diff options
Diffstat (limited to 'kernel/time/timekeeping.c')
| -rw-r--r-- | kernel/time/timekeeping.c | 96 |
1 files changed, 94 insertions, 2 deletions
diff --git a/kernel/time/timekeeping.c b/kernel/time/timekeeping.c index 2b021b0e850..e6a5a6bc276 100644 --- a/kernel/time/timekeeping.c +++ b/kernel/time/timekeeping.c @@ -131,7 +131,7 @@ static inline s64 timekeeping_get_ns_raw(void) /* calculate the delta since the last update_wall_time: */ cycle_delta = (cycle_now - clock->cycle_last) & clock->mask; - /* return delta convert to nanoseconds using ntp adjusted mult. */ + /* return delta convert to nanoseconds. */ return clocksource_cyc2ns(cycle_delta, clock->mult, clock->shift); } @@ -249,6 +249,8 @@ ktime_t ktime_get(void) secs = xtime.tv_sec + wall_to_monotonic.tv_sec; nsecs = xtime.tv_nsec + wall_to_monotonic.tv_nsec; nsecs += timekeeping_get_ns(); + /* If arch requires, add in gettimeoffset() */ + nsecs += arch_gettimeoffset(); } while (read_seqretry(&xtime_lock, seq)); /* @@ -280,6 +282,8 @@ void ktime_get_ts(struct timespec *ts) *ts = xtime; tomono = wall_to_monotonic; nsecs = timekeeping_get_ns(); + /* If arch requires, add in gettimeoffset() */ + nsecs += arch_gettimeoffset(); } while (read_seqretry(&xtime_lock, seq)); @@ -802,14 +806,44 @@ static void timekeeping_adjust(s64 offset) s64 error, interval = timekeeper.cycle_interval; int adj; + /* + * The point of this is to check if the error is greater then half + * an interval. + * + * First we shift it down from NTP_SHIFT to clocksource->shifted nsecs. + * + * Note we subtract one in the shift, so that error is really error*2. + * This "saves" dividing(shifting) interval twice, but keeps the + * (error > interval) comparison as still measuring if error is + * larger then half an interval. + * + * Note: It does not "save" on aggravation when reading the code. + */ error = timekeeper.ntp_error >> (timekeeper.ntp_error_shift - 1); if (error > interval) { + /* + * We now divide error by 4(via shift), which checks if + * the error is greater then twice the interval. + * If it is greater, we need a bigadjust, if its smaller, + * we can adjust by 1. + */ error >>= 2; + /* + * XXX - In update_wall_time, we round up to the next + * nanosecond, and store the amount rounded up into + * the error. This causes the likely below to be unlikely. + * + * The proper fix is to avoid rounding up by using + * the high precision timekeeper.xtime_nsec instead of + * xtime.tv_nsec everywhere. Fixing this will take some + * time. + */ if (likely(error <= interval)) adj = 1; else adj = timekeeping_bigadjust(error, &interval, &offset); } else if (error < -interval) { + /* See comment above, this is just switched for the negative */ error >>= 2; if (likely(error >= -interval)) { adj = -1; @@ -817,9 +851,65 @@ static void timekeeping_adjust(s64 offset) offset = -offset; } else adj = timekeeping_bigadjust(error, &interval, &offset); - } else + } else /* No adjustment needed */ return; + WARN_ONCE(timekeeper.clock->maxadj && + (timekeeper.mult + adj > timekeeper.clock->mult + + timekeeper.clock->maxadj), + "Adjusting %s more then 11%% (%ld vs %ld)\n", + timekeeper.clock->name, (long)timekeeper.mult + adj, + (long)timekeeper.clock->mult + + timekeeper.clock->maxadj); + /* + * So the following can be confusing. + * + * To keep things simple, lets assume adj == 1 for now. + * + * When adj != 1, remember that the interval and offset values + * have been appropriately scaled so the math is the same. + * + * The basic idea here is that we're increasing the multiplier + * by one, this causes the xtime_interval to be incremented by + * one cycle_interval. This is because: + * xtime_interval = cycle_interval * mult + * So if mult is being incremented by one: + * xtime_interval = cycle_interval * (mult + 1) + * Its the same as: + * xtime_interval = (cycle_interval * mult) + cycle_interval + * Which can be shortened to: + * xtime_interval += cycle_interval + * + * So offset stores the non-accumulated cycles. Thus the current + * time (in shifted nanoseconds) is: + * now = (offset * adj) + xtime_nsec + * Now, even though we're adjusting the clock frequency, we have + * to keep time consistent. In other words, we can't jump back + * in time, and we also want to avoid jumping forward in time. + * + * So given the same offset value, we need the time to be the same + * both before and after the freq adjustment. + * now = (offset * adj_1) + xtime_nsec_1 + * now = (offset * adj_2) + xtime_nsec_2 + * So: + * (offset * adj_1) + xtime_nsec_1 = + * (offset * adj_2) + xtime_nsec_2 + * And we know: + * adj_2 = adj_1 + 1 + * So: + * (offset * adj_1) + xtime_nsec_1 = + * (offset * (adj_1+1)) + xtime_nsec_2 + * (offset * adj_1) + xtime_nsec_1 = + * (offset * adj_1) + offset + xtime_nsec_2 + * Canceling the sides: + * xtime_nsec_1 = offset + xtime_nsec_2 + * Which gives us: + * xtime_nsec_2 = xtime_nsec_1 - offset + * Which simplfies to: + * xtime_nsec -= offset + * + * XXX - TODO: Doc ntp_error calculation. + */ timekeeper.mult += adj; timekeeper.xtime_interval += interval; timekeeper.xtime_nsec -= offset; @@ -1140,6 +1230,8 @@ ktime_t ktime_get_monotonic_offset(void) } while (read_seqretry(&xtime_lock, seq)); return timespec_to_ktime(wtom); } +EXPORT_SYMBOL_GPL(ktime_get_monotonic_offset); + /** * xtime_update() - advances the timekeeping infrastructure |