summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)Author
2009-05-18i.MX31: Add support for the CPLD on PDK Debug board.Magnus Lilja
The i.MX31 PDK consists of several boards, one of them is a debug board containing a CPLD which controls some debug leds, switch buttons, an interrupt chip and an Ethernet controller. This patch adds support for detecting if the PDK board is present (during boot) and adds the interrupt chip to the kernel. Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-17mx3fb: Issue prettier log messageSascha Hauer
Without this patch we end up with a log message like "mx3_sdc_fb mx3_sdc_fb: mx3fb: fb registered". That's two fb too much for my taste. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-16i.MX31: Restructure UART setup for PDK board.Magnus Lilja
Restructure UART pin setup in preparation for adding other pins in later patches. Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-16ARM MXC: Make-sure-ipg_per_clk-is-generated-by-ipg_clk-and-not-usb_pllAlberto Panizzo
From ff1fd9d7015d9b9ad3e0df2016d0415e2719747c Mon Sep 17 00:00:00 2001 From: Alberto Panizzo <maramaopercheseimorto@gmail.com> Date: Fri, 15 May 2009 17:21:21 +0200 Subject: [PATCH] Make sure ipg_per_clk is generated by ipg_clk and not usb_pll Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-16i.MX31: Add NAND device driver for Litekit board.Magnus Lilja
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-13FB: fix unsafe use of disable_irq() in mx3fb.cGuennadi Liakhovetski
mx3fb.c calls disable_irq() from a DMA callback, i.e., in an IRQ-handler context, which has always been unsafe, and became deadly after the merge of threaded interrupt handler support. Use disable_irq_nosync() instead. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx31: changed CONSISTENT_DMA_SIZE to 8M for mx31 videoValentin Longchamp
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx31: add camera deviceValentin Longchamp
This adds the camera device based on Guennadi's soc_camera architecture for the mx31. The proposed init by Guennadi was removed and must be implemented in the board init file as it contains a lot of board specific info (memory size, clock speed). Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx31moboard: add support for usb OTG device (v3)Valentin Longchamp
This is used on all board of our system, so again this is done in the mx31moboard.c file. changes since v2: call to gpio_request added in platform code, and moved device initialization in baseboard files. changes since v1: pins are claimed in another patch Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx31: calls to gpio_request moved into platform codeSascha Hauer
In order to use the gpiolib, we now have to call gpio_request in the plaform code since it is not done in iomux code anymore. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx31: remove gpio_request calls from iomux codeValentin Longchamp
Since iomux code is not directly related to gpio on mx31, the calls to gpio_request are removed from iomux.c file. These calls have to be done in platform initialization files. The name of the singe pin call for iomux is also changed to mxc_iomux_alloc_pin. Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07MXC qonq: mxc_map_io is now mx31_map_ioSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mxc: fix wrong register access in timer codeSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx1ads: rename mxc_map_io to mx1_map_ioSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx1: add missing includeSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx1ads: setup iomux pins at onceSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx1ads: remove ifdefs, reorder include alphabeticallySascha Hauer
header is part of the kernel now. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07ARM: add USB device support to pcm037Guennadi Liakhovetski
Add OTG device definition and resources to i.MX31 and a pure USB device mode support to the pcm037 board. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07PCM038: Remove unnecessary ifdefs, reorder includes alphabeticallySascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07pcm038: Setup all iomux pins at onceSascha Hauer
Also, remove usage of set_irq_type after request_irq. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07MX27ADS: Add SDHC supportVladimir Barinov
Add SDHC support for MX27ADS board Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07MX27ADS: Add 1-wire supportVladimir Barinov
Add 1-wire support for MX27ADS board Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07MX27ADS: Add framebuffer supportVladimir Barinov
Add Sharp-QVGA panel support for MX27ADS board Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07MX27ADS: Add I2C supportVladimir Barinov
Add I2C support for MX27ADS board Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07MX27ADS: Add NAND supportVladimir Barinov
Add NAND support for MX27ADS board Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07MX27ADS: setup all pins at once in one tableVladimir Barinov
Setup all pins at once in one table Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07i.MX31: Add ethernet support to i.MX31 Litekit board.Magnus Lilja
This patch adds the SMSC platform device to the Litekit board. Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07i.MX31: Correct comments on CONFIG_DEBUG_LL.Magnus Lilja
Several comments in board config files stated "mandatory for CONFIG_LL_DEBUG" but the correct name is CONFIG_DEBUG_LL. Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07i.MX31: Removed unused items from board-mx31lite.h.Magnus Lilja
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07i.MX31: Add UART1 device to Litekit board.Magnus Lilja
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx31moboard: add sdhc support (v3)Valentin Longchamp
This support both sdhc1 and sdhc2 with WP and CD for the marxbot and devboard mx31moboard baseboards. sdhc2 is present on both, but is not directly included in the mx31moboard file because a third baseboard (not supported yet) without sdhc2 is planned. Changes since v1: removed pin initialization from init/exit function and taken different comments into account Changes since v2: pin initialiation now is done in another patch for all current mx31moboard pins Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx31moboard: add i2c support (v2)Valentin Longchamp
Changes since v1: all the pins needed for the drivers are claimed in another patch Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx31moboard: setup all pins (v2)Valentin Longchamp
As suggested by Sascha, here we setup all the pins that we are using in the current (and currently reviewed) drivers for mx31moboard system. changes since v1: changed I2C1 pin names Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx31: define various pins used on mx31moboard (v2)Valentin Longchamp
As suggested by Sascha, I regroup them in a single patch so that the other patches become more orthogonal. changes since v1: changed I2C1 pin names Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07i.MX31: Add hw-random for RNGAAlan Carvalho de Assis
This hw-random driver add support to RNGA hardware found on some i.MX processors. Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com> Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mx31moboard: clean-up of board supportValentin Longchamp
Various improvements (includes in alphabetical order, platform devices declaration order change, ...) The pins now are claimed in a single function call from a main table for every board for a better clarity and to adopt the current agreement for mx31 devices. Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07MX27: Add basic support to MX27PDKFabio Estevam
This patch adds basic support to MX27PDK board http://www.freescale.com/imx27pdk ). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07MXC: mx2_defconfig fileIvo Clarysse
Adds a defconfig file for the i.MX21 SoC, targeting the Freescale i.MX21ADS (M9328MX21ADSE) Application Development System. Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07imx: re-work of PWM, add i.MX21 supportHolger Schurig
* Kconfig enables now HAVE_PWM (this enables in turn the selection of CONFIG_BACKLIGHT_PWM) * changes CONFIG_ARCH_MXyy to CONFIG_MACH_MXyy * fix some register names to match those of the reference manual * write a stub code so that the PWM can be used to program the LCD backlight * convert from #ifdef CONFIG_ARCH_MXxx to cpu_is_mxXX() * remove unneeded defines and fix 80-column "violations" of checkpatch.pl Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07MXC: mx21ads base supportIvo Clarysse
[PATCH v6] MXC: mx21ads base support Base machine support for the Freescale i.MX21ADS (M9328MX21ADSE) Application Development System. Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07ARM: framebuffer support for pcm037Guennadi Liakhovetski
Add support for a QVGA Sharp LCD on pcm037. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mxc: emulate GPIO interrupt on both-edgesGuennadi Liakhovetski
MXC GPIO controller does not support generation of interrupts on both edges. Emulate this mode in software by reconfiguring the irq trigger polarity on each interrupt. This follows an example of drivers/mfd/asic3.c. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07imx: exit functions can/should be voidHolger Schurig
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07[ARM] remove arch-imxSascha Hauer
arch-imx is superseeded by the MXC architecture support. This patch removes arch/arm/mach-imx from the kernel. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07[ARM] Remove arch-imx from build systemSascha Hauer
arch-imx is superseeded by the MXC architecture support. This patch removes arch-imx from the build system. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mxc irq: make architecture runtime dependentSascha Hauer
Currently we depend on hardcoded base addresses for the interrupt controller. This prevents us from compiling in more than one i.MX architecture at a time. This patch changes the base address to a runtime calculated one. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07mxc timer: make compile time independentSascha Hauer
Currently we depend on hardcoded base addresses for the timer. This prevents us from compiling in more than one i.MX architecture at a time. This patch changes the base address to a runtime calculated one. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07MXC: rename mxc_map_io to architecture specific versionsSascha Hauer
This allows us to have more mapping functions for more than one i.MX architecture in the kernel. As this is the earliest board specific hook we have, also use it to set the cpu type. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07pcm037: Add support for UART2Sascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07MX35: Fix IPU/Framebuffer clock namesSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-27 09:17:55 +0000