diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/asm-generic/gpio.h | 47 | ||||
| -rw-r--r-- | include/linux/gpio.h | 21 | ||||
| -rw-r--r-- | include/linux/pinctrl/pinconf-generic.h | 5 | ||||
| -rw-r--r-- | include/linux/pinctrl/pinctrl.h | 19 | ||||
| -rw-r--r-- | include/linux/platform_data/pinctrl-coh901.h | 4 | ||||
| -rw-r--r-- | include/linux/platform_data/pinctrl-nomadik.h | 266 |
6 files changed, 353 insertions, 9 deletions
diff --git a/include/asm-generic/gpio.h b/include/asm-generic/gpio.h index a9432fc6b8b..9fd3093d855 100644 --- a/include/asm-generic/gpio.h +++ b/include/asm-generic/gpio.h @@ -5,6 +5,7 @@ #include <linux/types.h> #include <linux/errno.h> #include <linux/of.h> +#include <linux/pinctrl/pinctrl.h> #ifdef CONFIG_GPIOLIB @@ -134,6 +135,15 @@ struct gpio_chip { int (*of_xlate)(struct gpio_chip *gc, const struct of_phandle_args *gpiospec, u32 *flags); #endif +#ifdef CONFIG_PINCTRL + /* + * If CONFIG_PINCTRL is enabled, then gpio controllers can optionally + * describe the actual pin range which they serve in an SoC. This + * information would be used by pinctrl subsystem to configure + * corresponding pins for gpio usage. + */ + struct list_head pin_ranges; +#endif }; extern const char *gpiochip_is_requested(struct gpio_chip *chip, @@ -257,4 +267,41 @@ static inline void gpio_unexport(unsigned gpio) } #endif /* CONFIG_GPIO_SYSFS */ +#ifdef CONFIG_PINCTRL + +/** + * struct gpio_pin_range - pin range controlled by a gpio chip + * @head: list for maintaining set of pin ranges, used internally + * @pctldev: pinctrl device which handles corresponding pins + * @range: actual range of pins controlled by a gpio controller + */ + +struct gpio_pin_range { + struct list_head node; + struct pinctrl_dev *pctldev; + struct pinctrl_gpio_range range; +}; + +int gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name, + unsigned int gpio_offset, unsigned int pin_offset, + unsigned int npins); +void gpiochip_remove_pin_ranges(struct gpio_chip *chip); + +#else + +static inline int +gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name, + unsigned int gpio_offset, unsigned int pin_offset, + unsigned int npins) +{ + return 0; +} + +static inline void +gpiochip_remove_pin_ranges(struct gpio_chip *chip) +{ +} + +#endif /* CONFIG_PINCTRL */ + #endif /* _ASM_GENERIC_GPIO_H */ diff --git a/include/linux/gpio.h b/include/linux/gpio.h index 2e31e8b3a19..bfe66562153 100644 --- a/include/linux/gpio.h +++ b/include/linux/gpio.h @@ -72,9 +72,9 @@ static inline int irq_to_gpio(unsigned int irq) return -EINVAL; } -#endif +#endif /* ! CONFIG_ARCH_HAVE_CUSTOM_GPIO_H */ -#else +#else /* ! CONFIG_GENERIC_GPIO */ #include <linux/kernel.h> #include <linux/types.h> @@ -231,6 +231,21 @@ static inline int irq_to_gpio(unsigned irq) return -EINVAL; } -#endif +static inline int +gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name, + unsigned int gpio_offset, unsigned int pin_offset, + unsigned int npins) +{ + WARN_ON(1); + return -EINVAL; +} + +static inline void +gpiochip_remove_pin_ranges(struct gpio_chip *chip) +{ + WARN_ON(1); +} + +#endif /* ! CONFIG_GENERIC_GPIO */ #endif /* __LINUX_GPIO_H */ diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h index 4f0abb9f1c0..47a1bdd8887 100644 --- a/include/linux/pinctrl/pinconf-generic.h +++ b/include/linux/pinctrl/pinconf-generic.h @@ -46,11 +46,11 @@ * @PIN_CONFIG_DRIVE_OPEN_SOURCE: the pin will be driven with open source * (open emitter). Sending this config will enabale open drain mode, the * argument is ignored. + * @PIN_CONFIG_INPUT_SCHMITT_DISABLE: disable schmitt-trigger mode on the pin. * @PIN_CONFIG_INPUT_SCHMITT: this will configure an input pin to run in * schmitt-trigger mode. If the schmitt-trigger has adjustable hysteresis, * the threshold value is given on a custom format as argument when - * setting pins to this mode. The argument zero turns the schmitt trigger - * off. + * setting pins to this mode. * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode, * which means it will wait for signals to settle when reading inputs. The * argument gives the debounce time on a custom format. Setting the @@ -74,6 +74,7 @@ enum pin_config_param { PIN_CONFIG_DRIVE_PUSH_PULL, PIN_CONFIG_DRIVE_OPEN_DRAIN, PIN_CONFIG_DRIVE_OPEN_SOURCE, + PIN_CONFIG_INPUT_SCHMITT_DISABLE, PIN_CONFIG_INPUT_SCHMITT, PIN_CONFIG_INPUT_DEBOUNCE, PIN_CONFIG_POWER_SOURCE, diff --git a/include/linux/pinctrl/pinctrl.h b/include/linux/pinctrl/pinctrl.h index 7d087f03e91..04d6700d99a 100644 --- a/include/linux/pinctrl/pinctrl.h +++ b/include/linux/pinctrl/pinctrl.h @@ -134,6 +134,25 @@ extern void pinctrl_add_gpio_range(struct pinctrl_dev *pctldev, extern void pinctrl_add_gpio_ranges(struct pinctrl_dev *pctldev, struct pinctrl_gpio_range *ranges, unsigned nranges); +extern void pinctrl_remove_gpio_range(struct pinctrl_dev *pctldev, + struct pinctrl_gpio_range *range); + +extern struct pinctrl_dev *pinctrl_find_and_add_gpio_range(const char *devname, + struct pinctrl_gpio_range *range); +extern struct pinctrl_gpio_range * +pinctrl_find_gpio_range_from_pin(struct pinctrl_dev *pctldev, + unsigned int pin); + +#ifdef CONFIG_OF +extern struct pinctrl_dev *of_pinctrl_get(struct device_node *np); +#else +static inline +struct pinctrl_dev *of_pinctrl_get(struct device_node *np) +{ + return NULL; +} +#endif /* CONFIG_OF */ + extern const char *pinctrl_dev_get_name(struct pinctrl_dev *pctldev); extern void *pinctrl_dev_get_drvdata(struct pinctrl_dev *pctldev); #else diff --git a/include/linux/platform_data/pinctrl-coh901.h b/include/linux/platform_data/pinctrl-coh901.h index 30dea251b83..dfbc65d1048 100644 --- a/include/linux/platform_data/pinctrl-coh901.h +++ b/include/linux/platform_data/pinctrl-coh901.h @@ -13,14 +13,10 @@ * struct u300_gpio_platform - U300 GPIO platform data * @ports: number of GPIO block ports * @gpio_base: first GPIO number for this block (use a free range) - * @gpio_irq_base: first GPIO IRQ number for this block (use a free range) - * @pinctrl_device: pin control device to spawn as child */ struct u300_gpio_platform { u8 ports; int gpio_base; - int gpio_irq_base; - struct platform_device *pinctrl_device; }; #endif /* __MACH_U300_GPIO_U300_H */ diff --git a/include/linux/platform_data/pinctrl-nomadik.h b/include/linux/platform_data/pinctrl-nomadik.h new file mode 100644 index 00000000000..f73b2f0c55b --- /dev/null +++ b/include/linux/platform_data/pinctrl-nomadik.h @@ -0,0 +1,266 @@ +/* + * Structures and registers for GPIO access in the Nomadik SoC + * + * Copyright (C) 2008 STMicroelectronics + * Author: Prafulla WADASKAR <prafulla.wadaskar@st.com> + * Copyright (C) 2009 Alessandro Rubini <rubini@unipv.it> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __PLAT_NOMADIK_GPIO +#define __PLAT_NOMADIK_GPIO + +/* + * pin configurations are represented by 32-bit integers: + * + * bit 0.. 8 - Pin Number (512 Pins Maximum) + * bit 9..10 - Alternate Function Selection + * bit 11..12 - Pull up/down state + * bit 13 - Sleep mode behaviour + * bit 14 - Direction + * bit 15 - Value (if output) + * bit 16..18 - SLPM pull up/down state + * bit 19..20 - SLPM direction + * bit 21..22 - SLPM Value (if output) + * bit 23..25 - PDIS value (if input) + * bit 26 - Gpio mode + * bit 27 - Sleep mode + * + * to facilitate the definition, the following macros are provided + * + * PIN_CFG_DEFAULT - default config (0): + * pull up/down = disabled + * sleep mode = input/wakeup + * direction = input + * value = low + * SLPM direction = same as normal + * SLPM pull = same as normal + * SLPM value = same as normal + * + * PIN_CFG - default config with alternate function + */ + +typedef unsigned long pin_cfg_t; + +#define PIN_NUM_MASK 0x1ff +#define PIN_NUM(x) ((x) & PIN_NUM_MASK) + +#define PIN_ALT_SHIFT 9 +#define PIN_ALT_MASK (0x3 << PIN_ALT_SHIFT) +#define PIN_ALT(x) (((x) & PIN_ALT_MASK) >> PIN_ALT_SHIFT) +#define PIN_GPIO (NMK_GPIO_ALT_GPIO << PIN_ALT_SHIFT) +#define PIN_ALT_A (NMK_GPIO_ALT_A << PIN_ALT_SHIFT) +#define PIN_ALT_B (NMK_GPIO_ALT_B << PIN_ALT_SHIFT) +#define PIN_ALT_C (NMK_GPIO_ALT_C << PIN_ALT_SHIFT) + +#define PIN_PULL_SHIFT 11 +#define PIN_PULL_MASK (0x3 << PIN_PULL_SHIFT) +#define PIN_PULL(x) (((x) & PIN_PULL_MASK) >> PIN_PULL_SHIFT) +#define PIN_PULL_NONE (NMK_GPIO_PULL_NONE << PIN_PULL_SHIFT) +#define PIN_PULL_UP (NMK_GPIO_PULL_UP << PIN_PULL_SHIFT) +#define PIN_PULL_DOWN (NMK_GPIO_PULL_DOWN << PIN_PULL_SHIFT) + +#define PIN_SLPM_SHIFT 13 +#define PIN_SLPM_MASK (0x1 << PIN_SLPM_SHIFT) +#define PIN_SLPM(x) (((x) & PIN_SLPM_MASK) >> PIN_SLPM_SHIFT) +#define PIN_SLPM_MAKE_INPUT (NMK_GPIO_SLPM_INPUT << PIN_SLPM_SHIFT) +#define PIN_SLPM_NOCHANGE (NMK_GPIO_SLPM_NOCHANGE << PIN_SLPM_SHIFT) +/* These two replace the above in DB8500v2+ */ +#define PIN_SLPM_WAKEUP_ENABLE (NMK_GPIO_SLPM_WAKEUP_ENABLE << PIN_SLPM_SHIFT) +#define PIN_SLPM_WAKEUP_DISABLE (NMK_GPIO_SLPM_WAKEUP_DISABLE << PIN_SLPM_SHIFT) +#define PIN_SLPM_USE_MUX_SETTINGS_IN_SLEEP PIN_SLPM_WAKEUP_DISABLE + +#define PIN_SLPM_GPIO PIN_SLPM_WAKEUP_ENABLE /* In SLPM, pin is a gpio */ +#define PIN_SLPM_ALTFUNC PIN_SLPM_WAKEUP_DISABLE /* In SLPM, pin is altfunc */ + +#define PIN_DIR_SHIFT 14 +#define PIN_DIR_MASK (0x1 << PIN_DIR_SHIFT) +#define PIN_DIR(x) (((x) & PIN_DIR_MASK) >> PIN_DIR_SHIFT) +#define PIN_DIR_INPUT (0 << PIN_DIR_SHIFT) +#define PIN_DIR_OUTPUT (1 << PIN_DIR_SHIFT) + +#define PIN_VAL_SHIFT 15 +#define PIN_VAL_MASK (0x1 << PIN_VAL_SHIFT) +#define PIN_VAL(x) (((x) & PIN_VAL_MASK) >> PIN_VAL_SHIFT) +#define PIN_VAL_LOW (0 << PIN_VAL_SHIFT) +#define PIN_VAL_HIGH (1 << PIN_VAL_SHIFT) + +#define PIN_SLPM_PULL_SHIFT 16 +#define PIN_SLPM_PULL_MASK (0x7 << PIN_SLPM_PULL_SHIFT) +#define PIN_SLPM_PULL(x) \ + (((x) & PIN_SLPM_PULL_MASK) >> PIN_SLPM_PULL_SHIFT) +#define PIN_SLPM_PULL_NONE \ + ((1 + NMK_GPIO_PULL_NONE) << PIN_SLPM_PULL_SHIFT) +#define PIN_SLPM_PULL_UP \ + ((1 + NMK_GPIO_PULL_UP) << PIN_SLPM_PULL_SHIFT) +#define PIN_SLPM_PULL_DOWN \ + ((1 + NMK_GPIO_PULL_DOWN) << PIN_SLPM_PULL_SHIFT) + +#define PIN_SLPM_DIR_SHIFT 19 +#define PIN_SLPM_DIR_MASK (0x3 << PIN_SLPM_DIR_SHIFT) +#define PIN_SLPM_DIR(x) \ + (((x) & PIN_SLPM_DIR_MASK) >> PIN_SLPM_DIR_SHIFT) +#define PIN_SLPM_DIR_INPUT ((1 + 0) << PIN_SLPM_DIR_SHIFT) +#define PIN_SLPM_DIR_OUTPUT ((1 + 1) << PIN_SLPM_DIR_SHIFT) + +#define PIN_SLPM_VAL_SHIFT 21 +#define PIN_SLPM_VAL_MASK (0x3 << PIN_SLPM_VAL_SHIFT) +#define PIN_SLPM_VAL(x) \ + (((x) & PIN_SLPM_VAL_MASK) >> PIN_SLPM_VAL_SHIFT) +#define PIN_SLPM_VAL_LOW ((1 + 0) << PIN_SLPM_VAL_SHIFT) +#define PIN_SLPM_VAL_HIGH ((1 + 1) << PIN_SLPM_VAL_SHIFT) + +#define PIN_SLPM_PDIS_SHIFT 23 +#define PIN_SLPM_PDIS_MASK (0x3 << PIN_SLPM_PDIS_SHIFT) +#define PIN_SLPM_PDIS(x) \ + (((x) & PIN_SLPM_PDIS_MASK) >> PIN_SLPM_PDIS_SHIFT) +#define PIN_SLPM_PDIS_NO_CHANGE (0 << PIN_SLPM_PDIS_SHIFT) +#define PIN_SLPM_PDIS_DISABLED (1 << PIN_SLPM_PDIS_SHIFT) +#define PIN_SLPM_PDIS_ENABLED (2 << PIN_SLPM_PDIS_SHIFT) + +#define PIN_LOWEMI_SHIFT 25 +#define PIN_LOWEMI_MASK (0x1 << PIN_LOWEMI_SHIFT) +#define PIN_LOWEMI(x) (((x) & PIN_LOWEMI_MASK) >> PIN_LOWEMI_SHIFT) +#define PIN_LOWEMI_DISABLED (0 << PIN_LOWEMI_SHIFT) +#define PIN_LOWEMI_ENABLED (1 << PIN_LOWEMI_SHIFT) + +#define PIN_GPIOMODE_SHIFT 26 +#define PIN_GPIOMODE_MASK (0x1 << PIN_GPIOMODE_SHIFT) +#define PIN_GPIOMODE(x) (((x) & PIN_GPIOMODE_MASK) >> PIN_GPIOMODE_SHIFT) +#define PIN_GPIOMODE_DISABLED (0 << PIN_GPIOMODE_SHIFT) +#define PIN_GPIOMODE_ENABLED (1 << PIN_GPIOMODE_SHIFT) + +#define PIN_SLEEPMODE_SHIFT 27 +#define PIN_SLEEPMODE_MASK (0x1 << PIN_SLEEPMODE_SHIFT) +#define PIN_SLEEPMODE(x) (((x) & PIN_SLEEPMODE_MASK) >> PIN_SLEEPMODE_SHIFT) +#define PIN_SLEEPMODE_DISABLED (0 << PIN_SLEEPMODE_SHIFT) +#define PIN_SLEEPMODE_ENABLED (1 << PIN_SLEEPMODE_SHIFT) + + +/* Shortcuts. Use these instead of separate DIR, PULL, and VAL. */ +#define PIN_INPUT_PULLDOWN (PIN_DIR_INPUT | PIN_PULL_DOWN) +#define PIN_INPUT_PULLUP (PIN_DIR_INPUT | PIN_PULL_UP) +#define PIN_INPUT_NOPULL (PIN_DIR_INPUT | PIN_PULL_NONE) +#define PIN_OUTPUT_LOW (PIN_DIR_OUTPUT | PIN_VAL_LOW) +#define PIN_OUTPUT_HIGH (PIN_DIR_OUTPUT | PIN_VAL_HIGH) + +#define PIN_SLPM_INPUT_PULLDOWN (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_DOWN) +#define PIN_SLPM_INPUT_PULLUP (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_UP) +#define PIN_SLPM_INPUT_NOPULL (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_NONE) +#define PIN_SLPM_OUTPUT_LOW (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_LOW) +#define PIN_SLPM_OUTPUT_HIGH (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_HIGH) + +#define PIN_CFG_DEFAULT (0) + +#define PIN_CFG(num, alt) \ + (PIN_CFG_DEFAULT |\ + (PIN_NUM(num) | PIN_##alt)) + +#define PIN_CFG_INPUT(num, alt, pull) \ + (PIN_CFG_DEFAULT |\ + (PIN_NUM(num) | PIN_##alt | PIN_INPUT_##pull)) + +#define PIN_CFG_OUTPUT(num, alt, val) \ + (PIN_CFG_DEFAULT |\ + (PIN_NUM(num) | PIN_##alt | PIN_OUTPUT_##val)) + +/* + * "nmk_gpio" and "NMK_GPIO" stand for "Nomadik GPIO", leaving + * the "gpio" namespace for generic and cross-machine functions + */ + +#define GPIO_BLOCK_SHIFT 5 +#define NMK_GPIO_PER_CHIP (1 << GPIO_BLOCK_SHIFT) + +/* Register in the logic block */ +#define NMK_GPIO_DAT 0x00 +#define NMK_GPIO_DATS 0x04 +#define NMK_GPIO_DATC 0x08 +#define NMK_GPIO_PDIS 0x0c +#define NMK_GPIO_DIR 0x10 +#define NMK_GPIO_DIRS 0x14 +#define NMK_GPIO_DIRC 0x18 +#define NMK_GPIO_SLPC 0x1c +#define NMK_GPIO_AFSLA 0x20 +#define NMK_GPIO_AFSLB 0x24 +#define NMK_GPIO_LOWEMI 0x28 + +#define NMK_GPIO_RIMSC 0x40 +#define NMK_GPIO_FIMSC 0x44 +#define NMK_GPIO_IS 0x48 +#define NMK_GPIO_IC 0x4c +#define NMK_GPIO_RWIMSC 0x50 +#define NMK_GPIO_FWIMSC 0x54 +#define NMK_GPIO_WKS 0x58 +/* These appear in DB8540 and later ASICs */ +#define NMK_GPIO_EDGELEVEL 0x5C +#define NMK_GPIO_LEVEL 0x60 + +/* Alternate functions: function C is set in hw by setting both A and B */ +#define NMK_GPIO_ALT_GPIO 0 +#define NMK_GPIO_ALT_A 1 +#define NMK_GPIO_ALT_B 2 +#define NMK_GPIO_ALT_C (NMK_GPIO_ALT_A | NMK_GPIO_ALT_B) + +#define NMK_GPIO_ALT_CX_SHIFT 2 +#define NMK_GPIO_ALT_C1 ((1<<NMK_GPIO_ALT_CX_SHIFT) | NMK_GPIO_ALT_C) +#define NMK_GPIO_ALT_C2 ((2<<NMK_GPIO_ALT_CX_SHIFT) | NMK_GPIO_ALT_C) +#define NMK_GPIO_ALT_C3 ((3<<NMK_GPIO_ALT_CX_SHIFT) | NMK_GPIO_ALT_C) +#define NMK_GPIO_ALT_C4 ((4<<NMK_GPIO_ALT_CX_SHIFT) | NMK_GPIO_ALT_C) + +/* Pull up/down values */ +enum nmk_gpio_pull { + NMK_GPIO_PULL_NONE, + NMK_GPIO_PULL_UP, + NMK_GPIO_PULL_DOWN, +}; + +/* Sleep mode */ +enum nmk_gpio_slpm { + NMK_GPIO_SLPM_INPUT, + NMK_GPIO_SLPM_WAKEUP_ENABLE = NMK_GPIO_SLPM_INPUT, + NMK_GPIO_SLPM_NOCHANGE, + NMK_GPIO_SLPM_WAKEUP_DISABLE = NMK_GPIO_SLPM_NOCHANGE, +}; + +/* Older deprecated pin config API that should go away soon */ +extern int nmk_config_pin(pin_cfg_t cfg, bool sleep); +extern int nmk_config_pins(pin_cfg_t *cfgs, int num); +extern int nmk_config_pins_sleep(pin_cfg_t *cfgs, int num); +extern int nmk_gpio_set_slpm(int gpio, enum nmk_gpio_slpm mode); +extern int nmk_gpio_set_pull(int gpio, enum nmk_gpio_pull pull); +#ifdef CONFIG_PINCTRL_NOMADIK +extern int nmk_gpio_set_mode(int gpio, int gpio_mode); +#else +static inline int nmk_gpio_set_mode(int gpio, int gpio_mode) +{ + return -ENODEV; +} +#endif +extern int nmk_gpio_get_mode(int gpio); + +extern void nmk_gpio_wakeups_suspend(void); +extern void nmk_gpio_wakeups_resume(void); + +extern void nmk_gpio_clocks_enable(void); +extern void nmk_gpio_clocks_disable(void); + +extern void nmk_gpio_read_pull(int gpio_bank, u32 *pull_up); + +/* + * Platform data to register a block: only the initial gpio/irq number. + */ +struct nmk_gpio_platform_data { + char *name; + int first_gpio; + int first_irq; + int num_gpio; + u32 (*get_secondary_status)(unsigned int bank); + void (*set_ioforce)(bool enable); + bool supports_sleepmode; +}; + +#endif /* __PLAT_NOMADIK_GPIO */ |