diff options
Diffstat (limited to 'sound/oss/nm256.h')
| -rw-r--r-- | sound/oss/nm256.h | 295 |
1 files changed, 295 insertions, 0 deletions
diff --git a/sound/oss/nm256.h b/sound/oss/nm256.h new file mode 100644 index 00000000000..eae7d99d682 --- /dev/null +++ b/sound/oss/nm256.h @@ -0,0 +1,295 @@ +#ifndef _NM256_H_ +#define _NM256_H_ + +#include <linux/spinlock.h> +#include <linux/interrupt.h> + +#include "ac97.h" + +/* The revisions that we currently handle. */ +enum nm256rev { + REV_NM256AV, REV_NM256ZX +}; + +/* Per-card structure. */ +struct nm256_info +{ + /* Magic number used to verify that this struct is valid. */ +#define NM_MAGIC_SIG 0x55aa00ff + int magsig; + + /* Revision number */ + enum nm256rev rev; + + struct ac97_hwint mdev; + + /* Our audio device numbers. */ + int dev[2]; + + /* The # of times each device has been opened. (Should only be + 0 or 1). */ + int opencnt[2]; + + /* We use two devices, because we can do simultaneous play and record. + This keeps track of which device is being used for what purpose; + these are the actual device numbers. */ + int dev_for_play; + int dev_for_record; + + spinlock_t lock; + + /* The mixer device. */ + int mixer_oss_dev; + + /* + * Can only be opened once for each operation. These aren't set + * until an actual I/O operation is performed; this allows one + * device to be open for read/write without inhibiting I/O to + * the other device. + */ + int is_open_play; + int is_open_record; + + /* Non-zero if we're currently playing a sample. */ + int playing; + /* Ditto for recording a sample. */ + int recording; + + /* The two memory ports. */ + struct nm256_ports { + /* Physical address of the port. */ + u32 physaddr; + /* Our mapped-in pointer. */ + char __iomem *ptr; + /* PTR's offset within the physical port. */ + u32 start_offset; + /* And the offset of the end of the buffer. */ + u32 end_offset; + } port[2]; + + /* The following are offsets within memory port 1. */ + u32 coeffBuf; + u32 allCoeffBuf; + + /* Record and playback buffers. */ + u32 abuf1, abuf2; + + /* Offset of the AC97 mixer in memory port 2. */ + u32 mixer; + + /* Offset of the mixer status register in memory port 2. */ + u32 mixer_status_offset; + + /* Non-zero if we have written initial values to the mixer. */ + u8 mixer_values_init; + + /* + * Status mask bit; (*mixer_status_loc & mixer_status_mask) == 0 means + * it's ready. + */ + u16 mixer_status_mask; + + /* The sizes of the playback and record ring buffers. */ + u32 playbackBufferSize; + u32 recordBufferSize; + + /* Are the coefficient values in the memory cache current? */ + u8 coeffsCurrent; + + /* For writes, the amount we last wrote. */ + u32 requested_amt; + /* The start of the block currently playing. */ + u32 curPlayPos; + + /* The amount of data we were requested to record. */ + u32 requestedRecAmt; + /* The offset of the currently-recording block. */ + u32 curRecPos; + /* The destination buffer. */ + char *recBuf; + + /* Our IRQ number. */ + int irq; + + /* A flag indicating how many times we've grabbed the IRQ. */ + int has_irq; + + /* The card interrupt service routine. */ + irqreturn_t (*introutine) (int, void *, struct pt_regs *); + + /* Current audio config, cached. */ + struct sinfo { + u32 samplerate; + u8 bits; + u8 stereo; + } sinfo[2]; /* goes with each device */ + + /* The cards are stored in a chain; this is the next card. */ + struct nm256_info *next_card; +}; + +/* Debug flag--bigger numbers mean more output. */ +extern int nm256_debug; + +/* The BIOS signature. */ +#define NM_SIGNATURE 0x4e4d0000 +/* Signature mask. */ +#define NM_SIG_MASK 0xffff0000 + +/* Size of the second memory area. */ +#define NM_PORT2_SIZE 4096 + +/* The base offset of the mixer in the second memory area. */ +#define NM_MIXER_OFFSET 0x600 + +/* The maximum size of a coefficient entry. */ +#define NM_MAX_COEFFICIENT 0x5000 + +/* The interrupt register. */ +#define NM_INT_REG 0xa04 +/* And its bits. */ +#define NM_PLAYBACK_INT 0x40 +#define NM_RECORD_INT 0x100 +#define NM_MISC_INT_1 0x4000 +#define NM_MISC_INT_2 0x1 +#define NM_ACK_INT(CARD, X) nm256_writePort16((CARD), 2, NM_INT_REG, (X) << 1) + +/* The AV's "mixer ready" status bit and location. */ +#define NM_MIXER_STATUS_OFFSET 0xa04 +#define NM_MIXER_READY_MASK 0x0800 +#define NM_MIXER_PRESENCE 0xa06 +#define NM_PRESENCE_MASK 0x0050 +#define NM_PRESENCE_VALUE 0x0040 + +/* + * For the ZX. It uses the same interrupt register, but it holds 32 + * bits instead of 16. + */ +#define NM2_PLAYBACK_INT 0x10000 +#define NM2_RECORD_INT 0x80000 +#define NM2_MISC_INT_1 0x8 +#define NM2_MISC_INT_2 0x2 +#define NM2_ACK_INT(CARD, X) nm256_writePort32((CARD), 2, NM_INT_REG, (X)) + +/* The ZX's "mixer ready" status bit and location. */ +#define NM2_MIXER_STATUS_OFFSET 0xa06 +#define NM2_MIXER_READY_MASK 0x0800 + +/* The playback registers start from here. */ +#define NM_PLAYBACK_REG_OFFSET 0x0 +/* The record registers start from here. */ +#define NM_RECORD_REG_OFFSET 0x200 + +/* The rate register is located 2 bytes from the start of the register area. */ +#define NM_RATE_REG_OFFSET 2 + +/* Mono/stereo flag, number of bits on playback, and rate mask. */ +#define NM_RATE_STEREO 1 +#define NM_RATE_BITS_16 2 +#define NM_RATE_MASK 0xf0 + +/* Playback enable register. */ +#define NM_PLAYBACK_ENABLE_REG (NM_PLAYBACK_REG_OFFSET + 0x1) +#define NM_PLAYBACK_ENABLE_FLAG 1 +#define NM_PLAYBACK_ONESHOT 2 +#define NM_PLAYBACK_FREERUN 4 + +/* Mutes the audio output. */ +#define NM_AUDIO_MUTE_REG (NM_PLAYBACK_REG_OFFSET + 0x18) +#define NM_AUDIO_MUTE_LEFT 0x8000 +#define NM_AUDIO_MUTE_RIGHT 0x0080 + +/* Recording enable register. */ +#define NM_RECORD_ENABLE_REG (NM_RECORD_REG_OFFSET + 0) +#define NM_RECORD_ENABLE_FLAG 1 +#define NM_RECORD_FREERUN 2 + +#define NM_RBUFFER_START (NM_RECORD_REG_OFFSET + 0x4) +#define NM_RBUFFER_END (NM_RECORD_REG_OFFSET + 0x10) +#define NM_RBUFFER_WMARK (NM_RECORD_REG_OFFSET + 0xc) +#define NM_RBUFFER_CURRP (NM_RECORD_REG_OFFSET + 0x8) + +#define NM_PBUFFER_START (NM_PLAYBACK_REG_OFFSET + 0x4) +#define NM_PBUFFER_END (NM_PLAYBACK_REG_OFFSET + 0x14) +#define NM_PBUFFER_WMARK (NM_PLAYBACK_REG_OFFSET + 0xc) +#define NM_PBUFFER_CURRP (NM_PLAYBACK_REG_OFFSET + 0x8) + +/* A few trivial routines to make it easier to work with the registers + on the chip. */ + +/* This is a common code portion used to fix up the port offsets. */ +#define NM_FIX_PORT \ + if (port < 1 || port > 2 || card == NULL) \ + return -1; \ +\ + if (offset < card->port[port - 1].start_offset \ + || offset >= card->port[port - 1].end_offset) { \ + printk (KERN_ERR "Bad access: port %d, offset 0x%x\n", port, offset); \ + return -1; \ + } \ + offset -= card->port[port - 1].start_offset; + +#define DEFwritePortX(X, func) \ +static inline int nm256_writePort##X (struct nm256_info *card,\ + int port, int offset, int value)\ +{\ + u##X __iomem *addr;\ +\ + if (nm256_debug > 1)\ + printk (KERN_DEBUG "Writing 0x%x to %d:0x%x\n", value, port, offset);\ +\ + NM_FIX_PORT;\ +\ + addr = (u##X __iomem *)(card->port[port - 1].ptr + offset);\ + func (value, addr);\ + return 0;\ +} + +DEFwritePortX (8, writeb) +DEFwritePortX (16, writew) +DEFwritePortX (32, writel) + +#define DEFreadPortX(X, func) \ +static inline u##X nm256_readPort##X (struct nm256_info *card,\ + int port, int offset)\ +{\ + u##X __iomem *addr;\ +\ + NM_FIX_PORT\ +\ + addr = (u##X __iomem *)(card->port[port - 1].ptr + offset);\ + return func(addr);\ +} + +DEFreadPortX (8, readb) +DEFreadPortX (16, readw) +DEFreadPortX (32, readl) + +static inline int +nm256_writeBuffer8 (struct nm256_info *card, u8 *src, int port, int offset, + int amt) +{ + NM_FIX_PORT; + memcpy_toio (card->port[port - 1].ptr + offset, src, amt); + return 0; +} + +static inline int +nm256_readBuffer8 (struct nm256_info *card, u8 *dst, int port, int offset, + int amt) +{ + NM_FIX_PORT; + memcpy_fromio (dst, card->port[port - 1].ptr + offset, amt); + return 0; +} + +/* Returns a non-zero value if we should use the coefficient cache. */ +extern int nm256_cachedCoefficients (struct nm256_info *card); + +#endif + +/* + * Local variables: + * c-basic-offset: 4 + * End: + */ |