regulator_init_data; - -/** - * bq24022_mach_info - platform data for bq24022 - * @gpio_nce: GPIO line connected to the nCE pin, used to enable / disable charging - * @gpio_iset2: GPIO line connected to the ISET2 pin, used to limit charging current to 100 mA / 500 mA - */ -struct bq24022_mach_info { - int gpio_nce; - int gpio_iset2; - struct regulator_init_data *init_data; -}; diff --git a/include/linux/remoteproc.h b/include/linux/remoteproc.h new file mode 100644 index 00000000000..f1ffabb978d --- /dev/null +++ b/include/linux/remoteproc.h @@ -0,0 +1,478 @@ +/* + * Remote Processor Framework + * + * Copyright(c) 2011 Texas Instruments, Inc. + * Copyright(c) 2011 Google, Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name Texas Instruments nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +#ifndef REMOTEPROC_H +#define REMOTEPROC_H + +#include <linux/types.h> +#include <linux/kref.h> +#include <linux/klist.h> +#include <linux/mutex.h> +#include <linux/virtio.h> +#include <linux/completion.h> +#include <linux/idr.h> + +/** + * struct resource_table - firmware resource table header + * @ver: version number + * @num: number of resource entries + * @reserved: reserved (must be zero) + * @offset: array of offsets pointing at the various resource entries + * + * A resource table is essentially a list of system resources required + * by the remote processor. It may also include configuration entries. + * If needed, the remote processor firmware should contain this table + * as a dedicated ".resource_table" ELF section. + * + * Some resources entries are mere announcements, where the host is informed + * of specific remoteproc configuration. Other entries require the host to + * do something (e.g. allocate a system resource). Sometimes a negotiation + * is expected, where the firmware requests a resource, and once allocated, + * the host should provide back its details (e.g. address of an allocated + * memory region). + * + * The header of the resource table, as expressed by this structure, + * contains a version number (should we need to change this format in the + * future), the number of available resource entries, and their offsets + * in the table. + * + * Immediately following this header are the resource entries themselves, + * each of which begins with a resource entry header (as described below). + */ +struct resource_table { + u32 ver; + u32 num; + u32 reserved[2]; + u32 offset[0]; +} __packed; + +/** + * struct fw_rsc_hdr - firmware resource entry header + * @type: resource type + * @data: resource data + * + * Every resource entry begins with a 'struct fw_rsc_hdr' header providing + * its @type. The content of the entry itself will immediately follow + * this header, and it should be parsed according to the resource type. + */ +struct fw_rsc_hdr { + u32 type; + u8 data[0]; +} __packed; + +/** + * enum fw_resource_type - types of resource entries + * + * @RSC_CARVEOUT: request for allocation of a physically contiguous + * memory region. + * @RSC_DEVMEM: request to iommu_map a memory-based peripheral. + * @RSC_TRACE: announces the availability of a trace buffer into which + * the remote processor will be writing logs. + * @RSC_VDEV: declare support for a virtio device, and serve as its + * virtio header. + * @RSC_LAST: just keep this one at the end + * + * For more details regarding a specific resource type, please see its + * dedicated structure below. + * + * Please note that these values are used as indices to the rproc_handle_rsc + * lookup table, so please keep them sane. Moreover, @RSC_LAST is used to + * check the validity of an index before the lookup table is accessed, so + * please update it as needed. + */ +enum fw_resource_type { + RSC_CARVEOUT = 0, + RSC_DEVMEM = 1, + RSC_TRACE = 2, + RSC_VDEV = 3, + RSC_LAST = 4, +}; + +#define FW_RSC_ADDR_ANY (0xFFFFFFFFFFFFFFFF) + +/** + * struct fw_rsc_carveout - physically contiguous memory request + * @da: device address + * @pa: physical address + * @len: length (in bytes) + * @flags: iommu protection flags + * @reserved: reserved (must be zero) + * @name: human-readable name of the requested memory region + * + * This resource entry requests the host to allocate a physically contiguous + * memory region. + * + * These request entries should precede other firmware resource entries, + * as other entries might request placing other data objects inside + * these memory regions (e.g. data/code segments, trace resource entries, ...). + * + * Allocating memory this way helps utilizing the reserved physical memory + * (e.g. CMA) more efficiently, and also minimizes the number of TLB entries + * needed to map it (in case @rproc is using an IOMMU). Reducing the TLB + * pressure is important; it may have a substantial impact on performance. + * + * If the firmware is compiled with static addresses, then @da should specify + * the expected device address of this memory region. If @da is set to + * FW_RSC_ADDR_ANY, then the host will dynamically allocate it, and then + * overwrite @da with the dynamically allocated address. + * + * We will always use @da to negotiate the device addresses, even if it + * isn't using an iommu. In that case, though, it will obviously contain + * physical addresses. + * + * Some remote processors needs to know the allocated physical address + * even if they do use an iommu. This is needed, e.g., if they control + * hardware accelerators which access the physical memory directly (this + * is the case with OMAP4 for instance). In that case, the host will + * overwrite @pa with the dynamically allocated physical address. + * Generally we don't want to expose physical addresses if we don't have to + * (remote processors are generally _not_ trusted), so we might want to + * change this to happen _only_ when explicitly required by the hardware. + * + * @flags is used to provide IOMMU protection flags, and @name should + * (optionally) contain a human readable name of this carveout region + * (mainly for debugging purposes). + */ +struct fw_rsc_carveout { + u32 da; + u32 pa; + u32 len; + u32 flags; + u32 reserved; + u8 name[32]; +} __packed; + +/** + * struct fw_rsc_devmem - iommu mapping request + * @da: device address + * @pa: physical address + * @len: length (in bytes) + * @flags: iommu protection flags + * @reserved: reserved (must be zero) + * @name: human-readable name of the requested region to be mapped + * + * This resource entry requests the host to iommu map a physically contiguous + * memory region. This is needed in case the remote processor requires + * access to certain memory-based peripherals; _never_ use it to access + * regular memory. + * + * This is obviously only needed if the remote processor is accessing memory + * via an iommu. + * + * @da should specify the required device address, @pa should specify + * the physical address we want to map, @len should specify the size of + * the mapping and @flags is the IOMMU protection flags. As always, @name may + * (optionally) contain a human readable name of this mapping (mainly for + * debugging purposes). + * + * Note: at this point we just "trust" those devmem entries to contain valid + * physical addresses, but this isn't safe and will be changed: eventually we + * want remoteproc implementations to provide us ranges of physical addresses + * the firmware is allowed to request, and not allow firmwares to request + * access to physical addresses that are outside those ranges. + */ +struct fw_rsc_devmem { + u32 da; + u32 pa; + u32 len; + u32 flags; + u32 reserved; + u8 name[32]; +} __packed; + +/** + * struct fw_rsc_trace - trace buffer declaration + * @da: device address + * @len: length (in bytes) + * @reserved: reserved (must be zero) + * @name: human-readable name of the trace buffer + * + * This resource entry provides the host information about a trace buffer + * into which the remote processor will write log messages. + * + * @da specifies the device address of the buffer, @len specifies + * its size, and @name may contain a human readable name of the trace buffer. + * + * After booting the remote processor, the trace buffers are exposed to the + * user via debugfs entries (called trace0, trace1, etc..). + */ +struct fw_rsc_trace { + u32 da; + u32 len; + u32 reserved; + u8 name[32]; +} __packed; + +/** + * struct fw_rsc_vdev_vring - vring descriptor entry + * @da: device address + * @align: the alignment between the consumer and producer parts of the vring + * @num: num of buffers supported by this vring (must be power of two) + * @notifyid is a unique rproc-wide notify index for this vring. This notify + * index is used when kicking a remote processor, to let it know that this + * vring is triggered. + * @reserved: reserved (must be zero) + * + * This descriptor is not a resource entry by itself; it is part of the + * vdev resource type (see below). + * + * Note that @da should either contain the device address where + * the remote processor is expecting the vring, or indicate that + * dynamically allocation of the vring's device address is supported. + */ +struct fw_rsc_vdev_vring { + u32 da; + u32 align; + u32 num; + u32 notifyid; + u32 reserved; +} __packed; + +/** + * struct fw_rsc_vdev - virtio device header + * @id: virtio device id (as in virtio_ids.h) + * @notifyid is a unique rproc-wide notify index for this vdev. This notify + * index is used when kicking a remote processor, to let it know that the + * status/features of this vdev have changes. + * @dfeatures specifies the virtio device features supported by the firmware + * @gfeatures is a place holder used by the host to write back the + * negotiated features that are supported by both sides. + * @config_len is the size of the virtio config space of this vdev. The config + * space lies in the resource table immediate after this vdev header. + * @status is a place holder where the host will indicate its virtio progress. + * @num_of_vrings indicates how many vrings are described in this vdev header + * @reserved: reserved (must be zero) + * @vring is an array of @num_of_vrings entries of 'struct fw_rsc_vdev_vring'. + * + * This resource is a virtio device header: it provides information about + * the vdev, and is then used by the host and its peer remote processors + * to negotiate and share certain virtio properties. + * + * By providing this resource entry, the firmware essentially asks remoteproc + * to statically allocate a vdev upon registration of the rproc (dynamic vdev + * allocation is not yet supported). + * + * Note: unlike virtualization systems, the term 'host' here means + * the Linux side which is running remoteproc to control the remote + * processors. We use the name 'gfeatures' to comply with virtio's terms, + * though there isn't really any virtualized guest OS here: it's the host + * which is responsible for negotiating the final features. + * Yeah, it's a bit confusing. + * + * Note: immediately following this structure is the virtio config space for + * this vdev (which is specific to the vdev; for more info, read the virtio + * spec). the size of the config space is specified by @config_len. + */ +struct fw_rsc_vdev { + u32 id; + u32 notifyid; + u32 dfeatures; + u32 gfeatures; + u32 config_len; + u8 status; + u8 num_of_vrings; + u8 reserved[2]; + struct fw_rsc_vdev_vring vring[0]; +} __packed; + +/** + * struct rproc_mem_entry - memory entry descriptor + * @va: virtual address + * @dma: dma address + * @len: length, in bytes + * @da: device address + * @priv: associated data + * @node: list node + */ +struct rproc_mem_entry { + void *va; + dma_addr_t dma; + int len; + u32 da; + void *priv; + struct list_head node; +}; + +struct rproc; + +/** + * struct rproc_ops - platform-specific device handlers + * @start: power on the device and boot it + * @stop: power off the device + * @kick: kick a virtqueue (virtqueue id given as a parameter) + */ +struct rproc_ops { + int (*start)(struct rproc *rproc); + int (*stop)(struct rproc *rproc); + void (*kick)(struct rproc *rproc, int vqid); +}; + +/** + * enum rproc_state - remote processor states + * @RPROC_OFFLINE: device is powered off + * @RPROC_SUSPENDED: device is suspended; needs to be woken up to receive + * a message. + * @RPROC_RUNNING: device is up and running + * @RPROC_CRASHED: device has crashed; need to start recovery + * @RPROC_LAST: just keep this one at the end + * + * Please note that the values of these states are used as indices + * to rproc_state_string, a state-to-name lookup table, + * so please keep the two synchronized. @RPROC_LAST is used to check + * the validity of an index before the lookup table is accessed, so + * please update it as needed too. + */ +enum rproc_state { + RPROC_OFFLINE = 0, + RPROC_SUSPENDED = 1, + RPROC_RUNNING = 2, + RPROC_CRASHED = 3, + RPROC_LAST = 4, +}; + +/** + * struct rproc - represents a physical remote processor device + * @node: klist node of this rproc object + * @domain: iommu domain + * @name: human readable name of the rproc + * @firmware: name of firmware file to be loaded + * @priv: private data which belongs to the platform-specific rproc module + * @ops: platform-specific start/stop rproc handlers + * @dev: underlying device + * @refcount: refcount of users that have a valid pointer to this rproc + * @power: refcount of users who need this rproc powered up + * @state: state of the device + * @lock: lock which protects concurrent manipulations of the rproc + * @dbg_dir: debugfs directory of this rproc device + * @traces: list of trace buffers + * @num_traces: number of trace buffers + * @carveouts: list of physically contiguous memory allocations + * @mappings: list of iommu mappings we initiated, needed on shutdown + * @firmware_loading_complete: marks e/o asynchronous firmware loading + * @bootaddr: address of first instruction to boot rproc with (optional) + * @rvdevs: list of remote virtio devices + * @notifyids: idr for dynamically assigning rproc-wide unique notify ids + */ +struct rproc { + struct klist_node node; + struct iommu_domain *domain; + const char *name; + const char *firmware; + void *priv; + const struct rproc_ops *ops; + struct device *dev; + struct kref refcount; + atomic_t power; + unsigned int state; + struct mutex lock; + struct dentry *dbg_dir; + struct list_head traces; + int num_traces; + struct list_head carveouts; + struct list_head mappings; + struct completion firmware_loading_complete; + u32 bootaddr; + struct list_head rvdevs; + struct idr notifyids; +}; + +/* we currently support only two vrings per rvdev */ +#define RVDEV_NUM_VRINGS 2 + +/** + * struct rproc_vring - remoteproc vring state + * @va: virtual address + * @dma: dma address + * @len: length, in bytes + * @da: device address + * @align: vring alignment + * @notifyid: rproc-specific unique vring index + * @rvdev: remote vdev + * @vq: the virtqueue of this vring + */ +struct rproc_vring { + void *va; + dma_addr_t dma; + int len; + u32 da; + u32 align; + int notifyid; + struct rproc_vdev *rvdev; + struct virtqueue *vq; +}; + +/** + * struct rproc_vdev - remoteproc state for a supported virtio device + * @node: list node + * @rproc: the rproc handle + * @vdev: the virio device + * @vring: the vrings for this vdev + * @dfeatures: virtio device features + * @gfeatures: virtio guest features + */ +struct rproc_vdev { + struct list_head node; + struct rproc *rproc; + struct virtio_device vdev; + struct rproc_vring vring[RVDEV_NUM_VRINGS]; + unsigned long dfeatures; + unsigned long gfeatures; +}; + +struct rproc *rproc_get_by_name(const char *name); +void rproc_put(struct rproc *rproc); + +struct rproc *rproc_alloc(struct device *dev, const char *name, + const struct rproc_ops *ops, + const char *firmware, int len); +void rproc_free(struct rproc *rproc); +int rproc_register(struct rproc *rproc); +int rproc_unregister(struct rproc *rproc); + +int rproc_boot(struct rproc *rproc); +void rproc_shutdown(struct rproc *rproc); + +static inline struct rproc_vdev *vdev_to_rvdev(struct virtio_device *vdev) +{ + return container_of(vdev, struct rproc_vdev, vdev); +} + +static inline struct rproc *vdev_to_rproc(struct virtio_device *vdev) +{ + struct rproc_vdev *rvdev = vdev_to_rvdev(vdev); + + return rvdev->rproc; +} + +#endif /* REMOTEPROC_H */ diff --git a/include/linux/rpmsg.h b/include/linux/rpmsg.h new file mode 100644 index 00000000000..a8e50e44203 --- /dev/null +++ b/include/linux/rpmsg.h @@ -0,0 +1,326 @@ +/* + * Remote processor messaging + * + * Copyright (C) 2011 Texas Instruments, Inc. + * Copyright (C) 2011 Google, Inc. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name Texas Instruments nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +#ifndef _LINUX_RPMSG_H +#define _LINUX_RPMSG_H + +#include <linux/types.h> +#include <linux/device.h> +#include <linux/mod_devicetable.h> + +/* The feature bitmap for virtio rpmsg */ +#define VIRTIO_RPMSG_F_NS 0 /* RP supports name service notifications */ + +/** + * struct rpmsg_hdr - common header for all rpmsg messages + * @src: source address + * @dst: destination address + * @reserved: reserved for future use + * @len: length of payload (in bytes) + * @flags: message flags + * @data: @len bytes of message payload data + * + * Every message sent(/received) on the rpmsg bus begins with this header. + */ +struct rpmsg_hdr { + u32 src; + u32 dst; + u32 reserved; + u16 len; + u16 flags; + u8 data[0]; +} __packed; + +/** + * struct rpmsg_ns_msg - dynamic name service announcement message + * @name: name of remote service that is published + * @addr: address of remote service that is published + * @flags: indicates whether service is created or destroyed + * + * This message is sent across to publish a new service, or announce + * about its removal. When we receive these messages, an appropriate + * rpmsg channel (i.e device) is created/destroyed. In turn, the ->probe() + * or ->remove() handler of the appropriate rpmsg driver will be invoked + * (if/as-soon-as one is registered). + */ +struct rpmsg_ns_msg { + char name[RPMSG_NAME_SIZE]; + u32 addr; + u32 flags; +} __packed; + +/** + * enum rpmsg_ns_flags - dynamic name service announcement flags + * + * @RPMSG_NS_CREATE: a new remote service was just created + * @RPMSG_NS_DESTROY: a known remote service was just destroyed + */ +enum rpmsg_ns_flags { + RPMSG_NS_CREATE = 0, + RPMSG_NS_DESTROY = 1, +}; + +#define RPMSG_ADDR_ANY 0xFFFFFFFF + +struct virtproc_info; + +/** + * rpmsg_channel - devices that belong to the rpmsg bus are called channels + * @vrp: the remote processor this channel belongs to + * @dev: the device struct + * @id: device id (used to match between rpmsg drivers and devices) + * @src: local address + * @dst: destination address + * @ept: the rpmsg endpoint of this channel + * @announce: if set, rpmsg will announce the creation/removal of this channel + */ +struct rpmsg_channel { + struct virtproc_info *vrp; + struct device dev; + struct rpmsg_device_id id; + u32 src; + u32 dst; + struct rpmsg_endpoint *ept; + bool announce; +}; + +typedef void (*rpmsg_rx_cb_t)(struct rpmsg_channel *, void *, int, void *, u32); + +/** + * struct rpmsg_endpoint - binds a local rpmsg address to its user + * @rpdev: rpmsg channel device + * @cb: rx callback handler + * @addr: local rpmsg address + * @priv: private data for the driver's use + * + * In essence, an rpmsg endpoint represents a listener on the rpmsg bus, as + * it binds an rpmsg address with an rx callback handler. + * + * Simple rpmsg drivers shouldn't use this struct directly, because + * things just work: every rpmsg driver provides an rx callback upon + * registering to the bus, and that callback is then bound to its rpmsg + * address when the driver is probed. When relevant inbound messages arrive + * (i.e. messages which their dst address equals to the src address of + * the rpmsg channel), the driver's handler is invoked to process it. + * + * More complicated drivers though, that do need to allocate additional rpmsg + * addresses, and bind them to different rx callbacks, must explicitly + * create additional endpoints by themselves (see rpmsg_create_ept()). + */ +struct rpmsg_endpoint { + struct rpmsg_channel *rpdev; + rpmsg_rx_cb_t cb; + u32 addr; + void *priv; +}; + +/** + * struct rpmsg_driver - rpmsg driver struct + * @drv: underlying device driver + * @id_table: rpmsg ids serviced by this driver + * @probe: invoked when a matching rpmsg channel (i.e. device) is found + * @remove: invoked when the rpmsg channel is removed + * @callback: invoked when an inbound message is received on the channel + */ +struct rpmsg_driver { + struct device_driver drv; + const struct rpmsg_device_id *id_table; + int (*probe)(struct rpmsg_channel *dev); + void (*remove)(struct rpmsg_channel *dev); + void (*callback)(struct rpmsg_channel *, void *, int, void *, u32); +}; + +int register_rpmsg_device(struct rpmsg_channel *dev); +void unregister_rpmsg_device(struct rpmsg_channel *dev); +int register_rpmsg_driver(struct rpmsg_driver *drv); +void unregister_rpmsg_driver(struct rpmsg_driver *drv); +void rpmsg_destroy_ept(struct rpmsg_endpoint *); +struct rpmsg_endpoint *rpmsg_create_ept(struct rpmsg_channel *, + rpmsg_rx_cb_t cb, void *priv, u32 addr); +int +rpmsg_send_offchannel_raw(struct rpmsg_channel *, u32, u32, void *, int, bool); + +/** + * rpmsg_send() - send a message across to the remote processor + * @rpdev: the rpmsg channel + * @data: payload of message + * @len: length of payload + * + * This function sends @data of length @len on the @rpdev channel. + * The message will be sent to the remote processor which the @rpdev + * channel belongs to, using @rpdev's source and destination addresses. + * In case there are no TX buffers available, the function will block until + * one becomes available, or a timeout of 15 seconds elapses. When the latter + * happens, -ERESTARTSYS is returned. + * + * Can only be called from process context (for now). + * + * Returns 0 on success and an appropriate error value on failure. + */ +static inline int rpmsg_send(struct rpmsg_channel *rpdev, void *data, int len) +{ + u32 src = rpdev->src, dst = rpdev->dst; + + return rpmsg_send_offchannel_raw(rpdev, src, dst, data, len, true); +} + +/** + * rpmsg_sendto() - send a message across to the remote processor, specify dst + * @rpdev: the rpmsg channel + * @data: payload of message + * @len: length of payload + * @dst: destination address + * + * This function sends @data of length @len to the remote @dst address. + * The message will be sent to the remote processor which the @rpdev + * channel belongs to, using @rpdev's source address. + * In case there are no TX buffers available, the function will block until + * one becomes available, or a timeout of 15 seconds elapses. When the latter + * happens, -ERESTARTSYS is returned. + * + * Can only be called from process context (for now). + * + * Returns 0 on success and an appropriate error value on failure. + */ +static inline +int rpmsg_sendto(struct rpmsg_channel *rpdev, void *data, int len, u32 dst) +{ + u32 src = rpdev->src; + + return rpmsg_send_offchannel_raw(rpdev, src, dst, data, len, true); +} + +/** + * rpmsg_send_offchannel() - send a message using explicit src/dst addresses + * @rpdev: the rpmsg channel + * @src: source address + * @dst: destination address + * @data: payload of message + * @len: length of payload + * + * This function sends @data of length @len to the remote @dst address, + * and uses @src as the source address. + * The message will be sent to the remote processor which the @rpdev + * channel belongs to. + * In case there are no TX buffers available, the function will block until + * one becomes available, or a timeout of 15 seconds elapses. When the latter + * happens, -ERESTARTSYS is returned. + * + * Can only be called from process context (for now). + * + * Returns 0 on success and an appropriate error value on failure. + */ +static inline +int rpmsg_send_offchannel(struct rpmsg_channel *rpdev, u32 src, u32 dst, + void *data, int len) +{ + return rpmsg_send_offchannel_raw(rpdev, src, dst, data, len, true); +} + +/** + * rpmsg_send() - send a message across to the remote processor + * @rpdev: the rpmsg channel + * @data: payload of message + * @len: length of payload + * + * This function sends @data of length @len on the @rpdev channel. + * The message will be sent to the remote processor which the @rpdev + * channel belongs to, using @rpdev's source and destination addresses. + * In case there are no TX buffers available, the function will immediately + * return -ENOMEM without waiting until one becomes available. + * + * Can only be called from process context (for now). + * + * Returns 0 on success and an appropriate error value on failure. + */ +static inline +int rpmsg_trysend(struct rpmsg_channel *rpdev, void *data, int len) +{ + u32 src = rpdev->src, dst = rpdev->dst; + + return rpmsg_send_offchannel_raw(rpdev, src, dst, data, len, false); +} + +/** + * rpmsg_sendto() - send a message across to the remote processor, specify dst + * @rpdev: the rpmsg channel + * @data: payload of message + * @len: length of payload + * @dst: destination address + * + * This function sends @data of length @len to the remote @dst address. + * The message will be sent to the remote processor which the @rpdev + * channel belongs to, using @rpdev's source address. + * In case there are no TX buffers available, the function will immediately + * return -ENOMEM without waiting until one becomes available. + * + * Can only be called from process context (for now). + * + * Returns 0 on success and an appropriate error value on failure. + */ +static inline +int rpmsg_trysendto(struct rpmsg_channel *rpdev, void *data, int len, u32 dst) +{ + u32 src = rpdev->src; + + return rpmsg_send_offchannel_raw(rpdev, src, dst, data, len, false); +} + +/** + * rpmsg_send_offchannel() - send a message using explicit src/dst addresses + * @rpdev: the rpmsg channel + * @src: source address + * @dst: destination address + * @data: payload of message + * @len: length of payload + * + * This function sends @data of length @len to the remote @dst address, + * and uses @src as the source address. + * The message will be sent to the remote processor which the @rpdev + * channel belongs to. + * In case there are no TX buffers available, the function will immediately + * return -ENOMEM without waiting until one becomes available. + * + * Can only be called from process context (for now). + * + * Returns 0 on success and an appropriate error value on failure. + */ +static inline +int rpmsg_trysend_offchannel(struct rpmsg_channel *rpdev, u32 src, u32 dst, + void *data, int len) +{ + return rpmsg_send_offchannel_raw(rpdev, src, dst, data, len, false); +} + +#endif /* _LINUX_RPMSG_H */ diff --git a/include/linux/rtc.h b/include/linux/rtc.h index 93f4d035076..fcabfb4873c 100644 --- a/include/linux/rtc.h +++ b/include/linux/rtc.h @@ -202,7 +202,8 @@ struct rtc_device struct hrtimer pie_timer; /* sub second exp, so needs hrtimer */ int pie_enabled; struct work_struct irqwork; - + /* Some hardware can't support UIE mode */ + int uie_unsupported; #ifdef CONFIG_RTC_INTF_DEV_UIE_EMUL struct work_struct uie_task; diff --git a/include/linux/rwsem.h b/include/linux/rwsem.h index 63d40655439..54bd7cd7ecb 100644 --- a/include/linux/rwsem.h +++ b/include/linux/rwsem.h @@ -14,7 +14,6 @@ #include <linux/list.h> #include <linux/spinlock.h> -#include <asm/system.h> #include <linux/atomic.h> struct rw_semaphore; diff --git a/include/linux/sa11x0-dma.h b/include/linux/sa11x0-dma.h new file mode 100644 index 00000000000..65839a58b8e --- /dev/null +++ b/include/linux/sa11x0-dma.h @@ -0,0 +1,24 @@ +/* + * SA11x0 DMA Engine support + * + * Copyright (C) 2012 Russell King + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef __LINUX_SA11X0_DMA_H +#define __LINUX_SA11X0_DMA_H + +struct dma_chan; + +#if defined(CONFIG_DMA_SA11X0) || defined(CONFIG_DMA_SA11X0_MODULE) +bool sa11x0_dma_filter_fn(struct dma_chan *, void *); +#else +static inline bool sa11x0_dma_filter_fn(struct dma_chan *c, void *d) +{ + return false; +} +#endif + +#endif diff --git a/include/linux/sched.h b/include/linux/sched.h index 0c3854b0d4b..81a173c0897 100644 --- a/include/linux/sched.h +++ b/include/linux/sched.h @@ -63,7 +63,6 @@ struct sched_param { #include <linux/nodemask.h> #include <linux/mm_types.h> -#include <asm/system.h> #include <asm/page.h> #include <asm/ptrace.h> #include <asm/cputime.h> diff --git a/include/linux/sh_clk.h b/include/linux/sh_clk.h index 54341d81168..0a9d8f2ac51 100644 --- a/include/linux/sh_clk.h +++ b/include/linux/sh_clk.h @@ -18,7 +18,8 @@ struct clk_mapping { struct kref ref; }; -struct clk_ops { + +struct sh_clk_ops { #ifdef CONFIG_SH_CLK_CPG_LEGACY void (*init)(struct clk *clk); #endif @@ -37,7 +38,7 @@ struct clk { unsigned short parent_num; /* choose between */ unsigned char src_shift; /* source clock field in the */ unsigned char src_width; /* configuration register */ - struct clk_ops *ops; + struct sh_clk_ops *ops; struct list_head children; struct list_head sibling; /* node for children */ diff --git a/include/linux/sh_intc.h b/include/linux/sh_intc.h index b160645f559..6aed0805927 100644 --- a/include/linux/sh_intc.h +++ b/include/linux/sh_intc.h @@ -3,6 +3,23 @@ #include <linux/ioport.h> +#ifdef CONFIG_SUPERH +#define INTC_NR_IRQS 512 +#else +#define INTC_NR_IRQS 1024 +#endif + +/* + * Convert back and forth between INTEVT and IRQ values. + */ +#ifdef CONFIG_CPU_HAS_INTEVT +#define evt2irq(evt) (((evt) >> 5) - 16) +#define irq2evt(irq) (((irq) + 16) << 5) +#else +#define evt2irq(evt) (evt) +#define irq2evt(irq) (irq) +#endif + typedef unsigned char intc_enum; struct intc_vect { diff --git a/include/linux/skbuff.h b/include/linux/skbuff.h index 3fcb204a261..33370271b8b 100644 --- a/include/linux/skbuff.h +++ b/include/linux/skbuff.h @@ -501,7 +501,6 @@ struct sk_buff { */ #include <linux/slab.h> -#include <asm/system.h> /* * skb might have a dst pointer attached, refcounted or not. @@ -1245,7 +1244,7 @@ static inline void skb_fill_page_desc(struct sk_buff *skb, int i, } extern void skb_add_rx_frag(struct sk_buff *skb, int i, struct page *page, - int off, int size); + int off, int size, unsigned int truesize); #define SKB_PAGE_ASSERT(skb) BUG_ON(skb_shinfo(skb)->nr_frags) #define SKB_FRAG_ASSERT(skb) BUG_ON(skb_has_frag_list(skb)) diff --git a/include/linux/slab.h b/include/linux/slab.h index 573c809c33d..a595dce6b0c 100644 --- a/include/linux/slab.h +++ b/include/linux/slab.h @@ -190,7 +190,7 @@ size_t ksize(const void *); #endif /** - * kcalloc - allocate memory for an array. The memory is set to zero. + * kmalloc_array - allocate memory for an array. * @n: number of elements. * @size: element size. * @flags: the type of memory to allocate. @@ -240,11 +240,22 @@ size_t ksize(const void *); * for general use, and so are not documented here. For a full list of * potential flags, always refer to linux/gfp.h. */ -static inline void *kcalloc(size_t n, size_t size, gfp_t flags) +static inline void *kmalloc_array(size_t n, size_t size, gfp_t flags) { if (size != 0 && n > ULONG_MAX / size) return NULL; - return __kmalloc(n * size, flags | __GFP_ZERO); + return __kmalloc(n * size, flags); +} + +/** + * kcalloc - allocate memory for an array. The memory is set to zero. + * @n: number of elements. + * @size: element size. + * @flags: the type of memory to allocate (see kmalloc). + */ +static inline void *kcalloc(size_t n, size_t size, gfp_t flags) +{ + return kmalloc_array(n, size, flags | __GFP_ZERO); } #if !defined(CONFIG_NUMA) && !defined(CONFIG_SLOB) diff --git a/include/linux/slub_def.h b/include/linux/slub_def.h index ca122b36aec..c2f8c8bc56e 100644 --- a/include/linux/slub_def.h +++ b/include/linux/slub_def.h @@ -22,7 +22,7 @@ enum stat_item { FREE_FROZEN, /* Freeing to frozen slab */ FREE_ADD_PARTIAL, /* Freeing moves slab to partial list */ FREE_REMOVE_PARTIAL, /* Freeing removes last object */ - ALLOC_FROM_PARTIAL, /* Cpu slab acquired from partial list */ + ALLOC_FROM_PARTIAL, /* Cpu slab acquired from node partial list */ ALLOC_SLAB, /* Cpu slab acquired from page allocator */ ALLOC_REFILL, /* Refill cpu slab from slab freelist */ ALLOC_NODE_MISMATCH, /* Switching cpu slab */ @@ -38,7 +38,9 @@ enum stat_item { CMPXCHG_DOUBLE_CPU_FAIL,/* Failure of this_cpu_cmpxchg_double */ CMPXCHG_DOUBLE_FAIL, /* Number of times that cmpxchg double did not match */ CPU_PARTIAL_ALLOC, /* Used cpu partial on alloc */ - CPU_PARTIAL_FREE, /* USed cpu partial on free */ + CPU_PARTIAL_FREE, /* Refill cpu partial on free */ + CPU_PARTIAL_NODE, /* Refill cpu partial from node partial */ + CPU_PARTIAL_DRAIN, /* Drain cpu partial to node partial */ NR_SLUB_STAT_ITEMS }; struct kmem_cache_cpu { diff --git a/include/linux/smp.h b/include/linux/smp.h index 8cc38d3bab0..10530d92c04 100644 --- a/include/linux/smp.h +++ b/include/linux/smp.h @@ -102,6 +102,22 @@ static inline void call_function_init(void) { } int on_each_cpu(smp_call_func_t func, void *info, int wait); /* + * Call a function on processors specified by mask, which might include + * the local one. + */ +void on_each_cpu_mask(const struct cpumask *mask, smp_call_func_t func, + void *info, bool wait); + +/* + * Call a function on each processor for which the supplied function + * cond_func returns a positive value. This may include the local + * processor. + */ +void on_each_cpu_cond(bool (*cond_func)(int cpu, void *info), + smp_call_func_t func, void *info, bool wait, + gfp_t gfp_flags); + +/* * Mark the boot cpu "online" so that it can call console drivers in * printk() and can access its per-cpu storage. */ @@ -132,6 +148,36 @@ static inline int up_smp_call_function(smp_call_func_t func, void *info) local_irq_enable(); \ 0; \ }) +/* + * Note we still need to test the mask even for UP + * because we actually can get an empty mask from + * code that on SMP might call us without the local + * CPU in the mask. + */ +#define on_each_cpu_mask(mask, func, info, wait) \ + do { \ + if (cpumask_test_cpu(0, (mask))) { \ + local_irq_disable(); \ + (func)(info); \ + local_irq_enable(); \ + } \ + } while (0) +/* + * Preemption is disabled here to make sure the cond_func is called under the + * same condtions in UP and SMP. + */ +#define on_each_cpu_cond(cond_func, func, info, wait, gfp_flags)\ + do { \ + void *__info = (info); \ + preempt_disable(); \ + if ((cond_func)(0, __info)) { \ + local_irq_disable(); \ + (func)(__info); \ + local_irq_enable(); \ + } \ + preempt_enable(); \ + } while (0) + static inline void smp_send_reschedule(int cpu) { } #define num_booting_cpus() 1 #define smp_prepare_boot_cpu() do {} while (0) diff --git a/include/linux/spi/orion_spi.h b/include/linux/spi/orion_spi.h index decf6d8c77b..b4d9fa6f797 100644 --- a/include/linux/spi/orion_spi.h +++ b/include/linux/spi/orion_spi.h @@ -11,7 +11,6 @@ struct orion_spi_info { u32 tclk; /* no <linux/clk.h> support yet */ - u32 enable_clock_fix; }; diff --git a/include/linux/spi/s3c24xx.h b/include/linux/spi/s3c24xx.h new file mode 100644 index 00000000000..c23b923e493 --- /dev/null +++ b/include/linux/spi/s3c24xx.h @@ -0,0 +1,26 @@ +/* + * Copyright (c) 2006 Simtec Electronics + * Ben Dooks <ben@simtec.co.uk> + * + * S3C2410 - SPI Controller platform_device info + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#ifndef __LINUX_SPI_S3C24XX_H +#define __LINUX_SPI_S3C24XX_H __FILE__ + +struct s3c2410_spi_info { + int pin_cs; /* simple gpio cs */ + unsigned int num_cs; /* total chipselects */ + int bus_num; /* bus number to use. */ + + unsigned int use_fiq:1; /* use fiq */ + + void (*gpio_setup)(struct s3c2410_spi_info *spi, int enable); + void (*set_cs)(struct s3c2410_spi_info *spi, int cs, int pol); +}; + +#endif /* __LINUX_SPI_S3C24XX_H */ diff --git a/include/linux/spinlock.h b/include/linux/spinlock.h index 36323908726..7d537ced949 100644 --- a/include/linux/spinlock.h +++ b/include/linux/spinlock.h @@ -55,8 +55,8 @@ #include <linux/kernel.h> #include <linux/stringify.h> #include <linux/bottom_half.h> +#include <asm/barrier.h> -#include <asm/system.h> /* * Must define these before including other files, inline functions need them diff --git a/include/linux/spinlock_api_smp.h b/include/linux/spinlock_api_smp.h index e253ccd7a60..51df117abe4 100644 --- a/include/linux/spinlock_api_smp.h +++ b/include/linux/spinlock_api_smp.h @@ -67,7 +67,7 @@ _raw_spin_unlock_irqrestore(raw_spinlock_t *lock, unsigned long flags) #define _raw_spin_trylock_bh(lock) __raw_spin_trylock_bh(lock) #endif -#ifdef CONFIG_INLINE_SPIN_UNLOCK +#ifndef CONFIG_UNINLINE_SPIN_UNLOCK #define _raw_spin_unlock(lock) __raw_spin_unlock(lock) #endif diff --git a/include/linux/stop_machine.h b/include/linux/stop_machine.h index c170edc3bf5..3b5e910d14c 100644 --- a/include/linux/stop_machine.h +++ b/include/linux/stop_machine.h @@ -5,7 +5,6 @@ #include <linux/cpumask.h> #include <linux/smp.h> #include <linux/list.h> -#include <asm/system.h> /* * stop_cpu[s]() is simplistic per-cpu maximum priority cpu diff --git a/include/linux/sunrpc/svc_rdma.h b/include/linux/sunrpc/svc_rdma.h index c14fe86dac5..0b8e3e6bdac 100644 --- a/include/linux/sunrpc/svc_rdma.h +++ b/include/linux/sunrpc/svc_rdma.h @@ -190,7 +190,7 @@ extern int svc_rdma_xdr_encode_error(struct svcxprt_rdma *, extern void svc_rdma_xdr_encode_write_list(struct rpcrdma_msg *, int); extern void svc_rdma_xdr_encode_reply_array(struct rpcrdma_write_array *, int); extern void svc_rdma_xdr_encode_array_chunk(struct rpcrdma_write_array *, int, - u32, u64, u32); + __be32, __be64, u32); extern void svc_rdma_xdr_encode_reply_header(struct svcxprt_rdma *, struct rpcrdma_msg *, struct rpcrdma_msg *, @@ -292,7 +292,7 @@ svc_rdma_get_reply_array(struct rpcrdma_msg *rmsgp) if (wr_ary) { rp_ary = (struct rpcrdma_write_array *) &wr_ary-> - wc_array[wr_ary->wc_nchunks].wc_target.rs_length; + wc_array[ntohl(wr_ary->wc_nchunks)].wc_target.rs_length; goto found_it; } diff --git a/include/linux/swap.h b/include/linux/swap.h index b86b5c20617..8dc0ea7caf0 100644 --- a/include/linux/swap.h +++ b/include/linux/swap.h @@ -21,6 +21,9 @@ struct bio; #define SWAP_FLAG_PRIO_SHIFT 0 #define SWAP_FLAG_DISCARD 0x10000 /* discard swap cluster after use */ +#define SWAP_FLAGS_VALID (SWAP_FLAG_PRIO_MASK | SWAP_FLAG_PREFER | \ + SWAP_FLAG_DISCARD) + static inline int current_is_kswapd(void) { return current->flags & PF_KSWAPD; diff --git a/include/linux/sysinfo.h b/include/linux/sysinfo.h new file mode 100644 index 00000000000..934335a2252 --- /dev/null +++ b/include/linux/sysinfo.h @@ -0,0 +1,24 @@ +#ifndef _LINUX_SYSINFO_H +#define _LINUX_SYSINFO_H + +#include <linux/types.h> + +#define SI_LOAD_SHIFT 16 +struct sysinfo { + __kernel_long_t uptime; /* Seconds since boot */ + __kernel_ulong_t loads[3]; /* 1, 5, and 15 minute load averages */ + __kernel_ulong_t totalram; /* Total usable main memory size */ + __kernel_ulong_t freeram; /* Available memory size */ + __kernel_ulong_t sharedram; /* Amount of shared memory */ + __kernel_ulong_t bufferram; /* Memory used by buffers */ + __kernel_ulong_t totalswap; /* Total swap space size */ + __kernel_ulong_t freeswap; /* swap space still available */ + __u16 procs; /* Number of current processes */ + __u16 pad; /* Explicit padding for m68k */ + __kernel_ulong_t totalhigh; /* Total high memory size */ + __kernel_ulong_t freehigh; /* Available high memory size */ + __u32 mem_unit; /* Memory unit size in bytes */ + char _f[20-2*sizeof(__kernel_ulong_t)-sizeof(__u32)]; /* Padding: libc5 uses this.. */ +}; + +#endif /* _LINUX_SYSINFO_H */ diff --git a/include/linux/tboot.h b/include/linux/tboot.h index 1dba6ee5520..c75128bed5f 100644 --- a/include/linux/tboot.h +++ b/include/linux/tboot.h @@ -143,7 +143,6 @@ static inline int tboot_enabled(void) extern void tboot_probe(void); extern void tboot_shutdown(u32 shutdown_type); -extern void tboot_sleep(u8 sleep_state, u32 pm1a_control, u32 pm1b_control); extern struct acpi_table_header *tboot_get_dmar_table( struct acpi_table_header *dmar_tbl); extern int tboot_force_iommu(void); diff --git a/include/linux/time.h b/include/linux/time.h index b3061782dec..33a92ead4d8 100644 --- a/include/linux/time.h +++ b/include/linux/time.h @@ -116,7 +116,6 @@ static inline struct timespec timespec_sub(struct timespec lhs, extern void read_persistent_clock(struct timespec *ts); extern void read_boot_clock(struct timespec *ts); extern int update_persistent_clock(struct timespec now); -extern int no_sync_cmos_clock __read_mostly; void timekeeping_init(void); extern int timekeeping_suspended; @@ -256,6 +255,7 @@ static __always_inline void timespec_add_ns(struct timespec *a, u64 ns) a->tv_sec += __iter_div_u64_rem(a->tv_nsec + ns, NSEC_PER_SEC, &ns); a->tv_nsec = ns; } + #endif /* __KERNEL__ */ #define NFDBITS __NFDBITS diff --git a/include/linux/timex.h b/include/linux/timex.h index b75e1864ed1..99bc88b1fc0 100644 --- a/include/linux/timex.h +++ b/include/linux/timex.h @@ -252,7 +252,7 @@ extern void ntp_clear(void); /* Returns how long ticks are at present, in ns / 2^NTP_SCALE_SHIFT. */ extern u64 ntp_tick_length(void); -extern void second_overflow(void); +extern int second_overflow(unsigned long secs); extern int do_adjtimex(struct timex *); extern void hardpps(const struct timespec *, const struct timespec *); diff --git a/include/linux/tty.h b/include/linux/tty.h index a91ff403b3b..9f47ab540f6 100644 --- a/include/linux/tty.h +++ b/include/linux/tty.h @@ -44,7 +44,6 @@ #include <linux/tty_ldisc.h> #include <linux/mutex.h> -#include <asm/system.h> /* diff --git a/include/linux/virtio.h b/include/linux/virtio.h index d0018d27c28..8efd28ae559 100644 --- a/include/linux/virtio.h +++ b/include/linux/virtio.h @@ -96,7 +96,6 @@ struct virtio_driver { void (*config_changed)(struct virtio_device *dev); #ifdef CONFIG_PM int (*freeze)(struct virtio_device *dev); - int (*thaw)(struct virtio_device *dev); int (*restore)(struct virtio_device *dev); #endif }; diff --git a/include/linux/virtio_ids.h b/include/linux/virtio_ids.h index c5d8455c68c..7529b854b7f 100644 --- a/include/linux/virtio_ids.h +++ b/include/linux/virtio_ids.h @@ -34,6 +34,7 @@ #define VIRTIO_ID_CONSOLE 3 /* virtio console */ #define VIRTIO_ID_RNG 4 /* virtio ring */ #define VIRTIO_ID_BALLOON 5 /* virtio balloon */ +#define VIRTIO_ID_RPMSG 7 /* virtio remote processor messaging */ #define VIRTIO_ID_SCSI 8 /* virtio scsi */ #define VIRTIO_ID_9P 9 /* 9p virtio console */ diff --git a/include/linux/wait.h b/include/linux/wait.h index 7d9a9e990ce..1dee81c41ff 100644 --- a/include/linux/wait.h +++ b/include/linux/wait.h @@ -22,7 +22,6 @@ #include <linux/list.h> #include <linux/stddef.h> #include <linux/spinlock.h> -#include <asm/system.h> #include <asm/current.h> typedef struct __wait_queue wait_queue_t; diff --git a/include/linux/watchdog.h b/include/linux/watchdog.h index 43ba5b3ce2a..ac40716b44e 100644 --- a/include/linux/watchdog.h +++ b/include/linux/watchdog.h @@ -66,6 +66,7 @@ struct watchdog_device; * @ping: The routine that sends a keepalive ping to the watchdog device. * @status: The routine that shows the status of the watchdog device. * @set_timeout:The routine for setting the watchdog devices timeout value. + * @get_timeleft:The routine that get's the time that's left before a reset. * @ioctl: The routines that handles extra ioctl calls. * * The watchdog_ops structure contains a list of low-level operations @@ -82,6 +83,7 @@ struct watchdog_ops { int (*ping)(struct watchdog_device *); unsigned int (*status)(struct watchdog_device *); int (*set_timeout)(struct watchdog_device *, unsigned int); + unsigned int (*get_timeleft)(struct watchdog_device *); long (*ioctl)(struct watchdog_device *, unsigned int, unsigned long); }; @@ -127,7 +129,7 @@ struct watchdog_device { #endif /* Use the following function to set the nowayout feature */ -static inline void watchdog_set_nowayout(struct watchdog_device *wdd, int nowayout) +static inline void watchdog_set_nowayout(struct watchdog_device *wdd, bool nowayout) { if (nowayout) set_bit(WDOG_NO_WAY_OUT, &wdd->status); diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 248fb05feb6..83d800c31e3 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -620,8 +620,10 @@ struct sta_bss_parameters { * @llid: mesh local link id * @plid: mesh peer link id * @plink_state: mesh peer link state - * @signal: signal strength of last received packet in dBm - * @signal_avg: signal strength average in dBm + * @signal: the signal strength, type depends on the wiphy's signal_type + NOTE: For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_. + * @signal_avg: avg signal strength, type depends on the wiphy's signal_type + NOTE: For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_. * @txrate: current unicast bitrate from this station * @rxrate: current unicast bitrate to this station * @rx_packets: packets received from this station diff --git a/include/net/netfilter/nf_conntrack_l4proto.h b/include/net/netfilter/nf_conntrack_l4proto.h index 90c67c7db7e..3b572bb20aa 100644 --- a/include/net/netfilter/nf_conntrack_l4proto.h +++ b/include/net/netfilter/nf_conntrack_l4proto.h @@ -118,6 +118,10 @@ extern struct nf_conntrack_l4proto nf_conntrack_l4proto_generic; extern struct nf_conntrack_l4proto * __nf_ct_l4proto_find(u_int16_t l3proto, u_int8_t l4proto); +extern struct nf_conntrack_l4proto * +nf_ct_l4proto_find_get(u_int16_t l3proto, u_int8_t l4proto); +extern void nf_ct_l4proto_put(struct nf_conntrack_l4proto *p); + /* Protocol registration. */ extern int nf_conntrack_l4proto_register(struct nf_conntrack_l4proto *proto); extern void nf_conntrack_l4proto_unregister(struct nf_conntrack_l4proto *proto); diff --git a/include/net/netfilter/nf_conntrack_timeout.h b/include/net/netfilter/nf_conntrack_timeout.h index 0e04db4a086..34ec89f8dbf 100644 --- a/include/net/netfilter/nf_conntrack_timeout.h +++ b/include/net/netfilter/nf_conntrack_timeout.h @@ -15,7 +15,7 @@ struct ctnl_timeout { atomic_t refcnt; char name[CTNL_TIMEOUT_NAME_MAX]; __u16 l3num; - __u8 l4num; + struct nf_conntrack_l4proto *l4proto; char data[0]; }; diff --git a/include/scsi/iscsi_if.h b/include/scsi/iscsi_if.h index 9c23ee8fd2d..917741bb8e1 100644 --- a/include/scsi/iscsi_if.h +++ b/include/scsi/iscsi_if.h @@ -261,7 +261,8 @@ struct iscsi_uevent { } host_event; struct msg_ping_comp { uint32_t host_no; - uint32_t status; + uint32_t status; /* enum + * iscsi_ping_status_code */ uint32_t pid; /* unique ping id associated with each ping request */ uint32_t data_size; @@ -483,6 +484,20 @@ enum iscsi_port_state { ISCSI_PORT_STATE_UP = 0x2, }; +/* iSCSI PING status/error code */ +enum iscsi_ping_status_code { + ISCSI_PING_SUCCESS = 0, + ISCSI_PING_FW_DISABLED = 0x1, + ISCSI_PING_IPADDR_INVALID = 0x2, + ISCSI_PING_LINKLOCAL_IPV6_ADDR_INVALID = 0x3, + ISCSI_PING_TIMEOUT = 0x4, + ISCSI_PING_INVALID_DEST_ADDR = 0x5, + ISCSI_PING_OVERSIZE_PACKET = 0x6, + ISCSI_PING_ICMP_ERROR = 0x7, + ISCSI_PING_MAX_REQ_EXCEEDED = 0x8, + ISCSI_PING_NO_ARP_RECEIVED = 0x9, +}; + #define iscsi_ptr(_handle) ((void*)(unsigned long)_handle) #define iscsi_handle(_ptr) ((uint64_t)(unsigned long)_ptr) @@ -578,6 +593,6 @@ struct iscsi_chap_rec { char username[ISCSI_CHAP_AUTH_NAME_MAX_LEN]; uint8_t password[ISCSI_CHAP_AUTH_SECRET_MAX_LEN]; uint8_t password_length; -} __packed; +}; #endif diff --git a/include/scsi/libfcoe.h b/include/scsi/libfcoe.h index 5a35a2a2d3c..cfdb55f0937 100644 --- a/include/scsi/libfcoe.h +++ b/include/scsi/libfcoe.h @@ -165,7 +165,8 @@ struct fcoe_ctlr { * @switch_name: WWN of switch from advertisement * @fabric_name: WWN of fabric from advertisement * @fc_map: FC_MAP value from advertisement - * @fcf_mac: Ethernet address of the FCF + * @fcf_mac: Ethernet address of the FCF for FIP traffic + * @fcoe_mac: Ethernet address of the FCF for FCoE traffic * @vfid: virtual fabric ID * @pri: selection priority, smaller values are better * @flogi_sent: current FLOGI sent to this FCF @@ -188,6 +189,7 @@ struct fcoe_fcf { u32 fc_map; u16 vfid; u8 fcf_mac[ETH_ALEN]; + u8 fcoe_mac[ETH_ALEN]; u8 pri; u8 flogi_sent; diff --git a/include/trace/events/btrfs.h b/include/trace/events/btrfs.h index 84f3001a568..91b91e80567 100644 --- a/include/trace/events/btrfs.h +++ b/include/trace/events/btrfs.h @@ -6,6 +6,7 @@ #include <linux/writeback.h> #include <linux/tracepoint.h> +#include <trace/events/gfpflags.h> struct btrfs_root; struct btrfs_fs_info; @@ -862,6 +863,49 @@ TRACE_EVENT(btrfs_setup_cluster, __entry->size, __entry->max_size, __entry->bitmap) ); +struct extent_state; +TRACE_EVENT(alloc_extent_state, + + TP_PROTO(struct extent_state *state, gfp_t mask, unsigned long IP), + + TP_ARGS(state, mask, IP), + + TP_STRUCT__entry( + __field(struct extent_state *, state) + __field(gfp_t, mask) + __field(unsigned long, ip) + ), + + TP_fast_assign( + __entry->state = state, + __entry->mask = mask, + __entry->ip = IP + ), + + TP_printk("state=%p; mask = %s; caller = %pF", __entry->state, + show_gfp_flags(__entry->mask), (void *)__entry->ip) +); + +TRACE_EVENT(free_extent_state, + + TP_PROTO(struct extent_state *state, unsigned long IP), + + TP_ARGS(state, IP), + + TP_STRUCT__entry( + __field(struct extent_state *, state) + __field(unsigned long, ip) + ), + + TP_fast_assign( + __entry->state = state, + __entry->ip = IP + ), + + TP_printk(" state=%p; caller = %pF", __entry->state, + (void *)__entry->ip) +); + #endif /* _TRACE_BTRFS_H */ /* This part must be outside protection */ diff --git a/include/trace/events/jbd2.h b/include/trace/events/jbd2.h index 75964412ddb..127993dbf32 100644 --- a/include/trace/events/jbd2.h +++ b/include/trace/events/jbd2.h @@ -81,6 +81,13 @@ DEFINE_EVENT(jbd2_commit, jbd2_commit_logging, TP_ARGS(journal, commit_transaction) ); +DEFINE_EVENT(jbd2_commit, jbd2_drop_transaction, + + TP_PROTO(journal_t *journal, transaction_t *commit_transaction), + + TP_ARGS(journal, commit_transaction) +); + TRACE_EVENT(jbd2_end_commit, TP_PROTO(journal_t *journal, transaction_t *commit_transaction), @@ -200,7 +207,7 @@ TRACE_EVENT(jbd2_checkpoint_stats, __entry->forced_to_close, __entry->written, __entry->dropped) ); -TRACE_EVENT(jbd2_cleanup_journal_tail, +TRACE_EVENT(jbd2_update_log_tail, TP_PROTO(journal_t *journal, tid_t first_tid, unsigned long block_nr, unsigned long freed), @@ -229,6 +236,26 @@ TRACE_EVENT(jbd2_cleanup_journal_tail, __entry->block_nr, __entry->freed) ); +TRACE_EVENT(jbd2_write_superblock, + + TP_PROTO(journal_t *journal, int write_op), + + TP_ARGS(journal, write_op), + + TP_STRUCT__entry( + __field( dev_t, dev ) + __field( int, write_op ) + ), + + TP_fast_assign( + __entry->dev = journal->j_fs_dev->bd_dev; + __entry->write_op = write_op; + ), + + TP_printk("dev %d,%d write_op %x", MAJOR(__entry->dev), + MINOR(__entry->dev), __entry->write_op) +); + #endif /* _TRACE_JBD2_H */ /* This part must be outside protection */ diff --git a/include/video/sa1100fb.h b/include/video/sa1100fb.h new file mode 100644 index 00000000000..4ab40965378 --- /dev/null +++ b/include/video/sa1100fb.h @@ -0,0 +1,63 @@ +/* + * StrongARM 1100 LCD Controller Frame Buffer Device + * + * Copyright (C) 1999 Eric A. Thomas + * Based on acornfb.c Copyright (C) Russell King. + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive + * for more details. + */ +#ifndef _VIDEO_SA1100FB_H +#define _VIDEO_SA1100FB_H + +#include <linux/fb.h> +#include <linux/types.h> + +#define RGB_4 0 +#define RGB_8 1 +#define RGB_16 2 +#define NR_RGB 3 + +/* These are the bitfields for each display depth that we support. */ +struct sa1100fb_rgb { + struct fb_bitfield red; + struct fb_bitfield green; + struct fb_bitfield blue; + struct fb_bitfield transp; +}; + +/* This structure describes the machine which we are running on. */ +struct sa1100fb_mach_info { + u_long pixclock; + + u_short xres; + u_short yres; + + u_char bpp; + u_char hsync_len; + u_char left_margin; + u_char right_margin; + + u_char vsync_len; + u_char upper_margin; + u_char lower_margin; + u_char sync; + + u_int cmap_greyscale:1, + cmap_inverse:1, + cmap_static:1, + unused:29; + + u_int lccr0; + u_int lccr3; + + /* Overrides for the default RGB maps */ + const struct sa1100fb_rgb *rgb[NR_RGB]; + + void (*backlight_power)(int); + void (*lcd_power)(int); + void (*set_visual)(u32); +}; + +#endif diff --git a/include/xen/xen-ops.h b/include/xen/xen-ops.h index 03c85d7387f..6a198e46ab6 100644 --- a/include/xen/xen-ops.h +++ b/include/xen/xen-ops.h @@ -23,6 +23,7 @@ int xen_create_contiguous_region(unsigned long vstart, unsigned int order, void xen_destroy_contiguous_region(unsigned long vstart, unsigned int order); +struct vm_area_struct; int xen_remap_domain_mfn_range(struct vm_area_struct *vma, unsigned long addr, unsigned long mfn, int nr, |