| Age | Commit message (Collapse) | Author |
|---|
|
As noted by Matthew Wilcox:
Kyle McMartin just tracked down a bug on parisc to a missing
"memory" clobber in the inline assembly implementation of
ip_fast_csum. The FRV, SH and Xtensa ports are also missing a
memory clobber, so I thought it would be polite to let you know.
The bug manifests as dropped network packets (obviously they have
the wrong checksum). It started appearing for parisc with GCC 4.3.
The GCC manual says:
If your assembler instructions access memory in an unpredictable
fashion, add `memory' to the list of clobbered registers. This
will cause GCC to not keep memory values cached in registers
across the assembler instruction and not optimize stores or loads
to that memory.
I see that FRV has a 400 byte memory output which may prevent this
problem from appearing, but SH and Xtensa have nothing to prevent
this bug. Hope this saves you a few days of debugging.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Replace the COPY_UNALIGNED_WORD helper.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch fixes the following build error caused by
commit a1dc4b59fa4af97ae68ee214d4d72bbd7c7ec1dc
(sh: intc_sh5 depends on cayman board for IRQ priority table.):
<-- snip -->
...
CC arch/sh/kernel/cpu/irq/intc-sh5.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c: In function 'plat_irq_setup':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c:257: error: expected declaration or statement at end of input
make[4]: *** [arch/sh/kernel/cpu/irq/intc-sh5.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
When we introduced support for KBUILD_EXTRA_SYMBOLS
we started to include the externam module's kbuild
file when doing the final modpost step.
As external modules often do:
ccflags-y := -I$(src)
We had problems because $(src) was unassinged and
gcc then used the next parameter for -I resulting in
strange build failures.
Fix is to assign $(src) and $(obj) when building
external modules.
This fixes: http://bugzilla.kernel.org/show_bug.cgi?id=10798
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Tvrtko <tvrtko.ursulin@sophos.com>
Cc: Andrea Arcangeli <andrea@qumranet.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
|
|
As Russell pointed out, original patch will break some serial configurations
because of the dependency of the <asm/serial.h> header file.
Revert it first and try to find out other solution later
Cc: Javier Herrero <jherrero@hvsistemas.es>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
AD7877 use SSEL_2 (P9.9) and IRQ_PF8 (P9.14) on BF527
- populating JP3 to enable STAMP
- disable SW11.2 to disconnect SSEL_2/PF12 from Rotary NAND
- disable SW18.1 to disconnect SSEL_2 from MAX1233 touchscreen chip
Signed-off-by: Bryan Wu <cooloney@kernel.org>
|
|
The node for DMA2 in the MPC8610 HPCD device tree has the wrong compatible
properties. This breaks the DMA driver and the sound driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Currently ext4 and fuse fail to link if modular:
ERROR: "copy_page" [fs/fuse/fuse.ko] undefined!
ERROR: "empty_zero_page" [fs/ext4/ext4dev.ko] undefined!
make[3]: *** [__modpost] Error 1
make[2]: *** [modules] Error 2
make[1]: *** [sub-make] Error 2
While arch ppc exists it may as well compile, so this exports those
symbols (which are already exported in arch/powerpc).
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Gcc might re-order MMIO accessors vs. surrounding consistent
memory accesses, which is a "bad thing", and could break drivers.
This fixes it by adding a "memory" clobber to the MMIO accessors,
which should prevent gcc from doing that reordering.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The following patch is seems to fix the tulip suspend/resume panic:
http://bugzilla.kernel.org/show_bug.cgi?id=8952#c46
My attempts at a cleaner patch failed and Pavel thinks this is OK.
Original from: kernelbugs@tap.homeip.net
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
When using 4+ GB RAM and SWIOTLB is active, the driver corrupts
memory by writing an skb after the relevant DMA page has been
unmapped. Although this doesn't happen when *not* using bounce
buffers, clearing the pointer to the DMA page after unmapping
it fixes the problem.
http://marc.info/?t=120861317000005&r=2&w=2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Because we cache the last failed-to-xmit packet, if there are no
packets queued behind that one we may never send it (reproduced here
as TCP stalls, "cured" by an outgoing ping).
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
If we fail to transmit a packet, we assume the queue is full and put
the skb into last_xmit_skb. However, if more space frees up before we
xmit it, we loop, and the result can be transmitting the same skb twice.
Fix is simple: set skb to NULL if we've used it in some way, and check
before sending.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Update myri10ge version to 1.3.99-1.347.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Commit 5a0a92e67b5009a71e011658da04fb92dad8961f mentions len < ETH_ZLEN
is true for ARP packets. This obviously is not unlikely.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
After request_dma() succeeding, any error path should do free_dma().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This is normal when the external link is down so don't report it as an error.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: change the Device IDs of nvidia MCP7B AHCI controller in ahci.c
[libata] sata_fsl: Fix broken driver, add port multiplier (PMP) support
libata: SRST can't be trusted on PMP sil3726
libata: fix libata-scsi kernel-doc notation
ata: Convert to static DEFINE_SPINLOCK(lock)
ata_piix: fix macbook ich8m problems
sata_mv: implement SoC guideline SATA_S11
sata_mv: workaround for 60x1 errata sata13
sata_mv: nuke unreleased GenIIe revisions
sata_mv: PHY_MODEx errata fixes
sata_mv: move SOC_FLAG to hpriv
|
|
This patch silences the build warnings concerning o2net_init_nst()
and friends when building without CONFIG_DEBUG_FS enabled.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
|
|
This patch silences the build warnings concerning dlm_debug_init()
and friends when building without CONFIG_DEBUG_FS enabled.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
|
|
This patch silences the build warnings concerning o2net_debugfs_init()
and friends when building without CONFIG_DEBUG_FS enabled.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
|
|
The static structure describing the userspace cluster plugin for ocfs2
was named 'user_stack', which is a real pain when people are grep(1)ing
the tree for the program stack object 'user_stack'. Change the name to
something distinct and namespaced.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
|
|
.. because it is.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Initialize all proper structure members in order to support
work-list vport processing. This code also properly acquires the
correct (physical hardware_lock) lock during work submission.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
handling."
This reverts commit bd2a1846b2313e32d0270151a31a6b8335384a20.
The original (prior to the reverted commit) code was correct.
Additionally, the vp_idx should be checked during MBA_PORT_UPDATE
in order for proper handling to take place for a given vport.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: notify on empty
virtio: force callback on empty.
virtio_blk: fix endianess annotations
virtio_config: fix len calculation of config elements
virtio_net: another race with virtio_net and enable_cb
virtio: An entropy device, as suggested by hpa.
virtio_blk: allow read-only disks
lguest: fix ugly <NULL> in /proc/interrupts
virtio: set device index in common code.
virtio: virtio_pci should not set bus_id.
virtio: bus_id for devices should contain 'virtio'
Fix crash in virtio_blk during modprobe ; rmmod ; modprobe
lguest: use ioremap_cache, not ioremap
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: fix rpadlpar pci hotplug driver sysfs usage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: rename SW_RADIO to SW_RFKILL_ALL
Input: gtco - fix double kfree in error handling path
Input: pxa27x_keypad - miscellaneous fixes
Input: atkbd - mark keyboard as disabled when suspending/unloading
Input: apanel - remove duplicate include
Input: wm9713 - support five wire panels
Input: wm97xx-core - fix race on PHY init
Input: wm97xx-core - fix driver name
Input: wm97xx-core - report a phys for WM97xx touchscreens
Input: i8042 - make sure Dritek quirk is invoked at resume
Input: i8042 - add Dritek quirk for Acer TravelMate 660
|
|
* Wim Van Sebroeck <wim@iguana.be> wrote:
> Author: Jordan Crouse <jordan.crouse@amd.com>
> Date: Mon Jan 21 10:07:00 2008 -0700
>
> [WATCHDOG] Add a watchdog driver based on the CS5535/CS5536 MFGPT timers
-tip testing found the following build failure on latest -git:
drivers/watchdog/geodewdt.c: In function 'geodewdt_probe':
drivers/watchdog/geodewdt.c:225: error: too many arguments to function 'geode_mfgpt_alloc_timer'
make[1]: *** [drivers/watchdog/geodewdt.o] Error 1
make: *** [drivers/watchdog/geodewdt.o] Error 2
with this config:
http://redhat.com/~mingo/misc/config-Fri_May_30_15_19_52_CEST_2008.bad
find the fix below.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When Greg "fixed" the sysfs usage of that driver a while back, he seem
to have introduced a bug where the quotes are added around the name of
our specific sysfs files, thus breaking the user space tool.
This fixes it. Tested DLPAR operations on a POWER6 machine successfully.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Change the partial Device IDs of nvidia MCP7B AHCI controller in ahci.c,
as the actual PCI IDs deployed in the field differed from the forecasted ones
preemptively placed in the driver.
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The following commit (4c9bf4e799ce06a7378f1196587084802a414c03):
libata: replace tf_read with qc_fill_rtf for non-SFF drivers
Broke the sata_fsl.c driver in 2.6.26-rc. I know the following patch fixes
the issue, it clearly also adds port multipler support. The current
2.6.26-rc driver is broken.
On boot with debug enabled we get something like (w/o this patch):
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
.. continues for ever.
This change fixes this as a side effect of adding port multiplier support.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
As in sil4726, SRST can't be trusted on sil3726 causing detection
problems under certain configuraitons. I thought it was from the
Config Disk device but apparently not.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix libata-scsi kernel-doc notation:
Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1659): No description found for parameter 'cmd'
Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1971): No description found for parameter 'buf'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Replace deprecated static spinlock_t instance to static DEFINE_SPINLOCK(lock).
Signed-off-by: Pradeep Singh <rautelap@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
ICH8M on macbooks are peculiar in that some of them lock up when the
second port is enabled, some return bogus values on SIDPR access while
yet others hang on SIDPR access. Also, the ich8m_apple_sata entry was
wrongly added below generic ich8m entry making it virtually useless.
This patch works around macbook ich8m problems by
* moving ich8m_apple_sata entry above generic ich8m entry
* dropping PIIX_FLAG_SIDPR from ich8m_apple_sata
* adding subsystem 106b:00a1 as ich8m_apple_sata
Reported and tested by MATSUBAYASHI.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: MATSUBAYASHI 'Shaolin' Kohji <shaolin@rhythmaning.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The 5182 System-On-Chip (SOC) variant wants certain lower
bits to be cleared on any write to the PHY_MODE3 register.
If/when support is added for other SOC variants, we'll need
some way to uniquely identify the 5182, and not perform this
workaround for the others.
But for now, it is the only SOC variant we support here.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The "B2" variant of the 6041/6081 (genII) chips requires
that the PHY_MODE3 register be rewritten after any write
to PHY_MODE4.
This fixes a regression introduced by an earlier patch.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The only public release of the 6042/7042 chips was/is revision "B0".
Remove code that attempted to deal with earlier, non-released revs.
This matches the logic of the current Marvell "proprietary" driver.
Also, bump up the sata_mv version number, to reflect this batch of erratas.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix and update the errata handling for the PHY_MODEx registers.
This improves receiver noise tolerance, among other things.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Convert the System-on-Chip flag from a host flag to an hpriv flag,
for better consistency with other chip-rev flags, and for easier use
in errata fixes etc.
Also change the related "HAS_PCI()" into "!IS_SOC()" for better consistency
of naming/use (everything else SOC-related already uses "SOC").
There are no functionality changes in this patch.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Set the proper model for LG LS75 with CM9880 codec.
See ALSA bug#2105:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=2105
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
llc: Fix double accounting of received packets
netfilter: nf_conntrack_expect: fix error path unwind in nf_conntrack_expect_init()
bluetooth: fix locking bug in the rfcomm socket cleanup handling
mac80211: fix alignment issue with compare_ether_addr()
mac80211: Fix for NULL pointer dereference in sta_info_get()
mac80211: fix a typo in ieee80211_handle_filtered_frame comment
rndis_wlan: add missing range check for power_output modparam
iwlwifi: fix rate scale TLC column selection bug
iwlwifi: fix exit from stay_in_table state
rndis_wlan: Make connections to TKIP PSK networks work
mac80211 : Fixes the status message for iwconfig
rt2x00: Use atomic interface iteration in irq context
rt2x00: Reset antenna RSSI after switch
rt2x00: Don't count retries as failure
rt2x00: Fix memleak in tx() path
mac80211: reorder channel and freq reporting in wext scan report
b43: Fix controller restart crash
mac80211: fix ieee80211_rx_bss_put/get imbalance
net/mac80211: always true conditionals
b43: Upload both beacon templates on initial load
...
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Update default configuration.
[S390] disassembler: fix idte instruction format.
[S390] tape: fix race with stack local wait_queue_head_t.
[S390] 3270: fix race with stack local wait_queue_head_t.
[S390] dasd: use a generic wait_queue for sleep_on
[S390] sclp_vt220: fix scheduling while atomic bug.
[S390] showmem: Only walk spanned pages.
[S390] appldata: prevent cpu hotplug when walking cpu_online_map.
[S390] Fix section mismatch warnings.
[S390] s390 types: make dma_addr_t 64 bit capable
[S390] tape: Fix race condition in tape block device driver
[S390] fix sparsemem related compile error with allnoconfig on s390
|
|
In this case we want a constant pointer to constant chars:
drivers/misc/thinkpad_acpi.c:3824:19: error: Just how const do you want this type to be?
Like the error says.
drivers/misc/thinkpad_acpi.c:3863:19: error: Just how const do you want this type to be?
drivers/misc/thinkpad_acpi.c:3864:19: error: Just how const do you want this type to be?
drivers/misc/thinkpad_acpi.c:3865:19: error: Just how const do you want this type to be?
drivers/misc/thinkpad_acpi.c:3866:19: error: Just how const do you want this type to be?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
