diff options
Diffstat (limited to 'sound/pci/maestro3.c')
-rw-r--r-- | sound/pci/maestro3.c | 22 |
1 files changed, 9 insertions, 13 deletions
diff --git a/sound/pci/maestro3.c b/sound/pci/maestro3.c index 2693b6f731f..ede7a75bfe0 100644 --- a/sound/pci/maestro3.c +++ b/sound/pci/maestro3.c @@ -1492,7 +1492,7 @@ static int snd_m3_pcm_hw_params(snd_pcm_substream_t * substream, /* set buffer address */ s->buffer_addr = substream->runtime->dma_addr; if (s->buffer_addr & 0x3) { - snd_printk("oh my, not aligned\n"); + snd_printk(KERN_ERR "oh my, not aligned\n"); s->buffer_addr = s->buffer_addr & ~0x3; } return 0; @@ -1942,7 +1942,7 @@ static int snd_m3_ac97_wait(m3_t *chip) return 0; } while (i-- > 0); - snd_printk("ac97 serial bus busy\n"); + snd_printk(KERN_ERR "ac97 serial bus busy\n"); return 1; } @@ -2046,8 +2046,7 @@ static void snd_m3_ac97_reset(m3_t *chip) outw(0, io + GPIO_DATA); outw(dir | GPO_PRIMARY_AC97, io + GPIO_DIRECTION); - set_current_state(TASK_UNINTERRUPTIBLE); - schedule_timeout((delay1 * HZ) / 1000); + schedule_timeout_uninterruptible(msecs_to_jiffies(delay1)); outw(GPO_PRIMARY_AC97, io + GPIO_DATA); udelay(5); @@ -2055,8 +2054,7 @@ static void snd_m3_ac97_reset(m3_t *chip) outw(IO_SRAM_ENABLE | SERIAL_AC_LINK_ENABLE, io + RING_BUS_CTRL_A); outw(~0, io + GPIO_MASK); - set_current_state(TASK_UNINTERRUPTIBLE); - schedule_timeout((delay2 * HZ) / 1000); + schedule_timeout_uninterruptible(msecs_to_jiffies(delay2)); if (! snd_m3_try_read_vendor(chip)) break; @@ -2101,8 +2099,7 @@ static int __devinit snd_m3_mixer(m3_t *chip) /* seems ac97 PCM needs initialization.. hack hack.. */ snd_ac97_write(chip->ac97, AC97_PCM, 0x8000 | (15 << 8) | 15); - set_current_state(TASK_UNINTERRUPTIBLE); - schedule_timeout(HZ / 10); + schedule_timeout_uninterruptible(msecs_to_jiffies(100)); snd_ac97_write(chip->ac97, AC97_PCM, 0); memset(&id, 0, sizeof(id)); @@ -2367,7 +2364,7 @@ static int __devinit snd_m3_assp_client_init(m3_t *chip, m3_dma_t *s, int index) address = 0x1100 + ((data_bytes/2) * index); if ((address + (data_bytes/2)) >= 0x1c00) { - snd_printk("no memory for %d bytes at ind %d (addr 0x%x)\n", + snd_printk(KERN_ERR "no memory for %d bytes at ind %d (addr 0x%x)\n", data_bytes, index, address); return -ENOMEM; } @@ -2476,6 +2473,7 @@ snd_m3_chip_init(m3_t *chip) t |= ASSP_0_WS_ENABLE; outb(t, chip->iobase + ASSP_CONTROL_A); + snd_m3_assp_init(chip); /* download DSP code before starting ASSP below */ outb(RUN_ASSP, chip->iobase + ASSP_CONTROL_B); outb(0x00, io + HARDWARE_VOL_CTRL); @@ -2655,7 +2653,7 @@ snd_m3_create(snd_card_t *card, struct pci_dev *pci, /* check, if we can restrict PCI DMA transfers to 28 bits */ if (pci_set_dma_mask(pci, 0x0fffffff) < 0 || pci_set_consistent_dma_mask(pci, 0x0fffffff) < 0) { - snd_printk("architecture does not support 28bit PCI busmaster DMA\n"); + snd_printk(KERN_ERR "architecture does not support 28bit PCI busmaster DMA\n"); pci_disable_device(pci); return -ENXIO; } @@ -2734,14 +2732,13 @@ snd_m3_create(snd_card_t *card, struct pci_dev *pci, snd_m3_ac97_reset(chip); - snd_m3_assp_init(chip); snd_m3_amp_enable(chip, 1); tasklet_init(&chip->hwvol_tq, snd_m3_update_hw_volume, (unsigned long)chip); if (request_irq(pci->irq, snd_m3_interrupt, SA_INTERRUPT|SA_SHIRQ, card->driver, (void *)chip)) { - snd_printk("unable to grab IRQ %d\n", pci->irq); + snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq); snd_m3_free(chip); return -ENOMEM; } @@ -2861,7 +2858,6 @@ static void __devexit snd_m3_remove(struct pci_dev *pci) static struct pci_driver driver = { .name = "Maestro3", - .owner = THIS_MODULE, .id_table = snd_m3_ids, .probe = snd_m3_probe, .remove = __devexit_p(snd_m3_remove), |