diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/linux/bcma/bcma.h | 1 | ||||
| -rw-r--r-- | include/linux/bcma/bcma_driver_chipcommon.h | 3 | ||||
| -rw-r--r-- | include/linux/bcma/bcma_regs.h | 1 | ||||
| -rw-r--r-- | include/linux/ieee80211.h | 30 | ||||
| -rw-r--r-- | include/linux/platform_data/brcmfmac-sdio.h | 124 | ||||
| -rw-r--r-- | include/net/cfg80211.h | 4 | ||||
| -rw-r--r-- | include/net/mac80211.h | 37 | ||||
| -rw-r--r-- | include/net/nfc/nfc.h | 2 | ||||
| -rw-r--r-- | include/uapi/linux/nfc.h | 7 | ||||
| -rw-r--r-- | include/uapi/linux/rfkill.h | 2 |
10 files changed, 196 insertions, 15 deletions
diff --git a/include/linux/bcma/bcma.h b/include/linux/bcma/bcma.h index 0ab6712fd76..f14a98a79c9 100644 --- a/include/linux/bcma/bcma.h +++ b/include/linux/bcma/bcma.h @@ -134,6 +134,7 @@ struct bcma_host_ops { #define BCMA_CORE_I2S 0x834 #define BCMA_CORE_SDR_DDR1_MEM_CTL 0x835 /* SDR/DDR1 memory controller core */ #define BCMA_CORE_SHIM 0x837 /* SHIM component in ubus/6362 */ +#define BCMA_CORE_ARM_CR4 0x83e #define BCMA_CORE_DEFAULT 0xFFF #define BCMA_MAX_NR_CORES 16 diff --git a/include/linux/bcma/bcma_driver_chipcommon.h b/include/linux/bcma/bcma_driver_chipcommon.h index 453fcc91468..b8b09eac60a 100644 --- a/include/linux/bcma/bcma_driver_chipcommon.h +++ b/include/linux/bcma/bcma_driver_chipcommon.h @@ -316,6 +316,9 @@ #define BCMA_CC_PMU_CTL 0x0600 /* PMU control */ #define BCMA_CC_PMU_CTL_ILP_DIV 0xFFFF0000 /* ILP div mask */ #define BCMA_CC_PMU_CTL_ILP_DIV_SHIFT 16 +#define BCMA_CC_PMU_CTL_RES 0x00006000 /* reset control mask */ +#define BCMA_CC_PMU_CTL_RES_SHIFT 13 +#define BCMA_CC_PMU_CTL_RES_RELOAD 0x2 /* reload POR values */ #define BCMA_CC_PMU_CTL_PLL_UPD 0x00000400 #define BCMA_CC_PMU_CTL_NOILPONW 0x00000200 /* No ILP on wait */ #define BCMA_CC_PMU_CTL_HTREQEN 0x00000100 /* HT req enable */ diff --git a/include/linux/bcma/bcma_regs.h b/include/linux/bcma/bcma_regs.h index 7e8104bb7a7..917dcd7965e 100644 --- a/include/linux/bcma/bcma_regs.h +++ b/include/linux/bcma/bcma_regs.h @@ -37,6 +37,7 @@ #define BCMA_IOST_BIST_DONE 0x8000 #define BCMA_RESET_CTL 0x0800 #define BCMA_RESET_CTL_RESET 0x0001 +#define BCMA_RESET_ST 0x0804 /* BCMA PCI config space registers. */ #define BCMA_PCI_PMCSR 0x44 diff --git a/include/linux/ieee80211.h b/include/linux/ieee80211.h index 4cf0c9e4dd9..e46fea8b972 100644 --- a/include/linux/ieee80211.h +++ b/include/linux/ieee80211.h @@ -1027,6 +1027,26 @@ enum ieee80211_p2p_attr_id { IEEE80211_P2P_ATTR_MAX }; +/* Notice of Absence attribute - described in P2P spec 4.1.14 */ +/* Typical max value used here */ +#define IEEE80211_P2P_NOA_DESC_MAX 4 + +struct ieee80211_p2p_noa_desc { + u8 count; + __le32 duration; + __le32 interval; + __le32 start_time; +} __packed; + +struct ieee80211_p2p_noa_attr { + u8 index; + u8 oppps_ctwindow; + struct ieee80211_p2p_noa_desc desc[IEEE80211_P2P_NOA_DESC_MAX]; +} __packed; + +#define IEEE80211_P2P_OPPPS_ENABLE_BIT BIT(7) +#define IEEE80211_P2P_OPPPS_CTWINDOW_MASK 0x7F + /** * struct ieee80211_bar - HT Block Ack Request * @@ -1935,6 +1955,16 @@ enum ieee80211_timeout_interval_type { WLAN_TIMEOUT_ASSOC_COMEBACK = 3 /* 802.11w */, }; +/** + * struct ieee80211_timeout_interval_ie - Timeout Interval element + * @type: type, see &enum ieee80211_timeout_interval_type + * @value: timeout interval value + */ +struct ieee80211_timeout_interval_ie { + u8 type; + __le32 value; +} __packed; + /* BACK action code */ enum ieee80211_back_actioncode { WLAN_ACTION_ADDBA_REQ = 0, diff --git a/include/linux/platform_data/brcmfmac-sdio.h b/include/linux/platform_data/brcmfmac-sdio.h new file mode 100644 index 00000000000..1ade657d5fc --- /dev/null +++ b/include/linux/platform_data/brcmfmac-sdio.h @@ -0,0 +1,124 @@ +/* + * Copyright (c) 2013 Broadcom Corporation + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY + * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION + * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN + * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + */ + +#ifndef _LINUX_BRCMFMAC_PLATFORM_H +#define _LINUX_BRCMFMAC_PLATFORM_H + +/* + * Platform specific driver functions and data. Through the platform specific + * device data functions can be provided to help the brcmfmac driver to + * operate with the device in combination with the used platform. + * + * Use the platform data in the following (similar) way: + * + * +#include <brcmfmac_platform.h> + + +static void brcmfmac_power_on(void) +{ +} + +static void brcmfmac_power_off(void) +{ +} + +static void brcmfmac_reset(void) +{ +} + +static struct brcmfmac_sdio_platform_data brcmfmac_sdio_pdata = { + .power_on = brcmfmac_power_on, + .power_off = brcmfmac_power_off, + .reset = brcmfmac_reset +}; + +static struct platform_device brcmfmac_device = { + .name = BRCMFMAC_SDIO_PDATA_NAME, + .id = PLATFORM_DEVID_NONE, + .dev.platform_data = &brcmfmac_sdio_pdata +}; + +void __init brcmfmac_init_pdata(void) +{ + brcmfmac_sdio_pdata.oob_irq_supported = true; + brcmfmac_sdio_pdata.oob_irq_nr = gpio_to_irq(GPIO_BRCMF_SDIO_OOB); + brcmfmac_sdio_pdata.oob_irq_flags = IORESOURCE_IRQ | + IORESOURCE_IRQ_HIGHLEVEL; + platform_device_register(&brcmfmac_device); +} + * + * + * Note: the brcmfmac can be loaded as module or be statically built-in into + * the kernel. If built-in then do note that it uses module_init (and + * module_exit) routines which equal device_initcall. So if you intend to + * create a module with the platform specific data for the brcmfmac and have + * it built-in to the kernel then use a higher initcall then device_initcall + * (see init.h). If this is not done then brcmfmac will load without problems + * but will not pickup the platform data. + * + * When the driver does not "detect" platform driver data then it will continue + * without reporting anything and just assume there is no data needed. Which is + * probably true for most platforms. + * + * Explanation of the platform_data fields: + * + * drive_strength: is the preferred drive_strength to be used for the SDIO + * pins. If 0 then a default value will be used. This is the target drive + * strength, the exact drive strength which will be used depends on the + * capabilities of the device. + * + * oob_irq_supported: does the board have support for OOB interrupts. SDIO + * in-band interrupts are relatively slow and for having less overhead on + * interrupt processing an out of band interrupt can be used. If the HW + * supports this then enable this by setting this field to true and configure + * the oob related fields. + * + * oob_irq_nr, oob_irq_flags: the OOB interrupt information. The values are + * used for registering the irq using request_irq function. + * + * power_on: This function is called by the brcmfmac when the module gets + * loaded. This can be particularly useful for low power devices. The platform + * spcific routine may for example decide to power up the complete device. + * If there is no use-case for this function then provide NULL. + * + * power_off: This function is called by the brcmfmac when the module gets + * unloaded. At this point the device can be powered down or otherwise be reset. + * So if an actual power_off is not supported but reset is then reset the device + * when this function gets called. This can be particularly useful for low power + * devices. If there is no use-case for this function (either power-down or + * reset) then provide NULL. + * + * reset: This function can get called if the device communication broke down. + * This functionality is particularly useful in case of SDIO type devices. It is + * possible to reset a dongle via sdio data interface, but it requires that + * this is fully functional. This function is chip/module specific and this + * function should return only after the complete reset has completed. + */ + +#define BRCMFMAC_SDIO_PDATA_NAME "brcmfmac_sdio" + +struct brcmfmac_sdio_platform_data { + unsigned int drive_strength; + bool oob_irq_supported; + unsigned int oob_irq_nr; + unsigned long oob_irq_flags; + void (*power_on)(void); + void (*power_off)(void); + void (*reset)(void); +}; + +#endif /* _LINUX_BRCMFMAC_PLATFORM_H */ diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index bdba9b61906..57870b64697 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -1998,6 +1998,10 @@ struct cfg80211_update_ft_ies_params { * advertise the support for MAC based ACL have to implement this callback. * * @start_radar_detection: Start radar detection in the driver. + * + * @update_ft_ies: Provide updated Fast BSS Transition information to the + * driver. If the SME is in the driver/firmware, this information can be + * used in building Authentication and Reassociation Request frames. */ struct cfg80211_ops { int (*suspend)(struct wiphy *wiphy, struct cfg80211_wowlan *wow); diff --git a/include/net/mac80211.h b/include/net/mac80211.h index dd73b8c6746..64faf015dd1 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -330,8 +330,7 @@ enum ieee80211_rssi_event { * @ssid_len: Length of SSID given in @ssid. * @hidden_ssid: The SSID of the current vif is hidden. Only valid in AP-mode. * @txpower: TX power in dBm - * @p2p_ctwindow: P2P CTWindow, only for P2P client interfaces - * @p2p_oppps: P2P opportunistic PS is enabled + * @p2p_noa_attr: P2P NoA attribute for P2P powersave */ struct ieee80211_bss_conf { const u8 *bssid; @@ -365,8 +364,7 @@ struct ieee80211_bss_conf { size_t ssid_len; bool hidden_ssid; int txpower; - u8 p2p_ctwindow; - bool p2p_oppps; + struct ieee80211_p2p_noa_attr p2p_noa_attr; }; /** @@ -976,8 +974,7 @@ enum ieee80211_smps_mode { * @power_level: requested transmit power (in dBm), backward compatibility * value only that is set to the minimum of all interfaces * - * @channel: the channel to tune to - * @channel_type: the channel (HT) type + * @chandef: the channel definition to tune to * @radar_enabled: whether radar detection is enabled * * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame @@ -1003,8 +1000,7 @@ struct ieee80211_conf { u8 long_frame_max_tx_count, short_frame_max_tx_count; - struct ieee80211_channel *channel; - enum nl80211_channel_type channel_type; + struct cfg80211_chan_def chandef; bool radar_enabled; enum ieee80211_smps_mode smps_mode; }; @@ -1536,6 +1532,17 @@ enum ieee80211_hw_flags { * @netdev_features: netdev features to be set in each netdev created * from this HW. Note only HW checksum features are currently * compatible with mac80211. Other feature bits will be rejected. + * + * @uapsd_queues: This bitmap is included in (re)association frame to indicate + * for each access category if it is uAPSD trigger-enabled and delivery- + * enabled. Use IEEE80211_WMM_IE_STA_QOSINFO_AC_* to set this bitmap. + * Each bit corresponds to different AC. Value '1' in specific bit means + * that corresponding AC is both trigger- and delivery-enabled. '0' means + * neither enabled. + * + * @uapsd_max_sp_len: maximum number of total buffered frames the WMM AP may + * deliver to a WMM STA during any Service Period triggered by the WMM STA. + * Use IEEE80211_WMM_IE_STA_QOSINFO_SP_* for correct values. */ struct ieee80211_hw { struct ieee80211_conf conf; @@ -1561,6 +1568,8 @@ struct ieee80211_hw { u8 radiotap_mcs_details; u16 radiotap_vht_details; netdev_features_t netdev_features; + u8 uapsd_queues; + u8 uapsd_max_sp_len; }; /** @@ -4205,31 +4214,33 @@ void ieee80211_rate_control_unregister(struct rate_control_ops *ops); static inline bool conf_is_ht20(struct ieee80211_conf *conf) { - return conf->channel_type == NL80211_CHAN_HT20; + return conf->chandef.width == NL80211_CHAN_WIDTH_20; } static inline bool conf_is_ht40_minus(struct ieee80211_conf *conf) { - return conf->channel_type == NL80211_CHAN_HT40MINUS; + return conf->chandef.width == NL80211_CHAN_WIDTH_40 && + conf->chandef.center_freq1 < conf->chandef.chan->center_freq; } static inline bool conf_is_ht40_plus(struct ieee80211_conf *conf) { - return conf->channel_type == NL80211_CHAN_HT40PLUS; + return conf->chandef.width == NL80211_CHAN_WIDTH_40 && + conf->chandef.center_freq1 > conf->chandef.chan->center_freq; } static inline bool conf_is_ht40(struct ieee80211_conf *conf) { - return conf_is_ht40_minus(conf) || conf_is_ht40_plus(conf); + return conf->chandef.width == NL80211_CHAN_WIDTH_40; } static inline bool conf_is_ht(struct ieee80211_conf *conf) { - return conf->channel_type != NL80211_CHAN_NO_HT; + return conf->chandef.width != NL80211_CHAN_WIDTH_20_NOHT; } static inline enum nl80211_iftype diff --git a/include/net/nfc/nfc.h b/include/net/nfc/nfc.h index 87a6417fc93..5eb80bb3cbb 100644 --- a/include/net/nfc/nfc.h +++ b/include/net/nfc/nfc.h @@ -122,6 +122,8 @@ struct nfc_dev { bool shutting_down; + struct rfkill *rfkill; + struct nfc_ops *ops; }; #define to_nfc_dev(_dev) container_of(_dev, struct nfc_dev, dev) diff --git a/include/uapi/linux/nfc.h b/include/uapi/linux/nfc.h index 7440bc81a04..7c6f627a717 100644 --- a/include/uapi/linux/nfc.h +++ b/include/uapi/linux/nfc.h @@ -233,7 +233,10 @@ struct sockaddr_nfc_llcp { #define NFC_LLCP_DIRECTION_TX 0x01 /* socket option names */ -#define NFC_LLCP_RW 0 -#define NFC_LLCP_MIUX 1 +#define NFC_LLCP_RW 0 +#define NFC_LLCP_MIUX 1 +#define NFC_LLCP_REMOTE_MIU 2 +#define NFC_LLCP_REMOTE_LTO 3 +#define NFC_LLCP_REMOTE_RW 4 #endif /*__LINUX_NFC_H */ diff --git a/include/uapi/linux/rfkill.h b/include/uapi/linux/rfkill.h index 2753c6cc974..058757f7a73 100644 --- a/include/uapi/linux/rfkill.h +++ b/include/uapi/linux/rfkill.h @@ -37,6 +37,7 @@ * @RFKILL_TYPE_WWAN: switch is on a wireless WAN device. * @RFKILL_TYPE_GPS: switch is on a GPS device. * @RFKILL_TYPE_FM: switch is on a FM radio device. + * @RFKILL_TYPE_NFC: switch is on an NFC device. * @NUM_RFKILL_TYPES: number of defined rfkill types */ enum rfkill_type { @@ -48,6 +49,7 @@ enum rfkill_type { RFKILL_TYPE_WWAN, RFKILL_TYPE_GPS, RFKILL_TYPE_FM, + RFKILL_TYPE_NFC, NUM_RFKILL_TYPES, }; |