diff options
Diffstat (limited to 'tools/testing/ktest/sample.conf')
| -rw-r--r-- | tools/testing/ktest/sample.conf | 89 |
1 files changed, 87 insertions, 2 deletions
diff --git a/tools/testing/ktest/sample.conf b/tools/testing/ktest/sample.conf index dbedfa19672..5ea04c6a71b 100644 --- a/tools/testing/ktest/sample.conf +++ b/tools/testing/ktest/sample.conf @@ -346,7 +346,10 @@ #GRUB_MENU = Test Kernel # A script to reboot the target into the test kernel -# (Only mandatory if REBOOT_TYPE = script) +# This and SWITCH_TO_TEST are about the same, except +# SWITCH_TO_TEST is run even for REBOOT_TYPE = grub. +# This may be left undefined. +# (default undefined) #REBOOT_SCRIPT = #### Optional Config Options (all have defaults) #### @@ -468,6 +471,27 @@ # The test will not modify that file. #REBOOT_TYPE = grub +# If you are using a machine that doesn't boot with grub, and +# perhaps gets its kernel from a remote server (tftp), then +# you can use this option to update the target image with the +# test image. +# +# You could also do the same with POST_INSTALL, but the difference +# between that option and this option is that POST_INSTALL runs +# after the install, where this one runs just before a reboot. +# (default undefined) +#SWITCH_TO_TEST = cp ${OUTPUT_DIR}/${BUILD_TARGET} ${TARGET_IMAGE} + +# If you are using a machine that doesn't boot with grub, and +# perhaps gets its kernel from a remote server (tftp), then +# you can use this option to update the target image with the +# the known good image to reboot safely back into. +# +# This option holds a command that will execute before needing +# to reboot to a good known image. +# (default undefined) +#SWITCH_TO_GOOD = ssh ${SSH_USER}/${MACHINE} cp good_image ${TARGET_IMAGE} + # The min config that is needed to build for the machine # A nice way to create this is with the following: # @@ -589,6 +613,12 @@ # (default undefined) #STORE_FAILURES = /home/test/failures +# Directory to store success directories on success. If this is not +# set, the .config, dmesg and bootlog will not be saved if a +# test succeeds. +# (default undefined) +#STORE_SUCCESSES = /home/test/successes + # Build without doing a make mrproper, or removing .config # (default 0) #BUILD_NOCLEAN = 0 @@ -700,6 +730,25 @@ # (default 1) #DETECT_TRIPLE_FAULT = 0 +# All options in the config file should be either used by ktest +# or could be used within a value of another option. If an option +# in the config file is not used, ktest will warn about it and ask +# if you want to continue. +# +# If you don't care if there are non-used options, enable this +# option. Be careful though, a non-used option is usually a sign +# of an option name being typed incorrectly. +# (default 0) +#IGNORE_UNUSED = 1 + +# When testing a kernel that happens to have WARNINGs, and call +# traces, ktest.pl will detect these and fail a boot or test run +# due to warnings. By setting this option, ktest will ignore +# call traces, and will not fail a test if the kernel produces +# an oops. Use this option with care. +# (default 0) +#IGNORE_ERRORS = 1 + #### Per test run options #### # The following options are only allowed in TEST_START sections. # They are ignored in the DEFAULTS sections. @@ -862,6 +911,42 @@ # BISECT_BAD with BISECT_CHECK = good or # BISECT_CHECK = bad, respectively. # +# BISECT_RET_GOOD = 0 (optional, default undefined) +# +# In case the specificed test returns something other than just +# 0 for good, and non-zero for bad, you can override 0 being +# good by defining BISECT_RET_GOOD. +# +# BISECT_RET_BAD = 1 (optional, default undefined) +# +# In case the specificed test returns something other than just +# 0 for good, and non-zero for bad, you can override non-zero being +# bad by defining BISECT_RET_BAD. +# +# BISECT_RET_ABORT = 255 (optional, default undefined) +# +# If you need to abort the bisect if the test discovers something +# that was wrong, you can define BISECT_RET_ABORT to be the error +# code returned by the test in order to abort the bisect. +# +# BISECT_RET_SKIP = 2 (optional, default undefined) +# +# If the test detects that the current commit is neither good +# nor bad, but something else happened (another bug detected) +# you can specify BISECT_RET_SKIP to an error code that the +# test returns when it should skip the current commit. +# +# BISECT_RET_DEFAULT = good (optional, default undefined) +# +# You can override the default of what to do when the above +# options are not hit. This may be one of, "good", "bad", +# "abort" or "skip" (without the quotes). +# +# Note, if you do not define any of the previous BISECT_RET_* +# and define BISECT_RET_DEFAULT, all bisects results will do +# what the BISECT_RET_DEFAULT has. +# +# # Example: # TEST_START # TEST_TYPE = bisect @@ -950,7 +1035,7 @@ # TEST_START # TEST_TYPE = config_bisect # CONFIG_BISECT_TYPE = build -# CONFIG_BISECT = /home/test/˘onfig-bad +# CONFIG_BISECT = /home/test/config-bad # MIN_CONFIG = /home/test/config-min # BISECT_MANUAL = 1 # |